OIL-INJECTEDROTARY SCREW COMPRESSORS
Contents
1. 29 CAP 876 REV April 2014 D Storage In some cases it may be necessary to store the compressor for extended periods of several months before placing the unit in operation When this is required do the following 1 Cover and seal all machine openings to prevent the entrance of water and dirt 2 If the storage conditions are below freezing drain off the after cooler traps water cooled heat exchangers and attendant piping Outdoor storage is not recommended 30 5 5 JIM BABA Said LIL JIM JM 5 0 181101811 Jie 3e ut JIM noH 0008 10 1 1844 10 34 NOH 0007 18714 110 JIU Jy INOH 0009 pue 0000 T eoi ues E Q suonepueuuuooe pue uoneuuojur eJoui Ao quistp e Si 3400 83 pezuotgne INCA puepuejs uou jo KouenbeJ sjueuuoJiue pue uonipuoo jeuuou pequosep lt Jo Aesseoeu se eoe deM p Jo Anfu 5 esneo jnseJ pue AJUBLEM juoneredo Jas 511 upes eA e Asjes jou og 6 ebeduo ees Huljeredo snsJe aji 10 402. o c i un Section 6 0 31 CAP 876 REV H April 2014 6 2 Air Filter The air filter is the primary protection for the compressor from harmful dirt being ingested into the oil system It needs to be inspected weekly for clogging or holes The period for these inspections is dependent on the environment the machine is in Filter should be replaced at 6months or 2000 hours Element Inspection and Replacement 1 Switch off the unit disconnect the power and lockout and tagout to prevent accidental starting 2 Allow one minute after stopping for the system to settle and the pressure to be relieved 3 Loosen the wing nut that secures the cover and remove the cover 4 Loosen the wing nut that secures the element and remove the element 5 Place a bright light inside the element to inspect for damage or holes Discard any element that has a hole 6 Inspect all gaskets and gasket contact surfaces of the housing Replace any gaskets that are or broken 7 Clean the housing with a damp cloth Do not attempt to blow out dirt with compressed air 8 Place a new element in the housing and re secure in place with the wing nut 9 Replace the cover and tighten the wing nut 10 Reset the filter service advisory in the controller and the machine will be ready for operation 6 3 Oil Filter The oil filter in the compressor system is a full flow replaceable canister type The filter should be replaced every
3. 1 Shutdown the compressor if abnormal noise or vibration is observed 2 Do not loosen any screws or open any control valves during operation Warning Failure to do so may cause injury 3 Make sure to drain condensed water in after cooler and water separator 4 Record voltage current discharge pressure discharge temperature and oil level Inspect gauges periodically during operation for future reference 5 For extreme environment application FSCURTIS controllers are equipped with a Frost Protection function to prevent lubricant from coagulation Please refer to controller manual page 21 for detail setting Setting the compressor delivered pressure Observe all safety precautions and follow all safety guidelines when performing service to your air compressor To change the pressure the compressor delivers requires five steps These must be done in the following sequence These first 4 steps are done on the ABB Drive keypad 1 Unlock the parameters 2 Change the Internal Setpoint pressure on the drive key pad for the desired operating pressure 3 Change the drive set Frequency to match the operating pressure in step one 4 Lockthe parameters The last 3 steps are done on the AIMS Plus controller on the front of the machine 5 Change the System Safety pressure to protect against high sump pressure 6 Change the Cut Out Unload pressure set point 7 Change the Cut In Load pressure set point ABB Drive Key Pad STEP 1 Unlock the p
4. April 2014 F Control system and electrical circuit 1 Control system a Motor startup The intake valve gradually opens with motor startup because of the vacuum inside the compressor inlet Oil circulating to lubricate the compression chamber and the bearing is assured by the pressure difference between the vacuum and atmosphere b Motor operation After motor startup system pressure gradually increases until the compressor is running at full load intake valve stays fully opened Air is then delivered through the minimum pressure valve to the end user when pressure is at least 65 3 psi c Full off load operation When the system pressure reaches the upper limit of the settings the intake valve closes and the air oil separator vessel relieves the air to ambient Compressor is then running off load When system pressure reaches the lower limit of the setting the intake valve opens and relief stops The unit is then on load d Stop Pressing the OFF button See Aims controller manual will close the intake valve and relive pressure in the air circuit When pressure in the air oil separator vessel reduces to a preset value a timer will countdown and if no air is needed then the motor will stop shutdown e Emergency stop When the emergency stop is activated the main power supply will be shutdown with a warning shown on the control panel Motor will stop immediately air circuit pressure will be relieved and the intake valve will clos
5. 4000 hours of operation This element protects the compressor bearings from grit and dirt ingression throughout the system A dirty filter will cause an oil flow restriction that can result in high oil temperature and a unit shutdown A DANGER Hot oil under pressure will cause severe injury death or property damage Be sure the compressor is shutdown and pressure relieved before attempting to remove the oil filter separator oil fill or changing the oil Oil Filter Replacement 30s CAP 876 REV April 2014 Switch off the unit disconnect the power and lockout and tagout to prevent accidental starting Allow one minute after stopping for the system to settle and the pressure to be relieved Using a strap wrench remove the old element and gasket Clean the gasket surface with a clean rag Apply a light film of oil to the new gasket Hand tighten the new element until the new gasket is seated in the gasket groove Continue tightening by hand an additional 12 to turn Reconnect power and reset filter service advisory Restart the machine to check for leaks OONO BIN 6 4 Air Oil Separator The air oil separator should be changed every 8000 hour once a year when there is excessive oil vapor in the discharge air or as indicated by a maintenance indicator whichever occurs first Higher temperature operation can cause the element to plug faster Consistent operation in temperatures over 104 F will r
6. 6 0 Maintenant do ehe due edo iid t ce ED dan E ane Maintenance Air Filter aana nana aana nana Air Oil Separator cer cake DEO UNG MM T ASE Thermostatic amp Minimum Pressure ect Maes eee ta eae DR LL 8 Air End Motor 7 0 Trouble ShoOllhg uo Monit aa en GE Na beat De oe 8 0 Mice ane cs 876 REV H April 2014 CAP 876 REVH April 2014 Chapter 1 0 Introduction A Preface Warning Read this manual before installation and operation Become familiar with this manual its safety instructions and its operation before beginning any work Serious personal injury may result if safety or operational information is not understood Alert signals Description of signals gt Danger Danger is used to indicate presence of a hazard that will cause severe personal injury or death or substantial property damage gt Warning Warning is used to indicate the presence of a hazard which can cause sev
