iRFace Series Installation Guide
Contents
1. ccconnnnncnncccccnonananannnnnoconanannnnnons 21 SS IN VICE a E N 22 4 Check after Installation oooooccononnnoninanncannncnnnonananannnss 23 D ORNA i NRT EEE EAEN 24 FARES Ba e E A A T A 24 5 2 Ads mante DUON AA 25 Jo Ui TAS GIS USA A A 25 ARES DAI sa 26 I www BioTrackSoftware com BioFace Series Installation Guide 1 System Configuration 1 1 Notice about installing This product a mass produced product It strictly follows to the criteria of manufacture and inspection of China U S A and EU This file contains important information It is better for you to read it carefully prior to use If you ignore it the incorrect installation may cause the unit damage Although we could do our best to offer you service the neglect to the file could cause unwanted cost for you 1 Before installation please make sure the power is cut off because it is very dangerous if the power is on The short circuit of power cable may cause the core parts damage All exposed part of connection wire end can not be exceeded 5mm to prevent the bared wire accidental connection which leads to machine break down And also suggest using different colour cable to connect In the place where the static is strong or in winter please connect the grounding firstly in order to prevent the instant mass static damage the machine Connect power supply with device in the last for the wiring connecti2. i Face Series Installation Guide Version 1 2 1 Date Oct 2010 About this Guide This guide provides actual installation instructions only For information regarding user instructions please refer to BioFace Series User Manual www BioTrackSoftware com BioFace Series Installation Guide Content System congr atO iein dettedouesieactetcnaeausamsatceaan 1 Lol INGHCE about Stalin Aa l 1 2 Installation Environment occcconccnncnnccnnnnnccnnnnnocnnnnnnocnnnnnaccnnnnanoss 3 1 3 View of operation Pa oluinasinliaasbs ralla 4 2 The illustration of system construction oooooooocccccconononanannncnnoss 6 2 1 The illustration of system CONsStructl0N cccccccccnnccccnnnnnnonannonss 6 2 2 The sketch map Of COMMUNICATION ooocccccnnnnnnnnnnnnnnnnnnninadanononoss 7 3 IAS ION ra a sis 8 3 Ls Installation Ste pS uri OO iii 8 3 2 Conect with other devices omooccomo m AS 9 3 2 1 Door Sensor CONNECTION c occooooccccnccccccnnnononanananonononoss 11 3 2 2 Exit button CONNECTION oooccccccncccccccnononanananananonononoss 11 3 2 3 Time RING CONNectiON ccccccccnnnnnnnnananacananonoss 12 3 2 4 Door lock CONNectiON occcccccccnnnnnnnnnnannanononoss 13 3 2 5 Ethernet CONNectiON oooooooccccccccncconnnnnannnanaaannnonoss 17 3 210 R9232 CAMERON ias 18 3 2 1 RSEN OME ctio ii ios 19 3 2 8 Wiegand Output Connection ooooooooccccccconnnonnnco 20 3 2 9 Power CONNEeCtION
3. and negative terminal connection The unused bare end of wire should be cut off and use insulating tape to wrap it The delay time of strike lock is adjustable according to different conditions O When the Access Control System connected with Electric lock to prevent the self inductance EMF to affect the access control system you need to parallel one FR107 diode do not reverse the polarity Please use the equipped diode in the package Select electric lock it is better to use strike lock for the two direction opening glass door both open to inside or outside direction for the single opening wood door in company internal we recommend to use magnetic lock the magnetic lock also be called as electric magnetic lock The magnetic lock is more reliable than the strike lock but the strike lock is much safer than the magnetic lock In the small living community it is better to use strike lock and magnetic force lock The electric control lock gives out higher noise the electric control lock is commonly used to building communication Now there is a soundless electric control lock which is able to be applied Please pay attention the lock is made of iron and easy rust so you must beware of not exposing it 13 www BioTrackSoftware com BioFace Series Installation Guide to water or harsh condition there are some other electric locks available we don t recommend you to use them Connect with electric lock The Normal Open lo
