Home

JVC InteriArt HV-36P38SJE User's Manual

1. For 16 9 aspect ratio pictures that have been squeezed into a normal picture 4 3 aspect ratio use the FULL mode to restore the picture to its original shape B Choose the ZOOM mode 1 Press the ZOOM button to display the ZOOM menu AUTO REGULAR PANORAMIC 14 9 ZOOM 16 9 ZOOM 16 9 ZOOM SUBTITLE LL D0009 EN 2 Press the V A buttons to choose a ZOOM mode Then press the OK button The picture expands and the chosen ZOOM mode is displayed in about 5 seconds The ZOOM mode may be automatically changed by the control signal from an external device When you want to return to the previous ZOOM mode choose the ZOOM mode again Remote control buttons and functions B Adjusting the visible area of the picture If subtitles or the top or bottom of the picture are cut off you can adjust the visible area of the picture manually 1 Press the ZOOM button The ZOOM menu appears 2 Press the OK button to display the ZOOM mode indicator The indicator appears 16 9 ZOOM e D0010 EN 3 While it is displayed press the W A buttons to change the position of the picture You cannot adjust the visible area in REGULAR or FULL mode 3D CINEMA SOUND function You can enjoy sounds with a wider ambience This function does not work for the sound from headphones Press the 3D button and choose ON MONO or OFF ON Choose to add the 3D CINEMA SOUND effect to
2. AUTO LOW AUTO HIGH The TV will automatically adjust the level of the DIGITAL VNR effect to match the amount of noise in the picture giving you the best possible picture e If you set the DIGITAL VNR effect too high it can make the picture less sharp It is recommended you use the AUTO LOW setting if you can If you set the DIGITAL VNR function to AUTO LOW but still notice some noise change the setting from AUTO LOW to AUTO HIGH MIN The level of the DIGITAL VNR effect is set to the minimum If you set the DIGITAL VNR function to AUTO LOW but feel that the sharpness of the original picture has not been reproduced fully change the setting from AUTO LOW to MIN The MIN setting is not suitable for low quality pictures which contain a lot of noise MAX The level of the DIGITAL VNR effect is set to the maximum If you set the DIGITAL VNR function to AUTO HIGH but still notice some noise change the setting from AUTO HIGH to MAX e The MAX setting is not suitable for high quality pictures which contain very little noise B Super DigiPure The Super DigiPure function uses the latest in digital technology to give you a natural looking picture The Super DigiPure function includes the following two functions DigiPure function This function helps to create a natural looking picture by eliminating unnecessary edges from high contrast and crisp images For images with low contrast edges are
3. To quit the D I S T demonstration Press the yellow button T V button V A buttons or any of the number buttons CONTENTS Setting up your TV 5 Connecting the aerial and video cassette recorder VOR dci 5 Connecting and placing the woofer unit HV 36P38SJE only 7 Connecting the power cord to the AC OUUIC eT 8 Putting the batteries into the remote COMTO Mme CUR NE DER petet MEM 8 Initial 05 8 T V LINK functions 12 TV buttons and functions 13 Turn the main power on 14 Turn the TV on from standby mode 14 Choose TV channel 14 Adjust the volume 14 Remote control buttons and functions uid eret een etes Er 15 Turn the TV on or off from standby mode 15 Choose a TV channel and watch images from external devices 16 Adjust the volume 17 Information function 17 ZOOM TUCO Mine es orate ee de test 18 3D CINEMA SOUND function 19 Return to TV channel instantly 19 Using the FREEZE function 19 Using the MULTI PICTURE function 20 Operating a JVC brand VCR or DVD LAY ecd sat
4. CC 30 30 38 SET UP menu LANGUAGE The LANGUAGE setting which was performed in the Initial settings page 8 can be changed 1 Choose LANGUAGE then press the OK button A sub menu of the LANGUAGE function appears Gh gt LANGUAGE ENGLISH 1 b FRANCAIS DEUTSCH ITALIANO SVENSKA OMI CASTELLANO NEDERLANDS DANSK NORSK D0002 E EN 2 Press the 4 5 and V A buttons to choose a language Then press the OK button PICTURE TILT There are cases where the Earth s magnetic field may make the picture tilt or make unnatural colours appear in the corner of the screen If this happens you can correct it 1 Choose PICTURE TILT then press the OK button The sub menu of the PICTURE TILT function appears Gah gt gt PICTURE TILT D0018 EN 2 Press the V A buttons until the picture becomes level Then press the OK button DECODER EXT 2 If you have a decoder connected to a T V LINK compatible VCR which in turn is connected to the EXT 2 terminal use the DECODER EXT 2 function to unscramble the scrambled TV channels 1 Turn on the decoder power 2 Display the scrambled TV channel on the TV Even if the decoder is working a scrambled picture appears 3 Display the SET UP menu and choose DECODER EXT 2 AUTO PROGRAM k EDIT MANUAL LANGUAGE PICTURE TILT DECODER EXT 2 EXT SETTING D0029 EN 4 Pr
5. Then press the OK button PAL PAL system SECAM SECAM system NTSC 3 58 NTSC 3 58 MHz system NTSC 4 43 NTSC 4 43 MHz system PICTURE menu AUTO This function detects a colour system from the input signal You can only use this when you are viewing a picture from programme number PR 0 AV or an EXT terminal The AUTO function may not function properly if you have poor signal quality If the picture is abnormal in the AUTO function choose another colour system manually When in the Programme numbers PR 0 AV to PR 99 you cannot choose NTSC 3 58 or NTSC 4 43 SECAM cannot be chosen when the COUNTRY setting is UNITED KINGDOM e COLOUR SYSTEM cannot be chosen when you are watching the EXT 4 picture B 4 3 AUTO ASPECT You can choose one of three ZOOM modes REGULAR PANORAMIC or 14 9 ZOOM as the ZOOM mode for the normal picture 4 3 aspect ratio 1 Choose 4 3 AUTO ASPECT then press the OK button gt gt 4 3 AUTO ASPECT PANORAMIC REGULAR 14 9 ZOOM Ow CNY D0017 EN 2 Press the V A buttons to choose a ZOOM mode SOUND menu 0 souno STEREO I I BASS TREBLE BALANCE HEADPHONE VOLUME 3D CINEMA SOUND gt D0019 EN Functions in the SOUND menu other than HEADPHONE VOLUME work for the TV speakers They do not work for the sound from the headphones When the headphones are connected and only one screen 15 displ
6. name ID you want to give the TV of the AUTO PROGRAM page 33 channel procedure and set the COUNTRY setting to FRANCE before pressing the OK button A CH CC number unique to this TV and corresponding to the Channel number of a TV channel is required Find the corresponding CH CC number from a table CH CC NUMBER on page 37 puer based on the Channel number of the TV channel D0032 EK 35 36 SET UP menu When the COUNTRY setting is not FRANCE use a two digit CH CC number When the COUNTRY setting is FRANCE use a three digit CH CC number B INSERT 1 Press the V A buttons to choose programme number PR for which you will register a new TV channel Press the green button and start the INSERT function D0034 EK To cancel the INSERT function Press the BACK button When the COUNTRY setting is UNITED KINGDOM Press the number buttons to enter the remaining CH number You cannot enter CC numbers When the COUNTRY setting is IRELAND Press the V A buttons to choose CH or CC then enter the remaining CH or CC number The TV shifts to registration mode When the registration is completed the picture of the TV channel appears on the screen The CH CC number is a number given to each broadcast frequency that carries a TV channel If the TV cannot detect the TV channel corresponding to the broadcast frequency indicated by the CH CC number a no signal
7. pictures CSI seri D0058 EN When set to 2 pictures multi you can view a TV picture and a picture from an external device You can not view a TV picture on more than one screen at the same time When 12 pictures multi is set pictures from external devices are not displayed When set to 2 pictures multi the main picture can be changed by pressing the P V A buttons The sub picture screen can be changed by pressing the V A buttons When set to 12 pictures multi and there are more than 12 pictures the next or previous 12 screens can be displayed by pressing the V A buttons F T L O 9 Changing the sub picture Displaying the next or previous 12 screens TOP MENU e When set to 2 pictures multi press the A swap button to switch the main picture and sub picture e 2 pictures multi function does not work for a picture of 11251 signal A picture of 625p or 525p signal cannot be displayed as the sub picture Pay attention to the following When the EXT 4 picture is a picture of 625p or 525p signal you cannot choose EXT 4 with the V A buttons When the EXT 4 picture signal 1s changed to 625p 525p or 11251 signal while the EXT 4 picture 15 displayed as the sub picture the 2 pictures multi function is cancelled The pictures cannot be swapped when a picture of 625p or 525p signal from EXT 4 is being displayed as the main picture Do not press the 73 swap button while you are recording
8. 2 8 210 0 DOS 7 8 9 Teletext function 3 Press and hold down the gt Store button The four page numbers blink white to show that they are stored in memory B To call up a stored page 1 Press the F T L button to enter the List mode 2 Press a colour button having a stored page zoo 2 2 O O QIO To exit the List mode Press the F T L button again Hold You can hold a teletext page on the screen for as long as you want even while several other teletext pages are being received Press the 3 Hold button Hold indication 102 103 To cancel the Hold function Press Hold button again Sub page Some teletext pages include sub pages that are automatically displayed 1 Choose a teletext page that includes sub pages Sub page numbers that can be viewed are automatically displayed at the top of the screen 2 Press the lt gt buttons to choose sub page number Reveal Some teletext pages include hidden text such as answers to a quiz You can display the hidden text Each time you press the Reveal button text is hidden or revealed 1 2 2 3 3 6 100 101 102 103 100 101 103 Size You can double the height of the teletext display Press the 3 Size button Index You can return to the index page instantly Press the Index button Returns to page 100 or a previously specified pa