7. oil line Plugged oil return line Operating below rated pressure Damaged or dirty separator Lightly loaded or excessive load unload cycles Using incorrect oil High Temperature Shutdown Elevated ambient temperature Low sump oil level Plugged oil filter Restricted cooling airflow Clogged heat exchanger Thermal bypass is leaking Faulty high air temperature switch Delivery pressure set too high Panels are open Exhaust air is restricted High power consumption mpo cooocop Plugged separator Plugged aftercooler Improper air pressure switch setting Too low of a line voltage Electrical phase imbalance Imminent motor failure Imminent air end failure Loose electrical connection Belt slippage Safety valve discharges om Over pressure switch not set correctly Inlet valve not closing properly in relation to air demand Plugged separator Faulty minimum pressure check valve Faulty safety valve Incorrect set point on safety valve Section 8 0 Maintenance Log Model Serial Number Changed Greased Checked Date Hour meter Air oil Motor Cleaned Fitting Reading Filter Filter Oil Separator Bearings Cooler Tightness 42 CURTIS curtis toledo inc 1905 Kienlen Avenue St Louis Missou
8. 30 F 18 CAP 876 REV April 2014 Temperatures above this will cause the compressor to shutdown 4 Control principle for frequency speed controlled air compressors The control logic of conventional fixed speed compressors is shown in fig 4 1 For example the current enters the 2 pole motor with 60Hz thus the theoretical rotation speed of motor output is 3600rpm The required rotation speed can be achieved by adjusting a pulley or gear ratio However the speed is still a fixed value When the demand of compressed air at the end user decreases the amount expelled cannot be reduced by adjusting the rotation speed of the machine itself Therefore in most fixed speed compressors valves such as a suction valve must be introduced to control the amount of air sucked in On the other hand the frequency controlled GSV Series compressor has an inverter installed near the motor which is used to adjust the rotation speed of the motor as demanded Current frequency GOHz Frequency Converter Frequency Converter Fixed frequency 112 1 2 machine type e Motor Rotation Speed 60 7200 RPM Fig 4 1 Besides the variable speed inverter another characteristic of the GSV Series speed controlled air compressor is a stable and accurate feedback control system Its basic control flow is shown in fig 4 2 When the pressure transducer delivers the pressure value P ne in the system into t
9. 4 suomipuoo Buiuuni pue jueuuojiAue uo Duipuedep juenbey ambal Aew y 0008 apun Ji Auead 18429394 Jembar Mojo juo y oog enu 1 0009 054 asp 9LZO9A Atsdsz L g 00L6 NS5 Asdsz L g 00L6 NS5 JM 991195 29 5405170 00 5 69 JnoH 0008 vVISCOG 1 8 00 9 9 JIM eoe 60299A 001 87 ASD poe 001 52 ASD 991 195 JnoH 0007 DEINES 60239A 001 54 ASD 1noH 0002 Buijdnos eAup 29950 sped uomneJgi nue joodsu uojeouqn Buueeq 100 104 0 0 0 I 9 Jo suis Jo sesou joedsu SJeuojsej pue suy 9500 Jo s ojeipei jo uesjyjjedsu 5 pued uesjonoedsu uonons duns ejesuepuoo Uotge1edo 10 jaro aunsseJd 19 I9291 WOJ ojesuapuoo Bul 2 0 Y02949 pue juod Bulyesado eJnsseJd JI JI 0 duns 49249 ALO Maintenance 000 vc 000 000 02 000 9L 000 25 sd INGSHOS SONVNALNIVW du 00 du 92 samas ASS 9 8 4 2 D 6 2 m
10. CAP 876 REV H April 2014 cuRTIS eries OIL INJECTED ROTARY SCREW COMPRESSORS OPERATOR MANUAL cn m ET Ei i ant 222 Ld GSV 75 GSV 100 Personal injury and or equipment damage will result by failing to pay attention to the vital safety information and instructions in this manual Carefully read understand and retain all safety information and instructions before operating this compressor Table of Contents 3 0 Principle of Screw Air CIC aa aa ai No tcm a a na E A b a aa d Ga E a a GG a aa BN 4 0 System Flow Chart and Components System Flow ost enn er Dedi ieu queo aaa gt Description se eerte ettet EE GSV 75 100 Specifications Protection Warning Le pq etr veia ein Ra eg Control Systems Electrical 5 ais ono doo ado tec daa ente dos ed ete a pace dette LUND ca on de OR choad fs DAR E eR COD RATE Lr a cli me TT kaa Setting Delivered Pressure 2 1 1 1111 11 SC 2100 Controler ed a Jenne a ap aa aaa lt Storage HR
11. IT key to change the maximum Frequency Using the UP or DOWN arrow button set your required frequency from the chart below Once the frequency is selected press SAVE key amp then press EXIT key once FD SET FD SET UNIT FREQUENCY UNIT FREQUENCY MAX MIN Hz MAX MIN Hz 100PSI 95 35 100PSI 140 35 GSV 20 125 81 89 35 GSV 50 125PSI 132 35 150PSI 79 35 150PSI 120 35 100PSI 120 35 100PSI 86 28 GSV 25 125PSI 112 35 GSV 75 125PSI 83 28 150PSI 101 35 150PSI 72 28 100PSI 140 35 100PSI 120 25 GSV 30 125PSI 131 35 GSV 100 125PSI 108 25 150PSI 123 35 150PSI 99 25 100PSI 112 35 GSV 40 125PSI 106 35 150PSI 96 35 NOTE Minimum frequency does need to be changed STEP 4 Lock the parameters 3 1 Using the DOWN arrow key to scroll to Group 16 press the SELECT key and scroll DOWN to Parameter 1603 Press the EDIT key Using the UP arrow button set passcode 358 press the SAVE key 2 Using the UP arrow key to scroll to Parameter 1602 press the EDIT key and scroll UP changing condition from OPEN to LOCKED Press the SAVE key Press the EXIT key three times to return to display showing Hz Amps and pressure 27 CAP 876 REV H April 2014 AIMS SC 2100 Controller STEP 5 Change the Pressure Frequency and Target Pressure The following instructions are available in the AIMS SC 2100 Controller for GS CAP830 1 On the mai
12. Place a spill pan under the valve Allow one minute after stopping the compressor for settling and the pressure to relieve Remove the cap at the top of the valve It is spring loaded so be careful that it does not fly off Remove piston and seat Inspect the valve body for scratches and deterioration of the seating surfaces Replace old parts with replacement parts and re assemble the valve If you loosened the fill plug to insure pressure relief replace it and tighten Return the unit to service 6 8 Fan Check the fan for cracking loose rivets and bent or loose blades Make sure that it is securely mounted and tighten the mounting screws if loose Replace a damaged fan immediately In case of high discharge temperature inspect the cleanliness of the cooler and clean 362 CAP 876 REV H April 2014 accordingly Cleaning instructions Loosen the screws and remove the fan cover Use an air sprayer from top to the bottom to blow dust away as the figure below 6 9 Motor The motors on the air compressor require routine attention too Every 1000 hours of operation or three months whichever comes first check that the motor is clean and ventilation openings are clear The second area to maintain to insure long motor life is bearing lubrication Bearing grease will lose its lubricating ability over time not suddenly The type of grease used the temperature of operation and the s
