Home

AquaMetrix 2300 - Lesman Instrument Company

1. 1 3 Front Panel Display The 2300 front panel display shows a series of RUN screens and MENU screens It is meant to be the secondary user interface and has only select capabilities such as viewing status calibrating probes setting relay set that have already been defined by the primary network interface There are eight navigation buttons below the screen including four arrows The functions of the others are e RUN brings up the quad screen from anywhere e MENU brings up the front panel menu e BACK returns the user to the previous screen and e ENTER selects the highlighted choice The Run screens include a summary screen showing the status and values of 4 probes at one time If more than 4 probes are enabled in the controller the Down and Up arrows may be used to see more than the first 4 probes Detailed status screens are shown using the Right arrow button which brings up the first probe status with monitor and relay settings The Down and Up arrows cycle through screens of individual probes Pressing the Left arrow button brings back the summary Run screen When a probe activates an alarm the front panel display automatically switches to a flashing detailed status screen To restore the screen to the full display simply click on or for the real controller press the Run button Each quadrant in the Run screen shows a probe label current value with units trend arrows for the reading and a status light for the controller o
2. Automatic Axis Maximum 14 Bl Automatic Save Figure 3 Config screen for setting up axes of graph shown in the Probe Status screen N116 133 AquaMetrix 2300 Installation and Operation Manual Page 9 1 7 The Web Menu Clicking on one of the five top buttons brings up new screens with submenus The overall menu structure and description for ADMIN access via the network is shown below in Table 2 Table 2 Menu structure of the web interface Displays the current values of the sensors along with recent history and monitor status Config Button Allows reformatting of the history alarm acknowledgement Trend Chart Allows viewing of longer histories Remote Display Displays a simulated image of the current front panel of the 2300 with active buttons Clicking on one of the 8 navigation buttons changes the screens and moves the cursor just as if these buttons were being pushed on the actual unit These actions update the unit accordingly which in turn updates the simulated display Try to remember to leave the Remote Display in RUN mode Brings up the list of daily data logs in memory allowing data to be emailed downloaded or deleted Also does setting of the period for logging Alarm Logs Brings up the list of alarm logs in memory can be saved or deleted System Logs Brings up the list of system logs in memory including web server errors javascript errors and system access These can be viewed Data Lo
3. seessessseeseeee eene eene nnne rne nenas 13 93 PROMS COC AUI OTE etU ossi ea mUSel in parca sancti tuit reli meram esci um nu eDUc PN TEL Mes ices 14 34 The Probe Coniigu ration WIZOFOiscsseveid i vraie euim SE E utes pp IER pL Idee 15 mo wosPeint Scaling Or alba olia da necis v eI VIN EPE Ead a PN elm ed ri E 17 Sn ME escis Wen Pm 18 BF SOCAN Fae COU E T m um 20 3 Be KFO CONE Rm 20 The K Factor option allows for a constant factor to be used to scale a frequency input into units of flow ie volume per unit time The K Factor is provided by the flow meter manufacturer in units of pulses per volume where volume is typically gallons or liters In order to display and record the proper units for the flow the user must twice enter the volume units and the time units The first time is on the same wizard page as the K Factor where the choices are limited to gallons and liters for the volume and seconds minutes hours and days for the time These entries are used by the 2300 to calculate the proper readings The second time is on the next wizard page for the units to display If the desired units are not on the pull down menu choose Enter new units and type in what you want to see Try to keep the total number of characters tO less Nan O erine EE bu MES PINE 20 4 Configuring Virtual Probes sssssssssssusennnunennnunnunnunnunnnnnunnunnunnunnnnnnnnnnnnnnnnnnnnnnnnnnnnn nannan 20 4 1 Configuring a Totalizer Sensor sssessssssssesser
4. the trip point must be greater than the reset trip point and for a low alarm or control the trip point must be lower than the reset trip point An error message will appear if these conditions are not met The next input on this screen allows one to send an Email notification when the probe reading trips a condition There are two other inputs on this page relating specifically to alarms One is External ACK Control which offers a choice of alarm acknowledgements There are four contact closure sensors on the rear of the 2300 which allow for and external switch to be used to acknowledge an alarm an event which is logged along with the original alarm and any of the free digital inputs can be used as well see Figure 17 Sending one pulse to the selected digital input will acknowledge the alarm Multiple alarms may be acknowledged with one of the digital or contact inputs For example a momentary push button switch may be wired to Contact Input 1 and be selected to acknowledge all or some of the defined alarms when setting up each alarm as shown in Figure 18 Meter 4 Configuration Wizard Type Precision Flow Digital Input 1 6 First Monitor Configuration Monitor Name Flow too high Monitor Type High Alarm External ACK Control Hold Alarm until ACK E None Relay Number 25m pem 2 Relay 4 Select Relay Contact Input 2 Alan Contact Input 3 90 Contact Input 4 Alarm OFF 85 Send Email o No Email 9 Send at Alarm ON Point Add M
5. All rights reserved Water Analytics Inc 100 School St Andover MA 0810 Information info wateranalytics net Support issues can be emailed to support wateranalytics net Warning The AC power input presents an electrical hazard N116 133 AquaMetrix 2300 Installation and Operation Manual Page 2 AQUA Metrix WW water Anaiyics 2300 Multi Parameter Controller Table of Contents AquaMetrix 2300 Controller Installation amp Operation Manual 1 To OV 10 aetna ance 5 CE Modu CLOT RTT mE 5 T2 SCCM CACO MORTE T 5 L3 From Panel DISA sinesmenean nasa eeecsesaae he pecaaconeconeasonecseiaudencaaoraaneeoeautenieowiess 6 L4 Front zia BI Tm 7 1 5 Ethernet Connection to a network switch or router ceccesccceseceseeeeeeeeneceeeeeeeeeneeaseeseees 8 13 Prope Status SC SCI tepido R DIM ID EIS obe NNN 8 UN E URSI E aE E A E E A ANEA 10 2 Installation and Housekeeping sss ssussussunnunnunnunnunnunnunnunnunnnnnunnnnnnnnnnnnnnnnnnnnnnnnnnnnn nnne 11 2 PNA CA E a T E E ones E ER 12 Dele T S a S 12 2s EMISE e E R a oe eee reer 12 241 Cone Daa EOPBIDE Ss d aN N EEE OEE E TS 12 3 Connecting and Configuring Probes eere nnns 13 alc CongbuknmeABaSloB Sel OL S easain E oesene lt lam dte ppu E Dnm iM PN a cA 13 3 2 Connecting Pulse Rate Output Sensors
6. Relay Output card esses nnns 43 7 channel Digital Input card cccccccssecsecceecceseccseccencceseeseeeceneceneesseceeneeeseeeeneeeneesseesenes 43 4 channel Analog Output Card cscccssseessosccuscoesscessuscouscoesseessusceusteessescousenussesssesceusess 43 Rebuilding a Corrupted Internal SD Card 44 Panel Mounting DIMENSIONS e eeereeeeee nennen nennen nnnm nnnm nnns annua nnn nnns 45 N116 133 AquaMetrix 2300 Installation and Operation Manual Page 4 1 Overview 1 1 Introduction The AquaMetrix 2300 Controller is a multi input controller that is web enabled such that it can be setup in minutes from any web browser It contains a number of Set up Wizards to aid the user in entering information much of which is not reproduced in this manual The Wizards and most other screens in the 2300 Controller are organized by a dialogue followed by a summary page with Submit and Cancel at the bottom The user may familiarize himself herself with the 2300 by going through most menu functions and just hitting Cancel and not Submit The standard configuration inputs up four 4 20mA analog sensors and three digital frequency inputs for flow monitoring Outputs include four relays and unlimited email text notifications The 2300 Controller provides remote viewing capability and configuring with password from any conne
7. aguametrix2300 juno com If you want to set up sending from your own email account talk to your IT Department or follow the directions below Note that the 2300 internal web server does not support SSL security protocol so you may have to establish a third party email provider such as juno com to generate the emails To change the email server select Setup Network Setup Email Setup SMTP Connection Setup The two required configuration values are the SMTP server address and the SMTP port The SMTP server address can be entered as a DNS name e g SMTP mycompany com or an IP address 192 168 2 200 The SMTP port is a number that is assigned by your IT department and is normally 25 You should get both of these values from your IT department The Global From Address will be used in all email messages as the sending email address e g myemail mycompany com You also need to enter email addresses optionally enter form emails to use later and send a test email 2 4 Configure Data Logging If you will be using the data logging feature of the 2300 check that the default settings for the data file are what you want Default values are 1 Data log files will be kept for 15 days 2 Data will be logged every 5 seconds N116 133 AquaMetrix 2300 Installation and Operation Manual Page 12 3 File delivery is by manual download from browser and 4 Data is stored for configured probes only To change these settings go to Setup gt D
8. as liter min or cc sec while the volume defined in the totalizer can be set to gallons or kiloliters The current value of the Totalizer is displayed in the units that the user chooses Three types of monitor functions are supported High Alarm High Control and Periodic Counter Alarm Email Text notifications and relay closures are accessed the same as for the N116 133 AquaMetrix 2300 Installation and Operation Manual Page 20 Monitors for the other probes The Period Counter Alarm will go off each time a multiple of the set total is reached if the Totalizer is set up with a K Factor or linear scaling Use of the non linear scaling feature allows for more complex functions of this Periodic Counter Alarm 4 2 Configuring Differential Sensors The Differential Sensor is an option for the probe type in the Probe Configuration Wizard It combines two pre existing analog or digital probes and performs a subtraction operation between them displaying the resulting differential value as a separate virtual probe Thus there are 3 readings on the controller for two actual probe inputs A typical application would be to measure the difference of flow before and after a valve or a difference in temperature The differential sensor may be scaled after the subtraction and units assigned to the resulting value just like another probe Similarly controls and alarms may also be assigned to the differential value Be aware that the difference value is alre
