Version 1.4
Contents
1. DMX Controller REDWash 3e192 3 5 Ethernet connection The fixtures on a data link are connected to the Ethernet network with an Art Net communication protocol The controlling software from PC or lighting console has to support the Art Net protocol The Art Net communication protocol is a 10 Base T Ethernet protocol based on the TCP IP Its purpose is to allow transfer of large amounts of DMX 512 data over a wide area using standard network technology IP address is the Internet protocol address The IP uniquely identifies any node fixture on a network The Universe is a single DMX 512 frame of 512 channels The the REDWash 3e192 is equipped with 8 pin RJ 45 socket for Ethernet input Use a network cable category 5 with four twisted wire pairs and standard RJ 45 plugs in order to connect the fixture to the network RJ 45 socket front view RJ 45 plug front view 1 TD 5 Not connected l 3 RX 7 Not connected 4 Not connected 8 Not connected Patch cables that connect fixtures to the hubs or LAN sockets are wired 1 1 that is pins with the same numbers are connected together 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 If only the fixture and the computer are to be interconnected no hubs or other active components are needed A cross cable has to be used 1 3 2 6 3 1 4 8 5 7 6 2 7 5 8 4 Ethernet operation All fixtures have to be connected to Ether2. 20 7 down mode ioo RUM Er ia IERI Urn RN D 22 DC 23 9 Error and information messages Siada eriperet eee eei eere orte see esses edit esee ee eue duo 24 10 Technical specifications rt t E EROR GER tO E ED ERE RE EEUU ER 25 11 Cleaning and maintenance inie as eau aa aaa aaa aa aa aaa aaa ay SA iata r aaa aa tinis sies esse sisi sais ss essetis ada nasse sss setas asas inner annees 27 11 1 Replacing the main duse asa ie ettet a reete tee aa Ox tete ave Peg e Pose OW 27 11 2 Replacing the air fi ters ete e rere tere eie ai ie et tr edt a a vt eas 27 REDWash 3e192 FOR YOUR OWN SAFETY PLEASE READ THIS USER MANUAL CAREFULLY BEFORE POWERING OR INSTALLING YOUR REDWash 3 192 Save it for future reference This device has left our premises in absolutely perfect condition In order to maintain this condition and to ensure a safe operation it is absolutely necessary for the user to follow the safety instructions and warning notes written in this manual The manufacturer will not accept liability for any resulting damages caused by the non observance of this manual or any unauthorized modification to the device Please consider that damages caused by manual modifications to the device are not subject to warranty The REDWash 3 192 was designed for indoor use and it is intended for professional applic
3. use the menu to set an Ethernet functional mode Disable Ethernet Disables an Ethernet operation Ethernet control data is received to the Ethernet input of the fixture RJ45 socket Each of fixtures has to be connected to Ethernet Ethernet DMX control data is received to the Ethernet input of the fixture goes throw the fixture to its DMX output fixture works as Ethernet DMX converter In a DMX link only first fixture has to be connected to Ethernet the rest of fixtures make up a standard DMX link Set IP Address Select this menu item to set an IP address The IP address is the Internet protocol address uniquely identifies any node fixture on a network There can t be 2 fixtures with the same IP address on the network Default IP Address a preset IP address you can change only first number of the IP address number 2 or 10 Custom IP Address a fully editable IP address To set the custom IP address 1 Select the Custom IP Address and press the ENTER button 2 Use RNS wheel to adjust he first number of the IP address 3 Press the ENTER button to move on the second number of the IP address 4 Repeat steps 2 and 3 for the third and the fourth number of the IP address If you want to return back on the previous number press the ESC button 16 REDWash 3e192 Set ArtNet Universe use this menu item to set a fixture Universe The Universe is a single DMX 512 frame of 512 channels 6 2 Fixture information
4. Pan Fine Fine control of pan movement Tilt Tilt movement by 280 Tilt Fine Fine control of tilt movement Pan Tilt Speed Pan Tilt Time Max speed tracking mode P T speed set Speed Mode in menu P T Mode Speed from max to min vector mode P T time set Time Mode in menu Pan Tilt Mode Time from 0 1 sec to 25 5 sec Pan Tilt Macro Selection Disabled pan tilt macro Reserved Figure of circle small gt large Figure of horizontal eight small gt large Figure of vertical eight small large Figure of rectangle small gt large Figure of triangle small large Figure of five pointed star small gt large Figure of cross small gt large Pan Tilt Macro Speed Set pan tilt speed channel 5 at O DMX No macro generation Macro generation fast gt slow forwards No macro generation Macro generation slow fast backwards Special Functions Reserved To activate following functions stop in DMX value for at least 3sec and shutter must be closed at least 3sec Shutter channel 26 22 14 10 must be at range of 0 31DMX The functions are active at modes 1 2 3 and 5 only Corresponding menu items are temporily overrided Pan Tilt speed mode Pan Tilt time mode Blackout while pan tilt moving Disabled blackout while pan tilt moving Reserved To activate following reset function stop in DMX value for at least 3 sec Pan Tilt reset Reserved Red LEDs All Arrays Red LEDs
