Data sheets
Contents
1. B09966d SAUTER Right of amendment reserved 2015 Fr Sauter AG 3 1 93 070 Fr Sauter AG Im Surinam 55 CH 4016 Basel Tel 41 61 695 55 55 www sauter controls com 3 32. max 3 data points per picture e Configuring password and access rights e General settings contrast calibration reboot system info With the CASE TPC GZS100F599 parameterising software a separate interface pictures graphics lists can be created This makes user specific displays easier to create Connections for parameterisation The RJ 45 connection Ethernet and the DB9 interface EIA 232 are used for application downloads and firmware updates e The device is only for TN S network systems e Ethernet novaNet and COM are SELV PELV electrical circuits and must not be connected to ELV or TNV networks e For setting up fixed connections there must be an easily accessible isolating facility nearby This is class A equipment It may cause wireless interference in residential premises in this case the operator may be requested to implement appropriate measures For further information see the fitting instructions Disposal When disposing of the product observe the currently applicable local laws More information on materials can be found in the Declaration on materials and the environment for this product Dimension drawing 204 a 00000 O 05 To 185 Xi 8 B09964a Connection diagram RJ 11 6 6 RJ 45 DB 9 230 V novaNet Ethernet RS232
3. Product data sheet EY OP 250 Touch panel modu250 How energy efficiency is improved SAUTER EY modulo 2 tried and tested technology with a new design Features e Part of the SAUTER EY modulo 2 system family 93 070 e Graphic pressure sensitive operating and display unit for network wide operation of the automation stations AS e Menu guided user interface to visualise ASs and plants Alarm lists data point lists time switching programmes calendars and trend data EY OP250F001 e Change specified setpoints positioning values and digital positioning commands e Edit time switching programmes and calendars e Freely programmable graphic plant presentations with dynamic data points e Access rights with users created individually e Can be parameterised via CASE Suite languages applications e RJ 45 DB 9 interfaces for parameterisation and updating e RJ 11 interface for novaNet system bus Technical data Power supply Power supply 85 250 V 48 62 Hz Ambient conditions Power consumption lt 7W Operating temperature 0 45 C Storage and transport temperature 25 70 C Admissible ambient humidity Indicators display operation 10 80 rh no condensation Display 5 7 inches Resolution 320 x 240 pixels QVGA Active area W x H 140 x 105 mm Touch Resistive 4 wire Illumination Time controlled cut off Memory 8 MB flash 8 MB RAM Interfaces and
4. communication novaNet 1x RJ 11 socket Ethernet 1 x RJ 45 socket 10BaseT EIA 232 1 x DB9 connector Construction Dimensions WxHxD 204 x 156 x 46 mm Weight 1 kg Standards and directives Type of protection IP 20 EN 60529 Protection class EN 60950 1 Environment class Low voltage directive 2006 95 EC 3K3 IEC 60721 EN 60950 1 CE conformity as per EMC directive 2004 108 EC Overview of types Type Description EY OP250F001 Touch panel colour 256 colours EY OP250F002 Touch panel monochrome b w SAUTER Right of amendment reserved 2015 Fr Sauter AG EN 61000 6 1 EN 61000 6 2 EN 61000 6 4 EN 55022 Class A 3 1 1 3 Product data sheet 2 3 93 070 Accessories Software Type Description GZS100F599 CASE Tools CD latest version CASE TPC CASE HWC CASE Sun novaNet292 SW 7001064001 User manual German Connecting cables Type Description 0367862001 Automation station to modu250 1 5 m 0367862002 Automation station to modu250 2 9 m 0367862003 Automation station to modu250 6 0 m General information Type Description 0374494001 Stylus set for modu250 0374509001 Connector 3 pin packaged 0374515001 Set to extend degree of protection IP 65 incl seal 0374680001 0374680001 Seal single for set 0374515001 Additional information Fitting instructions P100002332 Declaration on materials and the environment MD 93 070 Descri
5. g is 31999 If the touch panel is connected directly to the moduFlex universal controller via point to point module 0374448001 the max admissible cable length is 6 m Special standards such as IEC EN 61508 IEC EN 61511 IEC EN 61131 1 and 2 were not taken into account Local requirements regarding installation usage access access rights accident prevention safety dismantling and disposal must be taken into account Furthermore the installation standards EN 50178 50310 50110 50274 61140 and similar must be observed LED indicators Above the display of the touch panel there are LEDs displaying the following information e The middle LED flashes green if the power supply is correct e The LED on the outer left flashes red when an alarm is active in an opened application 3 1 SAUTER Right of amendment reserved 2015 Fr Sauter AG Product data sheet Operation Operation is entirely by touching the display directly whereby the configuration data points of the AS are read automatically in Plug amp Play mode and can be managed without any additional parameterisa tion e Displaying and selecting the applications direct access to the automation stations e Displaying measured values alarms and statuses outputting positioning commands analogue and digital max 200 data points per station or plant e Displaying and changing time and holiday programmes as well as date and time e Reading and displaying historical data
6. ption of operation The modu250 touch panel is used for the graphical display navigation and operation of the automa tion station AS and its plants on site Intended use This product is only suitable for the purpose intended by the manufacturer as described in the De scription of operation section All related product documents must also be adhered to Changing or converting the product is not ad missible Engineering notes Fitting and power supply The touch panel is mounted on a top hat rail or directly on the front of a control cabinet The power supply with 85 240 V AC is connected via a pluggable connection terminal with an earth conductor Connection may only be performed when the system is disconnected from the electrical supply When commissioning the device you must remove the protective film on the front otherwise the readability of the display and the touch function may be negatively affected The communication wiring must be carried out correctly and in accordance with standards EN 50174 1 2 and 3 Communication wires must be kept separate from other live wires Data line Through direct connection to the novaNet network RJ 11 socket it is possible to access all connec ted ASs The number of communicating AS stations per touch panel must not be greater than 100 Every touch panel in the novaNet network requires a unique address between 31744 and 31799 comparable with PC subscribers the factory settin
Download Pdf Manuals
Related Search