AP-Ext-N User Manual
Contents
1. m WIRELESS TERABGEAM AP Ext N User Manual Contact Terabeam www terabeam com 8000 Lee Highway Falls Church VA 22042 Office 703 205 0600 Fax 703 205 0610 Sales 1 888 297 9090 MNL 500275 001 Version 1 0 Jun 2005 AP Ext N User Manual LIMITED WARRANTY Terabeam Wireless Terabeam warrants that your device is free of defects in material and workmanship for a period of one year after initial purchase Terabeam will in this period of time repair or replace any Terabeam product returned to the factory freight prepaid The Terabeam warranty covers repairs or replacement at Terabeam s option of the product only Terabeam is not responsible for the cost of removal reinstallation or shipping to the place of repair Terabeam does not extend or modify its warranty period as a result of repair or replacement Terabeam reserves the right to void a warranty and or make reasonable charges for repair of a unit if the warranty seal is broken or the unit displays evidence of misuse abuse or tampering Terabeam is not responsible for damage to any other equipment or property or any other consequential or incidental damages of any kind whether based on contract negligence or strict liability Maximum liability shall not in any case exceed the purchase price of the unit Warranties give you the buyer specific legal rights You may also have other rights that vary from state to state This warranty is only extended t2. The Cat 5 DC Power Injector is not in a waterproof enclosure and must be protected from the weather It can be permanently mounted to a surface using the double stick tape found on the back of it 2 4 Power Supply The AP Ext N antenna kits come with a 110 220 VAC to 48 VDC power supply that has a standard barrel plug center pin positive tip and outer ring negative 2 5 Hardware Installation Perform the following procedures once you have determined the optimal location for the external antenna and installed it following the manufacturer s instructions 1 Use the brackets and screws to mount the flat panel enclosure to a pole with a maximum diameter of up to 1 3 4 inches as close as possible to the antenna 2 Connect the antenna to the N type connector in the back of the AP Ext N using a short coax cable as shown in figure 2 1 3 Ensuring that there is no DC power applied to the cable plug the 6 pin N male round connector of the outdoor Ethernet cable into the rear jack of the flat panel enclosure making sure the notch on the connector is correctly aligned with the tab on the jack as shown on Figure 2 2 Turn the round locking nut clockwise as you push in until it securely fastens onto the jack Please verify that the round connector is properly plugged into the rear jack of the antenna prior to connecting DC power because it is possible to push it in the wrong way if enough force is used If DC power is applied and the connector
3. the surge protected DC Injector to ground as shown on Figure 2 3 7 Connect the barrel plug of the power supply to the DC Power jack on the Cat 5 DC Power Injector then plug the Power Supply into an AC outlet Check that the Power LED turns on If there is traffic over the wireless medium the Wireless Link LED should be flashing If the Ethernet port is active the Ethernet Link LED should be flashing Radio Status should be off it turns on only when there is a malfunction of the internal card refer to Fig 2 4 Also a water proof plug is located next to the LED label You may remove this plug to gain access to a reset push button inside the AP Ext N for disaster recovery or if so instructed by your Terabeam support representative during troubleshooting or technical assistance 8 Configure the AP Ext N using the Configurator software Please refer to the Marquee Series Configuration Guide available as a pdf file on your CD ROM Also an online help is available by pressing F1 or clicking Help gt Index from the main screen Figure 2 3 Installation of the Terabeam Surge Protected DC Injector for Maximum Grounding Protection AC Power ye Wire Power Supply Se a a Surge Proieoled DE Power Injector A RJ 45 Ethernet Connector E To Router Switch or Hub lt lt lt L ro AP Ext N If connected to a PC use a Terabeam Surge cross over cable or adapter Protected DC Injector Water Proof Plug R
