User Instruction Manual
Contents
1. The Alarm Dial 5 is switched to position 0 to switch off the alarm completely 3 Place the Bellman Alarm Clock upright on a level surface The Alarm Clock is usually placed near the bed but it can also be placed somewhere else where it can easily be seen and heard You can also easily take your Alarm Clock with you wherever you go s a 11 1 0 oi Sis f Z9 3 D 8 a2 7 9 Pe Technical information Power supply Mains power 7 5 V DC 1500 mA with power supply unit BE9216 Europe and BE9217 United Kingdom Battery power Internal NiMh type back up battery The internal back up battery must be changed at a service workshop Charging Via the power supply unit The discharged a a battery will take at least 24 hours to charge Activation Alarm call Built in clock alarm call function Analogue telephone network 26 120 V RMS 15 100 Hz External trigger 3 5 mm stereo mono provides a connection jack plug Connection between the inner and outer pins of the mono type 3 5 mm jack plug or between the middle inner and outer pins of the stereo type 3 5 mm jack plug see diagram DC 2 to 30 V between the inner pin and middle pin on the stereo type 3 5 mm jack plug see diagram AC 3 to 24 V RMS 5 150 Hz between the inner pin and middle pin on the stereo type 3 5 mm jack plug see diagram Output signals Built in sound signal 80 dBA maximum at 1 metre with a main frequency range of 5002. o Flashing with the flashing lights 17 on the front provided that the Flash Switch 9 is in the ON osition o Tmi a sound signal provided that the sound switch 7 is in the ON position o A BE1270 Bellman Bed shaker accessory will vibrate if connected Two tests are required to carry out a full test of the external trigger one to test contact and another to test voltage For further information see Activation Please note that when the Snooze Button 4 is pressed during an alarm from an external trigger any further alarm via the external trigger will be ignored for 45 seconds e Connect the alarm unit to the external trigger input 13 e Activate the alarm e The Bellman Alarm Clock will give the Mbllowing indications o Flashing with the flashing lights 17 on the front provided that the Flash Switch 9 is in the ON osition o Emitting the sound signal selected via the external trigger signal switch 8 provided that the Sound Switch 7 is in the ON position o Ifthe BE1270 Bellman Bed Shaker accessory is connected it will vibrate in the way selected via the external trigger signal switch 13 To test the builtin telephone connection e Connect input 15 on the Bellman Alarm Clock to an analogue telephone socket using a BE9105 telephone flex accessory and an adapter plug accessory e Ring the telephone number e The Bellman Alarm Clock will give the Kbllowing indications o Flashing with the flashing lights 17
3. 1000 Hz Built in flash light signal Approx 10 Candela Warning Flashes can cause epileptic attacks Vibrator power 2 0 4 0 V DC Additional information For indoor use onl Storlek W x H x D 110 x 130 x 92 mm Weight 460 g Colour White with red base and red buttons dials Flex length Power supply unit 1 8 m Accessories Bellman Bed Vibrator BE1270 Bellman External Trigger Cable BE9086 Bellman Telephone Flex BE9105 Adapter plug for the appropriate country Page 148 Be1341 Technical Solutions Function General The BE 1341 Bellman Alarm Clock is an Alarm Clock for indoor use which attracts the attention of the user using sound and light signals and also vibration if a BE1270 Bellman Bed shaker accessory is connected It is activated by the clock s alarm by connection to an external trigger input 13 or via direct connection to a telephone socket 15 Clock The Bellman Alarm Clock will indicate an alarm call via sound flash and vibration for up to 15 minutes unless the alarm is turned off or onto snooze The sound ranges across several frequencies and increases in volume to attract attention better Setting the current time Set the correct time with the Time Setting Knob 11 Setting an alarm call Turn the Alarm Pointer anticlockwise to the desired call time using the Alarm Call Knob 10 Activate the alarm by turning the Alarm Dial 5 to position 1 If the power supply unit is connect
4. Technical Solutions Be1341 Page 147 Bellman Alarm Clock Be1341 Thank you for choosing products from Bellman amp Symfon Bellman amp Symfon AB have both separate products and also complete systems geared to helping people with impaired hearing An example of this is the Bellman Visit 868 System which consists of a number of radio transmitters and receivers The transmitters detect different events in the surrounding area and transmit a radio signal to the receivers The receivers pick up this signal and provide indications using light sound and or vibration Read through the entire user manual first and then start to use the products Getting started Unpacking installing and testing the unit 1 Connect the power supply unit to the socket 12 The Bellman Alarm Clock must be connected to mains power for at least 24 hours in order to operate correctly Set the correct time with the Time Setting Knob 11 2 Switch on the alarm with the Alarm Dial 5 by turning it to position 1 Turn the alarm pointer anticlockwise using the Alarm Call Knob 10 until the alarm on the clock is activated The Bellman Alarm Clock will then emit sound and light signals and ifa BE1270 Bellman Bed shaker accessory is connected it will vibrate Press the Snooze Button 4 The background light on the clock face will come on at the same time as the alarm is switched off The snooze function delays the alarm call for approximately 3 5 minutes