9. Coaxial Cable Back of the TV AREE Era 21 pin SCART Cable pa Input Ae ap Terminal HV 32P37SJE HV 28P37SJE Aeri erial 75 ohm Coaxial A To Aerial Output Terminal Setting up your TV B Rear Panel HV 36P38SJE D Aerial socket page 5 2 Woofer terminal pages 7 3 EXT 1 terminal pages 5 39 42 4 EXT 2 terminal pages 5 12 39 42 5 EXT 3 terminal pages 39 42 6 EXT 4 terminal pages 39 42 7 AUDIO OUT terminal page 44 HV 32P37SJE HV 28P37SJE D Aerial socket page 5 2 EXT 1 terminal pages 5 39 42 3 EXT 2 terminal pages 5 12 39 42 4 EXT 3 terminal pages 39 42 5 EXT 4 terminal pages 39 42 6 AUDIO OUT terminal page 44 Setting up your TV Connecting and placing the woofer unit HV 36P38SJE only Connect the supplied woofer connector to the woofer terminal on the back of the TV If the woofer unit is not connected you will not be able to enjoy the bass sound Connect so that the lever is raised Lever When disconnecting the woofer connector do so while pushing the lever B Placing the woofer unit As shown in the diagram fix the supplied stoppers to the four corners of the side of the woofer unit that will be used as the base The woofer unit can be used either standing up or lying down There is no difference between the top and bottom of the wo
10. H EG ET CH 10 E10 IR H CH 48 E48 6 Press the OK button and register EH SEDENS iis iuis CH 12 E12 CH 50 E50 the TV channel to a Programme ES SHE Eri number PR CH22 E22 52 52 23 23 53 E53 The normal EDIT menu 15 resumed a CH 25 E25 CH 55 E55 E CH CC NUMBER CH 26 E26 CH 56 E56 e When you want to use the INSERT ener EM CH 28 E28 CH 58 E58 function on page 36 find the CH CC mE ES P number corresponding to the channel CH 30 E30 CH 60 E60 number of the TV channel from this table one ES Su 32 2 62 E62 If you want to know a particular TV mE ES channel s channel menu look in TV CH 34 E34 CH 64 E64 listings magazines or contact the aie n EOS b d t CH 36 E36 CH 66 E66 roadcaster CH 37 E37 CH 67 E67 When the COUNTRY setting is UNITED CH 38 E38 CH 68 E68 KINGDOM the CC number channels and EN E the channels from 02 to 12 Channel Channel CC 01 51 CC 31 31 cannot be received aaa S CC 03 S3 CC 33 S33 CC 04 S4 CC 34 S34 CC 05 S5 CC 35 S35 CC 06 S6 CC 36 S36 CC 07 S7 CC 37 537 CC 08 S8 CC 38 S38 CC 09 S9 CC 39 S39 CC 10 10 CC 40 S40 CC 11 11 CC 41 S41 CC 12 12 CC 75 X CC 13 13 CC 76 Y CC 14 14 CC 77 Z CC 15 15 CC 78 1 16 16 CC 79 2 2 17 517 18 518 19 519 20 520 21 21 CC 22 22 CC 23 23 CC 24 524 25 525 26 526 CC 27 S27 CC 28 28 CC 29 29
11. K L system A2 B G D K system Teletext systems FLOF Fastext FLOF Fastext TOP WST World Standard System WST World Standard System Power requirements 220 240 V AC 50 Hz Power consumption 141 W Standby 2 0 W Picture tube size Viewable area 86 cm measured diagonally Audio output Rated Power output TV 10 W 10 W Woofer 18 W Speakers TV 2 cm round x 2 3 cm x 10 cm oval x 4 Woofer 16 cm round x 1 EXT 1 terminal Euroconnector 21 pin SCART Video input Audio L R inputs and RGB inputs are available TV broadcast outputs Video and Audio L R are available EXT 2 terminal Euroconnector 21 pin SCART Video input S VIDEO Y C input Audio L R inputs and RGB inputs are available Video and Audio L R outputs are available T V LINK functions are available EXT 3 terminal Euroconnector 21 pin SCART Video input S VIDEO Y C input and Audio L R inputs are available EXT 4 terminal RCA connectors x 5 Component video Pr Pb Y inputs 625p 525p 1125i and Audio L R inputs are available EXT 5 terminal RCA connectors x 3 S VIDEO connector x 1 Video input S VIDEO Y C input and Audio L R inputs are available AUDIO OUT terminal RCA connectors x 2 Audio L R outputs are available Output level 0 5 Vrms Headphone jack Stereo mini jack 3 5 mm in diameter Dimensions W x H x D TV 912 mm x 624 mm x 593 mm Woofer 435 mm x 230 mm x 120 mm Weight TV 70 kg Woofer 4 kg Accessories
12. exit from the menu Types of menu PICTURE menu Choose to set the screen settings 0 SOUND menu w Choose to set the sound settings RID FEATURES menu mari Choose to set the sleep timer i and child lock settings ____ SET UP menu io Choose to edit the channels or A the display language settings The menu guide area can be made to appear and disappear for some menus While the menu is displayed press the button to change between the guide area being displayed and not displayed gt gt 4 3 AUTO ASPECT PANORAMIC REGULAR 14 9 ZOOM D0017 EN Guide area gt gt 4 3 AUTO ASPECT PANORAMIC k REGULAR 14 9 ZOOM D1017 EN e The guide area for some menus will still be displayed even if the W button is pressed This is not a fault 25 PICTURE menu PICTURE PICTURE MODE lt STANDARD_ p CONTRAST BRIGHT SHARP COLOUR HUE COLOUR TEMP FEATURES RESET eooo D0014 EN While the PICTURE menu is displayed pressing the blue button will set the CONTRAST BRIGHT SHARP COLOUR HUE settings to their default settings PICTURE MODE You can choose one of three PICTURE to adjust the picture settings automatically BRIGHT Heightens contrast and sharpness STANDARD Standardizes picture adjustment SOFT Softens contrast and sharpness CONTRAST You can adjust the picture contrast 4 low
13. image such as a white dress is displayed on the screen the white part may look as if it 1s coloured This is unavoidable due to the nature of the picture tube itself and not due to a TV failure When the picture disappears from the screen the unnatural colours will also disappear 45 46 Troubleshooting When viewing images from commercially available video software products or videos from videotapes which have been recorded improperly the top of the image may be distorted This is due to the condition of the video signal There is nothing wrong with the TV Since this TV is designed to make full use of the resolution of the original video source the motion may appear unnatural when the video source is input with 625p progressive scanning component signals If this occurs change the output setting of the connected device to 6251 interlace scanning component signal output See the instructions that came with the device for more information B Poor sound Have you adjusted BASS or TREBLE properly If not follow the description BASS or TREBLE on page 30 When TV channel reception is poor it can be hard to hear stereo or bilingual sound In this case follow the description STEREO I on page 30 to hear the sound more easily by changing it to a mono sound B If the TV does not respond to the remote control Have the batteries of the remote control worn out Follow the description Pu
14. infringement of copyright 2003 VICTOR COMPANY OF JAPAN LIMITED LCT1536 001A U 0903 T CR JMUK VICTOR COMPANY OF JAPAN LIMITED
15. manually The preset download function automatically begins when the initial setting is complete or whenever you carry out the AUTO PROGRAM or EDIT MANUAL functions You can also carry out this function using your VCR controls When FEATURE NOT AVAILABLE is displayed If FEATURE NOT AVAILABLE is displayed the download was not performed correctly Before trying to download again check that the VCR power is turned on the VCR is T V LINK compatible the VCR is connected to the EXT 2 terminal the SCART cable is fully wired You can easily record to VCR the images that you are watching on the TV For details read the manual for your VCR Use your VCR controls VCR IS RECORDING is displayed In the following situations the VCR will stop recording if the TV is turned off if the TV channel or input is changed or if the menu is displayed on the TV when recording images from an external device connected to the TV for example a camcorder when recording a TV channel after it has been unscrambled on a decoder when recording a TV channel by using the TV s output because the VCR s own tuner cannot properly receive that channel When the VCR is not ready for example when there is no tape inserted NO RECORDING is displayed You cannot carry out Direct Rec using your TV s control Generally the VCR cannot record a TV channel that it cannot receive properly on its own tuner even if
16. signal source to be output from the EXT 2 terminal You can do this with the output signals of the devices connected to other EXT terminals or with the picture and sound from a TV channel you are currently viewing 1 Press the lt gt buttons to choose the arrow from the menu Gh gt ext SETTING EXT 1 n NG EXT 3 EXT 5 EXT 4 am D0022 EN 2 Press the V A buttons to choose an EXT terminal or TV Then press the OK button The arrow in the menu represents a signal flow The left side of the arrow shows a signal source output from the EXT 2 terminal EXT 1 EXT 3 EXT 5 The output signal of the device connected to an EXT terminal passes through the TV and is output from the EXT 2 terminal SET UP menu TV The picture and sound of the TV channel you are currently viewing are output from the EXT 2 terminal During dubbing you cannot turn off the TV Turning off the TV also turns off the output from the EXT 2 terminal When you choose an EXT terminal as an output you can view a TV programme or a picture from the other EXT terminal while dubbing the picture from a device connected to the EXT terminal onto a VCR connected to the EXT 2 terminal The RGB signals from TV games cannot be output Teletext programmes cannot be output 41 Additional preparation Connecting external equipment Connect the equipment to the TV making the correct rear panel and front pane
17. stereo sound MONO Choose to add the 3D CINEMA SOUND effect to mono sound OFF Choose to cancel the 3D CINEMA SOUND effect The 3D CINEMA SOUND effect can be adjusted with the 3D CINEMA SOUND menu see page 30 Return to TV channel instantly You can return to a TV channel instantly Press the TV button The TV returns to the TV mode and a TV channel appears Using the FREEZE function You can view the current programme as a still picture 1 Press the button The still picture of the current picture will appear current programme still picture D0056 EN 19 20 Remote control buttons and functions To cancel the FREEZE function Press the C3 button the V A buttons or the number buttons The FREEZE function does not work while a sub picture is displayed The still picture cannot be output from the TV The FREEZE function does not work for pictures of 625p 525p and 11251 signals Using the MULTI PICTURE function 1 Press the C button The MULTI PICTURE menu appears 1 D0101 EN 2 Press the lt gt buttons to choose the number of screens and then press the OK button 1 Choose to return to one screen D0102 2 Choose to change to 2 pictures multi D0103 12 Choose to change to 12 pictures multi D0104 2 pictures multi Main Sub picture picture D0056 EN 12 pictures multi DL JL JE UE AI sut