5. and press the ENTER button Use the RNS rotary wheel to select the Editing Program menu and press the ENTER button Select the program you want to edit Program 1 Program 3 and press the ENTER button Select the Edit Steps menu and press ENTER Select the desired program step Step 01 Step 99 and press the ENTER button Now you can edit DMX values for selected items Pan coarse pan DMX value from 0 255 Fade Time the time during during which effects go to the current step value from 0 25 5 sec Step Time the time during which effects last in the current step value from 0 25 5 sec 7 After editing all desired item select Save or Save and Copy and press the ENTER button Save saving the current prog step Save and Copy saving and copying the current prog step to the next prog step 8 Goon next program step and repeat instructions 6 7 9 After creation the program enter the Start Step menu and adjust the first step of the program 10 Enter the End Step menu and adjust the last step of the created program Note you can simply reduce the program length by changing values in either Start Step or End Step menu 6 7 Reset function Pan Tilt The function resets the pan and tilt movement Use this function if the moving head fails to move to programmed position 6 8 Special Functions Effect Adjustment the menu enables to set all fixture effects to the
6. in sequences fast gt slow Shutter open Random strobe effect slow fast Shutter open Dimmer Dimmer intensity from 096 to 10096 Dimmer fine Fine intensity from low to high Type of control step step proportional step proportional proportional step proportional step proportional proportional 5 Control menu map Default settings Bold print REDWash 3e192 Menu Level 1 Menu Level 2 Menu Level 3 Menu Level 4 Menu Level 5 Menu Level 6 Fixture Address DMX Address 001 512 Ethernet Settings Set Ethernet Mode Disable Ethernet Ethernet Ethernet DMX Set IP Address Default IP Address Set ArtNet Universe Custom IP Address 0 255 Fixture Information Power On Time Maximum Mode Total Hours Resetable Hours Economical Mode Total Hours Resetable Hours Air Filters Set Alert Period 10 50 300 hours Elapsed time Fixture temperature Current Head Temp LEDs Temp Max Nonresetable Head Temp LEDs Temp Maximum Resettable Head Temp LEDS Temp DMX Values Pan 0 255 Dimmer Fine 0 255 Software Version IC1B IC2 B IC1 H IC1 DS IC2 DS Product 195 Mac Adr RDM UID Personality User Mode User A Settings User B Settings User C Settings DMX Preset Mode 1 Ch 1 Pan Ch 28 Dimmer fine Set Active Mode 2 Ch 1 Pan Ch 24 Dim
7. the fixture base IC1H the processor in the fixure head controls LEDs module 17 REDWash 3e192 IC1 DS the main display processor on the front panel in the fixture base IC2 DS the display memory on the front panel in the fixture base 6 3 Personality Use this menu to modify the REDWash 39192 operating behaviour User mode The REDWash 3 19 allows you to recall up to 3 user settings After switching the fixture on for the first time the User A settings is active Now all changes made in the Personality menu Fixture Address menu and the Music Trigger and Presetting Playback menu from the Stand alone setting are saved to the User A settings If you now select the User B settings from this moment these changes are saved to the User B settings After switching the fixture off and on the User B setting is active In this way you may use the 3 fixture operating behaviours User A Settings the function recall the user A settings User B Settings the function recall the user B settings User C Settings the function recall the user C settings Pan Reverse Use this function to invert the pan movement Tilt Reverse Use this function to invert the tilt movement DMX Preset Use this function to set desired channel setting Please refer to the chapter DMX protocol for a detail description Display Adjusting This menu allows you to change the display settings Display Permanent On this function
8. 9 REDWash 3e192 Presetting Playback This function allows you to select the program which will be played after switching the fixture on Selected program will be played in a loop Disabled the option disables the Presetting playback function Test Program The option will start built in demo sequences Program 1 the option will start a created program 1 Program 2 the option will a created program No 2 Program 3 the option will start a created program No 3 Note If any program from this menu is has been selected and the fixture is switched off and on and receives a DMX signal the fixture does not reply to DMX and will run the selected program Playing program Use this menu to run a desired program in a loop Test Program In Loop the option starts built in demo program Program 1 In Loop the option starts created program No 1 Program 2 In Loop the option starts created program No 2 Program 3 In Loop the option starts created program No 3 Select the program you wish to run and press the ENTER button The selected program starts running By pressing the ENTER button again the program will be paused Editing Program Use this menu to edit or create program The REDWash 3e192 has one built in program and the 3 free programs each up to 99 steps Step time the time during which effects last in the current step Procedure 1 Use the RNS rotary wheel to find the Stand alone setting menu
