Illumina SR Manual v.2.0_ENG
Contents
1. SR Se CONTENTS Chapter 1 Getting Started Chapter 5 Additional Information 3 What You Need 23 FAQ and Troubleshooting 3 Safety Considerations 24 Warranty Information 4 Illumina SR Specifications 24 Contacts 5 LED Pad Specifications 6 Components 6 Out of the Box Chapter 2 Basics 7 Getting to Know the Features 9 Installing Your Illumina SR 14 Operation 14 Button Controls 15 Menu Structure Chapter 3 Advance Features 16 Light Manager 18 Quick Motion 18 Settings 19 Info 19 Updating Your Illumina Firmware Chapter 4 Maintenance amp LED Module Guide 20 Considerations and Guidelines 21 Cleaning the Central Air Shaft 21 Removing Dust and Debris 22 LED Modules 23 Firmware Upgrade WARNING To avoid injury read all the operating instructions presented within this guidebook When using or installing electrical devices take care and or consult with a professional Be sure to follow all directions carefully failure to do so may result in damage to your Vertex Illumina and void the warranty Dealers or the manufacturer are not responsible and cannot be held accountable for any personal prop erty damage and or loss of livestock resulting from the misuse of products CHAPTER 1 Getting Started What You Need Thank you for your purchase of the Vertex Illumina SR LED Fixture This User Manual is your guide to getting the most out of your product Please be sure to read all of the instructions prese2. extremely hot over The AUTO setting only turns on the fans when the fixture heating reaches a the fixtures temperature threshold Individual LED s and Models SR 900 SR Follow connection instructions pg 12 to 13 being sure to or LED Modules are connect all power sources to the Splitter Box PRIOR to con not running necting the Control Cable from the fixture Color Channels Check the Light Composer menu 1 4 1 and Color Channels menus 1 4 2 to 1 4 4 and make sure at least one of the channels is set above 0 Individual LED Mod If all Color Channels are functioning properly check with your ules authorized Vertex dealer Moonlights are not Moon Selection Moon If set to the MOON CYCLE option Moon Lights may not illu running Cycle Option 1 4 5 3 minate during the days of the New Moon Increase the Moon Light intensity to change this Moon Light intensity Check your Moon Light intensity options During Moon Cycles the Ilumina will automatically shut down any LED s that begin to flicker due to low current input Increase your intensity to correct this Main body of the Display installation Be sure that no water is splashing onto the unit This type of fixture is rusting damage is not covered by warranty LED Splash Gaurd is Display installation Do not sit the Illumina fixture directly on top of any surfaces bubbling damaged This type of damage is not covered by warranty 23 CH
3. FUNCTION FUNCTION FUNCTION LIGHT MANAGER QUICK MOTION FAN OFF SETTINGS OFF DEMO LANGUAGE AUTO DEFAULT ENGLISH ON NO MOON DEUTSCH MISC MOON LIGHT ITALIANO FUNCTIONS CUSTOM FRANCAIS SPARE MODULES LIGHT COMPOSER ESPANOL FACTORY RESET WHITE TIME FORMAT INFO ROYAL BLUE 24 HOURS BLUE AM PM MOON SELECTION TIME AND DATE NO MOON DISPLAY MODE MOON LIGHT NORMAL MOON CYCLE INVERSE CHAPTER 2 Basics Menu Structure Use the following table to orient yourself within the menus LIGHT MANAGER _ wr 3 DEFAULT ROYAL BLUE MOON SELECTION a SPARE MODULES FACTORY BEGET 3 b MOONLIGHT H 15 CHAPTER 3 Advanced Features Light Manager Main Menu 1 The Light Manager is the main interface from which you will program your Vertex Illumina Within it you will find the following functions OFF DEMO DEFAULT CUSTOM A Functions 1 1 OFF Select this function and hold the SELECT button to turn the unit off 1 2 DEMO Select this function and hold the SELECT button to begin a preprogrammed demo mode 1 3 STANDARD Make Moon Light selections here 1 3 1 NO MOON No Moon Light cycle 1 3 2 MOON LIGHT Standard Moon Light function See Section 1 4 5 2 on the following page 1 4 CUSTOM This Submenu contains all of the User configurable light settings 1 4 1 LIGHT COMPOSER This application allows you to create and test specific light outputs and uses the fo
