Home

FA147C Installation Manual

image

Contents

1. This symbol indicates the presence of critical information that if not observed could seriously affect the operation of the system or could cause damage to the system Please read each warning carefully This symbol also denotes warnings about physical harm to the installer Many system options are programmed in an interactive menu mode by responding to Alpha keypad display prompts These prompts are 00 Quit shown in a double line box Enter Zn Num 20 When programming the system data fields are indicated by a star followed by the data field number PRODUCT MODEL NUMBERS Unless noted otherwise references to specific model numbers represent First Alert Professional products SECTION 1 General Description In This Section General Information General Information The FA147C is a control that supports up to 36 zones using basic hard wired wired expansion and or wireless plus remote keypads Basic Hardwired Zones Provides 6 basic hardwired zones having the following characteristics e Zones 1 6 response time is 300 500 milliseconds e Zone 3 programmable for fast response time 10 milliseconds e EOLR supervision supporting N O or N C sensors e Zones 1 6 can be programmed for fire and will support as many 4 wire smoke or heat detectors as can be powered from the control e Zones 95 96 and 99 keypad Panics e Zone 8 Duress e Zone 9 Expansion Module Failure Trouble
2. For programming from a keypad an FA550KP 2 line Alpha keypad must be connected but need not necessarily stay in the system Security Codes e One Master code for entire system user 2 Installer code is user 1 e Up to 5 secondary user codes for users 3 7 If not using a Duress code user code 8 is available for an additional user e One duress code user 8 which when used to disarm or arm the system will send a silent duress message to the central station Keypad Panic Keys e Upto 3 programmable panic key functions are provided designated as Zones 95 96 and 99 e Activated by wired and wireless keypads Paging Feature If the paging feature has been programmed for your system a pager will respond to certain conditions as they occur in your system and display code numbers on the pager indicating the type of condition that has occurred Quick Arm Feature Quick Arm may be programmed allowing use of the key in place of the security code for arming Quick Arm will not work unless the Master code has been programmed into the system Optional Output Relays e Up to 4 relays using one Ademco 4204 Relay Module e Up to 2 relays using one Ademco 4229 Zone Expansion Relay Module e Actions programmable to respond to zone activity or manual keypad entries Optional Phone Module e Supports the FA4285 Phone Module e Provides access to the system via on premises or off premises phones for arming disarming etc
3. If the first zone number entered does not have one or more of the above attributes the system will search its database for the first zone that does and will display it on the next screen 5 This prompt is displayed when the system has found the next zone which needs to be enrolled The system will respond to the first serial number transmitted A serial number may be enrolled by one of two methods a Enter the 7 digit serial number printed on the transmitter or b Activate the transmitter by faulting or restoring the input you wish to use for that zone e g press a button open or close a door etc If you do not wish to enroll the zone displayed press the key on the keypad or the upper right hand button on the program tool a long beep will be heard to verify The following prompt will appear 10 Learn S N 0 No 1 Yes 0 To enroll now enter 1 Yes If 0 No is entered the following prompt will appear if a program tool has already been programmed Enter Zn Num 00 Quit 12 Zone Number Entered Enter the next zone number to be enrolled e g zone 12 The system will search for that zone and will display the prompt shown in the beginning of step 5 If you wish to exit the enroll mode completely enter 00 and press The system will enroll the serial number of the first transmitter heard add the loop number entered to this serial number display the serial and loop numbers and cau
4. soii ini nata tesa ICE LASA REINSERIRE RARA NASA O AAEREN R EE EnG E KOES 9 2 Sounder SUPEL VISION 0622 cis iii ila 9 2 Programming For External Sounders ii 9 2 Testing the Sounders sasie ceccavescaedets Sosktes aiar 9 3 Using the Memory of Alarm Trigger for a Strobe iii 9 3 Long Range Radio g bei leale 10 1 General Information srrerrrsrrr sens rr rr rr RER KKR RER KRK RR ERK RR Brr ren cease 10 1 Wiring Connections srt ili cennad eb kann AA LARA SEK ARRE PALA RAS pec SARE ELAINE RAI E E 10 1 Programming for Long Range Radio i 10 2 Audio Alarm Verification AAV Unit iii 11 1 General Information grata arrendere aiar ritiene riale 11 1 Wiring Connections for a Non Ademco AAV Unit i 11 1 PROS TAMIA Goi iter Ces Sais hte fad NE i PE ee att 11 2 Pinal POWer OD isis ee os eae Si ed Fr edra rer he cece ot ee 12 1 General Information eusen n ae deeds ines wae sito BA A ns 12 1 Earth Ground Connections iii 12 1 AC Powers Wp scicisredists ERE AI i 12 1 Connecting the Back Up Battery ccesesseceeseeeececsesaeceessaae aiai RE 12 1 Calculating the Battery Size Needed ii 12 1 Making the Battery Connections i 12 2 Table of Contents Continued Section 13 Alpha Descriptor PFOGramnMIiNO emmemersrsrrrrrrsrrrrrr srrerrsrsrer are
5. TABLE 1 58811 58821 5881M up to 16 5881H 5882H up to 30 t 5882 type receivers are for use in Canada See special note below Any zone number from 10 39 can be used as a 5800 series wireless zone do not confuse this with the number of zones that can be used which is shown in Table 1 above Wireless may not be used in UL Commercial Burglary installations In Canada 5800 systems must use 5882 series receivers 5882L or 5882H Information relative to the 5881 series of receivers applies as well to the 5882 series 5881 and 5882 series receivers can use the same transmitters 5800 type Wireless System Operation and Transmitter Supervision The receiver responds to status and alarm signals from wireless transmitters operating at 845MHz for 5800 series in USA and Canada within a nominal range of 200 feet the receiver then relays this information to the control Except for transmitters that may be carried off premises such as the 5800 system s 5802 5802CP 5804 5804BD 5827 and 5827BD each transmitter is supervised by a check in signal that is sent to the receiver at 70 90 minute intervals If at least one check in is not received from each supervised transmitter within a 12 hour period the missing transmitter number s and CHECK will be displayed on the keypad 6 1 FA147C Installation Instructions The supervision for a particular transmitter in the 5800 system may be turned off by entering it as
6. The 5800TM must be located between one and two feet from the 5881 receiver s antennas The 5800TM must not be installed within the control cabinet Mount the unit using its accompanying mounting bracket 5800TM Wiring Connections xh Connect the 5800TM to the control panel s keypad connection terminals using the supplied connector with flying leads as follows Wire Terminal On Control RED 12VDC Terminal 5 BLACK Ground Terminal 4 GREEN Data to Control Terminal 6 YELLOW Data from Control Terminal 7 BLUE Not Used Do not cut any of the jumpers on the 5800TM when using it with the FA147C For additional information refer to the 5800TM s instructions Other than the 5827 5827BD and 5804BD 5800 series devices do not communicate by House ID but by transmitting a unique serial number to the control In this case programming a House ID is not necessary Programming the Control For Wireless 1 A two line alpha keypad FA550KP must be connectedand set to address 31 and the system powered up 2 Enter the programming mode by keying Installer Code 8 0 If using a 5800 RF system field 22 must be set to 1 Note If using a 5827 5827BD wireless keypad or 5804BD wireless key you MUST enter an RF House ID in field 24 If these units are not used enter 00 6 3 FA147C Installation Instructions Enrolling 5800 Series Transmitters 5800 series transmitters have built in
7. This is sent when a transmitter that previously sent in a low battery message has sent a message indicating it no longer has a low battery condition Press 84 EVENT LOG 80 FULL REPORT CODE If an Event Logging selection is made in field 85 a message can be sent to the central station receiver when the log is 80 full Note Aside from the selection made by the installer in field 85 all control and readout from the log is accomplished via the Downloader Press 85 EVENT LOGGING 0 No event logging 1 log Alarm Alarm Restore 2 log Trouble Trouble Restore 4 log Bypass Bypass Restore 8 log Open Close x log combination of events add value of entries Example To select Alarm Alarm Restore and Open Close enter 9 1 8 to select all events enter 15 1 2 4 8 The default of 3 alarm alarm restore 1 plus trouble trouble restore 2 Note System messages are logged when any non zero selection is made 93 Press 92 NUMBER OF REPORTS IN ARMED PERIOD This option can be used to limit the number of messages alarm amp alarm restore reports sent to the central station in an armed period 0 allows unlimited reports 1 15 allows reports from 1 to 15 i e 1 allows 1 report 2 allows 2 reports etc PAGER CUSTOM DATA Optional 16 digits for Account numbers PIN numbers or any additional data that you wish to precede the 7 digit status code sent
8. 24 Hr Aux 02 Entry Exit 2 09 Fire 03 Perimeter 10 Interior w Delay 04 Interior Follower 15 24 Hr Medical 05 Trouble Day Alarm Night Personal Emergency 06 24 Hr Silent 23 No Alarm Response Do not use in UL installations When the display shows the zone type you want press to continue Section 5 Wired Expansion Zones The report code consists of 2 hexadecimal digits each in 10 Report Code turn consisting of 2 numerical digits For example for a 1st 03 2nd 12 3C report code of 3C enter 0 3 for 3 and 1 2 for C Refer to the System Communication section for complete information on report codes if necessary Enter the report code and then press to continue 7 At the Input Dev prompt enter 2 AUX Wired as the 10 Input Dev LP input device The display on the left will appear APS Villa ARE O Press to continue Typical summary display A summary display will appear showing the data for the zone that was just programmed Note that AW indicates an Zn ZT RC In L auxiliary wired zone expansion module zone 10 03 3C AW If it is programmed satisfactorily press to display the next prompt For all zone types the next request is to enter Alpha descriptors for the zones The entry may be done now enter 0 No 1 Yes 1 or may be done at a later time using 82 interactive menu mode enter 0 We recommend that the entry of Alpha descriptors be done later us
9. NN UNIT A IF USED Oa Oa DIRECT FOFE CONNECT 5 157 CORD IMPORTANT NOTE FOR 9 19 EXISTING INSTALLATIONS Z Z Ec EXISTING WIRES CON cg 0 PREMISES NECTED TO THE HAND 2393 CA38A IN ANSWERING SET TERMINALS ON THE HO BE PLUG CANADA MACHINE CONTROL MUST BE 2 5 2 amp AND PHONES MOVED FROM THERE TO TERMINALS 3 AND 4 ON ANSWERING THE FA4285 MACHINE BROWN T FA4285 PHONE MODULE NOT INSTALLER 47 ADJUSTABLE 9 KEYED ga i HEADER NOTE IF THE TELEPHONE HAS BUILT IN CALLER ID o THE CALLER ID FUNCTION MAY NOT WORK UNUSED YELLOW TO DATA OUT term 7 TO CONTROL FA4285 NO CONNECTION PANEL TERMINAL ASSIGNMENTS CONNECTOR RED TO AUX term 5 TERMINALS TIP WITH FLYING BLACK TO AUX GROUND term 4 USED FOR RING PHONE INPUT LEADS GREEN TO DATA IN term 6 KEYPAD TIP CONNECTIONS RING PHONE OUTPUT NOT USED AUDIO OUT 1 FOR FUTURE USE 1 2 3 4 5 6 T Figure 8 1 FA4285 Phone Module Wiring Connections FA147C Installation Instructions Programming The Control For Phone Access 1 Atleast one Alpha keypad set to the non addressable mode address 31 must be connected to the control and the system powered up Note The FA4285 has a permanent device address of 4 2 Enter the programming mode by keying the following on the keypad INSTALLER code 8 0 3 Press 26 VOICE PHONE MODULE ACCESS CODE Enter the 2
10. 1 Insert self tapping screws provided in two adjacent raised cabinet tabs Leave the heads projecting 1 8 2 Hang the unit on the screw heads via two of the slotted holes at the rear of its housing as shown in Figure 2 2 3 The 4204 s cover can be left off if the unit s DIP switch is set with its position 1 ON to the right as shown in its instructions The 4219 s or 4229 s cover can be left off if the cover tamper jumper is placed in its upper not tampered position see Detail C The tampered cover is necessary for installations outside of the control s cabinet LITTTTITVITT T7777 LL AD SST Y f f f y 7 DETAIL B SIDE VIEW OF SHORT MOUNTING CLIPS DETAIL A SIDE VIEW OF CONTROL BOARD SUPPORTING SLOTS CIRCUIT BOARD Figure 2 2 Installing the PC Board in the Cabinet Alone or if used with a 4204 4219 or 4229 Section 2 Installing the Control Installing the Control and RF Receiver Circuit Boards Together in the Cabinet Figure 2 3 1 Hang two short black mounting clips provided with receiver on the raised cabinet tabs as shown in Detail B in Figure 2 3 2 Insert the top of the receiver board removed from its own case as described in its instructions into the slots at the top of the cabinet as shown in Detail A in Figure 2 3 Make sure that the board rests on the correct row of tabs as shown 3 Swing the base of the board into the mounting clips and secure it to the cabinet
11. 24 Section 2 Installing the Control Installing The Back Up Battery 1 Place the 12 volt back up battery in the control cabinet To calculate the correct battery size for an installation refer temporarily to Calculating the Battery Size Needed in the Final Power Up section UL Use a 4AH battery or larger for UL installations oh 2 Attach Red and Black wires on the battery connector cable to the control board as follows a Red to the positive battery tab on the control board see Summary of Connections Diagram for location if necessary b Black to the negative battery tab on the control board These wires may have already been connected to the battery tabs on the control board If so disregard steps a and b Do not attach the connector cable to the terminals on the battery until you are instructed to do so later in the manual Earth Ground Connections This product has been designed and laboratory tested to ensure its resistance to damage from generally expected levels of lightning and electrical discharge and does not normally require an earth ground If an earth ground is desired for additional protection in areas of severe electrical activity terminal 21 on the control board or the cabinet may be used as the ground connection point The following are examples of good earth grounds available at most installations Metal Cold Water Pipe Use a non corrosive metal strap copper is r
12. To choose a manual entry of User Code 7 to turn it off we will program ZT as 34 see Choices for System Operation in the table above If no other relay is to be programmed we go to field 81 and program the 3 specific zones in Zone List 1 Section 7 Relay Outputs and X10 Type Module Usage Press 81 Zone Lists for Output Relays This interactive menu mode is applicable only if you have programmed 80 mode Refer to the Programming Form worksheet for 81 Mode in the separate Programming Guide Zone List Displays Upon keying 81 this screen will appear Enter the Zone List Number 01 02 or 03 to program or 00 to end these entries Press the key to advance In the following displays zone list 01 has been selected for programming Enter each zone number to add to the zone list by first entering the zone number then pressing the key example 01 02 03 After all zones desired are entered press 00 to advance To delete the zone list enter 1 Yes All zones in the zone list will be deleted automatically and programming will return to the first screen To save the zone list enter 0 No to advance To delete a zone or zones in a zone list enter 1 Yes to advance 01 Delete Zone 0 No 1 Yes Enter each zone to be deleted from the list followed by the key After all zones to be deleted are entered enter 00 to return to the first screen so that another list can be programmed i
13. desired Note that the key cannot be used in place of code when disarming the system Disarming Enter code OFF 1 Bypassing Zones Enter code BYPASS 6 zone number s Forced Quick Bypass If enabled To automatically bypass all faulted zones use the Quick Bypass method Enter code BYPASS then wait for all open zones to be displayed Arm when display indicates Bypass and Ready to Arm If programmed in field 23 zones 17 30 and 31 will also be bypassed Chime Mode Key the security code CHIME 9 or simply key 9 To turn chime off again repeat the above NOTE If the entry in field 31 is 0 faulting of any entry exit or perimeter zone will cause a chime sound when Chime is on If the entry in this field is 1 only the faulting of specific zones as programmed in field 81 will cause a chime to sound See Programming for Chime By Zone in Section 7 SUMMARY OF ARMING MODES Features for Each Arming Mode Arming Exit Entry Perimeter Interior Mode Delay ee AWAY Yes Yes STAY eee INSTANT MAXIMUM Panic Keys oh There are three individual lettered keys or panic key pairs on some keypads that if programmed can be used to manually initiate alarms and send a report to the central station Each can be individually programmed for 24 hour Silent 24 hour Audible 24 hour Medical
14. stopping some action such as turning lights on or off etc These entries are Security Code 7 and Security Code 4 8 Note Whichever entry is used to start the action cannot also be used to stop it The opposite action must either be performed by the other keypad entry or by some other event or operation offered in the programming section For example if Security Code 4 7 was used to turn a light on this entry cannot then be used to turn the light off you must use Security Code 8 to turn the light off The reverse is also true If a relay is energized before a 4 wire smoke detector is reset the relay will be stopped by the interruption of Aux Power that resets the smoke detector If this is not desired the power to the relay unit should be supplied from another 12V power source e g the same source that is powering external equipment through the relay contacts Section 7 Relay Outputs and X10 Type Module Usage Programming Output Relays 1 At least one 2 line Alpha keypad FA550KP must be connected to the keypad terminals on the control and the system powered up Enter the programming mode by keying the following on the Alpha keypad INSTALLER code 8 0 Program field 25 WIRED EXPANSION RELAY USED must be programmed as required before continuing i e 2 4229 3 4204 Press 80 Note that this is an interactive menu programming mode It is used to program all
15. 0 No 1 Yes CUSTOM ALPHA EDITING enter 0 See the Alpha Descriptor Programming section for specific procedure If 0 no was entered above the system will return to the Enter Zone Enter Zn Num Number prompt Proceed with the programming for the next zone i e 00 Quit and zone number Enter next zone number Programming Panic Keys When programming panic zones note the following The defaults for panic key pairs or individual panic keys are Zone 95 1 amp or A zone type 08 24 Hr Aux Zone 96 3 amp or C zone type 09 Fire Zone 99 amp or B zone type 07 24 hrAudible Panic keys are programmed or re programmed by keying the zone number e g 95 96 or 99 and then entering the desired zone type that will provide the desired panic function for each of these keys using the list of zone types below 06 24 Hr Silent 07 24 Hr Audible 08 24 Hr Aux 09 Fire 15 24 Hr Medical Personal Emergency Do not use in UL installations When you have programmed all the hard wired zones and Panic keys satisfactorily exit 56 interactive mode at the Enter Zn Num prompt by entering 0 0 as the next zone number Then exit the programming mode by keying 99 See the special notes below then proceed to the check out procedure that follows Special Notes on Zone Programming e In field 56 at the summary line for each zone the entered values can be checked
16. 16 zones 1 6 See the Summary of Connections diagram 2 Connect closed circuit devices in series in the high side the loop The EOL resistor must be connected in series with the devices following the last device See the Summary of Connections diagram 3 Connect open circuit devices in parallel across the loop The 1 000 ohm EOLR must be connected across the loop wires at the last device A If the EOLR is not at the end of the loop the zone will not be properly supervised and the system may not respond to an open circuit on the zone Wiring 4 Wire Smoke Combustion Detector To Zones 1 6 The system will support as many 4 wire detectors as can be powered from the Auxiliary Power terminals on the control Refer to the detector s instructions for complete details regarding its proper installation and operation 1 Connect 12 volt power for the detectors from Auxiliary Power terminals 4 and 5 which will interrupt power for fire alarm reset Observe proper polarity when connecting detectors See Figure 4 1 2 Connect detectors including heat detectors if used across the terminals of the selected zone s All detectors must be wired in parallel Zones using heat or smoke detectors must be programmed for Fire 4 1 FA147C Installation Instructions Remove 1000 ohm EOL resistor if connected across zone terminals You must connect the EOL resistor across the loop wires at the last detector 3 You must use
17. 22 to 1 for 5881 RF receiver Set ZT to a valid active zone type in field 56 Install proper battery Enter unit s serial No in field 56 or 83 System battery is low or missing Remote RF wireless keypad battery low Remote RF wireless keypad battery low Transmitter for zone nn has a low battery Enter Code OFF to exit TEST mode Enter Code OFF and replace the battery Check the wireless transmitter indicated Restore communication to the RF receiver to cancel the condition Delete input s serial number not the zone and enter the proper loop input see field 56 or 83 Determine which transmitter is programmed for this zone and re program as necessary 18 1 FA147C Installation Instructions SYSTEM Continued SYMPTOM POSSIBLE CAUSE REMEDY 6a Check installation to see if in accordance with established procedure 6b Check programming for transmitter 6 Nuisance or phantom alarm Sensors not properly installed wired or monitored Universal transmitter 5817 programmed incorrectly 7 Intrusion alarm for no apparent reason Protected door or window opened while system is armed Improper user operation of exit entry delays Magnets located too far from switches and or doors and windows not properly aligned Magnetic contacts improperly connected or wire broken Entry door programmed as Instant Loose fitting door or window being rattled by wind
18. A single long beep will be heard from the keypad to verify pressing of the upper right hand button Then press 1 Yes or press the upper left hand button of the program tool a single short beep will verify the system is ready for enrolling and re activate the proper transmitter or transmitter loop input 7 The system will search for the next zone that does not have a serial number associated with it If one is found the prompt in step 5 along with the appropriate zone number will be displayed Follow steps 5 and 6 for the remaining wireless zones 8 After all wireless zones have been displayed whether enrolled or not the Enter Zn Num prompt will appear Enter 00 to exit the Sequential mode and return to data field programming mode When you have finished programming all zones test each using the system s TEST mode Do not use the Transmitter ID Sniffer mode for this as it will only check for transmission of one zone on a particular transmitter and NOT the zones assigned to each additional loop 14 3 FA147C Installation Instructions 144 SECTION 15 System Communication In This Section General Information Report Code Formats Table of Contact ID Event Codes Communication Programming General Information This section provides an explanation of formats this system accommodates for reporting alarms and other system conditions to the central station The process of a successful transmissio
19. Code Alarm Restore Code Trbl 1st amp 2nd digits Restore Code Byps 1st amp 2nd digits Restore Code AC 1st amp 2nd digits Restore Code Bat 1st amp 2nd digits Ademco Contact ID Reporting takes the following format CCCC Q EEE GG ZZZ where CCCC Customer subscriber ID Q Event qualifier where E new event and R restore EEE Event code 3 hexadecimal digits Note For a complete list of event codes refer to the central office receiver manual GG Always 00 ZZZ Zone contact ID number reporting the alarm or user number for open close reports System status messages AC Loss Walk Test etc contain zeroes in the ZZZ location Section 15 System Communication TABLE OF CONTACT ID EVENT CODES Alarm Medical Personal Emergency Fire Loop Trouble Exit Error Alarm 121 122 123 131 132 134 135 150 301 Trouble Global 383 384 401 406 407 408 416 441 Armed STAY INSTANT Quick Arm STAY INSTANT 302 Low System Battery Battery Test Fail BELL Siren 1 Trouble Expansion Module Fail Long Range Radio Trouble 570 601 606 AAVtofollow Communication Programming Introduction This section provides instructions for programming those fields that affect communications between the control and the central station Programming Procedure 1 At least one Alpha keypad FA550KP must be connected to the system which should be powered up 2 Enter the programming mode by
20. Do not use in UL installations These are special zone types used with 5800 series wireless pushbutton units which will result in arming the system in the STAY or AWAY mode or disarming of the system depending on the selection made A button programmed for these functions will report the zone number of the button as the user number that armed disarmed to the central station This is a special zone type used with 5800 series wireless pushbutton units which can be used on a zone when an output relay action is desired but with no accompanying alarm e g lobby door access Zone Number 10 Zone Type Perimeter 03 Entry for Zone Type 03 shown as an example After entry of zone type press to continue 7 10 11 Section 6 Wireless RF Zone Expansion 5800 RF Systems Enter the report code The report code consists of 2 hexadecimal digits each in turn consisting of 2 numerical digits For example for a report code of 3C enter 0 3 for 3 and 1 2 for C Refer to the System Communication section for more information about report codes and report code formats 10 Report Code 1st 03 2nd12 3C Press to continue 10 Input Dev LP Rf Trans RF 1 Device Type Enter the transmitter input device type as follows 8 RF supervised RF transmitter 4 UR unsupervised RF transmitter 5 BR button type RF transmitter unsupervised Information about transmitter input types
21. IN 2908 A DATA TERM 7 uo Oo z 3 CONTROL RLY TAMPER TERMINATE EACH PROGRAMMED ZONE WITH 1000 OHM END OF LINE RESISTOR EACH ZONE S MAX LOOP RESISTANCE 300 OHMS E O L SWITCH Figure 7 2 4229 Connections to Control Using an X10 Type Module An X10 type module PF284 or equivalent can be used with the FA147C system to enable you to control lights or other devices connected on the same AC power line A keyed connector with flying leads has been supplied for connection of the X10 type module to the X10 trigger on the control board as shown in Figure 7 3 Use only the BLACK and YELLOW flying leads for connection to the X10 type module as follows Yellow lead to the terminal on the PF284 module Black lead to the terminal on the PF284 module The Red and Green leads on the connector are unused and can be cut back and taped Set the PF284 module to INPUT A and MODE 1 The required programming when using an X10 type module is provided at the end of this section See Programming For an X10 Type Module 7 2 Section 7 Relay Outputs and X10 Type Module Usage ALL UNITS OFF VAY M E a I N UNIT CODE HOUSE CODE SET TO X 10 INPUT A PF284 MODE 1 USE KEYED CONNECTOR SUPPLIED TO X10 fa cor Figure 7 3 dii NOT USED Connecting an XI 0 Type BOARD PF284 shown FLYING LEADS Programming Options Defined The following will help you understand the programming
