automatic drum washing machine user manual tkw 1070
Contents
1. AFTER WASHING Turn off the water supply and unplug the power cord Open the washer door to prevent formation of moisture and odours Let the door open while not used TIPS FOR SAVING ENERGY Collect clothes for one full wash load Avoid overloading the washing machine Prewash only heavily soiled clothes Reduce the amount of detergent or choose standard or delicate wash programs tor slightly soiled clothes Choose a proper washing temperature Modern detergents can wash with very good result already in lower oe than 60 C Only use higher temperature than 60 C for heavily soiled laundry 6 Follow the dosage recommendation on the detergent package to avoid using too much detergent CARE CHART TOF Resistant material AN Bleachable in cold water e Don t dry dean X27 Delicate fabric zx Do not bleach Dry flat Washable at 95 C ed Iron at 200 C IN Hung to dry Washable at 60 C e Iron at 150 C Mm Dry on clothes hanger Washable at 40 C ex iron at 100 C C Tumble dry normal heat Washable at 30 C ed Don t iron Tumble dry reduced heat d Hand wash A Dry cleaning with any solvent OO Don t tumble dry EF Dry clean only B Dry cleaning with peridoride Wool Seal Dry cleaning with aviation fuel LOAD REFERENCE Bed sheet single Cotton Approximately 800g Blanket Wool Approximately 3000g Blended fabric dothes Approximately 800g Jackets Cotton Approximately 800g Jeans Jl Appr2. Open the detergent distribution drawer during the wash cycle i Force the washer door open The door is fitted with a self lock device and will open shortly after the washing procedure is ended Open the washer door if the water level is visibly over the porthole Al Cover the washing machine with plastic cover so that inside dampness cannot be kept in INSTALLATION DISMANTLE THE TRANSPORTATION BOLTS The transportation bolts are designed for clamping anti vibration components inside of the washing machine during the transportation process Remove the back cover 2 Remove the four bolts on the rear side and take out the synthetic stabilisers from within the machine 3 Replace the back cover 4 Fill the holes left by the bolts with blanking plugs Note 1 When you replace the back cover the convexity must face to outside and you have to insert the back cover from the two gaps as shown in fig 5 2 Keep the transportation bolts and synthetic stabilisers in a safe place for later use ADJUSTING THE WASHING MACHINE There are adjustable feet under the bottom of the washing machine Before use they should be adjusted so that the machine is level This will minimise vibrations and thus noise during use It will also reduce wear and tear We recommend using a spirit level to level the appliance The floor should be as stable and flat as possible INLET HOSE 1 Connect the nu
3. Excessive use of detergent drawer The washing program duration will be adjusted _ This is normal and doesn t affect the functionality Unbalance of the laundry Add clothes or run a spinning program again WIRING CIRCUIT NTC J3 5 J3 4 J4 3 J2 1 J2 2 M9 J1 6 J1 5 J1 7 M10 Ne i N 4 4 PCB aa FA3 Lt qp M1 i MR J1 4 Ms jig MS MR MRN J1 3 MRC J3 2 M6 J3 3 J2 9 2 7 J2 4 M7 EVF EVP PS Motor Motor PCB Printed Circuit Board MR Door Lock R Heating Element PS Drainage Pump EVF EVP Water Inlet Magnetic Valve P Pressure Switch FA Interference Suppresser NTC Temperature Sensor MOTOR FUSE
4. USER MANUAL TKW 10 0 16 20 ABLE OF CONTENTS BEFORE USE USING THE APPLIANCE MAINTENANCE SCOMPONENTS sss 03 PROGRAM SELECTION 10 gt DISPLAY CODES okesssscti tones 18 PEREPARATIDN sctccctiiieosanta 04 CONSUMPTION AND TECHNICAL DATA 11 TROUBLESHOOTING 19 gt SAFETY INSTRUCTIONS 05 WASHING METHODS 12 gt WIRING CIRCUIT 20 SINSTALLATION 06 CLEANING amp CARE 16 SCONTROL PANEL 08 LEGEND lV Yes ZA No Optional For your safety any instructions in this manual with this Warning sign must be followed strictly DISPOSAL As a responsible retailer we care about the environment As such we urge you to follow the correct disposal procedure for your product and packaging materials This will help conserve natural recourses and ensure that it is recycled in a manner that protects health and the environment You must dispose of this product and its packaging according to local laws and regulations Because this product contains electronic components the product and its accessories must be disposed of separately from household waste when the product reaches its end of life NENNEN Contact your local authority to learn about disposal and recyding The product and packaging should be taken to your local collection point for recycli
