4x4 DVI Dual Link Matrix
Contents
1. 17 1 W x 1 7H x 4 25 D Hack NIOUNISDIE nenne ee 1U Rack Space 7 Lbs 11 WARRANTY Gefen warrants the equipment it manufactures to be free from defects in material and workmanship If equipment fails because of such defects and Gefen is notified within two 2 years from the date of shipment Gefen will at its option repair or replace the equipment provided that the equipment has not been subjected to mechanical electrical or other abuse or modifications Equipment that fails under conditions other than those covered will be repaired at the current price of parts and labor in effect at the time of repair Such repairs are warranted for ninety 90 days from the day of reshipment to the Buyer This warranty is in lieu of all other warranties expressed or implied including without limitation any implied warranty or merchantability or fitness for any particular purpose all of which are expressly disclaimed 1 Proof of sale may be required in order to claim warranty 2 Customers outside the US are responsible for shipping charges to and from Gefen 3 Copper cables are limited to a 30 day warranty and cables must be in their original condition The information in this manual has been carefully checked and is believed to be accurate However Gefen assumes no responsibility for any inaccuracies that may be contained in this manual In no event will Gefen be liable f2. TX and 5 Ground are used on the 5 232 serial interface Binary Table ASCII Corresponding Binary ASCII Corresponding Binary RMT16 IR RMT16 IR Button Button 00110001 9 9 00111001 00110010 10 0100001 00110011 b 11 0100010 4 4 00110100 c 12 5 5 00110101 d 13 6 6 00110110 e 4 onoo _7 7 omom f 155 onoono 8 8 01100 j g 6 0100111 RS232 Settings sweep E 19200 Bed CAMA o ao er E 8 1 FOW CONTO RACK MOUNT INSTALLATION Rack mount ears are provided for installation of this unit into a 1U rack mount space Locate the side screws on the unit Remove the front 2 screws that are located closest to the front of the unit Using the removed screws screw the rack mounting bracket into the unit Repeat the procedure on the opposite side of the unit Front of unit Rear of unit 10 SPECIFICATIONS Video Amplifier Bandwidth 2x 165 MHz Input Video Signal ee ee ee een 1 2 Volts p p ajo 0 M DIE SION Al RR 5 Volts p p TTL Dual Link Maximum Video Range 3840x2400 DVI Connector ee DVI I 29 pin female digital only POV ST OO 5V DC O 6A Power Consulares ee 30 Watts max DIMENSION E
3. R Extension Port Connect an optional IR extension part EXT RMT EXTIR to this port Power LED Indicator This LED will become active once the included 5V DC power adapter is properly connected RS 232 Serial Control Interface Use the commands on page 9 to control the 4x4 DVI DL Matrix using the RS 232 interface DVI Input 1 Connect a DVI DL source to this input DVI Input 2 Connect a DVI DL source to this input DVI Input 3 Connect a DVI DL source to this input DVI Input 4 Connect a DVI DL source to this input DVI Output 1 Connect a DVI DL display to this port DVI Output 2 Connect a DVI DL display to this port DVI Output 3 Connect a DVI DL display to this port DVI Output 4 Connect a DVI DL display to this port Locking 5V DC Power Adapter Input Connect the included 5V DC power adapter to this port 5 CONNECTING AND OPERATING THE 4X4 DVI DL MATRIX How to Connect the 4x4 DVI DL Matrix 1 Connect up to 4 DVI DL sources to the 4x4 DVI DL Matrix input ports using the supplied DVI DL cables 2 Connect up to 4 displays to the 4x4 DVI DL Matrix output ports using user supplied DVI DL cables 3 Connect the supplied 5V DC power supply to the 4x4 DVI DL Matrix 4 Power on the displays 5 Power on each source individually ensuring that a display is pointing to it while the power on procedure completes NOTE It is extremely important to ensure that when each source is being powered on it has a display poi
4. a Gefen YA SC 4 DVI Dual Link Matrix EXT DVI 444DL User Manual Www gefen com ASKING FOR ASSISTANCE Technical Support Telephone 818 772 9100 800 545 6900 Fax 818 772 9120 Technical Support Hours 8 00 AM to 5 00 PM PST Monday thru Friday PST Write To Gefen LLC c o Customer Service 20600 Nordhoff St Chatsworth CA 91311 www gefen com support gefen com Notice Gefen LLC reserves the right to make changes in the hardware packaging and any accompanying documentation without prior written notice 4x4 DVI DL Matrix is a trademark of Gefen LLC 2011 Gefen LLC All rights reserved All trademarks are the property of their respective owners Rev X3 CONTENTS 1 Introduction Operation Notes Features Panel Layout Panel Descriptions Connecting And Operating The 4x4 DVI DL Matrix OU Bb WO Configuring The 4x4 DVI DL Matrix RS 232 Serial Control Interface 10 Rack Mount Installation 11 Specifications 12 Warranty INTRODUCTION Congratulations on your purchase of the 4x4 DVI DL Matrix Your complete satisfaction is very important to us Gefen Gefen delivers innovative progressive computer and electronics add on solutions that harness integration extension distribution and conversion technologies Gefen s reliable plug and play products supplement cross platform computer systems professional audio video environments and HDTV
