LG Digital Signage
Contents
1. B LG Life s Good OWNER S MANUAL LG Digital Signage MONITOR SIGNAGE Please read this manual carefully before operating the your set and retain it for future reference 42SH7DB 49SH7DB 55SH7DB www lg com HSMDNA TABLE OF CONTENTS 10 10 11 12 13 15 17 17 18 18 18 20 21 24 SAFETV PRECAUTIONS Precautions In Installing the Product Precautions to the AC Adapter and Electrical Power Precautions In Moving the Product Precautions In Using the Product Mounting on a Wall LICENSES ASSEMBLV AND PREPARATION Optional Accessories Parts and Buttons Connecting the Stand Connecting the Speakers Connecting IR 8 Light Sensor Portrait Lavout Attaching and Removing the LG Logo Bracket Installing on a Wall REMOTE CONTROL Displaving the Device Name Connected to an Input Port White Balance Adjust Menu MAKING CONNECTIONS Connecting to a PC External Device Connection Daisv Chain Monitors TROUBLESHOOTING PRODUCT SPECIFICATIONS Safetv precautions Please read these safety precautions carefully before using the product A WARNING If you ignore the warning message you may be seriously injured or there is a possibility of accident or death N CAUTION If you ignore the caution message you may be slightly injured or the product may be damaged A WARNING Indoor Use Only Precautions In Installing the Product A WARNING Keep away from heat2. and to the wall installation instructions are available from your l 1 Use only screws and wall mounting brackets dealer see the optional Tilt Wall Mounting Bracket Installation and Setup Guide that conform to VESA standards 2 Screws which are longer than standard length mav damage the inside of the monitor 3 Anon VESA standard screw may damage the product and cause the monitor to fall LG Electronics is not liable for any accidents related to the use of non standard screws jil ti A Please use VESA standard as below e 785 mm and above 10cm 10cm Fixing screws Diameter 6 0 mm x Pitch 1 0 mm x Length 12 mm 785 mm N CAUTION Disconnect the power cord before moving or installing the monitor to avoid risk of electric shock If you install the monitor on a ceiling or slanted wall it may fall and result in injury Use an authorized LG wall mount and contact your local dealer or qualified personnel to assist with the installation Do not over tighten the screws as this may damage the monitor and void your warranty e Use only screws and wall mounting brackets that meet the VESA standard Any damage or injuries caused by misuse or use of improper accessories are not covered by the warranty To prevent injury this apparatus must be securely attached to the wall in accordance with the installation instructions This pertains only to Australia and New Zealand Q NOTE The wall mount kit includes the instal
3. power AC 100 240 V 50 60 Hz 1 2 A Power consumption On Mode 110 W Typ Sleep Mode DISPLAYPORT lt 0 7 W Sleep Mode HDMI DVI D RGB lt 1 0 W Off Mode lt 0 5W Dimensions Width Head 948 7 mm x 555 3 mm x 31 7 mm 12 5 kg x Height x Depth Head Stand 948 7 mm x 617 7 mm x 298 3 mm 13 9 kg Weight Head Speaker 948 7 mm x 555 3 mm x 81 3 mm 13 3 kg Head Speaker Stand 948 7 mm x 617 7 mm x 298 3 mm 14 7 kg 49SH7DB LCD screen Pixel pitch 0 55926 mm H x 0 55926 mm V Power Rated power AC 100 240 V 50 60 Hz 1 6A Power consumption On Mode 125 W Typ Sleep Mode DISPLAYPORT lt 0 7 W Sleep Mode HDMI DVI D RGB lt 1 0 W Off Mode lt 0 5 W Dimensions Width Head 1094 6 mm x 637 4 mm x 31 7 mm 15 6 kg x Height x Depth Head Stand 1094 6 mm x 699 7 mm x 298 3 mm 17 0 kg Weight Head Speaker Head Speaker Stand 1094 6 mm x 637 4 mm x 81 3 mm 16 4 kg 1094 6 mm x 699 7 mm x 298 3 mm 17 8 kg m Z ep bs i as HSMDNA 26 55SH7DB LCD screen Pixel pitch 0 630 mm H x 0 630 mm V Power Rated power AC 100 240 V 50 60 Hz 1 7 A Power consumption On Mode 140 W Typ Sleep Mode DISPLAYPORT lt 0 7 W Sleep Mode HDMI DVI D RGB lt 1 0 W Off Mode lt 0 5W Dimensions Width x Height x Depth Weight Head Head Stand 1230 4 mm x 713 7 mm x 31
4. 7 mm 20 7 kg 1230 4 mm x 776 1 mm x 298 3 mm 22 1 kg Head Speaker 1230 4 mm x 713 7 mm x 81 3 mm 21 5 kg Head Speaker Stand 1230 4 mm x 776 1 mm x 298 3 mm 22 9 kg 27 HDMI OPS DVI D DISPLAYPORT PC RGB PC Support mode Resolution Horizontal Vertical frequency kHz frequency Hz 720 x 400 31 468 70 8 640 x 480 31 469 59 94 800 x 600 37 879 60 317 1024 x 768 48 363 60 1280 x 720 44 772 59 855 1280 x 960 60 60 1152 x 864 57 717 59 934 1280 x 1024 63 981 60 02 1920 x 1080 67 5 60 Support Mode At Pipa jet eed frequency 640 x 480 31 469 59 94 800 x 600 37 879 60 317 1024 x 768 48 363 60 1280 x 720 44 772 59 855 1366 x 768 47 7 60 1280 x 1024 63 981 60 02 1680 x 1050 65 290 59 954 1920 x 1080 67 5 60 HDMI OPS DISPLAYPORT DTV Support Mode Re fi Salaam ae frequency 480 60P 31 5 60 576 50P 31 25 50 720 50P 37 5 50 720 60P 45 60 1080 50i 28 1 50 1080 60i 33 75 60 1080 50P 56 25 50 1080 60P 67 5 60 Q NOTE PC resolutions available for the Input Label option in RGB HDMI OPS DVI D DISPLAYPORT input modes 640 x 480 60 Hz 1280 x 720 60 Hz 1920 x 1080 60 Hz 480p 720p and 1080p DTV resolutions Vertical frequency The product display functions by the screen image changing dozens of times every second like a fluorescent
