Manual Cover Pages
Contents
1. coe USER S MANUAL version 1 1 CDB 6500AC DOORBELL AND PUSH BUTTON TRANSMITTER CDB 6500AC DOORBELL AND PUSH BUTTON TRANSMITTER Ding Dong Gong Doorbell button G Battery A Indicator D Indicator H Letter code selector B Letter code selector E Name plate l Mounting hardware C Loudspeaker F Push button CDB 6500AC DOORBELL AND PUSH BUTTON TRANSMITTER co E 1 Place a coin in the notch in the lower right 2 Install a battery and turn the letter selector to corner Carefully twist to separate the two halves the desired letter house code A Do not damage the rubber seal when separating or attaching the two halves CDB 6500AC DOORBELL AND PUSH BUTTON TRANSMITTER 8a Mount the back with the UP arrow pointing 3b 1 Place the double sided tape vertically at upward Install the screws through the two both ends of the back mounting points 2 Mount it at the desired location with the UP arrow pointing upward A The rubber rings are intended to provide a waterproof seal If you are in doubt about the A It is preferable to mount the product with waterproof seal apply silicone caulk screws 3a CDB 6500AC DOORBELL AND PUSH BUTTON TRANSMITTER 4 Press the front with push button onto the back A The two halves can only be joined when the notches in the lower right corners match Make sure the seal ring is positioned correctly between the two halves 5 Write your name on the2. A Hoekstra managing director Zevenbergen 2008 01 30
3. name plate Carefully place it in the clear name plate holder Firmly snap both ends of the holder onto the doorbell A To remove the holder use a small flat screwdriver and pry both ends of the holder CDB 6500AC DOORBELL AND PUSH BUTTON TRANSMITTER co amp 0 6 Set the letter code selector to the same house 7 Plug the gong into any mains socket in your code as the doorbell 2 home The indicator lights up A You can move the gong to a different socket at any time without having to set the code again CDB 6500AC DOORBELL AND PUSH BUTTON TRANSMITTER co a Remarks A Reminders e This wireless product is a combination of a transmitter doorbell button and a receiver gong e The wireless doorbell system can be expanded indefinitely with suitable COCO products such as CDB 6500C separate gong CDB 6500BC built in transmitter and gong and PIR 2050 motion sensor e If the product does not work or does not work properly Check the correct placement and or function of the battery of the doorbell button replace if necessary Check whether the house codes of the doorbell transmitter and gong receiver match Someone nearby may be using the same house code Set the system to a different house code Check whether there is power at the mains socket to which the gong is connected the indicator must be lit A Safety instructions e Never use COCO products for life support systems or other applications in which
4. equipment malfunctions can have life threatening consequences e Do not attempt to repair this product If the product is damaged or if you are in doubt about the proper operation take the complete product back to the place of purchase e Remove the battery from the doorbell button if the product will not be used for an extended period e Only use a dry cloth to clean the gong Power e Replace the battery if the indicator on the doorbell button no longer lights when the doorbell button is pressed e Only use a 12 Volt A23 alkaline battery e Do not throw the battery into an open fire e Respect the local regulations when disposing of batteries CDB 6500AC DOORBELL AND PUSH BUTTON TRANSMITTER EJI A Wireless e This product works using a radio signal that passes through walls windows and doors The range is maximum 75 metres in the open air The range indoors is strongly influenced by local conditions such as concrete glass and metals On average the indoor range is approximately 30 metres e New double glass often includes a thin metallic layer This type of glazing HR glass allows most visible light to pass through but has a negative impact on radio signals If there is HR glass between the transmitter and receiver you should expect a significant reduction of the range of the wireless signal e This product operates at a frequency of 433 92 MHz It complies with the essential requirements and other conditions of R amp TTE Di
5. rective 1999 5 EC and can be used in all EU countries e There may be restrictions on the use of this device outside the EU If this device is used outside the EU check whether the device complies with the local directives This product complies with the essential requirements and other relevant provisions of the applicable European directives The Declaration of Conformity DoC is available at www coco technology com be If possible submit this product for recycling after use Do not dispose of the product with household trash Warranty and copyright This device is covered by a 2 year warranty that begins on the day of purchase Visit www coco technology com warranty for additional information Reprinting of portions of this manual without permission from Pan Trade International B V is expressly prohibited CDB 6500AC DOORBELL AND PUSH BUTTON TRANSMITTER i ti PAN TRADE INTERNATIONAL B V P O BOX 126 4760 AC ZEVENBERGEN THE NETHERLANDS www coco technology com Declaration of Conformity Pan Trade International BV declares that the COCO product model type designation CDB 6500AC DOORBELL AND PUSH BUTTON TRANSMITTER item number 74023 is in compliance with the essential requirements and other relevant provisions of directives R amp TTE 1999 5 EC EMC 2004 108 EC and LVD 2006 95 EC and is compatible with the standards EN 300 220 1 3 EN 55015 and EN 301 489 1 3 Manufacturer Authorised representative Hae M
Download Pdf Manuals
Related Search