Multi-functional Programmable Controller CE-PTZ
Contents
1. display shown below You can also access the PTZ menu by pressing the button MON CAM ALM 001 0001 0001 Select Change current camera By default the keyboard usually starts in PTZ mode display shown below You can also access the PTZ menu by pressing the MENU button CAM 601 0001 0001 Change selected camera Preset Function Add Preset ENTER 1 to 255 Call a Preset HIENTERI 1 to 255 Delete a Preset JENTER 1 to 255 The maximum preset number depends on the PTZ device Please refer to the user s manual for further information SET SHOT 001 0001 0001 001 0001 0001 Tour Sequence A sequence can store up to 24 preset points with individual dwell times and speeds You can store a sequence by using this function Only available in BO1 BO2 Protocol Press GRP SET 1 to 4 After entering sequence programming mode the display shows the preset input and settings for speed and time Seq Sequence number z Pos Preset number eq Pos Spd Ti Spd Move speed between 1 8 Ti Stop time between 0 60 sec Press ENTER to confirm and save the setting Repeat the preset position input with speed and time settings and confirm with ENTERI After exiting the programming mode the settings will be saved to the dome s memory Working with DVR Enter DVR mode To control DVR press the DVR Button and enter the DVR mode The LED with DVR tag indicates the current2. message will appear on screen when changes are saved or your submission is correct An ERROR message will appear on screen when an incorrect password is entered 18 CLOCK SETTING 13 44 30 10 03 31 COMM SETTING S N XXXXXXXXXXXXXXX CONF XXXXXXXXXXXXXXX SITE ID 001 COMM SPEED 9600bps PROTOCOL CLINTON BACK DEXIT MAIN MENU SYSTEM SETTING gt D CAMERA SETTING gt FUNCTION SETTING gt WINDOW BLANKING gt EXIT CAMERA SETTING DIGITAL ZOOM BLC MODE SLOW SHUTTER ADVANCE SETTING BACK EXIT ZOOM SPEED DIGITAL ZOOM BLC MODE SLOW SHUTTER DADVANCE SETTING gt BACK EXIT AE MODE SHUTTER IRIS BRIGHT WB MODE R GAIN B GAIN D BACK EXIT CLOCK SETTING The system is equipped with a RTC Real Time Clock and can be used to display the date time information on the screen or operated via schedule see pg 18 Time Running In order to use this function correctly you must first set up the date and time TIME Change the time setting Displayed as 24hr clock DATE Change the date setting Displayed as Year Month Day BACK Move to previous screen doing so will save your changes to clock setting EXIT Exit the OSD doing so will save your changes to clock setting COMM SETTING To edit settings for Site ID baudrate and protocol you must first unlock these settings by entering the serial number again into the CONF field Protocol setting can be detected
3. 00 0 00 00 0 00 00 0 00 00 0 00 00 0 00 00 0 00 00 0 00 Model Signal Format Scanning Image Sensor H Resolution Viewing Angle Zoom Min Illumination Focus White Balance Shutter Speed Iris Control Gain Control Video Output S N Ratio Pan Speed Tilt Speed Pan Range Tilt Range Communication Preset Positions Auto Pan Tour Sequence Privacy Mask Operating Temp Power CE PTZ10X PAL NTSC Progressive 1 4 inch Ex View CCD 540 TVL 46 0 Wide end 4 6 Tele end 10 x Optical 12 x Digital 1 0Lx typical F1 8 50 IRE Auto Manual Auto Manual ATW Indoor Outdoor One Push WB Manual WB 1 to 1 10 000 Sec 22 steps Auto Manual Auto Slow Shutter Auto Manual 3 to 28 dB 2 dB steps VBS 1 0Vp p Sync Negative Y C Output More than 50 dB 0 4 300 per Sec 0 4 150 per Sec 360 0 90 RS 485 multiple protocol coax 128 Presets Yes between 2 presets 4 progr Tours with max 32 presets 4 Patterns up to 180s 24 Position 8 Position per Screen Outdoor 40 F to 140 F Indoor 14 F to 122 F DC 12V AC 24V If you have trouble operating your camera and the guidelines in this manual do not enable you to solve the problem contact Clinton Electronics Technical Support at 1 800 549 6393 or 815 633 1444 23 CLINTON Electronics CLINTON Electronics CLINTON Electronics 6701 Clinton Road Loves Park IL61111 1 800 447 3306 Sales 1 800 549 6393 Support www