18. the TV output on the VCR If you do the TV output signal will change You cannot view a scrambled channel in the sub picture If the A swap button is pressed when viewing a scrambled channel in the main picture using an external decoder the channel you have been viewing in the sub picture will appear in both the main picture and sub picture When set to 2 pictures multi and the headphones are connected the sound for the main picture 16 output from the TV speakers and the sound from the sub picture is output from the headphones Adjust the volume of the sub picture sound from the headphones with HEADPHONE VOLUME in the SOUND menu see page 30 The main picture sound can not be heard through the headphones When set to 12 pictures multi press the lt P V A buttons to choose the screen you want to view and the press the OK button to display that picture on the whole screen The BLUE BACK function does not work when the MULTI PICTURE function 15 being used The ZOOM function does not work when the MULTI PICTURE function is being used To return the multi picture to one screen Press the MULTI button press the lt gt buttons to choose one screen and then press the OK button Pressing the T V button will also return the display to one screen Remote control buttons and functions Operating a JVC brand VCR or DVD player These buttons will operate a JVC brand VCR or DVD pl
19. the programme number PR 0 AV manually For details see EDIT MANUAL on page 33 Pressing the AV button changes the choice as EX 5 4 Ioas S TV mode EXT modes Youcan choose a video input signal Programme gt PRO EXT EXT 2 from the S VIDEO signal Y C signal PR1 PR99 E2 Jor and regular video signal composite l Eu signal For details see S IN S MEIN NUS VIDEO input on page 39 e f you do not have a clear picture or no colour appears change the colour system manually See COLOUR Eg ee SYSTEM on page 28 e If you choose an EXT terminal with no input signal the EXT terminal number becomes fixed on the screen DA 2 4 The VCR sends its playback image along the aerial cable as an RF radio frequency signal Also see your VCR instruction manual 16 Remote control buttons and functions Adjust the volume Press the lt 1 buttons to adjust the volume The volume indicator appears and the volume changes as you press lt 1 buttons B Muting the sound Press the amp muting button to turn off the sound Pressing the amp muting button again restores the previous volume level Information function You can see the channel number of the programme you are watching the current time or the PR LIST From the PR LIST you can choose a channel or EXT terminal Press the 1 Information button to display th
20. you can use the CHILD LOCK function to lock out the TV channel Even when a child chooses a programme number PR for a locked TV channel the screen will change to blue and display d CHILD LOCK so the TV channel cannot be viewed Unless you enter a pre set ID number by a special operation the lock cannot be released and the child cannot view the TV channel B To set the CHILD LOCK function 1 Choose CHILD LOCK then press the 0 button SET ID NO ID number setting screen appears Ll SETID NO O 0040 D0025 EN 2 Setthe ID number to your liking 1 Press the V A buttons to choose a number 2 Press the 4 5 buttons to move the cursor 3 Press the OK button The Sub menu of CHILD LOCK appears ELN CHILD LOCK PR AV D0026 EK 32 FEATURES menu 4 Press the V A buttons to choose a TV channel Every time you press the W A buttons the Programme number PR changes and the picture of the TV channel registered in the Programme number PR is displayed on the screen Press the blue button and set the CHILD LOCK function Then press the OK button CHILD LOCK appears and the TV channel is locked To reset the CHILD LOCK function Press the blue button again CHILD LOCK disappears To disable easy resetting of the CHILD LOCK function the menu disappears if you choose the CHILD LOCK function and press the OK button B To view a locked TV channel 1 Choose a
21. you can view that TV channel on the TV However some VCRs can record a TV channel by using the TV s output if that channel can be viewed on the TV For details see your VCR instruction manual TV buttons and functions HV 36P38SJE See the pages in parentheses for details 1 Remote control sensor 2 Power lamp pages 8 14 3 Main power button pages 8 14 4 Headphone jack mini jack page 42 5 P V A buttons buttons page 14 1 Volume button page 14 7 EXT 5 terminal pages 39 42 HV 32P37SJE HV 28P37SJE See the pages in parentheses for details D Remote control sensor 2 Power lamp pages 8 14 3 Main power button pages 8 14 4 Headphone jack mini jack page 42 5 P V A buttons 4 buttons page 14 22 Volume button page 14 7 EXT 5 terminal pages 39 42 13 TV buttons and functions Turn the main power on Press the main power button on the TV The power lamp lights red and your TV is in standby mode Ifthe power lamp lights green the TV 15 already on To turn the main power off Press the main power button again The power lamp goes off Caution The main power button on the TV does not fully isolate the TV from the AC supply If you are not going to use the TV for a long period be sure to disconnec
22. DECODERY EXE2 etie caussis 38 EXT 2 2 39 Additional preparation 42 Connecting external equipment 42 Troubleshooting 45 47 Setting up your TV Caution e Turn off all the equipment including the TV before connecting anything Connecting the aerial and video cassette recorder VCR The connecting cables are not provided For further details refer to the manuals provided with the devices to be connected B If you are connecting a VCR follow gt B gt in the diagram opposite B If you are not connecting a VCR follow D To use the T V LINK functions you must have a T V LINK compatible VCR connected by a SCART cable O to the EXT 2 terminal on the TV For details about T V LINK functions see T V LINK functions on page 12 Youcan watch a video using the VCR without doing For details see your VCR instruction manual To connect more equipment please see Connecting external equipment on page 42 To connect additional audio equipment see Connecting speakers amplifier on page 44 f you connect a decoder to a T V LINK compatible VCR set the DECODER EXT 2 function to ON For details see DECODER EXT 2 on page 38 Otherwise you will not be able to watch scrambled channels HV 36P38SJE Aerial 75 ohm
23. DigiPure function is turned off MOVIE THEATRE The MOVIE THEATRE function displays a cinema film picture more smoothly and naturally on the screen AUTO The television automatically recognizes the type of signal and turns the function on and off ON This function is turned on OFF This function is turned off The motion may appear unnatural when viewing images with the NTSC colour system When the MOVIE THEATRE function is set to AUTO or ON the motion may appear unnatural when viewing images with the NTSC colour system Colour DigiPure Makes the colour outline stand out and increases the sharpness giving a clearer picture ON Colour DigiPure works Normally use with this function turned on OFF Colour DigiPure doesn t work This gives a less clear picture than when this function is turned on COLOUR SYSTEM The colour system is chosen automatically However if the picture is not clear or no colour appears choose the colour system manually 1 Choose COLOUR SYSTEM Then press the OK button The sub menu of the COLOUR SYSTEM function appears gt gt COLOUR SYSTEM D0016 EN 2 Press the lt gt buttons to choose MAIN or SUB MAIN You can change the colour system of the main picture SUB You can change the colour system of the sub picture Choose MAIN when a sub picture is not displayed 3 Press the V A buttons to choose the appropriate colour system
24. ITALIA SVERIGE ESPANA OSTERREICH NEDERLAND NORGE BELGIUM SUOMI START CZ CJ Y AN 000 ES e MORE 6 gt COUNTRY LUXEMBOUR PORTUGAL POLSKA CESK REP MAGYARO RUSSIA RUMANIA GREECE D0003 EN Setting up your TV 4 Press the 4 gt and V A buttons to choose the country where you are To receive SKY 1 you need a satellite tuner You must have the satellite tuner set to SKY 1 before starting the AUTO PROGRAM function which follows 5 Press the blue button to start the AUTO PROGRAM function The AUTO PROGRAM menu appears and received TV channels are automatically stored in the programme numbers PR lo gt gt AUTO PROGRAM Perform the ACI function operation see page 10 when ACI START ACI SKIP is displayed To cancel the AUTO PROGRAM function Press the T V button After the TV channels have been registered in the programme numbers PR the EDIT menu appears D0038 EK If you want to you can now edit the programme numbers PR using the EDIT MANUAL function For details see EDIT MANUAL on page 33 f you do not want to edit programme numbers PR go to the next step 10 Setting up your TV 6 Press the OK button to display the T V LINK menu DOWNLOAD TV gt VCR D0005 EN If you do not have a T V LINK compatible VCR connected Press the T V button to exit the T V LINK menu The T V LINK menu
25. LIST instruction manual You can have a name for each of the devices connected for each EXT terminal DUBBING You can choose a signal source to be output from an EXT 2 terminal B S IN S VIDEO input You can connect a device such as an S VHS VCR to enjoy the high quality picture of the S VIDEO signal Y C signal Preparation First read the device s instruction manual and Additional preparation on page 42 to connect the device to the TV properly Second follow the device s instruction manual to set the device so that it sends an S VIDEO signal Y C signal to the TV Do not set S IN S VIDEO input to an EXT terminal connected to a device which cannot output an S VIDEO Y C signal If it is set wrongly a picture cannot appear 39 40 SET UP menu 1 Press the lt P gt or V A buttons to choose an EXT terminal Gh gt ExT SETTING EXT 1 NG EXT 3 EXT 5 QOOO EXT 4 D0110 EN 2 Press the yellow button and set the S IN S VIDEO input Then press the OK button An S IN S VIDEO input mark is displayed You can view an S VIDEO signal Y C signal instead of the regular video signal composite signal To cancel the S IN S VIDEO input setting Press the yellow button and turn off S IN S VIDEO input mark The regular video signal composite signal pictures are resumed The EXT 1 terminal does not support S VIDEO signal Y C signal and you can