4. ck is open when the power is on The Normal Close lock is closed when power is on The machine supports both of the two kinds of locks at the same time The way of lock connection changes with the type of lock For NO lock the NO terminal will be used for NC lock the NC terminal will be used This access control machine is powered by DC12V and work current 400mA If the lock work electric power is DC12V and the work current is less than 1000mA the fingerprint machine and lock are able to be powered by one adapter together please refer to table 1 2 In the following three cases we recommend that fingerprint machine and lock are powered separately 1 The working voltage of the lock is DC12V but the current difference of the fingerprint machine and the lock doesn t exceed 1A 2 The lock voltage is not DC12V 3 The distance between lock and fingerprint machine is too far 14 www BioTrackSoftware com BioFace Series Installation Guide NC LOCK DC12V Picture1 Power by one supply NO LOCK DC12V Picture2 power by one supply 15 www BioTrackSoftware com BioFace Series Installation Guide uN G DC12V PAY NC LOCK Picture 3 The terminal and lock powered by independent adapters Ss O DC12V i rd Lock Power na Y QoS sy a J ar y h Picture 4 The terminal and lock powered by independent adapters Note Please use the diode FR107 delivered with the equipment as the diode in
5. dicated in the figure above Be careful not to reverse its polarity 16 www BioTrackSoftware com BioFace Series Installation Guide 3 2 5 Ethernet connection The background PC software can communicate with device via TCP IP communication method to exchange data and remotely manage The terminal provide two ways connect Ethernet 1 The terminal connect with PC through cross cable IP 192 168 1 101 IP 192 168 1 100 Mask 255 255 255 0 Sub Mask 255 255 255 0 PC Face 2 The terminal connect with PC through network and HUB to create a local network PC EAS Switch 17 www BioTrackSoftware com BioFace Series Installation Guide 3 2 6 RS232 connection The background software can communicate with the equipment to upload and download records by the RS232 communication means Terminal connection definition Note Don t upload or download facial module through RS232 because the large data will effect the transfer speed 18 www BioTrackSoftware com BioFace Series Installation Guide 3 2 7 RS485 connection When the RS485 is used for networking the bus network architecture must be used for wiring Any RS485 communication line consists of a group of twisted pairs and signal is transferred with the help of the voltage difference between two communication lines However differential interference will arise between the two signal lines when signal is being transferred To eliminat
6. e differential interference add a bias resistor terminal matching resistor to the circuit It is unnecessary to add any terminal resistor in general except that the RS485 communication distance is over 100 meters In this case terminal matching resistors must be added to the terminal devices at both the start and end of the RS485 bus Terminal connection definition Terminal Function Note Don t upload or download facial module through RS485 because the large data will effect the transfer speed aS Sms a T 485B 485A 485B e RS485 T o RS485 Switch E CIS B La O y 19 www BioTrackSoftware com BioFace Series Installation Guide 3 2 8 Wiegand Output Connection The equipment provides standard Wiegand26 output which can be connected to most of the current access controller in the same way as connecting an IC reader or a password keyboard Generally it is preferable to limit the length of any connection line to an access controller within 90 meters A Wiegan signal extender can be used for a longer transmission distance or a place with strong interference Note 1 The distance between device and access controller or card reader shouldn t be over 90 meters If a longer distance is needed or there is interference in using environment please use Wiegand signal de lay 2 To ensure the stability of the Wiegand signal the device must share the GND with controller or Wiegand reade
7. er devices can work normally For more information please see the User Manual and Software Instructions 1 Upon power on the indicator begins to blank in green 2 Enter Menu gt Auto Check 3 Enter Menu gt User Management gt Add User gt Register Face to register a face template Test the access controller and its lock through face verification 4 Delete the registered face template if there is no problem 23 www BioTrackSoftware com BioFace Series Installation Guide 5 Others 5 1 Reset Due to operation error or other accidence which leads the machine not to work you can restart machine through reset key take a small tool which diameter is no more than 2mm 2 find reset mark of res on the left small hole on the bottom of device see following figure 3 Use the tool plug into the hole refer to the picture on right then plug out The machine is able to restar p Reset 24 www BioTrackSoftware com BioFace Series Installation Guide 5 2 Anti dismantle button Anti dismantle button is on middle of device whose function is realized by back cover pressing the anti dismantle button When the device is being dismantled it will send a alarm signal through the terminal Anti dismantle button 5 3 U flash disk using 1 there is a mini port of USB please see figure circle on the left 2 USB can be used to upload and download data by U disk 23 www BioTrackSoft