5. and for satety Wipe clean the lower part of the porthole Keep the door slightly open when the washing machine is not in use to prevent formation of odours Let the power cord be replaced by the manufacturer his service agent or other accordingly qualified persons in case it is damaged V Ensure that the appliance is not used by persons with reduced physical sensory or mental capabilities lack of experience and knowledge without supervision or instruction by a person responsible for their safety Supervise children to ensure that they do not play with the appliance DO NOT Al Touch or use the appliance when barefoot or with wet or damp hands or feet Use flammable detergent or dry cleaning agent Use any flammable sprays in close vicinity to the appliance Remove or insert the plug in the presence of flammable as VA Allow children or infirm persons to play with the appliance or packing materials Z Install the appliance outdoors in a damp place or in an area which may be prone to water leaks such as under or near a sink unit In the event of a water leak allow the machine to dry naturally Place the washing machine directly on a carpet or close to a wall or furniture DO NOT A Touch the washer door during the washing process it ets hot Vi Place heavy objects or sources of heat or damp on top of the appliance Hot wash foam rubber or sponge like materials
6. 30 C 40 60 C 40 C v C C Different materials 1000 rpm 9 AT Delicado 30 C t0 40 C 30 C M Ei E Cotton or synthetic 1000 rpm 10 OTST Adorado H E I U A meetin 11 T6Y Centrifugado v Z Z ZA 1000rpm v Yes VA No Optional CONSUMPTION TABLE The wash cycle times are intended as a guide only The actual time used may vary due to different water pressure initial water temperature etc PROGRAM 187 Lana 30 C 1X7 Sint tico 40 C 167 Eco 40 C 187 Algod n 40 C Eas Prelavado 40 C 721 R pido 15 l ligero 30 C EX Mixto 30 C 125 Delicado 30 C MAX LOAD 2 kg 4 kg 4 kg 1 8 kg 1 8 kg 4 kg 4 kg 7 0 kg 4 kg ENERGY CONSUMPTION 0 34 kWh 0 71 kWh 0 78 kWh 0 83 kWh 1 08 kWh 0 11kWh 0 34 kWh 0 78 kWh 0 3 kWh WATER CONSUMPTION 55L 50L 44l 46 5L 68L 25L 30L 50L 50L TEMPERATURE 30 C 40 C 40 C 40 C 40 C 30 C 30 C 40 C 30 C WASHING TIME 1 00 h 1 10h 1 18h 1 38 h 1 46 h 0 15h 0 25 h 1 15h 1 01h EN 60456 test program Energy label program with Standard 60 C and max spin speed and Intense function TECHNICAL DATA Power source Max working current A Water pressure MPa Nominal load kg Spinning speed r min Washing programs Max power W Dimensions HxDxW mm Net weight kg TKW 1070 220 240V S0Hz 10 0 03 P 1 7 1000 11 2000 850 x 600 x 595 70 ASHING METHODS This washing machine is
7. e is less than 0 03 Mpa _ Check water pressure The inlet hose is kinked _ Check the inlet hose Water supply failure _ Ensure the water supply The program knob is not properly set _ Set the program knob properly The washer door is not properly closed _ Close the washer door properly The inlet hose filter is blocked Unblock the inlet hose filter The height of the drain hose is below 80 cm Install drain hose within 80 100 cm of height The drain hose is in water _ Make sure the drain hose is not in water Drain hose is blocked _ Unblock the drain hose Drain hose end is higher than 100 cm above _ Make sure the drain hose end is lower than the floor level 100 cm above floor level The filter is blocked Unblock the filter Not all transportation bolts have been removed _ Remove all transportation bolts Washing machine is located on an uneven _ Make sure the washing machine is on surface or is not level an even surtace and levelled Machine load is over 7 kg _ Reduce amount of laundry in the drum Water or electricity failure _ Check the power supply Washing machine gives an error message Check display codes Washing machine is in soaking cycle _ Press the rinse hood button or the Start pause button again to cancel it The detergent is not a low foaming type or for _ Check if your detergent is appropriate manual wash _ Reduce amount of detergent in the distribution
