User Manual Satlock MagicFINDER Plus English
Contents
1. Noise Filter may be activated to prevent the display of this field In this case SUPP will be displayed in line 4 and the section remaining under the curve will not be drawn With the DisegC option in the last line any DiseqC port may be selected Through this signals received from various ports may be compared The spectrum screen may be used during satellite search as it operated fast After LNB is set in a way that the values on the screen are at the highest level it is possible to find to which satellite the curve belongs to with the Quick Satellite Identification function Pressing the OK Button is enough for this process MagicFINDER Digital SatLock Operating Manual If the satellite can be identified the satellite name will be written on top of the Spectrum Graph The satellite identification system operates similarly to the previous menus Thus the same precautions are valid for this screen as well The Back Button is used to exit from these screens SETTINGS Mitt Egal KHPALI Sl O En i A E aji E f ISAN TURELE This is the section in which all device settings are made The required parameter is selected with the Function Selection Buttons and the value may be changed with the Value Change Buttons In line 1 the LNB Type is selected In line 2 the DiseqC port selection is made It must be left closed at times it is not used Measurement operations will2. 1A Adapters with a lower value may not charge the batteries fully even if you see the charging message on the screen e It is recommended that you do not use the device during the charging process Because the ground returns between the network to which the charger adapter is connected and the networks of sources such as LNB Receiver Multiswitch with which measures are taken may cause serious damage on the device The device must be simultaneously grounded from a single point only e There may be decrease in the battery performance in very cold weathers due to the chemical structure of lithium ion batteries This is normal MagicFINDER Digital SatLock Operating Manual LNB Short Circuit Protection The SatLock device LNB power supply unit is equipped with an active short circuit protection system When the LNB input is short circuited or draws an above normal current during measurement the short circuit protection is enabled and SHORT CIRCUIT is displayed on the screen Also an audible alert is sounded with a constant beep When the short circuit or the over current state is eliminated the device returns to the last function in which measurement was made and the measurement process is stopped The measurement process should be restarted after troubleshooting Short circuits do not cause any damage to the device MAIN MENU You can select the menu that you want to use with the Function Selection Buttons and by press
3. at mi i E m Bika p Is m ISE USER MANUAL GENERAL FEATURES Easy to understand user friendly menu and keypad LNB short circuit protection Display of Analog Signal Level Digital Signal Quality with and Bar audible notification Timer Lock Data Lock and Digital Signal FEC type display Display of Digital Signal QBER Bit Error Ratio with Quantity and Bar Display of timing detection and shift Display of true carrier wave frequency and shift Rapid spectrum analysis and display and satellite recognition function Language options of Turkish English Dutch and German Satellite and TP list updating with the RS232 connection Automatic shut down function Quick charge system and long term use with a single charge DisegC Command support and DisegC scanning function for Multiswitch and DisegC switches 32 Satellites 256 TP Memories RS232 Connection E m M k Digital Satlock Graphic LCD Screen MagicFINDER Power Button A amp Value Change Buttons IA D Function Selection Buttons IN x s Back Button AST OK Button Charger Adapter Input 6 LNB Input e LNB Output MagicFINDER Digital SatLock Operating Manual Turning the device ON OFF To turn the device ON hold the Power Button pressed for approximately 2 seconds The logo will be displayed on the screen and the device will become ready for use To turn the device OFF atthe Main Menu hold the Power Button
4. and if there is an attempt to identify which satellite this data belongs to and the attempt is a successful one the name of the satellite identified is written on the screen This is how the satellite identification system works At the moment any digital data is identified it is compared to the first TP information for the top 12 satellites in the memory If any of the top 12 satellites are in accord with the TP s in the top rows the name of the satellite in accord is written Therefore do not forget that when updating TP information from the PC only the top 12 satellites are used in this function Also since only the first TP information for the top 12 satellites are going to be compared make sure that the first TP information are current Otherwise this function will not operate well Furthermore to accelerate the speed of Satellite identification make sure that the Symbol rate for the first TP information is high Because TP s with high symbol rates can technically be detected much quicker The recommended Symbol rate is at least 22MS Seconds Finally to prevent incorrect identification on this screen make sure that the first TP information that you have entered does not conflict amongst different satellites For example if there is a TP on Hotbird and Turksat with the Same frequency and symbol rate do not write this in the first row The Back Button is used to exit from this screen MagicFINDER Digital SatLock Op