4. Move to previous screen doing so will save your changes to presets EXIT Exit the OSD doing so will save your changes to presets 20 DSCAN NUMBER SCAN SPEED SET LEFT LIMIT SET RIGHT LIMIT gt CLEAR SCAN RUN SCAN EDIT SCAN LABEL gt BACK EXIT PATTERNS PATTERN NUMBER PROGRAM PATTERN gt RUN PATTERN CLEAR PATTERN EDIT PATTERN LABEL gt SCAN A Scan Tour is an automated Pan movement between 2 defined positions with speed setting The scan will move from the defined Left limit to the defined Right limit in a straight path and back again If you wish to have your PTZ follow a more advanced path use one of the next two selections PATTERN or TOUR SCAN NUMBER Current scan number SCAN SPEED Define the scan speed SET LEFT LIMIT Define the left point of the scan tour To define enter the selection and move the PTZ to desired position Use IRIS OPEN to store or IRIS CLOSE to discard SET RIGHT LIMIT Define the right point of the scan tour To define enter the selection and move the PTZ to desired position Use IRIS OPEN to store or IRIS CLOSE to discard RUN SCAN This will run the current scan defined in SCAN NUMBER CLEAR SCAN This will erase the current scan defined in SCAN NUMBER EDIT SCAN LABEL Assign a name to the current scan defined in SCAN NUMBER BACK Move to previous screen doing so will save your changes to scan EXIT Exit t
5. PASSWORD OLD PASSWORD OLD PASSWORD ENABLE PASSWORD OFF BACK EXIT COMM SETTING S N XXXXXXXXXXXXXXX CONF XXXXXXXXXXXXXXX SITE ID 001 COMM SPEED 9600bps PROTOCOL CLINTON BACK EXIT MAIN MENU SYSTEM SETTING gt CAMERA SETTING gt FUNCTION SETTING gt WINDOW BLANKING gt EXIT CAMERA SETTING ZOOM SPEED DIGITAL ZOOM BLC MODE SLOW SHUTTER ADVANCE SETTING gt BACK EXIT FUNCTION SETTING PRESETS gt SCAN gt PATTERNS gt TOUR gt ZONES gt TIME RUNNING gt BACK EXIT PRESETS PRESET NUMBER SET PRESET gt SHOW PRESET CLEAR PRESET EDIT PRESET LABEL gt SCAN NUMBER SCAN SPEED SET LEFT LIMIT gt SET RIGHT LIMIT gt CLEAR SCAN RUN SCAN EDIT SCAN LABEL gt BACK EXIT PATTERNS PATTERN NUMBER 001 PROGRAM PATTERN gt RUN PATTERN CLEAR PATTERN EDIT PATTERN LABEL gt TOUR NUMBER EDIT TOUR gt RUN TOUR CLEAR TOUR BACK EXIT ZONE NUMBER SET LEFT LIMIT gt SET RIGHT LIMIT gt CLEAR ZONE EDIT ZONE LABEL gt BACK EXIT TIME RUNNING TIME CHANNEL START TIME 00 00 END TIME 00 00 NONE WINDOW BLANKING WINDOW NUMBER EDIT WINDOW gt ENABLE WINDOW CLEAR WINDOW BACK EXIT EDIT PRESET LABEL LABEL PRESET 001 BACK EXIT EDIT SCAN LABEL EDIT PATTERN LABEL LABEL PATTERN1 BACK EXIT EDIT TOUR PO S TM PO S TM 00 0 00 00 0 00 00 0 00 00 0 00 00 0 00
6. automatically In this section the camera and image related functions can be set ZOOM SPEED Zoom in speed DIGITAL ZOOM Besides the optical zoom this PTZ is equipped with digital image enlargement known as digital zoom When off only the optical zoom will be available BLC MODE Backlight compensation mode Use this option when the observed object has a strong backlight such as sunlight or other light source SLOW SHUTTER The slow shutter allows a higher sensitivity by exposing the image sensor a longer period of time useful when observing objects do not have much movement ADVANCED SETTING Enters the advanced settings sub menu for the camera AE MODE Activate auto exposure mode for various exposure methods for different environments SHUTTER MODE In shutter mode the camera changes the shutter speed to regulate light IRIS MODE Regulate the iris opening to control the exposure BRIGHTNESS Regulate the exposure by changing the brightness control AUTO Automatically regulates the exposure modes WB MODE The camera supports Auto Manual ATW OPW Outdoor and Indoor modes of White Balance which chooses the correct color of the image NOTE R gain and B gain are only editable in Manual mode R GAIN Regulates the red elements in the image color B GAIN Regulates the blue elements in the image color 19 Function Settings MAIN MENU SYSTEM SETTING gt CAMERA SETTING gt DFUNCTION S
