L6150--ASP User manual Booklet.pmd
Contents
1. 4 NN Masi i Brush Driwe End Cap _ Sprocket Agitator 2 Replace agitator assembly back into the elec tric brush 3 Reinstall agitator cover by lining up the front tabs and slots and rotating downward until the latches snap into place Agitator Cover 4 Line up front of cover and base Rest cover on front edge of base as shown 5 Tilt cover to back Press cover firmly until side and rear tabs snap into place Turn the electric brush upside down and replace the 2 cover screws Electric Shock or Personal Injury Hazard Disconnect electrical supply before servicing or cleaning the unit Failure to do so could result in electrical shock or personal injury from cleaner suddenly starting To Check Agitator Assembly When brushes are worn to the level of the base sup port bars replace the agitator assembly AGITATOR SERVICING Replace Support Bars 1 Remove the electric brush cover agitator cover belt and agitator assembly See To Remove Belt in BELT CHANGING AND AGITATOR CLEANING 2 Remove end caps washers screws end brush and sprocket pieces from ends of old agitator assembly 3 Reassemble agitator assembly To line up screw holes in dowel sprocket and end brush be sure all of the brush sprocket pieces align properly See AGITATOR ASSEMBLY 4 Reinstall belt agitator assembly agitator cover and electric brush cover See To Replace Belt in BELT CHANGING AND AGITATOR C2. CENTRAL VACUUM ACCESSORIES ASP1 amp ASP2 Defender ElectroKit USER GUIDE IMPORTANT SAFETY INSTRUCTIONS Please read all instructions before using the Electric Powerhead When using this electrical appliance basic precautions should always be followed including the following WARNING Electric shock could occur if used outdoors or on wet surfaces 1 Unplug and disconnect power before servicing 2 Always turn off this appliance before connecting or disconnecting either hose or motorized nozzle 3 Do not vacuum up anything that is burning or smoking such as cigarettes matches or hot ashes 4 Do not pick up flammable or combus tible liquids such as gasoline or use it in areas where they may be present 5 Use only as described in this manual Use only manufacturers recommended at tachments 6 Do not unplug by pulling on cord To unplug grasp plug not the cord 7 Do not handle system or appliances with wet hands 8 Turn off all controls before uplugging 9 Do not use with damaged cord or plug 9 Do not allow to be used as a toy Pay close attention when used by or near small children 10 The hose contains electrical wires Do not use if damaged cut or punctured Avoid picking up sharp objects 11 Do not put any object into openings 12 Do not use with any opening blocked keep free of dust lint hair and anything that may reduce air flow 13 Keep hair loose clothing
3. fingers and all parts of the body away from openings and moving parts 14 Do not leave vacuum or brush when plugged in Unplug from outlet when not in use and before servicing 15 If appliance is not working as 1t should has been dropped damaged left outdoors or dropped into water return it to your distributor 16 Use extra care when cleaning on stairs SAVE THESE INSTRUCTIONS INTENDED FOR HOUSEHOLD USE ONLY 1 UA U OO NA 0 ASP1 amp ASP2 DustMate Defender ElectroKit Individual tools may vary and are subject to change at any time Tool Kit Includes Accessories SFH 630 Slimfit Style 4 Wire Swivel Electric Crush Proof Hose EB 250AT 14 Defender Electric Power Brush BW 240 Lower Wand W 535 Top Wand W 419H Chrome Telescopic Ratchet Wand H 431 Plastic Hose Hanger ASP1 Direct Plug In ASP2 6ft Pigtail Cord CT3BL Clip On Tool Caddy 2000 S 1600 S 1200 P 350P P 325 P 225 P 215 CB 180 Mesh Tool Caddy Bag Models are SL 2940 SL 2340 SR 89 SR 88 SR 50 2 Cleaning Attachments amp Tools 9 FB 215BLK 12 Floor Tool 10 CT 630BLK Premium Crevice Tool 11 DB 630BLK Premium Dusting Brush 12 UT 630BBLK Premium Upholstery Tool with Brush The following Central Vacuum units when used in con junction with the listed electric floor brushes have been tested and approved by the Carpet and Rug Insti tute for use on carpet The list of approved Va