5. TE For the best image quality using the monitor with HDMI connection is recommended To comply with the standard specifications of the product use a shielded interface cable with a ferrite core such as a DVI cable If you turn the monitor on when the set is cold the screen may flicker This is normal Sometimes red green or blue spots may appear on the screen This is normal Use a High Speed HDMIS M cable Use a certified cable with the HDMI logo attached If you do not use a certified HDMI cable the screen may not display or a connection error may occur Recommended HDMI Cable Types High Speed HDMI Cable High Speed HDMI Cable with Ethernet If you cannot hear any sound in HDMI mode please check your PC settings Some PCs require you to manually change the default audio output to HDMI If you want to use HDMI PC mode you must set your PC DTV to PC mode You may experience compatibility issues if you use HDMI PC mode Make sure the power cable is disconnected If you connect a gaming device to the monitor use the cable provided with the gaming device It is recommended to use the speakers that are provided as optional accessories High Speed HDMI cables transmit a HD signal up to 1080p and higher Use the standard Macintosh adapter since an incompatible adapter is available in the market Different signaling system Apple computers may require an adapter to connect to this monitor Call or visit their
6. aved Problem Action Is the product power cord connected2 e Check if the power cord is correctly plugged into the power outlet Does the Out of range message appear e The signal from the PC video card is out of the vertical or horizontal frequency range of the product Adjust the frequency range by referring to the Specifications in this manual Maximum resolution 1920 x 1080 60 Hz Does the No Signal message appear e The signal cable between PC and product is not connected Check the signal cable e Press the INPUT menu in the remote Control to check the input signal The Unknown Product message appears when the product is connected Problem Action Did you install the driver e Check if the Plug amp Play function is supported by referring to the video card user manual The screen image looks abnormal Problem Action Is the screen position wrong e Check if the video card resolution and frequency are supported by the product If the frequency is out of range set to the recommended resolution in the Control Panel Display Setting menu The screen is displayed abnormally e The proper input signal is not connected to the signal port Connect the signal cable that matches with the source input signal After image appears on the product Problem Action After image appears when the product is turned off e If you
7. enon is referred to as image sticking HSMDNA 24 PRODUCT SPECIFICATIONS The product specifications below mav be changed without prior notice due to upgrade of product functions TANA refers to alternating current AC and refers to direct current DC LCD screen Screen tvpe Thin Film Transistor TFT Liquid Crvstal Displav LCD Screen Video signal Maximum resolution 1920 x 1080 60 Hz This may not be supported on some OS or graphic card types Recommended 1920 x 1080 60 Hz resolution This may not be supported on some OS or graphic card types Horizontal frequency RGB 30 kHz to 83 kHz HDMI OPS DVI D DISPLAYPORT 28 1 kHz to 83 kHz Vertical frequency RGB 50 Hz to 75 Hz HDMI OPS DVI D DISPLAYPORT 50 Hz to 60 Hz Synchronization Separate Sync Digital Input Output ports SPEAKER OUT AUDIO IN OUT LAN PIXEL SENSOR HDMI IR amp LIGHT SENSOR DP IN OUT DVI D USB RGB RS 232C IN OUT Embedded battery Applied Environmental Operating Temperature 0 C to 40 C Conditions Operating Humidity 10 to 80 Storage Temperature 20 C to 60 C Storage Humidity 5 to 95 Applicable only for models that support the speakers Audio AUDIO RMS Audio Output 10 W 10 W R L Input Sensitivity Speaker Impedance 0 7 Vrms 80 42SH7DB 25 LCD screen Pixel pitch 0 4833 mm H x 0 4833 mm V Power Rated
