Home
QVIS TT-202 User`s Manual
Contents
1. is being transmitted When the sy stem is configured correctly LEDs on both modules should light simultaneously in red signaling a connection to take control of the camera s Check the if every thing works correctly and quality of the camera control e Upon completion of setup changes reset the device by disconnecting the power supply Specification Preparing modules for operation Itis recommended to perform the first start up and configuration setup within workshop conditions over short distances between devices This can save the valuable time in the configuration of TT 202 for various cameras used in video monitoring e Fix and direct the antenna in such a way to achieve clearest line of sight between the two Connect the RS485 wires appropriately to the modules terminals A B Connect the sources of signal control key board camera Connect the power adaptor to the telemetric modules then to the wall outlet The LED indicator on panel will indicate that the data is being transmitted When the sy stem is configured correctly LEDs on both modules should light simultaneously in red signaling a connection to take control of the camera s e Check the if every thing works correctly and quality of the camera control e Upon completion of setup changes reset the dev ice by disconnecting the power supply TT 202 Wireless Telemetric Modem Sometimes it is necessary to change t
2. original date of despatch of the defective Product s Any replaced Product s become the property of QVIS LABS 6 The warranty shall not cover any defect caused a By fair wear and tear b In whole or in part by the negligence of the Buyer or a User c By improper or unauthorised use of the Product s including any attempt to carry out repairs or modifications to the Product s d By causes external to the Product s 7 Failure by the Buyer to settle accounts rendered for Product s supplied will render the warranty null amp void 8 If the Buyer adds labels to any of the Product s the warranty will be invalidated Distributer QVIS HQ 36 New Lane Havant Hampshire PO9 2JL gt t Offers and information Fo rly www adata co uk Customer services sales adata co uk QVIS www adata co uk TT 202 Wireless Telemetric Modem TT 202 is designed for wireless control of high speed cameras ov er the radio link on ISM 869 MHz band It supports 10 channels within the 869 4 to 869 65 MHz frequency band Each channel has a factory defined operating frequency It has both the bi directional RS485 and RS232 interfaces and designed for operation in Point Multipoint configuration Contents of TT 202 package e Bi directional telemetric module with RS485 RS232 and TTL port e Stub omnidirectional antenna up to 6km distance Users Manual This telemetric sy stem has been created for the demands of professional C
3. the warranty 4 Repairs undertaken by QVIS LABS under the terms of its warranty are guaranteed for 90 days from the date of dispatch to the Buyer 5 Where QVIS LABS inits absolute discretion replaces any defective Product s the warranty on such replacement Product s shall continue in effect for the remainder of the unexpired term of the warranty commencing from the original date of despatch of the defective Product s Any replaced Product s become the property of QVIS LABS 6 The warranty shall not cover any defect caused a By fair wear and tear b In whole or in part by the negligence of the Buyer or a User c By improper or unauthorised use of the Product s including any attempt to carry out repairs or modifications to the Product s d By causes external to the Product s 7 Failure by the Buyer to settle accounts rendered for Product s supplied will render the warranty null amp void 8 If the Buyer adds labels to any of the Product s the warranty will be invalidated Distributer QVIS HQ 36 New Lane Havant Hampshire PO9 2JL gt t Offers and information Phang www adata co uk Customer services sales adata co uk VIS ometi www adata co uk TT 202 Wireless Telemetric Modem TT 202 is designed for wireless control of high speed cameras ov er the radio link on ISM 869 MHz band It supports 10 channels within the 869 4 to 869 65 MHz frequency band Each channel has a factory defined operatin
4. CTV systems with high speed cameras and recorders where stable and unattended control over radio links is required There is apossibility of using up to 10 independent operating channels with very high transmission quality making the TT 202 very suitable for almost all monitoring high demand sys tems with high speed cameras and industrial automatic control sy stems Qvis gives a warranty of 24 months General terms and conditions of a warranty 1 QVIS LABS warrants that the Product s shall be of satisfactory quality within the meaning of the Sale of Goods Act 1979 be reasonably fit for purpose and free from defects in materials or worknanship The period of such warranties shall be as set inthe price list that is current at the date of despatch of the Product s and the warranty period shall commence on the date of despatch of the Product s 2 Any alleged defects in the Product s must be notified in writing within 14 days of receipt of the Product s 3 In the event of any established breach of warranty QVIS LABS shall repair or replace in its absolute discretion any defective Product s The Buyer shall be liable for the delivery charges incurred in returning the defective Product s to QVIS LABS but shall not be liable for the cost of repair or replacement or the delivery charge for returning the repaired or replaced Product s to the Buyer If QVIS LABS complies with this clause then it shall have no further liability for breach of