4. LEANING AGITATOR ASSEMBLY S cs End Electric Brush kalk Fii Brush End Cap End Cap Screw Agitator Unit Washer 7 Brush Sprocket EB250AT Electric Brush Numbers with applies only to Dirt Sensor parts Diacram Stock DESCRIPTION 8 B27008 SCREW 9 EB27009 MOTOR GASKET 10 EB29010 BELT T EB2401 1 MOTOR SPRING y EB29012 LOWER PLATE 3 EB29013 MOTOR 14 EB24014 MOTOR BRIDGE 15 EB29015 OVERLOAD PROTECTOR l EB21016 LIGHT BULB Y EB29017 BULB SOCKET 18 B24018 HANDLE RELEASE PEDAL 19 EB24019 SWIVEL 19 EB30019 SWIVEL 2 EB27021 WIRE CONNECTOR n EB24022 SWIVEL SEAL 2B EB29023 WHEEL M EB24024 PEDAL EASY RELEASE M EB30024 PEDAL EASY RELEASE 25 EB24025 REAR COVER 25 EB30025 REAR COVER 26 EB24026 FRONT AXLE ASSEMBLY 2 EB29027 AGITATOR UNIT 28 EB27028 INDICATOR WINDOW 29 EB29029 LIGHT LENS 30 EB27030 EXHAUST FOAM 31 EB29031 WINDOW REFLECTOR 32 EB24032 CORD amp PLUG ASSEMBLY jenem s ka WE d 32 EB30032 LEAD WIRE UNIT AN fargo Ni 3 EB29033 REFLECTOR NOZZLE 4 k a ES BH M EB29034 NOZZLE HOUSING DECO 54 42 34 EB31034 NOZZLE HOUSING DECO a 36 35 EB27035 SWIVEL CAP Reena NM T EB27036 CAM INDICATOR if is 3 EB30037 FRONT COVER 50 si ar53 cA A AG 38 B30038 PCB B UNIT eben DANN ME 39 EB30039 SCREW 40 EB3I040 PCB DIRT SENSOR na 1s EN 1 A 4l EB29041 LEAD WIRE a a RW 1 Un 42 EB24042 INDICATOR LEVER A ar A MA 43 EB24043 PAD FOOT PEDAL 8 AA Ji y A
5. cu Maid Silent Partner models are S 3240 S 3200 S 2600 S P 125P and P 110 The list of approved Astro Vac SR 40 SR 40V and SR 36 The approved electric floor brushes are EB 180 Super Groom EB 210 Super Groom IT EB 240 Vacu Maid and the EB 260 Vacu Maid which have been approved for use on carpeting when used in conjunction with the aforementioned Vacu Maid Silent Partner and Astro Vac central vacuum units EB 250AT N 14 Electric Brush C Release Pedal Mot Shewn E Use this powerbrush to vacuum wall BU P to wall carpeting handmade carpets RN x A ky d lt fine rugs and other flooring AL i i Headlight and Lens Pile Height Indicator Protector Overload eal Reset Button AI 9 or Y i JAE 4 Le ou oe Edge Cleaner A Hot Shown VAY HodelSerial Humber ll y n Bottom b This powerbrush must be used mw ORGE with the top and lower wands A Features include e Quietdrive V Belt Multi grooved reinforced belt for continuous contact and efficient transfer of power to the brush e Quick Wand Release for an easy switch from carpet to hard floor edge cleaning or above floor cleaning 4 level height adjustment adjusts to match surface being cleaned Soft Bumper wraps around brush to protect baseboards and furniture Slim line profile for ease of cleaning under furniture e Headlight for lighting your cleaning path
6. e Active Brush Edge Cleaner guide either side of the brush along baseboards or next to furniture to help remove dirt trapped at carpet edges REMEMBER As with all electric appliances risk of shock 1s possible Do not remove brush pull wands out or attempt maintenance while power is on E i The swivel located on the powerbrush allows you to turn the handle to the left side to i Telescoping Wand The wand length is LIE amp 44 adjustable and requires no N qt assembly To adjust En v reach further under low furniture Wand e simply push down on the ma amp Wand adjust button and When raising the wand you may slide the upper wand to the desired height have to hold the powerbrush With your hand or foot Electric Brush Assembly and Use Wand Insertion and Release To Insert Insert wand into electric brush until the wand button snaps into place To Remove Lock wands in straight up position Then step on the Wand Quick Release pedal with foot Now pull up on wand WARNING DO NOT attach or remove handle or wands while cleaner is ON This could cause sparking and damage the electrical contacts To Start 1 To lower wand press on the large pedal marked Handle Release 2 Start vacuum and electric brush To Correct amp Reset Overload Protector The overload protector protects the motor from brush Jam ming and belt breakage If the agitator slows d