22. If you wish to change anything press 4 to move to the previous entry Press a number of times to move to earlier entries Press to move to later entries again e Zone entries can be reviewed by pressing 5 6 Changes cannot be made here so this is safer for review Enter the first zone number to be viewed and press To view each zone press and the zone number will advance to the next programmed zone When the end of the list is reached press 0 0 to exit This method of exiting may also be done at any time during the review Section 4 Basic Hard Wired Zones 1 6 e To either temporarily or permanently remove a zone from the system go into programming mode and press 5 6 Enter the zone number and press At the Zone Type prompt enter 0 0 and This sets the type of the zone to Not Used The next prompt will be Delete Zone Yes will permanently remove the zone from the system while No will disable it but retain all data except the original zone type You can then go back to this zone later and put back an active Zone Type to re enable it Check Out Procedure For Basic Hard Wired Zones 1 6 After installation and wiring of all basic hard wired devices is completed the system should be checked as follows 1 Make certain that all devices and sensors connected to the hard wired zones are not in a faulted state Doors and windows with contacts should be closed PIRs should be covered us
23. Phone Module section for information regarding phone line connections which are A The wiring connections shown here are not applicable if the FA4285 Phone Module is used Refer different than those shown here Incoming phone line and handset wiring is connected to the main terminal block via a RJ31X jack CA38A jack in Canada as indicated below and shown in Figure 2 4 Term 17 Local Handset TIP Brown Term 18 Local Handset RING Gray Term 19 Incoming Phone Line TIP Green Term 20 Incoming Phone Line RING Red Colors of wires in Direct Connect Cord Incoming Handset Telco Line TERMINALS ON CONTROL EARTH GROUND INCOMING TELCO LINE N N GROUND RING a DIRECT FE CONNECT CORD RJZIX TIP JACK PREMISES CA38A PHONES JACK IN PLUG CANADA Figure 2 4 Standard Telephone Line Connections Wiring The AC Transformer 1317 Transformer Wire the transformer to terminals 1 and 2 on the control board See the wiring table below for WIRING TABLE Distance of Transformer From the Control Panel To Use wire gauge to use Up to 50 feet 20 50 100 feet 18 100 250 feet 16 A e Wiring to the AC Transformer must not exceed 250 feet using 16 gauge wire Do not plug the transformer into the AC outlet until you are instructed to do so As a general rule the control should be de powered while making any connections to it
24. SI 17 2 Keypad Functions ita 17 2 General Informations sanre Da ITA 17 2 Arming Disarming Functions etc i 17 3 Panic Keys S EE yous aa oboe rails 17 3 FA4285 Phone Module if USEd ii 17 4 Relays Outputs Gf used Ai ail long ane 17 4 Exit Alarm Displays if programmed i 17 4 Prouble COnditiOS s sssiveissvevasosb ssvss eni aa 17 4 General Information aria arl rio 17 4 Check and Battery DisplayS ii 17 5 Power Failures asfissia te R te RE E oa Ene IEEE eE Ee EEEE EaR Eok 17 5 Other Displays 2000 ciali RA AR KRA NAS ra eb eldest Me es 17 5 Section 18 Troubleshooting Guide ii 18 1 General Information iii 18 1 Troubleshooting Chait ocon ano ai e a lalla ie Gain HAR KRKA SAD ann 18 1 Contacting Technical Support ii 18 3 Section 19 Specifications amp AccessorieS ii 19 1 Specie OS eotie ei TEEL EE EEO EKETE eiA seabed ALA EEC EEEE IR ca 19 1 Accessories Compatible Devices iii 19 3 Section 20 Regulatory Agency StatementS iii 20 1 Appendix A Limitations Of This Alarm System meseeseserrrrsrsrsrsrsrer snserrrrrrrerrrsrsrrnn nn nn nn rna A 1 Appendix B FA147C Summary Of Connections Diagram Inside Back Cover B 1 Limited Warranty ss sballo hater aten atta caste i Sarees
25. a UR unsupervised RF type as described later 5800 series transmitters have built in tamper protection and will cause a CHECK condition to be annunciated if covers are removed Each transmitter is also supervised for low battery and will transmit a low battery signal to its receiver with the battery having at least 30 days of life remaining A low battery message and appropriate zone number will appear on a wired keypad s display Ifa 5827 or 5827BD wireless keypad has a low battery it will be displayed as Zone 00 when it transmits Note After a low or dead battery is replaced activate the transmitter and then enter the security code OFF to clear the system s memory of the Low Battery signal Transmitter Battery Life e Batteries in the wireless transmitters may last from 4 7 years depending on the environment usage and the specific wireless device being used External factors such as humidity high or low temperatures as well as large swings in temperature may all reduce the actual battery life in a given installation The wireless system can identify a true low battery situation thus allowing the installing company or user of the system time to arrange for a change of battery and thus maintain protection for that given point within the system e Some transmitters e g 5802 5802CP contain long life but non replaceable batteries At the end of their life the complete unit must be replaced and a new ser
26. a transmitter 6 7 FA147C Installation Instructions Pressing the 4 key on the keypad will cause the system to back up to the Program Tool prompt The serial number for the program tool will only remain in the system until the programming mode is exited Entering 97 will not delete the tool Press to continue 4 Enter the zone number that you wish to program As an example zone 10 is shown below Enter Zn Num 00 Quit Zone 10 entered Press to continue 5 A display will appear showing a summary of that zone s programming If the zone is not programmed the display will appear as shown below If checking a zone s programming and it is programmed satisfactorily press to back up one step and enter the next zone number as desired Otherwise press to continue ZN ZT RC In L 10 00 00 RF 1 6 Each zone must be assigned a zone type which defines the way in which the system responds to faults in that zone Enter the zone type desired or change it if necessary Available zone types are listed below 00 Zone Not Used 08 24 Hr Aux 01 Entry Exit 1 Burglary 09 Fire 02 Entry Exit 2 Burglary 10 Interior w Delay 03 Perimeter 15 24 Hr Medical Personal Emergency 04 Interior Follower 20 Arm Stay 05 Trouble Day Alarm Night 21 Arm Away 06 24 Hr Silent 22 Disarm 07 24 Hr Audible 23 No Alarm Response e g Relay activation
27. digit phone access code as follows For the first digit enter 1 9 for the second digit enter 11 for or 12 for 4 Example if desired access code is 7 7 is the first entry and 11 for is the second entry Enter 00 if not using a Phone Module this is the default Note A 0 in either digit will disable a Phone Module 4 Press 95 RING DETECTION COUNT FOR DOWNLOADING Refer to the chart below and program this field accordingly access the Phone Module included in the installation you should note the following No Set for a value higher than the number of rings for which the answering machine is set Example if the machine is set for 4 rings use a value of 5 or higher This is recommended so that the Phone Module can still be es When calling in from an off premises phone to receive a status report or execute a command accessed if the answering machine is turned the user should make the initial call allow 1 to 3 rings only and hang up Then call in again Phone Answering Module Machine Downloading Field 95 Programming Yes No Set for value other than 0 1 14 This will enable the control panel to answer the phone call Otherwise it will not be possible to Yes Yes off and does not answer the phone call Set for value other than 0 1 14 Yes Yes Y Enter 15 to bypass the answering machine See Important Note below Important Note If 15 is entere
28. door Also an alarm in the hallway outside may not wake up the sleeper if the door is closed e Install a smoke detector inside bedrooms where electrical appliances such as portable heaters air conditioners or humidifiers are used e Install a smoke detector at both ends of a hallway if the hallway is more than 40 feet 12 meters long e Install smoke detectors in any room where an alarm control is located or in any room where alarm control connections to an AC source or phone lines are made If detectors are not so located a fire within the room could prevent the control from reporting a fire or an intrusion Da ba a Tv Room KITCHEN DINING DI DINING LIVING ROOM BEDROOM LIVING ROOM BEDROOM IB Smoke Detectors for Minimum Protection Smoke Detectors for Additional Protection A Heat Activated Detectors BEDROOM DI Di TO BEDROOM BEDROOM _ THIS CONTROL COMPLIES WITH NFPA REQUIREMENTS FOR TEMPORAL PULSE SOUNDING FOR FIRE NOTIFICATION APPLIANCES A GARAGE LOSED OOR Recommendations For Proper Intrusion Protection For proper intrusion coverage sensors should be located at every possible point of entry to a home or commercial premises This would include any skylights that may be present and the upper windows in a multi level building In addition we recommend that radio backup be used in a security system so that alarm signals can st
29. for each FORMAT HANDSHAKE TRANSMITS DATA KISSOFF TRANSMIT TIME 4 2 Ademco 1400Hz 1900Hz 10PPS 1400Hz Under 15 secs Low Speed Standard report 4 2 2300Hz 1800Hz 20PPS 2300Hz Under 10 secs Radionics Standard report 4 2 Ademco 1400 2300Hz DTMF 10 cps 1400Hz Under 3 secs Express Ademco 1400 2300Hz DTMF 10 cps 1400Hz Under 3 secs Contact ID The following describes each format in greater detail 4 2 Format Comprises a 4 digit subscriber number and 2 digit report code Ademco Contact ID Comprises a 4 digit subscriber number 1 digit event qualifier Reporting Format new or restore 3 digit event code and 3 digit zone number user number or system status number see the following page FA147C Installation Instructions Where 4 2 Reporting SSSS AZ SSSS OU SSSS CU SSSS Gg SSSS RZ sassi Ag Trouble Res SSSS Rpt SSSS Subscriber ID A Alarm Code lst digit Z Typically Zone Number 2nd digit Gg Tt Trouble Code 1st amp 2nd digits Bb Bypass Code 1st amp 2nd digits Rt EAc AC Loss Code Ist amp 2nd digits Rpb LLp Low Battery Code 1st amp 2nd digits RaAc O Open Code 1st Digit RLLB Zone numbers for 1 or A 95 3 or C 96 x amp or B 99 Duress 8 Tamper 9 Expansion Module Failure also Close Code 1st Digit User Number in hex Test Code 1st amp 2nd digits Restore
30. has been enrolled regardless of whether or not the enrolled input has been confirmed If the incorrect transmitter has been enrolled press the key on the keypad or the upper right hand button of the program tool to delete the serial number and return to the Learn S N prompt A single long beep will be heard from the keypad to verify pressing of the upper right hand button Then press 1 Yes or press the upper left hand button of the program tool a single short beep will verify the system is ready for enrolling and re activate the proper transmitter or transmitter loop input ZN ZT RC IN L 10 03 3C RF 1s The summary screen for the zone will appear Note that an s indicates that a serial number has in fact been enrolled The cursor will be flashing above the loop number Press to accept the zone information Note If you entered 0 in step 10 previously you will not get an indication that the serial number has been enrolled If you want to delete the serial number enter 0 and press The system will then prompt Delete S N Press the 1 Yes key to complete the delete sequence This process deletes the serial number only not the loop number The assumption is that the proper loop number was programmed but the wrong serial or loop number was enrolled To change the loop number you must go back through zone programming for that zone and manually enter the loop number over the existing one After
31. message and produce one short tone Check the keypad initiated alarms that have been programmed in the system by pressing the Panic key key pairs on some keypads If the system has been programmed for audible emergency the keypad will emit a steady alarm sound and ALARM and zone number will be displayed Silence the alarm by entering the security code and then pressing OFF If the system has been programmed for silent emergency there will be no audible alarms or displays but a report will be sent to the central station If output relay units have been installed test their programmed action Notify the central station when all tests are finished and verify results with them FA147C Installation Instructions 8 To test the wireless part of the system and the RF Receiver perform the two tests Transmitter Sniffer Mode and Go NoGo Test Mode that follow a TRANSMITTER SNIFFER MODE Make sure the system is disarmed before trying to enter this mode Press INSTALLER code 3 This initiates a procedure that will check that all transmitters have been properly programmed Note If the communicator is in the process of sending a report to the central station the system will not go into the Sniffer mode If so wait a few minutes and try again The keypad will display all zone numbers of wireless units programmed into the system As the system receives a signal from each of the transmitters the zone number of that transmitt
32. of OUTPUT RELAYS when using 80 and 81 interactive menu modes The options used to start and stop relays are described below followed by the actual screen prompts and available entries The letter s in parentheses after each function described below such as A after ACTION are those that appear in the various summary displays of programmed data during programming ACTION A The ACTION of the relay is how the relay will respond when it is activated by the START programming You may want the relay to activate momentarily to pulse on and off continuously or to remain activated until some other event occurs to stop it There are four different choices of actions e Activate for 2 seconds and then reset Relay Action A 1 e Activate and remain activated until stopped by some other event Relay Action A 2 e Pulse On And Off until stopped by some other event Relay Action A 3 e Not used when the relay is not used Relay Action A 0 START STT The START programming determines when and under what conditions the relay will be activated The following START options are available A 1 EVENT EV is the condition Alarm Fault Trouble that must occur to a zone or group of zones zone list in order to activate the relay These conditions apply only when a zone list is used The different choices for EVENT are listed below and in the Programming Output Relays section that follows e ALARM Relay act
33. on the keypad lines Exit the programming mode by keying 99 SECTION 11 Audio Alarm Verification AAV Unit In This Section General Information Wiring Connections Programming General Information An Audio Alarm Verification AAV module is an add on accessory that permits voice dialog between an operator at a central station and a person at the alarm installation for the purpose of alarm verification For UL installations the AAV option cannot be used AAV should not be used when Paging or Alarm Reports are being sent to a Secondary number If this is done the call to the Secondary number by the communicator after the alarm report will prevent the AAV from taking control of the telephone line and the AAV Listen in session cannot take place IL Alarm reports must be programmed for the primary phone number to enable this feature After all messages have been sent during a reporting session to the primary phone number the control will trigger the AAV if at least one of the messages was an alarm report If Contact ID format is selected for the primary phone number the control will send a listen in to follow message event code 606 which signals the 685 receiver at the central station to hold the phone connection for 1 minute Once the digital message is kissed off the control will give up the phone line to the AAV module without breaking connection with the central station At this t
34. or 3 If not used enter 0 Press the key to continue If a zone type or system operation will be used to START the relay action enter the appropriate two digit code see table that follows If not enter 00 Press the key to continue 7 5 FA147C Installation Instructions 7 6 CHOICES FOR ZONE TYPES 00 Not Used 04 Interior Follower 08 24 Hr Aux 01 Entry Exit 1 05 Trouble Day Alarm Night 09 Fire 02 Entry Exit 2 06 24 Hr Silent 10 Interior w Delay 03 Perimeter 07 24 Hr Audible 15 24 Hr Medical Personal Emergency Do not use in UL installations CHOICES FOR SYSTEM OPERATION 20 Arming Stay 33 Any Burglary Alarm 39 Any Fire Alarm 21 Arming Away 34 Code 7 Key Entry 40 Bypassing 22 Disarming 35 Code 8 Key Entry 41 AC Power Failure 31 Endof Exit Time 36 At Bell Timeout 42 System Batt Low 32 Start of Entry Time 38 Chime 58 Duress Or at Disarming whichever occurs earlier If a zone list will be used to STOP or restore the relay action enter the zone list ZL number 1 2 or 3 to be programmed in 81 mode If not used enter 0 Press the key to continue If a zone type or system operation will be used to STOP the relay action enter the appropriate two digit code see the Zone Type choices listed above If not enter 00 Press the key to continue This screen again displays a summary of the current
35. relay START programming Press the key to continue 02 A EV ZL ZT STT 0 0 0 00 This screen again displays a summary of the current relay STOP programming 02 A EV ZL ZT STP 0 00 Press the key to continue The display then returns again to the first screen so that the next relay number to be programmed can be entered or enter 0 0 to end relay programming number is chosen press to go to the next screens This is a review mode Previously entered data can be reviewed by pressing 8 0 After the relay only and data cannot be changed Example of Output Relay Programming A light is to be turned on when any one of 3 specific zones are faulted or when any 24 hour auxiliary zone is disturbed We want to turn off the lamp manually without affecting the arming status of the system In field 80 we choose Output Relay 01 and program the Action A to be 2 Close and stay closed The Event we are looking for to start the relay action is a fault so we will program 2 in EV We will use Zone List 1 for the 3 specific zones so we will program 1 in ZL and we will program these 3 zones in field 81 s Zone List 1 The second condition for turning on the indicator is triggering a 24 hour aux zone Zone Type 08 so we will program ZT as 08 To stop relay action and turn off the indicator we do not want to use a restore of any zone so we will program a 0 for the Restore of Zone List ZL
36. serial numbers that must be entered into the system using the 56 or 83 interactive menu mode or input to the control via the downloader The 5800 series transmitters except 5827 described separately do not have DIP switches The procedure for enrolling transmitters into the system in the 56 mode will be found later in this section Enrolling Through Zone Programming 5800 Series Transmitter Input Loops UL xh Each transmitter s zone number is programmed into the system in 56 mode Some transmitters such as the 5816 and 5817 can support more than one zone referred to as loops or inputs On the 5816 for example the wire connection terminal block is loop 1 the reed contact is loop 2 Each loop must be assigned a different zone number and entered separately For button transmitters wireless keys such as the 5804 you must assign a unique zone number to each individual button used on the transmitter Each button on the transmitter also has a pre designated loop or input number which is displayed when entered Refer to 5800 Series Transmitter Input Loop Identification in the separate Programming Guide The 5816 and 5817 do not supervise their loop wiring for shorts Therefore for UL Household Burglary installations the loop wiring may not exceed 3 feet Programming an RF House ID 01 81 in field 24 is necessary only if using 5827 or 5827BD wireless keypads and or a 5804BD wireless key An RF House I
37. that service has been provided The Duress code may be any 4 digit code assigned to User Number 8 To program a Duress code enter Master Code CODE 8 8 desired 4 digit Duress Code The keypad will beep once to confirm acceptance Note The Duress code must differ from the Master Code or any other User s Code To change the Duress code enter Master Code 8 8 new 4 digit Duress Code When the keypad beeps once it signifies that the code has been changed To delete the Duress code enter Master Code 8 8 and wait When the keypad beeps once it signifies that the code has been deleted Keypad Functions 17 2 General Information Note that if you enabled QUICK ARM field 21 the key can be pressed instead of entering the security code for any of the arming procedures Away Stay Instant Maximum etc The security code is always required however when disarming the system Note The Quick Arm feature will function only if the Master Code has been programmed see Assigning the Master Code on the previous page The keypad allows the user to arm and disarm the system and perform other system functions such as bypassing zones and display zone descriptors Zone and system conditions alarm trouble bypass are displayed in the Display Window When an alarm occurs keypad sounding and external sounding will occur and the zone s in alarm will be displayed on the keypad Pr
38. the Memory of Alarm Trigger for a Strobe seeceeeeesseeeeees 9 3 Long Range Radio Connections iii 10 1 Using the Memory of Alarm Voltage Trigger With Long Range Radio 10 1 FA147C Summary of Connections Diagram Inside Back Cover B 1 How To Use This Manual This manual is written to accommodate both the new and the experienced installer of First Alert Professional products A general description of the entire system is located in the first section of this manual This includes the various features available and the optional peripheral devices that the system can support This manual is divided into separate sections A section covering the hardwired zones 1 6 provides complete information on the capabilities of each basic hardwired zone including its usage programming and a checkout procedure Separate sections are also provided for each peripheral device that can be used in the system and includes wiring setup programming requirements and a checkout procedure for that device The checkout procedures ensure that the specific device is operational in the system before proceeding to the next section This sectional arrangement is also particularly useful if you are making an addition to the system at a later time e g adding Wireless zones adding an FA4285 Phone Module etc Without an understanding of the programming method for this system you will not be abl
39. volt siren driver built in and weatherproof for outdoor use Can be wired for either a steady or warble sound 117dB 10 feet 1500mA current draw Ademco 719 2 Channel Siren Self contained 6 12 volt siren driver built in Steady or warble sound 109dB 10 feet 550mA current draw Ademco 747 Indoor Siren Self contained 6 15 volt siren driver built in for indoor wall mount 747F available for flush mounting 105dB 10 feet 400mA current draw Ademco 747UL Indoor Siren Self contained 6 15 volt siren driver built in for indoor wall mount UL Listed 85dB 10 feet 320mA current draw Ademco 744 Siren Driver 6 jumper selected sound outputs Rated at 119dB with use of an 8 ohm 30 watt speaker 1 3 amps current draw Ademco 745X3 Voice Siren Driver Requires special power wiring using additional components 12 volt voice siren driver with English Spanish and French voice messages Separate messages for Fire and Burglary Use with 8 ohm speaker UL Listed 1100mA current draw Ademco 705 820 5 inch Round Speaker 20 watt 8 ohm indoor or outdoor speaker Requires a driver Ademco 713 Speaker 40 watt 8 ohm indoor outdoor speaker Requires a driver System Sensor PA400B beige PA400R red Indoor Piezo Sounder Indoor piezo sounder red or beige rated at 90 dB 10 feet UL Use only UL Listed sounding devices for UL installations The total cur
40. will be displayed The procedure for adding custom words to the built in vocabulary will be found later under Adding Custom Words Note that no entries can be made Entries can be made only when the display contains a flashing cursor which signifies the entry mode 5 To delete or change the default descriptor for zone 1 press plus the same zone number 01 This will clear that descriptor and gain access to the entry mode with flashing cursor allowing changes to be made Note If you do not wish to change the existing descriptor for zone 1 enter plus the next zone number for which you wish to enter or check a descriptor A summary display for that zone will appear You must then press plus the same zone number again to gain access to the entry mode flashing cursor for that zone 6 Press plus the 3 digit number for the first word using the ALPHA VOCABULARY LIST on a following page to locate the desired word and its 3 digit number Example The descriptor that we wish to enter for zone 1 is BACK DOOR From the list BACK 013 Therefore you would enter 0 1 3 Note If you accidentally enter the wrong word simply press plus the correct 3 digit number for the word you want 7 Press 6 to accept the selected word and continue Note If this is the only word you are using for the descriptor press 8 instead of 6 to save that word in memory and then go to step 1
41. with the accompanying screws see Detail B in Fig 2 3 4 Insert the top of the control s board into the slot in the clips and position two long red clips at the lower edge of the board see Detail C 5 Swing this board into place and secure it with two additional screws 6 Insert grounding lugs supplied with the receiver through the top of the cabinet into the left hand terminals of the antenna blocks at the upper edge of the receiver board and secure them to the cabinet top with the screws provided as shown in Detail D 7 Insert the receiver s antennas through the top of the cabinet into the blocks right hand terminals and tighten the screws 8 Setup and wiring of the receiver is contained in the Wireless RF Zone Expansion 5800 RF Systems section HOLES FOR ANTENNAS AND GROUNDING LUGS LEONE SUPPORTING SLOTS APS RECEIVER CIRCUIT BOARD CIRCUIT BOARD CABINET DETAIL A SIDE VIEW OF BOARD SUPPORTING SLOTS SHORT MOUNTING CLIPS CONTROL CIRCUIT BOARD LONG MOUNTING CLIPS ok Il TT DETAIL B SIDE VIEW OF SHORT MOUNTING CLIPS SCREW sy Hac ANTENNA DETAIL C GROUNDING LUG SIDE VIEW OF RN LONG MOUNTING CLIPS i f DETAIL D ANTENNA AND GROUNDING LUG INSTALLATION Figure 2 3 Installing The PC Board And RF Receiver if used Together In The Cabinet RCVR BOARD Reg FA147C Installation Instructions Standard Phone Line Connections to the FA4285
42. zone list enter 1 Yes All zones in the zone list will be deleted automatically and programming will return to the first screen 0 No 1 Yes 01 To save the zone list enter 0 No which will advance you to the next screen 03 Del Zn List If you wish to delete a zone or zones in a zone list enter 1 Yes This will 03 Delete Zone advance you to the next screen Otherwise enter 0 0 No 1 Yes If you entered 1 in the previous prompt this screen will appear Enter each zone to be deleted from the list followed by the key After all zones to be 03 Zn to Delete 00 Quit O deleted are entered key 00 to return to the first screen NOTES e Zone list 3 may include any number of zones e Ifyou only want to review what has been programmed previously enter 8 1 The review can be advanced by using the gt key No programmed values can be changed in this mode When finished enter 0 0 to quit When you have entered all the desired chime zones exit the programming mode by keying 99 SECTION 8 FA4285 Phone Module In This Section General Information Mounting the FA4285 Phone Module Phone Module Wiring Caller ID Units Programming The Control For Phone Access Checking the Operation of the FA4285 Phone Module General Information xh UL The FA4285 Phone Module is an add on accessory for the FA147C that permits access to the secu
