EluneVision Reference Tension
Contents
1. wall mounting oD gt e oD ac aD Dm E aD B l Adjust the screw counter clockwise to loosen the mounting plate see figure A Adjust the screw clockwise to fasten it see figure B Control System Switch Control 1 Insert switch cord into the appropriate interface of the right end of the screen casing 2 Push the button to the down position to extend the screen Push the button up to retract the screen To stop the screen return the button to the middle position RF Remote Control 868 MHZ 1 The remote has been set up at the factory and should work right away However if you would like to control another screen with the same control you will need to use the learn function 2 Make sure the control switch is in the neutral position and the switch cable is disconnected from the screen Please press the learning hole at the right end cap for 3 seconds indicated by a red LED flash Then press the back of the remote control if successful the red flash from the screen will stop flashing and be on Please refer to remote control user manual for detailed instructions 3 Please operate as follows Press to lift the screen laser pointer Press to stop the screen button Press toextendthescreen Remote control battery AAA DC 1 5Vx2 DC 3 12V Cordless Trigger Control Optional2. ELUNEVIS USER S MANUAL FOR TENSIONED SCREEN To The Owner Thank you for purchasing our Tab Tension screens using our excellent screen materials and mechanical components to give you years of trouble free enjoyment Please take a moment to read the user manual before installation to avoid any potential issues A Safe Guide 1 When assembling do not stand right under the screen Expansive bolts should be firmly punched and fixed into the wall or ceiling 2 Be sure the ground wire is connected with power cable to avoid electric shock 3 When using the laser pointer on the remote control please not point it directly into people s eyes to avoid injury 4 Keep screen fabric away from the high temperatures to avoid permanent material deformation Assembling 1 Please open the carton and check accessories according to the list Before installing screen please screw off the connection plate between casing and bottom bar Figure 1 2 Adjust the position between the two mounting plates Figure 2 Note Please keep the screen case horizontal when assembling Suggested Assembling Methods Plastic wall anchor Mounting holes Ceiling mount Plastic wall ancho Z Mounting holes
3. Limit Switch Control The Limit Switch Controls of the screen adjust how far the screen goes down extends and The trigger has been set up at the factory and should work right away Please operate as follows a l g9 p y 9 y 3 up retracts The Down Limit Switch controls the extension and the Up switch controls the retraction 1 Make sure the control switch is in the neutral position The controls are set at their default positions in the factory To adjust the limit switches please use the 2 Insert the trigger directly into trigger out interface of the projector When adjusting tools that s included with your screen you power on the projector the screen should extend automatically When you power off the projector the screen will retract automatically 1 Adjusting for the up limit position how far the screen retracts When the screen retracts and you want to change the position of where the bottom bar stops use the adjusting tool to turn the switch in the direction to make the screen drop more and turn it in the direction and the screen will rise more into the casing Be careful with up limit switch has as too many turns in the direction will send the bar into the casing of the screen If you need to control another screen with the same trigger or changed new remote control than the trigger needs to be mated to the screen again 1 Make sure the control switch is in the neutral position Also make sure your p
4. N KN PERRO BR 4 ORR ROARS IT RK RR KL REAR ae RRR RRR PROG PRB RK LR KKK RRR RRR RRS x ESN Ss m i d t S it ti f A A A If the tension is slack or over tensioned please follow Figure 9 loosen a insert I tighten C tool J Figure 9 Trouble Shooting Fault Reason Resolution Remote control malfunction Check for drained battery Replace Battery Abnormal noise from motor Broken Capacitor Contact Dealer Motor not running Broken Motor Contact Dealer al Refer to Limit Control Screen not retracting fully Limit Switches Secionof manual Ifthere are other malfunctions please consult your dealer Remark 1 Please do not run the screen continuously for more than 5 minutes to avoid motor damage from overheating Please let motor cool down if running continuously for more than 5 minutes 2 Do not scratch up or fold up the fabric 3 After usage please check again there are no foreign objects on the screen surface and then retract the screen into the case 4 Please note small changes to net picture area due to temperature changes are normal Screen Care We encourage you to keep your screen clean Avoid getting any foreign material on it as cleaning may prove to be very difficult or even impossible scratch paint ink etc With reasonable care you may expect years of trouble free use of your screen Area Dusty Dirty Gach Light dustin
5. g is possible Clean with a mild soap solution and dry with 3 with a feather duster a lint free cloth Take care not to scratch the casing Surface Clean with a feather duster Use a lint brush to remove any dirt Accessories Name Picture Quantity Expansive bolt 4 Assembling plate 2 Adjusting tool Hex key Screen learn needle Remote control Manual switch Power cord Plug changed according to different standard EluneVision A Division of Edith Min International Inc Tel 1 905 296 6819 Fax 1 905 627 9567 Web www EluneVision com 2m optional 5m standard
6. rojector trigger function is enabled Press the small hole at the right end cap for 3 seconds with screen learn needle The LED in the screen casing will flash and continue to flash Then please press the hole in 2 Adjusting for the bottom limit position how far the screen extends When the screen extends and the back of the cordless trigger for 3 seconds the LED light in the screen casing should become you want to change the position of where the bottom bar stops use the adjusting tool to turn the switch constantly on if the mating is successful Please refer to cordless trigger control user manual for in the direction to make the screen extend further Turning the switch in the direction will retract details the screen After finishing the learning function insert the wireless trigger into the trigger out interface Our patented cordless trigger allows your screen synchronize its extension and retraction to your bottom limited projector s power cycle When projector is powered on the screen will automatically come down adjusting When projector is powered off the screen will automatically retract B A adjusting tool front side TIN e E Z LLKR RY aS RRR ORY ERROR RRR I OL o OLY Ke eee RIO x RSCG LK PRK BRK PRR RR RRR RR IRRI RRR RRI R OLRM LN VY RONG BERR ORR LK ALLL RR PORK KK AF BRE
Download Pdf Manuals
Related Search