8. he display Do not let the product fall or drop when connecting it with an external device D This may cause injury and or damage to the product e When connecting it to a game device keep a distance of four times the diagonal measurement of the screen from the device gt If the product falls because of the short cable this may cause injury and or damage to the product Leaving a fixed image on the screen for a long time may cause damage to the screen and cause image burn in To use the product for along period of time use a screen saver on the PC or utilize the residual image prevention function on the product and when the product is not used turn off the power Burn in and related problems are not covered by the warranty on this product Do NOT install this product on a wall where there is high risk of exposure to oil fumes or mist gt This may damage product and cause it to fail AN CAUTION Make sure the product ventilation holes are not blocked Install the product in a suitably wide place more than 10 cm from the wall gt If you install the product too close to the wall it may be deformed or fire can break out due to internal heat Do not block the ventilation hole of the product by a tablecloth or curtain The product can be deformed or fire can break out due to overheating inside the product nstall the product on a flat and stable place that has no risk of dropping the product If the prod
9. lamp The vertical frequency or refresh rate is the number of image displays per second The unit is Hz Horizontal frequency The horizontal interval is the time taken to display one horizontal line When 1 is divided by the horizontal interval the number of horizontal lines displayed every second can be tabulated as the horizontal frequency The unit is kHz DISPLAYPORT does not support YCbCr 4 2 2 m Z ep a N T ENERGY STAR is a set of power saving guidelines issued by the U S Environmental Protection Agency EPA has determined that this product meets rae the ENERGY STAR guidelines for energy rerit efficiency Refer to ENERGY STAR gov for more ENERGY STAR information on the ENERGY STAR program MODEL SERIAL As an ENERGY STAR Partner LGE U S A Inc LG Life s Good Make sure to read the Safetv Precautions before using the product The model and serial numbers of the SET are located on the back and one side of the SET Record it below should vou ever need service WARNING This is a class A product In a domestic environment this product mav cause radio interference in which case the user mav be required to take adequate measures Temporarv noise is normal when powering ON or OFF this device
10. lation guide and all necessary parts The wall mounting bracket is optional You can obtain additional accessories from your local dealer The length of screws required may differ depending on the wall mount Be sure to use the correct length For more information please refer to the guide provided with the wall mount HSMDNA 14 Securing the monitor to a wall optional Procedure may differ depending on the model MA WARNING Insert and tighten the evebolts or brackets and bolts on the back of the monitor If there are already bolts inserted in the eyebolts position remove the other bolts first Mount the wall brackets with the bolts to the wall Match the location of the wall bracket and the eyebolts on the rear of the monitor Connect the eyebolts and wall brackets tightly with a sturdy cord Make sure the securing cord is horizontal with the flat surface If the monitor is not positioned in a sufficiently stable location there is a danger that it will fall Many injuries particularly to children can be avoided by taking simple precautions such as N caution Using cabinets or stands recommended by the manufacturer Only using furniture that can safely support the monitor Ensuring the monitor is not overhanging the edge of the supporting furniture Not placing the monitor on tall furniture for example cupboards or bookcases without anchoring both the furniture and the monitor to a suitable s
11. level of red The higher 17 m Z ep be n AL the number the redder the set Decrease the number if the screen looks too red G Gain Adjusts the level of green The higher the number the greener the set Decrease the number if the screen looks too green B Gain Adjusts the level of blue The higher the number the bluer the set Decrease the number if the screen looks too blue Backlight Adjusts the brightness The higher the number the brighter the set This works in the same way as the backlight of the user menu Reset Resets the white balance value to the factory settings HSMDNA 18 MAKING CONNECTIONS Vou can connect various external devices to vour monitor Change the input mode and select the external device vou want to connect For more information about external device connections see the user manual provided with each device Connecting to a PC Some of the cables are not provided This monitor supports the Plug amp Plav feature Plug amp Play a feature that enables a PC to recognize devices attached by the user without device configuration or user intervention when powering up External Device Connection Connect a HD receiver DVD or VCR player to the monitor and select an appropriate input mode Some of the cables are not provided For the best picture and sound quality connecting external devices to your monitor using HDMI cables is recommended 19 B NO