4. Plug the Illumina fixture cable to the Splitter Box This last step will activate your Illumina and ready it for programming 6 CHAPTER 2 Basics Getting to Know the Features This section will detail help familiarize you with each of the Vertex Illumina s aspects and components Vertex Illumina Fixture The body of the Vertex Illumina is constructed from anodized extruded aluminium and has been designed with the following considerations e Thermovap heatsink design with a high bypass airshaft exchange central NS to an oversized bilateral heat sink Ws e SilenX Ixtrema Pro IXP 52 14 fans produce less than 14dBm noise and move up to 24 CFM each e Onboard programmable control panel with built in wireless network functionality w V Link accessory e Streamlined one cord construction for all fixture lengths and models serving to effectively minimize clutter preserving the aesthetics of the fixture e Two adjustable suspension bridges allow for maximum suspension flexibility during installation or the Alu Mounting Braket optional e Modular LED pad platform requires no wiring or soldering for any replacements or upgrades e Auxiliary slots located between each of the LED pads allow for nearly limitless spectral composi tions NOTES The Vertex Illumina is meant to be suspended above a display Though humidity resistant it is not waterproof Be sure that it is mounted and protected from water spray coming fro
5. point source of illumination over an aquarium Please note that while the unit is humidity resistant it is NOT waterproof It is absolutely crucial to mount the unit to a sturdy foundation Direct contact with water will damage the unit and void war ranty We strongly recommend that installation only be performed by a certified professional Similarly measures must be taken to keep all of the power sources splitter control box and cables dry and protected from humidity Exposure to water and or salt will damage these components and void warranty 3 CHAPTER 1 Getting Started Illumina SR Specifications SR 300 260 360 Dimensions 300mm x 300mm 12 x 12 Footprint 32mm 1 26 45mm 1 77 Center Height Weight 3 2 kg 7 1 Ibs LED Modules 2 Auxiliary Slots 1 Mean Well 1 Fans 1 x SilenX Performance 96W 112W 90 2 0 SR 900 260 360 Dimensions 900mm x 300mm 12 x 12 Footprint 32mm 1 26 45mm 1 77 Center Height Weight 10 kg 22 5 Ibs LED Modules 6 Auxiliary Slots 5 Mean Well Drivers 2 Fans 2 x SilenX Ixtrema Pro IXP 52 14 Performance 289W 335W 90 270 V 50 60Hz SR 600 260 360 Dimensions 600mm x 300mm 12 x 12 Footprint 32mm 1 26 45mm 1 77 Center Height Weight 6 6 kg 14 55 Ibs LED Modules 4 Auxiliary Slots 3 Mean Well Drivers 3 ans ema Pro IXP 52 14 Dimensions 1200mm x 300mm 12 x 12 Foot
6. 28DAYS OK 17 CHAPTER 3 Advanced Features Quick Motion Main Menu 2 The Quick Motion feature allows you to quickly test and adjust any Custom settings you have defined and saved using the Light Manager Once selected the Quick Motion will quickly run the Illumina through an accelerated light cycle You can exit at any time by pressing any of buttons on the control console Settings Main Menu 3 Use this menu to configure the interface functionality of the Illumina LANGUAGE TIME FORMAT TIME AND DATE DISPLAY MODE FAN MISC FUNCTIONS A Functions 3 1 LANGUAGE Select from a list of languages ENGLISH DEUTSCH ITALIANO FRANCAIS ESPANOL A Press and hold lt OK to select and save your language Press and hold ESC exit without saving any settings 3 2 TIME FORMAT Use this menu to select between 24 Hour mode 3 2 1 and AM PM mode 3 2 2 3 3 TIME AND DATE Set the time by using the lt OK and ESC buttons to toggle between the time values Use the and buttons to adjust each value Press and hold lt OK to select and save your time settings Press and hold ESC exit without saving any settings 18 CHAPTER 3 Advanced Features Settings Main Menu 3 Functions cont 3 4 DISPLAY MODE Toggling the display mode will change backlighting of the interface display Make your selection by pressing and holding lt OK to select and save the setting Press and hold ESC exit w
7. APTER 5 Additional Information Warranty Information The Vertex Illumina LED Fixture comes with a two 2 year limited Manufacturer warranty The Mean Well AC Adapter s come with a two 2 year limited Manufacturer warranty Parts that have been damaged due to user error and misuse will not be eligible for warranty replace ment Vertex Aquaristik reserves the right to warranty products based upon inspection All warranty related issues should be handled at the point of purchase location by trained staff Please contact your dealer for warranty replacement services Contacts For additional information regarding this or any other Vertex Aquaristik products please either con sult with your dealer or the following resources 24 Vertex Aquaristik HOME PRODUCTS NEWS ABOUT US CONTACT DEALERS SUPPORT VERTEX AQUARISTIK REALIZATION OF THE MODERN AQUARIA website www vertexaquaristik com email info vertexaquaristik com Thank You