5. ed the LEDs in the Snooze Button 4 will light up Snooze function The snooze button lights when the alarm is activated and blinks when the snooze function is activated To conserve the built in back up battery the snooze button will not light or blink when the external power supply is disconnected e g during a power failure The snooze function on the alarm delays the alarm call for approximately 3 5 minutes by pressing the Snooze Button 4 During this time the LEDs in the Snooze Button 4 will blink Switching off the alarm call The alarm is switched off completely by switching the Alarm Dial 5 to position 0 Illumination of the clock face The clock Mce s background light will come on when the alarm clock sounds or the snooze button 4 is pressed Telephone connection The telephone is connected via the Telephone Input 15 Use the BE9105 Telephone Flex accessory and an adapter plug accessory During activation via the telephone connection 15 further activations can be ignored for 45 seconds if the Snooze Button 4 is pressed External trigger It is possible to connect the vibrator output on several oMBellman amp Symbbn AB s products or other equipment that produces a contact or voltage to an external trigger 13 for activation In this way the Bellman Alarm Clock can be made to work as alarm equipment e g for an existing fire alarm During activation via the External Trigger 13 further act
6. ger can be altered using the switches 8 see figure below DIP switch LED pattern Vibration Flash settings Up Down Not Used Green is constantly 1 x ding dong low Separate lit frequency tone Green blinks 2 x ding dong Separate constantly high frequency tone Y Yellow is constantly 1 x ring low Ye lit frequency tone Yellow blinks 2 x ring ring high Yes constantly frequency tone Orange blinks Baby Rapid Yes constantly Yes Orange blinks Baby Rapid constantly Red and Orange VMA constant Long constantly blink alternately Red blinks Fire alarm constant Long constantly Page 152 Be1341 Technical Solutions Testing It is easy to test the Bellman Alarm Clock BE1341 If the Alarm Clock does not work as described below you can check further under Troubleshooting guide How to test The BE1341 Bellman Alarm Clock should always be connected to the electric socket with the enclosed power supply unit To test the flashing light sound and vibration with the BE1270 Bellman Bed shaker accessory e Switch on the alarm with the Alarm Dial 5 by turning it to position 1 e Turn the Alarm Pointer anticlockwise using the Alarm Call Knob 10 until the alarm on the clock is activated e The Bellman Alarm Clock will give the Mbllowing indications o Switching on clock face background illumination 3
7. ivations can be disregarded for 45 seconds if the Snooze Button 4 is pressed Technical Solutions Be1341 Page 149 Indicators and Signals Sound The Bellman Alarm Clock sounds an alarm The sound volume is 80 dBA maximum at 1 metre The main frequency range is 500 1000 Hz Ljudet kan st ngas av med Ljudomkopplaren 7 Flashing light When the Bellman Alarm Clock is activated 4 built in flashing lights 17 flash with a bright white light The flashing light can be switched off via the Flash Switch 9 Vibration The Bellman Alarm Clock can power two BE1270 Bellman Bed shakers accessory which are placed under the pillow to wake the user up when the Bellman Alarm Clock is activated The Bed shaker is connected to the sockets 14 Power supply The LED 1 is constantly green when the power supply unit is connected correctly When the LED 1 blinks green the internal back up battery is charged but the Alarm Clock has no external power supply either because of a power failure or because the power supply unit is not connected When the LED 1 blinks yellow the back up battery is nearly flat and the Alarm Clock has no external power supply either because of a power failure or because the power supply unit is not connected The battery must be charged by connecting the power supply unit and allowing the Alarm Clock to charge for at least 24 hours Troubleshooting in brief Nothing happens e Check that the power su
8. on the front provided that the Flash Switch 9 is in the ON osition a Emitting a ring type sound signal provided that the Sound Switch 7 is in the ON position o The BE1270 Bellman Bed Vibrator accessory will vibrate if connected Trouble shooting You can carry out a number of checks yourself before sending a product for repair Troubleshooting guide Nothing happens e Check that the power supply unit is connected correctly The LED 1 blinks Check that the power supply unit is connected correctly The LEDs in the Snooze Button 4 do not come on Check that the power supply unit is connected when the alarm clock is switched on correctly The Alarm Clock does not emit any sound signals Check that the Sound Switch 7 is in the ON position The Alarm Clock does not emit any Mash signals Check that the Flash Switch 9 is in the ON position
9. pply unit is connected correctly and that the LED 1 is constantly green The LED 1 blinks e Check that the power supply unit is connected correctly The LEDs in the Snooze Button 4 do not come on e Check that the power supply unit is connected when the alarm clock is switched on correctly The Alarm Clock does not emit any sound signals e Check that the Sound Switch 7 is in the ON position The Alarm Clock does not emit any Mash signals e Check that the Flash Switch 9 is in the ON position Page 150 Be1341 Technical Solutions off on ext trig AO oly 1234 1 Power supply LED 11 Time setting knob 2 Alarm pointer 12 Input for power supply unit 3 Illuminated clock face 13 External trigger input 4 Illuminated snooze button 14 Vibrator output 5 Alarm dial 15 Analogue telephone input 6 Base 16 Programming switch 7 Sound switch 17 Flashing lights 8 Signal switches for external trigger 9 Flash switch 10 Alarm call knob Technical Solutions Be1341 Page151 Appendix Further information Further information Adjustments No adjustments apart from setting the time and selecting the call time are required for normal use The relevant descriptions are provided below if you wish to change a setting for some reason Signal pattern on external trigger The signal type set during external activation and indicators and signals activated by an external trig
Download Pdf Manuals
Related Search