12. nsumption INPUT Selects the input mode 3D Used for viewing 3D videos This model does not support this 1 a A Toggles between numerical and alphabetical Depending upon the model this feature mav not be supported Number and Alphabet buttons Enters numerical or alphabetical characters depending upon the setting Depending upon the model this feature mav not be supported CLEAR Deletes the entered numerical or alphabetical character Depending upon the model this feature mav not be supported 000 Volume Up Down Button Adjusts the volume ARC Selects the Aspect Ratio mode AUTO Automatically adjusts picture position and minimizes image instability available for RGB input only Depending upon the model this feature may not be supported MUTE Mutes all sounds BRIGHTNESS Adjust the brightness by pressing the Up and Down buttons on the remote control In USB mode the OSD menu has the Page function to move to the next file list Depending upon the model this feature may not be supported 16 m Z ep 2 ale ME MUTE J PSM Selects the Picture Mode e INFO Views the information of the currently program and the screen H W BAL Enters the White Balance menu ug SETTINGS Accesses the main menus or saves your input and exit menus ji 79 S MENU SuperSign menu key Depending upon the model this feature may not be supported Navigation Buttons Scrolls through men
13. odels only e Please turn off the power before removing the TAMA The image may be different according to the cable Connecting or removing the speaker x model cable while turned on may result in no sound 1 Connect an input signal cable before installing the speakers Connecting IR amp Light Sensor When you connect the cable to the product the feature for receiving remote control signals is d activated The IR amp light sensor is magnetic Attach it to the front edge of the product for use Cecooosjja O O A 2 Mount the speakers by using screws as shown below Make sure the power cable is Front disconnected before making a connection O O 3 Connect the speaker cables noting the correct polaritv Use cable holders and cable ties to organize the speaker cables Q note e The signal strength of the IR and Light sensor will decrease if the sensor is not placed in front of the product Portrait Lavout When installing in a portrait lavout rotate the monitor counterclockwise 90 degrees when facing the screen r b Using Kensington Lock This is not available for all models The Kensington security system connector is located at the back of the monitor For more information on installation and use of this system refer to the manual provided with the Kensington security system or visit http www kensing
14. our registration code in the DivX VOD section of your device setup menu DivX Certified to play DivX video up to HD 1080p including premium content DivX DivX Certified and associated logos are trademarks of DivX LLC and are used under license Covered by one or more of the following U S patents 7 295 673 7 460 668 7 515 710 7 519 274 DOLBY Manufactured under license from Dolby Laboratories Dolby and the double D DIGITAL PLUS symbol are trademarks of Dolby Laboratories Q note The warranty will not cover any damage caused by using the product in an excessively dusty environment ASSEMBLV AND PREPARATION N CAUTION Always use genuine components to ensure safety and product performance The product warranty will not cover damage or injury caused by the use of counterfeit components NOTE The accessories provided with your product may vary depending on the model or region Product specifications or contents in this manual may be changed without prior notice due to upgrade of product functions SuperSign Software amp Manual Downloading from the LG Electronics website Visit the LG Electronics website www lgecommercial com supersign and download the latest software for your model m z ep m n als Optional Accessories Without prior notice optional accessories are subject to change to improve the performance of the product and new accessories may be added The illustrations in thi