8. bility NOTES As the unit is heavy please note the weight of your Illumina fixture and consult with an expert prior to in stallation over the display CHAPTER 2 Basics Installing Your Illumina SR Please read the following instructions thoroughly and consult with an expert before installing your Il lumina The fixture should always be located above your display in a well ventilated space and should not be touching any surfaces once suspended Locate the unit away from areas of high humidity and or water and salt spray The manual explains the installation with the optional Suspension kit for the Mounting Braket see the manual which is coming with the Braket Cables optional Begin by noting the two different ends of the steel ca bles One end will have steel bolt This is the stopper end and it goes anchor side The other will be a bare line This end threads through the cable clamp and is fixture side At this point do not attempt to trim shorten or crimp any of the cables Assembling the Suspension Kit optional Locate the rubber O rings and loop them over each of the threaded ends of the Cable Clamps Take each Cable Clamp and install to the Illumina fixture by threading the bolts through the adjustable suspension bridges found in the center channel of the fixture Hand tighten only CHAPTER 2 Basics Installing Your Illumina SR Next take the bare end of the cable and thread it through the eye hole of t
9. bles e SR 300 600 includes one Driver and Power Cable SR 900 1200 includes two Drivers and two Power Cables e SR 1500 1800 includes three Drivers and three Power Cables e Vertex Illumina Splitter Box 900 1200 1500 amp 1800 models only e Manual Optional Parts not Included please ask your dealer for more information e Suspension Kit e Illumina Alu Mounting Braket AX 2x Illumina Acrylic Holders various sizes Auxiliary Pads in different Collors Out of the Box Your Vertex Illumina SR will come out of the box with the main body preassembled You will not be re quired to install any LED Pads or electronics Do not attempt to open your Illumina SR Any installations requiring disassembly of the fixture should only be done by an authorized Vertex dealer Upon removing your Vertex Illumina from its package examine the fixture and all of its components for any damages After carefully inspecting the components and reading this guide you will ready to begin installation Note Please take the following instruction into consideration before attempting to operate your fixture When attempting to connect the power cables to each of the Mean Well Drivers ensure that the fit tings form a firm union DO NOT CONNECT THE FIXTURE CABLE TO THE SPLITTER BOX YET l Plug each of the power cables into a GFCI Surge Protected electrical outlet 2 Connect the Mean Well Drivers to the Vertex Illumina Splitter Box ensuring firm union 3
10. d and installed you will now be able to thread the male adapters in completing the mounting pro cess Draw the cables through the cable clamps as de sired A leveling ruler is recommended to achieve perfect horizontal balance Before powering up the fixture ensure that the unit and surrounding area are free of dust and humidity 11 CHAPTER 2 Basics Installing Your Illumina SR To begin powering up your Vertex Illumina first plug all the power cables to their respective Mean Well AC Adapter Driver Units Then connect each of the power cables into a GFCI Surge Protected electri cal outlet Before plugging the fixture into an wall outlet arrange the cord in an anti drip loop as pictured to the left This arrangement will prevent any dripping wa ter from entering the electrical socket Failure to accomodate for this simple measure can lead to a fire hazzard This is true of all elec trical appliances within the vicinity of the aquari um or any body of water Once all of the Drivers are assembled and plugged to a power source you can proceed to connecting the control cable of the Illumina fixture Depending on which model you have the process will differ slightly 12 CHAPTER 2 Basics Installing Your Illumina SR SR 300 amp 600 To power up these models connect the Control Cable from the fixture to the AC Adapter Driver connector cable Once properly connected the display module o
11. he male end of the Socket Anchor Pull it until the cable is fully threaded through the fitting as shown The stopper will hold once it reaches the eye hole of the fitting Now take the cable and thread it through the Cable Clamp It will push out from the side wedge of the fitting and can be pulled through from there Continue to pull the cable through the fitting Do not worry if you draw too much length as this can later be adjusted You can use the central channel to hide any excess cable 10 CHAPTER 2 Basics SOCKET ANCHOR CEILING FEMALE The Female side of the Socket Anchor is the base point for suspending the fixture In order to mount this part you will need a sturdy surface such as a wooden crossbeam please refer to the weight chart and consult with an expert prior to installation and an appropriate screw bolt of at least 2 in length Be sure that the head of the fastener is not larg er than the inner diameter of the anchor and affix as shown When setting the anchors consideration must be taken into account for the length of the fixture and the width between the adjustable suspension bridges See the following table for optimal spacing between each suspension bridge MODEL SUSPENSION BRIDGE SPACING Centered Positioning SR 300 110mm 4 25 SR 600 410mm 16 1 SR 900 610mm 24 0 SR 1200 1010mm 39 75 SR 1500 1310mm 51 5 SR 1800 1610mm 63 4 With the female Socket Anchors properly space