43. 1 8 Enter the 3 digit number for the next word In our example the word is DOOR whose number is 057 Enter 0 5 7 The display on the left will appear ZN 01 BACK DOOR t Flashing Cursor if 6 is pressed system ready for next word Default Descriptor amp ZN02 ZONE 02 Program Alpha 0 No 1 Yes 00 Alpha Pgm 82 10 11 12 13 14 Section 13 Alpha Descriptor Programming Press 6 to accept the selected word Note If these are the only words you are using for the descriptor press 8 instead of 6 to save them in memory The two words in our example have now been entered Note however that up to three words may be entered provided the number of characters will fit on the screen Press 8 to save all words in memory The flashing cursor will disappear indicating that the word s are stored in memory for that zone as shown in the display at the left To enter a descriptor for the next zone press plus the desired zone number e g 02 The summary display for the next zone will appear Now repeat steps 6 through 10 for the descriptor for the next zone To exit the Alpha descriptor mode press 00 at the summary display The Program Alpha prompt will be displayed Press 0 This will be displayed Press 99 to exit the programming mode Adding Custom Words will not be annunciated by FA428
44. 35 F 57 C heat detector SECTION 20 Regulatory Agency Statements In This Section FCC Part 15 Statement FCC Part 68 Statement UL Notices California State Fire Marshal CSFM 24 Hour Battery Back Up Requirements Canadian Department of Communications DOT Statement Federal Communications Commission FCC Part 15 Statement This equipment has been tested to FCC requirements and has been found acceptable for use The FCC requires the following statement for your information This equipment generates and uses radio frequency energy and if not installed and used properly that is in strict accordance with the manufacturer s instructions may cause interference to radio and television reception It has been type tested and found to comply with the limits for a Class B computing device in accordance with the specifications in Part 15 of FCC Rules which are designed to provide reasonable protection against such interference in a residential installation However there is no guarantee that interference will not occur in a particular installation If this equipment does cause interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e If using an indoor antenna have a quality outdoor antenna installed e Reorient the receiving antenna until interference is reduced or elimin
45. 4111 As a safety feature there is a 3 try limit in which to enter each code phone code and system code after which time the call in will be aborted Also if no keys are pressed for a period of 20 seconds the call in will be aborted Annunciation of a system status report will start if both codes were entered correctly During any pause in the status report or immediately following it the caller should key the following via the keypad on the phone INSTALLER Code then 1 OFF A beep should be heard and from a wired keypad on the premises and the words DISARMED READY TO ARM or DISARMED NOT READY TO ARM should be heard on the caller s phone indicating that the command was entered successfully DISARMED NOT READY TO ARM would indicate an open zone At this point the caller can hang up the phone Verify with the caller that there was successful access to the system and that the appropriate annunciations were heard over the phone 8 5 FA147C Installation Instructions SECTION 9 External Sounders In This Section Compatible Souders Sounder Connections Programming For External Sounders Testing the Sounder Compatible Sounders Ademco AB 12M 10 Motorized Bell amp Box Motor bell amp box UL Grade A 100mA current draw Ademco 1011BE12M 10 Motorized Bell amp Box Motor bell amp box UL Listed 100mA current draw Ademco 702 Outdoor Siren Self contained 6 12
46. 5 Phone Module You can add up to five installer defined words to the built in Alpha vocabulary Each of the five words can actually consist of a word string of one or more words but no more than ten characters can be used for each word or word string 1 Perform steps 1 2 and 3 of Programming the Descriptors on a previous page Select CUSTOM WORD mode enter 1 when the prompt CUSTOM WORDS is displayed 2 Enter the number 01 10 of the custom word or word string to be created For example if you are creating the first custom word or word string enter 01 for the second enter 02 etc A cursor will now appear at the beginning of the second line Entering the custom word s characters can now be performed Refer to the CHARACTER ASCID LIST of letters numbers and symbols on a following page for the desired character and its 2 digit number functions When adding Custom Words in steps 3 6 the keypad s keys perform the following 4 Moves cursor one space to left 6 Selects desired letter moves cursor one space to right 8 Saves the new word in the system s memory 13 3 FA147C Installation Instructions 13 4 3 Press the key followed by the two digit entry for the first letter you would like to display e g 6 5 for A 4 When you have entered the 2 digit number press 6 to select it The cursor will then move to the right in position for the next character 5 Repea
47. C transformer to de power the control while other connections are being made to the control e g for hard wired zones etc 3 3 FA147C Installation Instructions 3 4 SECTION 4 Basic Hard Wired Zones 1 6 In This Section General Information Installing the Hard Wired Zones Wiring Burglary and Panic Devices To Zones 1 6 Wiring 4 Wire Smoke Combustion Detectors Programming Hard Wired Zones Check Out Procedure For Basic Hard Wired Zones 1 6 General Information This section provides general information for the hard wired zones in the system plus specific instructions for installing 4 wire smoke combustion detectors Also included is a procedure for programming the hard wired zones Make sure the control is not powered up while making connections Installing the Hard Wired Zones Common Characteristics for Zones 1 6 e Response time from 400 milliseconds nominal e Zone 3 can be programmed in field 52 for normally closed sensor fast response 10 msec max to an open suitable for vibration type contacts Default response is 400 msec nominal which should be used for most standard contacts e EOLR supervised zones supporting both open circuit and closed circuit devices e As many 4 wire smoke detectors as can be powered from AUX POWER on the control using zones 1 6 if programmed for fire Wiring Burglary and Panic Devices To Zones 1 6 1 Connect sensors contacts to the hard wired zone terminals 8
48. Comm CC The system is in communication with the central station for change of function or status verification Comm Failure FC A communication failure has occurred Open Circuit OC The keypad is not receiving signals from the control and sees an open circuit Long Rng Trbl bF Back up LRR communication failure 17 5 FA147C Installation Instructions 17 6 SECTION 18 Trouble shooting Guide In This Section General Information Troubleshootin Chart Contacting Technical Support General Information This section contains a troubleshooting chart listing some of the more common trouble symptoms that may be encountered in the system following installation their possible cause and remedy Trouble shooting Chart SYSTEM including Wireless SYMPTOM POSSIBLE CAUSE REMEDY 1 Transmitter signal not received at 5881 Transmitter zone number appears during Transmitter Sniffer mode but does not clear Low Battery message on keypad Periodic beep s from keypad With 5800 RF System no response to a transmitter in normal operation although zone number clears during Transmitter Sniffer mode Transmitter or 5881 not properly powered If Transmitter is 5827 5827BD or 5804BD house ID code not set in field 24 or transmitter not set to same house code set in that field Transmitter located too far from 5881 Metal shielding between transmitter and 5881 Transmitter malfunctioning 5881 malfu
49. D is not necessary for other 5800 series transmitters and the entry should be left at OO default in those cases 5800 Series Transmitter Input Types All of the transmitters described have one or more unique factory assigned loop inputs Each of the inputs requires its own programming zone e g a 5804 s four button inputs require four programming zones Transmitters can be entered into the system as one of the following input device types RE Sends periodic check in signals as well as fault restore Supervised RF and low battery signals The transmitter must remain within the receiver s range UR Sends all the signals that the RF type does but the Unsupervised RF control does not supervise the check in signals The transmitter may therefore be carried off premises BR These send only fault signals They do not send Unsupervised Button RF low battery signals until they are activated The transmitter may be carried off premises Do not install batteries in wireless transmitters until ready to use as will be indicated under Programming the RF Transmitters 5800 RF Systems later in this section Though it is not critical to remove batteries after entering into the system it is recommended in order to avoid interference while entering additional transmitters into the system Section 6 Wireless RF Zone Expansion 5800 RF Systems Compatible 5800 Series Transmitters Enter As Input Product Dev
50. Delete some zones or if RF use a higher capability RF receiver 4d Keypad address setting incorrect Keypads must be set for address 31 non addressable mode SMOKE DETECTOR 1 Detector alarms no ta Dust dirt in sensing chamber Clean unit s sensing chamber with apparent reason vacuum cleaner per unit s instructions 1b Improper location See unit s instructions for locations to avoid Relocate as necessary ic Unit malfunctioning Replace detector 2 Detector s siren sounds 2a Unit not receiving required power 2a Check for proper installation of battery Try new battery 2b Unit malfunctioning 2b Replace detector CONTACTING TECHNICAL SUPPORT PLEASE Before you call Technical Support be sure you e READ THE INSTRUCTIONS e Check all wiring connections e Determine that the power supply and or backup battery are supplying proper voltages e Verify your programming information where applicable e Note the proper model number of this product and the version level NXXXX number on large circuit module in center of control board along with any documentation that came with the product e Note your FIRST ALERT customer number and or company name Having this information handy will make it easier for us to serve you quickly and effectively You may contact Technical Support via Toll Free FAX Please include your return FAX number You will receive a reply within 24 hours You may also contact T
51. EAST ELECTRIC EMERGENCY ENTRY EQUIPMENT EXIT EXTERIOR F FACTORY FAMILY FATHERS FENCE FIRE FLOOR FLOW FOIL FOYER FREEZER FRONT Ga GARAGE GAS GATE GLASS GUEST GUN H HALL HEAT HOLDUP HOUSE INFRARED INSIDE INTERIOR INTRUSION Ja JEWELRY K KITCHEN 106 107 108 109 110 111 113 114 115 116 117 118 119 121 122 123 125 126 128 129 130 131 132 134 135 136 138 139 140 142 143 144 145 146 147 148 150 151 152 153 LAUNDRY LEFT LEVEL LIBRARY LIGHT LINE LIVING LOADING LOCK LOOP LOW LOWER M MACHINE MAIDS MAIN MASTER MEDICAL MEDICINE MONEY MONITOR MOTHERS MOTION MOTOR N NORTH NURSERY 0 OFFICE OPEN OPENING OUTSIDE OVERHEAD P PAINTING PANIC PASSIVE PATIO PERIMETER PHONE POINT POLICE POOL POWER oe o o Section 13 Alpha Descriptor Programming 155 156 157 159 160 161 162 163 164 165 166 167 168 169 170 171 173 174 175 176 178 179 180 182 184 185 186 190 191 192 193 194 196 197 199 200 201 202 205 206 207 208 R RADIO REAR RECREATION REFRIGERATION RF RIGHT ROOM ROOF S SAFE SCREEN SENSOR SERVICE SHED SHOCK SHOP SHORT SIDE SKYLIGHT SLIDING SMOKE SONS SOUTH SPRINKLER STATION STORE STORAGE STORY SUPERVISED SUPERVISION SWIMMING SWITCH T TAMPER TELCO TELEPHONE TEMPERATURE THERMOSTAT TOOL TRANSMITTER U UP UPPER UPSTAIRS U
52. ED BUT USE MAX OF 220 FT OF 22 WIRE OR 550 FT OF 18 COMPLIES WITH FCC RULES PART 68 FCC REGISTRATION No AC398U 68192 AL E RINGER EQUIVALENCE 0 7B WARNING OWNER S INSTRUCTION NOTICE NOT TO BE REMOVED WEEKLY TESTING IS REQUIRED TO ENSURE PROPER OPERATION OF THIS SYSTEM 02269 PRINTED INFORMATION DESCRIBING PROPER INSTALLATION OPERATION TESTING MAINTENANCE EVACUATION PLANNING AND REPAIR SERVICE IS TO BE PROVIDED WITH THIS EQUIPMENT q xipuaddy LIMITED WARRANTY Pittway Corporation and its divisions subsidiaries and affiliates Seller 165 Eileen Way Syosset New York 11791 warrants its First Alert Professional products to be in conformance with its own plans and specifications and to be free from defects in materials and workmanship under normal use and service for 36 months from the date stamp control on the product or for products not having a date stamp for 30 months from date of original purchase unless the installation instructions or catalog sets forth a shorter period in which case the shorter period shall apply Seller s obligation shall be limited to repairing or replacing at its option free of charge for materials or labor any product which is proved not in compliance with Seller s specifications or proves defective in materials or workmanship under normal use and service Seller shall have no obligation under this Limited Warranty or otherwise if the product is altered
53. ED FOR FIRE INSTALLATIONS USE 12V OPTIONAL ITEMS THAT MAY BE USED OPTIONAL FOR UP TO 30 ADDITIONAL ZONES ONE FROM EITHER OR BOTH GROUPS SET UNIT S DIP SWITCH 17 2AH BATTERY FOR 500mA AUX SEE THEIR INSTRUCTIONS ADEMCO 5881 Type FOR DEVICE ADDRESS OF 0 POWER SEE INSTRUCTIONS ADEMCO No 5800TM RF RECEIVER See receiver s instructions S ONS TRANSMITTER MODULE 20mA WIRELESS ZONES BATTERY CAPACITY FOR EMERGENCY for No 5827BD 5881L UPTO8 BURGLARY STANDBY USE AT LEAST 5881M UP TO 16 AUX PWR 5 4HRS AND OR 5881H UP TO 30 allt BLK GEL LEAD ACID TYPE BATTERY VOLT GE RIGGEN SBE UES N CAMADA EOL BATTERY NORMALLY NEED NOT BE AND OR AND OR POWER REPLACED FOR AT LEAST 3 YRS ADEMCO No 7720PLUS FOR X 10 MODULE ADEMCO No 4204 RELAY MODULE VOLTAGE TRIGGER Lin or 7820 LONG RANGE RADIO PF284 OR EQUIV 4 OUTPUT RELAYS MEMORY OF el sione RELAY CHARGE BATTERY SEE INSTRUCTIONS OR ALARM SEE WIRE SMOKE MODULE VOLTAGE 12V 4AH BLACK ADEMCO No 4219 INSTRUCTIONS DETECTOR A77 716B DI 1000 13 8vDc e g ADEMCO 1 234 WIRED EXPANSION MODULE orms T1 No 467 HED USE CONNECTOR 8 ADDITIONAL EOLR WIRED ZONES EGLA gt OR 12V 1 2AH F O OOO WITH FLYING LEADS ADENCON 1 SUPPLIED jo 4229 as TO DETERMINE TOTAL RED WIRED EXPANSION RELAY MODULE 2 a LOCATED AT A STANDBY LOAD ON JU
54. ETHER DIRECTLY OR INDIRECTLY FOR ANY LOSS OR DAMAGE ARISING UNDER THIS LIMITED WARRANTY OR OTHERWISE REGARDLESS OF CAUSE OR ORIGIN SELLER S MAXIMUM LIABILITY SHALL NOT IN ANY CASE EXCEED THE PURCHASE PRICE OF THE PRODUCT WHICH SHALL BE THE COMPLETE AND EXCLUSIVE REMEDY AGAINST SELLER This warranty replaces any previous warranties and is the only warranty made by Seller on this product No increase or alteration written or verbal of the obligations of this Limited Warranty is authorized lA ert 172 Michael Drive iS PROFESSIONAL Syosset New York 11791 SECURITY SYSTEMS Copyright 1998 PITTWAY CORPORATION K3211 3 98
55. GE RADIO ON CONTROL BOARD Figure 9 2 Connecting a Strobe 93 FA147C Installation Instructions SECTION 10 Long Range Radio In This Section General Information Wiring Connections Programming For Long Range Radio General Information If output to long range radio is selected in field 27 all messages that are programmed to go to the primary telephone line receiver will also be sent to the Ademco 7720PLUS or 7820 long range radio These messages will be in Contact ID format not affected by entry in field 46 The data line is supervised as well as certain functions in the radio If communication is lost or a trouble develops a message will be attempted to be sent via both radio and telephone to the central station For complete information including specific wiring connections refer to the manual that accompanies the long range radio Wiring Connections Connect the data in data out terminals and voltage input terminals of the Long Range Radio to the control s keypad connection points terminals 4 5 6 and 7 as shown below The control should be powered down while making the following wiring connections E BLACK SED 7720 PLUS 7820 LONG RANGE RADIO GREEN CONTROL DATA IN RADIO DATA OUT YELLOW CONTROL DATA OUT RADIO DATA IN CONTROL Figure 10 1 TERMINALS Long Range Radio Connections Using the Memory of Alarm Voltage Trigger for Long Range Radio The Memory of Alarm voltage trigger can be c
56. INSTALLATION INSTRUGTIONS FA147C Security System First i Alert VERSIONA MS K3211 3 98 RECOMMENDATIONS FOR PROPER PROTECTION The following recommendations for the location of fire and burglary detection devices help provide proper coverage for the protected premises Recommendations For Smoke And Heat Detectors With regard to the number and placement of smoke heat detectors we subscribe to the recommendations contained in the National Fire Protection Association s NFPA Standard 72 noted below Early warning fire detection is best achieved by the installation of fire detection equipment in all rooms and areas of the household as follows For minimum protection a smoke detector should be installed outside of each separate sleeping area and on each additional floor of a multi floor family living unit including basements The installation of smoke detectors in kitchens attics finished or unfinished or in garages is not normally recommended For maximum protection the NFPA recommends that you install heat or smoke detectors in the living room dining room bedroom s kitchen hallway s attic furnace room utility and storage rooms basements and attached garages In addition we recommend the following e Install a smoke detector inside every bedroom where a smoker sleeps e Install a smoke detector inside every bedroom where someone sleeps with the door partly or completely closed Smoke could be blocked by the closed
57. LLOW DATA OUT terminal 7 2 Insert the keyed connector at the other end of the connector cable into the mating header on the Phone Module see diagram on next page for location of the header 3 Connect terminals 1 through 5 on the Phone Module as shown in the Wiring Table and in the FA4285 wiring diagram that follows Use an RJ31X jack CA38A in Canada with a direct connect cord and make all connections exactly as shown If the leads on the direct connect cord are too short to reach their assigned terminals splice additional wires to them as required FA4285 WIRING TABLE Connects to G 4 Phone Out Ring RAY lead from direct connect cord Earth ground terminal 21 on control 6 Not Used E ZZZ If no touch tones are produced following access to the security system from on premises this problem may arise in rare cases it may be necessary to reverse the wires connected to terminals 3 and 4 on the Phone Module and the wires connected to terminals 17 amp 18 on the control The wiring diagram shows the wiring connections that will provide proper operation in most cases Caller ID Units xh 82 If the telephone system on the premises includes a stand alone Caller ID unit connect the ID Caller unit directly to the Handset terminals 17 amp 18 on the control as shown in FA4285 Phone Module Wiring Connections diagram that follows If the telephone has a built in Caller ID unit the Ca
58. MPER 8 ADDITIONAL EOLR WIRED ZONES 3 DETECTOR LOWER RIGHT NJ BATTERY ADD 100mA TO r PLUS 2 OUTPUT RELAYS CAUTION OF CIRCUIT TOTAL OF AUX POWER SUT FOR BELL SUPERVISION 1 INCORRECT CONNECTION TO ZONES 1 6 BOARD O SEE INSTRUCTIONS FOR SETUNITS DIPSWITCH IF PROGRAMMED FOR OUTPUT AND REMOTE BELL WIRING i FOR DEVICE ADDRESS OF 1 MAY CAUSE DAMAGE TO HAE uv KEYPAD CURRENTS I See unit s instructions CONTROL UNIT USE UL LISTED LIMITED 3 mawaa 1 2 A 4 Se GO a a ALL CONNECTIONS XK K EARTH o o 2 TO GND TERM 21 T T I I 1 a T sj oe zip iva GROUND ON CONTROL lt T _ z A y BROWN GRAY GREEN RED INSTRUGTIONS O GROUND AUX POWER 5 _ FOR PROPER h TERMINAL oT OUTPUT F A O O O HANDSET INCOMING GROUNDING TRANSFORMER 10 5 13 8VDC qc b b L PHONE O 500mA MAX T eg Li ji 5 LINE lo pr INTERRUPTS o oye TELEPHONE WIRING 5 PLUG IN FOR 4 WIRE Z Slo O O O VIA RJ31X JACK DIRECT SEE INSTRUCTIONS 5 TRANSFORMER FIRE ALARM O 16 F CONNECT CORD FOR SPECIAL D 16 5VAC 25VA RESET Elel 5 Prg Prg g DK IN CANADA CA38A JACK PHONE WIRING IF ADEMCO TO 110VAC note alz z a DOC LOAD NO 3 FA4285 PHONE Q No 1317 KEYPAD g a lt j amp A gt MODULE IS USED cr UNSWITCHED TIER z z 5 3 o OUTLET 24 HR CURRENT amp amp 3 5 S 9 WARNING iu E 5 INGLUDEDIN lt amp z TO PREVENT RISK OF SHOCK DISCONECT AUX CURRENT 2 6 w 4 1000 1000 1000 1000 1000 1000 vw RAN 5 25 gi CRE at
59. Optional Expansion Zones up to 30 total wired and wireless zones Wired Expansion e Supports up to 8 additional wired zones using a 4219 expansion module or 4229 expansion relay module Zones will have the following characteristics e EOLR supervision supporting N O or N C sensors e 300 500 msec normal response with an option for fast 10 15 msec response on loop A first expansion zone Wireless Expansion e Supports up to 30 wireless zones less if using wired expansion zones e Requires the use of a 5881 5882 in Canada type RF Receiver with 5800 series wireless transmitters as shown below Receiver Model No of Zones Transmitter Type 5881L 5882L Up to 8 5800 5881M Up to 16 5800 5881H 5882H Up to 30 5800 Only 5882L or 5882H available for use in Canada Remote Keypads Up to 4 of any of the following keypads may be used Fixed Word Keypads FA210KP FA245KP and FA250KP Fixed word displays Alpha Keypad FA550KP 2 line alphanumeric display 1 1 FA147C Installation Instructions Programming e Programmed options are stored in electrically erasable non volatile EEROM memory information can be reprogrammed at any time and will not be lost in the event of a power loss e Upon exiting the programming mode after programming at the system site all programmed data is automatically uploaded to the central station if the upload was successful a message to that effect will be displayed at the keypads
60. Personal Emergency or 24 hour Fire Emergency responses Not to be used in UL installations The panic function is activated when the appropriate lettered key is pressed for at least 2 seconds or when both keys of the appropriate key pair are pressed at the same time See the chart that follows For the Silent Panic or Medical Personal Emergency functions to be of practical value the system must be connected to a central station 17 3 FA147C Installation Instructions The panic functions are identified by the system as follows Displayed as Zone Notes 1 amp or A Keys A B C are not on all keypads 3 amp 4 or C 6 Key D if present is inactive Mew orB 99 FA4285 Phone Module if used Refer to the separate instructions supplied with the Phone Module for detailed information concerning its operating procedures The check out procedure in the FA4285 Phone Module section should have been performed following installation of the Phone Module Note The Phone Module cannot be used to add user codes in this system User codes must be added by using a wired keypad Relay Outputs if used If relay outputs or an X10 type module is used two keypad entries available to the user are included among the system operation choices 34 and 35 that may be programmed see the Relay Outputs section They can manually activate or de activate the relay s for starting or stopping some action suc
61. Quick Chime Feature The key can be used in place of the security code when turning Chime on and off Optional Bell Supervision Red jumper on control board when cut will provide supervision of bell wiring when bell is wired with EOL resistor as indicated in the instructions Auxiliary Power Output e Provides 12VDC 500mA maximum Uses current limiting circuitry for protection e This output interrupts for smoke detector reset if 4 wire smoke detectors are used on basic wired zones 1 6 if programmed for fire e The system can be uploaded downloaded or controlled via an IBM compatible computer Windows downloading software and a HAYES modem specified by First Alert Keypad programming consists of e Data field programming e Interactive menu mode programming For programming from a keypad an FA550KP 2 line Alpha keypad must be connected but need not necessarily stay in the system e Communication Formats Supported e 4 2 Ademco Low Speed Standard e 4 2 Radionics Standard e 4 2 Ademco Express e Ademco Contact ID Zone Descriptors You can assign Alpha descriptors to all zones useful only when using Alpha keypads and or the FA4285 Phone Module AC Power Supply Uses 1317 120VAC plug in transformer with 16 5VAC 25VA output Back Up Battery Rechargeable Gel type 12VDC 4AH minimum 1 3 FA147C Installation Instructions 14 SECTION 2 Installing The Control In This Section Mounting
62. ST REPORT CODE This is sent periodically to test that the communicator and phone lines are operational frequency of report is selected in field 51 Press 65 OPEN EXIT ALARM REPORT CODE This is sent upon disarming of the system 2nd digit User No if 4 2 reporting is selected Press 66 ARM AWAY STAY REPORT CODES This option allows for independent programming of AWAY and STAY reports 2nd digit of Report is User No if 4 2 reporting is selected Press 67 RF XMTR LOW BATTERY REPORT CODE This is sent in the event that a wireless transmitter low battery condition exists Press 68 CANCEL REPORT CODE This is sent upon disarming of the system after an alarm condition was reported Section 15 System Communication Press 70 ALARM RESTORE REPORT CODE 1st DIGIT This is sent when the zone that caused an alarm is restored to its non faulted condition 2nd digit is automatically sent as the 2nd digit of the zone alarm report code programmed in field 56 if 4 2 reporting is selected Press 71 TROUBLE RESTORE REPORT CODE This is sent when a trouble in a zone is restored Press 72 BYPASS RESTORE REPORT CODE This is sent when a zone that has been bypassed is un bypassed Press 73 AC RESTORE REPORT CODE This is sent when AC power has been restored after an AC power outage Press 74 LOW BAT RESTORE REPORT CODE This is sent when a system low battery condition is restored to normal Press 75 RF XMTR LOW BATTERY RESTORE CODE
63. TAINER Position the lock in the hole making oe Stele certain that the latch will make contact with the latch bracket when the door is closed N UNLOCKED 3 Hold the lock steady and insert the retainer clip into the retainer slots Position the clip as illustrated in order to permit easy removal CABINET DOOR BOTTOM Figure 2 1 Installing the Lock 2 1 FA147C Installation Instructions Before installing the cabinet s contents remove the metal cabinet knock outs required for wiring entry Do not attempt to remove the knockouts after the circuit board has been installed Installing the Control s Circuit Board Alone or if used with a 4204 4219 or 4229 Module Installing the Control s Circuit Board in the Cabinet See Figure 2 2 1 Hang two short mounting clips provided natural color on the raised cabinet tabs see Detail B below 2 Insert the top of the circuit board into the slots at the top of the cabinet Make sure that the board rests on the correct row see Detail A 3 Swing the base of the board into the mounting clips and secure the board to the cabinet with the accompanying screws see Detail B Important Note The two short mounting clips natural color are to be used on the circuit board even when the RF receiver is mounted above it Installing the 4204 4219 or 4229 Module in the Cabinet See Figure 2 2 Any one of these units can be mounted in the cabinet with the main control board if used