9. download from browser Output only Configured Probes C Output Changes Only CZ Figure 20 Data Logging Configuration Wizard page 2 6 2 Alarm Logs Alarm logs track every time an Alarm is triggered Alarm logs are stored as one log file per day The CSV data file is named with the current date in the format of A 131101 csv which indicates the year month and day for the log November 11 2013 for this example Alarm logs are displayed in the Alarm Log listing on the 2300 N116 133 AquaMetrix 2300 Installation and Operation Manual Page 28 7 User Maintenance and Passwords 7 1 Web Passwords The 2300 Controller is password protected for web access and PIN protected by the front panel Users are added changed or deleted from the Setup User Maintenance selection menu Each user name must be unique in the system and can contain letters or numbers The password may only contain letters or numbers and a PIN may be added at this point for front panel access User access to the 2300 is logged allowing traceability of changes made to the controller by username and by time There are three different access levels provided by the AquaMetrix 2300 1 Administrator Can view all reports add change or delete Sensors change system settings and add or delete Users 2 Editor Can view all reports change Set Points for Sensor Relays Acknowledge Alarms and Zero Summarizer Counters 3 User Can view all reports and logs but cann
10. fish tank is above the alarm set point Add Monitor Cancel Summar Back Figure 19 Probe Configuration Window page 5A showing Email notification setup Most wireless phone carriers have Email addresses which allow the content of Emails to be sent to a phone as a text message Emails sent by the 2300 may therefore be sent to most cell phones for instant action eliminating the delay of checking one s Email To use this feature you must know the cell phone carrier of the recipient and add to it an Email postfix specific to the wireless carrier A list of postfixes for some of the most common US and Canadian carriers is in Table 3 For example sending an email to a Verizon cell number 9785551111 vtext com will end up as a text message on the Verizon cell phone with US number 978 555 1111 If your provider is not on this list search the web or ask you cell phone provider for the text email for your service N116 133 AquaMetrix 2300 Installation and Operation Manual Page 26 Table 3 Emaildomain names for common hosts Verizon Wireless Rogers Wireless Telus Mobility 6 Logs and Data Logging There are three types of logs that the AquaMetrix 2300 Controller generates listed below 1 Data Logs track scaled values for all configured Sensors and output Relays Log entries can be saved up to once every second Logs can also be configured to conserve space by only saving an entry if the value has changed from the previous
11. period 2 Alarm Logs track each time an alarm is triggered for a probe and when acknowledged 3 System Logs There are up to seven system logs described below o System Access Logs store every configuration that is changed for the AquaMetrix 2300 Controller Entries are added for system starts and shutdowns Sensor enabled or disabled and users added or deleted In addition each time a user logs into the browser interface that event is logged as well any user initiated changes The log file size is limited to a maximum of 0 5 megabyte and when that size is reached it is renamed to a backup name and a new file is created o Email Message Logs store the time subject TO address and message text for each email sent by the system along with the monitor that triggered it This is useful to track Alarm emails to ensure they were sent The maximum number of alarm logs stored is fifteen days of data To download an alarm log just click on the name of the desired log The current Email message file is named EMAILMSG TXT and is formatted as a text file The log file size is limited to 1 megabyte and when that size is reached it is renamed to a backup name and a new file is created named EMAILMSGO TXT Only one backup file is saved o Web Server Error Logs store any request that generated an error from the internal web server o Jscript Error Logs store any javascript errors o Web Server Access Logs store each request sent from a webbrowser to t
12. AQUA Metrix oy Wa Water Analytics AquaMetrix 2300 Controller Installation amp Operation Manual V1 3 Water Analytics 2014 All rights reserved AquaMetrix 2300 Tank pH Tank ORP 7 35 51386 gt pH e mVe o Tank D O Tank Level 3 927 88 cm fe j O O D D i i E Last revised February 11 2014 For Your Safety Please read this entire manual before unpacking setting up or operating this equipment Pay attention to all danger and caution statements Failure to do so could result in serious injury to the operator or damage to the equipment Make sure that the protection provided by this equipment is not impaired do not use or install this equipment in any manner other than that specified in this manual If this equipment is used in a manner not specified by the manufacturer the protection provided by the equipment may be impaired Statement of Limited Warranty WATER ANALYTICS warrants that this product is free from defects in workmanship and material for a period of 24 months for electronics from the date of delivery from the factory or authorized distributor under normal use WATER ANALYTICS s liability under this warranty shall be limited to replacement or repair of any defective equipment or part which having been returned to WATER ANALYTICS transportation charges prepaid has been inspected and determined by WATER ANALYTICS to be defective Copyright 2014 Water Analytics Inc
13. Figure 11 Probe Configuration Wizard page 3 Note that any changes to the scaling calibration factors submitted at the end of this Wizard will reset the date of calibration for that probe Editing other portions of the Wizard will not update the calibration date If you are setting up the probe for the first time we recommend that you first test the probe operation click on Summary review your inputs and click on Submit This will bring up the Probe Configuration page click on Probe Status at the top of the page and view the probe reading Run it through tests if desired to ensure it is working reading as expected If all is well go on to configure an alarm relay or notification 3 6 Non Linear Scaling The example provided below in Figure 13 shows the relationship between a temperature sensor that outputs a logarithmic scale compared with a simple Fahrenheit temperature scale Each line that connects the two scales shows the relationship between them and how it changes over the temperature range For each point on the Analog input sensor scale a corresponding value must be entered into the output side The graph in Figure 13 shows the input Analog scale on the X axis and the output Temperature scale on the Y axis The data entry can be achieved by simply clicking on each point on the graph to draw the curve As the mouse cursor hovers over a data point both the Analog and Output scaled values are displayed Each point in the graph is d
14. PS BV OO NOS OO NOS ON NOS HO SYNC A Figure 30 6 Relay Output Card connections 13 3 7 channel Digital Input card The 7 channel Digital Input card provides seven additional digital inputs with the following connections DIDDGEIDOD DODDOD am S de X e x0 Ko aS e e FN X S MR NC ANO UND MC UNS AO S LG GAS GS ue AR S y Qv Qv Qv ym Qv S S Qv SV Qa Qv Figure 31 Input Card connections 13 4 4 channel Analog Output card This card provides for 4 channels of 4 20 mA output loops which may be programmed via the Monitor function in the Probe Configuration Wizard More than one output may be set for an input and the outputs may be used for the virtual channels as well If the card is in place the drop down menu of the Monitor Type will show Analog Output on the bottom of the list If chosen the output may be mirrored to an analog input or scaled to the value of any probe real or virtual For further information refer to the instructions accompanying the card N116 133 AquaMetrix 2300 Installation and Operation Manual Page 43 ANOuti ANOut2 ANOut3 ANOut4 24v GND NE S v T MS i Lu EE 330 MI NI Sa Si 2 Si Figure 32 Analog output card connector 14 Rebuilding a Corrupted Internal SD Card We recommend that you perform a SD card backup after the configuration has been setup and verified The backup can be done to the same SD card that contains the version Update information There are two things that mu
15. RE TT 3 65 C PANEL CUTOUT J iy PANEL MOUNTING WALL MOUNTING USING OPTIONAL ENCLOSURE N116 133 AquaMetrix 2300 Installation and Operation Manual Page 45
16. The contacts D1 and D2 are high precision optically isolated frequency counters while D3 is not isolated D3 uses a one second count of the pulse rates to determine frequency N116 133 AquaMetrix 2300 Installation and Operation Manual Page 13 Wiring of a pulse rate sensor is shown below in Figure 7 The three wires from a typical unpowered probe are and signal Power Supply GND 24V 2300 Controller AquaMetrix 2300 i EK Digital pulse inputs Signal or o1 Jo2 02 Jos 03 Pulse Input Connector Block Paddle Wheel Sensor Figure 7 Configuring a flow sensor paddle wheel or magmeter to one of the pulse input connections 3 3 Probe Configuration Setup The Probe Configuration menu screen is shown in Figure 8 This screen appears in the web menu at Setup Probe Configuration This screen is used to enable or disable individual probes to set up the order that the probes are displayed on both the front panel and web to delete old probes and to add or substitute new probes to the controller Eight slots are listed which is the order that the 2300 s software keeps track of the probes Each slot may be configured as analog digital or virtual probes Slot refers to the position on the front panel and web Probe Status displays N116 133 AquaMetrix 2300 Installation and Operation Manual Page 14 This page is where you configure the parameters for monitoring and controlling each Probe Probes are n
17. ady scaled from the input current values so that further scaling is liable to provide non meaningful values We recommend using either No Scaling or Scale Factor scaling The difference value may be either positive or negative The differential sensor may be edited but the original two inputs it is based on are fixed in its definition To change one or both inputs delete the differential sensor in the main Probe Configuration menu and define a new one 4 3 Configuring a Flow Sensor for Batch Control The Dispenser Probe option allows the 2300 Controller to function as one to four complete batch controllers There are two types of Dispenser Probes selectable in the 2300 Controller Both are used to monitor a flow in order to dispense a fixed volume of fluid The vast majority of users will select the Manual Start Dispenser which initiates the flow via a relay based on input from a contact switch closure The Flow Dispenser initiates the flow based on a monitored value of one of the analog inputs to the 2300 Controller This allows triggering of the flow based on a pH temperature conductivity or other parameter being exceeded Both Dispensers have a user set time delay after the relay is shut off before allowing a new trigger event After selecting the Manual Start Dispenser as Probe Type in the New Probe Wizard a Start Digital Input window allows the user to select any of the available three Digital Inputs four Contact Inputs or by Keyboar