8. e slightly different from the layout of the washing machine you have just purchased due to technical improvements Control panel Drain hose Door handle Water inlet valve Work top Washer door Power cord Power Back cover screws Detergent distribution drawer Back cover Filter cover Transportation bolts SAFETY INSTRUCTIONS BEFORE SWITCHING THE APPLIANCE ON FOR THE FIRST TIME DO V Make sure that the transport bolt are removed IV sea separate earthed socket for the power supply Make sure that the plug is accessible V Hold the plug and not the electric cable when unplugging the power supply Make sure that the fuses in the power circuit are rated for 15A VI Keep away from heat sources and direct sun light to prevent plastic and rubber components from aging Make sure that the power cord is not caught under or in the appliance and avoid damage to the power cable V Check that hose joints and connections are firm and no water can leak If joints are loose or there is leakage turn off the water supply and refix Do not use the washing machine until the hoses are properly fixed DURING DAILY USE OF THE APPLIANCE DO IV Pul up zips and fix loose threads to prevent the items from being entangled If necessary put small items into a net bag or pillow V Tum off the machine after each wash program and switch it off at the mains to save electricity
9. e the above steps again so the alarm sound can be recovered and the display will show bEEP ON 2 Note During the spin process if too much foam is inspected in order to protect the motor the washing machine will eliminate the foam automatically the motor will stop and the drain pump will drain the water continuously for 90 seconds If it happens more than 3 times the motor will stop until the end of cycle without spinning TROUBLESHOOTING TROUBLESHOOTING The following circumstances do not constitute problems Do not contact the Service Center until the problem has been confirmed PROBLEM Washing machine fails to operate Washing machine cannot be filled with water Machine is draining while being filled Drainage failure Strong vibration while spinning Operation stops before completing wash cycle Operation stops for a period of time Excessive foam in the drum which is spilled to the distribution drawer Automatic adjustment of the washing time Spinning fails CAUSES SOLUTIONS Poor connection to the power supply _ Check connection to the power supply Power failure Check the power supply The washer door is not properly closed Close the washer door properly Machine has not been switched on _ Make sure the machine is switched on The Start Pause button is not pressed _ press the Start Pause button Water tap is not turned on _ Turn on the water tap Water pressur
10. eign substances clean the water inlet valve and inlet valve filter regularly MOVING THE MACHINE If the machine is to be moved to a distant location replace the transportation bolts removed before installation to prevent damage as shown below Remove the blanking plugs Remove the back cover Insert the synthetic stabilisers and the transportation bolts Tighten the bolts with a spanner Replace the back cover LONG PERIODS OF DISUSE IF the washing machine is left idle for a long period pull out the electrical plug and turn off the water supply Open the washer door to prevent formation of moisture and odours Let the door open while not used DISPLAY CODES DISPLAY CODES AND SPECIAL FUNCTIONS CODES CAUSES SOLUTIONS Err Door is not properly shut _ Shut the door properly Err Drainage error water not emptied within 6 _ Clean the filter and check the drain hose for blockage If error minutes still exists please contact the maintenance personnel Err3 Temperature sensor not properly connected or _ Contact the maintenance personnel damaged Err4 Heater error Appears at the end of a cycle _ Contact the maintenance personnel Err5 Water level not met in 8 minutes Make sure that tap is turned on and water pressure is normal If problem still exists please contact the maintenance personnel _ Install drain hose within 80 100 cm of height _ Make sure the drain hose is no