7. e these accessories with the top and lower electric powerbrush wands They are to be used with the hose or telescopic ratchet wand 13 Wet Pick Up This unit allows the powerful built in central vacuum system to pick up liquid and wet debris but prevents it from entering the vacuum tubing and dirt canister It can be used to unclog drains clean up spills and overflows and even suck out the leftover water when draining hot tubs Capacity Approx 4 gallons WP 312MA Wet Pick Up Unit comes with bucket cart 5 x 1 1 4 hose and 2 cuffs Additional 30 standard hose should also be purchased Do NOT use SFH 630 or any other high or low voltage hose with this product Vibrating Upholstery Tool This tool vibrates the surface being cleaned to loosen dust and dirt allowing you to get a more deep down clean UT 501 For more details on these or any other Lindsay products contact your local Vacu Maid or Astro Vac dealer or visit our websites at www vacumaid com and www astrovac com CARING FOR YOUR CARPET Proper maintenance will extend the time you can enjoy your carpet and help keep its fresh appearance Vacuum regu larly remove spills promptly and extraction clean periodically Use a strong well functioning vacuum cleaner with a powerful airflow adjustable brushes and an enclosed high efficiency filtration bag It 1s best to purchase a vacuum cleaner that bears the CRI Indoor Air Quality Test
8. igned to fit into your cleaning tools A 1 4 turn ensures a good fit To remove the wand give a 1 4 turn in the opposite direction and pull the cleaning tool or handle from the wand 10 L6150 CLEANING ATTACHMENTS amp TOOLS To Attach Tools for Use Simply slide the tool onto end of the telescopic ratchet wand or directly onto stub tube of the hose Tools are to be used with telescopic ratchet wand or handle on hose Do NOT use with top or lower electric brush wands FB 215BLK 12 Floor Brush with Wheels e Works well to clean bare floors wood flooring tile etc e Shorter bristles in front longer in back allows larger dirt particles to be picked up with forward movement For best results do not force the front of the brush down when moving forward Allow the brush to gently glide across the floor The front of the brush should allow particles to enter through the raised bristles CT 630BLK Premium Crevice Tool 13 tool to reach into cracks and crevices such as tracks of sliding glass doors corners along baseboards and even in the cracks of couches and other furniture e Notched end and slotted side vents help maintain air flow and proper suction e This tool has a flat side which makes it great for reaching under refrigerators around air conditioner coils and other hard to reach places that collect a lot of dust and dirt DB 630BLK Premium Dusting Brush e Use for dusting furnishi
9. ing Program label assuring that the cleaner will remove soil well contain the dust within the machine and protect the carpet s appearance he Carpet amp Rug Institute CRI For more information on caring for your carpet please visit the CRI website at www carpet rug com Lindsay Manufacturing Inc www lindsaymfg com Copyright 2004 by Lindsay Manufacturing Inc All rights reserved No part of this publication may be reproduced or transmitted in any form or by any means without written consent Any unauthorized copies will be prosecuted for civil damages to the fullest extent of the law L6150 5 07 O Lindsay Manufacturing Inc 2004 Printed in USA by LMI
