sjm gas booster sjm–810g sjm–830g sjm–850g shin
Contents
1. WORK TEMP GAS BOOSTER AN TEMP SETTING 1 DIGITAL THERMOMETER 2 WORK LAMP 3 TEMP LAMP 4 BURNING LAMP 5 ERROR LAMP 6 LOW WATER LEVEL LAMP BURNING ERROR OVER HEATED LOW POWER WATER LEVEL SHIN JIN MASTER CO LTD R RESTART Display temperature of water inside booster Comes on when displaying the temperature of heated water Comes on when selecting water temperature Comes on while the burner is being operated Comes on in case of any trouble while the washer is running Comes on when the water level inside the booster is lower than the low water level sensor in case of water suspension or shortage 7 POWER LAMP Remain on while the power switch is on 8 TEMPERATURE CONTROL SWITCH Pressing this switch once will increase the water temperature by 1 keeping pressing it will increase the water temperature continuously Pressing this switch once will decrease the water temperature by 1 keeping pressing it will increase the water temperature continuously 9 RESET SWITCH In case of any trouble fix the trouble and press the RESET switch to continue the washing process 10 POWER SWITCH Turns power ON OFF 1 You must set up the booster where the air circulation is good and the exhaust gas can easily be let out of your building 2 Set this product horizontal to the ground 3 As for gas piping have a licensed gas office2. 85 The washer runs automatically according to the selected temperature 6 If you want to stop running simply turn the power switch off and shut off the mid gas valve Make sure the exhaust gas is released outside your building and constantly let air in the room the machine is in For this is an electronic product do not clean it with water DISPLAY PROBLEM GUIDE El Overheat prevention Check for a breakdown of the sensor E4 device under operation Eliminate the cause of overheating and press the Error amp Over Heated continue switch lamps comes on E2 Water thermometer Check for a short circuit in the thermometer short circuit Check for a terminal break away Error lamp comes on E3 Low water level sensor Check the water supply status has detected a trouble Check the normality of the sensor Trouble Low water Check for alien substances around the surface of level lamp come on the low water level sensor and remove any alien substance if present E5 When a gas without flame Check the combustion status is detected Check for a gas leak A flow in flame sensor Check the stability of the flame sensor Error lamp comes on Check for any alien substance around the external surface of the sensor Check for any damages or terminal break down Check the operating status of the gas valve E6 Initial no ignition Check the gas supply status and gas drum Error lamp comes on Check the operating status of high pre
3. SJM GAS BOOSTER USER S MANUAL SJM 810G SJM 8 amp 30G SJM 850G CONTENTS NOMENCLATURES amp FUNCTIONS SPECIFICATIONS CONTROL PANEL INSTALLATION INSTRUCTIONS PROBLEM GUIDE arn nb Ww WY Please make sure to read this manual before usage and keep it handy for necessary information MANUFACTURER SPECIALIZED IN DISH WASHING MACHINE SHIN JIN MASTER CO LTD SMOKESTACK COVER OVERFLOW FLOAT VALVE OVERHEAT PREVENTION SWITCH FRAME WINDOW BURNER FACE GAS VALVE HORIZONTALITY ADJUSTMENT NUT ITEM NAME GAS BOOSTER MODEL NAME 810G 830G 850G DIMENSIONS 300 x 570 x 675 410 x 570 x 675 530 x 590 x 675 W x D x H m m WEIGHT 25Kg 28Kg 36Kg POWER SOURCE 240V 50Hz IGNITION TYPE Continuous Discharge Auto lanition Type GAS CONSUMPTION LNG 16 000 Kcal H LNG 24 400 Kcal H LNG 37 000 Kcal H LPG 1 33 Kg H LPG 2 03 Kg H LPG 3 0 Kg H ELECTRICITY CONSUMPTION 28 W TANK CAPABILITY 30 L 45 L 48 L OF HEATED WATER AVAILABLE 12 L AVAILABLE 18 L AVAILABLE 20 L EXHAUSTION TYPE NATURAL EXHAUSTION WATER PRESSURE USED ATMOSPHERIC PRESSURE USAGE FOR COMMERCIAL DISH WASHER PIPING WATER SUPPLY 15A 1 2 15A 1 2 15A 1 2 HEATED WATER 20A 3 4 25A 1 25A 1 OUTLET GAS SUPPLY 15A 1 2 15A 1 2 15A 1 2 SAFETY DEVICE OVERHEAT PREVENTION LOW WATER LEVEL FLAME DETECTING SELF DIAGNOSIS
4. er Any breakdown due to a natural disaster SJM CHINA CO LTD China Office Room 202 Mei Lian Building 569 Yu Yao Road Jing An District Shanghai P R China TEL 86 21 62320103 06 FAX 86 21 62320102
5. or gas piping office do it for you 4 Make sure to build an exhaust duct to let the exhaust out of your building If you are using an exhaust hood instead of a duct make sure the gas is blown out through the hood 5 Use PF1 2 15A s for water supply piping 6 Use PF3 4 20A s warm water exit Make it as short as possible to minimize heat loss 7 This product may accidentally cause an overflow Make sure to place it where drainage is possible Drains to the floor 8 Clean the inside of gas booster regularly 9 Make sure to place where no flammable material is present Also do not place anything on top of the machine 10 Good air circulation is needed near the bottom of the gas booster to provide enough air for combustion Do not block with any object BEFORE USAGE 1 Make sure you are using the correct gas When delivered the gas product has a sticker indicating the proper Gas to be used on the bottom right corner Check before usage 2 Make sure there is no gas leak Conduct a foam water test 3 Make sure you have the correct power The product is designed to use 240V 50Hz only 4 Make sure you have built an exhaust duct or hood to let the gas out of your building USAGE INSTRUCTIONS 1 Plug the power to an electric outlet 2 Open up the mid gas valve 3 Open up water supply valve 4 Press the power switch 5 Select a temperature When first delivered the temperature is set at
6. ssure transformer Check the operating status of gas valve E7 Loss of flame during Check the gas supply status and gas drum operation Check the stability of flame sensor Error lamp comes on OTHERS 1 Can t adjust If up down switch don t let you change the Temperature temperature check the sensor and joints But the temperature does not go up any higher than 92 so keep that in mind OTHERS 2 Can t continue Running Check the status of display lamps Press the Reset switch while any lamp other than the Error lamp is on If the Error lamp turns off and the machine continues to run it is normal otherwise replace the controller OTHERS 3 Trouble in water supply Remove any alien substance if present Valve If water is filled inside the water supply valve Disassemble it and drain the water 1 In case a trouble occurs during usage of our gas booster check it according to the Problem Guide If this does not help contact our dealers or us for an A S 2 In order to achieve the best after sale quality for warranted repairs the repair it self as well as the parts requisite will be free of charge whereas for onerous repairs the actual technical expenses amp prime costs will be charged Warranted Repair Any breakdown that occurs within 12months after purchase Any breakdown that occurs under standard usage Onerous Repair After the first 12months Any breakdown occurred due to the carelessness of the us
Download Pdf Manuals
Related Search