64. TILITY 209 210 212 213 214 216 217 219 220 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 V VALVE VAULT VOLTAGE W WALL WAREHOUSE WEST WINDOW WING WIRELESS NS XMITTER Y YARD gt 22 ZONE No ZONE 0 1 1ST 2 2ND 3 3RD 4 4TH 5 5TH 6 6TH 7 7TH 8 8TH 9 9TH Custom Word 1 Custom Word 2 Custom Word 3 Custom Word 4 Custom Word 5 Custom Word 6 Custom Word 7 Custom Word 8 Custom Word 9 Custom Word 10 Bulleted words in boldface type are those that are also available for use by the FA4285 Phone Module If using a Phone module and words other than these are selected for Alpha descriptors the module will not provide annunciation of those words 32 space 33 34 35 36 37 38 40 41 CHARACTER ASCII CHART For Adding Custom Words OTMMUIOTNPaA Vv ovozzraxc c 7I 82 83 84 85 86 87 88 89 90 N lt xs lt CHOD 13 5 FA147C Installation Instructions 13 6 In This Section SECTION 14 Sequential Mode For 5800 Wireless Transmitters General Information Sequential Enrolling General Information xh Use this mode only after all other zone information has been programmed including transmitter loop numbers There are two methods of enrolling you can enroll each transmitter in
65. Voltage Input 12VDC Current Drain 35mA Relays off 100mA Relays on 3 Interface Wiring Same as FA210KP 4 8 EOLR Loops Loop A can be set for fast 10 15msec response to an open A H 5 Two Output Relays SPDT Contacts Rating 2A max at 28VDC AC FA4285 Phone Module 1 Physical 6 1 2 W x 4 1 4 H x 1 1 4 D 169mm x 108mm x 32mm 2 Electrical Voltage Input 12VDC Current Drain 160mA 3 Device Address Permanently set to address 4 4 Interface Wiring See FA4285 Phone Module section 5 Telephone Line Connections See FA4285 Phone Module section 7720PLUS 7820 Long Range Radio 1 Physical 8 1 2 W x 9 1 2 H x 1 3 4 D 216mm x 242mm x 45mm 2 Electrical Voltage Input 12VDC Current Drain 150mA 3 Device Address Set to address 3 4 Interface Wiring Same as 4127 above Accessories Compatible Devices Sounders Ademco AB 12M 10 Motor bell amp box UL Grade A 100mA current draw Motorized Bell amp Box Ademco 1011BE12M 10 Motor bell amp box UL Listed 100mA current draw Motorized Bell amp Box Ademco 702 Outdoor Self contained 6 12 volt siren driver built in and Siren weatherproof for outdoor use Can be wired for either a steady or warble sound 117dB 10 feet 1500mA current draw Ademco 719 Self contained 6 12 volt siren driver built in Steady or 2 Channel Siren warble sound 109dB 10 feet 550mA current draw Ademco 747 Self contained 6 15 volt siren
66. a supervisory module to supervise power e g System Sensor No A77 716B Relay module to meet NFPA 72 requirements AUX PWR O OUTPUT TERMINALS O ha EOL POWER SUPERVISION RELAY 4 WIRE SMOKE DETECTORS MODULE A77 716B TO HI SIDE EOLR OF ZONE TO LO SIDE DETECTOR OF ZONE Figure 4 1 4 wire Smoke Detector Connections Compatible System Sensor 4 Wire Smoke Combustion Detectors 1412 4 wire ionization products of combustion detector 2412 4 wire photoelectric smoke detector 2412TH 4 wire photoelectric smoke detector w 135 F 57 C heat detector A77 716B EOL relay module supervisory module for wired 4 wire fire zone 2112 24T Low profile 4 wire photoelectric smoke detector w 135 F 57 C heat detector Programming Hard Wired Zones 1 Atleast one 2 line Alpha keypad FA550KP must be connected to the keypad terminals on the control and the system powered up 2 Enter the programming mode by keying the following on the Alpha keypad INSTALLER code 3 519 8 0 Data fields 22 RF SYSTEM and 25 WIRED EXPANSION RELAY USED must be programmed as required before continuing 3 Press 56 Note that this is an interactive programming mode You will use it to program zone numbers zone types and alarm report codes for hard wired zones If you enabled the 5800 wireless system in field 22 a 1 entry the first screen prompt will be Pr
67. al range of 200 feet Take this into consideration when determining mounting location outside of the cabinet 2 Make sure that the receiver s DIP switches are set for device address 0 as shown in Figure 6 1 all switches to the right OFF 3 With the control powered down connect the receiver s wire harness to the control s keypad terminals 4 5 6 and 7 Plug the connector at the other end of the harness into the receiver see Figure 6 1 4 Refer to the receiver s installation instructions for further installation instructions regarding antenna mounting etc Section 6 Wireless RF Zone Expansion 5800 RF Systems NOTE WHEN CIRCUIT BOARD IS MOUNTED IN CONTROL S CABINET GROUNDING LUGS 2 PROVIDED MUST BE INSERTED IN LEFT HANDTER MINALS OF ANTENNA BLOCKS AND L ANTENNAS L SECURED TO CABINET SEE RECEIV INSERT IN ER S AND CONTROLS INSTRUCTIONS RIGHT HAND TERMINALS KEYPAD CONNECTION BLACK TO CONTROL S REMOTE POINTS EACH RECEIVER Lt LOCATION CIRCUIT BOARD WIRING MUST BE ON INDIVIDUAL amp OPENING HOME RUN PA INTERFERENCE DIP SWITCH NEEG INDICATOR KNOCKOUT AREA FOR 4 SURFACE HOS WIRING I gt Eli TO RELEASE CIRCUIT BOARD REMOVE SCREWS 2 AND BEND BACK TABS S Figure 6 1 5881 amp 5882 Series Wireless Receivers cover removed Installing the 5800TM Module Installation of this module is necessary only if you are using one or more 5827BD Wireless Bi directional keypads
68. ard again Press the key to continue This screen displays a summary of the current relay START programming in this example relay 04 is shown selected Press the key to continue 04 A EV ZL ZT STT 0 0 0 00 04 A EV ZL ZT This screen displays a summary of the current relay STOP programming STP 0 00 Press the key to continue Enter the desired X10 action When programming for an X10 type module any of the selections below may be selected except 0 since the X10 will default to close and stay closed regardless of the selection made here 0 No response 1 Close for 2 seconds 2 Close and Stay Closed 8 Continuous Pulse on amp off 1 sec ON 1 sec OFF Press the key to continue Enter the event that will START the X10 action as an example alarm is shown selected 0 Not used 2 Fault 1 Alarm 3 Trouble Note A zone list must be used in conjunction with an event Press the key to continue If a zone list will be used to START the X10 action enter the zone list number to be programmed in field 81 1 2 or 3 If Chime by Zone has been selected in field 31 Zone List 3 should be reserved for entry of zones to be programmed for Chime by Zone See Programming for Chime by Zone later in this section Press the key to continue If a zone type or system operation will be used to START the action enter the 04 Start appropriate tw
69. as 3 unique input loop codes Loop 1 Built in shock sensor loop wired to TB1 normally closed Loop 2 For a closed circuit contact loop using the built in reed switch in conjunction with a magnet Loop 3 Externally wired closed circuit contact loop connected to TB2 e Can be used to turn the burglary protection on and off e Features the same built in panic functions as wired keypads e The keypad is identified as zone 00 on wired keypads when it transmits with a low battery e Requires 5800TM Transmitter Module e Operates the system similarly to wired keypads including panic functions e Can indicate system status via its 3 LEDs and sounder e Includes 3 panic keys e House ID must be set e Requires both sound and shock of breaking glass to cause alarm to be transmitted e Dual element passive infrared detector transmitter with built in selectable pulse count Note There is a 3 minute lock out between fault transmissions to conserve battery life Package of 4 magnets for use with 5816 and 5817 transmitters Section 6 Wireless RF Zone Expansion 5800 RF Systems Programming the Receiver and Transmitters 5800 RF System xh 1 At least one 2 line Alpha keypad FA550KP should connected to the keypad terminals and the system powered up 2 Enter the programming mode by keying Installer Code 8 0 Data field 22 RF SYSTEM TYPE must be programmed before continuing 1 must be entere
70. ated e Move the radio or television receiver away from the receiver control e Move the antenna leads away from any wire runs to the receiver control e Plug the receiver control into a different outlet so that it and the radio or television receiver are on different branch circuits If necessary the user should consult the dealer or an experienced radio television technician for additional suggestions The user or installer may find the following booklet prepared by the Federal Communications Commission helpful Interference Handbook This booklet is available from the U S Government Printing Office Washington DC 20402 The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User s Manual Unauthorized changes or modifications could void the user s authority to operate the equipment Federal Communications Commission FCC Part 68 Statement This equipment complies with Part 68 of the FCC rules On the front cover of this equipment is a label that contains among other information the FCC registration number and ringer equivalence number REN for this equipment If requested this information must be provided to the telephone company This equipment uses the following jacks An RJ31X is used to connect this equipment to the telephone network The REN is used to determine the quantity of devices which may be connected to the telephone line Excessive RENs on the telep
71. ccur e A display of KYPD LB on Alpha keypads without a zone number indicates that a 5827 5827BD wireless keypad or 5804BD has a low battery If the battery is not replaced within 30 days a CHECK display may occur Note Some wireless sensors contain a non replaceable long life battery which requires replacement of the entire unit at the end of battery life e g Nos 5802 5802CP Power Failure e If there is no keypad display at all and the POWER indicator if present is not lit operating power for the system has stopped and the system is inoperative Note The control panel will power up in its previous state armed or disarmed after a complete power failure but will not retain any memory of bypasses e If the message AC LOSS Alpha keypads or NO AC Fixed word keypads is displayed the keypad is operating on battery power only Note There is a random delay up to 48 minutes before the system will report an AC failure to the central station The keypad response is about 6 seconds The restore report has a random delay of up to 12 minutes if the AC failure report was sent e If the battery standby capacity is used up during a prolonged AC power outage the control s auxiliary power will shut down to minimize deep discharge of the battery Other Displays Fixed Word displays are in parentheses Busy Standby dI If this remains displayed for more than 1 minute the system is disabled Modem
72. chosen e g End of Exit Time that operation will cause the relay to activate as selected in ACTION The different choices for ZONE TYPE and SYSTEM OPERATION are listed in Programming Output Relays later in this section and in the Programming Form in the separate Programming Guide The STOP programming determines when and under what conditions the relay will be de activated The following options are available RESTORE ZONE LIST ZL If a ZONE LIST is used as the Stop event the relay will de activate when all the zones in that list restore from a previous fault trouble or alarm condition This will occur regardless of what is programmed to START the relay therefore a RESTORE ZONE LIST would normally only be used when a ZONE LIST is used to start the relay ZONE TYPE SYSTEM OPERATION ZT Instead of using a RESTORE ZONE LIST a specific zone response type or system operation action can be selected to de activate the relay If a specific ZONE TYPE is chosen any zone of that response type that restores from a previous alarm trouble or fault condition will cause the relay to de activate If a SYSTEM OPERATION is chosen that operation will cause the relay to de activate If relay outputs are used two keypad entries available to the user are included among the System Operation choices that may be programmed 34 and 35 They can manually activate or de activate the relay s for starting or
73. ck up battery which has sufficient capacity to operate the panel and its attached peripheral devices for 24 hours in the intended standby condition followed by at least 4 minutes in the intended fire alarm signaling condition This control panel can meet these requirements without using a supplementary power supply provided that the panel s auxiliary power and bell output currents are limited as indicated in the following table Section 20 Regulatory Agency Statements OUTPUT LIMITATIONS TO MEET CSFM 24 HOUR BATTERY BACK UP REQUIREMENTS FOR UL LISTED RESIDENTIAL FIRE INSTALLATIONS OUTPUT CURRENT LIMITATIONS BATTERY INFORMATION OUTPUT CURRENT MAXIMUM BATTERY CAPACITY RECOMMENDED BATTERY TOTAL AUXILIARY CURRENT TO USE Amp Hrs Yuasa Model No 600mA maximum total 45mA 4AH NP4 12 of 160mA 7AH NP7 12 auxiliary power 200mA SAH NP4 12 two plus bell output currents 425mA 14AH NP7 12 two Note Use two batteries connected in parallel Obtain an Ademco No 4100EOLR Resistor Kit A dual battery harness is provided with the kit The kit also contains EOL resistors with spade lug heat shrink tubing construction which has been approved by UL and CSFM for fire zone usage Both batteries will fit inside the panel s cabinet Canadian Department Of Communications DOC Statement NOTICE The Canadian Department of Communications label identifies certified equipment This certification means that the equipment meets c
74. d for 5800 RF system 3 24 RF HOUSE ID CODE Default is 00 The House ID identifies a 5827 5827BD Wireless keypad or 5804BD Wireless key if they are to be used enter 01 31 The keypad should be set to the same ID If 5827 5827BD or 5804BD are not being used leave as 00 Enrolling Transmitters Into The System xh There are two methods that may be used to enroll transmitters The first method is performed in 56 zone programming mode which is contained in this section and describes how to enroll each transmitter into the system as you are entering the zone information The second method is called sequential enrolling which uses 83 mode contained in the Sequential Mode section later in this manual This section describes how to enroll all the transmitters into the system after all zone information has been entered As an option the zone programming and sequential modes allow you to use a 5804 button type transmitter as a program tool The upper left hand and right hand buttons of the tool duplicate the and keypad programming functions left right The advantage of using a program tool is that it enables remote enrolling You can move to the physical location of the transmitter to be enrolled press the upper left hand button of the program tool and then trip the intended transmitter see step 10 for operation The transmitter that you use as the program tool can also be used as a transmitter in
75. d in field 95 to bypass an answering machine and an FA4285 Phone Module is the control panel will answer thinking that the PC downloader is on line After fax like tones are given the control panel will hand off to the phone module and 2 long tones will be heard followed by the usual voice prompt for the 2 digit phone access code If this procedure is not followed Phone Module operation will not be possible 5 Zone descriptors should also be programmed regardless of the type of keypads in use If this is not done the Phone Module will not annunciate a description of the zone s in alarm trouble etc the Phone Module will annunciate zone numbers only You can enter zone descriptors now using interactive mode 82 or later See the Alpha Descriptor Programming section for a detailed procedure 6 Exit the programming mode by entering 99 Perform a preliminary check of the FA4285 Phone Module as indicated next Section 8 FA4285 Phone Module Checking the Operation of the FA4285 Phone Module To Check Phone Module Operation From an On Premises Phone 1 Pick up phone and enter the programmed 2 digit phone code entered in field 26 VOICE MODULE ACCESS CODE Annunciation of a system status report should automatically start See the User s Guide accompanying the Phone Module for detailed information regarding the nature of the status report if necessary During any pause in the status report or immediately following it key
76. d to remove secondary user codes from the system individually If a Duress Code user 8 is not assigned up to 6 secondary user codes users 3 8 will be available for assignment To assign or change a Secondary security code enter Master Code 8 User 3 77 desired 4 digit User Code t User 8 is reserved for a Duress Code However if a Duress code is not assigned a security code can be assigned to an additional user who will be user 8 The system will emit a single beep when each secondary user code has been successfully entered 17 1 FA147C Installation Instructions To delete a Secondary security code enter Master Code 8 User Special Notes e All Master and secondary user codes permit access to the system for arming disarming etc e Ifa secondary user code is inadvertently repeated for different users the lower user number will take priority e Opening and closing reports are sent for the Master code as No 02 with the appropriate subscriber number Secondary user codes are sent as Nos 3 through 7 or 8 if no Duress code is assigned respectively with the appropriate subscriber number Duress Code Important This code is useful only when the system is connected to a central station This feature is intended for use when you are forced to disarm or arm the system under threat When used the system will act normally but can silently notify the central station of your situation if
77. driver built in for indoor wall Indoor Siren mount 747F available for flush mounting 105dB 10 feet 400mA current draw 19 3 FA147C Installation Instructions 19 4 Sounders Continued Ademco 747UL Indoor Siren Self contained 6 15 volt siren driver built in for indoor wall mount UL Listed 85dB 10 feet 320mA current draw Ademco 744 Siren Driver 6 jumper selected sound outputs Rated at 119dB with use of an 8 ohm 30 watt speaker 1 3 amps current draw Ademco 745X3 Voice Siren Driver 12 volt voice siren driver with English Spanish and French voice messages Separate messages for Fire and Burglary Use with 8 ohm speaker UL Listed 1100mA current draw Ademco 705 820 5 inch Round Speaker 20 watt 8 ohm indoor or outdoor speaker Requires a driver Ademco 713 Speaker 40 watt 8 ohm indoor outdoor speaker Requires a driver System Sensor PA400B beige PA400R red Indoor Piezo Sounder Indoor piezo sounder red or beige rated at 90 dB 10 feet Requires special power wiring connections Compatible 4 Wire Smoke Combustion Detectors System Sensor 1412 4 wire ionization products of combustion detector 2412 4 wire photoelectric smoke detector 2412TH 4 wire photoelectric smoke detector w 135 F 57 C heat detector A77 716B EOL relay module supervisory module for wired 4 wire fire zone 2112 24T Low profile 4 wire photoelectric smoke detector w 1
78. e Alarm Output loop connected to an external sounder is opened or shorted the message Bell Failure Custom English display touchpads or CHECK 70 Fixed English display touchpads will be displayed accompanied by a trouble sound A report will also be sent to the central station To enable this option 1 Cut the red jumper on the control board see Figure 9 1 2 Connect a 1000 ohm resistor across the sounder terminals not at the Alarm Output terminals TERMINALS ON EXTERNAL ALARM CONTROL BOARD SOUNDER 1000 OHM EOL RESISTOR OBSERVE ALARM POLARITY OUTPUT TERMINALS IF BELL SUPERVISION IS ENABLED RED JUMPER ON CONTROL BOARD IS CUT CONNECT A 1000 OHM RESISTOR ACROSS THE EXTERNAL amp CUT RED JUMPER ON CONTROL SOUNDER AS SHOWN BY THE DOTTED LINE BOARD TO ENABLE BELL SOUNDER DO NOT CONNECT THE RESISTOR AT THE SUPERVISION ALARM OUTPUT TERMINALS THEMSELVES Figure 9 1 Sounder Wiring Programming for External Sounders 1 At least one 2 line Alpha keypad FA550KP must be connected to the keypad terminals on the control and the system powered up 2 Enter the programming mode by keying the following on the Alpha keypad INSTALLER code 8 0 9 2 Section 9 External Sounders 3 Press 28 Single Alarm Sounding per Zone Armed Period Enter 1 for yes 0 for no default 4 Press 29 Fire Sounder Timeout Enter 1 for no timeout 0 for timeout defa
79. e a cloth to mask them temporarily if necessary 2 Power up the system by plugging in the AC transformer 3 With all hard wired zones intact the Alpha keypad connected to the system DISARMED READY TO ARM should display If the following is displayed DISARMED Press to show faults press the key to display the faulted zone s Restore any faulted zone s as necessary also make sure that you have connected a 1000 ohm EOL resistor across the terminals of any unused hard wired zones When the DISARMED READY TO ARM message is displayed you can proceed to the next step 4 Fault and then restore every contact or sensor on each zone individually to ensure that it is being monitored by the system Each time a zone is faulted the keypad should display the number of the faulted zone When each zone is restored the READY TO ARM message should appear again 5 When you get the proper displays on the keypad s the hard wired zones in the system are functioning properly 6 Unplug the AC transformer if other connections are going to be made to the control 4 5 FA147C Installation Instructions SECTION 5 Wired Zone Expansion In This Section General Information Installing Zone Expansion Units Programming Wired Expansion Zones Check Out Procedure For Wired Expansion Zones General Information This section provides information regarding the use of expansion modules 4219 or 4229 for expa
80. e battery size needed you must add the 100mA drawn by the control itself to the total Auxiliary current draw in the worksheet oh Do not connect to the battery until all devices have been wired to the control 2 Attach the Red and Black wires on the battery connector cable as follows a Red to the positive battery tab on the control board b Black to the negative battery tab on the control board This not required if wires were previously connected to the battery tabs on the control 3 Attach the Red and Black wires at the other end of the battery connector cable to the battery as follows a Red to the positive terminal on the battery b Black to the negative terminal on the battery AUXILIARY DEVICE CURRENT DRAW WORKSHEET CURRENT NUMBER OF TOTAL CURRENT DEVICE USED DRAW DEVICES device mA x of units FA4285 Phone Module 160mA Long Range Radio Depends on Radio used see its instructions Too o ae ile vl ko og TOTAL Current available from Aux terminals 500mA max i Figures are for relays OFF relays ON If using hard wire devices such as PIRs refer to the specifications for that particular unit s current draw and include on worksheet Tn UL installations maximum current draw from the Auxiliary Output and the Alarm Output combined must not exceed 600mA 12 2 SECTION 13 Alpha Descriptor Programming In This Section General Information Assig
81. e installed system 1 2 3 4 Enter the Installer Code 4 Once transmitters are placed in their desired locations and the approximate length of wire to be run to sensors is connected to the transmitter s screw terminals fault each transmitter Do not conduct this test with your hand wrapped around the transmitter as this will cause inaccurate results e The keypad will beep three times to indicate signal reception e Ifthe keypad does not beep re orient or move the transmitter to another location Usually a few inches in either direction is all that is required Mount the transmitter according to the instructions provided with the transmitter Exit the GO NO GO test mode by entering Installer Code OFF To Either Temporarily Or Permanently Remove A Zone in 56 Mode 1 2 3 4 Enter the programming mode Installer Code 8 0 and press 5 6 Enter the zone number and press A summary display will appear Press again The Zone Type prompt will appear Enter 0 0 This sets the zone type to Not Used 20 Zone Type Not Used 00 Press to continue 6 11 FA147C Installation Instructions 20 Delete Zone 1 Yes 0 No The next prompt will ask whether you want to delete the zone Yes will permanently remove the zone from the system while a No will disable it but re tain all data except the original zone type You can then go back to this zone later and pu
82. e to successfully perform the required programming Before any programming is attempted we therefore urge you to read the Mechanics of Programming and the Data Field Descriptions in the separate Programming Guide that has been supplied If you are an experienced user of First Alert Professional products you may choose to wire and then program the entire system at one time If so refer to Mechanics of Programming and Data Field Descriptions in the separate Programming Guide after the hardware setup is complete The Programming Guide contains all of the information you will need to program the system including a blank Programming Form except for detailed programming for hardwired zones 1 6 wired expansion zones and wireless zones These are contained in the following sections in this manual Section 4 Basic Hardwired Zones 1 6 Section 5 Wired Expansion Zones and Section 6 Wireless RF Zone Expansion 5800 RF Systems This manual uses various icons to denote critical notes and technical tips to assist you with the installation of this system see next page vii vili CONVENTIONS USED IN THIS MANUAL UL These notes include specific information which must be followed if you are installing this system for a UL Listed application These notes include information that you should be aware of before continuing with the installation and which if not observed could result in operational difficulties
83. echnical Support via modem to ATLIS BBS Technical Support s Electronic Bulletin Board System Replies are posted within 24 hours East Coast Technical Support 1 800 538 5585 8 a m 6 p m E S T West Coast Technical Support 1 800 458 9469 8 a m 5 p m P S T Technical Support FAX Number 1 800 447 5086 ATLIS BBS Electronic Bulletin Board System 1 516 496 3980 1200 9600 Baud 8 Data Bits 1 Start Stop Bit No Parity ATLIS FAX Automated Fax Retrieval System 1 800 573 0153 1 516 921 6704 Ext 1667 First Alert World Wide Web Page HTTP www firstalert com INTERNET E Mail Address First Alert Tech SPRT First Alert 165 First Alert com 18 3 FA147C Installation Instructions 184 SECTION 19 Specifications and Accessories In This Section Specifications Accessories Compatible Devices s Specifications FA147C Security Control 1 Physical 12 1 2 W x 14 1 2 H x 3 D 318mm x 368mm x 76mm 2 Electrical VOLTAGE INPUT 16 5VAC from plug in 25VA transformer Ademco No 1317 RECHARGEABLE BACK UP BATTERY 12VDC 4AH Gel type Charging Voltage 13 8VDC ALARM SOUNDER 12V 2 0 Amp output can drive 12V BELLS or can drive one or two 702 series connected self contained 20 watt sirens Do not connect two 702s in parallel AUXILIARY POWER OUTPUT 12VDC 500mA max Interrupts for 4 wire smoke detector reset Note For UL installations Alarm Sounder plus Auxiliary Power currents should n