7. with the joystick will activate the following functions There are no sub menus to these functions You cannot undo the action CLEAR ALL ZONES Clear set zones CLEAR ALL PRESETS Clear all stored preset positions CLEAR ALL PATTERNS Clear all stored pattern tours CLEAR ALL TOURS Clear all tours CLEAR ALL WINDOWS Clear all privacy masking settings FACTORY DEFAULTS Reset all settings and return to factory settings RESTART Restarts the system used after resetting factory defaults BACK Move to previous screen EXIT Exit the OSD NOTE After using the FACTORY DEFAULTS option all system settings and stored information such as presets tour or patterns will be permanently erased Please make sure this is your intention before selecting this option PASSWORD SETUP In password settings menu you can change the password and enable disable the password protection function The password function can prevent unauthorized access to the OSD and changes to the settings It consists of a 6 digit number from 0 9 and can be disabled if so desired 1 To modify the password you must input the old password The default password is 000000 2 Enter anew password 3 Enter the new password again in CONF PASSWORD to confirm To set the password move left right to select a digit and up down to change the number When finished press IRIS OPEN on the keyboard or move the cursor right to save the settings A SUCCESS
8. Cut 9 Cut 16 Cut Zoom Slow Plavback Start Plavback Plavback Kev Pause Kev Stop Kev Rewind Kev Forward Kevboard Information Power ON OFF DVR Ch Display 14 0 9 Ch Display 0 0 9 Key Plus Key Minus Key Audio Key Search Key Next Clear Keyboard Screen Keylock Key Left Key Right Key Up Key Down Set Enter Hold Prev IRIS close Wide Tele Key Aux ALM ON Autopan IRIS Open GRP OFF Run 1 ENTER 0 ENTER 3D Joystick Right 3D Joystick Left Focus Near Focus Far DVR ID Setting CLR SHOT Joystick Left Joystick Right Joystick Up Joystick Down 14 Press NEXT button agin to change the assignment for the DVR input and Camera ID admin access required Note Setup the communitcation baud rate and ID in the DVR before connection To prevent signal interference it is strongly recommended to use an RS 485 distributor for connection Control Press the MUX button to enter the Multiplexer mode LED for MUX mode Press MUX button to enter Multiplexer mode PTZ with Multiplexer in MUX mode In MUX mode press the MUX button again to enter virtual PTZ mode You can control the PTZ by switching the input channel the camera ID will also be switched accordingly MUX ID 01 ID of the Multiplexer a e ha NO Input 1 ofthe Multiplexer jj IA Indicates the control of PTZ Cam 0001 Camera ID Setup the virtual PTZ control in MUX mod
9. ETTING gt WINDOW BLANKING gt EXIT FUNCTION SETTING DPRESETS gt SCAN gt PATTERNS gt TOUR gt ZONES gt TIME RUNNING BACK EXIT PRESETS PRESET NUMBER SET PRESET gt SHOW PRESET CLEAR PRESET EDIT PRESET LABEL gt BACK DEXIT In the function settings user can setup the automated PTZ functions such as preset position tours scan etc These functions mav become verv useful for vour surveillance application PRESET Preset point is a position of PTZ which can be memorized by the device and be recalled immediately if needed Up to 128 preset points are supported Quickly recall a preset using the keyboard by pressing SHOT the desired preset then ENTER NOTE Assigning 95 to a preset will result in an error as this number is used to call up the System Settings OSD Menu PRESET NUMBER Selected preset position SET PRESET Setup the preset position Enter this menu move the PTZ to desired position and press IRIS OPEN to store or IRIS CLOSE to discard SHOW PRESET This will show the current preset defined in PRESET NUMBER CLEAR PRESET This will delete the current preset defined in PRESET NUMBER EDIT PRESET LABEL Assign a name to the current preset position defined in PRESET NUMBER This label will show on the screen when called up Preset Label must be set to ON for label to appear on screen See pg 12 Display Setup BACK