5. Qvis gives a warranty of 24 months General terms and conditions of a warranty 1 QVIS LABS warrants that the Product s shall be of satisfactory quality within the meaning of the Sale of Goods Act 1979 be reasonably fit for purpose and free from defects in materials or workmanship The period of such warranties shall be as set inthe price list that is current at the date of despatch of the Product s and the warranty period shall commence on the date of despatch of the Product s 2 Any alleged defects in the Product s must be notified in writing within 14 days of receipt of the Product s 3 In the event of any established breach of warranty QVIS LABS shall repair or replace in its absolute discretion any defective Product s The Buyer shall be liable for the delivery charges incurred in returning the defective Product s to QVIS LABS but shall not be liable for the cost of repair or replacement or the delivery charge for returning the repaired or replaced Product s to the Buyer If QVIS LABS complies with this clause then it shall have no further liability for breach of the warranty 4 Repairs undertaken by QVIS LABS under the terms of its warranty are guaranteed for 90 days from the date of dispatch to the Buyer 5 Where QVIS LABS inits absolute discretion replaces any defective Product s the warranty on such replacement Product s shall continue in effect for the remainder of the unexpired term of the warranty commencing from the
6. g frequency It has both the bi directional RS485 and RS232 interfaces and designed for operation in Point Multipoint configuration Contents of TT 202 package e Bi directional telemetric module with RS485 RS232 and TTL port e Stub omnidirectional antenna up to 6km distance Users Manual This telemetric sy stem has been created for the demands of professional CCTV systems with high speed cameras and recorders where stable and unattended control ov er radio links is required There is a possibility of using up to 10 independent operating channels with very high transmission quality making the TT 202 very suitable f or almost all monitoring high demand sys tems with high speed cameras and industrial automatic control sy stems Specification Preparing modules for operation Itis recommended to perform the first start up and configuration setup within workshop conditions over short distances between devices This can save the valuable time in the configuration of TT 202 for various cameras used in video monitoring Fix and direct the antenna in such a way to achieve clearest line of sight between the two Connect the RS485 wires appropriately to the modules terminals A B e Connect the sources of signal control key board camera e rate the power adaptor to the telemetric modules then tothe TT 202 Wireless Telemetric Modem wall outlet The LED indicator on panel will indicate that the data
7. he basic parameters of the transmission protocol as well as the operating channels Please use the table below To set the basic parameters of telemetric protocols of cameras or recorders use Dip switches It works among others with the f ollowing protocols PELCO D PELCO P SAMSUNG COP 2 Santachi PANASONIC Longcomity HUND A600 LILIN VICON MOLYNX KALATEL VCL Reserved COP 1 Ultrak Dynacolor Dip switch settings Dip switch 2 3 4 5 setting of operating channel Dip switch 8 parity check 8E1 0 8N1 1 Pelco Dip switch 6 7 baudrate NOTE Readout of Dip switch positions are executed when the switching power on Thats why changes to the switch settings are to be made with power switched off Sometimes in case of bidirectional protocol it is necessary to short the pins 1 and 2 on J3 terminal strip using computer ty pe jumper An access to this strip is only possible after removal of upper metal casing Operating channel settings switches 2 3 4 5 easel 2 4 TIE 2 34 5 g69 4375 59 2 34 5 agggars 2 3 4 5 ge9 5125 z a a i z q janat jana sa s 10 24a 4 5 369 5625 23 4 5 a69 6125 2 3 4 5 69 6375 Parity bit settings Baudrate settings switches 6 7 switch amp i m 1200 n 2400 8N1 None a7 bps a7 bps A 4800 A 9600 67 bps 67 bps Bits Even Sometimes it is necessary to change the basic para
8. meters of the transmission protocol as well as the operating channels Please use the table below To set the basic parameters of telemetric protocols of cameras or recorders use Dip switches It works among others with the f ollowing pro tocols PELCO D PELCO P SAMSUNG COP 2 Santachi PANASONIC Longcomity HUND A600 LILIN VICON MOLYNX KALATEL VCL Reserved COP 1 Ultrak Dynacolor Dip switch settings Dip switch 2 3 4 5 setting of operating channel Dip switch 8 parity check 8E1 0 8N1 1 Pelco Dip switch 6 7 baudrate NOTE Readout of Dip switch positions are executed when the switching power on Thats why changes to the switch settings are to be made with power switched off Sometimes in case of bidirectional protocol it is necessary to short the pins 1 and 2 on J3 terminal strip using computer ty pe jumper An access to this strip is only possible after removal of upper metal casing Operatiag channel settings switches 2 3 4 5 i afl 4 a a 5 2 34 8 aggaars 2 3 4 5 gg 5125 g E T aaa 7 frees 8 atta Q s5 5 10 z 34 5 89 5625 2 3 4 5 859 5675 2 3 4 5 ene 2 34 5 69 6375 Parity bit settings Baudrate I switches 6 7 switch 8 1200 a i 2400 bps bps z 4800 9600 Even a7 bps a7 bps For more information about our wireless transmission kits and all other available products please vi
9. sit our website www adata co uk Alternativ ely scan this QR code with y our smart phone to be directed instantly to our website For more information about our wireless transmission kits and all other available products please visit our website www adata co uk Alternativ ely scan this QR code with y our smart phone to be directed instantly to our website
Download Pdf Manuals
Related Search
Related Contents
Embedded Linux 2.6 User Manual 1Copyright Projet GREP Plan d`assurance qualité HP tx2-1305au External Devices Guide Mode d`emploi du cours Lou Bouïarguié - Septembre 2012 intext:Betriebsanleitung filetype:pdf Manuel utilisateur chaîne 11 vitesses Manual Copyright © All rights reserved.
Failed to retrieve file