15. power cord make sure that it is certified by the applicable national standards when not provided by the supplier If the power cable is faulty in any way please contact the manufacturer or the nearest authorized repair service provider for a replacement Precautions In Moving the Product A WARNING Make sure to turn off the product You may be electrocuted or the product can be damaged e Make sure to remove all cables before moving the product gt You may be electrocuted or the product can be damaged e Make sure the panel faces forward and hold it with both hands to move If you drop the product the damaged product can cause electric shock or fire Contact an authorized the service center for repair Make sure the product is turned off unplugged and all cables have been removed It may take 2 or more people to carry larger apparatus Do not press against or put stress on the front panel of the apparatus N CAUTION Do not shock the product when moving it gt You may be electrocuted or the product can be damaged Do not dispose the product packing box Use it when you move Precautions In Using the Product A WARNING Do not disassemble repair or modify the product at your own discretion Fire or electric shock accident can occur Contact the service center for check calibration or repair e When the display is to be left unattended for an extended period of time unplug it from the wall outlet Keep the
16. product away from water gt Fire or electric shock accident can occur Do not shock or scratch the front and sides of the screen with metallic objects Otherwise it may cause damage to the screen Avoid high temperatures and humidity N CAUTION Do not put or store inflammable substances near the product There is a danger of explosion or fire due to careless handling of the inflammable substances When cleaning the product unplug the power cord and scrub gently with a soft cloth to prevent scratching Do not clean with a wet cloth or spray water or other liquids directly onto the product An electric shock may occur Do not use chemicals such as benzene paint thinners or alcohol Take a rest from time to time to protect your vision Keep the product clean at all times Take a comfortable and natural position when working with a product to relax the muscles Take a regular break when working with a product for a long time Do not press strongly upon the panel with a hand or sharp object such as nail pencil or pen or make a scratch on it Keep the proper distance from the product gt Your vision may be impaired if you look at the product too closely Set the appropriate resolution and clock by referring to the User s Guide gt Your vision can be impaired Use authorized detergent only when cleaning the product Do not use benzene thinner or alcohol Product can be deformed Do not expo
17. s manual may differ from the actual product and accessories cO ab O cf Screws Diameter 4 0 mm x Pitch 0 7 mm x Length 10 mm including spring washer BB 8 8 b B 8 se GH B AA Speakers Cable Holders Screws Screws SP 2100 Cable Ties Diameter 4 0 mm x Diameter 4 0 mm x Pitch 0 7 mm x Length 8 mm Pitch 1 6 mm x including spring washer Length 10 mm Speaker kit HSMDNA OQ OQ CB KT OPSA Screws Connecting Cable Power Cord Card Easv Setup Guide AN WF500 KT SPO Wi Fi Dongle kit Pixel sensor kit 1 NOTE Cable holder Cable tie may not be available in some areas or for some models Optional accessories are available for some models If necessary please purchase them separately Pixel sensor is sold separately You can obtain additional accessories from your local retail store Parts and Buttons Connecting the Stand m Z The image may be different according to the For certain models only a model The image may be different according to the D model I 1 INPUT MENU AUTO SET I Buttons 9990909 INPUT Changes the input source MENU Accesses the main menus or saves your input and exits the menus A V Adjust the up and down lt gt Moves left and right AUTO SET Displays the current signal and mode 4 I Turns the power on or off 10 ry Connecting the Speakers NOTE 2 For certain m
18. se to dripping or splashing and do not place objects filled with liquids such as vases cups etc on or over the apparatus e g on shelves above the unit Batteries should not be exposed to excessive heat For example keep away from direct sunlight open fireplace and electric heaters Do NOT place non rechargeable batteries in charging device Using headsets earphones for a long time or listening loudly can cause damage to your hearing Spray water onto a soft cloth 2 to 4 times and use it to clean the front frame wipe in one direction only Too much moisture may cause staining m Z ep bs n AL Do not use products using high voltage around the Monitor e g a bug zapper Monitor may have malfunction as its electrical shock Mounting on a Wall Do NOT install this product by yourself as you may injure yourself or cause damage to product Please contact service personnel authorised by manufacturer LICENSES HSMDNA Supported licenses may differ by model For more information of the licenses visit www lg com H Lm The terms HDMI and HDMI High Definition Multimedia Interface and the HDMI Trek See NITlGNUUGINEENINEZRELEE logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries This DivX Certified device has passed rigorous testing to ensure it plays DivX video To play purchased DivX movies first register your device at vod divx com HD Find y