9. Array 3 Blue LEDs saturation control 0 100 proportional M wo M u1 White LEDs Array 3 White LEDs saturation control 0 100 Proportional uy o Red LEDs Array 4 Red LEDs saturation control 0 100926 proportional N ay N Green LEDs Array 4 Green LEDs saturation control 0 100 proportional Blue LEDs Array 4 Blue LEDs saturation control 0 100 proportional N N White LEDs Array 4 White LEDs saturation control 0 100 Proportional me ey wo 7 w N my o Colour Macros No macro Macro 1 Macro 2 Macro 3 Macro 4 Macro 5 Macro 6 N M ES ES EJ ES Ez cs EJ a EJ Mode 1 Channel REDWash 3e192 56 63 64 71 72 79 80 87 88 95 96 103 104 111 112 119 120 127 128 135 136 143 144 151 152 159 160 167 168 175 176 183 184 191 192 199 200 207 208 215 216 223 224 231 232 239 240 247 248 255 0 31 32 63 64 95 96 127 128 143 144 159 160 191 192 223 224 255 13 Macro 7 Macro 8 Macro 9 Macro 10 Macro 11 Macro 12 Macro 13 Macro 14 Macro 15 Macro 16 Macro 17 Macro 18 Macro 19 Macro 20 Macro 21 Macro 22 Macro 23 Macro 24 Macro 25 Macro 26 Macro 27 Macro 28 Macro 29 Macro 30 Macro 31 Shutter Strobe Shutter closed Shutter open Strobe effect slow fast Shutter open Opening pulses in sequences slow fast Closing pulses
10. REDWash 3 192 USER MANUAL Version 1 4 ROBE Lighting s r o Czech republic www robe cz REDWash 3e192 Table of contents 1 Safety instFUCtiOls aiite az cadet te OE A RATA A A A OO OAI T W ATE 3 2 Fixt re exterior VIEW a et e d cete m z a Leto ve erent ene alien Ce root one 5 3 IMstallatiomy aiz EE 6 3 1 Mounting the fIXE re AO OO A AA AA vy ge enata eae OO abr eE ve RENE PERS Rat 6 3 2 Changihg the leris af Fay eoe e eet Bees doe eet eve ree dote ep ve ertet 6 3 3 Connection to the aeo on tte eee P pee ee En eve 8 34 DMX 512 CONNECUION i i aeneo Saa ra eaa edic mee dada ore i opi 8 3 5 Ethernet connection ai A A lote p at te t a tot tea etat t e t n tede 9 REDWash 30192 DMX protocol teo eta av I D Ue p at ee ed i e RM UE 11 Hx Gontrolfienu maps ed HEU eB 14 6 IFIxt re MEN cee A GAL tdi e st ist ud cest in OO eee aed 16 6 1 Fixture AGO eL E O O AA AO AE nue A ONE W WAKE 16 62 Fixt re information AE O ERREUR b RED Re Ee ir PERDE OE LK Rut 17 6 3 Personality ictor tr breves eue Sess de 18 6 4 Test SEque ces a asia A O AO O DOO JA O AO A 19 S ERNIEBuP IE 19 6 6 Standalone setting cre rp E Ene UNE ADO D RESP re 19 6 7 Reset f nCtion ne eret et t ere EUR Ly RE EFIE eee teas pea EE eene 20 6 8 Special Functions oet ern eee c tee e E tt pee ies reb east
11. Save and Copy Start Step Step1 Step 99 End Step Step1 Step 99 Reset Function Pan Tilt Special Functions Effect Adjustment DMX Values Pan Dimmer Fine Calibrate Values RED LEDs 1 White LEDs 4 Save Load Def Values Updating Software 15 REDWash 3e192 6 Fixture menu The fixture menu allows to set the fixture according to your needs obtain information on its operation test its various parts and lastly program it if it has to be used in a Stand alone mode Control elements on the front panel The RNS rotary wheel used to move between menu items on the same level or adjusts values The ESC button used to leave menu without saving changes The ENTER button used to enter menu confirms adjusted values and leaves menu After switching the fixture on the display shows the initial screen ADVANCED TECHNOLOGY Press the ENTER button the display shows current address DMX ADDRESS 001 The main menu of the control panel is accessed by pressing the ENTER button To browse through the menu rotate the RNS wheel To select a menu item press the ENTER button 6 1 Fixture Address DMX Address Use the menu to set the DMX start address of the fixture which is defined as the first channel from which the Rewash 3e192 will respond to the controller Ethernet Settings The menu provides all needed settings for an Ethernet operation Set Ethernet Mode
12. Use this menu to read useful information about the fixture status Power On Time Use the menu item to read the number of operation hours for each LEDs operating mode Total Hours the function shows the total number of the operation hours since the REDWash 3e192 has been fabricated Resettable Hours the function shows the number of the operation hours that the REDWash 3e192 has been powered on since the counter was last reset In order to reset this counter to 0 press the ENTER button twice Air Filters Regular cleaning of the air filters is very important for the fixture s life and performance Build up of dust dirt and fog fluid residues reduces the fixture s light output and cooling ability The two items of this menu help you to keep cleaning period of the air filters Set alert period cleaning schedule for the fixture depends on the operating environment It is therefore impossible to specify accurate cleaning interval This function allows you to change the cleaning interval of the air filters This alert value is 50 hours and it is set as default Inspect the fixture within its 50 hours of operation to see whether cleaning is necessary If cleaning is required clean all air filters and change the value in this menu on acceptable level Min level of alert period is 10 hours max is 300 hours Elapsed Time the option allows you to read the time which remains to cleaning air filters The time period is set in the menu me
