Install the Front panel Assembly
Contents
1. Low Voltage Protection When the battery is low there are alarm signals to warn users to change the battery as follows 1 When the battery voltage is lower than 4 8V the buzzer will make short sharp sounds for five times when starting the machine Users can unlock it normally but fail to enter the administrative mode 2 When the battery voltage is lower than 4 5V the buzzer will make short sharp sounds for five times and then the machine will be switched off automatically or When the low voltage alarm occurs please change the battery in time to avoid the impact on the work of the fingerprint lock Avoid losing data caused by instable power supply It is suggested to change the battery immediately when the battery voltage is lower than 4 8V X The Basic Operation I Change Master Pass Code MPC 1 Press La key to start lock and then enter the Verify State The LED flashes green light and the Numpad area s blue light will be on 2 Press and hold the La key until you hear 1 long beep and the Green LED put out and then the Keypad area Flashes Blue light Press number key of the lock to input the default MPC 98989 and then press La key to enter the Management Mode The green LED put out and the Keypad area continue flash blue light 10 3 Press 5 key on the lock and enter the new 5 digits MPC then press the La key to confirm Enter the new MPC once again then press the La key to confirm Once you hear long2. Ordinary User Mode 13 3 Input 000 and press La key to confirm then input 000 again and press La key to confirm The buzzer will give a long beep the Ca key flash green light namely successful delete all users ES Notice The operation can only delete ordinary users If you want to delete administrator you should do reset operation XI Routine Maintenance 1 The lock surface is forbidden to contact corrosive substances Otherwise the protective layer of the lock surface may be damaged and therefore the glossiness of the lock surface may be decreased To keep the lock surface glossy use the furniture polish wax to polish the lock surface regularly 2 Use the cloth to clean dirt after the fingerprint collector is used for long time 3 Change batteries in time when the alarm on the low power rings You must replace the four old batteries with four new batteries of the same brand the alkaline battery of 1 5 V once 4 Regularly check whether screws are loose
3. BL100 Installation Guide Version V1 0 Date 2012 3 16 I Reference Tools for Installing the Door Lock f f 1 Hammer 2 Screwdriver 3 Chisel for wood working 4 Angle square 5 Percussion drill 6 Hole saw 7 Polisher 8 Rivet gun 9 Carpenter s pencil 10 Pliers II Quick Reference A Quick reference for Installation Guide gt VV VV VV V WV Confirm the door information before installation please see II Confirm the door information before installation Install Lock Body please see IV Install Lock Body Confirm the length of Locking Bar please see V Confirm the length of Locking Bar Install the Front panel Assembly please see VL Install the Front panel Assembly Install Batteries please see VII Install the Batteries Install the Rear panel Assembly please see Vill Install the Rear panel Assembly Use Instruction please see IX Use Instructions The Basic Operation please see X The Basic Operation Routine Maintenance please see XI Routine Maintenance 1 B List of Lock Accessories Keyhole Screw 4 PCS 4 PCS AA Cover Front panel 7 Assembly a Batteries Silica gel Rear panel backing plate assembly 10 Lock body Screw 2PCS Back Lining Key 2PCS Plate Il Confirm the door information before installation 1 Installation Requirements This fingerprint lock is not configured with a handle and the user can install it on the door as desired The fingerprint lock is applicab
4. beep and the La key flashes green namely you have successfully changed the MPC code II Enroll an Administrator 1 Press La key to start lock and then enter the Verify State 2 Press and hold the La key until you hear 1 long beep enter the 5 digits MPC and then press La key to enter the Management Mode 3 Press 9 on the lock to enter the Enroll Administrator Mode gt Enroll a Fingerprint Administrator User OQ note 1 3 steps are same as above Here is no longer to restatement 4 After enter the Enroll Administrator Mode press number keys of the lock to enter 3 digits user ID and then press La key to confirm rote The administrator User s ID must between 995 and 999 5 Press finger in the scanner area properly and repeat it for three times until you hear one long beep and LED flashes Green gt Enroll a Password Administrator User OQ note 1 3 steps are same as above Here is no longer to restatement 4 After enter the Enroll Administrator Mode enter 3 digits user ID press La key to confirm 5 Press 4 digits user password and press La key to confirm and then enter the 4 digits user password once again and press La key to confirm until you hear one long beep and LED Flashes Green If it fails to register it will give 2 short beeps and LED will flash red OQ note If Pass code does not match or input the wrong digit password then you have two times to try again If your input the wrong at