26. My InteriArt HV 36P38SJE HV 32P37SJE HV 28P37SJE u T V LINK plain English approved by the word centre E Warning DO NOT cut off the mains plug from this equipment If the plug fitted 1s not suitable for the power points in your home or the cable is too short to reach a power point then obtain an appropriate safety approved extension lead or adaptor or consult your dealer If nonetheless the mains plug is cut off remove the fuse and dispose of the plug immediately to avoid a possible shock hazard by inadvertent connection to the mains supply If a new mains plug has to be fitted then follow the instruction given below Important Do not make any connection to the larger terminal which is marked with the letter E or by the safety earth symbol or coloured green or green and yellow The wires in the mains lead on this product are coloured in accordance with the following code Blue Neutral Brown Live Guidelines for safe operation As these colours may not correspond with the coloured marking identifying the terminals in your plug proceed as follows The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red When replacing the fuse use only a correctly rated approved type and always re fit the fuse cover If in dou
27. Remote control unit x 1 RM C1800 Woofer x 1 AA R6 dry cell battery x 2 We may change the design and specifications without notice Pictures displayed on the screen using this TV s ZOOM functions should not be shown for any commercial or demonstration purpose in public places cafes hotels etc without the consent of the owners of copyright of the original picture sources as this would be an infringement of copyright 47 Model COUNTRY setting Broadcasting systems Colour systems Channels and frequencies Sound multiplex systems Teletext systems Power requirements Power consumption Picture tube size Audio output Speakers EXT 1 terminal EXT 2 terminal EXT 3 terminal EXT 4 terminal EXT 5 terminal AUDIO OUT terminal Headphone jack Dimensions W x H x D Weight Accessories HV 32P37SJE HV 28P37SJE When the COUNTRY setting is When the COUNTRY setting is UNITED KINGDOM IRELAND CCIR I CCIR B G I D K L PAL PAL SECAM The EXT terminals also support the The EXT terminals also support the NTSC 3 58 4 43 MHz system NTSC 3 58 4 43 MHz system E21 E69 IR A J E2 E12 E21 E69 51 541 X 2 2 1 2 2 NICAM I system NICAM B G I D K L system A2 B G D K system FLOF Fastext FLOF Fastext TOP WST World Standard System WST World Standard System 220 240 V AC 50 Hz HV 32P37SJE 137 W Standby 2 0 W HV 28P37SJE 127 W Standby 2 0 W HV 32P37SJE Viewable ar
28. SURROUND Adjust the surround effect You can choose HIGH MID or LOW Choosing LOW will reduce the surround effect and choosing HIGH will increase the surround effect BASS BOOST Adjust the bass sound You can choose HIGH MID or LOW Choosing LOW will reduce the bass sound and choosing HIGH will increase the bass sound FEATURES menu FEATURES SLEEP TIMER CHILD LOCK APPEARANCE BLUE BACK D0023 EN SLEEP TIMER You can set the TV to automatically turn off after a set period of time 1 Choose SLEEP TIMER Then press the OK or gt button A Sub menu of the SLEEP TIMER function appears gt SLEEP TIMER D0024 EN 2 Press the lt P gt buttons to set the period of time Then press the OK button You can set the period of time for up to 120 minutes 2 hours in 10 minute steps One minute before the SLEEP TIMER function turns off the TV GOOD NIGHT appears The SLEEP TIMER function cannot be used to turn off the TV s main power When the SLEEP TIMER function is on you can display the sub menu of the SLEEP TIMER function again to confirm or change the remaining period of time of the SLEEP TIMER function Press the OK button to leave the menu after confirming or changing the remaining time To cancel the SLEEP TIMER function Press the lt button to set the period of time to OFF CHILD LOCK When there is a TV channel you do not want your children to watch
29. TV to automatically change to a blue screen and mute the sound if the signal is weak or absent or when there is no input from an external device ON This function 1s turned on OFF This function is turned off SET UP menu D0029 EN AUTO PROGRAM You can again perform the AUTO PROGRAM function TV channel automatic registration which was performed in the Initial settings page 8 To receive SKY 1 you need a satellite tuner You must have the satellite tuner set to SK Y 1 before starting the AUTO PROGRAM function 1 Choose AUTO PROGRAM then press the OK or gt button The COUNTRY menu appears as a sub menu of the AUTO PROGRAM function There are two COUNTRY menus Pressing the yellow button changes the COUNTRY menu as follows Gh gt COUNTRY UNITED KINGDOM DEUTSCHLAND IRELAND SWITZERLAND DANMARK SVERIGE OSTERREICH NEDERLAND NORGE BELGIUM SUOMI START LON eoo C3 c MORE 8 gt COUNTRY LUXEMBOURG PORTUGAL OLSKA CESKA REP RUMANIA START D0003 EN 2 Press the 4 5 and V A buttons to choose the country where you are 3 Perform steps 5 and 6 of the Initial settings page 9 EDIT MANUAL The EDIT MANUAL functions are divided into two types editing the current programme numbers PR EDIT functions and e manually storing a TV channel you want to view on a particular programme number PR MAN
30. UAL function Here are the details about these functions MOVE This function changes the programme number PR of a TV channel ID This function registers a channel name ID to a TV channel INSERT This function adds a new TV channel in the current programme numbers PR list by using the CH number You cannot use the INSERT function if you do not know the channel number of a TV channel Use the MANUAL function to register a TV channel in the programme number PR DELETE This function deletes a TV channel you do not want to list MANUAL This function manually stores a new TV channel in a programme number PR Caution Using the MOVE DELETE or INSERT functions rewrites the current programme numbers PR list Therefore the programme numbers PR of some of the TV channels will change Using the MANUAL function for a TV channel for which the CHILD LOCK function has been set cancels the CHILD LOCK function for that channel Using the MANUAL function for a TV channel for which the DECODER EXT 2 function has been set to ON returns the setting of the DECODER EXT 2 function for that channel to OFF When a TV channel has already been registered in PR 99 using the INSERT function deletes that TV channel 33 34 SET UP menu B Basic operation 1 Choose EDIT MANUAL then press the OK button The EDIT menu appears MANUAL Y D0038 EK 2 Follow the description for t
31. added to produce a sharper more detailed picture You can choose from the three DigiPure function settings of AUTO MIN and MAX f you set the DigiPure effect too high on a low quality picture that contains a lot of noise this may actually make the noise worse We recommend you use the AUTO setting if you can Picture motion compensation function This function displays fast moving pictures for example the players or ball in a football game more smoothly and naturally on the screen The effect level of the picture motion compensation function cannot be changed The effect level is the same no matter which of the AUTO MIN or MAX settings is used AUTO The TV will automatically adjust the level of the DigiPure effect to match the amount of noise in the picture giving the best possible picture 27 28 PICTURE menu MIN The level of DigiPure effect is set to the minimum When you set the Super DigiPure function to AUTO and notice some noise change the setting from AUTO to MIN The MIN setting is not suitable for high quality pictures which contain very little noise MAX The level of DigiPure effect is set to the maximum If you set the Super DigiPure function to AUTO but feel that the original picture quality has not been reproduced fully change the setting from AUTO to MAX The MAX setting is not suitable for low quality pictures which contain a lot of noise OFF The Super
32. atio of the picture is included in the broadcast signal or the signal from an external device the TV automatically changes the ZOOM mode to 16 9 ZOOM mode or FULL mode according to the WSS signal Ifa WSS signal is not included the picture is displayed according to the ZOOM mode set with the 4 3 AUTO ASPECT function For details of the 4 3 AUTO ASPECT function see 4 3 AUTO ASPECT on page 29 When the AUTO WSS mode does not function correctly due to poor WSS signal quality or when you want to change the ZOOM mode press the ZOOM button and change to another ZOOM mode REGULAR Use to view a normal picture 4 3 aspect ratio as this is its original shape Or LO ONO ONO PANORAMIC This stretches the left and right sides of a normal picture 4 3 aspect ratio to fill the screen without making the picture appear unnatural O O O e The top and bottom of the picture are slightly cut off 14 9 ZOOM This zooms up the wide picture 14 9 aspect ratio to the upper and lower limits of the screen OO ON O 16 9 ZOOM This zooms up the wide picture 16 9 aspect ratio to the full screen LOHOO 16 9 ZOOM SUBTITLE This zooms up the wide picture 16 9 aspect ratio with subtitles to the full screen COLO FULL This uniformly stretches the left and right sides of a normal picture 4 3 aspect ratio to fill the wide TV screen
33. ay damage your hearing Never obstruct the ventilation of this equipment Doing so may cause overheating and result in a malfunction or damage Never use makeshift stands or attempt to affix legs with wood screws When using a manufacturer s approved stand or legs use only the fixtures provided and follow the installation instructions Never allow this equipment to be exposed to rain or moisture Never allow anyone especially children to insert anything into an opening in the case Doing so may result in a fatal electrical shock Never guess or take chances with electrical equipment of any kind It is better to be safe than sorry Thank you for buying this JVC colour television To make sure you understand how to use your new TV please read this manual thoroughly before you begin WARNING TO PREVENT FIRE OR SHOCK HAZARD DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE CAUTION e Operate only from the power source specified The main power button on the TV does not AC 220 240 V 50 Hz on the unit fully isolate the TV from the mains supply If Avoid damaging the AC plug and power cord you are not going to use this TV for a long When you are not using this unit for a long period of time be sure to disconnect the mains period of time it is recommended that you plug from the mains outlet disconnect the power cord from the main outlet Avoid improper installation and never put the unit where good ventila