5. ater the 100 section of the battery capacity will be filled in a healthy way with slow charge If the device is OFF when the charge process is started a battery image will be displayed on the screen and the charge status can be monitored with the moving bar in the battery If the charge process is started when the device is ON the same visual monitoring may be performed with the battery icon in the top right hand corner A moving bar will be displayed in the battery when quick charge is continuing When the quick charge process is completed a full battery image is displayed which means that 80 of the device battery has been filled and the device is ready for use However there is benefit in leaving the device on charge for 1 more hour for the battery capacity to be 100 full with the slow charge process e The total charge time for completely discharged batteries may exceed 2 hours e If the device is in use during the charging process the charge time will be longer e If the device is not going to be used for a long time you must fully charge it in order to prevent the lifespan of batteries from shortening e Even if the device is not going to be used for a long time it is recommended that you charge it max once every three months Because if lithium lon batteries are left uncharged for long periods their lifespan may shorten e Do not apply voltage higher than 24VDC on the charge input e Use amin charger adapter of 12VDC
6. be accelerated because of this If a value is selected here the device will spend time to send the required DisegC commands before each measurement In line 3 the intensity of the screen backlight may be adjusted It is recommended that you do not keep it any higher than necessary Because it will decrease the lifespan of your battery even if by little In line 4 the device volume output may be turned up and down In line 5 the device language may be selected If the OK Button is pressed after the selections are made the changes are saved and the device returns to the Main Menu If the Back Button is used you will return to the Main Menu without saving the changes that were made MagicFINDER Digital SatLock Operating Manual Technical Specifications 8 4V 2000mA Lithium Ion Type LNB Signal Level 65dBm 25dBm LNB Input Socket F Female Type F Female Type o LNB Feeder 13 18V Max 600mA 0 22KHz 1Vpp modulation With short circuit protection DisegC Multiswitch DisegC Multiswitch DisegC Interface 2 0 Satellite Memory Number of TP s Per Satellite 8 Total 32x8 256 TP Supported LNB s Universal OneTouch Single C Single MagicFI NDER Digital SatLock Operating Manual Mag c FINDER PLUS EXLUSIV DISTRIBUTOREN EUROPA Sonnenschein Kommunikationstechnik Rantex GmbH Langenberger Str 126a Oberstrasse 75 45277 Essen 20149 Hamburg http www so mm de http www satmarket de Al
7. e made as the Signal Noise rate increases If both Timing and Data are caught the LOCK icon appears next to the key icon In this case it means that the LNB setting is completed MagicFINDER Digital SatLock Operating Manual You may use the OK Button to reach detailed information such as more precise setting and OBER True Frequency See IN When you enter the sensitive adjustment screen the TP name selected in the title section is displayed Respectively FOR and the true carrier frequency in which the broadcast is BDR and the true Symbol Seconds ratio for the broadcast the FEC Value and the OBER rate are displayed The frequency shift LNB may be determined by checking the values in the first two lines Also the key values for the Carrier Wave and Timing loop are specified with the key icons to the right of the lines If a question mark is displayed this means that the carrier wave or the timing value has not been determined In the BER section the error rate is displayed in writing and with the Bar The lower the BER rate the better and cleaner the quality of the broadcast Sensitive adjustment may be made in LNB with the BER indicator The Back Button is used to exit these screens SATELLITE DETECTION IDENTIFICATION nie Fr m M rth ee rer i On this screen the S and Q show the Analog Signal Level and the Digital noise rate like in the Manual search menu If a digital data is caught