10. Multi functional Programmable Controller CE PTZ KEY User Manual VER34 lt 01 gt SYSTEM KEYBOARD DVR QO amp SET SHOT ALM GRP OFF U U U O AUX RUN HOLD PREV N OUODD DOOR CLINTON Electronics 1 800 447 3306 Sales CLINTON Electronics 6701 Clinton Road 1 800 549 6393 Support www clintonelectronics com Loves Park IL 61111 1 800 633 8712 Fax Introduction Congratulations on the purchase of your new CE PTZ KEY This device is a multi functional programmable kevboard controller for Pan Tilt Zoom devices DVRs and Matrix devices and can be programmed with individual protocol settings for each connected device It is equipped with a 3 Axis joystick for performing Pan Tilt and Zoom with a single hand Main Features Manage up to 9999 devices Controls PTZ DVR and Matrix in different protocol with pre programmed settings 3 Axis jovstick e Multiplexer operation with DVR and PTZ e Password protected for administrative access e Supports major telemetric protocols e Dual serial interface with RS232 and RS485 e Supports major DVR brands e Aluminum construction e Ergonomic Design PACKAGE CONTENTS Si RJ 45 AU P12H CE PTZ KEY Keyboard Keyboard RS485 Plug 2 pin Keyboard AC DC Power User Manual Adaptor RS232 Plug 4 pin Cable Supply Installation and Set up Unpacking your keyboard Your keyboard comes with a power supply as well as a keyboa
11. PO S TM PO S TM Tour Editing 00 0 00 00 0 00 00 0 00 a oT 00 0 00 00 0 00 00 0 00 PO The preset position being included in the tour If there is no preset 00 0 00 00 0 00 00 0 00 position stored please exit and define presets before continuing 00 0 00 00 0 00 00 0 00 00 0 00 00 0 00 00 0 00 ee 00 0250 S The speed in which the PTZ moves to this preset The value is between 00 0 00 00 0 00 00 0 00 1 slow 8 fast 00 0 00 00 0 00 00 0 00 TM The dwell time before the PTZ moves to the next point Given in seconds Up to 60 sec RUN TOUR This will run the current tour defined in TOUR NUMBER CLEAR TOUR This will erase the current tour defined in TOUR NUMBER BACK Move to previous screen doing so will save your changes to tour EXIT Exit the OSD doing so will save your changes to tour ZONES The zone function allows user to define a perimeter with a name tag The ees perimeter is defined by setting a Left and Right end of a desired area When the SET RIGHT LIMIT gt camera enters this area the name will be displayed on the screen which provides he ii better orientation in surveillance applications Up to 8 zones are supported Make sure Zone Label is set to ON in Display Setup see pg12 IZONE NUMBERI Current zone number SET LEFT LIMIT Define the left point of the zone SET RIGHT LIMIT Define the right point of the zone CLEAR ZONE This will erase the current zone defi
12. TALLED AND USED IN ACCORDANCE WITH THE INSTRUCTION MANUAL MAY CAUSE HARMFUL INTERFERENCE TO RADIO COMMUNICATIONS OPERATION OF THIS EQUIPMENT IN A RESIDENTIAL AREA IS LIKELY TO CAUSE HARMFUL INTERFERENCE IN WHICH CASE THE USER WILL BE REQUIRED TO CORRECT THE INTERFERENCE AT HIS OWN EXPENSE CAUTION CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE COULD VOID THE USERS AUTHORITY TO OPERATE THE EQUIPMENT CE COMPLIANCE STATEMENT WARNING THIS IS A CLASS A PRODUCT IN A DOMESTIC ENVIRONMENT THIS PRODUCT MAY CAUSE RADIO INTERFERENCE IN WHICH CASE THE USER MAY BE REQUIRED TO TAKE ADEQUATE MEASURES CAUTION BEFORE ATTEMPTING TO CONNECT OR OPERATE THIS PRODUCT PLEASE READ THE LABEL ON THE BOTTOM AND USER S MANUAL CAREFULLY Technical specifications are subject to change without prior notice Manual may contain mistakes or print errors All trademarks mentioned belong to their respective owners Installation Safety Instructions before starting Do not install and operate this appliance in a flammable and explosive environment Make sure that the installation is done according to the local electricity safety regulations of your country Before installation and maintenance make sure that the appliance is disconnected from the power source Handle the device during installation carefully Falls or extreme vibration may cause irreparable damages or void the warranty Do not install o