13. arameters 1 From the main screen on the drive keypad displaying Hz Current and Pressure press the arrow button under Menu After pressing Menu the screen will display PARAMETERS 2 With the PARAMETERS highlighted press ENTER key 3 Using the DOWN arrow key to scroll to Group 16 System Controls press the SEL key and scroll down to Parameter 1603 Pass Code Press the EDIT key Using the UP arrow button set pass code 358 hold UP button till 300 displayed wait for 2 sec till cursor switches to tens amp enter 5 wait 2 sec till cursor switches units amp enter 8 press the SAVE key 4 Using the UP arrow key to scroll to Parameter 1602 Parameter Lock press the EDIT key and scroll UP changing condition from LOCKED to OPEN Press the SAVE key Press the EXIT key once 26 CAP 876 REV April 2014 STEP 2 Change the Reference Frequency 1 Using the DOWN arrow key to scroll to Group 11 press the SELECT key and scroll down to Parameter 1104 Minimum Freq 1105 Maximum Freq Press the EDIT key to change the maximum Frequency Using the UP or DOWN arrow button set your required frequency from the chart below Once the frequency is selected press SAVE key amp then press EXIT key once STEP 3 Change the Frequency 2 Using the DOWN arrow key to scroll to Group 20 Limits press the SELECT key and scroll down to Parameter 2007 Minimum Freq and 2008 Maximum Freq Press the ED
14. ase in decibel level If sound transmission is important install a sheet of rubber or cork beneath the compressor to reduce noise Flexible piping may be required It is recommended that there be at least 38 of clearance between top of compressor and overhead air duct installation for better cooling effect on air cooled compressors Mounting nuts on air inlet and outlet are prefabricated on cabinet Remove the 4 bolts and red blocks that secure the air end motor sub frame for shipment to Mounting bolt Red block CAP 876 REV H April 2014 GSV 75 100 Compressor Outline Drawing Specification Vent Cover Assembling Hole Air Outlet Pipe Power Wire Inlet Hole Controller Rubber Pad Water Drain Hole 2 PF 1 4 Oil Drain Hole PF 1 2 GSV 75 100 Drawing _____________ Released csv 7s 100 jem 191 A CAP 876 REV April 2014 Recommendations amp Precautions for Air Piping and Cooling System 1 Air Piping 1 Install required accessories 2 Main piping should have 1 2 slant away from the compressor to drain the condensate 3 Pressure drop of piping must not exceed 5 of discharge pressure Select larger piping than required for better efficiency 4 Branch line must be locat
15. e hs um ux tx i _To JP4 7 5549 4 gt v 2 gt p Qu gt 2 lt 9258 Hr 5 gt 24V lt 10 11 a EN gt gt 2 R 2 o if 26 b DINIS gt 406 4 R0125 12 X 2m DRIVE FAULT RELAY DCOM DQ 5 z m 3 5 ROLK26 F o Ek 2 gt J 1 012 9 z 9 N N N N 13 CAP 876 REV April 2014 Section 3 0 General Description COMPRESSOR The compressor assembly is an oil flooded positive displacement single stage helical screw type unit consisting of two rotors or screws supported axially by roller bearings and enclosed in a housing or stator as depicted in the sectional view Figure 3 1 Figure 3 1 Compressor Assembly The compression cycle as depicted below Ref Figure 3 2 has air entering the compressor through the inlet port that becomes trapped between the helical lobes of the main rotor and the matching grooves of the secondary rotor A As the rotors turn air is trapped in the cavity created by the mashing lobe and groove and reduced in volume or compressed It is then pushed through the successive cavities B until it reaches the discharge end
16. e to mix hot and cold oil lt will begin to open at 149 F and be full open at 168 8 F This insures that the system temperature is above the pressure condensation point and there is minimal accumulation of water To repair this valve 1 gre IN Switch off the unit disconnect the power lockout and tagout to prevent accidental starting Allow one minute after stopping the compressor for settling and the pressure to relieve Place a spill pan under the valve filter assembly Remove the retaining cap from the valve block Remove the cap and the internal parts Take care to note the orientation of the spring piston and element Reassemble with replacement parts Loosen the fill cap and then tighten it after replacing any volume of oil lost with fresh oil Return unit to service 6 7 Minimum Pressure Valve The minimum pressure valve is non adjustable spring biased check valve It has been designed to maintain a minimum sump pressure of 4 5 bar If the pressure is allowed to get too low the oil carryover rate will increase and the separator could be damaged Air exiting the vent hole in the cap of the valve indicates an o ring failure and it needs to be replaced The air leaking into the spring cavity where the vent is located will change the operation of the valve To repair this valve l HO NAN Switch off the unit disconnect the power and lockout and tagout to prevent accidental starting
17. e to prevent lubricant from coming out of the air end Only use the emergency stop button in a hazardous situation f Auto stop with time lag If compressed air is not required the compressor runs at off load until it is stopped after a set time lag If compressed air is required the compressor runs at full load to meet the demand The amount of possible auto stops is limited to five times each hour Since there is no warning on the panel for an auto stop be careful using this function Frequent starting and stopping of the motor will result in motor damage 24 CAP 876 REV April 2014 Section 5 0 Operating Procedure A Testrun startup and shutdown 1 2 Connect power and grounding cables and check power supply Check oil level Please refer to the description on air oil separator vessel from Chapter 4 2 If the initial startup is several months after delivery add 0 5 Liter of CurtisLubePlus FSC 8000 lubricant through intake valve and rotate air end manually to prevent compressor damage from lack of oil Check cooling system Check Rotation Press the Emergency Stop button within a few seconds after startup and identify the direction of the airend and fan motor rotation refer to figure 5 1 If the motor rotation is incorrect for units equipped with a variable speed drive switch any 2 of the 3 power cables on the bottom of the drive If Fan rotation is incorrect switch any 2 of the 3 power cables on the incoming power