8. ery A Do Not use wire or other metal short the positive and negative terminal 28 www BioTrackSoftware com
9. exit button is installed for in door operation When the switch of the button is close the door will open The distance is approximately 1400mm from ground to exit button bottom Make sure that the exit button position is to align correct upright and the connection is accurate and reliable Unused exposed end of cable should be cut off and use insulating tape to wrap it Pay attention to electromagnetic disturbance For example The light switch the computer and so on 97 Door Sensor Button Power Supply _ La g F 11 www BioTrackSoftware com BioFace Series Installation Guide 3 2 3 Time Ring connection Connect the electrical bell to the fingerprint machine when arrive the appoint time the fingerprint machine will send signal to trigger relay The terminal supports both Normal Open bells and Normal Close bells at the same time DNormal Open bells Bawa ae 2 Normal Close bells BioFace Power supply BioBio 12 www BioTrackSoftware com BioFace Series Installation Guide 3 2 4 Door lock connection The way of installing door lock depends on the type of lock and local condition Internal resistor which comes from long distance transfer should be taken into consideration when selecting the cable of electric power The door lock should be installed reliable and stable Ensure the wiring is correct For the strike lock and electromagnetic lock you should pay attention to positive
10. not use the twisted pair or other type ferrules for the power wire When the power wire is choused you should consider attenuation of voltage which has passed long distance transfer 10 Please use specialized RS485 cable and the RS232 485 converter with power to hookup the network the bus structure apply to connect with each device When a long cable is used to transfer signal it is need to connect a matching resistance to 2 www BioTrackSoftware com BioFace Series Installation Guide receiver and its value is 1200 For other matters not covered in detail herein please refer to the User Manual Software Instructions and appendixes related to this equipment 1 2 Installation Environment Recommended location Install the BioFace indoors at least 10 feet 3m away from windows and 6 5 feet 2m away from light fixtures Preferable light intensity should range between 0 800 LUX 1200 Lux 0 800Lux NOT Recommended locations Direct sunlight Direct sunlight Indirect sunlight Too close to Outdoors thru wndow thru window light fixtures www BioTrackSoftware com BioFace Series Installation Guide 1 3 View of operation panel Front view Side view LED light TFT touch screen Fingerprint Sensor Baseline Integrated RF Card Module Read Section Touch Keypad Camera ON Reset key NAAA USB www BioTrackSoftware com BioFace Series Installation Guide Back view Batter
11. nt before the power of the device is cut down otherwise it is possible to damage the device badly Please follow instruction to connect peripheral equipment Door sensor connection Sensor GND Exit button connection Button GND Alarm connection NC2 COM2 NO2 Door lock connection NC1 COM1 NO1 Ethernet connection RJ45 1 RJ45 2 RJ45 3 RJ45 6 RS232 connection 232T 232R GND RS485 connection 485A 485B Wiegand output connection WD0 WD1 GND Power connection 12V GND 00400056000 Power TCP IP USB www BioTrackSoftware com BioFace Series Installation Guide The definition of terminal connection From left to right 1 NO2 Connect to Cable Bell mee together 5 For Door sensor and release Tie up button together Connect to Release button Connect to Lock RS485 communication Tie up cc ect 12 GND Connect to RS232 and Wiegand FeO tn RS232 communication together 15 WDO Wiegand out communication together SGND Connect to Power GND Tie up Connect to Power 12v together Tie up 10 www BioTrackSoftware com BioFace Series Installation Guide 3 2 1 Door sensor connection The door sensor is used to detect the door open close state terminal can monitor if the door has been unauthorized open through the door sensor at this time it can output a alarm signal moreover terminal can trigger prompt warning if the door is not close tightly 3 2 2 Exit button connection The