11. for domestic use only If the machine is use for commercial purpose the guarantee will not be valid anymore Do not use it for purposes other than that for which it was designed Follow the instructions given on the label of each garment and wash only machine washable garments POWER SUPPLY Connect the washing machine to the power supply 220V to 240V 50Hz WATER CONNECTION Turn on the tap The water must be clean and clear Note Before use check for leakage in the joints between the tap and the inlet hose by turning on the tap PREPARING THE LAUNDRY Sort out clothes according to fabric cotton synthetics wool or silk and to how dirty they are Separate white clothes from coloured ones Wash them first by hand to check if they fade or run Empty pockets keys coins etc and remove the harder decorative objects e g brooches Attention Small parts like buttons etc may lead to repair work which user has to pay by themselves and can cause damage in the machine Garments without hems underwear finely woven textile such as fine curtains are to be put into wash bag it is better not to wash them in a washing machine lose zippers and hooks make sure the buttons are sewn on tightly and place small items such as socks belts bras etc in the wash bag Untold large pieces of fabric such as bed sheets bedspreads etc 4 Turn shirts inside out LOADING THE MACHINE Open the washer door put
12. in the laundry piece by piece Close the door tightly When first using the washing machine let it run unloaded for one program to prevent the laundry from being tainted by oil or dirty water from the washing machine Before washing you should run the machine without laundry but with detergent with 60 C programm Do not overload the washing machine SELECTING DETERGENT The washing efficiency and the performance is determined by the quality of detergent used Special non foaming detergent produces good washing results Use specitic detergents for synthetic and woollen goods Do not use dry cleaning agents such as trichloroethylene and similar products Note Do not add more detergent than needed otherwise it may cause the situations as following and washing machine malfunction impacting washing machine s life 1 Due to the increasing foam the rinse time will be longer than normal 2 The foam may overflow from the detergent drawer because of the increasing pressure of the foam 3 It may remain foam without cleaning out after the final spinning cycle Recommendation 1 Clean the detergent drawer once a week 2 When using the prewashing program please add half of the rating dosage 3 Please follow the dosage recommendation on the powder or liquid detergent package ADDING DETERGENT Slide out the detergent drawer and put the required detergent and softening agent into the corresponding compartments Push back the drawer gent
13. ly Refer to the instructions on the drawer Caution For prewashing program detergent should be added to both compartments 1 and 2 For other programs do not add detergent to compartment 1 Use liquid detergent according to the instructions on its package Do not use liquid detergent if the prewash mode or Start delay is selected Do not overuse softener otherwise it will damage the artificial fibers SELECTING PROGRAM To get the best washing results an appropriate washing program should be selected according to the laundry type Please turn the program knob to select the right program SELECTING FUNCTIONAL Select the required options Reter to the Control panel pages 08 and 09 SETTING WASHING TEMPERATURE Press and hold down the temperature button until the desired temperature is selected SETTING SPIN SPEED Press and hold down the speed button until the desired speed is selected See Operational functions on the Control panel pages 08 and 09 for selecting temperature and spin speed It is advisable to select the recommended value WASHING Press the Start Pause button The washing machine will operate according to the preset programs The washing machine will stop operation automatically when a washing cyde ends The End sign will appear on the display Open the washer door and take out the laundry
14. ndicator Select a temperature button temperature according to the type of laundry Note If there is no indicator light displayed it means cold wash F Delay Button Touch this button lightly the washing machine will start operation after a period of time and the corresponding indicator will go on The range is 0 5 24 hours each touch of this button increases a half hour After the button is set press the Start Pause button to start countdown of the set time the time is displayed on the screen until the program ends Note The delay time must be longer than the program time otherwise the washing machine will start the wash program directly G Detergent Open the drawer three compartments can be distribution drawer seen Compartment 1 Prewash detergent Compartment 2 Detergent for programs 1 to 10 Compartment 3 Softener conditioning agent perfume etc H Display Information as remaining wash time and error messages will be shown here Note After power is switched on the display will go on and the remaining wash time decreases As the water pressure and temperature may differ the remaining time maybe adjusted accordingly When the laundry is not balanced during spinning the time may be automatically prolonged These are normal phenomena Eco Before a washing program select this program to set the washing load 1 2Full the washing machine will automatically adjust the water consumption and washing time J Intense but