10. it when not in use Mount on a wall in a closet garage or any other convenient location for hose storage and place it high enough so you can loop your hose only four times and still clear the floor Mounts using only one stud and two screws 12 L6150 OTHER PRODUCTS AVAILABLE FROM LINDSAY MANUFACTURING INC A variety of accessories and tools are available to complement your ASP kit Below are just a few of the options available Ceiling Fan Brush Kit For the one place we all forget to clean but know that we should we offer the Ceiling Fan Brush Kit This kit helps you reach the tops of your fan blades and ensures that you get rid of all of the dust build up With its unique design and powerful suction it eliminates dust from scattering below CT 5 Pet Grooming Tool This pet tool s soft rubber bristles are great for comfortably removing previously shed hair from a pet s coat PT 530 Hand Held Air Turbine with Crevice Tool This accessory can be used on stairs in vehicles or on upholstery The fold out crevice tool can be used to reach into cracks and crevices or folded back when not needed This tool has an open face which allows the vacuum to clean the corners on the risers of stairs allowing for a more complete clean PB 255 Mini Vacuum Attachment Kit This mini kit is perfect for cleaning small delicate fi al objects computers and keyboards CT 6 Do NOT us
11. ngs such as bookcases tables desks and mantles Also great for dusting picture frames collectibles tops of televisions window sills and even the backs of computer monitors Molded soft vinyl construction less abrasive on delicate furnishings and prevents wall markings Full natural e for gentle cleaning UT 630BBLK Premium Upholstery Tool with Brush e Cleans upholstered furniture drapes mattresses and even works well on vehicle upholstery and carpets e Continuous airflow is critical to cleaning results This tool is designed to prevent airflow from being cut off e The brush strip gently engages upholstery to lift debris and groom surfaces being cleaned CT 3BL Tool Cadd CB 180 Mesh Tool Caddy Bag e Holds accessories and tools making them more manageable e For storing and transporting tools amp accessories H 431 Adds portable convenience by allowing multiple tools to be carried on the wand for quicker and easier access To attach Snap caddy onto wand at an angle beveled side first then slip attachments and tools onto caddy pegs When clipping it onto wand attach it so that the two peg side faces up while the single peg side faces down the wand This will keep your tools on better Plastic Hose Hanger Accessories shown may not be to scale Use of hanger can increase the life of your hose and save space while storing Coil your hose around this hanger to store
12. o valve Lift valve door insert cuff into hole ASP2 Pigtail cord wall end Use with standard pin jack valve To insert hose cuff into valve Lift valve door insert cuff into hole amp plug cord into 110 electrical outlet L6150 9 1 W 535 Top Wand e Connects to lower wand when operating the floor brush Cord management keeps cords out of the way and allows you to disengage the hose handle from the electric brush 2 BW 240 Lower Wand Swivel Wand Connector allows wand to rotate 90 along with wrist movement to provide ease of vacuuming and to prevent strain 3 W 419H Chrome Telescopic Wand e Extension wand can be adjusted to necessary height to lessen back strain and can be extended to reach high areas e Extends from 23 1 2 to 39 in 3 4 increments Hole in the top friction fit on the bottom IMPORTANT Do NOT remove wands while power is on Telescopic Wand Operating Instructions To extend wand Push the black button in the direction of the arrow and hold in place This releases the ratchet and allows the inner wand to be extended The wand can be locked into the desired length by releasing the button at any of the notches To retract the wand hold down on the black button and push the wand back into the outer wand Attaching tools or hose handle to the wand The straight outer wand is designed to fit into your hose handle Insert the wand into the handle The notched inner wand is de s