18. ed at the topside of main piping to avoid condensate from flowing into the facilities To prolong service life of pneumatic tools install an air filter regulator unit on the outlet Do not randomly reduce the size of the main piping If necessary use the proper reducer or a large pressure loss may incur The common installation arrangement is air compressor air tank dryer An air tank is capable of draining some of the condensate and cooling down the temperature of compressed air This will lead to more efficient dryer operation 8 If the air requirement is large for a short period install a higher volume air tank to reduce the frequency of full off load control 9 The ideal piping main would be constructed around the factory as a loop for delivering compressed air from both sides at any point 7 5 6 7 7 2 Cooling System Install the air cooled compressor in a well ventilated area to avoid high temperature shutdown If the unit is in a sealed room ventilation is required and its capacity must be larger than the cooling fan in the compressor In accordance with Figure 2 1 please select proper ventilating equipment for use Figure 2 1 Heatin Volume of Ventilating Volume of Model 9 Ventilating Fan Compressor Room HP Btu cim cim GSV 75 75 225400 7600 gt 12000 GSV 100 100 307500 7600 212000 Remarks The above data is compressor room temperature rise according t
19. emperature switch open due to restricted oil flow Loose or missing electrical components Pressure switch set too high Motor overloads tripped out Low voltage the desired pressure Compressor does not build up to Ooc oococp Inlet valve partially closed Belt slippage Restricted inlet air cleaner Excessive air demand Defective pressure gauge Pressure switch set too low Excessive pressure drop across the separator element Solenoid valve stuck open Air end malfunction excessive clearance or rotor movement Compressor sized too small Safety valve keeps discharging Compressor will not load a b o Pressure switch set too low Inlet valve not opened Faulty solenoid valve 41 Capacity delivery is below stated amount Restricted inlet air filter Inlet valve partially closed Air pressure set too high Insufficient oil flow Leakage in air system Worn air end Lower frequency and lower motor speed Belt slippage Solenoid valve malfunction Compressor surges 2o Erratic air demand Customer air system too small for demands Faulty minimum pressure valve Pressure switch differential too low for the system conditions Faulty pressure transducer Faulty pressure relief valve Faulty solenoid valve Faulty pressure relief valve Excessive Oil Consumption 7 ooocp Overfilled sump Broken
20. enance Compressor Is controlled by PID see above and may start automatically according to the setting Relief valve is necessary for air piping larger than 1 2 not exceed the rated discharge pressure on nameplate during operation The enclosure should be in place prior to operation CAP 876 REV April 2014 Section 2 0 Receiving and Installation A Receiving 1 2 3 Check your order to ensure it is correct Check if the machine or any accessories received any damage during shipment Upon receiving this machine please read this manual thoroughly and any supplements related to the equipment you purchased before attempting to install or operate the compressor B Installation In order to ensure proper installation and trouble free operation 1 2 3 The compressor should be installed on any level surface capable of supporting its weight Lift the compressor using the area under the base frame Make sure the lift equipment has enough capacity and complies with local regulation Select a location that is dry well ventilated and where the atmosphere is as clean as possible The area should be free of dust chemicals metal filings paint fumes and overspray The ambient temperature should be kept below 104 F and above 32 F See general arrangement drawing for minimum space requirements for normal operation and maintenance Hard surfaces may reflect noise with an apparent incre
21. equire more frequent separator element changes A DANGER Hot oil under pressure will cause severe injury death or property damage Be sure the compressor is shutdown and pressure relieved before attempting to remove the oil filter separator oil fill or changi the oil Separator Element Replacement 1 Switch off the unit disconnect the power and lockout and tagout to prevent accidental starting 2 Allow one minute after stopping for the system to settle and the pressure to be relieved Loosen the air pipe from min pressure valve control air pipe from intake valve and oil pipe from special joint close to air end Loosen 10 bolts for fastening air oil cover Loosen oil return pipe and inspect for clogging Apply the new one inside the air oil receiver and inverse step 5 3 Reconnect power and reset separator service advisory Restart the machine to check for leaks e par eere 7222 6 5 Lubricant CAP 876 REV April 2014 Your compressor has been filled and tested with a high quality synthetic compressor lubricant It has the advantage of extended service life high temperature operation and easy start up when cold reduced sludge and lacquer buildup and is completely compatible with all seals gaskets and other compressor materials When operating in severe conditions it will be necessary to change the lubricant more frequently Temperature of operation has the most significant effect on the l
22. ere personal injury or substantial property damage gt Caution Caution is used to indicate the presence of a hazard which can cause personal injury or property damage m Reference Supplementary instruction for operation and maintenance CAP 876 REVH April 2014 Illustration of symbols Prohibited N Extreme caution Warning Labels are placed on the machines If the labels are not clear or missing please contact MANUFACTURER directly Explanations of safety symbols Operation manual r CAUTION READ AND UNDERSTAND THE INSTRUCTION MANUAL BEFORE INSTALLING AND DPERATING THIS UNIT FAILURE FOLLOW THE OPERATION AND MAINTENANCE PROCEDURES COULD RESULT SEVERE INJURY OR DAMAGE ONLY QUALIFIED PERSONNEL SHOULD OPERATE OR MAINTAIN THIS ROTARY SCREW COMPRESSOR BABS4S Follow the instructions before use of this compressor Confirm the direction of rotation before startup To restart compressor after inactivity of 6 months or Caution before longer rotate air end manually with the power off If start it is difficult to rotate please contact up MANUFACTURER directly CAP 876 REVH April 2014 Danger Electric circuits Danger Rotating parts Danger Hot or noxious gases outlet unbreathable Danger Heat Do not touch hot areas CAP 876 REVH April 2014 Rotation Read instructi
23. f the unit disconnect the power and lockout and tagout to prevent accidental restarting Re install the grease relief plug Return unit to service 38 6 10 AIR END MOTOR REMOVAL Air end motor removal and installation Note It is important to have clear access to the air end motor area Lifting devices are necessary for the removal and installation of the air end motor A Turn off compressor Switch off the unit disconnect the power and lockout and tagout to prevent accidental starting B Allow one minute after stopping the compressor for settling and the pressure to relieve Remove the left cover Remove the air filter hose from inlet valve body Remove air filter AP switch from intake valve Remove the 4 bolts from base of the inlet valve assembly and set the inlet valve assembly aside G Remove all air and oil line to the air end and inlet valve CAUTION Oil may leak from oil hoses when removed H Loosen the 4 bolts from the air discharge pipe and loosen the 4 bolts from the air receiver flange Remove the temperature probe from the discharge end of the air end CAUTION This is not a well type probe oil may run out of the air end J Loosen the 2 bolts from the air end bracket K Loosen the bolts from the coupling housing and the motor and then remove the 4 bolts connecting the coupling housing and the air end L Remove the air end from the cabinet M Loosen the bolt holding the coupling to the s