18. art phones via email addresses as per Section 5 2 10 6 Diagnosing Email Problems The first step in diagnosing email problems is to perform the Test Email operation as outlined in the previous section This ensures that the system can properly connect to the Email server used to send emails It is also useful to have a way to send an email at a known time to a known recipient The Email Setup page provides a mechanism to send a test email When you select this choice enter an existing email address from the list or enter a new one Pressing Send Test Email will send a pre formatted email with the subject AquaMetrix 2300 Test Message to the email addresses specified One additional resource is provided by the system the ability to look at the history of all Emails sent A separate log file is maintained that lists each email that was sent including the time recipient list subject and message text This Email log file is described in Section 6 11 Configuring the System 11 1 System Name and Time Under Setup is the System Configuration menu with 5 submenus that cover a range of system settings The first submenu is Name amp Time Configuration This menu allows the user to change the name of the system which will appear on the front panel in the log files and on Email notifications sent from the system Time and date settings are set here for systems that are not connected to the Internet otherwise the unit obtains the time and da
19. ata Logging Configuration and follow the Wizard 3 Connecting and Configuring Probes 3 1 Configuring Analog Sensors In its standard configuration the 2300 has four 4 20 mA analog inputs The rear side block connectors are shown in Figure 5 above Wiring of a sensor depends on whether it is loop powered or externally powered variations are shown in Figure 6 1 If the probe is to be loop powered then its black negative wire connects to the chosen AN IN x where x is 1 2 3 or 4 terminal and the red positive wire connects to one of the 24V terminal 2 Ifthe probe is externally powered such as from a transmitter then its red positive wire connects to the externally to the chosen AN IN x terminal and the black negative wire connects to the ground GND terminal 3 Ifthe probe has three wires it needs an external power supply refer to the probe directions for hookup AN AN AN 24v 24v AN AN 24v 24v AN AN AN AN GND 24v 24v QM MB M int in2 n3 ins Rz GND Two wire Probe Two wire Transmitter Three wire supply Probe Figure 6 Possible analog probe wiring diagrams There are other possible three wire probe setups so please refer to your specific probe s instructions for proper hook up 3 2 Connecting Pulse Rate Output Sensors The 2300 has inputs for 3 pulse rate sensors These are typically flow sensors that output a sinusoidal or square wave e g paddlewheel and magnetic flow meters
20. ation and Operation Manual Page 33 port forwarding also called port mapping We recommend talking to your IT department or IT consultant to set this up Alternatively we have outlined some of the steps below Every device on a LAN has an IP address that is only meaningful to users on the LAN The router that creates the LAN has an IP address that is unique in the world If you don t know what that external IP is open a browser and enter the URL www WhatlsMyIP com The website will immediately return your external IP Its address will be very different from the LAN s IP addresses and look something like 24 148 220 199 With port forwarding an item that has its own local IP address is assigned a port number on the external IP The port forwarding number is just about any number that you make up However we recommend avoiding any number between 0 and 100 and preferably a 5 digit number Let s say you choose 5000 for the port forwarding number of a 2300 The external IP address of the 2300 then becomes using the above example 24 148 220 199 5000 The next task is to go into the 2300 and assign to it the port number that you just created At the unit s local display enter Menu gt Advanced Menu last menu item gt Network Setup gt Web Server Port Type in the number in our example 5000 and press the DONE key Press the Commit and Restart button and you re done The one task we have not explained is setting up port forwarding on your r
21. be less precise than the precision inputs It uses the digital input number three but may also be defined for digital inputs one and two The second page of the Wizard is shown in Figure 10 Enter a probe name which appears on both the web interface and the controller s front panel The Scaling Calibration Type is a pull down menu shown with 5 options No Scaling displays the raw current from the probe Linear scales the input based on 2 points This is common for a 2 point calibration Non Linear scales the input from a fit to up to 32 points Scale factor scales the input with a constant value K Factor is a flow constant in units of pulses volume This inversely scales the pulses or frequency of an input and converts it to volume per unit time MT dix c I en N116 133 AquaMetrix 2300 Installation and Operation Manual Page 16 Meter 5 Configuration Wizard Type Precision Flow Digital Input 1 2 Probe Information Enter Probe Name Show Detailed Probe on LCD 14 No Scaling Linear 2 points Non Linear up to 32 points Scale Factor l L K Factor whose ratio does not change over the entire range of data Non linear scaling is for measurements whose ratio can change as the input value increases such as on a logarithmic or exponential scale Up to 32 points can be entered to describe complex formulas Cancel Summary Figure 10 Probe Configuration Wizard page 2 Whether or not the scaling operation is a calibrati
22. cccccseccseccsecceeccenecesecseneeeeeteeseeeeeeeees 33 Configuring the 2300 for a NetWO0rK s ssusssseunnnnnnunnnnnnunnnnnnunnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnne 33 Baen AE E a A E E 33 Viewing the 2300 on a Wide Area Ne twork ccccccsssccsseccseceeeeceeceeeeeseeeeneeeeeeseeeaeeaeeeees 33 Dedicated wireless connection via a Smart Phone or Tablet cc ccccceccsecceeceeeceeeeeeeeens 34 Static IP Address Setup and Wired Connection esee 35 iat finu d inr Pec 36 EENE SC IO cae cesses TT T T 36 Web Server and TFTP Server SetulDS escuesenceseeuses set vi ina gokvEx va Dd bb Ode curd e d cU ebrietas 37 IRR C IND e E T T mem 37 Emal ICV WOU NUN Em 38 Emal TO Addres SOS reiini E E 39 Diagnosing Email Problems scasecossciatendectusendeasesesennyavercaaed Aaauaeimetsastacawnssanadeaeteiuineeanaacdeeecs 39 Conhgurmge Hie Syster isin EAER 39 System Name and TIME TOT 39 Browser Configuration and Logging Out essssssssssesrrssrssrrssrserrsrrsrrreerrersrrsrererrerrsrerrererene 40 EC DCO WA IE ol Tm 40 ER Or Fel GUUS TOT 40 Bd anne 41 Advance lt 9 nee nnn mandarin a DE UI eS ene epee X DU eee EU UE 41 Avalaple 1 0 Card Dad I 1g 0 Pe Mm 42 3 channel Digital Input 4 channel Digital Relay Output card eeeeeeees 42 6 channel Digital
23. croll down to Save Restore Configuration then select Save and Confirm The 2300 will display a message that the save was successful To restore the configuration insert a microSD card with the desired configuration file folder called BACKUP Go to Menu scroll down to Save Restore Configuration then select Restore and Confirm The 2300 will first ask if you want to change the IP address as well After restoring the 2300 will display a message that the save was successful Restore will only work with units with the same firmware build Upgrades to firmware will not change the configuration inside the 2300 so we suggest saving the configuration to a memory card after a firmware upgrade 9 Configuring the 2300 for a Network 9 1 Dynamic IP Setup This is the default set up of the 2300 allowing the network to assign an IP address to the 2300 To connect within a network just type the 2300 s IP address into a browser The IP address of the 2300 is shown in the menu on the View System Info page The IP address is listed on the second line and will look something like192 168 1 5 Type the IP address into a web browser and a dialog box will appear that asks for your username and password 9 2 Viewing the 2300 on a Wide Area Network As with any device on local area network one can view the 2300 outside that LAN from anywhere in the world on a so called Wide Area Network WAN To do so requires the use of N116 133 AquaMetrix 2300 Install
24. cted web browser It also provides data logging with downloading or emailing of log files in CSV format There is also one available slot for an optional card which can expand digital inputs or relays outputs or add analog outputs 1 2 Specifications Table 1 Specifications Inputs Analog Four 4 20 mA powered or unpowered current loops Pule Rate Two optically isolated inputs suitable for flow sensors up to 24 VDC or 120 VAC Counter One accumulator for tracking equipment on time Contacts Four contact sensing inputs for alarm acknowledgement or remote resets Outputs Relays Four 120V 240 V 10A 5A expandable to eight Alerts Emails and or texts for alarms relay actions errors or reminders Web Remote viewing with a browser on a computer tablet or smart phone Remote programming from any of these Data logging Logging of CSV files directly to micro SD card Digital Outputs Modbus TCP over Ethernet connection Analog Outputs Optional Four non isolated 4 20 mA outputs proportional to any reading Control Web or LAN Viewing with a browser on a computer tablet or smart phone Setup and control from any of these Multi user password protected Front Panel Status Probe enable disable calibrate System Configuration Ratings N116 133 AquaMetrix 2300 Installation and Operation Manual Page 5 Front cover 6 5 wide x 5 5 tall rear enclosure 3 5 wide x 3 5 tall x 4 5 deep One expansion card slot is available
25. d Input Only In the same window the flow input that controls the volume dispensed is also selected from one of the analog probes or digital flow probes This flow input may or may not be selected from a flow channel previously set up The Wizard starts from here with Instructions on page one Information on page two Scaling on page three Probe Description on page four and Dispenser Control Configuration on page five Dispenser Control determines the value of the target volume or total the relay to activate and the delay time before the function is active again The Flow Dispenser is set up in similar fashion the main difference being that the trigger is a preconfigured value from one of the analog probes Only high values are available but all of the high alarm and high control functions that are then currently set up in the 2300 Controller are available to the user to choose from the pull down menu on the Probe Select page N116 133 AquaMetrix 2300 Installation and Operation Manual Page 21 5 Configuring Alarms Relays and Notifications Each probe can be monitored to provide multiple alarms relay activations and Email notifications The 2300 is set up to allow full flexibility of assigning any or all of these outputs to any or all of the probes including the virtual probes You are only limited by the number of hardwired relays on your controller four of which are standard but more may be added using an optional card There are un