84. ecommended firmly secured to the pipe to which the ground lead is electrically connected and secured AC Power Outlet Ground Available from 3 prong 120VAC power outlets only To test the integrity of the ground terminal use a three wire circuit tester with neon lamp indicators such as the UL Listed Ideal Model 61 035 or equivalent available at most electrical supply stores 2 5 FA147C Installation Instructions 2 6 In This Section SECTION 3 Installing Remote Keypads General Information Keypads That May Be Used Wiring to the Keypads Mounting the Keypads Using a Supplementary Power Supply to Power Additional Keypads Preliminary Check out Procedure General Information This section lists the wired keypads that may be used and provides instructions for wiring and mounting the keypads A preliminary check out procedure is also provided to ensure that the connected keypads are functioning properly in the system Keypads That May Be Used Fixed Word Display FA210KP FA250KP FA245KP e Alpha Display FA550KP Up to 4 keypads independent of auxiliary power considerations you may need to use an auxiliary power supply if the 500mA aux output is exceeded Be sure the keypads are set to the non addressable mode address 31 Wiring To The Keypads xh 1 Determine wire gauge by referring to the wiring length gauge chart below For devices Keypads RF Receivers Expansion Relay
85. ed The 4 digit number CCCC that follows this code will be the User number Examples of typical pager displays follow The optional 16 digits preceding the 7 digit status code that may be programmed for additional data in field 93 have not been included in the examples below Example 1 Pager displays 911 0004 This indicates that the system is reporting an alarm 911 caused by a fault in zone 4 0004 Example 2 Pager displays 102 0005 This indicates that the system is reporting a closing system arming 102 by User 5 0005 Note that no restore reports are sent to the pager Important AAV should not be used when Paging or Alarm Reports are being sent to a Secondary number If this is done the call to the Secondary number by the communicator after the alarm report will prevent the AAV from taking control of the telephone line and the AAV Listen in session cannot take place Press 48 15 SECOND DIALER DELAY BURGLARY Enter 0 for no or 1 for yes Default is 0 no delay Press 49 PERIODIC TEST REPORT Select the desired test report interval 0 none 1 24 hours 2 weekly 3 30 days Default is 0 none Test Report Code entered in field 64 is sent Reports with Subscriber No 15 5 FA147C Installation Instructions 15 6 Press 50 SESCOA RADIONICS SELECT 0 Radionics 0 9 B F reporting 1 SESCOA 0 9 only reporting Select 0 for all other formats Default is 0 To Program Sy
86. ents in this product and all necessary repairs must be made by the manufacturer Other repair methods may invalidate the FCC registration on this product This equipment cannot be used on telephone company provided coin service Connection to Party Line Service is subject to state tariffs This equipment is hearing aid compatible When programming or making test calls to an emergency number briefly explain to the dispatcher the reason for the call Perform such activities in the off peak hours such as early morning or late evening UL Notices 1 This is a Grade A residential system 2 The FA4285 Phone Module and Ademco 7720PLUS or 7820 Long Range Radios have not been UL tested and cannot therefore be used in a UL installation 3 Entry Delays fields 37 38 cannot be greater than 45 seconds for UL installations 4 The maximum number of reports per armed period field 92 must be unlimited set to 1 for UL installations 5 Periodic testing field 49 must be at least every 24 hours set to 1 for UL installations 6 Alarm Sounder plus Auxiliary Power currents must not exceed 600mA total for UL installations 7 Downloading is not permissible for UL installations California State Fire Marshal CSFM 24 Hour Battery Back Up Requirements The California State Fire Marshal has published new regulations which require that all residential fire alarm control panels installed after June 30 1993 must be provided with a ba
87. er will disappear from the display The transmitter codes may be checked upon installation or in an installed system All the wireless zone numbers should disappear after about 1 1 2 hours To speed this process all sensors can be physically faulted and then restored Notes e All BR type units must physically be activated to clear the display e When one button of a transmitter RF UR or BR is activated all zones assigned to other buttons on that transmitter are cleared This also applies to 5816 and 5817 transmitters which have multiple loops zones e Any transmitter serial number that is not entered will not turn off its zone number Exit this mode by keying INSTALLER code OFF b GO NO GO TEST MODE By pressing INSTALLER code 4 4 a mode similar to the user test mode code TEST is entered but the wireless receiver gain is reduced Checking in this mode verifies that the RF transmission has sufficient signal amplitude margin for the installed system Exit the mode by entering INSTALLER code OFF TO THE INSTALLER Regular maintenance and inspection at least annually by the installer and frequent testing by the user are vital to continuous satisfactory operation of any alarm system The installer should assume the responsibility of developing and offering a regular maintenance program to the user as well as acquainting the user with the proper operation and limitations of the alarm system and its compo
88. eractive programming mode It is used to program zone numbers zone types and alarm report codes for all zones that are going to be used If you enabled the 5800 wireless system in field 22 a 1 entry the first screen prompt will be Program Tool O0 No 1 Yes Enter 0 No The next prompt will ask you to enter zone number Enter Zn Num 00 Quit Zone Number Zn ZT RC In L 10 00 00 FF 1 Zone Number 10 Zone Type Perimeter Zone Type 03 entry shown 52 Enter the first zone number that you wish to program or 0 0 to exit zone programming Normally you will be starting with zone 10 this is the default Press to continue A summary display will appear showing the present status of that zone s programming Zn zone number ZT zone type RC report code for that zone In input type of zone AW for Aux Wired L Loop not used for wired expansion zones Values in the summary display are the currently programmed values To start programming zone 10 press A prompt for Zone Type will appear Each zone must be assigned a zone type which defines the way in which the system responds to faults in that zone A detailed explanation of each zone type is provided in Response Type Definitions in the separate Programming Guide Enter the desired zone type from the list below 00 Zone Not Used 07 24 Hr Audible 01 Entry Exit 1 08
89. erface Wiring Same as FA210KP 5881L 5881M 5881H Rf Receivers 5800 System 1 Physical 7 3 8 188mm W x 4 3 8 112mm H x 1 7 16 837mm D Note 10 7 8 277mm H with antenna 2 Electrical Voltage Input 12VDC Current Drain 35mA 3 Interface Wiring Same as FA210KP 4 Range 200ft 60m nominal indoors from wireless transmitters the actual range to be determined with system in TEST mode 5 Zones 5881L accepts up to 8 transmitters 5881M accepts up to 16 transmitters 5881H accepts up to 30 transmitters 5800TM Transmitter Module used with 5827BD Wireless 2 Way Keypad 1 Physical 2 1 4 W x 4 1 8 H x 7 8 D 57mm x 105mm x 22mm 2 Electrical Voltage Input 12VDC Current Drain 20mA 3 Interface Wiring Same as FA210KP 4204 Relay Module 1 Physical 6 1 2 W x 4 1 4 H x 1 1 4 D 169mm x 108mm x 32mm 2 Electrical Voltage Input 12VDC Current Drain 15mA Relays off 180mA Relays on 3 Interface Wiring Same as FA210KP 4 Four Output Relays SPDT Contacts Rating 2A max at 28VDC AC Section 19 Specifications and Accessories 4219 Wired Expansion Module 1 Physical 6 1 2 W x 4 1 4 H x 1 1 4 D 169mm x 108mm x 32mm 2 Electrical Voltage Input 12VDC Current Drain 35mA 3 Interface Wiring Same as FA210KP 4 Four Output Relays SPDT Contacts Rating 2A max at 28VDC AC 4229 Wired Expansion Relay Module 1 Physical 6 1 2 W x 4 1 4 H x 1 1 4 D 169mm x 108mm x 32mm 2 Electrical
90. ertain telecommunications network protective operational and safety requirements The Department does not guarantee the equipment will operate to the user s satisfaction Before installing this equipment users should ensure that it is permissible to be connected to the facilities of the local telecommunications company The equipment must also be installed using an acceptable method of connection In some cases the company s inside wiring associated with a single line individual service may be extended by means of certified connector assembly telephone extension cord The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by the supplier Any repairs or alterations made by the user to this equipment or equipment malfunctions may give the telecommunications company cause to request the user to disconnect the equipment Users should ensure for their own protection that the electrical ground connections of the power utility telephone lines and internal metallic water pipe system if present are connected together This precaution may be particularly important in rural areas Caution User should not attempt to make such connections themselves but should contact the appropriate electric inspection authority or electrician as appropriate The Load Number LN assig
91. essing any key will silence the keypad sounder for 10 seconds Disarming the system will silence both keypad and external sounders When the system is disarmed any zones that were in an alarm condition during the armed period will be displayed memory of alarm To clear this display simply repeat the disarm sequence enter the security code and press the OFF key again The keypads also feature chime annunciation and 3 panic key pairs or individual panic keys depending on keypad type see Panic Keys that follows for silent audible fire or medical personal emergency alarms These keys can notify the central station of an alarm condition if that service is connected Section 17 System Operation Arming Disarming Functions etc The following is a brief list of system commands For detailed information concerning system functions refer to the User s Manual Disarmed Not Ready Before arming the system must be in the READY condition all zones must be intact If the NOT READY message appears press the READY key to display faulted zones Arming Away Enter code AWAY 2 Arming Stay Enter code STAY 3 Arming Instant Enter code INSTANT 7 Arming Maximum Enter code MAXIMUM 4 Quick Arming If enabled Simply press key in place of code then press AWAY STAY INSTANT or MAXIMUM to arm system as
92. f desired NOTES e Any list may include any or all of the system s zone numbers e Azone list can be assigned to more than one output relay e If you only want to review what has been programmed previously enter 8 1 The review can be advanced by using the key When finished enter 0 0 to quit No programmed values can be changed in this mode When relay programming in 80 and 81 interactive menu modes is completed exit the programming mode by keying 99 Programming For an X10 Type Module such as PF284 or equivalent Programming Procedure You must program relay number 4 in field 80 even if a relay module is not being used 1 Enter the programming mode by keying the following on the Alpha keypad INSTALLER code 8 0 2 Press 80 This is an interactive menu programming mode that is normally used to program output relays used in the system In this case it will be used to program for an X10 type module Refer to the Programming Form worksheet in the separate Programming Guide for 80 Interactive Mode Continued over 7 7 FA147C Installation Instructions Output Relay Displays Upon pressing 80 this screen will appear Enter the Relay Number Assuming the use of a 4204 even if not used enter 04 The key is used to accept an entry and advance to the next prompt The key is used to revert back to the last question to check or change an entry Press to go forw
93. f either not using a tool or one has already been programmed skip to step 4 Program Tool 3 If 1 is entered the system will prompt for the 00 Input S N transmitter s serial number Enter the program tool s serial AX X X X X X X number using one of the following methods a Enter the 7 digit serial number printed on the transmitter or 00 Input S N b Press any button on the transmitter The keypad should A123 4567 beep twice and display the serial number of the tool In this example the serial number is A123 4567 Once enrolled the upper left hand button of the program tool can be pressed to ready the system for enrolling a transmitter into the system The serial number for the program tool will only remain in the system until the programming mode is exited Entering 97 will not delete the tool FA147C Installation Instructions Enter Zn Num 00 Quit 10 Zone Number Entered 10 Input S N A 022 4064 Serial Loop Pressing the key on the keypad will cause the system to back up to the Program Tool prompt Press to continue 4 Enter the first zone number to be enrolled e g zone 10 Press to continue The system will starting with this zone number search for the first transmitter which has all of the following attributes pre programmed in Zone Programming a An input type of RF UR or BR programmed b A loop number programmed c No serial number programmed
94. g exit of Fixed Word programming mode CONTROL 1 AC LOSS or NO AC Interrupted AC power supply displayed Control in TEST mode Telephone connection not secure 2 Digital communicator message not being received 2p Digital communicator malfunctioning Telephone number in program needs prefix or access code Telephone call to central monitoring station requires operator assistance 18 2 ta Check transformer connection and power line circuit breaker Transformer must be connected to an unswitched 24 hour outlet 2a Remove from TEST mode 2b Check all connections 2c Check with a different FA147C 2d Program prefix or access code into the control 2e System cannot work in this situation Section 18 Troubleshooting Guide CONTROL Continued SYMPTOM POSSIBLE CAUSE REMEDY 3 Does not arm properly 3a Ready light not on 3a Check for faulted zone s by pressing make faulted zone s intact or use Bypass arming if desired 4 FA147C doesn t respondto 4a CC or MODEM COMM displayed 4a System is in communication with keystrokes on keypad downloader at central station Wait until download session is finished 4b d1 or Busy Standby is displayed 4b System has just been powered and is in its one minute initialization To bypass this time press 0 4c E4 or E8 displayed 4c More zones have been programmed than the zone expansion modules can handle
95. h as turning lights on or off etc These keypad entries are Security Code 7 and Security Code 8 Note Whichever entry is used to start stop the action cannot also be used to stop start it The opposite action must either be performed by the other keypad entry or by some other event or operation offered in the programming section Exit Alarm Displays if programmed e A display of CANCELED ALARM or CA and a zone indication will appear if an exit or interior zone contained a fault during closing at the time the exit delay ended e g exit door left open but the system was disarmed during the entry delay time The alarm sounder and keypad sound continuously but stop when the system is disarmed No message will be transmitted to the central station e A display of EXIT ALARM or EA and a zone indication will appear if an exit or interior zone contained a fault during closing at the time the exit delay ended but the system was NOT disarmed during the entry delay time The alarm sounder and keypad sound continuously until the system is disarmed or timeout occurs An exit alarm message is sent to the central station Restoral of an exit alarm will also be sent when the system is disarmed e The EXIT ALARM display etc will also result if an alarm from an exit or interior zone occurs within two minutes after the end of an exit delay In any of the previous cases use a second OFF sequence code plus OFF
96. he list below The example on the left shows zone type 03 Perimeter entered this is the default for zone 4 04 Zone Type Zone Types 00 Zone Not Used 08 24 Hr Aux 01 Entry Exit 1 09 Fire 02 Entry Exit 2 10 Interior w Delay 03 Perimeter 15 24 Hr Medical Personal Emergency 04 Interior Follower 120 Arm Stay 5800 05 Trouble Day Alarm Night 21 Arm Away RF 06 24 Hr Silent 22 Disarm Only 07 24 Hr Audible 23 No Alarm Response Do not use in UL installations You must enter 00 as the zone type for any hard wired zones that are not used When the display shows the zone type you want press to continue The report code consists of 2 hexadecimal digits each in turn consisting of 2 numerical digits For example for a report code of 3C enter 0 3 1st 03 2nd 12 3C for 3 and 1 2 for C Refer to the System Communication section for complete information on report codes if necessary 04 Report Code Enter the desired report code and then press to continue 4 3 FA147C Installation Instructions Typical summary display Zn ZI RC In L A summary display will appear showing the data for the zone that was just programmed Ce es If it is programmed satisfactorily press to continue n The next request is to enter Alpha descriptors for the zones The entry Program Alpha may be done now enter 1 or may be done at a later time using 82
97. hone line may result in the devices not ringing in response to an incoming call In most but not all areas the sum of the RENs should not exceed five 5 0 To be certain of the number of devices that may be connected to the line as determined by the total RENs contact the telephone company to determine the maximum REN for the calling area Continued 20 1 FA147C Installation Instructions 20 2 Federal Communications Commission FCC Part 68 Statement Continued If this equipment causes harm to the telephone network the telephone company will notify you in advance that temporary discontinuance of service may be required If advance notice is not practical the telephone company will notify the customer as soon as possible Also you will be advised of your right to file a complaint with the FCC if you believe necessary The telephone company may make changes in its facilities equipment operations or procedures that could affect the operation of the equipment If this happens the telephone company will provide advance notice in order for you to make the necessary modifications in order to maintain uninterrupted service If trouble is experienced with this equipment please contact the manufacturer for repair and warranty information If the trouble is causing harm to the telephone network the telephone company may request you remove the equipment from the network until the problem is resolved There are no user serviceable compon
98. ial number entered into the control e Button type transmitters e g 5802 5802CP 5804 5804BD should be periodically tested by the user for battery life Receiver Supervision The receiver itself is supervised A tamper report zone 9 will be generated a Ifcommunication with the receiver is interrupted or b Ifvalid RF signals are not received within 12 hours from at least one supervised wireless transmitter if any are included in the system Wireless System Installation Advisories Disregard the following advisories if the receiver is mounted in the control cabinet as described in the Installing The Control section 1 Place the receiver in a high centrally located area for best reception Do not place receiver on or near metal objects This will decrease the range and or block transmissions Do not mount receivers or transmitters in an attic where extreme temperatures could prevent proper operation 2 The RF House ID Code must be entered in field 24 for the receiver applies only if using a 5827 5827BD wireless keypad or 5804BD wireless key in the 5800 RF system Installation and Setup of the 5881 Wireless Receiver 6 2 1 Mount the receiver as indicated in the Installing The Control section if not installed previously in the control cabinet If the receiver is to be mounted outside the cabinet install it in its desired location see advisories above Receivers can detect signals from transmitters within a nomin
99. ice Type Description Wireless Panic UR or RF e Has four pushbuttons each with a unique Transmitter input loop code Programmable responses e g Panic Arm Stay Arm Away Disarm etc Pendant BR Only Has single pushbutton Personal Usually programmed for response type of Emergency 24 Hr Audible or 24 Hr Silent other zone Transmitter responses are possible Contains a non replaceable battery At the end of the battery s life the entire unit must be replaced 5802CP Belt Clip Personal BR Only Same as 5802 e See 5802MN Miniature UR or RF e Has single pushbutton Personal e Usually programmed for a response type of Emergency 24 Hr Audible or 24 Hr Silent other zone Transmitter responses are possible Wireless Key BR Only e Has four pushbuttons each with a unique Transmitter input loop code e Programmable responses e g Arm Stay Arm Away Disarm etc 5804BD Bi Directional e House ID must be set Wireless Key e Requires 5800TM Transmitter Module e Can indicate system status via its 2 LEDs and built in sounder e Has four pushbuttons each with a unique input loop code e Operates the system similarly to wired keypads 5806 Wireless 5807 Photoelectric 5808 Smoke Detectors e One piece smoke detectors with a built in transmitter 5816 Low Temperature TEMP Sensor 5817 Multi Point Universal Transmitter e Transmits a fault condition when temperature drops below 4500F e Has three u
100. ill be sent to the alarm monitoring station in the event that the telephone lines are out of order alarm signals are normally sent over the phone lines if connected to an alarm monitoring station Section 1 Section 2 Section 3 Section 4 Section 5 Section 6 Table Of Contents General DESCHIPHON irrena areren e E EEA a Epeei eaaa reiil 1 1 installing The Control gilera a 21 Mounting the Cabinet asleep aa 2 1 Installing the Lock if used micia rile i illa lalla 2 1 Installing the Control s Circuit Board Alone or if used With a 4204 4219 or 4229 Module i 22 Installing Control and RF Receiver Circuit Boards Together in the Cabinet 2 3 Standard Phone Line Connections ii 24 Wiring the AC Transformer i 24 Installing the Back Up Battery i 2 5 Earth Ground Connections iii 2 5 Installing Remote KeypadS i 3 1 General Tn formation eera eeir eeri orrera neer rni E ETAR SEEE E SEENE EPEAN EEEREN ria eels 3 1 Keypads that May Be Used uasmmssesrrsersrrsrsrsrersrree cceeseaececsssaeeecsssaeecseaae seesesaeeecesaaeeeenenaes 31 Winne tothe Keypad oces iio eniri ea aN AN AKEE AE E air 31 Wiring Run Chart for Devices Drawing AUX Power From the Control 3 2 Mounting the Keypads inrer iee EA LEI Ai 3 2 Using A Supplementary Power Supply To Power Additional Keypads 3 2 Preliminar
101. ime all sirens and all continuous keypad sounds will be shut off You may have to connect a 4204 or 4229 relay module when using an AAV unit If so do not use relay output number 1 for any other usage Wiring Connections For A Non Ademco AAV Unit Generally the method used to trigger an AAV unit is via the use of a 4204 or 4229 relay module Contact the manufacturer of the AAV unit for information regarding the wiring of their unit to the FA147C The control requires that the AAV module trigger type is falling edge FA147C Installation Instructions Programming 1 Atleast one 2 line Alpha keypad FA550KP must be connected to the keypad terminals on the control and the system powered up 2 Enter the programming mode by keying the following on the Alpha keypad INSTALLER CODE 8 0 3 Press 91 OPTION SELECTION Enter 4 or 6 for AAV monitoring See the Data Field Descriptions section or the Programming Form in the separate Programming Guide for detailed information on the available selections Note Options 2 4 6 and 8 cannot be used in UL installations 4 Relay programming in field 80 If a relay module is being used do not program anything for Relay 1 5 Exit the programming mode by keying 99 SECTION 12 Final Power Up In This Section General Information Earth Ground Connections AC Power Up Connecting the Back Up Battery Auxiliary Device Current Draw Worksheet Genera
102. ing 82 menu mode Program Alpha See the Alpha Description Programming section for specific procedure If 0 No was entered above the system will display a Enter Zn Num prompt for entry of the next wired expansion zone number 00 Quit 11 Proceed with the programming for the next zone as indicated previously Enter next zone number When all wired expansion zones are programmed satisfactorily exit 56 mode at the Enter Zn Num prompt by pressing 0 0 Exit the programming mode by keying 99 Proceed to the check out procedure that follows Check Out Procedure For Wired Expansion Zones After you have completed installation of all devices all wired expansion zones should be checked as follows 1 Make certain that all devices and sensors connected to the wired expansion zones are not in a faulted state Doors and windows with contacts should be closed PIRs should be covered use a cloth to mask them temporarily if necessary With all zones intact including hard wired zones the Alpha keypad connected to the system should display DISARMED READY TO ARM If the following is displayed DISARMED Press x to show faults press the key to display the faulted zone s Restore any faulted zone s as necessary also make sure that you have connected a 1000 ohm EOL resistor across the terminals of unused expansion zones on the 4219 or 4229 module When the READY TO ARM mes
103. ing a Transmitter Serial Number From a Zone in 56 Mode _ 6 12 Relay Outputs and X10 Type Module Usage in 7 1 Relay Device Basics i abi Lo ALIA nish need eee el eas 7 1 4204 and 4229 Relay Module Connections iii 7 1 4204 4229 Setupi tio an lA IONE IL Si 7 1 SUPErVISIONI 2 0 a Dura Bived Siw ne al la ees 7 2 Using an X10 Type Module PF284 ri 7 2 Programming Options Defined ii 7 3 Programming Output Relays i 7 5 Example of Output Relay Programming ii 7 6 Programming For an X10 Type Module PF284 ei TA Programming For Chime By Zone ii 7 10 FA4285 Phone Module mssesesrersrrererererererrnsrr rrrerrrrnrnrsrsrsr er er error KeA Bes KR rs rer ere Rear enn 8 1 Mounting the FA4285 Phone Module cessececeeaeceseaaececseaaecens bonne rn nn nn 8 1 General Imforimation sorsien svatensacedensshsl etai ES OANE EEA EED TN ENAN aE Shea ESR 8 1 Phone Module Wiring ii 8 2 Caller TD UNITS uretan aaa Riese acres eee tase riale persa 8 2 Programming The Control For Phone Access cssececsssaeeecnesaeeeessaaes 84 Checking the Operation of the FA4285 Phone Module 8 5 External SOUNdErs ilaele alias 9 1 Compatible Sounders iii 9 1 SOUNAEr Connections
104. ion begins upon any alarm in an assigned zone in the zone list Event EV 1 e FAULT Relay action begins upon any opening or short in an assigned zone in the zone list Event EV 2 e TROUBLE Relay action begins upon any trouble condition in an assigned zone in the zone list Event EV 3 e NOT USED Relay action is not dependent upon one of the above events Event EV 0 FA147C Installation Instructions 7 4 B 1 STOP STP A 1 B 1 ZONE LIST ZL is a group of zones to which the EVENT applies in order to activate a particular relay Note that there are a total of 3 zone lists that can be programmed in 81 mode when the selected EVENT Alarm Fault or Trouble occurs in any zone in the selected Start ZONE LIST 1 2 or 3 activation of the selected relay will START ZONE TYPE SYSTEM OPERATION ZT If a System Operation such as DISARMING 22 or ANY FIRE ALARM 39 is to activate the relay the appropriate choice would also be entered under the ZONE TYPE option ZONE TYPE is used independently of the EVENT ZONE LIST combination If a specific ZONE TYPE is chosen any zone of that response type going into alarm trouble or fault will cause the relay to activate as selected in ACTION If the same ZONE TYPE is also chosen for the STOP programming any zone of that type that restores will de activate the relay If a SYSTEM OPERATION is