13. allows you to keep the display permanent on or to turn it off automatically 2 minutes after last pressing any button on the control panel Display Intensity select this function to adjust the display intensity 1 min 10 max Display Backlight select this function to adjust the display backlight 1 min 10 max Display Turned select this function to turn the display by 180 Blackout d M C This function enables to close a light output while the moving head returns back to its correct position which has been changed by an external force Pan Tilt Feedback This function allows to return the mowing head to the required pan tilt position after changing its position by an external force e g by a stroke Be careful the Pan Tilt Feedback OFF is not a standard operation mode and the fixture head can be damaged Microphone Sensitivity Select this function to adjust the microphone sensitivity from 1 maximum to 20 minimum If the sensitivity is correctly adjusted the symbol blinks in bass beats Pan Tilt mode Use this menu to set the mode of the pan tilt movement Time mode the pan and the tilt will move with different speeds and they will come at the same time to the end point of their track pan and tilt use their optimal speeds Speed Mode Pan and tilt will move with the same speed as adjusted at the channel 5 Pan Tilt speed Active Blackout while Use this menu if you wish to close the light output du
14. ance Repeat steps 6 7 for this channel 10 Use the RNS rotary wheel to select the last colour the Blue balance and repeat steps 6 7 for this colour M 9 Uu LEDs Output Power The menu allows to choose 2 different operating modes for fixture s LEDs Maximum Max light output Maximum light output Note in this mode the total lumen maintenance is 7096 at 10 000 hours Economical The light output is decreased by 20 The total lumen maintenance is 7096 at 60 000 hours Default Settings The menu item sets all fixture parameters to the default factory values 6 4 Test sequences Use this menu to run demo test sequences without an external controller which will Show you some possibilities of using the REDWash 39192 Mode 1 This mode is suitable for projections on the wall ceiling or ground without any head movement Mode 2 This mode uses all REDWash 39192 functions including pan tilt movement and therefore is suitable for a complete introduction of the fixture 6 5 Manual mode Preset Effects Select this menu to call up preset channel effects Manual Effect control Use this menu for full control of each channel effect 6 6 Stand alone setting Use this menu to set options used in stand alone mode as a selection of the running program programming and modifying programs Music Trigger Select this function to enable the sound control of the running programs via the built in microphone 1
15. are Uploader is the same for both versions IIl Fixture software updating 1 Determine which of your ports is available on your PC and connect it with the DMX input of the fixture if you using the flash cable RS232 DMX with the DMX input of the DreamBox if you using the USB cable Disconnect the fixture from the other fixtures in a DMX chain Turn both the computer and the fixture on Make sure the lamp is switched off only if the fixture involves a lamp 2 Switch the fixture to the updating mode 1 Use the RNS rotary wheel to find the Special Functions menu Press the ENTER button Use the RNS rotary wheel to select the Updating Software item Press the ENTER button Use the RNS rotary wheel to select Yes option Press the ENTER button Note If you do not want to continue in software update you have to switch off and on the fixture to escape from this menu We recommend to cancel all running programs before start the Software Uploader 3 Run the Software Uploader program Select desired COM and then click on the Connect button UT RB W 21 REDWash 3e192 ColorSpot 700EAT Software Uploader v3 0 Select COM if the T serial port is used ea Select DreamBox1 z Connect if the USB port is incremental Update used If the connection is OK click on the Start Uploading button to start uploading It will take several minutes to perform software update If the option Incremental Upd
16. ate is not checked all processors will be updated including processors with the same software version If you wish to update only later versions of processors check the Incremental Update box Avoid interrupting the process Update status is being displayed in the Info Box window When the update is finished the line with the text The fixture is successfully updated will appear in this window and the fixture will reset with the new software Note In the case of an interruption of the upload process e g power cut the fixture keeps the updating mode and you have to repeat the software update again For example The fixture was switched off before finishing software upload After switching again the fixture on the fixture is still in the updating mode and the display is dark Restart the Software Uploader program and repeat software update from your PC 7 Power down mode This mode omits fixture reset after switching it on and reduces the power of motors The Power down mode is useful in special cases if the fixture is in a flight case and you want to set its DMX address without taking it out from the case To enter the Power down mode press and hold the ENTER button and at the same time switch the power switch The following message appears on the display Really Skip Initial Reset Escape Enter Press the ENTER button to activate the Power down mode without fixture reset Now you can set DMX addres