19. sources like electrical heaters gt Electrical shock fire malfunction or deformation may occur Keep the packing anti moisture material or vinyl packing out of the reach of children gt Anti moisture material is harmful if swallowed If swallowed by mistake force the patient to vomit and visit the nearest hospital Additionally vinyl packing can cause suffocation Keep it out of the reach of children Do not put heavy objects on the product or sit upon it gt If the product collapses or is dropped you may be injured Children must pay particular attention Do not leave the power or signal cable unattended on the pathway The passerby can trip or fall which can cause electrical shock fire product breakdown or injury Install the product in a neat and dry place Dust or moisture can cause electrical shock fire or product damage If you can smell smoke or other odors or hear a strange sound unplug the power cord and contact the service center gt If you continue to use without taking proper measures electrical shock or fire can occur If you dropped the product or the case is broken turn off the product and unplug the power cord gt If you continue to use without taking proper measures electrical shock or fire can occur Contact the service center Do not drop an object on or apply impact to the product Do not throw any toys or objects on the product screen It can cause injury to human problem to product and damage t
20. t A fire can break out due to overheating Do not touch the power plug with wet hands Additionally if the cord pin is wet or covered with dust dry the power plug completely or wipe dust off You may be electrocuted due to excess moisture If you don t intend to use the product for a long time unplug the power cable from the product gt Covering dust can cause a fire or insulation deterioration can cause electric leakage electric shock or fire Fix the power cable completely If the power cable is not fixed completely a fire can break out Do not insert a conductor like a metal chopstick into one end of the power cable while the other end is connected to the input terminal on the wall Additionally do not touch the power cable right after plugging into the wall input terminal gt You may be electrocuted The appliance coupler is used as the disconnect device Please make sure the device is installed near the wall outlet to which it is connected and that the outlet is easily accessible As long as this unit is connected to the AC wall outlet it is not disconnected from the AC power source even if the unit is turned off N CAUTION Be sure to keep the outlet AC adapter and pins of the power plug clean from dust and etc This may cause a fire Do not unplug the power cord while the product is in use Electrical shock can damage the product Use only the power cord supplied with the unit If you use another
21. ton com Connect the Kensington security system cable between the monitor and a table The Kensington security system is optional You can obtain additional accessories from most electronics retail stores 11 m Z ep be i AL HSMDNA 12 Attaching and Removing the LG Logo Bracket For certain models only The image may be different according to the model Removing the LG Logo Attaching the LG Logo on the right side 1 Lay a clean cloth on the floor and then put 1 Lay a clean cloth on the floor and then put the monitor on it with the screen face down the monitor on it with the screen face down Remove the two screws that secure the LG Remove the two screws that secure the LG Logo Bracket to the bottom of the rear side of Logo Bracket to the bottom of the rear side of the monitor using a screwdriver the monitor using a screwdriver 2 After removing the screws remove the LG 2 After removing the screws remove the LG Logo When re attaching the LG Logo follow Logo Attach the LG Logo Bracket with the two the process in reverse order P screws aligning it with the holes at the right side 13 Installing ona Wall To install your monitor on a wall attach a wall mounting bracket optional part to the back of the T monitor 2 For proper ventilation allow a clearance of 10 Make sure that the wall mounting bracket is D cm on each side and from the wall Detailed securely fixed to the monitor