34. ayed only HEADPHONE VOLUME can be used STEREO 1 Il When you are viewing a bilingual broadcast programme you can choose the sound from Bilingual I Sub I or Bilingual II Sub II If you have poor reception on a stereo broadcast you can change from stereo to mono sound so that you can hear the broadcast more clearly and easily CO Stereo sound O mono sound I Bilingual I sub I I Bilingual II sub The sound mode you can choose differs depending on the TV programme This function does not work in the EXT modes BASS You can adjust the low tone of the sound 4 weaker gt strong TREBLE You can adjust the high tone of the sound 4 weaker gt strong BALANCE You can adjust the volume balance between the left and right speaker lt turn the left speaker s volume level up gt turn the right speaker s volume level up HEADPHONE VOLUME Adjust the volume of the sub picture sound which is heard through the headphones when set to 2 pictures multi 4 Reduce volume gt Increase volume When not set to 2 pictures multi the headphone volume is adjusted with the lt 1 volume buttons 3D CINEMA SOUND Press the 3D button to set the 3D CINEMA SOUND effect when 3D CINEMA SOUND is set to ON or MONO Choose 3D CINEMA SOUND Then press the OK or gt button to display the sub menu i gt 3D CINEMA souND SURROUND BASS BOOST D0111 EN
35. ayer Pressing a button that looks the same as the device s original remote control button has the same effect as the original remote control 1 Set the VCR TV DVD Switch to the VCR or DVD position VCR When you are operating the VCR set the switch to the VCR position Youcan turn the VCR on or off with the standby button DVD When you are operating the DVD player set the switch to the DVD position Youcan turn the DVD player on or off with the standby button 2 Press the VCR DVD Control Button to control your VCR or DVD player f your device is not made by JVC these buttons will not work Even if your device is made by JVC some of these buttons may not work depending on the device you are using e You can use the V A buttons to choose a TV channel the VCR will receive or choose the chapter the DVD player plays back Some models of DVD player use the V A buttons for both operating the fast forward backward functions and for choosing the chapter In this case the 44 buttons do not work You cannot turn the TV on or off when the VCR TV DVD switch is set to the VCR or DVD position When you turn the TV on or off set the VCR TV DVD switch to the TV position 21 Teletext function As IKO ob 3 MI 24 op VCR TV DVD Basic operation You can view three types of teletext broadcasts on the TV FLOF Fastext TOP and WST TOP is not available when th
36. bt consult a competent electrician How to replace the fuse Open the fuse compartment with a id blade screwdriver and replace the fuse This equipment has been designed and manufactured to comply with international safety standards However as with any electrical appliance care must be taken to ensure optimal results and operational safety Before attempting to use this equipment read the operating instructions thoroughly Ensure that all electrical connections including the mains plug extension leads etc have been made in accordance with the manufacturer s instructions fever in doubt about the installation operation or safety of this equipment consult your dealer Handle all glass panels or covers with care Never operate this equipment if it appears damaged or operates abnormally Turn the power off disconnect the main power plug and consult your dealer Never remove any affixed panels or covers Doing so may result in electrical shock Never leave this equipment operating unattended unless otherwise specifically stated that it 1s designed to do so or in standby mode Only use the designated power switch to turn off the power and ensure that all potential users are instructed how to do so Make special arrangements for infirm or handicapped persons Never watch TV while operating a motor vehicle It is illegal to watch TV while driving Never listen to headphones at high volume Doing so m
37. buttons and functions This TV set has a function which can Choose a TV channel and automatically change over the input watch images from external according to a special signal output devices from an external device The EXT 4 and EXT 5 terminals do not support If the picture is tilted correct it See this function PICTURE TILT on page 38 Since this TV is designed to make full B Use the number buttons use of the resolution of the original video source the motion may appear unnatural when the video source is input with 625p progressive scanning Enter the programme number PR of the channel using the number buttons component signals Example If this happens change the output e PR 6 press 6 setting of the connected device to 6251 PR 12 press 1 and 2 interlace scanning component signal output See the instructions that came with the device for more information Use the P V A buttons Press the P V A buttons to choose the programme number PR you want or an EXT terminal B Use the AV button To return to a TV channel Press the T V button the W A buttons or the number buttons To use the programme number PR 0 Press the AV button to choose an AV EXT terminal When the TV and VCR are connected only TV mode EXT modes by the aerial cable choosing the programme number PR 0 AV allows you to view QQumbers gt _ 1 2 images from the VCR Set the VCR RF channel to
38. cture may be tilted due to the earth s magnetic field If so use the PICTURE TILT on page 38 to correct the tilt It takes a short period of time from the time an operation such as changing channels is performed until an image is displayed This is not a fault This is the time needed for the image to stabilize before it can be displayed The TV may make a crackling sound due to a sudden change in temperature The picture or sound may be normal If you hear crackling sounds frequently while you are viewing the TV there may be other causes As a precaution ask your service technician to inspect it Touching the screen may cause you to feel a slight electric shock due to its static electricity This is unavoidable due to the construction of the picture tube It is not a problem with the TV You can rest assured that this static discharge is not harmful When set to 2 pictures multi adjust the headphone sound with HEADPHONE VOLUME in the SOUND menu Specifications Model HV 36P38SJE COUNTRY setting When the COUNTRY setting is When the COUNTRY setting is UNITED KINGDOM IRELAND Broadcasting systems CCIR CCIR B G I D K L Colour systems PAL PAL SECAM The EXT terminals also support the The EXT terminals also support the NTSC 3 58 4 43 MHz system NTSC 3 58 4 43 MHz system Channels and frequencies E21 E69 IR A J E2 E12 E21 E69 S1 S41 X Y Z Z 1 Z 2 Sound multiplex systems NICAM system NICAM B G I D
39. disappears If you have a T V LINK compatible VCR connected to the EXT 2 terminal Follow the operating procedure Downloading the data to VCR on page 11 to transmit the Programme number PR data Now the initial settings are complete and you can watch the TV When the COUNTRY setting is UNITED KINGDOM BBC2 ITV Channel 4 and Channel 5 are automatically set to the programme numbers to PRS If the TV doesn t receive one of these TV channels that programme number PR will not be set Programme number PR6 is not normally set When the COUNTRY setting is IRELAND If your TV can detect the TV channel name from the TV channel broadcast signal the TV channel name is assigned to the programme number PR to which the TV channel has been set However which TV channels are set to which programme numbers PR will depend on the area in which you live fa TV channel you want to view is not set to a programme number PR you can set it using the MANUAL function For details see EDIT MANUAL on page 33 The AUTO PROGRAM function does not set the programme number PR 0 AV for your video cassette recorder You will need to set this using the MANUAL function n some areas you may get TV reception from more than one transmitter for example different ITV regions In this case each TV channel could be set twice If this happens the first set of channels will have the stronger signal I
40. e 21 Teletext function 22 Basic operation 22 Using the List Mode 22 Ute 23 SUD PAJE uu el 23 Reveal 23 TRU PUN UST 23 ieee 23 24 Using the TV s menu 25 Basic operation 25 PICTURE nr rii e lt lt 26 PICTURE 32 50e 26 CONTRAS et 26 BRIGH 26 n ead adeant 26 COLOUR idest NS 26 PUE E 26 COLOUR TEMP 26 SOUND 30 STEREO iie ta 30 BASS d rs a A ae 30 TREBLE esc xs nima m 30 BALANCE neue 30 HEADPHONE VOLUME 30 3D CINEMA 5 30 FEATURES menwu 31 SLEEP TIMER 31 MP qe 31 2 32 2 32 SETUP 33 AUTO 33 33 2 38 PICTURE ea oc eS 38
41. e COUNTRY setting is UNITED KINGDOM 1 Choose TV channel with a teletext broadcast 2 Set the VCR TV DVD switch to the TV position PA WU ONS VCR TV DVD u ee e 3 Press E Text button to display the teletext Pressing Text button changes the mode as follows PAREN Text mode 22 4 Choose teletext page by pressing the P V A buttons number buttons or colour buttons To return to the TV mode Press the T V button or Text button e If you have trouble receiving teletext broadcasts consult your local dealer or the teletext station The ZOOM function will not work in the TV and text mode or Text mode You cannot operate menus when viewing a teletext programme Language display depends on the country which was set on the COUNTRY menu If characters on a Teletext programme do not appear properly change the COUNTRY setting to other country s To change the COUNTRY setting perform steps 1 and 2 of the AUTO PROGRAM procedure on page 33 and then press the OK button Using the List Mode You can store the numbers of your favourite teletext pages in memory and call them up quickly using the colour buttons B To store the page numbers 1 Press F T L button to go into the List mode The page numbers you have stored are displayed at the bottom of the screen 2 Press a colour button to choose a position Then press the number buttons to enter the page number zoom 29 1