24. haft and remove the coupling with special tool Installation of the air end Reverse removal instructions For motor removal continue from step M N Remove cover from motor junction box O Note wire connections P Remove wires and conduit connectors from the motor junction box Q Remove the bolts from the coupling housing R Remove the 2 bolts from the motor bracket S Lift and remove motor from the cabinet To reinstall motor and air end start with step S and reverse procedure 39 SPACER SPIDER AIR END COUPLING MOTOR COUPLING COUPLING GUARD ADAPTOR NOTICE SLIDE AND FIRMLY PRESS SPACER AGAINST AIR END SLEEVE SLIDE AIR END COUPLING AGAINST SPACER AND HOLD IN PLACE WHILE TIGHTENING COUPLING SETSCREW IMPORTANT IT IS CRITICAL TO HAVE NO GAP BETWEEN AIR END SLEEVE SPACER AND AIR END COUPLING 40 Section 7 0 Troubleshooting Compressor will not start No power Fuses blown in the control circuit Heaters not installed in starter Motor overload latch not reset Loose or missing wires or components in the control circuit Low voltage e g using 230 volt in a 460 volt system Faulty temperature switch Suction valve not closed Pressure in oil separator tank Unit starts but shuts down immediately o Pressure switch or timer failure Incorrect heaters or adjusted too low in starter High Air T
25. he controller the controller passes the corresponding 4 20mA signal according to the pressure received to the inverter When the value of P net is lower than the set value P setting in the inverter this indicates that the air demand at end user is increasing and the inverter will adjust the rotation speed of the motor in order to increase the output of the air and achieve the set value of pressure not over the maximum set rotation speed for the air compressor Since the demand for compressed air at the end user will change variably according to the real process requirement the PID proportional integral and differential function of the inverter converts the amount of airflow required by controlling the motor speed in a real time and precise mode If it fails to perform calculations precisely the pressure set value P in the air receiver will change too rapidly to 19 CAP 876 REV April 2014 stabilize the setting pressure value P setting The variation of pressure on frequency control air compressors is within 1 4psi Compressor Pressure 100 psi Control Pressure 103 psi Rotation Speed Frequency Inverter AP PID Control Demand 40 P Proportional Integral D Differential Built in the frequency inverter Fig 4 2 20 CAP 876 REV H April 2014 5 GSV Series Screw Air Co
26. ife of the lubricant The following chart shows the decrease in interval based on temperature Figure 6 1 CurtisLubePlus FSC 8000 Oil Discharge Temperature Operating Hours 9 P Below 185 F 18510 194 F 194 to 203 F Intervals 8000 6000 4000 To eliminate confusion concerning what type of lubricant to use always use CurtisLubePlus If other lubricants are used failures due to lubrication are not FSC 8000 Lubricants warrantable and conditioners CAUTION Plugged filters coolers and orifices can result from mixing different lubricants This will also void the warranty Be sure to use only FS CURTIS Lubricants in refilling your compressor 34 CAP 876 REV April 2014 Oil Analysis Oil analysis is an excellent tool to add to your compressor maintenance program At regular intervals you can submit lubricant samples to a qualified laboratory From this you receive a detailed report showing the lubricant condition wear metals and contaminants The rate that these measurements change over time provides the basis for predictive compressor maintenance saving you from unplanned machine downtime and unnecessary oil changes A DANGER Hot oil under pressure will cause severe injury death or property damage Be sure the compressor is shutdown and pressure relieved before attempting to remove the oil filter separator oil fill or changing the oil Check
27. ing Oil Level and Adding Compressor Oil 1 Switch off the unit disconnect the power and lockout and tagout to prevent accidental restarting Allow one minute after stopping the compressor for settling and the pressure to relieve Remove any dirt from around the fill cap and then remove the fill cap Inspect the cap for damage and cleanliness Replace if necessary The oil level gauge should have the arrow in the green section of the gauge on the separator tank Replace the cap securely Never put the cap on without tightening it immediately D Changing Compressor Lubricant 1 Switch off the unit disconnect the power and lockout and tagout to prevent accidental restarting 2 Allow one minute after stopping the compressor for settling and the pressure to relieve Remove any dirt from around the fill cap and then remove the fill cap If the lubricant appears dirty or has a foul smell it should be replaced 4 Drain the lubricant from the bottom of the air oil receiver Oil will drain more quickly and completely if it is warm from operation Close all drains and replace with fresh compressor oil to the proper level Replace the fill cap and run the unit Check the oil level Please refer to the directions on oil receiver from Section 5 0 NO 35 CAP 876 REV April 2014 6 6 Thermostatic Valve The thermostatic valve is a non adjustable temperature control valve On the compressor we use this valv
28. is danger associated with operating this equipment Accidents are frequently caused by lack of familiarity or failure to pay attention Use this machine with extreme caution If normal safety precautions are overlooked or ignored serious personal injury may occur The following are some safety suggestions that users should be familiar with Caution Users who neglect these safety precautions run the risk of serious injury or death Keep fingers and clothing far away from rotating parts Compressed air from this machine cannot be used for pharmaceutical food breathing air or health requirements without further treatment Release all pressure from the system prior to maintenance Electric shock could be fatal Grounding of starter and motor is necessary Choose grounding cable according to the power range of the compressor Ground fan motor through starter Lockout and tagout power supply before working on control panel Lockout and tagout power supply before inspection and maintenance Compressor is controlled by PID proportional integral derivative controller and may start automatically according to the setting PID is a generic control loop feedback controller widely used in industrial control systems Warning Users who neglect the following instructions might damage the compressor Lockout and tagout the compressor if maintenance is needed Lockout and tagout power supply before inspection and maint