26. dress will be used in all email messages as the sending email address e g myemail mycompany com You also need to enter email addresses optionally enter form emails to use later and send a test email Some SMTP servers require authentication and if it does you must check the appropriate checkbox on this form and also fill in the user name and password information on the next page N116 133 AquaMetrix 2300 Installation and Operation Manual Page 37 SMTP Connection Wizard 2 Basic Information SMTP Server Address SMTP Server Port 0 Global FROM Address Does your SMTP Server require authentication Ej Yes O No Back Figure 27 Email configuration The second submenu is Send Test Email which generates both an email and diagnostic message to indicate all is working or what is not Test the SMTP connection every time there are changes made to the SMTP server settings The third submenu is Email Message Setup This screen allows the user to compose emails to use in the Probe Configuration menu streamlining both the probe setup and avoiding entering duplicate data The Email message body may contain variables to provide the email addressee with specific information on why he or she is receiving this email and may also include action items for the addressee to perform 10 4 Email Keyword List The following table represents a list of keywords that can be inserted in an Email message text The Name field is what is dis
27. e into the Ethernet connector shown in Figure 2 and connect the other end to a network switch or router Type the address into the address window of your browser hit enter and a login window should appear The default username is admin and the default password for admin is aquametrix Note that there are two other levels of password protection that don t access everything that the admin level does Users may be added via Setup User Maintenance to uniquely identify login identities that access the controller See Section 7 1 6 Probe Status Screen When first logged into the 2300 Controller from the web the Probe Status screen appears showing all of the probe readings An example of this screen showing four probes is shown in Figure 2 The order of probes shown is user determined via the Setup menu Each has a label a reading and a graph of recent values Last Calibration date and a graphic of the alarm and relay states for each probe The red Alarm triggered and green not triggered bars to the right of each graph depict the alarm A state and relay R state with set point and reset values If using the optional analog output card this value will also be shown under an O label to the right of the trend chart A yellow bar indicates that an action is taken but non alarm such as a relay activated or analog output generated Clicking on a Config button brings up a new window that displays the probe description and allo
28. ed current for a particular solution For pH as shown you can place the probe in a known reference solution the reference solution pH for the previous calibration is remembered and doesn t need to be entered again if the same Wait until the reading at Use measured mA is stable and select it and hit Enter Move down to Confirm Calibration and hit Enter to save this data point To enter numbers manually a keypad entry screen is used Repeat if desired for the second point and scroll down to Done Enter mA manually Use measured mA 11 450 Enter solution value Confirm Calibration fe t O O o D S En Figure 23 Point 1 calibration screen To change the K Factor of a flow meter go to the page with choice of probes and select one of the flow probes A screen for changing the K factor will appear and selecting it will bring up a numeric keypad entry screen These screens are show in Figure 24 Note that the previously stored value for the K Factor is shown in parentheses in the entry pad The Back button on the keypad will erase the last digit entered and don t forget that the navigation keys move you around the keypad Use Done to save the entry and Done again to save the calibration N116 133 AquaMetrix 2300 Installation and Operation Manual Page 31 82 4 Multi Parameter Controller Multi Parameter Controller Figure 24 Calibration screens for probes with K Factor scaling 8 2 Fron
29. ernet Every operating system is different There are many web resources that will guide you on configuring the Ethernet connection on your operating system 2 Select Manual configuration of IPv4 vs automatic 3 Youarefree to choose the settings for IP address Subnet Mask and Default Gateway The default static IP address of the 2300 is 192 168 7 7 so we will use these numbers in this example On your computer use the following numbers a IP Address 192 168 7 1 N116 133 AquaMetrix 2300 Installation and Operation Manual Page 35 b Default Gateway 192 168 7 7 c Subnet Mask 255 255 255 0 Note that the IP address and Default Gateway are the same That is because the computer is the gateway On the 2300 Controller 1 On the front panel go to Menu gt Advanced gt Network Setup 2 Select Network Type and then Fixed vs DHCP The Fixed Network Setup screen will appear 3 Select IP Address and use the resulting keyboard and navigation keys to enter a new IP Address 4 The settings for the Subnet Mask and Default Gateway will be the same as for the computer However the IP Address will be different For the above example a working set of values might be a IP Address 192 168 7 7 b Subnet Mask 255 255 255 0 c Default Gateway 192 168 7 1 5 When complete press the Commit and Restart button Open a browser on the computer and type in the IP Address given to the 2300 Controller 192 168 7 7 in the example above The log
30. ess software version and system status information Disable Calibrate Probe Manually disable enable or calibrate defined probes Backup Restore Save or restore the unit configuration and setup to a removable SD card Reboot System Powers down and restarts controller Prepare for Power Down After a confirmation dialog is confirmed all probes are disabled all logs are closed and the system is put in a state where it is safe to remove power from the controller Confirm or cancel choices N116 133 AquaMetrix 2300 Installation and Operation Manual Page 7 These functions are geared to ensuring that the unit may be connected to a computer or the web to allow setup and configuring When not connected to a computer or web the unit is still operating and all non web based features are still fully functional 1 5 Ethernet Connection to a network switch or router Connecting the 2300 to an existing network with the Ethernet cable allows the 2300 to be automatically assigned an IP address You only need to set the Ethernet connection on your computer or smart device to configure via DHCP The IP address is shown on the front panel during power up or can be seen via the Main Menu under View System Info hit Menu then Enter from the front panel The IP address may look like 192 168 1 7 save this address to access the 2300 from the network Refer to Section 9 4 to use a static IP used for direct connection to a computer Connect a CAT 5 cabl
31. gs saved or deleted Probe Configuration Set up sensors alarms relays and notifications See Sections 4 and 5 for details System System doc file Documentation Advanced Miscellaneous functions N116 133 AquaMetrix 2300 Installation and Operation Manual Page 10 2 Installation and Housekeeping Mount the 2300 Controller through the front panel with the gasket on the outside of the mounting panel Hook the sliding mounting blocks on each side of the back of the 2300 enclosure and tighten the setscrews against the mounting panel with a torque of 4 in Ibs as shown in Figure 4 Connect an AC power cord to the power connector labeled in Figure 5 Figure 4 Mounting hardware attached to panel with 4 in Ib of torque o no no no no no no no Relay Outputs ib 2a 2b 3a 3b 4a 4b Power 120 220 VAC N AN AN AN AN cun 24v ind in2 in3 AAA E Contact Inputs Figure 5 2300 back panel All connections are made via connectors on the back N116 133 AquaMetrix 2300 Installation and Operation Manual Optional Card Slot Pulse Rate Input Analog Probe inputs Ethernet Connection Fault LED System Operating LED Power On LED Page 11 Apply power on to the 2300 Controller The front panel will first display a splash screen with the AquaMetrix logo If the 2300 Controller is operating properly the LED s on the back panel indicate proper operation The Power ON should be lit the Fault should a
32. he AquaMetrix 2300 Controller It is not enabled by default but can be activated from the web server Setup Network Web Server setup page It is only necessary when trying to diagnose web access issues These logs are available for downloading under the Logs button on the main web menu N116 133 AquaMetrix 2300 Installation and Operation Manual Page 27 6 1 Data Logging Configuration Wizard Data logging will send all sensor information and all configured digital input data to a central CSV based log file The log files are organized using the Data Logging Configuration Wizard located at Setup Data Logging Configuration Page 1 of the Wizard determines the number of days for which the 2300 keeps log file Page 2 shown in Figure 20 determines the Logging Frequency in seconds and the Delivery Method either via Manual Download from your browser or Email Delivery Email delivery can be set to periodically email the data log file every day at midnight or more often Page 3 is the summary page allowing the user to review the inputs prior to submittal Data Logging Configuration Wizard 2 CSV Log Generation Configuration This page controls how CSV log files are generated Email delivery will generate a CSV file and attach it to an email sent to the specified email address Control of when the email is generated can be set from every 15 minutes to every day at midnight CSV Logging Frequency seconds 10 Delivery Method Manual
33. in screen should appear see Section 1 5 for the logging in 10 Network Setup Setup Network Setup brings up four submenus for configuring of the network e Ethernet Setup e Web Server Setup e TFTP Server Setup e Email Setup 10 1 Ethernet Setup The first submenu is Ethernet Setup allowing you to change from DHCP to Static IP and back again Since you are communicating to the 2300 across a well defined network connection changing this and restarting will sever your connection However if you are configuring a system to be used elsewhere you may set up the Ethernet for this new location using Save to allow the new settings to take place upon restart at the new location This function is also available in the front panel menu system By unchecking the use DHCP box three additional boxes will appear for entering the static IP address the subnet mask and the gateway address After entering you must Save or Save and Restart in order for the changes to be saved You may also specify one or more DNS server IP addresses separated by commas e g 1 2 3 4 5 6 7 8 N116 133 AquaMetrix 2300 Installation and Operation Manual Page 36 10 2 Web Server and TFTP Server Setups The second submenu is the Web Server Setup which allows the setting of the internal web server port as well as enabling or disabling the access log and error log If the web server port is changed the AquaMetrix 2300 must be restarted for this change to ta