12. ith a slightly dampened microfiber cloth Be sure to clean the underside of the unit to maintain optimal heat dispersion To remove any salt water stains or calcifications use a mild soap solution along with the micro fiber cloth Do not apply the cleansing solution directly to the fixture Use only a microfiber cloth and water to clean the splash shield and end panels If damp allow the unit to fully dry fully before reinstalling over the display 21 CHAPTER 5 Additional Information LED Modules Each Vertex Illumina fixture can upgraded with new LED Modules allowing you to adopt the latest tech nologies and or further refine the light spectrum Refer to the following table for LED Module information Model LED Modules Auxiliary Slots SR 300 SR 600 SR 900 SR 1200 SR 1500 SR 1800 Installation information for LED upgrades and Auxiliary Modules are included with the respective prod ucts All modules should only be installed by an authorized Vertex technician Damages resulting from user error will not be covered by the warranty For more information regarding Auxiliary Modules and other upgrades please visit the Vertex Aquaris tik website at www vertexaquaristik com Firmware Upgrade It is recommended that you keep your Illumina Firmware upgraded to the latest version please refer to the Vertex Aquaristik website www vertexaquaristik com prior to installing any modules or upload ing light manageme
13. ithout saving any settings 3 5 FAN The fan settings can be adjusted to OFF 3 5 1 AUTO 3 5 2 recommended or ON 3 5 3 3 6 MISC Use this setting to adjust the Radio Channels between 01 15 to compensate for any interfer ence between the Vertex Illumina the V Link accessory and other remote devices 3 7 FUNCTIONS This menu has the optional SPARE MODULES 3 7 1 and FACTORY RESET 3 7 2 selections SPARE MODULES is initially deactivated but can be accessed with the installation of optional Auxiliary Modules and their support firmware Further details regarding these items are available from authorized Vertex Aquaristick dealers Use FACTORY RESET to clear user programmed settings from the unit Make your selection by holding OK WARNING Settings once reset are deleted permanently Info Main Menu 4 4 INFO This selection displays the serial numbers and current software versions installed on your fix ture It is recommended that you keep your Illumina up to date with the latest software which can be found on the Vertex Aquaristik website www vertexaquaristik com Updating Your Illumina Firmware In order to update your Fixture you will require a V Link USB Stick This accessory can be purchased at your authorized Vertex Aquaristik retailer 19 CHAPTER 4 Maintenance Considerations and Guidelines Your Vertex Illumina must be routinely maintenanced to keep it performing optimally Be sure to unplug all power t
14. llowing interface LIGHT COMPOSER WHITE 00 100 ROYAL BLUE 00 100 BLUE 00 100 OK Use the lt OK and ESC buttons to scroll between the channels Use the and buttons to adjust the values to the desired level Press and hold lt OK to exit the Light Composer while retaining your color composition no lighting schedule Press and hold ESC exit without saving any settings 16 CHAPTER 3 Advanced Features Light Manager Main Menu 1 Functions cont 1 4 2 WHITE 1 4 3 ROYAL BLUE 1 4 4 BLUE These options allow you to configure each LED color channel independantly Within the selections you will find the following interface CHANNEL NAME INTENSITY 00 100 SUNRISE 00 00AM RISETIME 00 00H SUNSET 00 00PM DAWNTIME 00 00H OK Press and hold lt OK to exit each channel while retaining your color composition no lighting schedule Press and hold ESC exit without saving any settings 1 4 5 MOON SELECTION Use this Submenu to control the Moon Light behavior of your Illumina within the your light schedule 1 4 5 1 NO MOON No Moon Light cycle 1 4 5 2 MOON LIGHT Standard Moon Light with intensity adjustment MOONLIGHT INTENSIT Y 00 100 OK 1 4 5 3 MOON CYCLE Use this option if you want the Moon Light to operate on a montly Lunar Cycle The Illumina will simulate the natural wax and wane phases of the moon LUNAR CYCLE INTENSIT Y 00 100 FULL MOON IN 00