105. is provided on a previous page Press to continue 10 Input Dev LP ol RF Trans RF Loop Number The cursor should now be flashing above the loop number The default is 1 To accept this press If a different loop number is being used on this transmitter enter the loop number 1 4 See the loop designations for various transmitters in the separate Programming Guide The loop number must be entered here whether using Zone Programming or Sequential Mode to enroll transmitters Press to continue 10 Learn S N 0 No 1 Yes 0 If the transmitter s serial number has not been previously enrolled you may enter the enrolling mode now by either entering 1 Yes or by pressing the upper left hand button of the program tool If using the program tool move to the physical location of the transmitter to be enrolled before pressing the button A single short beep will verify that the button has been pressed The system will respond to the first serial number transmitted after the key on the keypad or the button of the program tool is pressed Enter 0 No if you wish to enroll the transmitter later using the sequential mode in the Sequential Mode section later in this manual If 0 is entered go to step 13 skip steps 11 and 12 10 Input S N L A X X X X X XX The above prompt is displayed if 1 Yes is entered in response to the Learn S N prompt The serial number may be enrolled by o
106. ive anus ca Aone anus TELEPHONE LINE AT TELCO JACK BEFORE iw CALCULATIONS EOLR EOLR EOLR EOLR EOLR EOLR SERVICING THIS UNIT amp memore DAAM LOOR RESTARE EACAZONE Seo HS PLUS EOLA THIS EQUIPMENT SHOULD BE INSTALLED IN at ALARM OUTPUT KEYPAD ZONE 3 CAN BE PROGRAMMED FOR N C SENSOR FAST RESPONSE TO AN ACCORDANCE WITH THE NATIONAL FIRE 5 10 5 13 8VDC 2A MAX OPEN NOMINAL 10MSEC PROTECTION ASSOCIATION S STANDARD 72 600mA MAX FOR UL USAGE REMOTE KEYPADS ZONES 1 6 CAN BE PROGRAMMED FOR USE AS FIRE ZONES INCLUDING AUX POWER Ari RE CHAPTER 2 NATIONAL FIRE PROTECTION STEADY FOR BURGLARY PANIC TEMPORAL PROGRAMMED WITH AN THIS DEVICE COMPLIES WITH PART 15 OF FCC RULES OPERATION IS ASSOC BATTERYMARCH PARK QUINCY MA SOUNDING FOR FIRE e g USE ADEMCO No 740 SOUNDER Nos 702 OR 719 SIREN OR 12V BELL CONNECTION OF THE FIRE ALARM SIGNAL TO A FIRE ALARM HEADQUARTERS OR A CENTRAL STATION SHALL BE PERMITTED ONLY WITH THE PERMISSION OF THE LOCAL AUTHORITY HAVING JURISDICTION THE BURGLAR ALARM SIGNAL SHALL NOT BE CONNECTED TO A POLICE EMERGENCY NUMBER ALL OUTPUT CIRCUITS ARE POWER LIMITED Id SUBJECT TO THE FOLLOWING TWO CONDITIONS 1 IT MAY NOT CAUSE HARMFUL INTERFERENCE 2 IT MUST ACCEPT ANY INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION FA550KP BUT NEED NOT REMAIN IN SYSTEM AFTER PROGRAMMING THE SYSTEM CAN USE FA210KP 30mA FA245KP 30mA FA250KP 120mA OR FA550KP 140mA MULTIPLE KEYPADS MAY BE US
107. key to clear the keypad display Trouble Conditions See Troubleshooting Guide also 17 4 General Information The word CHECK on the keypad s display accompanied by a rapid beeping at the keypad indicates that there is a trouble condition in the system The audible warning sound can be silenced by pressing any key Instruct users to call for service immediately upon seeing any of the following messages Section 17 System Operation Check and Battery Displays e A display of CHECK and one or more zone numbers indicates that a problem exists with the displayed zone s and requires attention e A display of CHECK and 09 indicates that communication between control and a zone expander or wireless receiver is interrupted Check the wiring and DIP switch settings on the units e If there are wireless sensors in the system the CHECK condition may also be caused by some change in the environment that prevents the receiver from receiving signals from a particular sensor e Adisplay of BAT Fixed word keypads or SYSTEM LO BAT Alpha keypads with no zone number indicates that the system s main standby battery is weak e A display of BAT Fixed word keypads with a zone number and a once per minute beeping at the keypad indicates that a low battery condition exists in the wireless sensor displayed zone 00 indicates a wireless keypad If the battery is not replaced within 30 days a CHECK display may o
108. keying Installer code 8 0 Fields 40 41 42 44 Enter up to the number of digits shown Do not fill unused spaces Enter 0 9 11 for 12 for 13 for a pause 2 secs Press 40 PABX ACCESS CODE Enter up to 6 digits if PABX is needed to access an outside line If fewer than 6 digits are needed to be entered exit by pressing and next field number e g 41 To clear entries from field press 40 Press 41 PRIMARY PHONE No Enter up to 20 digits If fewer than 20 digits entered exit by pressing and next field number e g 42 To clear entries from field press 41 Press 42 SECONDARY PHONE No Enter up to 20 digits If fewer than 20 digits entered exit by pressing and next field number e g 43 To clear entries from field press 42 If using the Paging feature enter the pager number as the secondary phone number 15 3 FA147C Installation Instructions 15 4 Press 43 SUBSCRIBER ACCOUNT No Note Field 43 is also used as the Long Range Radio Subscriber Account Number Central Station Account Number Enter 0 9 11 for B 12 for C 13 for D 14 for E 15 for F default Enter 0 as the first digit of a 4 digit account number for Nos 0000 0999 End field by pressing and press next field number To clear entries from field press 44 See the blank Programming Form in the separate Programming Guide for examples of Account No en
109. l Information In previous sections you temporarily powered the system down and up again for the purpose of wiring programming and testing This section provides information about final power up procedures and battery size calculations Earth Ground Connections The designated earth ground terminal 21 must be terminated in a good earth ground for the lightning transient protective devices in this product to be effective See the Installing The Control section earlier in this manual AC Power Up 1 Plug the AC transformer permanently into a 24 hour uninterrupted 120VAC outlet 2 Following power up AC dI disabled or Busy Standby Alpha keypads or NOT READY fixed word keypads will be displayed Also the green READY LED on the keypad s should light After approximately 1 minute the initial displays will revert to DISARMED READY TO ARM for Alpha keypads or READY for Fixed word keypads if there are no faulted zones This 1 minute delay allows PIRs etc to stabilize To bypass this delay press 0 Note If you do not get the Ready displays described above make sure that there are no faulted zones doors windows open PIRs activated etc If necessary refer to Trouble Conditions in the System Operation section and also to the Trouble Shooting Guide section Connecting The Back Up Battery In the event of an AC power loss the control panel is supported by a back up rechargeable gel cell batte
110. lectronic components could fail at any time The most common cause of an alarm system not functioning when an intrusion or fire occurs is inadequate maintenance This alarm system should be tested weekly to make sure all sensors and transmitters are working properly The security keypad and remote keypad should be tested as well Wireless transmitters used in some systems are designed to provide long battery life under normal operating conditions Longevity of batteries may be as much as 4 to 7 years depending on the environment usage and the specific wireless device being used External factors such as humidity high or low temperatures as well as large swings in temperature may all reduce the actual battery life in a given installation This wireless system however can identify a true low battery situation thus allowing time to arrange a change of battery to maintain protection for that given point within the system Installing an alarm system may make the owner eligible for a lower insurance rate but an alarm system is not a substitute for insurance Homeowners property owners and renters should continue to act prudently in protecting themselves and continue to insure their lives and property We continue to develop new and improved protection devices Users of alarm systems owe it to themselves and their loved ones to learn about these developments FA147C Installation Instructions A 2 NOTES 24 HR BATTERY STANDBY REQUIR
111. lies 12V 500mA Use a UL Listed battery backed supply for UL installations The 487 12 488 12 power supplies have a backup battery which can power these keypads in the event of AC power loss Keypads powered from supplies which do not have a backup battery will not function when AC power is lost Therefore be sure to power at least one keypad from the Control s auxiliary power output Section 2 Installing the Keypads Connect the additional keypads as shown in Figure 3 2 using the keypad wire colors shown Be sure to observe the current ratings for the power supply used the keypad blue wire if present Make connections directly to the screw terminals as shown in Figure 3 2 Make no connection to Be sure to connect the negative terminal on the Power Supply unit to terminal 4 AUX on the control SUPPLEMENTARY CONTROL POWER SUPPLY TERMINAL STRIP a AUX AUX DATA DATA GS OUT IN A IMPORTANT x W w MAKE THESE w j j ju CONNECTIONS a lt z 3 DIRECTLY TO Zz je Z Ja a 5 SCREW TERMINALS a e 5 P a alalal AS SHOWN a a a Q C lt e jc e x gt gt gt gt gt gt gt gt LU LU LU LU LU LU LU LU z x x a pa ojojo O oO oO oO E FIEF E Pe FP FE Figure 3 2 Using A Supplementary Power Supply For Keypads Preliminary Check out Procedure If you want to check that the sy
112. ller ID function may not work Section 8 FA4285 Phone Module FA4285 WIRING NOTES Wire the FA4285 Phone Module exactly as shown using a direct connect cord and RJ31X jack 2 If Touch tones are not heard when pressing keys following phone access to the security system via an on premises phone try reversing the pair of wires connected to terminals 3 amp 4 on the FA4285 and the pair of wires connected to terminals 17 amp 18 on the control If an error signal fast busy signal is heard when trying to access the system via the phone check for correct line seizure wiring as described in note 4 Connection to the incoming Telco line via a RJ31X jack CA88A in Canada and direct connect cord as shown in this diagram is essential even if the system is not connected to a central station The FA4285 will not function if this is not done The house phone lines gray and brown wires must be wired to the Phone Module terminals not to the control terminals Otherwise an error signal fast busy signal will occur when trying to access the system from an on premises phone If the telephone system on the premises includes a stand alone Caller ID unit connect the ID unit directly to the Handset terminals 17 amp 18 on the control as shown Incoming Handset Telco Line GROUND TERM TERMINALS ON CONTROL CONNECT TO EARTH GROUND COLD WATER PIPE ETC INCOMING TELCO LINE a CALLER ID
113. n consists of both the method of communication between the control panel and the central station receiver and the actual way the information is sent and displayed at the central station Report Code Formats When the panel calls the central station receiver it waits to hear a handshake frequency from the receiver to confirm that the receiver is on line and ready to receive its message Once the panel hears the handshake it is programmed to listen for it sends its message The panel then waits for a kissoff frequency from the receiver acknowledging that the message was received and understood If the handshake frequency is not given or is not understood by the panel the panel will not send its message Once the handshake frequency is received and understood by the panel the panel will send its message If there is an error in the transmission the receiver does not receive a valid message the kissoff frequency will not be given by the central station receiver The panel will make a total of eight attempts to the primary telephone number and eight attempts to the secondary telephone number if programmed to get a valid message through If the panel is not successful after its numerous attempts the keypad will display COMM FAILURE Alpha keypad or FC Fixed word keypad The following chart defines the three sets of handshake kissoff frequencies that the panel supports and the different formats that can be sent
114. n see the instructions supplied with the 4219 and 4229 RELAY lt DIP SWITCH 4229 2 FOR SETTING ADDRESS AND ZONE A RESPONSE EITHER OR BOTH CAN BE USED A RELAY f 3 NO C NC 4 PIN CONSOLE PLUG OFF4 gt ON TERMINALS ON CONTROL PANEL GRN DATA OUT TAMPER JUMPER POSITION TO CONTROL TERM 6 4229 IN CABINET AGUNG TERM DIP SWITCH NOT TAMPERED o 5 GRO gt 4 T e 4229 REMOTE gt gt TAMPER PROTECTED TBI ol 12V TERMS oo o bed YEL DATA IN ZZ0Z o oji TERM 7 Ie SNS NINE DAN CONTROL Figure 5 1 RLY RY REED TERMINATE EACH Wiring zoo ec RIERS SWITCH END OF LINE RESISTOR Connections od EACH ZONE S MAX e OOP RESISTANCE 4219 amp 4229 300 OHMS E O L ZONES A B cC D E F G H 4229 shown 5 1 FA147C Installation Instructions Programming Wired Expansion Zones 1 At least one 2 line Alpha keypad FA550KP must be connected to the keypad terminals on the control and the system powered up 2 Enter the programming mode by keying the following on the Alpha keypad Installer code 3 5 19 8 0 EXPANSION RELAY USED must be programmed as required before continuing See the 4 If RF zones or wired expansion is used data fields 22 RF SYSTEM TYPE and 25 WIRED Programming Form in the separate Programming Guide 8 Press 56 Note that this is an int
115. n er en nr renen aren caseeeeseeees 13 1 General Information ii 13 1 Assigning Zone Descriptors st iaia 13 1 Entering Zone Descriptors in program Menu Mode 82 i 13 1 Programming the Descriptors i 13 1 Adding Custom Words uri Gnna andai ea aa a 13 3 Alpha Vocabulary List For Entering Zone Descriptors eeeeeeeeees 13 5 Character ASCI1 Chatteris oit n a a e ripiego 13 5 Section 14 Sequential Mode For 5800 TransmitterS i 14 1 Section 15 System Communication nsseserersrrrrrersrrrrrenrrrr ii 15 1 Report Code Formali saracii ii aA A an nba aa RDR ANAR RER AEA 15 1 Table of Contact ID Event Codes ceeeseneceeneeceseeeaeceeaaececeeeeaeees 15 3 Communication Programming iii 15 3 Section 16 Testing The System 16 1 Test Procedure tir ana I ea Ana ari 16 1 To the Ins taller isos cece ces dio alla Aa ca Cee Bs PO age NS AN PERG Raa E N 16 1 Section 17 System Operation m smmmsesersrsrsrrrsrersrsrerr cscscessesesecssesecsecsessesees susesseeecsaesecseeseeseeeseeeee eens 17 1 Security Codes ses asia liana ete vec tte hos CARS KRA VAS SAS A BR RA NAS n 17 1 Installer Cod sessessssvolssectesnenores sens Nisser nt delgi aerea 17 1 Assigning the Master Cod cain e Keven eee 17 1 Changing the Master Code aa ee 17 1 User Codes rina IA SRS SR E E tan oT RARE 17 1 Duress Codes arnie ai Danco
116. nctioning Transmitter No zone not programmed 5881 address incorrect Field 22 not set properly Transmitter zone type ZT is set to 00 Not Used Transmitter battery not installed 5800 System transmitter serial No not entered in system Bat or System Lo Bat no zone Nos Bat 00 Fixed word keypad display KYPD LB 00 Alpha keypad display Bat or Lo Bat nn System is in TEST mode A wireless transmitter low battery has occurred and is displayed A supervision CHECK has occurred Put control in TEST mode If zone does not respond try operating the tamper switch or another input to the transmitter 5a 5b If another input causes the zone to be displayed the wrong loop input was entered when programming If no response at all from this transmitter this physical transmitter has not been entered into the system Check or change transmitter s battery Check the control s AC power Check code switches inside transmitter Must match with RF House Code programmed in control Move transmitter or 5881 Check for large metal obstructions then relocate transmitter if necessary Verify by activating 5881 with another similar transmitter If O K now return defective transmitter Verify by making sure other transmitters cannot activate 5881 If defective replace and return original 5881 Verify programming Set DIP switch for address 0 Set field
117. nding the number of wired zones in the system describes the modules that can be used and their wiring connections plus a procedure for programming the wired expansion zones Installing Zone Expansion Units You can add an additional 8 wired expansion EOLR zones to the basic control s 8 hardwired zones for a total of 14 wired zones by using a No 4219 Wired Expansion Unit or 4229 Wired Expansion Relay Unit Location e You can mount an expansion unit within the control cabinet if space permits Otherwise mount the unit outside the cabinet Supervision e Units are supervised against removal Keypads will display CHECK and zone 09 if a zone expander is disconnected e Units have tamper protection for security when mounted outside of the cabinet Zone Information Assign zone numbers 10 17 for the eight wired expansion loops designated A to H You can program these zones individually in 56 interactive mode as indicated in Programming Wired Expansion Zones later in this section Connections and Set Up 1 Connect the 4219 or 4229 module to the control s keypad terminals see Figure 5 1 2 Set the 4219 or 4229 s DIP switch for device address 1 switch 2 OFF and switches 3 4 5 ON Switch 1 determines expansion zone A s response time ON normal response OFF fast response For location of the DIP switch in the unit see Figure 5 1 location of DIP switch for both units is in the same location For additional informatio
118. ne and an FA4285 Phone Module is included in the installation you should note the following When calling in from an off premises phone to receive a status report or execute a command the user should make the initial call allow 1 to 3 rings only and hang up Then call in again the Phone Module will now seize the line and 2 long tones will be heard followed by the usual voice prompt for the 2 digit phone access code If this procedure is not followed Phone Module operation will not be possible Press 96 INITIALIZE DOWNLOAD ID AND SUBSCRIBER ACCT No FOR DOWNLOADING No data entry required This completes the communication programming Exit the programming mode by keying 99 Refer to the Testing The System section to check system operation 15 8 In This Section SECTION 16 Testing the System Test Procedure To the Installer Test Procedure After installation is completed the Security System should be carefully tested as follows 1 With the system powered up and in the disarmed state check that all zones are intact If a NOT READY message is displayed press the key to display the faulted zone s Restore faulted zone s if necessary so that the READY message is displayed Fault and restore every sensor individually to ensure that it is being monitored by the system Enter the security code and press the TEST key The external sounder will sound for 1 second The keypad should sound 3 beep
119. ne of two methods a Enter the 7 digit serial number printed on the transmitter using an alpha keypad or b Activate the transmitter by faulting or restoring the input you wish to use for that zone e g press a button open or close a door etc 6 9 FA147C Installation Instructions 6 10 12 13 The system will enroll the serial number of the first transmitter heard add the loop number entered to this serial number display the serial and loop numbers and cause the keypad to beep twice 10 Input S N L A002 4064 1 If the serial and loop number combination is already present in the system a single long beep will be heard from the keypad If this happens the system will not display the serial number but will wait for a transmission from another transmitter or transmitter loop input The system will then enter an optional confirmation mode so that the operation of the actual programmed input can be confirmed Activate the loop input or button that corresponds to this zone We recommend that you confirm the programming of every transmitter before proceeding to the next zone When the system sees activity on the appropriate input it will beep three times and display the confirmation message 10 Confirmed A022 4064 1 At any time during this step you may press the key on the keypad or the upper left hand button of the program tool if you are satisfied with the serial and loop number combination that
120. ned to each terminal device denotes the percentage of the total load to be connected to a telephone loop which is used by the device to prevent overloading The termination on a loop may consist of any combination of devices subject only to the requirement that the total of the Load Numbers of all the devices does not exceed 100 AVIS L tiquette du minist re des Communications du Canada identifie le mat riel homologu Cette tiquette certifie que le mat riel est conforme certaines normes de protection d exploitation et de s curit des r seaux de t l communications Le minist re n assure toutefois pas que le mat riel fonctionnera la satisfaction de l utilisateur Avant d installer ce mat riel l utilisateur doit s assurer qu il est permis de le raccorder aux installations de l entreprise locale de t l communications Le mat riel doit galement tre install en suivant une m thode accept e de raccordement Dans certains cas les fils int rieurs de l entreprise utilis s pour un service individuel a la ligne unique peuvent tre prolong s au moyen d un dispositif homologu de raccordement cordon prolongateur 20 3 FA147C Installation Instructions 20 4 t l phonique interne L abonne ne doit pas oublier qu il est possible que la conformit aux conditions nonc es ci dessus n emp che pas la d gradation du service dans certaines situations Actuellement les entreprises de t l communications ne permettent
121. nent parts Recommendations must be included for a specific program of frequent testing at least weekly to insure the system s proper operation at all times SECTION 17 System Operation In This Section Security Codes Keypad Functions FA4285 Phone Module Relay Outputs Exit Alarm Displays Trouble Conditions Security Codes Installer Code The installer programs the 4 digit Installer Code initially as part of the programming procedure The factory default Installer code is 3 5 1 9 but may be changed in field 20 Note The Installer Code is defined as User 1 The Installer code is the only code that can allow re entry into programming mode In normal operation mode only the Master code can be used to enter the User codes refer to Assigning the Master Code See Mechanics Of Programming section in the separate Programming Guide for details on exiting the programming mode via 98 or 99 Assigning the Master Code In normal operation mode assign the 4 digit Master Code as follows Installer Code 8 2 4 digit Master Code Note The Master Code is defined as User 2 Changing the Master Code In normal operation mode the Master code can be changed by entering Master Code 8 2 New Master Code New Master Code again User Codes In normal operation mode the Master security code can be used to assign up to 5 secondary users 4 digit security codes Users 8 8 It can also be use
122. ng STT 3 1 1 33 Press the key to continue This screen again displays a summary of the current STOP programming Press the key to continue Enter 0 0 to end programming for the X10 type module Previously entered data can be reviewed by pressing 8 0 After the relay number is chosen press to go to the next screens This is a review mode only and data cannot be changed In the example of programming above the X10 module will be activated and close and stay closed regardless of the selection made for ACTION A when any burglary alarm occurs in any of the zones that are listed in Zone List 1 Refer to Zone List programming on previous page The X10 module will be de activated and open when the system is disarmed System Operation choice 22 Summary Of Programming for X10 Type Module Example of relay 4 programming START STOP or botn gt either or both RELAY ZONE TYPE RESTORE of ZONE TYPE te ACTION EVENT LIST SYST OP N ZONE LIST SYST OP N EV ZL ZT ZL ZT 81 ZONE LISTS FOR OUTPUT RELAYS Refer to Zone List programming procedure on a previous page om Io ae els Example Any burglary alarm occuring in zones 10 11 or 12 shown entered in Zone List 1 in menu mode 81 will START X10 action disarming will STOP X10 action Zone List 1 Started or stopped by zone numbers selected
123. ning Zone Descriptors Adding Custom Words Alpha Vocabulary List ASCI Character Chart General Information xh This section provides instructions for programming Alpha descriptors This is recommended for systems using Alpha keypads and necessary if an FA4285 Phone Module is used Alpha descriptors cannot be displayed on fixed word keypads If using an FA4285 Phone Module select from those words in the Alpha Vocabulary list on a following page shown in boldface type The Phone Module will not provide annunciation of the other words If an FA4285 Phone Module is added to an existing FA147C system the Alpha descriptors presently in the system should be re programmed selecting from those words shown in boldface type in the Alpha Vocabulary list The Phone Module will not provide annunciation of any other words The ALPHA VOCABULARY LIST and CHARACTER CHART will be found on a following page Assigning Zone Descriptors The Alpha Keypad used with the FA147C can have a user friendly English language descriptor location of all protection zones keypad panics and RF receiver supervision faults programmed into the system Each descriptor can be composed of a combination of words up to a maximum of 3 selected from a vocabulary of words stored in memory the list is on a following page In addition up to 10 installer defined words can be added to those already in memory Thus when an alarm or trouble occurs in a zone an app
124. nique input loop codes one for a Primary contact loop with programmable options the others for two Auxiliary closed circuit contact loops Recessed Transmitter e Reed switch magnetic contact sensor that is easily concealed in the frame and edge of a door or window e Hasa single unique input loop code 5816 Door Window e Has two unique input loop codes one for 5816MN Transmitters a wired closed circuit contact loop the other for a built in reed switch used in conjunction with a magnet The 5816 and 5817 do not supervise their loop wiring for shorts Therefore for UL Household Burglary installations the loop wiring may not exceed 3 feet Continued 6 5 FA147C Installation Instructions Compatible 5800 Series Transmitters Continued Enter As Input Device Type moder Product Shock Processor Transmitter 5819WHS Shock Processor 5819BRS Transmitter Wireless Keypad 5827BD Wireless Two Way Keypad 5849 Glass Break Detector 5890 PIR Detector e Connects to externally mounted inertia type shock detector not supplied Has built in tampered cover switch Has 3 unique input loop codes Loop 1 Terminals for a wired N C sensor loop Loop 2 For a closed circuit contact loop using the built in reed switch in conjunction with a magnet Loop 3 Terminals for a wired closed circuit contact loop e Has built in shock sensor e Has built in tampered cover switch e H
125. o digit code see table that follows This example shows the Any burg alarm selection of Any Burglary Alarm 33 from System Operation as the START Event Press the key to continue Choices For Zone Type 00 Not Used 04 Interior Follower 08 24 Hr Aux 01 Entry Exit 1 05 Trouble Day Alarm Night 09 Fire 02 Entry Exit 2 06 24 Hr Silent 10 Interior w Delay 03 Perimeter 07 24 Hr Audible 15 24 Hr Medical Personal Emerg Do not use in UL installations Choices For System Operation 20 Arming Stay 33 Any Burglary Alarm 39 Any Fire Alarm 21 Arming Away 34 Code 7 Key Entry 40 Bypassing 22 Disarming 35 Code 8 Key Entry 41 AC Power Failure 31 End of Exit Time 36 At Bell Timeout 42 System Batt Low 32 Start of Entry Time 38 Chime 58 Duress Or at Disarming whichever occurs earlier 7 8 Section 7 Relay Outputs and X10 Type Module Usage If a zone list will be used to STOP or restore the action enter the zone list ZL number 1 2 or 3 to be programmed in 81 mode If not used enter 0 Press the key to continue If a zone type or system operation will be used to STOP the action enter the appropriate two digit code see the choices listed previously In this example Disarming 22 has been selected Press the key to continue 04 A EV ZL ZT This screen again displays a summary of the current START programmi