34. isplayed with a hollow circle and can be edited with a right click mouse action This menu allows Edit mAmp Value or Edit Output Value The Get Current Value selection loads the current raw value from the sensor and updates the selected data point This is useful if the scaling curve N116 133 AquaMetrix 2300 Installation and Operation Manual Page 18 isn t known beforehand A data point can also be deleted with the appropriate selection Clear All will clear the entire graph so the mapping process can start over A separate Data Point List is also provided which lists each data point with one point per row The data points can be directly changed in the Data Point List or by clicking on a plot point and moving it manually Input Analog Values Output Scaled Values mAmps degrees Fahrenheit 114 9 F 69 4 F 4 5mA 40mA E Figure 12 Non linear temperature scaling example Maximum Output Unit Value 255 O O M 250 l i i Mapping Line of Input to Output data points 4 20mA Axis Scale 0 5 0 7 5 10 0 12 5 15 0 17 5 20 0 Current Update TEE o Current Position 14 82 mAmp 50 07 F Position in Input and Data Point List Point millihmps F Output units 1 4 500 15 8 s 2 6 800 21 4 Data Point 3 8 900 28 2 List of 4 11 000 43 2 mapping 5 13 600 69 4 points 6 16 000 114 9 7 17 100 153 5 Cancel E NW Figure 13 Probe Configuration Wizard Non linear sca
35. ke effect The third submenu is the TFTP Server Setup This configuration page allows the setting of the internal TFTP server configuration The TFTP Server should not be enabled under normal operation as it is a potential security risk If the TFTP server is disabled or the port is changed after it is started the 2300 must be restarted to take effect 10 3 Email Setup The fourth submenu is Email Setup It is necessary to setup email addresses SMTP server and stock email messages The 2300 is preconfigured with an SMTP server entry suitable for sending emails and alerts along a network The email sender is aguametrix2300 juno com If you want to set up sending from your own email account talk to your IT department or follow the directions below Note that the 2300 internal web server does not support SSL security protocol so you may have to establish a third party email provider such as juno com to generate the emails To change the email server select Setup Network Setup Email Setup SMTP Connection Setup The SMTP Connection Wizard is shown below in Figure 27 The two required configuration values are the SMTP server address and the SMTP port The SMTP server address can be entered as a DNS name for example SMTP mycompany com or an IP address 192 168 2 200 The SMTP port is a number that is assigned by your IT department we use 587 for juno com You should get both of these values from your IT department The Global From Ad
36. lays and or notifications upon reaching either a high or low level defining a range e Outof Range Alarm Activates alarm and relays and or notifications upon reaching a level inside of a defined range from either direction Choosing one of these Monitor Types leads to modifications of this screen walking the user through the selection of the data needed to set the monitor Figure 15 shows the pull down menu for the Relay Number when High Alarm was selected for the Monitor Type There are 4 relays to select from normally but in this example three have already been configured and only Relay 4 is available Adding an optional expansion board adds another 4 or 8 to this menu If a relay is already being used as here it may not be selected and must first be freed up as a monitor from the specific probe it is linked to There are also choices for Email Only and Display Only that allow the monitor to react to the probe conditions without activating a relay Display Only will set up a green light on the front panel for the monitor and on the web Probe Status screen turning red if an alarm or yellow if a control If a relay is selected clicking on Show Relay will bring up an image of the rear of the 2300 Controller with the corresponding contacts outlined in red This is for information only as the Controller should be powered down when being wired or the wiring should be done to the disconnected connector if the unit is not powered down This featu
37. limited email notifications that may be set up and by using the recipient s cell provider address to deliver text messages to cell phones of almost all wireless carriers 5 1 Types of Monitors To set up these outputs go to Setup Probe Configuration and click on one of the probes listed Click Next until you reach page 6 of the Wizard shown in Figure 14 below Meter 5 Configuration Wizard Type Precision Flow Digital Input 1 6 First Monitor Configuration Monitor Name Flow too high Monitor Type None Fill Control Empty Control Low Control High Control Select Relay Low Alarm In Range Alarm Out of Range Alarm U U Send Email O No Email Send at Trip Point Add Monitor Cancel Summary Figure 14 Probe Configuration Wizard page 6 Monitor Type This example is for Probe 5 i e the probe in the fifth slot of the configuration list and is a Precision Flow meter from digital input 1 top row of page Multiple monitors may be used on each probe and each is configured separately see the Add Monitor at the bottom First type in a name for this monitor then choose Monitor Type the pull down menu is shown here There are four control conditions and four alarm conditions The differences between an alarm and a control are minor both can control relays and send notifications but the alarm function also does the following 1 Switches the panel front display from the RUN screen to a DETAILED screen f
38. ling N116 133 AquaMetrix 2300 Installation and Operation Manual Page 19 3 7 Scale Factor The Scale Factor option just multiplies the scale factor entered by the input This may be used to change units or in the virtual probe configurations to customize the output readings 3 8 K Factor Scaling The K Factor option allows for a constant factor to be used to scale a frequency input into units of flow ie volume per unit time The K Factor is provided by the flow meter manufacturer in units of pulses per volume where volume is typically gallons or liters In order to display and record the proper units for the flow the user must twice enter the volume units and the time units The first time is on the same wizard page as the K Factor where the choices are limited to gallons and liters for the volume and seconds minutes hours and days for the time These entries are used by the 2300 to calculate the proper readings The second time is on the next wizard page for the units to display If the desired units are not on the pull down menu choose Enter new units and type in what you want to see Try to keep the total number of characters to less than 6 The double entry allows complete flexibility of what volume units may be displayed and recorded for flow If the K factor is in pulses gallon but you want to read liters you may scale the K Factor entered and use l min for units Other volume units may be introduced as well so you can count b
39. lso be lit and the System Operating should be blinking The green LED on the Ethernet connector indicates a valid network link The yellow LED will blink when there is network activity Before configuring the probes you have some housekeeping tasks to do which although optional do allow you to use the 2300 s full capabilities like emailing 2 1 Password Change Yes you get requests for password changes all the time but if you want security and don t want all the other purchasers of 2300 s to know your username and password now s the time to change them Select Setup User Maintenance and then add a user Make sure that you click on Admin for the user level and write down the username and password You can also add multiple users at the Admin Editor or User levels in order to track via the logs which users have done what to the 2300 Logout then log back in under your new admin name and delete the default name admin 2 2 Time Setup The time of day sets automatically if the 2300 is connected to the web via an NTP time server To manually set the time select Setup System Configuration gt Name gt Time Configuration Time zone date and time are set here This page also allows you to customize the name of the 2300 identifying the unit by location or function or zodiac sign 2 3 E Mail Setup The 2300 is preconfigured with an SMTP server entry suitable for sending emails and alerts along a network The email sender is
40. me simply by pushing the Run button on the keypad and choosing View System Info The IP address will be on the second line of the System Information screen 5 You may see a screen with the title No IP Address Assigned followed by the message The system has a network cable inserted but cannot get an IP address To do this change type to fixed IP on next page See manual for more Press Enter to continue If you see this screen then simply press Enter You will then see a screen with the title Select Network Type Enter Try DHCP Again 6 On your smart device WIFI connected to the Tenda network open a browser on the and type in this address 192 168 2 100 The username is admin and the password is aquametrix 9 4 Static IP Address Setup and Wired Connection The 2300 can be configured with a static IP address if desired The static IP is required when connected directly to a laptop or any smart device with an RJ45 Ethernet port One typically uses a cross over Ethernet cable for direct connections like this but most newer computers are savvy enough to work with regular Ethernet cables Both the 2300 and the laptop computer need to be configured as follows On the Computer 1 Setting up the Local Area Network for either a Windows or Mac involves configuring the Ethernet connection On a Windows computer this can be found in the Control Panel Network On a Macintosh this can be found in System Preferences Network Eth