15. m overflows and or splashing and bubbling water e Do not attempt to move the LED pads within the fixture They are set in place to allow for exact placement of auxiliary LED pads and sealed with a thermal paste backside e Do not clean with harsh acidic or alkaline cleaners solvents which may destroy the finish e Do not set the fixture on top of any surfaces while it is running you will damage both the surface and the LED splash shield These types of damages are not covered by the warranty 7 CHAPTER 2 Basics Mean Well AC Adapter Driver Unit e 160W 220W AC DC Single Output Desktop Adapt ers comply with worldwide energy regulations for exter nal power supplies including ENERGY STAR EISA 2007 and MEPS Very low No Load power consumption lt 0 5W and up to 94 efficiency offers energy saving characteris tics in both standby and active modes NOTES e Non waterproof part Keep away from humidity Vertex Illumina Splitter Box e Connection Indicator confirms operating connection between Driver and Illumina fixture NOTES e Non waterproof part Keep away from humidity Can be affixed using the side brackets Be sure to follow the connection procedure be fore connecting the Control Cable of the Illumina to the Splitter Box Vertex Illumina Suspension Kit optional e High tensile Steel Aircraft cables and cable clamp fittings provide secure durable suspension and maxi mum installation flexi
16. n your Illumina should light up and begin Initial izing After a few moments you will be ready to begin programming your lights SR 900 1800 Begin by plugging the AC Adapter Driver con nector cables to each of the slots in the Splitter Box Plug each connecter in sequentially See im age below for details per model Connect the Control Cable of the fixture to the splitter box The Illumina will begin initializing and after a few moments be ready for pro gramming SR 900 1200 F CHAPTER 2 Basics Operation With your Vertex Illumina is powered up you will now be able to program your lighting spectrum and schedule Button Controls The Vertex Illumina interface consists of a view ing screen and four control buttons The fuction of each of the buttons is as follows 1 SELECT OK Confirms selection within main menus Scrolls to next parameter option within submenus Press once to select next hold exit Submenu and save settings 2 A t Next selection within menus Param eter value up within submenus 3 V Previous selection within menus Pa rameter value up within submenus 4 ESC Cancels selection to previous screen within main menus Scrolls to the previous parameter op tion within submenus Press once to select previous hold to exit submenu without saving settings System Interface Use the following table to familiarize yourself with the functions of the Illumina interface
17. nance and or replacement of internal components Damages caused by user error will void the warranty of the unit Always mount the electrical components of the fixture away from humidity and moisture e Only plug the Illumina into a GFCI and surge protected power supply Failure to do so will void the warranty of the unit 20 CHAPTER 4 Maintenance Cleaning the Central Air Shaft The Central Air Shaft is crucial towards maintaining proper operating temperatures and LED output life Therefore it is recommended that you clean perform routine maintenance to keep the shaft free of dust and other particulates Note Do not attempt to open the the body to access the Air Shaft Do not pour liquids into the air shaft Use commercially available Air Dusters Canned Air products to expel dust from channel It is recommended that you this in a well ventilated outdoor area Follow the guidelines on the product and spray the pressurized air in short burst beginning from one side of the fixture through each of the fans air vents and progressing to the other side of the fixture Once the Central Air Shaft is properly cleaned you can now begin cleaning the main body of the fix ture Removing Dust and Debris A microfiber cloth is recommended for this step Do not use any abrasives or harsh chemicals to clean the body as they may destroy the finish Remove surface dust by gently wiping all exposed surfaces of the Illumina w
18. nt software to the fixture Please refer to the Vertex V Link Owner s Manual for more information 22 CHAPTER 5 Additional Information FAQ and Troubleshooting PROBLEM cece sorurons Fixture will not Models SR 300 Check the power source and make sure all connections are power up SR600 firm and undamaged Models SR 900 SR Follow connection instructions pg 12 to 13 being sure to connect all power sources to the Splitter Box PRIOR to con necting the Control Cable from the fixture Mean Well AC Adapter Make sure all connections are firm and undamaged Be sure only to plug the Drivers only to a GFCI and Surge Protected electrical outlet Fixture is powered Light Manager Make sure the Light Manager is not set to OFF Follow the but LED Pads are guidelines in Chapter 3 pg 16 to 19 to program a light not illuminating schedule Check the Light Composer menu 1 4 1 and Color Channels menus 1 4 2 to 1 4 4 and make sure at least one of the channels is set above 0 Time and Date Callibrate the Time and Date with the current schedule e g Submenu 3 3 Make sure AM and PM settings are correct Fans are not run Fan Submenu 3 5 Check settings and make sure Fans are set to AUTO or ON ning The AUTO setting only turns on the fans when the fixture reaches a the fixtures temperature threshold Fixture is running Fan Submenu 3 5 Check settings and make sure Fans are set to AUTO or ON