15. ng Some collection points accept products free of charge We apologize for any inconvenience caused by minor inconsistencies in these instructions which may occur as a result of product improvement and development COMPONENTS THANKS FOR PURCHASING A TEKA PRODUCT Please read these instructions carefully before using this appliance The instructions contain important information which will help you get the best out of the appliance and ensure safe and proper installation use and maintenance Keep this manual in a convenient place so you can always refer to it for the sate and proper use of the appliance If you sell the appliance give it away or leave it behind when you move house make sure you also pass on this manual so that the new owner can become familiar with the appliance and safety warnings ACCESSORIES Check the accessories and literature in accordance with this list 1x Inlet hose assembly 1x Drain hose bracket MANUAL DEINSTRUCCIONES BeDieNuNGSANLETUNG INSTRUCTION MANUAL 1x User manual 4x Blanking plugs 1x Warranty card fera PREPARATION PREPARING THE MACHINE Remove all the packing materials to prevent unsteadiness including the polystyrene base Upon opening the package water drops may be seen on the plastic bag and the porthole This is normal phenomenon resulting from water tests in the factory DESCRIPTION This diagram may b
16. oximately 800g Overalls Cotton Approximately 950g Ladies Pyjamas J Approximately 200g Shirts Approximately 300g Socks Blended fabrics Approximately 50g T Shirts Cotton Approximately 300g Underwear Blended fabrics Approximately 70g CLEANING amp CARE AFTER WASHING Turn off the water supply and pull out electricity plug after each wash Open the washer door to prevent formation of moisture and odours If the washing machine is left idle for a long period drain the water in the machine and replace the drain hose CLEANING THE DETERGENT DRAWER Clean the detergent distribution drawer regularly Swing out the drawer flush it dean with water and then replace if CLEANING THE MACHINE Unplug the machine during cleaning and maintenance Use a soft cloth dampened with soap liquid to clean the machine case and rubber components Do not use organic chemicals or corrosive solvents CLEANING THE FILTER Clean the filter once a month 1 Open the bottom cover 2 Remove the filter by turning counterclockwise 3 Flush the filter clean with running water 4 Replace the filter by turning clockwise and remount the cover Caution The filter must be in place or it may lead to leakage 2 Place a container under the drain pump filter to collect any excess water that may come out of the drain pump when the filter is removed WATER INLET VALVE AND INLET VALVE FILTER To prevent blockage to the water supply by ingress of for
17. t in water The height of the drain hose is below 80 cm The drain hose is in water Err7 Motor error _ Contact the maintenance personnel Err8 Water exceeds protective level _ Contact the maintenance personnel End End of wash cycle 1 25 The remaining time is 1 hour 25 minutes 19 30 Status information Preset time for delayed operation UNb After the last rinsing cycle finishes spinning fails completely due to unbalance of the laundry Control panel lock function Press the Delay and the Start Pause buttons simultaneously for 3 seconds after starting a program It can no longer be changed by operating buttons or knobs To unlock press the Delay and Start Pause buttons again for 3 seconds Power off memory function In case of abrupt power failure or the need to cut off the power during a program cycle the present settings will be saved and the preset operation will resume when the power is on again To cancel a program Press the Start Pause button then switch off the power and the program is automatically cancelled Turn the program selector again to choose another program 1 Marm sound can be cancelled if it is needed Please follow the instruction as below Switch on the washing machine and turn the program knob to spin cycle then press the Delay and Extra rinse button hold on for 3 seconds The bEEP OFF will be displayed on the screen which indicates that alarm sound has been canceled To operat