41. measurements by the probe in reference solutions Putting the probe into a known solution and hitting the Read mAmp Value automatically inserts that value into the corresponding Low or High mAmp Value field Input the know process value in the case of calibration the value of the calibration standard into the Scaled value fields The 2300 Controller will use these two values to scale all mAmp readings into scaled displayed values with the units chosen on page 4 of this wizard N116 133 AquaMetrix 2300 Installation and Operation Manual Page 17 Meter 1 Configuration Wizard Type Analog Monitor Analog Input 1 Low milliAmp Value 3 Linear Scaling Calibration B 71 Read mAmp Value Scaled value displayed at low input Value 4 00 Use this screen for either scaling or 2 point calibrating the displayed values to the miliamp values received by the AquaMetrix 2300 For scaling enter the low and high milimamp values within the 4 and 20 range corresponding to the low and high Probe readings desired For calibration the probe should be placed in a known solution and the Read miliamp Value button pressed If time to stabilize the reading is needed press the Read miliamp Value button repeatedly at reasonable intervals until the value stabilizes Rinse the probe and place in another known solution and repeat High milliAmp Value 12 23 Read mAmp Value Scaled value displayed at high input Value 7 00 TS a Cancel Summary Back Next
42. n via a Smart Phone or Tablet There are environments in which there is no available local area network or there is a need for a private network isolated from the network For these settings a wireless router is the N116 133 AquaMetrix 2300 Installation and Operation Manual Page 34 solution This will allow the wireless connection of the 2300 to a wifi capable handheld device such as a tablet or smart phone in proximity to the 2300 Aquametrix sells a very compact inexpensive router made by Tenda to connect the 2300 Controller to a wireless device If you purchased a 2300 with a wireless router the router and the 2300 will already be configured and ready to go Follow these simple instructions to connect your smart device to the 2300 through the dedicated local network 1 Connect the router to the 2300 Controller with a standard Ethernet cable Power up the router using the AC adapter included 2 Make sure that the router is set to WISP Wireless Internet Service Provider mode 3 On your computer search for available wireless networks You will see a list of networks one of which will be for the router s network The default name of the network for the Tenda router is Tenda Connect to that network Be aware that you will no longer be connected to the Internet 4 Power up the 2300 After the Aquametrix splash screen shows you will see the IP address that the router assigned to the 2300 If you miss it you can recall it at any ti
43. ollows 0 Probe definition This step defines the probe type and its hardware input Once set and probe configuration submitted this step cannot be accessed or changed without deleting the slot to start over 1 Wizard instructions An overview and the official page 1 of the Configuration Wizard 2 Probeinformation Give the probe a name and calibration method 2 point linear multi point non linear scaling factor and K Factor 3 Probe calibration Screen depends on calibration method 4 Probe details Select existing units for display or make new ones Decide how to format the readings how many digits where does the decimal point go 5 Probe description Type in whatever information you want to accompany this probe such as probe type serial number location notes on behavior etc This info is available to view on the network and on the instrument front panel 6 Probe monitors Monitors are conditions that lead to actions by the 2300 such as alarms alerts relays and proportional outputs See Section 4 7 Summary page Prior to submitting the changes the user may review all the information being saved or cancel without changes N116 133 AquaMetrix 2300 Installation and Operation Manual Page 15 The probe definition page is shown in Figure 9 below There are seven choices of probe types shown the top three being hardware probes the bottom four are functionally based on the outputs of other probes we call them virtual
44. on depends on the signal provided by the sensor If the sensor output comes from a transmitter then it is likely that it has already by calibrated at the transmitter In this case the sensor signal coming into the 2300 simply needs to be scaled to translate current readings to process variable units If the sensor is a direct sensor probe e g a pH sensor then the scaling operation is a true calibration and requires the use of calibration standards e g pH buffers for a pH probe Using these choices is detailed in the following sections corresponding to page 3 of the Wizard After the scaling calibration page the user is brought to page 4 and prompted to select the display digits after the decimal place and the number of significant digits desired Then the Units of Measure is a pull down menu shown that allows the user to select the units displayed for the probe being configured Choose from a list of common units or select Enter New Unit to customize your selection Try to keep the name of the units to 5 characters or less e g US cm although more characters are allowed some screens don t display long names well Page 5 is the description followed by the monitors described in Section 4 3 5 Two Point Scaling or Calibration The third page of the wizard shown in Figure 11 for the linear scaling option provides for scaling for both analog and digital inputs The Linear scaling option allows a two point calibration of the probe using actual
45. onitor Cancel Summary Figure 17 Probe Configuration Wizard page 6 External ACK Control menu Figure 18 Wiring of a switch to Contact Input 1 for acknowledgement of an no no no no no no no no digin1 dig in dig in alarm 1a 1b 2a 2b 3a 3b 4a 4b qoe 4 xS ow a IIT 30731718 37307307337 24v 24v AN AN AN AN cuo MP J Li ES gt a a S B D GND N116 133 AquaMetrix 2300 Installation and Operation Manual Page 25 5 2 Configuring for Email Notification Clicking on Next after selecting Send at Control Trip Point will bring up a new screen page 5 A shown in Figure 19 First select the TO Address from a drop down menu The user may select an email address preset at Setup Network Setup Email Setup or choose to enter a new address The FROM address is preset in the 2300 and may be changed at Setup gt Network Setup gt Email Setup gt SMTP Connection Setup The email Subject may be selected from a drop down menu which populates the message with a pre setup message that may contain system and probe information Alternatively the user may enter a new subject and unique message directly Enter Next to get to the summary screen or Add Monitor to open a new monitor screen Meter 1 Configuration Wizard Type Analog Monitor Analog Input 1 5 A Email Send Configuration TO Address support wateranalytics net X Enter many email addresses separated by Subject Trouble at the WA Fish Tank Message The pH of the
46. or the probe that is in the alarm condition In the detailed screen the particular monitor line that is in alarm mode will be flashing red until acknowledged N116 133 AquaMetrix 2300 Installation and Operation Manual Page 22 2 Instead of green lights for the monitors on both the web probe status screen and the front panel quad screen the monitor in alarm condition will turn red Control type monitors will go from green to yellow when activated 3 Alarm events will be written into the Alarm Log including when the alarm was activated when acknowledged and when returned to normal mode In summary if you wish to the front panel to show an alert on the front panel use the alarm monitor if you only want to activate a relay or email use the control monitor There are eight standard choices of monitors plus the Analog Output when the optional analog output card is present see Section 13 4 From Figure 14 above they are listed here with explanations e High Control Activates relays and or notifications upon reaching a high level e Low Control Activates relays and or notifications upon reaching a low level e Fill Control Deactivates relays and or sends notification upon reaching a high level e Empty Control Deactivates relays and or sends notification upon reaching a low level e Low Alarm Same as Low Control but with alarm functions e High Alarm Same as High Control but with alarm functions e n Range Alarm Activates alarm and re
47. ot change any configuration or Acknowledge Alarms or Zero counters By default there is one user in the system named admin who has the Administrator access level During first time startup the administrator is asked for a new default password for this user At any time an Administrator may add additional users to the system and assign any of the above access levels Although an Administrator creates each user and their password each user is able to subsequently change their individual password Note that web users will be logged out automatically after a specified interval selected from the Setup gt System Configuration Browser Settings menu NOTE It is recommended that the admin password be changed from the default value to a different password to prevent unauthorized access to the system 7 2 Front Panel Passcodes and LCD Configuration Passcodes allow changes to the AquaMetrix 2300 from the front panel to be restricted to only those users who can authenticate the passcode Normally no passcodes are required This configuration is changed from the browser setup menu After accessing the Setup menu enter the System Configuration Menu followed by the LCD Configuration option This is shown below in Figure 21 The checkbox labeled Require Password on LCD should be checked and the change submitted After passcodes are enabled a different numeric passcode can be entered for each user in the User Maintenance Setup menu All changes a
48. outer This is because all routers are different and you will need to consult the manual for the router Usually the router s IP address will end in a 0 e g 192 168 1 0 If so then entering that number into the browser will take you to the router s home web page There are exceptions For instance an Apple Airport can only be accessed through the Airport Utility When using port forwarding operating the 2300 through a web interface is the same whether you are on your own LAN or outside it In both cases you use the external IP address with the port number There is one alternative to placing the 2300 on the WAN that some routers employ and that option is a so called DMZ The Demilitarized Zone is aptly named as it is a walled off section that sits between the LAN and WAN The DMZ is a more secure way of web enabling the 2300 as it does not allow the user access into your LAN Normally the DMZ allows only one local IP address to reside inside it To access a 2300 from a WAN in the DMZ simply enter the external IP address in a web browser i e do not add the colon and port number Inside your LAN connect to the 2300 via its local IP address Just remember that if your router uses DHCP and the local IP address of the 2300 changes you will need to change the IP listed in the DMZ accordingly If you have more than one 2300 in your LAN then you will need to revert to port forwarding for all or all but one 2300 9 3 Dedicated wireless connectio