5. f quality e Discrete IR Remote included e Supports video resolutions up to 3840x2400 e Supports DDWG standards for DVI monitors e Includes rack ears Package Includes 1 4x4 DVI Dual Link Matrix 1 RMT 16IR 1 5V DC Power Supply 4 6 Foot Dual Link DVI cables 1 Set Of Rack Ears 1 User s Manual PANEL LAYOUT Front Panel 2 3 4 Back Panel 10 11 12 13 14 15 16 17 PANEL DESCRIPTIONS Display 1 Selected Source LED The array of 4 LED s correspond to the 4 source inputs on the back panel of the 4x4 DVI DL Matrix The currently selected source being displayed on DVI Output 1 will be indicated by an active LED Display 2 Selected Source LED The array of 4 LED s correspond to the 4 source inputs on the back panel of the 4x4 DVI DL Matrix The currently selected source being displayed on DVI Output 2 will be indicated by an active LED Display 3 Selected Source LED The array of 4 LED s correspond to the 4 source inputs on the back panel of the 4x4 DVI DL Matrix The currently selected source being displayed on DVI Output 3 will be indicated by an active LED Display 4 Selected Source LED The array of 4 LED s correspond to the 4 source inputs on the back panel of the 4x4 DVI DL Matrix The currently selected source being displayed on DVI Output 4 will be indicated by an active LED IR Receiver This IR receiver will receive commands from the included RMT 16 IR remote control I
6. iew the table below to set the channel on 4x4 DVI DL Matrix and IR remote control The remote channel for the RMT 16 IR is located underneath it s battery cover RMT 16 IR REMOTE CONTROL 4x4 DVI DL Matrix Remote Channel 1 Remote Channel 2 Remote Channel 1 Remote Channel 2 Default Default 1 2 1 2 1 2 1 2 Remote Channel 3 Remote Channel 4 Remote Channel 3 Remote Channel 4 T 2 1 2 1 2 1 2 CONFIGURING THE 4X4 DVI DL MATRIX AUTOMATIC LINK SELECTION DUAL LINK ONLY MODE The 4x4 DVI DL Matrix has the ability to run both Single Link and Dual Link sources There is a feature that will either automatically select the link mode or lock the unit in Dual Link mode By default Dip Switch 3 is in the OFF position Automatic Link Selection Turning Dip Switch 3 to the ON position will lock the unit in Dual Link mode and will only allow Dual Link signals to pass properly PRE EMPHASIS Pre Emphasis is used to help extend a signal travel over a distance of cable When a DVI cable connected to a display is over a long cable it is recommended that Pre Emphasis be enabled Pre emphasis is enabled by default on all display outputs For short cables disable pre emphasis on each output by turing it s corresponding Dip Switch to the ON position If any type of extension device is used pre emphasis must be disabled for proper operation RS 232 SERIAL CONTROL INTERFACE 94321 9876 mm Only Pins 2 RX 3
7. nting to it Most sources require a definite requirement if computers are being used a display to be attached to receive EDID display information and to begin operation If a source does not have a display that is pointing to it a video image may fail to be displayed It is recommended that each source be powered on and verified that it is outputting video before moving on to power the next source CONFIGURING THE 4X4 DVI DL MATRIX The 4x4 DVI DL Matrix has a bank of 8 configuration DIP SWITCHES These switches are located underneath the unit Peeling back the black metallic sticker on the bottom of the 4x4 DVI DL Matrix will reveal the Dip Switch bank These service switches are used for a number of configuration options By default all Dip Switches are in the OFF position Each setting is outlined below ON OFF 1 2 3 4 5 6 7 8 Switch 1 IR Remote Channel Configuration Switch 2 IR Remote Channel Configuration Switch 3 Automatic Link Selection Dual Link Only Mode Switch 4 Not Used Switch 5 Pre Empahsis For Display Output 1 Switch 6 Pre Empahsis For Display Output 2 Switch 7 Pre Empahsis For Display Output 3 Switch 8 Pre Empahsis For Display Output 4 IR REMOTE CHANNEL CONFIGURATION Dip Switches 1 and 2 relate to the IR remote control channel that is used by the 4x4 DVI DL Matrix and RMT 16 IR remote control Dip Switch 1 and 2 on the 4x4 DVI DL Matrix must match Dip Switch 1 and 2 on the RMT 16 IR remote control Please v
8. or direct indirect special incidental or consequential damages resulting from any defect or omission in this manual even if advised of the possibility of such damages The technical information contained herein regarding the features and specifications is subject to change without notice For the latest warranty coverage information please visit Gefen s Warranty web page at http www gefen com kvm aboutus warranty jsp PRODUCT REGISTRATION Please register your product online by visiting Gefen s web site at http www gefen com kvm Registry Registration jsp 12 Rev X3 444DL ma DVI 20600 Nordhoff St Chatsworth CA 91311 1 800 545 6900 818 772 9100 fax 818 772 9120 www gefen com support gefen com E e Qu
9. systems of all sizes with hard working solutions that are easy to implement and simple to operate The Gefen 4x4 DVI DL Matrix Easily combine any four cross platform Dual Link DVI video display outputs and four Dual Link DVI digital displays without networking Our 4x4 DVI Dual Link Matrix provides a simple reliable and highly effective method of creating multiple Dual Link DVI display consoles with each console capable of accessing any one of the Dual Link DVI video sources at any time by remote control You also have the option of setting up the four displays locally or extending them with a Gefen extender How It Works The 4x4 DVI Dual Link Matrix has four Dual Link DVI inputs and four Dual Link DVI outputs You simply connect your four Dual Link DVI video sources to the Switcher s inputs then connect your four Dual Link DVI displays to the Switcher s outputs OPERATION NOTES READ THESE NOTES BEFORE INSTALLING OR OPERATING THE 4X4 DVI DL MATRIX The 4x4 DVI DL Matrix does not have any scaling functionality All of the attached monitors must be able to display the attached sources resolution For maximum compatibility it is recommended that only one compatible common resolution for all displays be used by all sources FEATURES Features e Increases your productivity by letting you view any four Dual Link DVI video sources on any four Dual Link DVI displays e Maintains highest resolution digital video with no loss o
Download Pdf Manuals
Related Search