22. ts may be changed without prior notice due to upgrade of the product functions N caution Image sticking does not occur when using constantly changing images but may occur when using a fixed image for an extended period of time Therefore it is recommended that you use the instructions below to decrease the likelihood of image sticking occurring when using a fixed image It is recommended that you change the screen at least once every 12 hours at the very minimum if done more frequently the prevention of image sticking is more effective Recommended operating conditions 1 Change the background and the character colors using the same time interval a When changing colors using complementary colors helps to prevent image sticking ID UPM 123 PW ITO or Mofi Pixel Layer 23 m z ep a N aE e Change the image using the same time interval Make sure that the characters or images before changing the image remain in the same location after changing the image What is image sticking When the LCD panel displavs a static image for an extended period of time it can cause a voltage difference between the electrodes that operate the liquid crystals When the voltage difference between the electrodes builds up over time liquid crystals have a tendency to remain aligned in one direction During this process a previously displayed image remains visible This phenom
23. uct is dropped you may be injured or the product may be broken nstall the product where no EMI occurs Keep the product away from direct sunlight The product can be damaged f you install the product in a place that does not meet the recommended conditions this may cause serious damage to the product s picture quality life cycle and appearance Please check with LG or a qualified installer before installing This caution applies to a place where there is an abundance of fine dust or oil mist chemical substances are used the temperature is very high or low the humidity is very high or the product is likely to remain turned on for a long period of time airport and train station failure to do so will invalidate the warranty Do not install the product in an area with poor ventilation e g on a bookshelf in a closet or outside and avoid placing on cushions or carpets In addition do not install it where there are heating objects such as lighting equipment m Z 7 is i As HSMDNA Precautions to the AC Adapter and Electrical Power A WARNING If water or any foreign substance goes inside the product TV Monitor power cord or AC adapter disconnect the power cord immediately and contact the service center Otherwise this may cause a fire or electric shock due to damage to the product Do not touch the power plug or AC adapter with wet hands If the pins of the plug are wet or dusty wipe and dr
24. upport Not placing cloth or other materials between the monitor and supporting furniture Educating children about the dangers of climbing on furniture to reach the monitor or its controls Make sure that children do not climb on or hang from the monitor Q NOTE e Use a platform or cabinet that is large and strong enough to support the monitor securely e Brackets bolts and cords are sold separately You can obtain additional accessories from your local retail store The illustration shows a general example of installation and may look different from the actual product 15 REMOTE CONTROL The descriptions in this manual are based on the buttons on the remote control Please read this manual carefully to use the monitor correctly m Z ep be i AL To install batteries open the batterv cover place batteries 1 5 V AAA matching B and terminals to the labels inside the compartment and close the batterv cover To remove the batteries perform the installation actions in reverse The illustrations mav differ from the actual accessories N caution Do not mix old and new batteries as this may damage the remote control Be sure to point the remote control toward the remote control sensor on the monitor D POWER Turns the monitor on or off MONITOR ON Turns the monitor on MONITOR OFF Turns the monitor off ENERGY SAVING 2 Adjusts the brightness of the picture to reduce energv co
25. us or options OK Selects menus or options and confirms your input BACK Allows you to move back one step in the user interaction function EXIT Quit all OSD tasks and applications _ M SIMPLINK Allows you to control various multimedia devices to enjoy multimedia simply by using the remote control through the SimpLink menu Depending upon the model this feature may not be supported TILE Selects the TILE Mode Ed PICTURE ID ON OFF When the Picture ID number matches the Set ID number you can control whichever monitor you want in multi display format USB Menu Control Buttons Controls media playback Displaving the Device Name Connected to an Input Port Display which devices are connected to which external input ports 1 Access the Input list screen and press the red input label button on the remote control 2 You can assign an input label for every input except USB Q note External inputs supported HDMI DVI D DISPLAYPORT OPS RGB Labels available PC DTV The input labels are displayed on the Input Label screen or at the top left of the screen when you change the external input setting For DTV PC compatible signals such as 1080p 60 Hz the screen settings may change according to the input label The Just Scan option is available if a PC is connected as an external device White Balance Adjust Menu Press the W BAL button on the remote control e R Gain Adjusts the