13. ot be higher than 130 volts 15 watts NS deg 3 Push in and turn the bulb clockwise to replace Bulb must ed lt ae _ Note replacement bulb number is EB26028 WAP 4 Reinstall the electric brush cover as shown in BELT mc CHANGING amp AGITATOR CLEANING section BELT CHANGING AND AGITATOR CLEANING Electric Brush Model Disconnect hose and brush from electrical outlet Frequently check and remove hair string and lint buildup in brush area If buildup becomes excessive disconnect the brush from wand and follow steps below To Remove Belt A Ah nk T 1 Turn the electric brush upside down MAN EN g QUUM y 1 4 1 i ur rem i a a i P m Y AN i L i 1 2 Unscrew the brush cover screws 3 Turn brush over right side up Press handle release pedal and lower the swivel To remove cover grasp the sides and pull out to release the outside cover 5 4 Lift rear latches up and tilt cover forward from back until front snaps free 5 Depress tabs on rear of agitator cover and rotate forward to release from the electric brush base Y Y Agitator Cover NA 4 4 T agm A ANNI v A T n f 1 Wn al M 1 ost n ad u A un N j an gt AY 6 Lift agitator assembly out and re A move worn belt Y To Replace Belt 1 Install new belt over motor drive then over brush sprocket NOTE belt replacement number for is EB29010
14. own or stops the overload protector shuts the brush off To correct problem Unplug electrical cord Check brush area for excessive lint buildup or jamming Overload Protector reset button To reset Press the reset button on top of the brush Plug in and turn on vacuum and brush Pile Height A To Change Pile Setting TN ON Select a pile height setting by using the pile height S M lever on the electric brush The pile height setting is shown on the control The deeper the pile of the carpet the higher the setting Handle Release Pedal Pile Height Pedal Suggested Pile Height Settings For best deep down cleaning use the XLO setting However you may need to raise the height to make some jobs easier As a general guide XLO most carpet heights LO short to medium pile MED medium to long pile HI long pile Electric Brush Care A WARNING Always follow all safety precautions Electric Shock or Personal Injury Hazard when cleaning and Disconnect electrical supply before servicing or cleaning servicing the electric the unit Failure to do so could result in electrical shock or brush personal injury from cleaner suddenly starting LIGHT BULB CHANGING mE Push in Electric Brush Jj an turn 1 Remove the electric brush cover as shown in BELT lt a s d CHANGING amp AGITATOR CLEANING section Sai m 2 Push in and turn bulb counterclockwise then pull A out to remove n
15. t 0 44 EB24044 INDICATOR BLOCK PRE NU A 45 EB24045 SPRING ASSIST ss mt py YE va ss 46 EB30046 WINDOW DIRT SENSOR hk i 47 EB24047 LIFTER MEA 48 EB30048 SCREW t 49 EB31049 PCB SUPPORTER 3 12 50 EB27050 THRUST WASHER JJ LL T B2705 CATCH INDEXING 52 EB27052 WASHER 53 EB27053 RATCHET CATCH 54 EB27054 INDICATOR BLOCK ASSEMBLY EB27055 SCREW SFH 630 Slimfit Style 4 Wire Swivel Electric Crush Proof Hose The slimfit style handle has 360 rotation to minimize kinks effort and in hand weight Three Position Switch For use with the electric brush Allows vacuum to be controlled from the handle Vacuum off Brush off Vacuum on Brush off Vacuum on Brush on Hose Handling Hold the hose and handle in any way you find to be the most comfortable With this new style handle numerous hand positions are offered and reduce strain and increase ease of use Also for added ease while vacuuming try keeping the hose behind you rather than out in front of you Use one hand to hold the handle and the other hand to hold and guide the hose Again do what feels comfort able to you IMPORTANT Make sure power is turned off before removing the hose and handle from the wand Arcing or damage to the electrical contacts can occur if the wand 1s removed while brush power is on ASP1 Direct connect wall end Must be used with an electric inlet valve such as the Electravalve To insert hose cuff int
Download Pdf Manuals
Related Search