8. erating Manual DisegC SEARCH In Multiswitch systems this menu is used to figure out which satellite is in which channel The potential 4 DisegC port is scanned If any digital data is caught an attempt is made to identify which satellite the data belongs to and if identified it is written next to the relative DisegC port The satellite identification system is identical with the Satellite Search Identification menu Thus the same measures are valid for this screen as well The Back Button is used to exit from this screen SPECTRUM ANALYSIS Spectrum Analysis is the screen which enables the display of the analog signal levels received by scanning the frequency band in the 950 2150 MHz range on the graphic screen The peak points on the screen show the parts that are strong in terms of the signal With the options on the right hand side ofthe screen respectively the Horizontal Vertical polarization selection Upper Lower band selection Signal level Noise Filter DisegC port selection may be made You can move to the desired option with the Function Selection Buttons and make the selection with the Value Change Buttons The graph on the screen is examined after the Polarization and Band selection is made If the signal levels are very low or very high the dB value may be changed to enable easy monitoring Generally the noise section that remains low at the spectrum curve does not mean anything The
9. ing the OK Button you enter the selected menu When in this screen the device may be turned OFF by holding the Power Button pressed for 2 seconds Other buttons are nonfunctional in this screen MANUAL SEARCH In line 1 one of the 32 satellites in the memory are selected To change the satellite you move to the UYD satellite line with the Function Selection Buttons and change the satellite with the Value Change Buttons By holding the Value Change Buttons you can change quickly between the satellites In line 2 one of the 8 TP s entered for the relative Satellite is selected The selection method is the same You go to the PRG line with the Function Selection Buttons and change the TP with the Value Change Buttons In line 3 as TP is changed the Frequency Polarization and Symbol Rate will be displayed for the selected TP The OK Button is used to start the signal measurement process The Back Button may be used T 1 1 5 T ksat PRG TRT Turk LOCK 11634 H 644 E u JH Er IE I In the measurement screen S and the Analog Signal Level are displayed as and Bar If the digital carrier cannot be caught SEARCHING is displayed in line 2 When the Timing Value for the Digital Signal is caught the key icon Is displayed under PRG and the Digital Signal Band Noise rate is given in the bottom line with Q Also an increasing audible alert and LNB setting may b
10. le Inhalte dieses Internetangebotes insbesondere Texte Fotografien und Grafiken sind urheberrechtlich gesch tzt Copyright Das Urheberrecht liegt soweit nicht ausdr cklich anders gekennzeichnet bei Riccardo Rossini Rantex GmbH Ralf Sonneschein Sonneschein Kommunikationstechnik Bitte fragen Sie Riccardo Rossini Ralf Sonneschein falls Sie die Inhalte dieses Internetangebotes verwenden m chten Wer gegen das Urheberrecht verst t z B die Inhalte unerlaubt auf die eigene Homepage kopiert macht sich gem 106 ff Urhebergesetz strafbar Er wird zudem kostenpflichtig abgemahnt und muss Schadensersatz leisten Kopien von Inhalten k nnen im Internet ohne gro en Aufwand verfolgt werden
11. pressed for approximately 2 seconds The device will shut down e Ifthe battery level is very low the device may not turn ON Please wait until the charging process Is completed e If the battery level drops below the critical level while the device is in use the device will shut down automatically This may be monitored with the flashing battery image on the top right hand corner when the critical level is reached Automatic Shut Down Function The SatLock device is equipped with the automatic shut down function to prevent unnecessary energy consumption If the device is idle for approximately 5 minutes in any menu without pressing any keys it will first automatically exit the menu in use and return to the main menu If no operation is performed for the 5 minutes after this the device will shut down automatically Battery Charge System The SatLock device is supported with high technology Lithium lon batteries This allows a long period of measuring and adjustment with a single charge Furthermore as these batteries have no memory impact they may be charged whenever desired There is no need to wait until they are completely discharged The SatLock device charges batteries in two stages The charging process will start when you attach the 12VDC charger adapter or the vehicle charger apparatus provided with the device to the Charger Adapter Input According to the state of the battery first quick charge will be applied and l
Download Pdf Manuals
Related Search