5. cking Bar that stretches out of the Hole Slot on the door is CD as shown in Figure 11 Cut away the Locking Bar from A to ensure that the Locking Bar does not stretch out of the Hole Slot VI Install the Front panel Assembly 1 Install a Silica gel backing plate on the f Front panel Assembly moisture proof waterproof As shown in Figure 12 Silica gel backing plate a ae N Locking Bar Spring Bolt Connecting Line Figure 13 Front panel Assembly 2 Stretch the Spring Bolt back to the Lock Body and pull the Connecting Wire out of the hole at the bottom of the Lock Body 3 Install the Front panel Assembly into the matching Hole Slot on the door There are three holes on the Lock Body as shown in the preceding figure The cylinder on the fore plate composition must be pulled out from the cross shaped hole of the Lock Body and the Locking Bar must be vertical to the ground as shown in Figure 13 4 Install the Back Lining Plate to the mapping Hole Slot Pull the Connecting Wire out of the Oval shaped Hole of the Back Lining Plate As shown in Figure 14 and fix the Back Lining Plate and Front panel Assembly using a screwdriver as shown in Figure 15 Silicone Pad Back Lining Plate Connecting Line Oval shaped Hole _6 3 Cover the Silica gel Backing Plate onto the Rear panel Assembly turn the Lock Button to make the Hole Slot vertical to the ground and insert Locking Bar into the Hole Slot as shown in Fi
6. gure 19 In this case when you turn the Lock Button the bolt can sprung out or back automatically VI Install the Batteries 1 Prepare four AA batteries You are advised to use new batteries with the same brand 2 Put batteries into the Rear panel Assembly properly As shown in Figure 16 1 and 16 2 igg Slot RGT a we Vertical H A fe ws See ee Sat AA batteries i Set PFS an te a a Sry Figure 20 Rear panel Assembly Lock Button 4 Push the Rear panel Assembly ahead to ensure that it can cover the whole Back Lining Plate Install screws and Y Figure 16 2 fix them using a screwdriver As shown in Figure 20 Figure 16 1 IX Use Instructions Vil Install the Rear panel Assembly 1 Pull the Connecting Wire into the Wire Hole of the Rear panel Assembly As shown in Figure 17 st 1 Panel Description Screw Hole 1 Fingerprint Collector Start key LED Status indicator Number keys 4 Key Hole Figure 18 Emergency Power Interface Connecting Line Figure 17 2 Tuck up the Connecting Wire for further Rear panel Assembly installation As shown in Figure 18 ay 2 Precautions 1 After the fingerprint lock is installed the lock is in the test state and therefore any fingerprints and passwords can open the lock You must modify the Master Pass Code MPC The lock can be used normally only af
7. igure 4 2 2 Rotate part by 45 in the other direction to make the card pillar of the Lock Body to be embedded into the matching card hole of 70 mm That is set the length of the Lock Body to 70 mm OQ note When you shorten the length of the Lock Body perform the following steps 1 Hold the part rotate the part by 45 and push part ahead 2 Rotate part by 45 in the other direction to make the card pillar of the Lock Body to be embedded into the matching card hole of 60 mm 4 3 After the procedure is completed fix the Lock Body using a screwdriver as shown in Figure 6 Insert the screwdriver into the cross shaped hole of the Lock Body When you rotate the cylinder clockwise it springs out automatically as shown in Figure 7 When you rotate the cylinder counterclockwise it springs back automatically as shown in Figure 8 Figure 7 i Figure 8 V Confirm the length of Locking Bar 1 Install the Front panel Assembly of the lock onto the door Please see VI Install the Front panel Assembly As shown in Figure 9 Figure 9 cu Figure 11 Figure 10 if p l Ga i ie ie He N a H k D ce ff j i f N 2 Check whether the Locking Bar is too long If yes take the Front panel Assembly off and cut away the excess part of the Locking Bar see Method for Cutting Locking Bar As shown in Figure 10 Method for cutting Locking Bar Suppose that the part of the Lo
8. le to doors of 35 50 mm in thickness 2 Make sure of the door opening directions and lock body directions 1 Make sure of the door opening directions The lock body s outside and inside can t be set contrary Assume you are standing outside and facing a door and then there are four door opening directions Left inward left outward right inward and right outward Left inward outward means the door swings inward outward with hinges on the left right inward outward means the door swings inward outward with hinges on the right as shown in the following Figure 1 2 Make sure of the lock body directions According to the door opening directions to make sure of the lock body directions shown as the following Figure 2 Indoor Tadoael J H Left Inward Right Inward Indoor Indoor Figure 1 Left Outward Right Outward To set the lock as Left Open or Right Open on the Rear panel Assembly shown as Figure 3 Left Open Right Ope Set Switc N NENI ace P FS hess ead j Rna M MR ass Gorse ee SA Right Open ne Left Open Figure 3 As shown in Figure 3 there has a Left open Right Open set Switch on the Rear panel Assembly of the fingerprint lock The user can turn the switch to the left side L namely set the door s opening directions as Left Open if turn the switch to the right side R then set the door s opening directions as Right Open Note Before in
9. n press the a key to lock 2 If the password is wrong then the verification failed The buzzer will give two short beeps the RED LED at Ca key will light for 3s then the green LED will flash the user can input password to verify again until verify successful OQ note After successful verification the lock is in unlocking state If you want to lock press La key to start the lock and then press this key again to lock and power off V Delete User gt Delete a user 1 Press La key to start the lock and enter the Verify State See the methods on how to enter the management mode in the Enroll a Fingerprint Ordinary Users 2 Press 3 on the lock to enter the Delete User Mode 3 Press number key of the lock to input the User s ID which one you want to delete and then press La key to confirm Input the user ID again and press La key to confirm the buzzer will give a long beep the La key lights green light namely successful delete the user 4 After deleting the user you can restart the fingerprint lock and verify the deleted user s fingerprints or password again to check whether the user is deleted for sure ES Notice The administrator can t delete itself and the last administrator gt Delete All Ordinary Users 1 Press La key to start the lock and enter the Verify State See the methods on how to enter the management mode in the Enroll a Fingerprint Ordinary Users 2 Press 6 on the lock to enter the Delete All