4. and Fresnel Zone between it and the client stations antennas The AP Ext N should be installed outdoors as close as possible to its antenna so that the coax cable between the antenna and the unit is kept as short as possible For maximum range and the strongest signal the antenna must see the clients antennas in order to be connected If they do not have this clear line of sight you will likely not get a reliable long range wireless connection The only way to accurately determine your coverage area is to put up the AP Ext N and its antenna in the best locations available and run some tests NOTE It is strongly recommended that you configure and test the unit prior to deploying it in the field Set up a mini network that resembles your actual configuration as close as possible By using such a mock up troubleshooting potential problems will be much easier than if you already installed the equipment in the field Read through this entire Section 2 to understand how to install the hardware 2 2 Mounting the AP Ext N A 2 4 GHz antenna must be used with the AP Ext N unit If you are not using an omnidirectional the antenna may be mounted either vertically or horizontally polarized using its own hardware Please note that both ends of the link must use the same polarization The antenna can be mounted to a mast or pipe as shown in Figure 2 1 When covering an area with laptops or PDAs a sector antenna should be installed horizontally
5. are and documentation A Terabeam outdoor Ethernet cable must be ordered separately Available lengths are 50 100 200 or 300 feet maximum length The latest software and User s Manuals can also be found at htto www terabeam com support downloads php and http www terabeam com support documents php Figure 1 1b shows a typical application of the AP Ext N Ver 1 0 Page 2 Jun 2005 AP Ext N User Manual Figure 1 1a AP Ext N 110 220 VAC Power Supply and DC Power Injector a n 5 ate a TT i Figure 1 1b Typical Application Omni Antenna AP Ext N Ethernet Cable f DC Power Injector _ ee ee aes Client Equipment Short Coax Cable Outdoor Ethernet Cable ee i DC Power 4110 220 VAC Ver 1 0 Page 3 Jun 2005 AP Ext N User Manual Section 2 Installation Safety Warnin This antenna transmitter device must be fixed mounted on outdoor permanent structures with a separation distance of at least 2 meters 6 56 feet from all persons Users and installers must adhere to the A antenna installation instructions and transmitter operating conditions in CAUTION order to comply with the FCC s RF exposure requirements 2 1 Locating the AP Ext N The most important aspect of setting up the AP Ext N is the location and aiming of both the unit and its external antenna For maximum range up to several miles the antenna must have clear unobstructed line of site LOS
6. been made to make this manual accurate and complete Terabeam Wireless assumes no responsibility for any errors that may appear in this document Ver 1 0 Page ii Jun 2005 AP Ext N User Manual Section 1 Overview 1 1 Description The AP Ext N is an 802 11b Access Point AP built into a flat panel enclosure It is ideal for providing maximum coverage over a focused area such as 802 11b Hot Spots hotels airports office buildings apartment complexes etc It is easy to install and features the functionality of the Terabeam AP Plus Access Point including 128 bit WEP Wired Equivalent Privacy and the new Agere WEP Plus lts Windows based SNMP compliant Configurator software makes it easy to configure your system as well as to centrally control your network The AP Ext N housing is waterproof and intended for pole mounted outdoor installations Two versions of the AP Ext N are available the standard series AP Ext N and the AP LR Ext N with the addition of an integrated bi directional fixed amplifier to boost range and improve reception The WLAN device located in the unit gets its power from the DC Power Injector which puts DC power onto the Ethernet cable Up to 300 feet of Ethernet cable ordered separately between the DC injector and the unit can be used with no signal loss Both the AP Ext N and the AP LR Ext N version use a 110 220 VAC to 48 VDC power supply Ver 1 0 Page 1 Jun 2005 1 2 AP Ext N User Manual AP Ext N Feat
7. emove to Gain Access to Reset Push Button gt Figure 2 4 shows the AP Ext N label located on the back of the flat panel LEDs appear to the right that indicate the status of Power Radio Wireless Link and Ethernet Link cic 48 V System E N type Connector for a x External Antenna Figure 2 4 AP Ext N Label and LEDs Ver 1 0 Page 7 Jun 2005
8. is not properly plugged damage to the electronics of the unit or the connector itself may occur which will not be covered by the factory warranty Figure 2 2 Plugging the Outdoor Ethernet Cable w Po aa y Plug the connector into the jack by aligning the notch with the tab Caution Be sure DC Power is not applied when plugging the cable If DC Power is applied while you are attempting to insert the round connector into the jack it is possible that as you rotate the plug in an effort to find the key DC power pins will momentarily touch the Ethernet pins If this happens the Ethernet circuitry on the board will be A damaged Also do not apply excessive pressure when you insert the CAUTION round connector or the pins will pop out Any damage caused by this action will not be covered by the factory warranty and will be a billable repair Ver 1 0 Page 6 Jun 2005 AP Ext N User Manual 4 Attach the other end of the outdoor Ethernet cable to the Cat 5 DC Power Injector at port RJ 45 labeled To Antenna 5 Connect the Ethernet cable labeled To PC Router from the Cat 5 DC Power Injector into a regular port on your router switch or hub If you connect to a laptop or PC use a cross over cable or adapter 6 Perform an Earth ground connection to any of the rear bolts of the unit the mounting brackets or the mast if metallic refer to Fig 2 1 For maximum protection also connect the metal wire of