19. nt within prior to installing and operating your fixture Retain this manual in a safe place for later referral as required In order to properly use the Vertex Illumina you will need o An aquarium or illumination subject appropriately sized to the length of your Illumina A mounting point above the tank able to support the weight of your respective Illumina optional This mounting point will need to allow for two anchor points You will need to maintain at least 4 of height between the surface of the water subject and the bottom surface of the Illumina o There must be at least 5 6 of ventilated space around the Illumina at all times to allow for proper and thorough air circulation The Illumina must at no time come into contact with any of the mounting surfaces and or water The Illumina must be suspended in such a way as to protect it from any water spray or emergent plants or animals objects o GFCI protected electrical outlets for each Mean Well driver The outlets required are as follows SR 300 One 1 outlet SR 600 One 1 outlet SR 900 Two 2 outlets SR 1200 Two 2 outlets SR 1500 Three 3 outlets SR 1800 Three 3 outlets Please be sure to connect your Illumina only to electrical outlets of the proper voltage 110 or 220V Failure to do so will result in failure of the unit and is not covered by warranty Safety Considerations Your Vertex Illumina has been designed to be used as a
20. o the unit by disconnecting the control cable from the Splitter Box For thorough cleaning you will also want to dismount the fixture from the hanging kit To extract the Steel Cables from the Cable Clamps you will first want to ensure that the Il lumina fixture is supported and or removed from its position over the display Begin by firmly depressing the lock fitting into the body of the Cable Clamp This will loosen the binding mechanism and allow you to pull the Steel Cable away from the Cable Clamp Repeat with the other Cable Clamp and you will not be ready to perform routine maintenance on your fixture Before you beging with any further maintenance operations be mindful of the following points e Do not attempt to disassemble your Vertex Illumina without specific instruction This action should only be done by an authorized Vertex technician and any failure caused by user error will void the war ranty of the unit e Do not clean with harsh acidic or alkaline cleaners solvents which may destroy the finish e Do not power the unit during the cleaning process e The Illumina is humidity resistant but not waterproof Do not immerse or attempt to cleanse the fixture with water or solvents Always apply any cleansers to a soft cloth Microfiber or commercially available dusting materials and never directly to the body of the fixture Always take your Illumina to an authorized Vertex dealer for any concerns regarding the mainte
21. print 32mm 1 26 45mm 1 77 Center Height Weight 13 6 kg 30 0 Ibs LED Modules 8 Auxiliary Slots 7 Mean Well Drivers 2 Fans 2 x SilenX Ixtrema Pro IXP 52 14 Performance 385W 447W 90 270 V 50 60Hz CHAPTER 1 Getting Started Illumina Specifications SR 1500 260 360 Dimensions 1500mm x 300mm 12 x 12 Footprint 32mm 1 26 45mm 1 77 Center Height Weight 15 5 kg 34 17 Ibs LED Modules 10 Auxiliary Slots 9 Mean Well Drivers 3 Fans 3 x SilenX Ixtrema Pro IXP 52 14 Performance 482W S559W 90 270 V 50 60Hz Cree CHANNELS White XTE 130lIm W Royal Blue XTE 475mV Blue XTE 30 6m W LEDs per Module 16 Performance Module 43 78W 90 270 V 50 60Hz 50 000 hours lt 135 F core diode temperature SR 1800 260 360 Dimensions 1800mm x 300mm 12 x 12 Footprint 32mm 1 26 f 45mm 1 77 Center Height Weight 19 kg 41 9 Ib LED Modules 12 Auxiliary Slot 11 Mean Well Dfivers 3 Fans 3 x SilenX Ixtgema Pro IXP 52 14 Performance 578W 670 90 270 V 50 60Hz White XTE 148lm W Royal Blue XTE 550mV Blue XPG 39 8lm W LEDs per Module 16 Performance Module 50 82W 90 270 V 50 60Hz 50 000 hours lt 135 F core diode temperature CHAPTER 1 Getting Started Components Your Vertex Illumina SR will include the following components e Illumina fixture Mean Well Driver s and their respective power ca
Download Pdf Manuals
Related Search