29. mpressor Specification 1 GSV 75 100 Moral GSV 75 GSV 100 2 psi 100 125 150 100 125 150 E CFM 353 332 299 474 430 390 C it 2 apan m min 10 5 9 9 8 9 14 1 12 8 11 6 gt V 2 F Ambient temperature 20 psi Setting pressure 200 psi 75 100 iid kW 55 75 Enclosure TEFC 2 rpm 828 2544 828 2455 828 2130 740 3550 740 3195 740 2929 Starter Inverter Voltage Volt 230 460 3PH Frequency Hz 25 120 Length in 93 9 c Widih in 47 6 E Height in 72 6 Weight Ibs 4000 Discharge outlet inch 2 PF 21 Capacity FAD measured in accordance with ISO 1217 Ed 3 Attachment C 1996 Ref condition Dry air suction pressure 1 bar Due to continuous product development at FSCURTIS design and specifications are subject to change without notice CAP 876 REV April 2014 E Protection and warning 1 Motor overload protection There are two motors in the compressor assembly One is the main drive motor and the other is the cooling fan motor Generally when running current that exceeds the upper limit of the relay the main power will shutdown automatically Re setting the unit is required prior to the next startup The relay limit has been preset by the factory To maintain normal operation please do not change the limit setting without consulting the factory 1 Human error such as adjusting to a higher discharge pressure or improper setting of the overload relay may cause a nui
30. n air compressor screen press the i SET key to enter the password screen Input Password 0000 The flashing bit is current input bit Press the UP key to increase one input bit and the DOWN key to decrease one input bit Move the flashing bit by pressing the SHIFT ENTER key After the input is finished press the i key Input user password 1111 and press i key to enter the user parameter set screen Oper Svc Time When the symbol is moved to the Oper press the SHIFT ENTER key to enter the operating parameters set screen Unload P 125psi Load 105 Press SHIFT ENTER key UP DOWN keys for set Unload pressure Then press SET key Repeat same for Load pressure Use UP and DOWN keys to set up High and Low Frequency use chart above And target pressure High Fre 132Hz Target P 125psi Low Fre 035Hz Each changed parameter required pressing SET key when you done 28 A CAP 876 REV April 2014 ny time pressure and frequency parameters are changed please upload the latest program version to the keypad How to upload and download parameters Note The drive has to be in LOCAL control for uploading and downloading Step Action MENU Go to the Main menu by pressing if you are in the Output mode otherwise by pressing repeatedly until you get the Main menu If REM is shown on the status line press to switch to local contr
31. nnected to How to determine the type of grounding system 10 pe eS o CAP 876 REV H April 2014 Four measurements are required Input voltage line to line Input voltage line 1 to ground Input voltage line 2 to ground Input voltage line 3 to ground Four simple measurements will help determine the network grounding you are connected to These readings should be taken from the line side of the circuit breaker or disconnect before power is applied to the drive Readings 2 3 and 4 are divided by reading 1 to establish a ratio The resulting ratios are then compared to the table values to determine which grounding type is present In the ungrounded floating instance the determining factor is not the ratios present but rather the variability and randomness of readings 2 3 and 4 Case VL L Grounding Type C4 X grounded neutral point symmetrical C2 X grounded corner point nonsymmetrical grounded delta midpoint Pe x nonsymmetrical C4 X Varying level Varying level Varying level ungrounded floating vs time vs time vs time nonsymmetrical CAP 876 REV H April 2014 RFI EMC Filters R5 R1 R4 EM3 WARNING Do not attempt to install or remove EMS3 F1 or F2 screws while power is applied Ensure the RFI EMC filters are disconnected as required for floating networks also known as IT ungrounded or impedance resistance grounded net
32. o design by atmospheric temperature Electrical CAP 876 REV April 2014 It is recommended that a qualified electrician in compliance with standards and local codes do all electrical wiring Be sure to investigate the local requirements before installing the compressor Refer to the wiring diagram before starting any work The power supply should be adequate and free of parasitic loads that will cause an under voltage condition during the operation of the compressor otherwise there will be nuisance electrical shutdowns This equipment requires a properly grounded electrical disconnect switch We recommend the use of time delay fuses in a fusible disconnect for isolating the unit This disconnect should be located so an operator can disconnect the unit without being near the unit in case of an emergency We also recommend the use of a lockout tagout to help insure safety during maintenance of the compressor Per the National Electric Code the time delay fuses should be sized at 175 of the full load amperage FLA found on the motor nameplate Consult the Code if you want to use another style of branch circuit protection WARNING Failure to properly ground compressor package could result in controller malfunction Figure 2 2 Chart of Unit Amp Draw Model Number HP 460Volts GSV 75 75 132 Amps GSV 100 100 187 Amps Y Before applying power necessary to determine what type of network the drive will be co
33. of the compressor C and is sent to the oil separator During the compression cycle oil is injected into the compressor for the purpose of dissipating the heat of compression and to seal the internal clearances The compressed air laden with oil leaves the compressor through the discharge port and enters a reservoir where the oil and air are separated This process delivers a smooth flow of compressed air at the desired pressure SECONDARY ROTOR MAIN ROTOR C piscHARGE Figure 3 2 Compression Cycle 14 CAP 876 REV April 2014 AIR OIL FLOW Air enters the compressor through the air filter inlet valve and compression chamber where it is mixed with oil After compression the air oil mixture is discharged into the oil separator where its velocity is reduced causing most of the oil to drop to the bottom The remaining oil is removed as the air passes through the separator element Oil collected at the bottom of the separator element is returned to compression chamber through the scavenge line The compressed air that is saturated with oil then passes through the minimum pressure valve set to maintain a minimum of 65 psi in the oil separator to ensure a sufficient flow of oil to the compressor The compressed air then enters the aftercooler where it is cooled and discharged to its point of usage A sufficient amount of oil is stored in the oil separator tank and is forced by the pressure of compression from the separat