42. e information you want to see Pressing the Information button changes the display as follows PR LIST mm Channel number display i No indication D0011 EN Channel number display The channel number and channel name when the channel name is registered of the programme you are watching or the EXT terminal number is displayed Time display The current time of the teletext data 1s displayed If the TV has not received a TV channel that has teletext programmes since it was turned on the time display is blank To view the current time choose a TV channel that has teletext programmes The time will continue to be displayed until the TV is turned off even if you choose other TV channels An incorrect current time is sometimes displayed when watching videos PR LIST The programme number PR and EXT terminal list is displayed Pressing the OK button after choosing the programme number PR or EXT terminal with the lt P W A buttons will display the chosen programme or EXT terminal For programme numbers PR for which the CHILD LOCK function is set CHILD LOCK mark is displayed For details see CHILD LOCK on page 31 17 18 Remote control buttons and functions ZOOM function You can change the screen size according to the picture aspect ratio Choose the optimum one from the following ZOOM modes AUTO When a WSS Wide Screen Signalling signal which shows the aspect r
43. ea 76 cm measured diagonally HV 28P37SJE Viewable area 66 cm measured diagonally Rated Power output 10 W 10 W 13 cm x 6 5 cm oval x 2 Euroconnector 21 pin SCART Video input Audio L R inputs and RGB inputs are available TV broadcast outputs Video and Audio L R are available Euroconnector 21 pin SCART Video input S VIDEO Y C input Audio L R inputs and RGB inputs are available Video and Audio L R outputs are available T V LINK functions are available Euroconnector 21 pin SCART Video input S VIDEO Y C input and Audio L R inputs are available RCA connectors x 5 Component video Pr Pb Y inputs 625p 525p 1125i and Audio L R inputs are available RCA connectors x 3 S VIDEO connector x 1 Video input S VIDEO Y C input and Audio L R inputs are available RCA connectors x 2 Audio L R outputs are available Output level 0 5 Vrms Stereo mini jack 3 5 mm in diameter HV 32P37SJE 948 mm x 562 mm x 550 mm HV 28P37SJE 854 mm x 508 mm x 493 mm HV 32P37SJE 54 0 kg HV 28P37SJE 38 0 kg Remote control unit x 1 RM C1800 AA R6 dry cell battery x 2 We may change the design and specifications without notice Pictures displayed on the screen using this TV s ZOOM functions should not be shown for any commercial or demonstration purpose in public places cafes hotels etc without the consent of the owners of copyright of the original picture sources as this would be an
44. el you are viewing is always output from the EXT 1 terminal Changing over a programme number PR also changes over the TV output from the EXT 1 terminal The video sound signal from an EXT terminal cannot be output Teletext programmes cannot be output Connecting speakers amplifier While referring to the audio equipment connection diagram connect the audio equipment you want to the TV You can use external front speakers to listen to the TV sound instead of the TV speakers Before connecting anything Read the manuals provided with the amplifier and speakers Turn the TV and amplifier off To prevent magnetism from the speakers adversely effecting the TV screen use magnetic shielded speakers for the front speakers Note that connecting cables are not supplied Back of the TV L AUDIO OUT B Amplifier Front speakers Magnetic shielded type The output from the AUDIO OUT terminal is not interrupted by headphone connection to the TV You cannot cut the sound from the front speaker even if you connect a headphone to the TV Adjust the volume of the external speakers with the amplifier Troubleshooting If a problem arises while you are using the TV please read this troubleshooting guide carefully before you ask to have the TV repaired You may be able to fix it easily by yourself For example if the mains plug is di
45. er gt higher BRIGHT You can adjust the picture brightness 4 darker gt brighter SHARP You can adjust the picture sharpness 4 softer gt sharper 26 COLOUR You can adjust the picture colour lt lighter P deeper HUE You can adjust the picture tint lt reddish P greenish You can change the HUE setting picture hue when the colour system is NTSC 3 58 or NTSC 4 43 COLOUR TEMP You can select one of three COLOUR TEMP modes three tones of white to adjust the white balance of the picture Since white is the colour which is used as a reference for all the other colours changing the COLOUR TEMP mode affects the appearance of all the other colours on the screen COOL A bluish white Using this mode when watching bright pictures allows you to enjoy a more vivid and bright picture NORMAL The normal white colour WARM A reddish white Using this mode when watching films allows you to enjoy colours that are characteristic of films PICTURE menu FEATURES Choose FEATURES and press the OK button to display the sub menu DIGITAL VNR Super DigiPure MOVIE THEATRE Colour DigiPure COLOUR SYSTEM 4 3 AUTO ASPECT 4 AUTO LOW D1015 EN B DIGITAL VNR The DIGITAL VNR function cuts down the amount of noise snow or interference in the original picture You can choose from the three DIGITAL VNR function settings of AUTO MIN and MAX
46. ess the lt gt buttons to choose ON An unscrambled picture appears To cancel the DECODER EXT 2 function Press the lt buttons to choose OFF 5 Press the OK button to complete the setting The T V LINK menu appears T V LINK DOWNLOAD TV gt VCR D0005 EN You can send the programme numbers data to a VCR with the T V LINK function SET UP menu 6 Turn on the VCR and then press EXT SETTING the OK button to transmit the data to VCR The T V LINK menu disappears once the data transmission ends 1 Choose EXT SETTING then press the OK button The EXT SETTING menu appears 7 f you have another TV channel capable of being unscrambled with 0 gt ext SETTING a Decoder repeat steps 2 to 6 Zo 5222 22 22 3 If the DECODER 2 function has been set to but the TV channel cannot be unscrambled check the following Has the decoder been connected to the VCR properly according to the VCR and decoder instruction manuals D0020 EN Has the decoder power been turned on Can the TV channel be unscrambled with a decoder Do you need to change the VCR S IN settings in order to connect the You can enjoy the high quality picture of EXT 4 2 Follow the instructions for the function you want to use and operate the function decoder Confirm that the VCR is set the 2 S VIDEO signal Y C signal properly by rechecking the VCR ID
47. f you want to delete the second set of channels you will have to do it manually see page 33 For users in the UK If you have any problems setting up your new TV please call the JVC Helpline on 0870 330 5000 For users in the Republic of Ireland If you have any problems setting up your new TV please call the JVC Helpline on 1890 582500 B ACI function This TV has an ACI function which decodes the ACI Automatic Channel Installation data Using the ACI function allows all TV channels transmitted from the cable TV station to be properly registered quickly according to the data from the cable TV station If ACI START ACI SKIP appears in the AUTO PROGRAM menu You can use the ACI Automatic Channel Installation function to decode the ACI data and complete the registration of all the TV channels in a short period of time Press the V A buttons to choose ACI START Then press the OK button to start the ACI function Depending on your cable TV station there may be a broadcast selection menu set up by the cable TV station Follow the menu instructions and use the lt P gt and V A buttons to operate the menu After you have made the setting press the OK button If you have any questions about the items in the Broadcast Selection menu or how to operate the menu please contact your cable TV station If you don t want to use the ACI function press the W A buttons to choose ACI SKIP and then p
48. ge 23 24 Teletext function Cancel You can search for a teletext page while watching TV 1 Press the number button to enter a page number or press a colour button The TV searches for a teletext page Press C9 Cancel button The TV programme appears When the TV finds the teletext page its page number appears in the upper left of the screen Press X Cancel button to return to a teletext page when the page number is on the screen The TV mode cannot be resumed by pressing the GY Cancel button To return to the TV mode press T V Using the TV s menu This TV has a number of functions you can operate using menus To use all your TV s functions you need to understand the basic menu operating techniques fully Buttons used to operate the menus RIES LA CN V J lt gt V A Basic operation 1 Press the MENU button to display the menu bar m ga d D0105 EN PICTURE m d 2 Press the lt gt buttons to choose the menu you want to use and then press the OK button c m gg 9 eee D110 EN Chosen Chosen menu menu name 3 Press the V A buttons to choose the item to be set press the lt gt buttons to set the item and then press the OK button If there are sub menus use lt P W A buttons to operate them Press the BACK button to return to the previous menu Press the TV or MENU button to
49. he function you want to use 3 Press the OK button to complete the settings The T V LINK menu appears T V LINK DOWNLOAD TV gt VCR D0005 EN If you do not have a T V LINK compatible VCR connected Press the T V button to exit the T V LINK menu The T V LINK menu disappears If you have a T V LINK compatible VCR connected to the EXT 2 terminal Follow Downloading the data to VCR on page 11 to transmit the programme number PR data For programme number PR 0 AV appears in the programme numbers PR list An EXT terminal number does not appear in the programme numbers PR list The CH CC number is a number unique to the TV and corresponds to the channel number of a TV channel For the relationship between a channel number and a CH CC number see CH CC NUMBER on page 37 B MOVE 1 Press the V A buttons to choose TV channel Every time you press the W A buttons the programme number PR changes and the picture of the TV channel stored in the programme number PR appears on the screen Press the gt button to start the MOVE function BBC1 CH 21 D0030 EK Press the V A buttons to choose new programme number PR To cancel the MOVE function Press the BACK button Press the lt button to change the programme number PR of a TV channel to a new programme number PR SET UP menu E DELETE 4 Press the blue button to display the 1 Press the W A bu