18. t on the inlet hose to the connector on the water valve 2 Apply inlet hose to a water tap with cold fresh water Note Use the hose set supplied with the appliance Old hose sets should not be reused DRAIN HOSE 80 100cm 1 Use the drain hose bracket to keep the end of the drain hose retained and prevent the outflow of water Don t extend the length of the drain hose if an extended hose is required please consult a serviceman SS ee ee ee ee ee ee 2 The height of the drainage outlet must be 80 100 cm Fix the drain hose to the clip at the back of the washing machine to prevent it from dropping off Note The drain hose should not be submerged in water and should be securely fixed and leak free If the drain hose is placed on the ground or if the pipe is at a height of less than 80cm the washing machine will continuously drain while being filled self siphoning CONNECTING TO THE POWER SUPPLY Before connecting to the power supply check The socket is adequate for the maximum power of the washing machine For safety fuses in the power circuit should be rated for no less than 15A The voltage should meet the requirement The power outlet should be capable of accepting the washing machine plug Connect the machine to an earthed socket outlet CONTROL PANEL TKW 1070 B A EDJK C A Program knob G Detergent distribution drawer B Power Switch H Display C Start Pause but
19. ton I ECO D Spinning Speed Setting button J intensa bution E Washing temperature button K Eust F Delay Button OPERATIONAL FUNCTIONS A Program knob _ By turning the knob clockwise counterclockwise the required program can be selected There are 11 programs available After a program is selected the corresponding light will go on B Power Switch _ Press this button to switch on the washing machine Press it again to switch it off Press On Off button gently for 2 seconds to switch off the machine as buttons are sott touch sensitive Start Pause _ When the washing machine is connected to the power socket and a program is selected lightly Button touch this button to start operation During a wash cycle touch it lightly operation will stop and the digits on the screen start blinking Touch it again to resume operation To cancel a wash program during a wash cycle touch this button when the digits on the screen start blinking press the Power switch the program will be cancelled D Spinning Speed _ Touch this button lightly to select the desired speed When a speed is set it will be displayed on the Setting Button indicator Note If there is no indicator light displayed it means no spinning Note Different water temperatures and spinning speeds can be set for different laundries Wash using the default settings if there is no special requirement E Washing Touch this button lightly the washing temperature will be displayed on the i
20. ton If the laundry is heavily soiled press this button before starting the program When the button is pressed the washing time increases K Extra rinse button Press this button the washing machine will perform additional rinses Press the button once to select one additional rinse The display will show P 1 Press the button repeatedly and the screen will display P 2 or P 3 indicating two or three additional selected rinses The extra rinse light is activated and flashes during the performance P 1 2 3 is displayed alternating with the remaining time The light turns off and the display disappears when the extra rinse ends Note Select this function when programe 1 9 is selected PROGRAM SELECTION PROGRAM MODES 1 Detergent compartment for prewash mode 2 Detergent compartment 3 Compartment for softener and other additives Temperature Program Maximum Preset 2 3 1 Recommended Laundry TKW 1070 157 Lana 30 C t040 C 30 C vi C Woolen fabrics 400 rpm 2 TRY Sint tico 40 C f0 60 C 40 C v LJ Fast colour synthetic 1000 rpm J 167 Fro 40 C t090 C 40 C v1 L C Cotton fabrics 1000 rpm A 187 Algod n 40 C t090 C 40 C v L Cotton fabrics 1000rpm 5 ES Prelavado 40 C 1090 C 40 C v C _ Heavy soiling 1000rpm 6 185 R pido 15 130 30 YJ L1 E Slight soil cotton linen 800rpm and synthetic fabrics 7 LX Ligero 30 C 1030 C 30 C vi 1L Sports wear 1000 rpm 8 en Mixto
Download Pdf Manuals
Related Search