34. ol Go to the Par Backup mode by selecting PAR BACKUP on the menu with keys CA and lt 2 and pressing E wl To copy all parameters including user sets and internal parameters from the drive to the control panel select UPLOAD TO PANEL on the Par Backup menu with keys LAN and amp Ww 2 and press SS During the transfer the display shows the transfer status as a percentage of completion Press gt if you want to stop the operation After the upload is completed the display shows a message about the OK completion Press SI to return to the Par Backup menu To perform downloads select the appropriate operation here DOWNLOAD FULL SET is used as an example on the Par Backup menu with keys CEN and Kw 2 and press The display shows the transfer status as a ABORT 3 percentage of completion Press if you want stop the operation After the download is completed the display shows a message about the x OK completion Presssw to return to the Par Backup menu Display LOC MENU PARAMETERS EXIT 00 00 ENTER LOC ES BACKUP UPLOAD TO PANEL BACKUP INFO DOWNLOAD FULL SET DOWNLOAD APPLICATION DOWNLOAD USER SET1 EXIT 00 00 SEL LOC WPAR BACKUP Copying parameters 50 ABORT 00 00 LOC UWMESSAGE Parameter upload successful oK 100 00 LOC BACKUP Downloading parameters full set 5096 ABORT 00 00 LOC MESSAGE
35. on Hearing protection A WARNING ALL ELECTRICAL ENCLOSURES CABLE WIRING AND COMPONENTS MUST BE INSTALLED AND GROUNDED IN ACCORDANCE WITH NFPA NATIONAL ELECTRICAL CODE AND APPLICABLE STATE AND LOCAL CODES DO NOT REMOVE OR DEFACE DECAL QAB560 Turn off power supply before maintenance or operating around electric equipment such as starter and motor CAP 876 REVH April 2014 Remove the 4 bolts that secure the air end motor sub frame to the enclosure before test run or startup DO NOT loosen the bolts during transportation Please contact MANUFACTURER or distributor for assistance if necessary Please do not remove labels from the machine CAP 876 REV H April 2014 Safety 1 Become familiar with this manual and follow the instructions before operating the compressor If any malfunctions or trouble occurs do not run compressor until problem is resolved Make sure the compressor has been disconnected before servicing or changing parts Lockout and tagout prior to maintenance 4 To ensure human safety and protect the facility from damage do NOT ignore electrical grounding 5 Wear proper apparel during operation Protective clothing should be worn such as facemask or safety goggles and non slip footwear CAP 876 REV April 2014 Additional Safety information for Air Compressors Like all power tools there
36. or to the thermal by pass valve The thermal by pass valve regulates the flow into the oil cooler depending on the temperature of the oil The thermal by pass valve will open when the oil reaches a predetermined temperature allowing the hot oil to enter the cooler Oil which has not reached this temperature setting will by pass the cooler The oil is then filtered and sent to the compressor to initiate the compression cycle The oil also serves as lubrication for the compressor bearings Section 4 0 System flow chart and components function A System flow chart and component function GSV 75 100 System Flow Chart 25 RETE 55558629720 PIPE AIR CONTROL WIRE AIR OUT CONTROL AIR PIPE lt 1 Air intake filter 14 Check Valve 2 Intake valve 15 Pressure Sensor 3 Air end 16 Air intake filter AP switch 4 Discharge Tube 17 Pressure Sensor 5 Air Oil Separator Vessel 18 Controller 6 Air Oil Separator 19 Inverter 7 Safety Valve 20 Motor 8 Minimum Pressure Valve 21 Coupling 9 AfterCooler Radiator 22 lemperature Sensor 10 Air Outlet Valve 23 Main Fan 11 Oil Drain Valve 24 Oil Level Gauge 12 Thermostatic Valve 25 Inlet control module 13 Oil Filter 26 CAP 876 REV H April 2014 CAP 876 REV April 2014 B Description of system fl
37. ow chart and component function 1 Air flow path refer to the flowchart 1 1 After dust is removed by the intake filter clean air goes through the intake valve into the compression chamber and is mixed with oil The mixture is compressed and delivered through the oil separator minimum pressure valve and after cooler 1 2 Function of parts in the air flow path 1 Air intake filter The air intake filter is a suction filter which is a special purpose air cleaner for the air compressor For normal environmental use clean the dust on the element from inside out with low regulated compressed air every 1 000 hours of operation The air filter LED lamp on indicates that the filter needs to be cleaned or replaced Replace the filter at the recommended interval for your application 2 Intake Valve The check valve of the intake valve is opened during startup As a result the system pressure gradually increases After the compressor is loaded the frequency converter will adjust the motor rotational speed to maintain the system pressure When the air demand is lower than the air supplied the system pressure will reach the unload setting value The compressor then runs in shutdown mode When the system pressure reaches the load setting value the compressor ramps up to meet demand 3 Temperature Sensor The Temperature Sensor sends a signal and displays oil temperature on the control panel Its normal setting is 230 F Lack of oil circulation o
38. peed of the motor effect the life of bearing lubrication You should re grease the bearings every 2000 hrs or once every six months For units in severe duty dusty locations or high ambient temperatures the time interval is 1000 hours A high quality ball or roller bearing grease with the following characteristics should be used 37 CAP 876 REV H April 2014 Standard Service Hi Temperature Service Soap Type Lithium Lithium Grease Viscosity SSU at 48 C 400 550 475 525 Worked Penetration 265 296 220 240 N H Bomb min hrs for 1 38bar drop at 99 C iP K9 Bleeding max weight 10 3 in 500 hrs at 100 C Rust Inhibiting Yes Yes N CAUTION Over greasing is a major cause of bearing and motor failure Make sure not to over grease or to introduce any contaminants during greasing N WARNING Rotating machinery can cause injury or death Shut off main disconnect tagout and lockout power supply to the starter before working on the electric motor To re grease the bearings Switch off the unit disconnect the power and lockout and tagout to prevent accidental restarting Clean grease fittings Remove the relief plug and free the hole of hardened grease Add grease with hand operated grease gun until it appears at the shaft hole in the end plate or the relief plug outlet Re connect the power and run the unit for 20 minutes without the relief plug in place Switch of
39. r a dirty cooler will induce high discharge temperature Do not operate over this temperature otherwise the compressor may be damaged and trip 4 Air Oil Separator Vessel There is an oil level gauge at the bottom of the air oil separator vessel Maintain the oil level in the green range On the bottom of the tank there is a drain valve Remember to drain condensate water every time before startup In addition an oil fill cap for oil replacement is located near the bottom of the tank Add oil only when the oil level is in the red range on the gauge as read when the compressor is on Drain oil only if the oil level is in the yellow range on the gauge overfill as read when the compressor is on 5 Air Oil Separator Element Please refer to the description on oil flow path 6 Minimum Pressure Valve The minimum pressure valve is located at the air discharge outlet from the oil separator Operating pressure is set to be around 65 psi and field settings are not required The functions of minimum pressure valve are shown below A Build up oil circulation pressure to lubricate the air end B When air pressure is over 65 psi it will reduce the flow rate passing thru and protect air oil separator from damage due to large pressure difference and increase oil separator efficiency C Prevents back flow under off load conditions 7 After Cooler Radiator This is the cooler for air cooled series compressors The compressed air is cooled by