10. stall the fingerprint lock you must make sure of the door s opening direction as Left Open or Right Open at first According to the door s opening direction switch the Left Right Open set switch to the corresponding position Left Open then switch to the left side Right Open then switch to the right side According to the door s opening direction to drill a hole and trough in the door and then install the Lock Body ee IV Install Lock Body 1 Determine the installation height and installation location stick the hole drilling template to an appropriate location according to the door opening mode as shown in Figure 4 1 2 Insert the Lock Body into the matching Hole Slot as shown in Figure 5 BS Note There has a fUP flag on the Lock Body Before installing the Lock Body confirm how to install it based on the tip flag 60mm 7Omm Pad i The hole of spring bolt j should be in the ss KO line of the door thick Set the length of the Lock Body based on the distance from the Door Edge to the center of the circle that is the Figure 42 Figure 5 opening hole distance is about 60 mm or 70 mm as shown in Figure 4 1 The opening distance matching the default length of the lock body is 60 mm If the distance of 70 mm is required reset the length of the lock body in the following steps 1 Hold the part of the Lock Body rotate the part by 45 and pull back part As shown in F
11. ter the User ID of an administrator is entered If the MPC is not modified the other functions of the system except for the initialization system are not available in the management mode If no administrator is registered ordinary users cannot also be registered OD note The method and step of change Master Pass Code Enroll Administrator and Enroll Ordinary user please see BL100 Fingerprint Lock User Manual 2 Do not remove batteries when matching enrolling or deleting fingerprints because the sudden power down may result in data loss of fingerprint locks Prior to removing batteries make sure the fingerprint lock 1s not in working state 3 It is recommended to replace the fingerprint lock batteries at least once every six months to avoid damaging the circuit due to the battery leakage Do not use batteries with poor quality 3 LED Backlight Indicators The LED Backlight Indicators content three colors Red Green and Blue gt The general rule Successful 1 Long Beep LED Flashes Green Failed 2 Short Beeps LED Flashes Red gt Verify State Green LED flash by second gt Management Mode Blue LED flash by second 4 Unlock with an Emergency Mechanical Key You can open the door using an emergency mechanical key in case the electronic component does not operate Use your fingernails or a hard chip to take down the lock cover 2 Insert the emergency key into the keyhole and rotate 90 to unlock 5 Battery
12. the third time then it will prompt fail registration In this case you will need to follow step 1 to operate again If successful it will automatically exit the Enroll Administrator Mode Press and hold 0 key can exit anytime If you want to enroll more administrator user and then repeat the step 1 5 11 III Enroll an Ordinary User gt Enroll a Fingerprint Ordinary User 1 Press La key to start the lock and enter the Verify State 2 There have two methods to enter the Management Mode Press and hold the La key until you hear 1 long beep enter the 5 digits MPC and then press La key to enter the Management Mode Verify the registered administrator s password and fingerprint to enter the Management Mode 3 Press 1 to enter the Enroll Ordinary User s Fingerprint Mode 4 Input 3 digits User ID then press La key to confirm Ore The ordinary users ID must between 001 and 994 5 Press finger in the scanner area properly and repeat it for three times until you hear one long beep and LED flashes Green namely enrollment successful gt Enroll a Password Ordinary User 1 Press La key to start the lock and enter the Verify State Enter the Management Mode see the methods on how to enter the management mode in the Enroll a Fingerprint Ordinary Users 2 Press 2 on the lock to enter the Enroll Ordinary User s Password Mode 3 Input 3 digits User ID and press Ca key to confirm OQ note The ordinary
13. users ID must between 001 and 994 4 Input 4 digits user password press La key to confirm Enter the 4 digit user password once again and press La key to confirm until you hear one long beep and LED flashes Green The Keypad area lights blue LED and the La key lights green LED namely register successful IV User Verification gt The Fingerprint Verification 1 Press La key to start the lock and enter the Verify State The Fingerprint Collector is in active state 2 Press finger in the fingerprint scanner area properly until you hear one long beep namely collect successful 1 If verify successful the buzzer will give a long beep and unlock automatic the green LED and the Fingerprint Collector will put out the Green LED at La key will light for 3 seconds at this moment your can press La key to lock 2 If verification failed The buzzer will give two short beeps the red LED at La key will light for 3s then the green LED will flash the user can use fingerprint to verify again until verify successful gt The Password Verification 1 Press La key to start the lock and enter the Verify State 2 Press number key of lock to input the correct 4 digits password and press La key to confirm 1 If the password is correct then verify successful the buzzer will give a long beep and unlock automatic the green LED at Fingerprint Collector will put out the Green LED at La key will light for 3s at this moment you ca
Download Pdf Manuals
Related Search