126. odule The length of all wire runs must not exceed 1500 feet 457m when unshielded quad conductor cable is used 750 feet if shielded cable is used This restriction is due to the capacitive effect on the data lines when quad cable is used KEYPAD CONNECTOR CABLE BLACK 9 RED GREEN KEYPADS YELLOW CONTROL TERMINALS Figure 3 1 Keypad Connections To The Control Board Mounting the Keypads 1 Make sure keypads are set to non addressable mode address 31 which is the factory default setting Refer to the instructions provided with the keypad for address setting procedure 2 Mount the keypads at a height that is convenient for the user Refer to the instructions provided with the keypad for mounting procedure You can either surface mount or flush mount keypads using an appropriate Trim Ring Kit FA550TRK except FA210KP FA245KP Refer to the mounting instructions and template included with the keypad and or trim ring kit for specific information Using a Supplementary Power Supply to Power Additional Keypads The control provides 500mA for powering keypads up to a maximum of 4 and other devices from the auxiliary power output The backup battery will supply power to these keypads in the event that AC power is lost When the control s auxiliary power load for all devices exceeds 500mA you can power additional keypads from a regulated 12VDC power supply e g 487 12 supplies 12V 250mA 488 12 supp
127. of the optical system can reduce their detection ability Passive Infrared Detectors sense changes in temperature however as the ambient temperature of the protected area approaches the temperature range of 90 to 1050F 32 to 40 C the detection performance can decrease e Alarm warning devices such as sirens bells or horns may not alert people or wake up sleepers if they are located on the other side of closed or partly open doors If warning devices are located on a different level of the residence from the bedrooms then they are less likely to waken or alert people inside the bedrooms Even persons who are awake may not hear the warning if the alarm is muffled by noise from a stereo radio air conditioner or other appliance or by passing traffic Finally alarm warning devices however loud may not warn hearing impaired people e Telephone lines needed to transmit alarm signals from a premises to a central monitoring station may be out of service or temporarily out of service Telephone lines are also subject to compromise by sophisticated intruders e Even if the system responds to the emergency as intended however occupants may have insufficient time to protect themselves from the emergency situation In the case of a monitored alarm system authorities may not respond appropriately e This equipment like other electrical devices is subject to component failure Even though this equipment is designed to last as long as 20 years the e
128. ogram Tool 0 No 1 Yes Enter 0 No The next prompt will ask you to enter zone number 42 Section 4 Basic Hard Wired Zones 1 6 Enter the first zone number that you wish to program or 0 0 to exit zone programming If you are starting with zone 1 leave as is and 00 Quit press to continue Enter Zn Num If programming another zone enter the desired zone number 02 03 Default Z Numb i A oe ae etc zone 04 is shown in the next display Press to continue after entering 56 Typical summary display A summary display will appear showing the present status of that zone s programming Zn ZT RC In L Zn zone number 04 03 00 HW ZT zone type RC report code for that zone In input type of zone HW will be displayed Values displayed are currently programmed values The summary display at the left shows the default values except for zone number 4 shown entered its default zone type being 03 If programmed satisfactorily press to back up one step and enter the next zone number If you want to change a zone s programming press A prompt for Zone Type will appear Each zone must be assigned a zone type which defines the way in which the system responds to faults in that zone See Response Type Perimeter Definitions section in the separate Programming Guide for an explanation of each zone type Zone Type Enter the desired zone type code from t
129. one Relay Device Basics Relays are programmable switches that can be used to perform many different functions They can be used to turn lights on and off control sounders or for status indications In this system each relay must be programmed as to how to act ACTION when to activate START and when to de activate STOP Each of these is described below and in the programming procedure for 80 and 81 interactive modes that are provided at the end of this section The control supports the following relay modules 4204 Relay Module 4 relays 4229 Zone Expander Relay Module 2 relays The 4204 and 4229 relays provide Form C normally open and normally closed contacts 3 A 4204 cannot be used if a 4219 or 4229 is already being used In 80 and 81 interactive modes a series of keypad prompts will request entries for programming of the Relay outputs used in the system Refer also to OUTPUT RELAYS WORKSHEET FOR FIELDS 80 AND 81 in the blank programming form provided in the separate Programming Guide 4204 and 4229 Relay Module Connections 4204 4229 Setup The 4204 unit can be mounted either remotely or in the control panel The following steps should be taken to properly set up the 4204 The control should be powered down while making wiring connections 1 Connect the 4204 or 4229 module to the control s remote keypad terminals 4 7 using the connector supplied with the module Use standard 4 conducto
130. onnected to a Long Rang Radio to report that an alarm has taken place and provide a cellular radio notification that this event has occurred You should refer to the Long Rang Radio s instructions for information on the required connection to the Long Range Radio Note that the Memory of Alarm trigger applies a ground when an alarm occurs and remains in this condition until the Memory of Alarm is cleared at the control Only alarms that activate an external sounder VOLTAGE TRIGGER PIN 2 MEMORY 3 PIN CONNECTOR OF ALARM SUPPLIED 2 lt TO LONG RANGE RADIO CELLULAR BACKUP 3 CONNECTION Figure 10 2 Using the Memory of Alarm Voltage Trigger With Long Range Radio 10 1 FA147C Installation Instructions Programming for Long Range Radio 1 At least one 2 line Alpha keypad FA550KP must be connected to the keypad terminals on the control and the system powered up Enter the programming mode by keying the following on the Alpha keypad INSTALLER code 8 0 Press 27 OUTPUT TO LONG RANGE RADIO Enter 1 when using a Long Range Radio enter 0 if not default is 0 If yes is selected any dialer report programmed to report to the PRIMARY phone number in field 47 will also be sent via long range radio All dialer and long range radio reports will be in Contact ID format regardless of the selection made in field 46 Full Trouble and Restore messages are sent Program the long range radio for device address 3
131. or improperly repaired or serviced by anyone other than First Alert Professional factory service For warranty service return product transportation prepaid to First Alert Professional Factory Service 165 Eileen Way Syosset New York 11791 THERE ARE NO WARRANTIES EXPRESS OR IMPLIED OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR OTHERWISE WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF IN NO CASE SHALL SELLER BE LIABLE TO ANYONE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY EXPRESS OR IMPLIED OR UPON ANY OTHER BASIS OF LIABILITY WHATSOEVER EVEN IF THE LOSS OR DAMAGE IS CAUSED BY THE SELLER S OWN NEGLIGENCE OR FAULT Seller does not represent that the products it sells may not be compromised or circumvented that the products will prevent any personal injury or property loss by burglary robbery fire or otherwise or that the products will in all cases provide adequate warning or protection Customer understands that a properly installed and maintained alarm may only reduce the risk of a burglary robbery fire or other events occurring without providing an alarm but it is not insurance or a guarantee that such will not occur or that there will be no personal injury or property loss as a result CONSEQUENTLY SELLER SHALL HAVE NO LIABILITY FOR ANY PERSONAL INJURY PROPERTY DAMAGE OR OTHER LOSS BASED ON A CLAIM THE PRODUCT FAILED TO GIVE WARNING HOWEVER IF SELLER IS HELD LIABLE WH
132. or vibrations 8 Repeated low battery signal Transmitter located where temperature drops below 3200F Poor quality or unspecified battery in transmitter Transmitter malfunctioning 9 Local bell and keypad sound 9 Exit or interior zone contained a fault at end of continuously after arming Exit Delay e g Exit door left open The Exit Alarm display etc will also result if an alarm from an exit or interior zone occurs within two minutes after the end of an exit delay amp amp amp eee ee 10 Communication between control and zone expander or wireless receiver is interrupted 10 CHECK and 09 displayed 11 External siren or bell does 11a not sound following an alarm Open or shorted wiring to external sounder 11b Sounder defective 12 External siren or bell does not sound for 1 second as soon as system is placed in Test mode 12a Same as 11a and 11b above Also back up battery may be discharged or not connected 13 Keypad displays Bell 13a Failure Alpha or Check 70 fixed word accompanied by rapid beeping Open or short in wiring to external sounder 13b Bell supervision not properly enabled Check with all occupants of protected premises Check programming of entry delays Check all openings for proper switch and magnet orientation Check wiring connections Be sure wires are properly stripped and are tightly fastened to screw te
133. ot exceed 600mA total STANDBY TIME see Table in the Final Power Up section 3 Communication FORMATS SUPPORTED 4 2 Ademco Express 10 characters sec DTMF Touch Tone Data Tones 1400 2300Hz ACK 1400Hz KISSOFF Ademco Contact ID Reporting 10 characters sec DTMF Touch Tone Data Tones 1400 2300Hz ACK 1400Hz KISSOFF 4 2 Ademco Low Speed Standard 10 pulses sec 1900Hz Data Tone 1400Hz ACK KISSOFF Radionics Standard 20 pulses sec 1800Hz Data Tone 2300Hz ACK KISSOFF Can report 0 9 B F Line Seize Double Pole Ringer Equivalence 0 7B FCC Registration No AC 398U 68192 AL E 4 Maximum Zone Resistance Zones 1 6 300 ohms excluding EOLR FA147C Installation Instructions FA210KP Remote Keypad 1 Physical 5 3 4 W x 4 3 4 H x 1 D 146mm x 121mm x 26mm 2 Electrical Voltage Input 12VDC Current Drain 30mA 3 Interface Wiring To control panel s keypad connection points RED 12VDC input aux power GREEN Data Out to Control YELLOW Data In from Control BLACK Ground FA245KP Remote Keypad Specifications the same as FA210KP Remote Keypad above FA250KP Remote Keypad 1 Physical 5 1 16 W x 6 3 8 H x 1 3 4 D 129mm x 162mm x 45mm 2 Electrical Voltage Input 12VDC Current Drain 120mA 3 Interface Wiring Same as FA210KP FA550KP Remote Keypad 1 Physical 5 1 16 W x 6 3 8 H x 1 3 4 D 129mm x 162mm x 45mm 2 Electrical Voltage Input 12VDC Current Drain 140mA 3 Int
134. output relays used in the system 4204 or 4229 modules Refer to the Programming Form worksheet in the separate Programming Guide for 80 Interactive Mode If field 25 has not been programmed for a 4204 or 4229 relay skip this field Output Relay Displays Upon pressing 80 this screen will appear Enter the Relay Number 01 02 03 or 04 for a 4204 or 01 or 02 for a 4229 or 00 to end these entries The key is used to accept an entry and advance to the next prompt The key is used to revert back to the last question to check or change an entry Press to go forward again Press the key to continue This screen displays a summary of the current Relay START programming for this example relay 02 has been selected Press the key to continue This screen displays a summary of the current Relay STOP programming Press the key to continue Enter the desired relay action as listed below 0 No response 1 Close for 2 seconds 2 Close and Stay Closed 3 Continuous Pulse on amp off 1 sec ON 1 sec OFF Press the key to continue Enter the event to START the relay 0 Not used 2 Fault 1 Alarm 3 Trouble A zone list must be used in conjunction with an event If a zone type system operation is to be used instead of an event enter 0 Press the key to continue If a zone list will be used to START the relay action enter the zone list number to be programmed in field 81 1 2
135. pas que l on raccorde leur mat riel aux prises d abonn s sauf dans les cas precis pr vus par les tarifs particuliers de ces entreprises Les r parations du mat riel homologu doivent tre effectu es pas un centre d entretien canadien autoris d sign par le fournisseur La compagnie de t l communications peut demander l utilisateur de d brancher un appareil la suite de r parations ou de modifications effectu es par l utilisateur ou cause de mauvais fonctionnement Pour sa propre protection l utilisateur doit s assurer que tous les fils de mise en terre de la source d nergie lectrique des lignes t l phoniques de r seau de conduites d eau s il y en a soient raccord s ensemble Cette pr caution est particuli rement importante dans les r gions rurales Avertissement L utilisateur ne doit pas tenter de faire ces raccordements lui m me il doit avoir recours un service d inspection des installations lectriques ou un lectricien selon le cas L indice de charge IC assign chaque dispositif terminal pour viter toute surcharge indique le pourcentage de la charge totale qui peut tre raccord a un circuit t l phonique boucl utilis par ce dispositif La terminaison du circuit boucl peut tre constitu e de n importe quelle combinaison de dispositifs pourvu que la somme des indices de charge de l ensemble des dispositifs ne d passe pas 100 Appendix A Warning The Limitations Of Thi
136. plus control of relay outputs Optional Long Range Radio e Allows all messages that have been programmed to go to the primary telephone number to be reported additionally to an Ademco 7720 PLUS or 7820 radio Alarm Output e Provides a 12VDC 2 AMP output that can drive the compatible sounders listed in the External Sounders section assumes a fully charged battery is connected e Steady output for Burglary Panic or temporal pulse sounding output for Fire notification as required by UL e Uses current limiting circuitry for protection e Provision for Bell supervision 1 2 Section 1 General Description Voltage Trigger for X10 Type Module 4 pin header serves as voltage trigger for an optional X10 type module PF284 or equivalent Keyed connector with flying leads is supplied for connection from header to X10 type module Requires use of relay module 4204 or 4229 which must be programmed appropriately as indicated in the instructions Memory of Alarm Voltage Trigger A 3 pin header serves as a voltage trigger for connection to an optional strobe light etc Will remain activated following any alarm that activates the external sounder until the system is disarmed Chime Chime by Zone Chime when on will normally sound when any entry exit or perimeter zone is faulted However a chime by zone option when programmed allows only specific zones to chime if they are faulted when the system is in the chime mode
137. pressing to accept the zone information the following will be displayed Program Alpha O NO 1 YES 0 14 Section 6 Wireless RF Zone Expansion 5800 RF Systems If you want to program alpha descriptors now enter 1 Yes See the Alpha Descriptor Programming section for more information If not enter 0 No This will bring you back to the Enter Zn Num prompt for the next zone When all zones have been programmed enter 00 to quit Enter Zn Num 00 QUIT 11 Next Zone number If you plan to enroll serial numbers in the sequential mode enter 00 to quit then go to the Sequential Mode section later in this manual to enroll the serial numbers using the system s TEST mode Do not use the Transmitter ID Sniffer mode for this as it will only A When you have finished programming all zones including all serial numbers test each zone check for transmission of one zone on a particular transmitter and NOT the zones assigned to each additional loop Check Out Procedure for Wireless Zones Go No Go Test Before mounting transmitters permanently conduct Go No Go tests to verify adequate signal strength and reorient or relocate transmitters if necessary During this mode wireless receiver gain is reduced by 50 Testing in this mode assists in determining good mounting locations for the transmitters and verifies that the RF transmission has sufficient signal amplitude margin for th
138. r twisted cable for long wiring runs 2 Set the 4204 or 4229 s DIP switch for a device address of 1 switch 2 OFF and switches 3 4 and 5 ON Switch 1 determines the unit s cover tamper response ON disabled OFF enabled DIP SWICH 3 Connect the desired field wiring to the unit s relay contact terminals See Figures 7 1 and 7 2 7 1 FA147C Installation Instructions Supervision The 4204 and 4229 modules are supervised against removal CHECK and zone 09 will be displayed if a module is disconnected from the control s keypad terminals 4 5 6 amp 7 4204 RELAY 4 Orc TYPICAL DIP SWITCH SHOWN OFF b2 i ne FOR SETTING DEVICE ADDRESS O OT No AND ENABLING DISABLING TAMPER c RELAY RELAY CONTACTS ARE NC NOT SUPERVISED COVER TAMPER REED SWITCH 4 PIN KEYPAD PLUG RELAY 2 EITHER OR BOTH CAN BE USED TB1 3 09 3 09 RELAY 1 O OOOOOOOO DATA IN FROM CONTROL Figure 7 1 GROUND DATA OUT 4204 Connections TO CONTROL to Control 12V RELAY CON RELAY DIP SWITCH 4229 NECTOR 5 2 E FOR SETTING ADDRESS AND ZONE A RESPONSE O e O EITHER OR BOTH CAN BE USED o RELAY e 1 J O Noce apn KEYPAD PLUG SE 3 GRN eee oe JOE PIER ERM ro He NOT TAMPERED o GROUND TERM 4 ElZlo Li Ewoo am se Oye e e YEL DATA
139. rent drawn from the alarm output and the auxiliary power output combined cannot exceed 600mA In addition the sounding device must be a UL Listed audible signal appliance rated to operate in a 10 2 13 8 VDC voltage range and must be mounted indoors Example Wheelock Signals Inc siren model 34T 12 provides 85dB A for NFPA 74 amp Standard 985 91 FA147C Installation Instructions Non UL Installations The total current drawn from the alarm output terminals cannot exceed 2 amps The back up battery must be connected when the sounder is tested since the current for the sounder is supplied by that battery Going beyond the limits indicated 2 amps will overload the power supply or may cause the electronic circuit protecting the sounder output to trip This control complies with NFPA requirements for temporal pulse sounding of fire notification appliances Temporal pulse sounding for a fire alarm consists of the following 3 pulses pause 3 pulses pause 3 pulses repeated Sounder Connections The control provides a 12 VDC output which can power external alarm sounders bells or sirens This output will activate a sounder when an alarm occurs The control should be powered down while making the following wiring connections Connect the external sounder to alarm output terminals 3 and 4 See Figure 10 1 Optional Bell Supervision This is a hardware enabled option If enabled and th
140. rity system via a Touch tone phone either on premises or by a call in when away The Phone Module can announce many of the same words that would normally be displayed on an Alpha keypad under the same system conditions e Only one Phone Module can be used in this security system e When using the FA4285 Phone Module keypads in the system must be set to the non addressable mode address 31 When properly connected the FA4285 Phone Module will enable the user to do the following via a Touch tone telephone a Receive synthesized voice messages over the phone regarding the status of the security system b Arm and disarm the security system and perform most other commands using the telephone keypad with voice annunciation being provided over the phone as confirmation after a command is entered The phone used for phone access must have Touch tone capability though Touch tone service is not necessary if premises uses PULSE dialing switchable phones must be set for Touch tone temporarily before attempting phone access A Phone Access User s Guide is provided with the Phone Module for the user of the system The Phone Module is not Listed for UL installation use Mounting The FA4285 Phone Module The Phone Module may be mounted in the control cabinet if space is available or if this is not possible on the side of the cabinet or adjacent to it When mounting the Module outside the cabinet use the screw holes at it
141. rminals Check and revise programming Re program transmitter number Mount magnet closer to magnet Change location Use magnetic contacts to protect opening Check battery Use only batteries specified does not apply to transmitters with non replaceable batteries Replace faulty transmitter If system disarmed before ensuing entry time runs out CA or Canceled Alarm will be displayed Sounding will stop If system not disarmed before entry time ends EA or Exit Alarm will be displayed and Exit Alarm message will be sent to central station Sounding will continue until system is disarmed or timeout occurs Clear display by entering code OFF a second time Avoid fault when re arming 10 Check wiring connections of expander and receiver to control Check DIP switch settings on the units 41a Check wiring and connections at control and sounder 11b Replace defective siren or bell 12a Check as in 11a and 11b above If battery is discharged or not connected keypad will display BAT fixed word or SYSTEM LO BAT Alpha with no zone number 13a Check as in 11a and 11b above 13b Red jumper on board cut but EOL resistor not connected directly across sounder terminals See Fig 9 1 in Section 9 14 Keypad displays Upload 14 Programming data has been auto matically 14 Key Code plus OFF to clear display Pass Alpha or EC uploaded to central station followin
142. ropriate descriptor for that zone s location will be displayed at the keypad Note Alpha Descriptor entry can be done locally at the Alpha Keypad or remotely using Downloading software The Alpha keypad procedure is described below Entering Zone Descriptors program menu mode 82 The descriptor can be entered when the zone is being defined in field 56 Alternatively zone descriptors can be entered in field 82 The procedure simply requires that you enter the 3 digit reference number for the desired word s The 3 digit number for each word is provided in the Alpha Vocabulary list on a following page Programming the Descriptors 1 With the system powered up enter the programming mode by keying Installer code 8 0 FA147C Installation Instructions Installer Code Program Alpha 0 No 1 Yes 00 Custom Words 0 No 1 Yes 00 Default Descriptor 4 Flashing Cursor system is ready for entry of word Flashing Cursor g ZN 01 BACK ZN 01 BACK t Flashing Cursor if 6 is pressed system is ready for next word ZN01 BACK DIOOR t Flashing Cursor The display at the left will appear 2 Press 82 The Program Alpha prompt will appear 3 Press 1 Yes The Custom Words prompt will appear 4 Press 0 No If a descriptor was not entered previously for zone 1 the default descriptor for zone 1
143. rre ceeeeees 6 1 Transmitter Battery Life ani EIA A een SAS ARSA ARA eed eae 6 2 Receiver SUpervisionscissccieisssctiaes steseshsbecaaetsbecatlsuactai AA EEEE AELA EREA KA RA ERRANA 6 2 Wireless System Installation Advisories ii 6 2 Installation and Setup of the 5881 Series Wireless Receiver 6 2 Installing the 5800TM Module ii 6 2 Programming the Control For Wireless i 6 3 Enrolling 5800 Series Transmitters ii 64 5800 Series Transmitter Input Loops i 6A 5800 Series Transmitter Input Types srrsrrrrnrsrrrrrrrrrrrrrnrrrrr rr ese 6A Compatible 5800 Series Transmitters iii 6 5 iii Table of Contents Continued Section 6 Section 7 Section 8 Section 9 Section 10 Section 11 Section 12 Auxiliary Device Current Draw Worksheet srserrrnrsrrrrrrrrrrrrrnnr rn nr ren 12 2 Wireless RF Zone Expansion 5800 RF Systems Continued Programming the Receiver and Transmitters 5800 RF System 6 6 Enrolling Transmitters into the System i 6 7 Enrolling Through Zone Programming 56 ii 6 7 Check out Procedure for Wireless Zones ii 6 11 Go No Go Test aliante rr Ri e RI 6 11 To Either Temporarily or Permanently Remove a Zone in 56 Mode 6 11 Delet
144. ry The minimum battery size recommended is the No 467 12V 4AH battery See Calculating the Battery Size Needed below The battery is installed in the control cabinet The standby battery connection is automatically checked every 3 minutes CSFM requirement In addition entry into the test mode will cause a battery test to be initiated If there is no battery connected or a low battery a low battery message is displayed and if so programmed will be reported to the central station Calculating the Battery Size Needed Determine the total device current draw after filling in the AUXILIARY DEVICE CURRENT DRAW WORKSHEET on the next page To this figure add the 100mA that is drawn by the control panel itself Then to determine the battery size needed use the formula thet follows 12 1 FA147C Installation Instructions Total Current Drawn x Number of hours standby wanted Battery Ampere Hours Convert mA figure to decimal Amps see example that follows Example If total auxiliary device current drawn is 450mA add 100mA for the control panel for a total of 550 mA 0 55 amps if 24 hour standby is wanted the calculation will be 0 55mA x 24 hours 13 2 Ampere Hour battery needed In this example two 7 Amp Hr batteries connected in parallel must be used Making the Battery Connections 1 Use the battery standby formula shown above to select the appropriate battery for the installation Remember when calculating th
145. s Alarm System While this System is an advanced design security system it does not offer guaranteed protection against burglary fire or other emergency Any alarm system whether commercial or residential is subject to compromise or failure to warn for a variety of reasons For example e Intrusion detectors e g passive infrared detectors smoke detectors and many other sensing devices will not work without power Battery operated devices will not work without batteries with dead batteries or if the batteries are not put in properly Devices powered solely by AC will not work if their AC power supply is cut off for any reason however briefly e Signals sent by wireless transmitters may be blocked or reflected by metal before they reach the alarm receiver Even if the signal path has been recently checked during a weekly test blockage can occur if a metal object is moved into the path e A user may not be able to reach a panic or emergency button quickly enough e While smoke detectors have played a key role in reducing residential fire deaths in the United States they may not activate or provide early warning for a variety of reasons in as many as 35 of all fires according to data published by the Federal Emergency Management Agency Some of the reasons smoke detectors used in conjunction with this System may not work are as follows Smoke detectors may have been improperly installed and positioned Smoke detectors may not sense fires