40. ri 63133 314 383 1300 or 800 925 5431 www fscurtis com info fscurtis com
41. sance trip 2 Mechanical failure A Such as motor internal phase loss safety valve malfunction or improper setting oil separator clog and or startup with backpressure that results from a non closed intake valve etc B If motor overloads during operation please contact manufacturer immediately to prevent damage to the motor 2 Protection for discharge temperature Discharge temperature setting is 230 F If the temperature exceeds 230 F the compressor will trip One of the most common reasons for high discharge temperature is an issue with the oil cooler For an air cooled compressor if the radiator is clogged the oil temperature goes up resulting in a trip condition because cooling air can t pass through the radiator The high discharge temperature alarm will display at 221 F Clean the dust off the fins of the radiator periodically with compressed air or with a solvent as needed The GSV Series air compressors are designed to operate up to 104 F ambient temperature making it necessary to place it in a well ventilated area When the compressor is tripped due to a high discharge temperature it is unable to restart unless the reset button is pressed 3 Warning Compressor has a warning system for the air intake filter oil filter and oil separator If one of these filters is clogged the controller will show a warning Please replace with factory parts to ensure safety and high efficiency operation 2 995 CAP 876 REV
42. supply of the fan motor contactor If rotation is correct press ON to restart the compressor Observe any warning from panel and LED lights Time delay will be activated after pressing the OFF button the motor will stop automatically after 10 15 seconds Compressed air in the system will be released immediately after pressing the OFF button Figure 5 1 24 CAP 876 REV H April 2014 B Inspection before startup In order to protect the compressor and increase operational efficiency it is necessary to inspect the system prior to operation 1 Open the ball valve below the oil tank to drain the water Condensed water will cause bearing damage and reduce the lifespan of the lubricant 2 Inspect the oil level 10 minutes after shutdown The Oil level could read lower during operation Refill the oil until arrow reaches the Green zone 3 Maintain correct oil level Arrow must be in the green section of the gauge mounted on the separator tank Please do not use lubricant other than CurtisLubePlus FSC 8000 for warranty purposes Make sure the pressure is released before refilling Warning Opening the oil fill cap while pressure is not released may cause injury Fill with oil until arrow reaches the border between 4 gt Black line in the yellow and green regions green region must be in the center of 25 CAP 876 REV April 2014 C During operation
43. t is a crucial factor for efficient and trouble free operation of an air cooled type air compressor please install the compressor in a well ventilated area Clean the dust on the fins of the radiator periodically with compressed air or with solvent B Oil Filter The oil filter takes out metals sludge and unwanted particles from the compressor oil in order to protect bearings and rotors Failure to replace the oil filler may result in lack of oil which will lead to high discharge temperatures and shorter bearing life C Air Oil Separator a Function Air Oil separator consists of a multiple layer filtration element that provides the final removal of oil from the air stream Oil impinging on the inside of the separator element drains directly back into the air oil separator vessel by gravity Oil collected outside the element is returned through tubing to the compressor cylinder Air Oil separator life will vary greatly depending on the conditions of operation the quality of the oil used and the maintenance of the oil and air filters Use CurtisLubePlus FSC 8000 in order to maintain your warranty b Reasons for air oil separator replacement 1 Oil carryover increases 2 Warning on controller indicates replacement 3 Running current increases 3 Cooling system Air cooled Air is drawn in by the fan through the radiator fins and dissipates heat away from the compressed air and oil The highest allowable temperature at the airend discharge is 2
44. the 17 CAP 876 REV April 2014 fan blowing air through the radiator Generally discharge air temperature is 15 20 F above ambient operating temperature A clean and cool environment is a crucial factor for efficient and trouble free operation of an air cooled type air compressor please install the compressor in a well ventilated area 2 Oil flow path refer to the flowchart 1 Description of oil injected flow chart Pressure in the air oil separator vessel pushes oil into the oil cooler The cooled down oil passes through the oil filter for filtration Oil flow is further separated in 2 directions one goes into compression chamber from the bottom of the air end and the other goes into the bearing on the discharge side for lubrication The compressed air and oil mixture is then delivered to the air oil separator vessel again to separate most of the 1 Stage and the rest of the oil mist goes through the oil separator 2 Stage for further separation Finally compressed air passes through minimum pressure valve into the after cooler and is discharged 2 Volume of oil injection The purpose of oil injection in the screw compressor is to dissipate the heat away from the process of air compression Please do not adjust oil volume by the ball valve Seek assistance from MANUFACTURER if necessary 3 Oil flow system A Oil Cooler The function of the oil cooler is the same as the air cooler A clean and cool environmen
45. works Disconnect the ground connection to the internal RFI filters 1 For frame sizes R4 Remove the EM1 screw already removed 2 For frame sizes R5 to R6 Remove screws F1 and F2 The larger drives frame R7 and R8 do not include RFI filters e For detail information use ACS550 User s Manual page 20 21 CAP 876 REV H April 2014 GSV 75 100 Controller Wiring Diagram POWER SOURCE 8 CUSTOMER LI 12 L3 4 alaiziaiziailo l8l8 gt 12 lt lt JP3 v a zz 5 5 4 m Hid H2 gf tuulu a 4 e e EUR 2 5 47 5 ba T 5 E S 6 5 13 5 S F S 5 1 EN AG i TO M CONTROL PANEL lt SV COOLING FAN 6 V 62 5 A1 7 Q 5 ps 120 LT IN GLY F AD 9 24 VDC m PS gt G 2 5 7 8 2 5 9 7 2 5 lt 15 472 JP4 a 50 30 20 18 21 po 131 2 7 B n 8 J THA Bg lt On DRIVE J 2 op ABB ACSSS0 50 sh 5 d ira JP4 8 3 24 AGNDiCDG
Download Pdf Manuals
Related Search