50. l connections Before connecting anything Read the manuals that came with the equipment Depending on the equipment the connection method may be different from the diagram Also the equipment settings may need to change depending on the connection method Turn off all the equipment including the TV The Specifications on the back cover give the details of the EXT terminals If you are connecting equipment not listed in the following connection diagram see the table to choose the best EXT terminal Connecting cables are not supplied HV 36P38SJE Front of the TV D VCR composite signal 2 VCR composite signal S VIDEO signal 3 T V LINK compatible VCR composite signal S VIDEO signal 4 Decoder 5 DVD player composite signal S VIDEO signal 6 DVD player composite signal RGB signal 7 DVD player component video signals Pr Pb Y TV game composite signal RGB signal 9 TV game composite signal S VIDEO signal Headphones 17 Camcorder composite signal S VIDEO signal 2 SCART cable 3 Audio cable Video cable 5 S VIDEO cable Component cable 42 HV 32P37SJE HV 28P37SJE Back of the TV Additional preparation 43 Additional preparation B Equipment which can output the S VIDEO signal Y C sig
51. menu This new menu is operated from the VCR See the VCR instruction manual for what to do next If FEATURE NOT AVAILABLE appears at the T V LINK menu Check the following three items Then press the lt button to retry data transmission Hasa T V LINK compatible VCR been connected to the EXT 2 terminal Has the VCR power been turned on Does the SCART cable that is connected to the EXT 2 terminal to T V LINK compatible VCR have all its proper connections 11 Setting up your TV B Direct Rec T V LINK functions What You See Is What You Record 12 When you have a T V LINK compatible VCR connected to the EXT 2 Terminal on the TV it is easier to set up the VCR and to view videos T V LINK uses the following features To use T V LINK functions A T V LINK compatible VCR means a JVC video cassette recorder with the T V LINK logo or with one of the following logos However these VCRs may support some or all of the features described earlier For details see your VCR instruction manual Q LINK a trademark of Panasonic Corporation Data Logic a trademark of Metz Corporation Easy Link a trademark of Phillips Corporation Megalogic a trademark of Grundig Corporation SMARTLINK a trademark of Sony Corporation Pre set download The VCR will automatically download the registered data on the TV channels from the TV This means you do not need to set up the program channels on your VCR
52. nal such as an S VHS VCR Connect the equipment to an EXT terminal but not the EXT 1 terminal You can choose between an S VIDEO signal Y C signal and a regular video signal composite signal For details of how to operate the equipment see S IN S VIDEO input on page 39 T V LINK compatible VCR Be sure to connect the T V LINK compatible VCR to the EXT 2 terminal If not the T V LINK function will not work properly Whenconnecting a T V LINK compatible VCR to the EXT 2 terminal be sure to connect the decoder to the VCR If not the T V LINK function may not work properly After you have stored TV channels in the programme numbers PR list set the DECODER EXT 2 function for the programme number PR to ON to unscramble a scrambled TV channel For details see EXT SETTING on page 39 B Connecting headphones Connect the headphones with a stereo mini jack 3 5 mm diameter to the headphone socket at the TV rear panel No sound comes from the TV speakers when the headphones are connected and only one screen is displayed Video or sound signal output from the EXT 2 terminal You can change over the output of the video sound signal from the EXT 2 terminal This is useful when you want to dub the video sound from another device onto the VCR connected to the EXT 2 terminal For details on how to do this see DUBBING on page 41 TV output from the EXT 1 terminal The video sound signal of a TV chann
53. ngs 0 av 1 Yellow button TV O OVIG Blue button OK Y A buttons 1 Press the main power button on the TV The power lamp lights red for power on then green for TV on and the JVC logo appears HV 36P38SJE F Power lamp Main power button HV 32P37SJE HV 28P37SJE Power lamp Main power button Ifthe power lamp stays red and does not change to green Your TV is in the standby mode To turn the TV on set the VCR TV DVD switch on the remote control to the TV position and press the I button See page 15 Ifthe JVC logo does not appear this 15 because your TV has already been turned on for the first time use the LANGUAGE and AUTO PROGRAM functions to make the initial settings For details see SET UP menu on page 33 2 Press the OK button The LANGUAGE menu appears Gah gt LANGUAGE ENGLISH SVENSKA FRAN AIS SUOMI DEUTSCH POLSKI ITALIANO CESKY CASTELLANO MAGYAR NEDERLANDS DANSK NORSK D0002 E EN Press the W A buttons to choose ENGLISH Then press the OK button The on screen display will then be in English The COUNTRY menu appears as a sub menu of the AUTO PROGRAM function There are two COUNTRY menus Pressing the yellow button changes the COUNTRY menu as follows Gh gt COUNTRY UNITED KINGDOM IRELAND DEUTSCHLAND SWITZERLAND FRANCE DANMARK
54. not set S IN S VIDEO input in the EXT 1 terminal Setting S IN S VIDEO input changes the head character from E to S When an EXT terminal receives a normal video signal E1 E2 or E4 appears on the display This changes to 52 53 or S5 when it receives an S VIDEO signal Even a device which can output an S VIDEO signal Y C signal may output a regular video signal composite signal depending on the device setting If a picture cannot appear because the S IN S VIDEO input setting has been made read the device instruction manual carefully again to check for the device settings B ID LIST You can store a name for each of the devices connected to each EXT terminal Giving a name to an EXT terminal makes the EXT terminal number appear on the screen together with its name 1 Press the lt P gt or V A buttons to choose an EXT terminal 2 Press the blue button to display the name list ID LIST 8 gt ExT SETTING EXT 1 DUBBING ID LIST EXT 2 EXT 3 EXT 5 EXT 4 D0021 EN 3 Press the W A buttons to choose a name Then press the OK button The ID LIST disappears and the name 15 assigned to the EXT terminal You cannot assign an EXT terminal name not found in the name list ID LIST To erase a name assigned to the EXT terminal Choose a blank space 4 Press the OK button to complete the setting B DUBBING You can choose a
55. ofer unit irrespective of whether it is being used standing up or lying down Place the woofer unit within the range of the connection cable It is recommended that the woofer unit be placed with the speaker facing forwards Pay attention to the following in order to prevent unnatural colours from appearing in the corner of the screen Place the woofer unit at least 20 cm away from either side of the TV Do not place the woofer unit on top of the TV When the TV is used on a TV stand or table do not place the woofer unit underneath the TV Setting up your TV Connecting the power cord to the AC outlet Caution Operate only from the power source specified AC 220 240 V 50 Hz on the unit F Putting the batteries into the remote control Use two AA R6 dry cell batteries Insert the batteries from the end making sure the and polarities are correct Follow the warnings printed on the batteries Battery life is about six months to one year depending on how much you use the remote control The batteries we supply are only for setting up and testing your TV please replace them as soon as you need to If the remote control does not work properly replace the batteries Initial settings When the TV is first turned on it goes into the initial settings mode and you will see the JVC logo Follow the instructions on the screen display to make the initial setti
56. picture appears B MANUAL 1 Press the V A buttons to choose a programme number PR for a new TV channel Press the blue button to activate the MANUAL function 0 gt MANUAL SEARCH FINE e 9 oe SEARCH FINE D0035 EK To cancel the MANUAL function Press the BACK button When the COUNTRY setting is IRELAND At the right side following the CH CC number the SYSTEM broadcasting system of the TV channel appears When the COUNTRY setting is UNITED KINGDOM Continue to step 4 When the COUNTRY setting is IRELAND Press the gt button to choose the SYSTEM broadcasting system for a TV channel you want to register If you do not know the correct broadcasting system set the SYSTEM to P If T is not correct you will not hear the sound normally when the TV detects a TV channel In this case retry to set the SYSTEM correctly so that no problem arises Press the green or red button to search for a TV channel Scanning stops when the TV finds a TV channel Then the TV channel is displayed SET UP menu H Ch CH Ch 5 Press the green red button E icis 02 E2 IRA 40 40 repeatedly until the TV channel you CHO3 E3 RB CHA 1 want appears CH 04 E4 IRC CH 42 E42 3 05 E5 IRD CH 43 E43 If the TV channel reception is poor CH 06 E6 IRE CH44 E44 Press the blue or yellow button to fine CELINE ES CH 08 E8 IR G CH 46 E46 tune the TV channel
57. programme number PR of a locked TV channel with the number buttons or PR LIST The screen changes to blue and the CHILD LOCK appears You cannot view the TV channel late jJ D0027 EN Press the 1 Information button to display ID NO ID No input screen D0028 EN Press the number buttons to enter the ID number The lock is temporarily released so you can view the TV channel If you have forgotten the ID number Perform step 1 of To set the CHILD LOCK function After confirming the ID number press the T V button to exit the menu Even if you reset the lock temporarily it does not mean that the CHILD LOCK function set for the TV channel is cancelled The next time anyone tries to view the TV channel it will be locked again When you want to cancel the CHILD LOCK function you must perform the operation To set the CHILD LOCK function again To stop it being easy to choose the programme number PR of a locked TV channel the programme number PR has been set so that it cannot be chosen with the W A buttons or the buttons of the TV To stop it being easy to reset the lock ID NO ID No input screen is set so that it cannot appear unless you press the G Information button APPEARANCE Press the lt P button and choose the format in which the channel number is displayed from the three types TYPE A TYPE B and TYPE C BLUE BACK You can set the