17. ation only It is not for household use 1 Safety instructions DANGEROUS VOLTAGE CONSTITUTING A RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THIS UNIT Make sure that the available voltage is not higher than stated on the rear panel of the fixture This fixture should be operated only from the type of power source indicated on the marking label If you are not sure of the type of power supplied consult your authorized distributor or local power company Always disconnect the fixture from AC power before cleaning removing or installing the fuses or any part Make sure that the power switch is set to off position before you connect the fixture to the mains The power plug has to be accessible after installing the fixture Do not overload wall outlets and extension cords as this can result in fire or electric shock Do not allow anything to rest on the power cord Do not locate this fixture where the cord may be damaged by persons walking on it Make sure that the power cord is never crimped or damaged by sharp edges Check the fixture and the power cord from time to time Refer servicing to qualified service personnel This fixture falls under protection class I Therefore this fixture has to be connected to a mains socket outlet with a protective earthing connection Do not connect this fixture to a dimmer pack Do not look straight at the fixture front LEDs during operation The intense light beam may damage your eyes If the fixtur
18. be placed directly on the stage floor or rigged in any orientation on a truss without altering its operation characteristics The installation of the fixture has to be built and constructed in a way that it can hold 10 times the weight for 1 hour without any harming deformation When rigging derigging or servicing the fixture staying in the area below the installation place on bridges under high working places and other endangered areas is forbidden For overhead use always install a safety rope that can hold at least 10 times the weight of the fixture You must only use safety ropes with screw on carbines Pull the safety rope through the two apertures on the bottom of the base and over the trussing system etc Insert the end in the carbine and tighten the fixation screw Rigging the fixture via omega holders 1 Bolt the clamp 1 to the omega holder 4 with M12 bolt 2 Fasten the omega holders to the bottom of the base by inserting both quick lock fasteners 3 into the holes of the base and tighten fully clockwise 3 Fasten the safety rope 2 through the two apertures on the bottom of the base and over the trussing system 3 2 Changing the lens array The REDWash 3e192 has a 25 lens array module fitted as standard and is also supplied with a glass holder module for frost filters and a grid module REDWash 3e192 If you wish to change the lens module follow this procedure 1 Switch the fix
19. desired positions before fine calibration DMX Values the menu item enables to control all fixture effects and take the light beam at the wall before calibrating each LEDs array 20 REDWash 3e192 Calibrate Values the menu serves for fine calibration of LEDs current during fixture burn in at a factory Each LEDs array can be calibrated separatelly Users should not change these settings Updating Software The menu item allows you to update software in the fixture via either serial or USB port of PC The following are required in order to update software PC running Windows 95 98 2000 XP or Linux DMX Software Uploader Flash cable RS232 DMX No 13050624 if you want to use a serial port of Dreambox if you want to use an USB port of PC Note1 Software update should execute a qualified person If you lack qualification do not attempt the update yourself and ask for help your ROBE distributor Note 2 DMX address IP address programs 1 3 and all items in the menu Personality will be set to their default factory values To update software in the fixture 1 Installation of the DMX Software Uploader 1 DMX Software Uploader program is available from the ROBE web site at WWW robe cz 2 Make a new directory e g Robe Uploader on your hard disk and download the software to it 3 Unpack the program from the archive If the Robe fixture is produced in both magnetic and electronic ballast version name of DMX Softw
20. e has been exposed to drastic temperature fluctuation e g after transportation do not switch it on immediately The arising condensation water might damage your device Leave the device switched off until it has reached room temperature REDWash 3e192 Do not shake the fixture Avoid brute force when installing or operating the fixture This fixture was designed for indoor use only do not expose this unit to rain or use near water When choosing the installation spot please make sure that the fixture is not exposed to extreme heat moisture or dust Air vents and slots in the fixture s head and base are provided for ventilation to ensure reliable operation of the device and to protect it from overheating The openings should never be covered with cloth or other materials and never must be blocked This fixture should not be placed in a built in installation unless proper ventilation is provided Only operate the fixture after having checked that the housing is firmly closed and all screws are tightly fastened Always use a secondary safety cable when mounting this fixture Make sure that the area below the installation place is blocked when rigging derigging or servicing the fixture Do not block the front objective LEDs with any object when the fixture is under operation The fixture becomes very hot during operation Allow the fixture to cool approximately 20 minutes prior to manipulate with it Operate the fixture only after havin