26. use a fixed image for a long time the pixels may be damaged Use the screen saver function e When a dark image is displayed on the screen after an image with high contrast black and white or gray this may cause image sticking This is normal for LCD screen products m Z ep m n as HSMDNA 22 The audio function does not work Problem Action No sound e See if the audio cable is connected properly e Adjust the volume e See if the sound is set properly Sound is too dull e Select the appropriate equalizer sound Sound is too low e Adjust the volume Screen color is abnormal Problem Screen has poor color resolution 16 colors Action e Set the number of colors to more than 24 bits true color Select Control Panel Display Settings Color Table menu in Windows Screen color is unstable or mono colored e Check the connection status of the signal cable Or re insert the PC video card Do black spots appear on the screen e Several pixels red green white or black color may appear on the screen which can be attributable to the unique characteristics of the LCD panel This is not a malfunction of the LCD The operation does not work normally Problem Action The power suddenly turned off e Is the Timer set e Check the power control settings Power interrupted Q NOTE The software related conten
27. web site for more information N caution Connect the signal input cable and tighten it by turning the screws clockwise Do not press the screen with your finger for a prolonged period as this may result in temporary distortion on the screen e Avoid displaying static images on the screen for a long period of time to prevent image burn Use a screensaver if possible A wireless communication device near your monitor can affect the image m z ep om n T HSMIDNA 20 Daisv Chain Monitors To use different products connected to each other connect one end of the signal input cable DP Cable to the DP Out connector of Monitor 1 and connect the other end to the DP In connector of the other product DP Cable Use a DP cable that is certified to DP1 1a SST or higher DVIIN DP OUT DP IN DP OUT DP IN DP IN DP OUT am Monitor 1 Monitor 2 Monitor 3 Monitor 4 Q NOTE If the signal is stable and there is no cable loss in general up to 100 monitors can be connected via the DP Out port at the recommended resolution If vou want to connect more than this number of monitors use a booster If you set the tile mode using DVI or HDMI you will not be able to watch HDCP encrypted content If the signal cable between the product and your PC is too long make sure to use the Booster or optical cable 21 TROUBLESHOOTING No image is displ
28. y them before use Otherwise this may cause a fire or electric shock Make sure to completely insert the power cord into the AC adapter gt If loosely connected the poor connection may cause a fire or electric shock Be sure to use power cords and AC adapters provided or approved by LG Electronics Inc gt The use of non approved products may cause a fire or electric shock When unplugging the power cord always pull it by the plug Do not bend the power cord with excessive force The power line can be damaged which may cause electric shock or fire Be careful not to step or place heavy objects electronic appliances clothing etc on the power cord or AC adapter Be careful not to damage the power cord or AC adapter with sharp objects gt Damaged power cords may cause a fire or electric shock Never disassemble repair or modify the power cord or AC adapter This may cause a fire or electric shock Make sure to connect the power cable to the grounded current You may be electrocuted or injured Use the rated voltage only The product can be damaged or you may be electrocuted In the presence of thunder and lightning never touch the power cord and signal cable because it can be very dangerous gt It can cause electric shock Do not connect several extension cords electrical appliances or electrical heaters to a single outlet Use a power strip with a grounding terminal designed for exclusive use with the computer g
Download Pdf Manuals
Related Search