58. ress OK When the cable TV broadcast reception is poor the ACI function will not work properly If there is an error in the ACI data itself the TV channel cannot be registered properly If this happens turn the ACI function off ACI SKIP and use the AUTO PROGRAM function Alternatively use the EDIT MANUAL function to correct the Programme number PR setting If ACI ERROR is displayed in the AUTO PROGRAM menu ACI ERROR means that the ACI function is not working properly Press the lt button to start the ACI function again If ACI ERROR still appears even after you have tried to start the ACI function several times press the button to start the AUTO PROGRAM function It does not cause any problem because all the TV channels are registered to the Programme numbers PR by the AUTO PROGRAM function Downloading the data to VCR You can transmit to the latest Programme numbers PR data to a VCR with the T V LINK function Caution This only works when a T V LINK compatible VCR is connected to the EXT 2 terminal This only works when the T V LINK menu is being displayed T V LINK DOWNLOAD TV gt VCR D0005 EN Setting up your TV 1 Turn on the VCR 2 Press the OK button The data transmission begins DOWNLOAD TV VCR D0037 EN The T V LINK menu disappears once the data transmission ends When the T V LINK menu is changed over to another menu The TV has finished its
59. sconnected from the mains outlet or the TV aerial has problems you may think there is a problem with the TV itself Important This troubleshooting guide only covers problems whose causes are not easy to decide If you have a question when you are operating a function read the page s for that function carefully not this troubleshooting guide If you follow the advice in this troubleshooting guide without any success unplug the mains plug and ask for your TV to be repaired Do not attempt to repair the TV by yourself or to remove the rear cover of the TV B If you cannot turn on the TV s the mains plug connected to the mains outlet s the power lamp lit If not press the main power button Make sure you set the VCR TV DVD switch to the TV position You cannot turn the TV on when the VCR TV DVD switch is set to the VCR or DVD position B If you cannot turn off the TV Make sure you set the VCR TV DVD switch to the TV position You cannot turn the TV off when the VCR TV DVD switch is set to the VCR or DVD position B No picture or no sound Have you chosen a TV channel with very poor reception If so the BLUE BACK function will be activated the entire screen becomes blue and the sound 15 muted If you still want to view the TV channel follow the description BLUE BACK on page 32 to change the BLUE BACK function setting to OFF Ifthe SYSTEM setting for a TV channel is incorrect it may pre
60. t the AC plug from the AC socket Turn the TV on from standby mode Press the P V A buttons to turn the TV on from standby mode Choose a TV channel Press the P V A buttons to choose a programme number PR or an EXT terminal Adjust the volume 1 Press the 21 Volume button The volume level indicator appears 2 Press the buttons while the volume level indicator is displayed Remote control buttons and functions Y eel D Muting button 2 Number buttons 9 Information button ZOOM button 5 sound button 6 TV button 7 lt gt V A buttons Text button 9 P V A buttons VCR DVD Teletext control buttons 17 V A buttons 2 Standby button 13 VCR TV DVD switch AV button 5 Colour button C Multi button 2 3 3 Freeze Swap button MENU button OK button 20 BACK button 0 1 Volume buttons Turn the TV on or off from standby mode Press the 0 1 standby button to turn the TV on or off When the TV is turned on the power lamp changes from red to green The power can be turned on by pressing the T V button P V A buttons or Number buttons To turn the TV on or off set the VCR TV DVD switch on the remote control to the TV position and press the I button If the VCR TV DVD switch on the remote control is set to a position other than TV the TV will not be turned on or off even if the button is pressed 15 Remote control
61. tion is not possible When installing this TV distance recommendations must be maintained between the set and the wall as well as inside a tightly enclosed area or piece of furniture Adhere to the minimum distance guidelines shown for safe operation Failure to heed the following precautions may result in damage to the TV or remote control DO NOT block the TV s ventilation openings or holes If the ventilation openings or holes are blocked by a newspaper or cloth etc the heat may not be able to get out DO NOT place anything on top of the TV such as cosmetics or medicines flower vases potted plants cups etc DO NOT allow objects or liquid into the cabinet openings If water or liquid is allowed to enter this equipment fire or electric shock may be caused DO NOT place any naked flame sources such as lighted candles on the TV The surface of the TV screen is easily damaged Be very careful with it when handling the TV Should the TV screen become soiled wipe it with a soft dry cloth Never rub it forcefully Never use any cleaner or detergent on it In the event of a fault unplug the unit and call a service technician Do not attempt to repair it yourself or remove the rear cover D I S T demonstration To start the D I S T demonstration Press the MENU button to display the menu bar Then press the yellow button A picture split in two D LS T turned on and D I S T turned off will appear on the screen
62. tting the batteries into the remote control on page 8 and replace them with new batteries Have you attempted to use the remote control from the sides or rear of the TV or from more than seven metres away from the TV Use the remote control in front of your TV or from less than seven metres away When you are viewing a teletext programme you cannot operate the menus Press the T V button to return to the ordinary TV programme and then try operating the menus If the TV suddenly stops responding press the main power button on the TV and turn off the main power Press the main power button again to turn on the TV If the TV returns to a normal state it is not a failure B Other issues When the SLEEP TIMER function operates the TV is automatically turned off If the TV suddenly turns off try to press the standby button to turn on the TV once again If the TV goes back to normal there is no problem When the TV is receiving a wide screen signal WSS or a signal from an external device affecting the screen size the ZOOM mode automatically changes When you want to resume the previous ZOOM mode press the ZOOM button again If you bring magnetised equipment such as a speaker near to your TV the picture may be warped or unnatural colours may appear at the corners of the screen In this case keep the equipment away from your TV If speakers cause this to happen use magnetically shielded speakers instead A pi
63. ttons to choose a ID LIST channel name list TV channel Every time you press the W A buttons the PR ID LIST Me programme number PR changes and the picture of the TV channel stored in the programme number PR appears on the screen 2 Press the yellow button to delete the TV channel The TV channel is deleted from the prog ramone ADS LER S 5 Press the V A buttons to choose B ID the channel name ID 1 Press the V A buttons to choose a To cancel the ID function TV channel Press the BACK button Every time you press the V A buttons the programme number PR changes and the picture of the TV channel stored in the programme number PR appears on the 6 Press the OK button to give a channel name ID to a TV channel e You can give your own unique channel screen BEN name ID to the TV channel When 2 Press the red button to start the ID you have finished step 3 do not go to function step 4 Press the lt P buttons to move the cursor and press the W A buttons to choose each character of the channel name ID Then press the OK button to register the channel name ID to the TV channel Before performing INSERT or T MANUAL operation 000 If you register the TV channel SECAM L system from a French station be sure to set the COUNTRY setting to 3 Press the V A buttons to choose FRANCE If the COUNTRY setting is the first character of a channel not set to FRANCE perform steps 1 and 2
64. vent the sound from being issued Follow the description EDIT MANUAL on page 33 to use the MANUAL function to try to change the SYSTEM setting B Poor picture f noise snow totally blocks out the picture there may be a problem with the aerial or aerial cable Check the following to try to solve the problem Have the TV and aerial been connected properly Has the aerial cable been damaged Is the aerial pointing in the right direction Is the aerial itself faulty If the TV or aerial suffers interference from other equipment stripes or noise may appear in the picture Move any equipment such as an amplifier personal computer or a hair drier that can cause interference away from your TV Or try moving the TV If the aerial suffers interference from a radio tower or high voltage wire please contact your local dealer If the TV suffers interference from signals reflecting from mountains or buildings double pictures ghosting will occur Try to change the aerial s direction or replace it with one with better directionality Are your COLOUR SYSTEM settings correct Follow the description COLOUR SYSTEM on page 28 to try to solve the trouble Have the COLOUR and BRIGHT settings been adjusted properly Follow the description BRIGHT and COLOUR on page 26 to try to adjust them properly Videotaping teletext is not recommended because it may not record correctly When a white and bright still

JVC InteriArt HV-36P38SJE User's Manual

Contents

Download Pdf Manuals

Related Search

Related Contents