21. er products may have better light output than previous products 26 REDWash 3e192 11 Cleaning and maintenance It is absolutely essential that the fixture is kept clean and that dust dirt and smoke fluid residues must not build up on or within the fixture Otherwise the fixture s light output will be significantly reduced Regular cleaning will not only ensure the maximum light output but will also allow the fixture to function reliably throughout its life A soft lint free cloth moistened with any good glass cleaning fluid is recommended under no circumstances should alcohol or solvents be used DANGER Disconnect from the mains before starting any cleaning or maintenance work The glass holder and lens modules will require weekly cleaning as smoke fluid tends to building up residues reducing the light output very quickly The cooling fans should be cleaned monthly The interior of the fixture should be cleaned at least annually using a vacuum cleaner or an air jet More complicated maintenance and service operations are only to be carried out by authorized distributors 11 1 Replacing the main fuse Only replace the fuse by the one of the same type and rating To replace the fuse 1 Disconnect the fixture from mains 2 Unscrew the fuse holder on the rear panel of the base with a fitting screwdriver from the housing anti clockwise 3 Remove the old fuse from the fuse holder Install the new fuse in the fuse holder 5 Re
22. g familiarized with its functions Do not permit operation by persons not qualified for operating the fixture Most damages are the result of unprofessional operation Please use the original packaging if the fixture is to be transported Please consider that unauthorized modifications on the fixture are forbidden due to safety reasons If this device will be operated in any way different to the one described in this manual the product may suffer damages and the guarantee becomes void Furthermore any other operation may lead to dangers like short circuit burns electric shock crash etc Release the pan and tilt locks before operating the fixture 2 Fixture exterior view REDWash 3e192 Lens array Head Tilt lock Arm Air vent Base Front panel Pan lock Holder Front panel of fixture base LCD display RNS rotary wheel Escape button Pw NP Enter button Rear panel of the fixture base Power switch Main fuse Power cord DMX output 5 pin XLR DMX input 5 pin XLR DMX output 3 pin XLR DMX input 3 pin XLR Ethernet input RJ 45 No WP wn Pp REDWash 3 192 3 Installation 3 1 Mounting the fixture Use 2 clamps to mount the fixture on the truss Follow the instructions mentioned at the bottom of the base Make sure that the device is fixed properly Ensure that the structure truss to which you are attaching the fixtures is secure The fixture can
23. if the head s magnetic indexing circuit malfunctions sensor failed or magnet is missing or the stepping motor is defective or its driving IC on the PCB The head is not located in the default position after the reset 24 REDWash 3e192 10 Technical specifications Power supply Electronic auto ranging Input voltage 100 250V AC 50 60 Hz Fuse T8A Max power consumption 230V 450 W Economical mode 750W Maximum mode Optic amp Effects Light source 192 Luxeon Rebel LEDs RGBW Optical system 12 without lens array 25 lens array standard 45 and 45 x 15 lens arrays optional Easy fitting of additional frost film filters Typical Lumen Maintenance 70 60 000 hours Economical mode Lumen Maintenance 70 10 000 hours Maximum mode RGBW colour mixing Built in colour macros Adjustable strobe sequences White colour balance adjusting Electronics Strobe Control panel graphic LCD display and ROBE navigation system Control USITT DMX 512 RDM support Art Net protocol ready for ACN DMX protocol modes 5 8 16 24 or 28 control channels Control options DMX Auto trigger Audio trigger Operations modes DMX Stand alone Manual control of all effects via control panel Strobe effect with variable speed max 20 flashes per sec Pre programmed random strobe pulse effects Dimmer Smooth 16 bit dimming from 0 100 Connections DMX data in out Locking 3 pin and 5 pin XLR AC power inp
24. mer fine Set Active Mode 3 Ch 1 Pan Ch 16 Dimmer fine Set Active Mode 4 Ch 1 Pan Ch 8 White LEDs Set Active Pan Reverse On Off Tilt Reverse On Off Display Adjusting Display Permanent On On Off Display Intensity 1 6 10 Display Backlight 1 5 10 Display Turned On Off Blackout d M C On Off Pan Tilt Feedback On Off 14 Menu Level 1 Menu Level 2 REDWash 3e192 Menu Level 3 Menu Level 4 Menu Level 5 Menu Level 6 Microphone Sensitivity 1 10 20 Pan Tilt mode Time Speed Active Blackout While Pan Tilt Moving On Off IR Sensor On Off Init Effect Positions Pan 0 255 Dimmer Fine 0 255 Save Temperature Unit C F White Balance On Off White Balance Setting Red 0 200 255 Green Qui 255 Blue 0 237 255 LEDs Output Power Maximum Economica Default Setting Test Sequences Mode 1 Pan 0 255 Tilt 0 255 Run Test Program Mode 2 Manual Mode Preset Effect Control Pan Position 1 7 Dimmer Position 1 6 Manual Effect Control Pan 0 255 Dimmer Fine 0 255 Stand alone Setting Music Trigger On Off Preset Playback Disabled Test program Program 1 Program 3 Playing Program Test Program in Loop Program 1 in Loop Program 3 in Loop Editing Program Program 1 Edit Steps Step 1 Pan 0 255 Program 3 Step 99 Dimmer Fine 0 255 Fade T 0 1 25 5s Step T 0 1 25s Save