49. played in the context menu The Email Keyword field is the value that is inserted into the Message text and indicates what value will be substituted when the alarm email is sent Table 4 Email Keyword List System Name systemname Name of the AquaMetrix 2300 sensor that sent the email message systemtime Time that the email message was sent sensorname Name of the Sensor that triggered the Alarm System IP Address systemip IP address of the AquaMetrix 2300 sensor that generated the Alarm Monitor Alarm Value alarmvalue Scaled value of the Sensor when the Alarm was generated N116 133 AquaMetrix 2300 Installation and Operation Manual Page 38 Monitor Name relayname Name of the Monitor relay or control that was triggered Sensor Value currentvalue Current scaled value of the Sensor at the time the email message was sent Description mdescrip Description that was entered during the configuration of the Sensor Control State relayresult ON or OFF state of the output relay at the time the email message was sent 10 5 Email To Addresses The final submenu is Email TO Addresses which list the previously entered Emails that are seen in the drop down menu when setting Monitor emails Next to each of these is a list of probes that have been set up with email notifications to each address New email addresses may be added here or existing ones deleted Text messages set up can be sent to sm
50. probes see Section 4 Set up the hardware probes first then use these defined probes to generate any virtual probes Monitors are set on the virtual probes just like the hardware probes New Probe Wizard Slot 5 Probe Selection Welcome to the Probe Configuration wizard where you select the type of Probe and which input or inputs to use Select the Probe type then one or more inputs dependnig on the Probe type selected If you are not sure of the different functions offered please consult the User s Manual Some inputs may not be available being previously assigned To free up a specific hardware input the Probe currently using it must be deleted from the Probe Configuration page Probe Type Select Probe Type Analog Probe Precision Pulse Input Probe Pulse Input Probe Totalizer Probe Analog Differential Probe Flow Dispenser Probe Manual Start Dispenser Figure 9 New Probe Wizard containing the probe definition The Analog Probe is one of the four 4 20 mA current inputs The Precision Pulse Input Probe is used to monitor a pulsed based signal from Digital inputs one or two It measures the time of each input waveform and converts it into a frequency that can be scaled The Precision Pulse Input Probe can measure input signals up to 20 Khz with a resolution of 100ns The Pulse Input Probe is similar to the Precision Pulse Input Probe except it measures the number of pulses received in a one second interval and therefore may
51. re is very useful with the optional relay cards to show how to wire up the relay it is shown in Figure 16 In this figure there is a six relay card and a four analog output card shown Only Relays 2 and 4 are available for selection as the others are previously defined N116 133 AquaMetrix 2300 Installation and Operation Manual Page 23 Meter 4 Configuration Wizard Type Precision Flow Digital Input 1 6 First Monitor Configuration Monitor Name Flow too high Monitor Type High Alarm None External ACK Control H Relay 4 Email Onl a Select Relay None Alarm ON 90 Alarm OFF 85 Send Email O No Email Send at Alarm ON Point Add Monitor Cancel Summary Figure 15 Probe Configuration Wizard page 6 Relay drop down menu Select Relay so 2 eee Gc ji DT DIRE Le o 2 i ae ud In In f E a SLS z La fno c nc no c nc 5a 5b 5a 6a 6b 6a AN AN AN AN 24v 24v ind in2 in3 m4 GND Figure 16 Probe Configuration Wizard page 6 Select Relay Relay 2 is selected red shading Relay 4 is available yellow outline Click inside yellow outline to select Relay 4 instead The next step is to enter the control trip points There are two inputs needed the trip point to activate the relay and the trip point to reset or deactivate the relay Both are in the scaled N116 133 AquaMetrix 2300 Installation and Operation Manual Page 24 calibrated units selected for the probe For a high alarm or control
52. re logged into the System Access log If the passcodes are unique for each user the user name performing the operation will also be logged There are other menu locations where a passcode is always required these are for factory setup only Contact Water Analytics Support for help Error Reference source not found shows other options available in this dialog box N116 133 AquaMetrix 2300 Installation and Operation Manual Page 29 LCD Configuration LCD DISPLAY CYCLE 2 TIME SECONDS START LCD PANELS 4 ON HOLD SHOW SYSTEM STATUS ON LCD REQUIRE PASSWORD ON LCD k Submit Cancel Figure 21 LCD Configuration Dialogue 8 Operating the 2300 without a Network The 2300 may be operated with or without a network connection but web access and email notifications will not be available for the latter However logs will still be compiled and temporary network access will allow these to be downloaded Once set up the 2300 will allow front panel setting of relay trip points and calibrations making network access not necessary for controlling and monitoring actions by the 2300 Front panel control and functions are described in Sections 1 3 and 1 4 Calibrating probes and changing relay set points via the front panel are described below Note that only the linear 2 point calibration and K Factor are supported on the front panel non linear and scaling factors may not be changed except via a network Saving and res
53. ssessrrrssersrersereserrsrresressersseeserrsserseersrreseeesereseee 20 4 2 Configuring Differential Sensors nennen enne nnne nnns nnns 21 4 3 Configuring a Flow Sensor for Batch Control eese 21 5 Configuring Alarms Relays and Notifications eene 22 bol Types oi MONTO Sansa bct bbaup catenncsa tess ead vanced snos sq Uca US OE MEI S D e Cu UR Sd cu PINK OPAC ES pest 22 N116 133 AquaMetrix 2300 Installation and Operation Manual Page 3 9 4 6 1 6 2 7 1 7 2 8 1 8 2 8 3 9 1 9 2 9 3 9 4 10 10 1 10 2 10 3 10 4 10 5 10 6 11 DI 11 2 11 3 11 4 11 5 12 13 13 1 13 2 13 3 13 4 14 15 Configuring for Email Notification cccccccsccccsseccssccenccceececenecceececeucessnecseneetsneceseeseneaes 26 L ss ann Da LOBO ec cee ipi doi EDU seen MIU MI UEM NM CEU 27 Data Logging Configuration Wizard esssseesseeeeseeeeeeeeeenene nnne nnn nnne nan 28 PVN Re MR MEE m TUR 28 User Maintenance and Passwords ener rennen nnnm en ns 29 Ma ogni elfe ORDER 29 Front Panel Passcodes and LCD Configuration ccccccccssecceeseeecceneceeeesenseeeeeeesteneeeeeeees 29 Operating the 2300 without a Network eere 30 Front Panel Calo haul o PEOR ETE 30 Front Panel Relay Seth elt ERE ia EEEE ENa 32 Front Panel Save and Restore Configuration cccc
54. st be done to recover from a corrupt internal SD card First you need to perform a rebuild operation If the SD card has had the web browser files corrupted or the SD card cannot be read the only option is to use the Rebuild SD Card option on the advanced LCD menu The second step is to restore the configuration from the backup The LCD rebuild is required because if the internal SD card is inaccessible the user won t be able to start the rebuild process from the advanced setup web page The Rebuild operation whether done from the LCD or web page requires that the Update SD card be inserted before it proceeds The rebuild operation performs the following 1 Reformats the internal SD card 2 Copies all web files html JavaScript and images from the Update SD card 3 Creates the basic directory structure required by the 2300 The next action requires that the user choose Restore from SD Card to copy the configuration from the removable SD Card back to the internal SD Card Once that has finished and the 2300 restarts the system is fully operational In addition if the system sees that the internal SD card is not accessible during startup the user is prompted to perform the rebuild operation N116 133 AquaMetrix 2300 Installation and Operation Manual Page 44 15 Panel Mounting Dimensions MINIMUM LEARENC INTERIOR FRONT VIEW SIDE VIEW TOP VIEW DIMENSIONS Max Panel 0 3 In 3 65 MOUNTING HARDWA
55. t Panel Relay Set Points If a relay is previously setup via the Monitor page in the Probe Configuration Wizard the set point values for trigger and reset may be changed on the front panel From the quad Run screen hit the right arrow and then down arrow to arrive at the detailed screen of the probe you want to modify Hitting Enter will bring up a menu for this probe shown below Relay Set Points e O O o D t X i Multi Parameter Controller Figure 25 Detailed screen and Meter Actions screen for Tank pH probe Select Relay Set Points to modify the relay trip point and reset a screen shown on the left in Figure 26 Choose which point to modify and get a numeric keypad entry screen shown on the right If the 2300 asks for a passcode just hit the back navigation button The saved value is Shown in parentheses Hit Done to save the value entered N116 133 AquaMetrix 2300 Installation and Operation Manual Page 32 Change Trip Pt 8 00 Change Reset Pt 7 50 Multi Parameter Controller fe E O O o S E u i in Figure 26 Change screens for relay trip and reset points 8 3 Front Panel Save and Restore Configuration Once the 2300 has been configured with probe definitions and email and server set ups these settings may be saved to an external microSD card via the front panel menu Carefully insert a microSD card in the rear slot not the easiest insertion Start with Menu s
56. te from the Internet The user may input the local time zone and whether daylight savings time is enabled N116 133 AquaMetrix 2300 Installation and Operation Manual Page 39 There is another user selected option on this menu Automatically enable all probes at startup Clicking this box allows the 2300 Controller to come online after a power outage with all probes enabled Without this box checked the Controller will power up with an Enable Probe screen requiring the user to respond to determine which if any probes are enabled This latter option is the default as the user must ensure that the controller relays will power up without start up problems after a power outage 11 2 Browser Configuration and Logging Out The second submenu is the Browser Configuration The first input is the refresh interval for the web browser By default the 2300 will refresh the Probe Status web page every 5 seconds The second and third inputs are the auto logout times for Administrators and Users respectively These are the durations for the 2300 to automatically log off the web connections These have defaults of 300 seconds 5 minutes and 1800 seconds 30 minutes respectively Change these as needed to fit into your operation Alternatively use your browser to remember your password in order to quickly log back in if disconnected The 2300 will remain in the state it is left in via the web If in the middle of a menu operation be sure to hit cancel