12. on If you find any unusual thing occur please firstly cut off the power then go to examine Keep in mind wiring operation under power on will lead to machine sudden damage we are not liable for damages and trouble due to such 1 www BioTrackSoftware com BioFace Series Installation Guide operation 5 After installation finish when go to test the exit door button please keep a personal in the outside because sometimes the accidental issue can bring on you are not able to go outside 6 Our equipment offer an automatically function please after the installing finish Run the auto test function to confirm the installation finish 7 We recommend using above the 12V 3A direct current supply for access control device electricity lock better to powered by 12VDC and no more than 1 5 A electric current At this time the electric current of supply should be above1A than lock power If the parameter of lock power surpasses this scope please connect technical personnel If the power had not met above requests it possibly causes to be unable normally to drive the electricity lock even damage the device 8 Before device to be connected please read and always follow Quick connect Guide closely Because the wrong wiring will cause the core block and sensor to burn out insult in device to break down at this cause we are not liable for any damages and trouble 9 If the space between power adapters and device is too long please do
13. r 3 If the distance of Wiegand output or 485 communication is over 90 meters in order to reduce the interference caused by the long distance it is suggested to use the cable with shield and connect the shield cable to the SGND terminal 20 www BioTrackSoftware com BioFace Series Installation Guide 3 2 9 Power Connection The device s working voltage is DC12V with working current 500mA standby current 50mA has provided two ways to connect power please select one referring to the actual 1 Terminal connection Make sure the connection as the Diagram Don t connect the poles in reverse 2 Slot connection Insert the plug of DC12V adapter into the power slot directly Power Slot N i AN 5 4 DC12V ars DC 12V Terminal connection Slot connection 21 www BioTrackSoftware com BioFace Series Installation Guide 3 3 Fix the device 1 Ensure to plug all the patch correctly 2 Hang the BioFace on the mounting plate top side first Please see figure 3 Then secure the BioFace to the mounting plate with a screw from below Please see figure 4 After installing the back cover ensure it will be stable solid and non loosening E 1 N 22 www BioTrackSoftware com BioFace Series Installation Guide 4 Check after Installation Upon completion of installation of the whole system check whether the installation is correct before power on Check whether the lock drive and oth
14. ware com BioFace Series Installation Guide USB Port 5 4 Reserve Battery Work principle Before use make sure the reserve battery is installed properly Whenever use power supply or reserve battery you need press power key to turn on the terminal In normal state When the power cut down the reserve battery will switch into discharge state to power on the terminal In power off state when the power cut down the reserve battery will not switch into discharge state to power on If you want to power on the terminal you need press power key to turn on the terminal 26 www BioTrackSoftware com BioFace Series Installation Guide SS Na key la gt MA Technical parameter Charge time Less than 4 H Discharge More then 5 5 H hs Fed IA Working OC 50C Relative 10 90 humidity Storing Please store the battery when the discharge environment capacity is full and the environment is 20 C 5C Cycle age Cycle times of charge and discharge2300 times Notice There is a danger of battery exploding leak fever fire break if you don t read the notice carefully A Do Not use it over 50 C A Do Not inverse polarity connection A Do Not put the battery into water or let it to get wet A Do Not use and store battery near heat generating machine such as fire or heater 27 www BioTrackSoftware com BioFace Series Installation Guide A Do Not throw batteries into fire or hot batt
15. y slot ee ee Y A Power TCP IP USB connection terminal Loudspeaker SS aa a a www BioTrackSoftware com BioFace Series Installation Guide 2 The illustration of system construction 2 1 The illustration of system construction x i ii I in asus R5232 485 Switch www BioTrackSoftware com BioFace Series Installation Guide 2 2 The sketch map of communication 1 Fingerprint machine directly connects with PC through RS232 or TCP IP TCP IP or RS232 io 2 Fingerprint machine connects with PC U RS485 neiwore a SS Fes 485A gem i 185B 9 ABSA 485B gt RS485 EN ES gt TCP IP www BioTrackSoftware com BioFace Series Installation Guide 3 Installation 3 1 Installation Steps 1 Affix the paper template to the wall and drill holes within the three marked circles on the paper template We recommend affixing the template about four 4 feet 1 2m above the ground assuming the average height of your users is 5 6 feet tall 1 5m 1 85m 1 2M 2 Now affix the mounting plate on the wall by drilling three 3 screws into the three 3 circles marked on the paper template w 3 After installing the back cover ensure it will be stable solid and non loosening 8 www BioTrackSoftware com BioFace Series Installation Guide 3 2 Conect with other devices Caution Do not to connect peripheral equipme
Download Pdf Manuals
Related Search