25. net via patch cables and a data switch The option Ethernet has to be selected from the Set Ethernet Mode menu on each fixture Set a proper IP address and an Universe for each fixture Example Control PC Data Switch An advised PC setting IP address 002 xxx xxx xxx 010 xxx xxx xxx different from fixture IP NET mask 255 0 0 0 REDWash 3e192 Ethernet DMX operation Only first fixture is connected to Ethernet and the rest of fixtures make up a standard DMX link The option Ethernet DMX has to be selected from the Set Ethernet Mode menu on the first fixture connected to the network Next fixtures have standard DMX addressing Caution At the last fixture the DMX clink has to be terminated with a terminator Solder a 120 Ohm resistor between Signal and Signal into a XLR plug and connect it to the DMX output of the last fixture Example 10 Version 1 1 Mode 1 Mode 2 Mode 3 Channel Channel Channel REDWash 3e192 REDWash 3192 DMX protocol Mode 4 Channel EZ 0 9 10 31 32 63 64 95 96 127 128 159 160 191 192 223 224 255 0 1 127 128 129 130 255 200 209 210 255 11 Pan Pan movement by 530
26. ntioned above Expired time period is signalized by a negative mark at the time value and a warning icon triangle on the display with the following message Clean Air Filters Clean the filters and reset this menu item by pressing the ENTER button twice while this menu is highlighted to start the new time countdown Fixture Temperatures Select this menu to read the temperatures of the fixture Current the current temperature of the fixture inside Maximum nonresettable the menu item shows the max temperatures of the fixture inside since the REDWash 39192 has been fabricated Maximum resettable the menu item shows the maximum temperatures of the fixture inside since the counter was last reset In order to reset desired counter to O press the ENTER button twice Note The ambient temperature should not exceed 40 C Measuring points LEDs Temp the temperature of the LEDs module Head Temp the temperature on the PCB in the fixture head The temperatures can be displayed in either C or F units see option Temperature unit in the Menu Personality DMX Values Select this function to read DMX values of each channel received by the fixture Product IDS Select this function to read either the MAC address or the RDM UID figure Software Version Select this function to read the software versions of the fixture processors IC1 MB the processor in the fixture base controls pan tilt movement IC2 MB EEprom in
27. place the fuse holder in the housing and screw it 5 11 2 Replacing the air filters The REDWash 3e192 is supplied with 2 air filters placed in the fixture head Clean the air filters with a vacuum cleaner or you can wash them and put back dry To replace the air filters 1 Disconnect the fixture from mains 2 Raise up a filter cover 1 fastened with two magnets on the top head cover Pull out the air filter 2 Clean or replace the air filter Snap the filter cover back to the head cover Repeat steps 2 5 for the bottom cover Reset the item Elapsed Time in the Fixture Information Fixture Information Air Filters Elapsed Time NOU Pw Specifications are subject to change without notice March 5 2009 27
28. ring effect changes Pan Tilt Moving the menu item enables to close a light output while the pan tilt coordinates Are changing IR Sensor Select this function to switch on off the infra red remote control 18 REDWash 3e192 Init Effect Positions Use this function to set all effects to the desired positions to which they will move after switching the fixture on if DMX is not being received Temperature Unit Use this menu in order to display the fixture temperatures in desired units C or F Balance Use this menu item to enable On or disable OFF the white balance which is set in the White colour balance menu below f this function is set OFF the REDWash 39192 will use maximum values 255 of saturation for red green and blue colour This function has to be set on before adjusting a white balance White Colour Balance The menu gives access to the setting of the white balance To set white colour balance 1 Usea DMX controller or the Manual Mode menu to set all LEDs on max saturation Use the RNS rotary wheel to find the Personality menu Press the ENTER button Use the RNS rotary wheel to select the White Colour balance menu Press the ENTER button and the Red Balance item will appear on the display Press the ENTER button and use RNS rotary wheel to set new max value for the red LEDs Press the ENTER button to confirm the choice Use the RNS rotary wheel to select next colour Green Bal
29. s and behaviour of the fixture by using the Personality menu If you want to go to the normal operation mode run a fixture reset Note All motors inthe Power down mode are deactivated 22 REDWash 3e192 8 RDM This fixture is ready for RDM operation RDM Remote Device Management is a bi directional communications protocol for use in DMX512 control systems it is the new open standard for DMX512 device configuration and status monitoring The RDM protocol allows data packets to be inserted into a DMX512 data stream without adversely affecting existing non RDM equipment By using a special Start Code and by complying with the timing specifications for DMX512 the RDM protocol allows a console or dedicated RDM controller to send commands to and receive messages from specific moving lights RDM allows explicit commands to be sent to a device and responses to be received from it The list of commands for the REDWash 3e192 is the following SS DEVICE HOURS 23 REDWash 3e192 9 Error and information messages Pan Error 1 Pan Error 2 This message will appear after the reset of the fixture if the yoke s magnetic indexing circuit malfunctions sensor failed or magnet is missing or the stepping motor is defective or its driving IC on the PCB The yoke is not located in the default position after the reset of the fixture Tilt Error 1 Tilt Error 2 This message will appear after the reset of the fixture