57. ted N116 133 AquaMetrix 2300 Installation and Operation Manual Page 40 e TO Address This is the email address used for sending the above error messages The drop down menu lists the email addresses previously entered into the 2300 and the top menu option allows a new address to be added 11 5 Unit List The last submenu is called Unit List and provides a list of the probe unit values in the system New units may be added here or during the Probe Setup Configuration Wizard Unwanted units may be deleted via this menu The 2300 is factory set with a list of units shown on the right in Figure 28 Unit Values mV pH cm EAS l min gal min 2 n y 4 5 6 ris 8 9 Figure 28 The Unit List display on the left and the list of factory installed units on the right 12 Advanced Setup Advanced setup consists of a group of miscellaneous functions Go to Setup Advanced to bring up a submenu that will allow you to perform the functions listed in Table 5 N116 133 AquaMetrix 2300 Installation and Operation Manual Page 41 Table 5 Advanced set up parameters List logged in users Provides a current listing of the users logged into the 2300 Prepare for shutdown Safely closes log files to prevent possible corruption also available on front panel menu Restart system Powers down system and reboots also available on front panel menu lO status List of current inputs with scaled outputs Restore to factor
58. toring the unit s configuration is described in Section 8 3 while setting up the unit s IP address is described in Section 9 8 1 Front Panel Calibration Hit Menu the go down one line to Calibrate Disable Probe and hit Enter to get to a list of the defined probes Use the navigation buttons to select the one you want to calibrate and hit Enter A new menu appears with two choices shown in the left portion of Figure 22 below Enable Disable Probe and Perform Calibration Choosing the former will allow you to toggle the probe from enabled to disabled and back again Choose calibrate and hit Enter to show the right portion of Figure 22 This screen displays the existing calibration points for this probe with the input current on the left and the value readout to its right Each point can be modified or left alone changing any value and selecting Done scroll down to see will update the calibration points and reset the calibration date N116 133 AquaMetrix 2300 Installation and Operation Manual Page 30 12 490mA 7 0 Modify First Point 15 750mA X 10 0 Modify Second Point APN Figure 22 Menu pages for the probe in slot 1 Tank pH showing the first calibration page Multi Parameter Controller Multi Parameter Controller Selecting to modify either point will bring up the screen below in Figure 23 Here you can enter the mA current and solution values that may be known for the probe or you can doa live calibration using the measur
59. uckets bottles or thimblefuls per unit time 4 Configuring Virtual Probes 4 1 Configuring a Totalizer Sensor The Totalizer Sensor is used to count the number of power cycles or pulses on one of the digital inputs It may be used to monitor the amount of time a piece of equipment is operating or totaling a flow to monitor the volume of fluid over a period of time The Totalizer can be used to trigger an alarm alert or relay when a volume or total has been exceeded or every time a pre set periodic count is reached e g if set to 100 will alarm at 100 200 300 etc The Totalizer may be based on an input previously configured such as flow or be used to configure the input itself The former method allows the current rate to be displayed and monitored by its own alarms in addition to the totalizer function Thus the Totalizer is a virtual sensor relying on another probe in the 2300 Controller The start point of the Totalizer can be set to zero using one of the contact inputs C1 through C4 or from either the web or the front panel The web reset is via the Probe Status page by clicking on the Config button to the top right of the graph and then choosing Reset Totalizer Front panel reset is via the Run screens press the Right Arrow to get to the detailed screens the hit Enter to see the reset option The value of the Totalizer can also be scaled independently of the flow probe it is based upon so that flow can be set in units such
60. umbered one to eight and each occupy a Slot They must also have a name associated with them that is displayed on the LCD front panel as well as on the web pages that show the status of each Probe Each Probe may also have one or more relays that it controls You can assign one of the relays to a Probe and use if to control a pump to fill or empty a tank You can also assign a relay that can act as either a high or low limit alarm Each relay can have a Trip point as well as a reset point When the value crosses the Trip point the relay turns on When the Reset Trip point is crossed the relay turns off By using proper Trip and Reset Trip points you can configure hysteresis for the relay and not cause chatter Click here to add new Meter Click here to add new Meter Click here to add new Meter Not Configured Click here to add new Meter Not Configured Click here to add new Meter IE Not Configured Not Configured Click here to add new Meter Not Configured Click here to add new Meter Not Configured Not Configured Click here to add new Meter Enable Disable Delete Cancel Change Display Order Figure 8 Probe Configuration web page 3 4 The Probe Configuration Wizard Selecting a slot from the Probe Configuration page 1 brings up the Probe Configuration Wizard The Probe Configuration Wizard screens contain instructions to guide you along the configuration process The order of this process is as f
61. utputs The status light is green for normal operation yellow for an activated relay and red for an activated alarm The Right Arrow brings up a detailed screen shown on the right side of Figure 1 This screen lists the monitor outputs for this probe including the monitor description and set point value along with the Last Calibration date The monitors are color coded with green for normal operation red for alarm condition and yellow for an activated relay N116 133 AquaMetrix 2300 Installation and Operation Manual Page 6 Pressing the Down arrow will cycle through all of the individual probe screens Pressing the Enter button will bring up a Meter Action screen allowing the user to acknowledge an alarm if active or setting relay trip points Run button will bring up the Run screen once again AquaMetrix 2500 AquaMetrix 2300 Tank pH Tank ORP 7 35 amp 386 gt pH e mVe o Tank D O Tank Level Multi Parameter Controller Multi Parameter Controller Figure 1 The Run display on the left reports 4 process values at a time If there are more than 4 pressing the down button reveals these The identical image appears on the web browser The Detail display on the right shows the detailed status of the Tank pH condition 1 4 Front Panel Menu The front panel menu is limited to a select group of functions The outline of this menu structure is below with descriptions 1 Main Mer View System Info Unit name IP addr
62. while still logged in If using the remote display mode go to the RUN screen prior to logging out If a probe is being configured when the administrator or editor is logged out it will stay in the edit mode and the probe will stay disabled To correct this situation log into the unit and go to edit the disabled probe you will receive a warning to override the existing edit say yes to take over the edit mode and just hit cancel to return the probe to the enable state 11 3 LCD Configuration The third submenu is called LCD Configuration which establishes whether or not the Controller s front menu system is locked out pending input of a PIN See Section 7 2 for details 11 4 Error Handling The fourth submenu Error Handling sets up email notifications for I O communication errors or for out of range errors from the analog probes These are trouble alerts that may be sent to email or as text messages to smart phones to alert an employee that an error has occurred Check boxes include e Send Email for I O Communications Error Alerts the email recipient of an I O error e Send Email for Out of Range 4 20mA Reading Alerts the email recipient of an out or range error for one of the analog probes This is essentially a trouble alert that a probe may have failed and isn t providing a valid reading e Send Email when GPS location changes This is not active in the standard 2300 unit and is only used in the 2300RT model currently being tes
63. ws the user to acknowledge an alarm or to set high and low axis values An example is shown is Figure 3 Alternatively clicking on the graph brings up a new window with just the graph The Previous and Next buttons allow the user to view data from the entire day s log in 15 minute increments The line represents the actual reading while the light shading around the line indicates the high and low range of the data for that interval The bar at the bottom is a time scale and the line in it can be dragged to the time period desired The left and right arrows on this bar are used to move the time frame by 45 minutes per click N116 133 AquaMetrix 2300 Installation and Operation Manual Page 8 Agua EA Metrix Remote 2300 Display Logs Setup Logout Refresh Graphs Probe Status Tank pH Tank ORP Config 7 12 pH FN 315 mv 20 20 20 25 20 30 20 20 20 25 20 30 Last Calibration 1 17 2014 Last Calibration 2 13 2014 Tank Conductivity Tank D O 0 481 89 3 sa 0 25 0 20 0 15 0 10 20 20 20 25 20 30 20 20 20 25 20 30 Last Calibration 2 13 2014 Last Calibration 2 13 2014 Figure 2 Probe status screen The screen lists all enabled sensors Meter Info Tank pH Overview An Analog Monitor measures values coming from an Analog input Alarms can also be configured to generate an email or dose an output relay at a High watermark Low watermark and In Range or Out of Range calculations Description Axis Minimum es EN
64. y defaults Brings up a confirmation screen to reset the 2300 to factory default settings Reformat amp rebuild Main SD card Repairs a corrupted SD card 13 Available I O Card Types The 2300 controller contains one expansion on the back that can be populated with any of the I O cards listed below In order to insert a card into a unit you must remove the plastic punch out that covers the slot and then remove the rear of the unit The card slides in being aligned by the two slots on each side 13 1 3 channel Digital Input 4 channel Digital Relay Output card The 3 channel Digital Input 4 channel Relay Output card is included with the 2300 standard model A second card brings to 6 the number of digital inputs and to 8 the oe we NN XO ce Q a VA R Xo PS P PA A N 3 Oa ou ce x SN S S S S SS NS Figure 29 3 Input 4 Relay Output Card connections number of normally open relay outputs The additional relays and digital inputs will appear in the drop down menus as numbers 5 8 and 4 6 respectively In addition they can be used as an external Acknowledge input for an Alarm N116 133 AquaMetrix 2300 Installation and Operation Manual Page 42 13 2 6 channel Relay Output card The 6 channel Relay Output card provides four normally open relay outputs and two relay outputs that have both normally open and normally closed contacts with the following connections DDDBEDOD oooga XS SONS S SES oN e M 2 i oe

AquaMetrix 2300 - Lesman Instrument Company

Contents

Download Pdf Manuals

Related Search

Related Contents