ParkIT Install Guide
Contents
1. During the cleaning process avoid scratching the front cover Never use the camera without its sunshield as it was specially designed to protect the device against environmental effects such as heat moisture or contamination The cameras should be stored in low humidity environment in the temperature range of 35 C 55 C NOTE The startup temperature of the camera is 20 C ParklT Install Guide Page 12 14 Appendix Adding Alternate IP Address Windows Vista Windows 7 Click Start and select Control Panel Make sure you are in Classic View by clicking Classic View on the left of the Control Panel Open Network and Sharing Center Click Manage Network Connections on the left side of Network and Sharing Center Right click on the network connection you want to add an IP address for to which the camera has been connected and select Properties Select Obtain an IP address automatically and click on the Alternate Configuration tab Select User configured and enter e g the 192 0 2 54 IP address and 255 255 255 0 as Subnet mask as shown on Figure 1 Click OK in the opened windows Windows XP Click Start and select Settings Control Panel Make sure you are in Classic View by clicking Classic View on the left of the Control Panel Click Network Connections Right click on the network connection you want to change the IP address of to which the camera has been connected and sele2. reasonable protection against harmful interference when the equipment is operated in a commercial environment This product generates uses and can radiate radio frequency energy and if not installed and used in accordance with the manufacturer s instruction manual may cause harmful interference with radio communications Operation of this product in a residential area is likely to cause harmful interference in which case you will be required to correct the interference at your own expense This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation Notice The FCC regulations provide that changes or modifications not expressly approved by ARH Inc could void your authority to operate this equipment These limits are designed to provide reasonable protection against harmful interference in a non residential installation However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference with radio or television reception which can be determined by turning the equipment off and on you are encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the antenna of the radio television receiver e Increase the separa
3. EEVES BEFORE CONNECTING TO POWER IN ORDER TO AVOID DAMAGES DUE TO SHORT CIRCUIT POWER SPECIFICATIONS a ParkIT WideVGA ParkIT 1 3MP DC Input 12V nominal 11V 15V reverse polarity protected Power NM OwA Input Current 1 0A 1 1A max 2 5A transients occur for a few msecs Over current Protection ParkIT Install Guide max 2 5A transients occur for a few msecs by fuse Page 7 14 Adaptive Recognition Hungary TRIGGER SPECIFICATIONS Logic output Open Collector max 12Vpc max 10mA Input min 5V max 12V Pulse width min 1 ms SERIAL CONNECTION The serial port of the camera complies with the RS 232 standard Sample application for trigger input and output OPTO OUT max 10mA 1 OPTO OUT max 10mA Ul E 1 i 1 D IK 1W OPTO IN max 12 V DC EATERNAL WIRING SCH EMATIC 3 2 Ethernet Connection The camera is equipped with CAT5e UTP crossover cable with RJ45 plug It is ready to connect both to PC and network switch directly NOTE The RJ45 plug is not weatherproof 4 Software Requirements The ParkIT camera is developed to operate without any kind of special software Software requirements e For network setup administrator root privileges are necessary e Web browser Mozilla Firefox 4 Internet Explorer 8 Google Chrome 14 X X X or later editions NOTE To enable all camera functions enable and update JavaScript and ActiveX controls in your browser Pa
4. ParklIT ANPR Camera Install Guide Copyright by ARH Inc www ARHUNGARY hu Adaptive Recognition Hungary ParkIT Install Guide For versions from 1 12 0 8 Document version 12 07 18 Table of Contents Ho 5 e g 8 eee ee eee eT Tere Ter eter eT LeO Ne LORS DTIC CE IEE TOUS OORT IE OR De IEL TRE wee y mag nec may pect mee rr eter tere 3 LE N N N E E 4 ER EEA AAEN AE 6 PAN e o re E E EA EEA dana EAEE ENEE EAE EEE EEEE EEEE A A EA TT ETT l Po I Re E a a AE EEEE l sPower Taigaen Seral Onne NOT eisirean TT dintete T SE E aig aaa TA 8 A Sonae Redare meni rrin rA sienna ert 8 r E EAE E IE I EO NA E N 9 6 Recommended Camera POSION sssrin EEEE EEE 10 Fee E E EEEE EEEREN A 12 PE E AAAA E EE E A 13 ae a a E A A A AEA AAA EAEN 14 WARNING The camera emits invisible high power infrared light Prolonged direct exposure to this radiant energy can cause permanent damage to the eye ParklT Install Guide Page 2 14 Compliances CE Certificates The ARH ParkIT ANPR digital camera family complies with the European CE requirements specified in the EMC Directive 89 336 EEC The ANPR cameras conform to the following Product Specifications Emission EN 55022 EN 55024 Immunity EN 61000 4 2 3 4 5 6 8 11 FCC Compliance This product has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide
5. airs may be executed by the manufacturer only Office address Service address ARH Inc ARH Inc 41 Alkotas Road lpari Park HRSZ 1113 1 HU 1123 Budapest HU 2074 Perbal Hungary Hungary Phone 36 1 2019650 Phone 36 1 2019650 Web www arh hu Web www arh hu Email support arh hu Email rmarequest arh hu ParklT Install Guide Page 14 14