30. saturation control 0 10096 Type of control proportional proportional proportional proportional step proportional proportional proportional proportional proportional proportional proportional proportional proportional proportional proportional proportional REDWash 3e192 Mode 1 Type Channel Channel of control 2 Green LEDs Arrays Green LEDs saturation control 0 10096 proportional Blue LEDs All Arrays Blue LEDs saturation control 0 10096 proportional White LEDs All Arrays White LEDs saturation control 0 10096 proportional Red LEDs Array 1 Red LEDs saturation control 0 10096 proportional kM w Green LEDs Array 1 Green LEDs saturation control 0 100 proportional HM eo ay N Blue LEDs Array 1 Blue LEDs saturation control 0 100 proportional M M M u1 White LEDs Array 1 White LEDs saturation control 0 100 Proportional ma o Red LEDs Array 2 Red LEDs saturation control 0 10096 proportional 2 N Green LEDs Array 2 Green LEDs saturation control 0 100 proportional R Blue LEDs Array 2 Blue LEDs saturation control 0 100 proportional White LEDs Array 2 White LEDs saturation control 0 100 Proportional Red LEDs Array 3 Red LEDs saturation control 0 100 proportional Green LEDs Array 3 Green LEDs saturation control 0 100 proportional M ma R Blue LEDs 3
31. ture off 2 Shift the security lock 1 to the open posititon black mark 3 Press and hold the lens module lock 2 on the side cover of the fixture head and gently lift the module 3 upward at the side where this lock is pressed 4 Press and hold the lens module lock 2 on the opposite side of the fixture head and gently lift the lens module 3 from its placing and remove it 5 Fit the new lens module into the fixture head and gently push it downward until the module snaps in Make sure that the lens module locks 2 are properly locked Ensure the security lock is in the locked position RED mark before starting the fixture operation t is possible to install a plastic film to the glass holder module in order to get frost light 1 Uninstall the 25 lens array module 1 as described above 2 Insert the plastic film 2 into the slots under partitions in the glass holder module 3 Install the glass holder module back to the fixture s head as described above The shape dimensions of the plastic film depends on its thickness and elasticity We advice to use 2 shapes of plastic films Film thickness lt 0 5mm Film thickness gt 0 5 mm 4 40 5 18 99 302 pa Maximum thickness of the film is 0 8mm REDWash 3e192 You can also use the grid module and put the plastic film under this module 3 3 Connection to the mains Install a suitable plug on the po
32. ut 1 5 m power cord without plug Ethernet RJ45 Pan Tilt Rigging Pan movement range 530 Tilt movement range 280 8 16 bit movement resolution Automatic pan tilt position correction Built in Pan Tilt macros Mounting points 2 pairs of 4 turn locks 2x Omega bracket with turn quick locks Safety chain cord attachment point 25 REDWash 3e192 Temperatures e Maximum ambient temperature 40 104 e Maximum housing temperature 70 158 F Total heat dissipation e Maximum 2217 BTU hr thermal energy 188 BTU hr light energy at 230V 50Hz 120V 60Hz e Typical 1467 BTU hr thermal energy 113 BTU hr light energy at 230V 50Hz 120V 60Hz Acoustic e Noise level below 39 dBa at 1 m 3 3 ft steady state effects in static positions full power all LEDs at max intensity ambient temperature 20 C 68 F Dimensions mm Weight e 22 48 5165 Included items e 1xREDWash 3e192 e 1xLens module 25 No 99012301 installed in the fixture 1xglass holder for frost filters No 10980055 1xgrid module No 17040456 e 2xMounting bracket Omega CL assembled e 1x User manual Optional accessories e Flash cable RS232 DMX No 13050624 e Remote control IR No 13050419 e Lens module 45 No 10980053 e Lens module 15 x45 No 10980054 Note By reason of the fast moving development of LED technology lat
33. wer cord note that the cores in the power cord are colored according to the following table Core Eu Core US Connection Plug Terminal Marking Brown Black Live L Light blue White Neutral N Yellow Green Green Earth The earth has to be connected 3 4 DMX 512 connection The fixture is equipped with both 3 pin and 5 pin XLR sockets for DMX input and output Only use a shielded twisted pair cable designed for RS 485 and 3 pin 5 pin XLR connectors in order to connect the controller with the fixture or one fixture with another Wiring of the XLR connectors DMX output DMX input XLR mounting sockets rear view XLR mounting plugs rear view Ls Ld 50 o1 40 903 3 1 Shield 2 Signal 3 Signal 4 4 Not connected 5 Not connected To build a DMX chain 1 Connect the DMX output of the controller directly with the DMX input of the first fixture in the DMX chain 2 Connect the DMX output of the first fixture in the DMX chain with the DMX input of the next fixture 3 Always connect the DMX output with the input of the next fixture until all fixtures are connected Do not overload the link Max 32 fixtures may be connected on a DMX link Caution Terminate the link by installing a termination plug in the output of the last fixture The termination plug is a male 3 pin XLR plug with a p Ohm resistor soldered between IE l and Signal
Download Pdf Manuals
Related Search