146. s each time a contact is faulted A test report should be transmitted if programmed to the Central Station immediately If the backup battery is discharged or missing the sounder may not turn on and a Low Battery report will be transmitted with a Test report The keypad will beep once per minute as a reminder that the system is in the Test Mode To turn off the test mode enter security code and press the OFF key Note For 5800 wireless systems triggering a zone set to Arm Away Arm Stay or Disarm will take the system out of the TEST mode and cause that action Alarm messages will be sent to the central station during the following tests Notify them in advance that tests will be in progress Arm the system and fault one or more zones After 15 seconds if optional dialer delay is selected silence alarm sounder s by entering the security code and then pressing OFF Check the Entry Exit delay zones Arm the system AWAY wait a short period and open an entry exit door Check for proper exit delay time and keypad sounds Close the entry exit door when the exit delay tones from the keypad begin to speed up When the keypad indicates that the system is armed AWAY 2 short tones plus the armed AWAY message display wait a few moments then open the entry exit door Check for entry delay sounds from the keypad then disarm the system by entering the security code and then pressing OFF The keypad should display a Ready
147. s rear which will permit it to be mounted horizontally or vertically 2 faced adhesive tape may be used if preferred Wires can be brought out from the side or back a round breakout is also available on the back Affix the Phone Module s connections label supplied separately to the inside of the Phone Module s cover if the cover is used If you have installed the module within the cabinet affix the label to the inside of the control cabinet s door 8 1 FA147C Installation Instructions Phone Module Wiring xh The FA4285 Phone Module is wired between the control panel and the premises handset s It listens for touch tones on the phone line and reports them to the control panel During on premises phone access it powers the premises phones during off premises phone access it seizes the line from the premises phones and any answering machines Note The phone lines must be in service for the phone module to function even when accessing the system from an on premises phone The control should be powered down when making any wiring connections 1 Make 12V and and data in and data out connections from the Phone Module to the control using the connector cable supplied with the Phone Module see Figure 8 1 Color Lead Terminal On Control GREEN DATA IN terminal 6 These are the same connections as those 3 used for remote keypads BLACK AUX terminal 4 RED AUX terminal 5 YE
148. sage is displayed you can proceed to the next step 5 3 FA147C Installation Instructions 3 Fault and restore every contact or sensor in each expansion zone individually to ensure that it is being monitored by the system Each time a zone is faulted the keypad should display the number of the faulted zone as programmed by you just previously in 56 mode When each zone is restored the READY TO ARM message should appear again 4 When you get the proper displays on the keypad s the wired expansion zones in the system are functioning properly xh If a CHECK 09 message appears on the display data from the control is not being received by the zone expander module Check your wiring and the DIP switch settings on the module SECTION 6 Wireless RF Zone Expansion 5800 RF Systems In This Section Wireless systems available Installing the wireless receiver 5881 or 5882 Installing the 5800TM Module Programming for the wireless receiver 5881 or 5882 Setup and installation of the wireless transmitters 5800 series Enrolling 5800 series wireless transmitters Checkout procedure for wireless zones test modes 5882L or 5882H in Canada Wireless Systems Available UL xh The FA147C supports wireless zones which may be used exclusively or in addition to hardwire zones 1 through 6 The following receivers may be used with this system and each supports the number of zones shown
149. se the keypad to beep twice 10 Confirmed A022 4064 Section 14 Sequential Mode for 5800 Transmitters If the serial and loop number combination is already present in the system a single long beep will be heard from the keypad If this happens the system will not display the serial number but will wait for a transmission from another transmitter or transmitter loop input 6 The system will then enter an optional confirmation mode so that the operation of the actual programmed input can be confirmed Activate the loop input or button that corresponds to this zone We recommend that you confirm the programming of every transmitter before proceeding to the next zone When the system sees activity on the appropriate input it will beep three times and display the confirmation message Press or the upper left hand button of the program tool when you are ready to enroll the next transmitter At any time during this step you may press the key on the keypad or the upper left hand button of the program tool if you are satisfied with the serial and loop number combination that has been enrolled regardless of whether or not the enrolled input has been confirmed This will ready the system to enroll the next transmitter If the incorrect transmitter has been enrolled press the key on the keypad or the upper right hand button of the program tool to delete the serial number and return to the LEARN S N prompt
150. stem Status And Restore Report Codes 60 68 70 75 Enter codes as follows 1 9 0 B C D E or F Enter 11 for B 12 for C 13 for D 4 14 for E 15 for F With 4 2 Format Enter codes in both boxes 1st and 2nd digits for 1 9 0 or B F as described above A 0 in the first box will disable the report With Ademco Contact ID Reporting Enter any digit other than 0 in the first box to enable zone to report This is an enabling code only and is disregarded in the actual reporting to the central office Entries in the second boxes will be ignored A 0 in the first box will disable the report Examples For Code 32 Two Digits enter 3 2 For Code B2 Hexadecimal enter 11 2 Press 60 TROUBLE REPORT CODE This will be sent if a zone goes into trouble Press 61 BYPASS REPORT CODE This will be sent when a zone is manually bypassed Press 62 AC LOSS REPORT CODE Timing of this report is random with up to a 48 minute delay The keypad response is about 6 seconds to display the AC failure The restore report has a random delay of up to about 12 minutes If AC restores before the report goes out there is no AC restore report Press 63 LOW BAT REPORT CODE This will be sent when a low battery condition exists in the system s standby battery Note Connection to the standby battery is checked every 3 minutes CSFM requirement Press 64 TE
151. stem is working before connecting field wiring from zones and devices do the following 1 Temporarily connect a 1000 ohm end of line resistor across each of the basic hard wire zones 1 6 as shown in the Summary of Connections diagram Without actual zone wiring or EOL resistors connected the keypads in the system will not display the Ready message Power up the system by plugging the AC transformer previously wired to the control into an unswitched 120VAC outlet Busy Standby Alpha keypads or dI Fixed word keypads will be displayed After approximately 1 minute the green READY LED should light and the word READY Fixed word keypads or DISARMED READY TO ARM Alpha keypads should be displayed To bypass the 1 minute delay press plus 0 If the Ready display does not appear on any of the keypads in the system or a Not Ready message is displayed check the keypad wiring connections and make sure each of the 6 basic hard wired zones has a 1000 ohm resistor connected across its terminals keypad Check the wiring A If an OC or OPEN CIRCUIT is present on the keypad data from the control is not reaching the 4 When you get the proper Ready displays on the keypad s the system is functioning properly at this point Do not remove the EOL resistors until you are ready to make connections to the hard wired zones to allow for testing later in the manual Unplug the A
152. t back an active zone type to re enable it A serial number that has been entered for a 5800 system will not be deleted if the zone is temporarily disabled by answering No to the prompt above If only the physical transmitter is to be removed or changed i e its serial number deleted as when replacing a unit that has a non removable battery it can be done in 56 Mode Deleting a Transmitter Serial Number From a Zone in 56 Mode 6 12 Procedure 1 2 In the programming mode press 5 6 to enter Zone Programming mode Then enter the zone number and press repeatedly until the cursor is under the RF Input Loop L position This is the specific input loop or button on the transmtter that has been entered for that zone Enter a 0 at this point then press A prompt Delete S N will appear Enter Yes to delete the existing serial number from the system Note that the other programmed values for that zone will not be deleted This will allow you to reinstate a new transmitter in its place A display for the next zone number will appear To exit enter 00 Press 99 to exit the programming mode SECTION 7 Relay Outputs and X10 Type Module Usage In This Section Relay Device Basics 4204 and 4229 Relay Module Connections Using an X10 Type Module PF284 Programming Options Defined Programming Output Relays Programming for an X10 Type Module Programming for Chime by Z
153. t as user 0 Section 15 System Communication Entries 6 through 9 will send a report to a pager using the following format AAAAAAAAAAAAAAAA BBB CCCC where A Optional Up to 16 digits for Account numbers PIN numbers or any additional data that will precede the 7 digit system status code BBB and CCCC see B and C below This optional data is programmed in field 93 PAGER CUSTOM DATA B A 3 digit code that describes the event that has occurred in the system see the explanation below C A 4 digit User or Zone number depending on the type of event that has occurred For alarms or troubles these digits represent the zone number For openings disarming and closings arming these digits represent the user number In this system the first 2 digits will always be 00 Single digit zone or user numbers are also preceded by a 0 See the explanation that follows Summary Optional 16 digits AAAAAAAAAAAAAAAA BBB CCCC 4 digit User or Zone Programmed in t field 93 3 Digit Event Code The 3 digit Event codes BBB that can be sent are 911 Alarms The 4 digit number CCCC that follows this code will be the zone number that has caused the alarm 811 Troubles The 4 digit number CCCC that follows this code will be the zone number that has caused the trouble 101 Open system disarmed The 4 digit number CCCC that follows this code will be the User number 102 Close system arm
154. t steps 3 and 4 above to create the desired word s Note that the 4 key can be used to move the cursor to the left if necessary Remember no word or word string can exceed 10 characters 6 Press the 8 key to save the custom word s and return to the CUSTOM WORD display 7 Repeat steps 2 5 for other custom words to be entered To change a custom word just overwrite it 8 Ifno more are to be entered press 0 No at the CUSTOM WORD prompt to return to the Descriptor entry The custom word s will be automatically added to the built in vocabulary 9 Exit the programming mode by keying 99 When zone descriptors are being entered as described in step 6 of Programming the Descriptors the custom word numbers are 245 to 254 for words 1 to 10 respectively 000 001 002 004 005 006 007 009 010 012 026 051 052 053 054 055 Note ALPHA VOCABULARY LIST For Entering Zone Descriptors Word Space A AIR ALARM ALLEY AMBUSH AREA APARTMENT ATTIC AUDIO B BABY BACK BAR BASEMENT BATHROOM BED BEDROOM BELL BLOWER BOILER BOTTOM BREAK BUILDING C CABINET CALL CAMERA CAR CASH CCTV CEILING CELLAR CENTRAL CIRCUIT CLOSED COMPUTER CONTACT D DAUGHTERS DELAYED DEN DESK DETECTOR DINING DISCRIMINATOR DISPLAY 057 059 060 061 062 064 065 066 067 068 069 071 072 073 095 104 105 DOOR DOWN DOWNSTAIRS DRAWER DRIVEWAY DUCT E
155. te Back Cover Note A Programming Guide is supplied in addition to this manual Figure 2 1 Figure 2 2 Figure 2 3 Figure 2 4 Figure 3 1 Figure 3 2 Figure 4 1 Figure 5 1 Figure 6 1 Figure 7 1 Figure 7 2 Figure 7 3 Figure 8 1 Figure 9 1 Figure 9 2 Figure 10 1 Figure 10 2 Appendix B List Of Figures Installing the Cabinet Lock inbie cienie eii nE e ERE R r fue tr kr 2 1 Installing The PC Board Alone or if used With a 4204 4219 or 4229 2 2 Installing the PC Board amp RF Receiver if used Together in the Cabinet 2 3 Standard Telephone Line Connections i 24 Keypad Connections to the Control Board coseececeeeeeeesseeeeensaes 3 2 Using a Supplementary Power Supply for Keypads ceesneeeeeees 3 3 4 Wire Smoke Detector Connections sssssesssresrsrrsssresrsrr seeceseceeeeeaeesaeceaecneeennee serte 4 2 Wiring Connections 4219 and 4229 ii 5 1 5881 and 5882 Wireless Receivers cover removed seseeeeeeeses 6 3 4204 Connections To Control sssssssssserssrerrrsrerrrrrr e 7 2 4229 Connections To Control ccsseceseeseeeseeeeeecaaecsaecne as ra Teta aeaa 7 2 Connecting an X10 Type Module PF284 ii 7 3 FA4285 Phone Module Wiring Connections iii 8 3 Bounder WIN Tedi ord peia race FA NER AR arn ed ote is 9 2 Using
156. that start where smoke cannot reach the detectors such as in chimneys in walls or roofs or on the other side of closed doors Smoke detectors also may not sense a fire on another level of a residence or building A second floor detector for example may not sense a first floor or basement fire Finally smoke detectors have sensing limitations No smoke detector can sense every kind of fire every time In general detectors may not always warn about fires caused by carelessness and safety hazards like smoking in bed violent explosions escaping gas improper storage of flammable materials overloaded electrical circuits children playing with matches or arson Depending on the nature of the fire and or location of the smoke detectors the detector even if it operates as anticipated may not provide sufficient warning to allow all occupants to escape in time to prevent injury or death e Passive Infrared Motion Detectors can only detect intrusion within the designed ranges as diagrammed in their installation manual Passive Infrared Detectors do not provide volumetric area protection They do create multiple beams of protection and intrusion can only be detected in unobstructed areas covered by those beams They cannot detect motion or intrusion that takes place behind walls ceilings floors closed doors glass partitions glass doors or windows Mechanical tampering masking painting or spraying of any material on the mirrors windows or any part
157. the system If you plan to use an existing transmitter it must first be enrolled into the system as its associated zones You may then program it as the tool Batteries can remain in the transmitters after the transmitters have been enrolled into the system However to prevent possible problems make sure these transmitters are not faulted while other transmitters are being enrolled Wireless motion detectors should be covered or placed face down to prevent transmissions Enrolling Through Zone Programming 56 1 Enter Programming mode Installer Code 8 0 Enter Zone Programming by pressing 56 If the system has been set up to use 5800 series RF and a program tool has been entered skip to step 4 If no program tool has been entered the following prompt will appear 2 Ifa program tool is being used enter 1 If not using a tool enter 0 and skip to Step 4 Program Tool 0 No 1 Yes 00 Input S N 3 If l is entered the system will prompt for the unit s DPL 2 serial number Enter the program tool s serial number AXXX XXXX using one of the following methods a Enter the 7 digit serial number for the transmitter or b Press any button on the transmitter The keypad should beep twice and display the serial number of the tool 00 Input S N In this example the serial number is A123 4567 Once pu 5 enrolled the upper left hand button of the program tool can A123 4567 be pressed to ready the system for enrolling
158. the Cabinet Installing the Lock Installing the Control s Circuit Board Alone or if used with a 4204 4219 or 4229 Module Installing the Control and RF Receiver Circuit Boards Together in the Cabinet Standard Phone Line Connections Wiring The AC Transformer Installing The Back Up Battery Earth Ground Connections Mounting the Cabinet Mount the control cabinet to a sturdy wall using fasteners or anchors not supplied in a clean dry area which is not readily accessible to the general public Four mounting holes are provided at the back of the cabinet If an RF Receiver is being used and you intend to mount its PC board within the cabinet note the following e Do not mount the cabinet on or near metal objects This will decrease RF range and or block RF transmissions from wireless transmitters e Do not locate the cabinet in an area of high RF interference revealed by frequent or pro longed lighting of the LED in the receiver after it is operational Random flicker is OK Installing the Lock if used Use an Ademco No N6277 Cam Lock and No N6277 1 Push On Clip Retainer Clip Note The cabinet can be closed and secured without a lock by using 2 screws in the cover s edge RETAINER CLIP 1 Remove the cabinet door It is easily NOTE POSITION removable for servicing and is easily re installed 2 Remove the lock knockout from the control cabinet door Insert the key into the lock RE
159. the following via the keypad on the phone INSTALLER Code 4111 then press key 1 OFF A beep should be heard on the phone and from a wired keypad and the words DISARMED READY TO ARM or DISARMED NOT READY TO ARM should be heard indicating that the command was entered successfully DISARMED NOT READY TO ARM would indicate an open zone Hang up the phone To Check Phone Module Operation From an Off Premises Phone 1 Have someone dial the premises phone number using a Touch tone phone e Ifthe phone system does not include an answering machine 2 long tones will be heard in the caller s phone followed by a voice prompt HELLO ENTER PHONE CODE NOW The caller should then enter the programmed 2 digit phone code entered in field 26 VOICE MODULE ACCESS CODE e Ifthe premises phone system includes an answering machine the 2 digit phone code should be entered during a pause at the beginning of or during the outgoing answering machine message Note If 15 was entered in field 95 to bypass an answering machine and an FA4285 Phone Module is included in the installation off premises phone operation will be affected Read the Important Note in the programming information for field 95 on the previous page When the 2 digit phone code is entered the caller will hear a voice prompt asking for entry of the 4 digit system code ENTER SYSTEM CODE NOW The caller should then enter the INSTALLER code
160. to a pager See field 47 SPLIT DUAL REPORTING Enter 0 9 11 for 12 for 13 for a pause 2 secs If fewer than 16 digits are entered exit by pressing and then 94 if entering next field To clear entries from field press 93x FA147C Installation Instructions Press 94 DOWNLOAD PHONE NUMBER Enter up to 16 digits 0 9 11 for 12 for 13 for a pause Do not fill unused spaces End field by entering If fewer than 16 digits entered exit field by pressing and next field number To clear entries press 94 Press 95 RING DETECTION COUNT FOR DOWNLOADING Refer to the chart below and program this field accordingly Phone Answering Module Machine Downloading Field 95 Programming Set for value other than 0 1 14 This will enable the control panel to answer the phone call Otherwise it will not be possible to access the Module Set for a value higher than the number of rings for which the answering machine is set Example if machine is set for 4 rings use value 5 or higher This is recommended so that the Phone Module can still be accessed if the answering machine is turned off and does not answer the phone call Set for value other than 0 1 14 15 to bypass answering machine See Important Note below Enter 0 Enter 1 14 Enter 15 Important Note If 15 is entered in field 95 to bypass an answering machi
161. to the system as you are entering the zone information in field 56 the procedure will be found in the Wireless RF Zone Expansion section or you can enroll all the transmitters in 83 menu mode after all other zone information has been entered in field 56 The enrolling method in 83 is called sequential enrolling and is described in this section As an option the new sequential mode allows you to use a 5804 button type transmitter as a program tool The advantage of using a program tool is that it enables remote enrollment You can move to the physical location of the transmitter to be enrolled press the upper left hand button of the program tool and then trip the intended transmitter see step 10 for operation The transmitter that you use as the program tool can also be used as a transmitter in the system If you plan to use an existing transmitter it must first be enrolled into the system as its associated zones You may then program it as the tool An alpha keypad is required for the following procedures To enroll transmitters sequentially after all other zone information has been programmed do the following 1 Enter Programming mode Installer Code 8 0 on an Alpha keypad Enter the Serial Number Sequential mode by pressing 83 The following prompt will be displayed 2 Ifusing a program tool enter 1 Ifnot using a tool enter 0 If a tool has already been programmed this prompt will 0 No 1 Yes not appear I
162. tries Press 45 PHONE SYSTEM SELECT default 1 If Central Station Receiver is not on WATS line 0 Pulse Dial 1 Tone Dial If Central Station Receiver is on WATS line 2 Pulse Dial 3 Tone Dial Press 46 REPORT FORMAT PRIMARY SECONDARY Determines which format is to be used to report to the central station Default 7 2 4 2 ADEMCO Lo Speed Standard 8 4 2 Radionics Standard 6 or undefined 4 2 ADEMCO Express 7 ADEMCO Contact ID Reporting Note The maximum number of alarm and alarm restore reports during one armed period is determined by field 92 Press 47 SPLIT DUAL REPORTING 0 disable Backup report only Entries 1 through 9 can be made as indicated in the table below Entries 6 through 9 will send a report to a pager in addition to the selected primary phone number but you must enter the pager number as the secondary phone number in field 42 All reports except Open Close Open Close for users 5 25 Can only be used if the Primary reporting format is Ademco Contact ID and a primary phone number is programmed If reporting to a Pager choose from 6 7 8 or 9 as desired 1 2 3 4 5 ea 1 2 3 4 5 6 8 Ez Will report only Users 5 6 7 amp 8 If using 5800 series wireless button type devices the zone number of the arm or disarm button 10 25 will be sent as the user number Note If Quick Arm is used Close will repor
163. ult 5 Press 30 Alarm Bell Timeout Enter 0 for no timeout 1 for 4 min default 2 for 8 min 8 for 12 min 4 for 16 min 6 Press 51 Confirmation of Arming Ding Enter 0 for no default 1 for yes 2 for yes but with RF arming only 7 Exit the programming mode by entering 99 Testing the Sounder After installation of the sounder is completed the Security System should be carefully tested as follows 1 Make sure that the back up battery is properly connected 2 Enter the INSTALLER code and press the TEST key on the wired keypad The external sounder should sound for 1 second if the sounder is good and proper connections have been made Note that if the backup battery is discharged or missing the sounder will not turn on To turn off the test mode enter the INSTALLER code and press the OFF key Disconnect the wires from the battery terminals Using the Memory of Alarm Trigger for a Strobe A strobe can be connected to the Memory of Alarm voltage trigger as shown below The Memory of Alarm trigger will apply a ground when any alarm occurs that will trigger the external sounder and remains in this condition until the Memory of Alarm is cleared at the control The strobe will remain active so long as the memory of an alarm exists VOLTAGE TRIGGER PIN 2 MEMORY 3 PIN CONNECTOR OF ALARM SUPPLIED OPTIONAL STROBE THIS TRIGGER CAN ALSO BE USED FOR CELLULAR LONG TO TERMINAL 5 12V RAN
164. units etc connected to a single 4 wire run determine the current drawn by all units connected to the single wire run then refer to the Wiring Run chart to determine the maximum wire length that can be safely used for each wire size Current draw for all devices can be found in the Specifications and Accessories section Note Refer to Auxiliary Device Current Draw Worksheet in the Final Power Up section for current draw for all keypads Maximum wire lengths for any device that is homerun to the control can also be determined from the chart based on the current draw of that device alone Make sure the control is not powered up while making the following connections Run field wiring from the control to the keypads using standard 4 conductor twisted wire cable using the wire gauge determined in step 1 Connect remote Keypads to terminals 4 5 6 and 7 on the control board 3 1 FA147C Installation Instructions oh Wiring Run Chart For Devices Drawing Aux Power From The Control 12V amp 12V ai TOTAL CURRENT DRAWN BY ALL DEVICES CONNECTED TO A SINGLE WIRE RUN 50mA or less 100mA 300mA 500mA 500 ft 152m 250 ft 76m 80 ft 24m 50 ft 15m 750 ft 228 6m 380 ft 116m 130 ft 39 6m 80 ft 24m 1300 ft 396m 650 ft 198m 220 ft 67m 130 ft 39 6m 1500 ft 457m 1000 ft 305m 330 ft 100 5m 200 ft 70m Includes Keypads RF Receivers Expansion Relay Units or the FA4285 Phone M
165. y Check Out Procedure iii 3 3 Basic Hard Wired Zones 1 6 mummsmsesrsrsrsrsrsrsrsrrer rerrrsersrsrsrrrr reser rr renen er ber sr senere nerna 4 1 Installing the Hard Wired Zones ii 4 1 Common Characteristics For Zones 1 6 ceeeeecseeeeenaeceeeaeeceeeeees 4 1 Wiring Burglary and Panic Devices to Zones 1 6 i 4 1 Wiring 4 Wire Smoke Combustion Detectors i 4 1 Compatible 4 Wire Smoke Combustion Detectors sne 4 2 Programming Hard Wired Zones ii 4 2 Programming Panic Keys aaa ao rare 44 Check Out Procedure for Hard Wired Zones i 4 5 Wired Zone Expansion 4219 4229 msesssessrsrssrsrerreresrrrer seseseeecssesseeseeeeeesesseese seese 5 1 General Informationi uniranno 80 seis 5 1 Installing Zone Expansion Units i 5 1 Connections and Set Up se sssostervesestesssiosesigsnats ngsesssessbessrisdoesnsnesneNeereins ter sisstbessedes 5 1 Programming Wired Expansion Zones i 5 2 Check Out Procedure for Wired Expansion Zones ccccccccsssssseceseee caseeeseeeeceseeeeees 5 3 Wireless RF Zone Expansion 5800 RF SystemS 000000000 6 1 Wireless Systems Available caeeecesaececsssaececssaeeecna seeeesesaesecssaeeeensaes 6 1 Wireless System Operation and Transmitter Supervision s sssssssssressrssrsrers
166. zones 10 11 12 110 11 17 2 etc 7 9 FA147C Installation Instructions Programming For Chime By Zone If you want CHIME when on to sound when any entry exit or perimeter zone is faulted you need only enter a 0 in field 31 In this case no further programming is required If you want CHIME when on to sound only when specific zones are faulted a 1 must be entered in field 31 Chime by Zone requires that you enter the specific zones which have been selected for chime in Zone List 3 using 81 programming mode The programming procedure for chime only on specific zones is provided below 1 A 1 must be entered in field 31 2 Press 81 Zone List Displays Upon keying 81 the screen on the left will appear Enter Zone List Number 03 Press the key to advance Zone List No 00 Quit 03 Zone List number 03 3 0 Enter Zn N The screen on the left will appear showing zone list 3 selected nter n Num Now enter each zone number to add to the zone list by first entering the zone 00 Quit 01 number then pressing the key example 01 02 03 Zone number s After all zones for chime are entered key 00 This will advance you to the next screen If you wish to delete the

Download Pdf Manuals

image

Related Search

Related Contents

HUMEX MAL DE GORGE, collutoire,  Benjamin Janutta - opera  Trident Precast Concrete Deck Truck Scale  Bedienungsanleitung  Rollei Sportsline 60  PRESTIGE II 308/450  MAINBOARD User`s Manual  Remington S-2004 User's Manual  MAB 455 Original- Betriebsanleitung  Microlife BP A80 blood pressure unit  

Copyright © All rights reserved.
DMCA: DMCA_mwitty#outlook.com.