6. ct Properties On the General tab click once the Internet Protocol TCP IP item and click Properties Select Obtain an IP address automatically and click on the Alternate Configuration tab Select User configured and enter e g the 192 0 2 88 IP address and 255 255 255 0 as Subnet mask as shown on Figure 2 Click OK in the opened windows 1 Open a terminal 2 Enter the ifconfig command to see the reserved Ethernets e g et h0 3 Enter the following command ifconfig eth Y 192 0 2 25 Internet Protocol Version 4 T CP IPv4 Properties Alternate Configuration If this computer is used on more than one network enter the alternate IP settings below Automatic private IP address User configured IP address 192 0 2 54 Subnet mask 255 255 255 0 Default gateway 4 168 0 Preferred DNS server k 168 0 x Alternate DNS server 38 25 Preferred WINS server Alternate WINS server Validate settings if changed upon exit Figure 7 Internet Protocol TCP IP Properties eee Alternate Configuration If this Computer is Used on more than one network enter the alternate IF settings below Automatic private IP address User configured IP address We 0 2 86 Subnet mask 255 255 255 0 Default gateway 192 768 0 1 Prefered ONS server 192 168 O0 J Alternate DONS server Preferred WINS server Alte
7. h the instructions given in its documentation This equipment contains no serviceable components Unauthorized equipment changes or modifications cause warranty to void ParklT Install Guide Page 3 14 1 Hardware Overview Sunshield Wall bracket Camera with bracket Infrared LEDs Camera optics Infrared LEDs Green status LED Light sensor Red status LED Camera front Bracket ParklT Install Guide Page 4 14 Bracket Details and Sizes ParklT Install Guide Page 5 14 Adaptive Recognition Hungary 2 Install the Bracket The bracket can be adjusted at two different points 1 Adjusting the ball joint A The bracket allows rotating the ball joint in a 35 degree spatial angle in any direction 2 Adjusting the foot B If the necessary extent of rotation exceeds 35 degrees then the foot of the bracket can be rotated by 180 extending the 35 degree spatial angle with additional 20 according to the figure B Bracket foot rotated by 180 enables additional 20 to rotate the camera by Steps of rotating the foot 1 Remove the four screws 1 located at the back of the foot Use size 4 Allen key 2 Rotate the foot 2 by 180 degrees 3 Place the screws back into the holes and screw them back on NOTE Do not overtighten the screws ParklT Install Guide Page 6 14 2 1 Mounting The bracket can be mounted into different surfaces Use app
8. nfigure the Camera The ParkIT camera must be configured before using With the Configuration Wizard the camera features e g zoom triggering etc can be set up quickly and easily Of course the use of the wizard is optional camera properties can be set up manually as well Steps of the Wizard Network setup Changing the default IP address of the camera is strongly recommended time and date settings camera task selection configuration of image properties autozoom and autofocus event managing and profile settings For more information on the Wizard see ParkIT User s Manual ParklT Install Guide Page 9 14 AREH 001 7 Yi 4 Y 100 Adaptive Recognition Hungary i 10101 ji D100 199 010 O 110 QIC 00 010 AU Ut 1990 19999 i 500 QO 000 0 D OT 710710710 Si 190301019 5101010 0101100101016 Bb 1901010191010 101 1 Web interface after configuring the camera 6 Recommended Camera Position A good ANPR engine can read plates from images captured in various conditions However to achieve over 95 recognition rate with short recognition times the position of the camera have to be calculated accurately The best position is if the angle between the camera axis and the direction of the vehicle movement is minimal see below Cmca came Q should be minimal The distance between the camera and plate is also important If the camera is too far from the plate the characters may not be la
9. rge enough for recognizing them In this case zoom in until you reach the proper size If the distance is too short it may happen that a part of the plate is over the camera s field of view when the vehicle is near to the side of the lane or the plate is not at the middle of the vehicle Generally sharp and characters easily readable to the human eye are appropriate for ANPR LPR purposes The most important factor is the size of the characters on the image For Latin characters it is recommended to have at least 16 pixel character height for Arabic or other special characters it is recommended to have 20 pixel height since they are more calligraphic than Latin characters Too large characters are also not suitable for ANPR therefore try to avoid settings where the character size is greater than 50 pixels in height A line width of a character on the image should be at least 2 pixels Page 10 14 ive iv JO o 1010111 i 07 J A 0 L99 19 4 0710 VIVUTOTO OTOC 1000001 7 ESECEK EACAN 510 Adaptive Recognition Hungary VV ii CACCARI 1 O8101 510143 A properly set camera should provide a similar image A proper sample image 20 Proper character sizes in pixels on the sample image Page 11 14 Adaptive Recognition Hungary 7 Maintenance Storage The cameras are designed for 24 7 365 work under every weather condition and they do not need special maintenance Please keep clean the camera front