9. o purchases made in the United States of America or its possessions SPECIAL WARRANTY NOTICE The warranty is null and void if any of the following occurs The product enclosure is opened The connections are not properly waterproofed The device is installed improperly or with incorrect connectors The round connector of the outdoor Ethernet cable if provided is improperly plugged into the rear jack of the enclosure The device or DC Power Injector if provided are physically damaged The device is operated outside the recommended DC power specifications The device is damaged by extreme forces of nature lightning or Acts of God Ver 1 0 Page Jun 2005 AP Ext N User Manual TABLE OF CONTENTS Section1 Overview 1 Bi A o a aa aerate 1 da APENAS e et edi o bo 2 OAP E N A a a lidia 2 Section 2 Installation 4 2 WOCAUNG he AP E XEN eara a OE ENANA 4 22 IMIOUNTIAG UNG APR EX Nesie a E E E E aE nines 4 23 A a aaa 6 2A OW El OUD DIY corakna a a E pesoctcoSiaal 6 25 Harawale installalo sesana a E a E Ea 6 2005 Terabeam Wireless All Rights Reserved No part or parts of this document may be reproduced translated stored in any electronic retrieval system or transmitted in any form or by any means electronic mechanical photocopied recorded or otherwise without the prior written permission of Terabeam Wireless The information in this document is subject to change without notice Although every effort has
10. polarized since this will match the polarization of the internal antennas in the WLAN cards When installed outdoors it is very important that the round connector on the back of the unit be properly waterproofed Ensure that a high quality all weather resistant electrical tape and or other water sealant method such as Permagum or equivalent is utilized Silicon sealants are not recommended since they are hard to work with do not ensure a 100 waterproofing of the connectors and are difficult to remove if ever necessary The antenna and the AP Ext N or the mast where they are bolted to should be connected to an Earth ground Fig 2 1 shows the possible grounding points that you can use Table 2 1 gives a list of Terabeam recommended antennas that you can use with the AP Ext N Ver 1 0 Page 4 Jun 2005 Ver 1 0 AP Ext N User Manual Figure 2 1 Outdoor Pole Mount Installation Omni Antenna AP Ext N Ethernet Round Connector Short Coax Cable Ethernet Cable to DC Power Injector maximum 300 feet Table 2 1 Recommended External Antennas for the AP Ext N and AP LR Ext N Terabeam Model No A2408 Omnidirectional 16 in 8 dBi gain 2400 2500 MHz A2412 0 Omnidirectional 65 in 12 dBi gain 2400 2485 MHz Omnidirectional 65 in 12 dBi gain 2400 2485 MHz with 3 degree downtilt TAPOO1S Sector 25 5 in 13 dBi gain 2400 2500 MHz Page 5 Jun 2005 AP Ext N User Manual 2 3 DC Power Injector
11. ures Key Features 1 3 802 11b Compatible Ideal for use in campus environments and 802 11b Hot Spots Provides access to any 802 11b compatible client 802 11b radio built right into the flat panel unit LR models feature a built in amplifier and provide the maximum range possible Weatherproof designed and rated for outdoor use Provides extended range coverage by focusing the radio signal Unit and Ethernet cable are designed for outdoor use Unit is lightweight and thin just 1 25 inch thick and 15 5 inches square N type connector in the back for external antenna Transmit power of 15 dBm for standard and 24 dBm for LR model Up to 4 5 Mbps actual throughput DC power for electronics in the antenna are carried up the Ethernet cable Power Over Ethernet POE Windows based Configuration Software Remotely manageable and SNMP compliant Protects against access by unauthorized stations via an Access Control Table or MAC authentication via a RADIUS Server Operating temperature range 20 C to 50 C AP Ext N Kit Each AP Ext N kit includes the following refer to Figure 1 1a Flat panel unit with built in Access Point and N type connector for external antenna LR models feature an integrated bi directional amplifier for increased transmit power and receive signal sensitivity for longer range Sturdy steel wall mast tilt bracket mount Cat 5 DC Power Injector 110 220 VAC to 48 VDC Power Supply CD ROM with Windows based softw
Download Pdf Manuals
Related Search