MARK1 User Manual.indd
Contents
1. OPERATION 1 Power connection Make sure the MARK1 power switch is in the off position connect the power adapter DCSVOUT AUX OFF ON DEIN N Bio 004 i 1 2 Power on Switch the Mark1 the voice prompt Se will announce Power ON The front LED will be illuminated blue and the speaker is ready for use in Bluetooth mode 3 Bluetooth Speaker Controls Using the touch sensitive control buttons on the top of the speaker you can play pause answer the phone or select song using the top operation control panel 4 Incoming call operation PHONE When a call comes in you can answer the call by touching the PHONE icon button on the top control panel 5 Pairing Touch the PAIR button on the control panel the LED indicator will flash and the voice prompt will announce Pairing Make sure your mobile device is in pairing mode select the MARK1 speaker from the Bluetooth list in your mobile device Pairing is complete when you hear the tonal chime 10 112. pel With the speaker in Bluetooth mode Imre 7 place the NFC device screen 4 p gt unlocked and enabled near the speakers top panel NFC icon The voice prompt will announce pairing is complete when you hear the speaker tonal chime AUX input Make sure the MARK1 is turned off connect your audio source to the MARK1 with a 3 5mm audio cable Turn the MARK1 on you will hear the voice prompt announce Power on Touch the INPUT button on the top control panel the indicator will turn red and the speaker is in AUX in mode You can adjust the volume by touching the VOL and VOL on the control panel Control Panel ON OFF VOL VOL Press and hold the VOL and VOL 22 at same time for 3 seconds the NFC 4 gt LED Indicator will turn purple and T the control buttons are now inactive except the PHONE button Repeat these steps to activate the control panel buttons USB Charging Port The MARK1 has a standard USB charging port with DC5V 1A current output for powering or charging most devices Battery When the MARK is disconnected from a power source the speaker can be used in battery mode If the battery power is low the speaker will automatically decrease the volume to ensure sound quality and play time When the b
3. Please read this guide carefully before using this product SAFETY INSTRUCTIONS To prevent fire or electrical hazard do not disassemble this product Do not expose the unit to water or moisture Do not place liquid on or close to unit Do not place unit on or near an open flame or heat source Keep product free from dust and debris Place unit on a stable and level platform Do not place heavy items on top of unit Do not use excessive force when pushing the unit buttons Do not attempt to pull the power cord when removing it from power outlet Product uses Lithium Batteries please don t burn ingest or smash batteries Do not use damaged or defective power cables Unplug the power cable if the unit is not in use Clean with a damp cloth only PACKAGE CONTENTS 1 MARK1 speaker 2 Power adapter 3 3 5 mm audio cable 4 User manual CONTROL PANELS 1 Power Input LED 9 Pair Button 2 NFC Icon 10 Phone Button 3 Back Button 11 Volume Button 4 Play Pause Button 12 Charging Indicator 5 Forward Button 13 DC Power Input 6 Volume Button 14 Power switch on off 7 Input Select Button 15 AUX input 8 Microphone 16 Charging Port DC5V 1A 2 CONTROL PANELS FRONT PANEL BACK PANEL AUX OFF 1 2
4. ality HDMI cables Unassembled Kits A 45 day return policy applies to unassembled kits Once assembly has been started or completed kits are deemed used and are nonreturnable for refund exchange This does not limit the manufacturers warranty policies on any kit component This warranty gives you specific legal rights and you may also have other rights that vary from state to state Non Warranty Service If non warranty service is required the product may be sent to the Company for repair replacement transportation prepaid by calling 937 743 8248 for details complete instructions and service fee charges daytonaudio com 705 Pleasant Valley Dr DAYTONAUDIO tel 937 743 8248 Springboro OH 45066 info daytonaudio com USA OR A Dayton Audio Last Revised 11 18 2015
5. attery power becomes very low the front LED power indicator will flash for 30 seconds and the speaker will switch to standby mode Use the included power adapter to charge the speaker Charging The MARK1 is equipped with aan a built in battery only use the Fo supplied power adapter when an AC ADAPTER D charging The green LED indicator on the back of the speaker will flash while in charging mode 5 TROUBLESHOOTING NOTES e Ifthe Speaker can t be found in Bluetooth mode the speaker could be connected to another device Remove the device from any other devices and try again If you still can t find the Bluetooth speaker please turn off the speaker for 5 second then turn it back on e Bluetooth signal is intermittent the effective distance between speaker device is 30 feet the signal will be intermittent if the distance between the device and speaker is more than 30 feet e If your Bluetooth device is in search mode it may find many other Bluetooth devices please wait until the search is finished and select the MARK1 speaker to pair Don t hold the mobile device to close to the speaker when using the phone function to avoid echo NFC please make sure the mobile has NFC function and it is turned on in the device SPECIFICATIONS Operating temperature 0 C 55 C 32 F 131 F Amplifier output power Left Right 1 5Wx2 subwoofer 3 5Wx1 Amplifier input sensitivi
6. ty lt 400m V Amplifier SNR 2 70dB Frequency response 70Hz 20KHz Power voltage AC100 240V 50 60Hz DC 9V 1 5A Battery 7 4V 2000mAh Battery time 10hours Battery charging time 4 6hours Blue tooth range 7 10M 22 33 ft Bluetooth version 3 0 2 46 Support A2DP Warranty Information Dayton Audio products are warranted free from defects in material and workmanship for 5 years from date of purchase see exceptions below In the rare case of a product failure please contact your place of purchase or call our Customer Support Department at 937 743 8248 Warranty Limitations There are no other warranties either express or implied that extend the foregoing and there are no warranties of merchantability or fitness for any particular purpose Dayton Audio is not responsible for any consequential on inconsequential damage to any other unit or component or the cost for installation or extraction of any component of the audio system or for the improper use of products This includes but is not limited to burnt voice coils overheating bent frames holes in the cone or broken lead wires Warranty does not apply to misuse abuse neglect accident improper use etc Dayton Audio reserves the right to repair or replace the products with either a new or factory refurbished unit Exception Dayton Audio HDMI Cables No registration no questions asked LIFETIME warranty Replacement of Dayton Audio HDMI cables is with equal or better qu
Download Pdf Manuals
Related Search