10. rklT Install Guide Page 8 14 5 Accessing the Camera Steps of accessing the web interface of the camera from a browser 1 Connect the camera to a computer or network switch then power on the camera After it is turned on both status LEDs red and green on the camera front are turned on while the camera is booting After finished the green status LED flashes two times signaling that the camera is ready for operation m We 6 2 Enter an alternate IP address in the 192 0 2 x subnet where x is an integer number between 1 and 254 except 3 with the subnet mask of 255 255 255 0 For more information see Appendix General If this computer is used on more than one network enter the alter settings below A Automatic private IP address User configured IP address 192 0 2 5 Subnet mask 955 255 9355 2 3 Use the ping command to test the communication with the camera Windows Linux C gt ping t 192 0 2 3 username mylinux ping 192 0 2 3 4 Soon the ping package returns Reply from 192 0 2 3 If not power off then on and enter the previous ping command again 5 Start a browser then enter the default IP address of the camera into the address bar http 192 0 2 3 After this the camera starts with administrator privileges ready to be set up and configured NOTE To enable all camera functions enable and update JavaScript and ActiveX controls in your browser 6 Co
11. rnate WINS server Figure 2 where Y is a free eth e g eth1 and 192 0 2 25 isasample IP address ParkIT Install Guide Page 13 14 Contact Information Should you have any problem during operating the ParkIT cameras our support team is at your disposal Please try to explain the problem as detailed as possible and do not forget to send the following information to make it easier to help you e The name of your company for administration purposes e The exact type of the product you have serial number is appreciated e Ifyou have problems during recognition send images in the original file format e f there is any error code or message appearing please send us the code snippet where it occurs a screenshot may also be helpful e If you noticed the problem while running a Demo or a sample application please let us know the name of the application you tested e Ifyou have some problem while developing your own application please specify the followings O O O O your programming language your operating system the name and version number of the compiler you use the programming technology e g native C C ActiveX NET If possible please send a short part of the source code Please try to determine the place where the error occurs e g the scapture getshutter command returns a negative number IMPORTANT NOTES e Before sending back a faulty device always contact ARH Support Team e Rep
12. ropriate screws for installation according to the mountable surface NOTE Failures due to inappropriate installation void the warranty 3 Setting up the Camera NOTE Technical specifications are subject to change without prior notice The camera is equipped with two cables The first cable is responsible for the power trigger and serial connections while the second cable is for communication via TCP IP The lengths of the pre assembled cables are 1 5 meters and they can be extended if necessary according to the followings gt RJ45 with e g inline coupler gt Power Trigger Serial with e g junction box IMPORTANT NOTICE For cabling use quality outdoor certified cables Improper cabling causes warranty to void Water may enter into the camera inside through loose cable ends Use smooth circular cables only 6 8mm diameter 3 1 Power Trigger Serial Connection Description Cable color 1 Se 1 2 pcucnacekevenatescescausieescsness Red c 2 GND irrasccccevcccsscevececevecnecsone Black a 3 Opto outG acess Red 4 Opto Out S esessssssesessseees Grey 5 Opto in S neeesser Brown 6 Opto in G wees Orange 7 NC no connect uu Yellow 8 Serial RX nesesssessessesseressssesses Green 9 Serial TX eeesssessessesserssssessees White 10 Serial GND wees Blue For trigger input For trigger output General purpose serial port IMPORTANT SEAL THE UNUSED CABLE ENDINGS END SL
13. tion between this equipment and the radio television receiver e Connect the equipment into a different outlet so that the equipment and the radio television receiver are on different power mains branch circuits e Consult a distributor of ARH Inc or an experienced radio television technician for additional suggestions Declaration of ROHS Compliance for Electrical and Electronic Products ARH Inc the Company hereby declares that the ParkIT ANPR camera family placed on the European Community market by the Company after 1st July 2006 are compliant with EC Directive 2002 95 EC on the Restrict of Certain Hazardous Substances in Electrical and Electronic Equipment commonly known as the EU RoHS Directive Compliance with RoHS means that where the product falls under the scope of the EU RoHS Directive the product does not contain the following substances Mercury Hg 0 1 Lead Pb 0 1 Cadmium Cd 0 01 Hexavalent Chromium Cr 6 0 1 Polybrominated Biphenyls PBB 0 1 Polybrominated Diphenyl Ethers PBDE 0 1 above the indicated maximum concentration values by weight in homogeneous materials unless the substance is subject to an exemption specified in the Directive or in subsequent Commission Decisions This declaration represents the Company s best knowledge which is partially based on information provided by third party suppliers Equipment modifications This equipment must be installed and used according wit
Download Pdf Manuals
Related Search