13. Tilt movement 3 Extended Function Keys TURN Zoom in out ALM Alarm function GRP Tour function A OFF Function off Joystick Functions Navigation Zoom ON Function on AUTOPAN Auto pan function AUX Auxiliary function RUN Function start HOLD Hold ee ur A EN cur PREV Previous device DLEO Tor BEZ IN NEXT Next device Dan Initial Setup After power up the keyboard will start the initialization and self test The LCD VERXX lt 01 gt display will show initial startup screen Press MENU to start using the keyboard System Keyboard Startup Screen Main Operation Screen MON CAM ALM 001 0001 0001 Selected Selected Selected Monitor Camera Alarm Input To quickly use your connected PTZ camera you may have to type in the corresponding camera ID even if it already shows the correct ID ID 01 is default Press CAM 1 ENTER CAM 1 001 0001 0001 User Mode amp Admin Mode The keyboard will enter automatically into USER MODE after power up which allows performing PTZ and DVR control and restrict user access to keyboard setup menu Following message will show ADMIN AUTHORITY 001 0001 0001 Enter Administrator Mode 1 Press ON amp B at the same time a me 2 Enter your password with the number keys and confirm with JENTER default password 9876543210 Entering into Admin mode will allow you to set up device parameters as described in the next steps 3 To exit Admin mode the device must be powe
14. WINDOWI Edit the current masking window as defined in WINDOW NUMBER 1 Center the area you wish to mask on the screen by using the jovstick 2 Press iris open to enter window blanking edit 3 Use the UP and DOWN movements to increase or decrease the height of the window mask 4 Use LEFT or RIGHT to decrease or increase the width of the window mask 5 Press IRIS OPEN to save the mask CLEAR WINDOW Clear the current masking window as defined in WINDOW NUMBER BACK Move to previous screen doing so will save your changes to time window blanking EXIT Exit the OSD doing so will save your changes to window blanking 23 OSD Map OSD MENU INDEX SYSTEM SETTING EDIT DOME LABEL gt INITIAL INFO gt DISPLAY SETUP gt MOTION gt CLEAR gt PASSWORD SETUP gt CLOCK SETTING gt COMM SETTING gt LABEL DOME 1 BACK EXIT INITIAL INFO S N XXXXXXXXXXXXXXX CLINTON V2 42 PROTOCOL CLINTON DOME ADDRESS 001 COMM 9600 N 8 1 BACK EXIT DISPLAY SETUP DOME LABEL PRESET LABEL ZOOM LABEL ZONE LABEL DIRECTION LABEL TEMPERATURE LABEL OFF TIME LABEL OFF DATE LABEL OFF AUTO FLIP PROPORTION PAN PARK TIME PARK ACTION POWER UP ACTION FAN ENABLED BACK EXIT CLEAR ALL ZONES CLEAR ALL PRESETS CLEAR ALL PATTERNS CLEAR ALL TOURS CLEAR ALL WINDOWS FACTORY DEFAULTS OLD PASSWORD OLD PASSWORD OLD PASSWORD ENABLE PASSWORD OFF OLD
15. Wite c Connection Green Wire ko Monitor en Y ir yellow Wire I ABS S Je le pias Cab Aussee xa Y ae dapto oard A y sf with CE PTZKE Power supply 19 Wall Outlet RS485 Cable The telemetric control of the device uses RS485 serial communication with half duplex transmission technology The transmission distance can vary depending on cable type and baud rate The following table shows maximum distances based on cable with 0 56mm 24AWG twisted pair 2400 bps 5577ft 1700m 4800 bps 3609ft 1100m 9600 bps 2297ft 700m 19200 bps 1312ft 400m Due to environmental interfaces such as electromagnetic and induction fields or number of connected devices on the RS485 bus or using thinner than 24AWG cable the transmission range may be less Installation Star Connection The star form connection is most commonly used It enables the connection of different dome cameras with longer cable runs It is recommended to use an RS485 distributor to ensure the telemetric data transmission The advantage of the star connection is that every channel can work independently and can take a cable length up to 3 280 feet 1000 meters depending on cable quality In cases where more dome cameras are installed the star connection can be extended with additional RS485 distributors Video Cable Coaxial cable with 750 impedance with copper conductor at center conductor and shielded with 95 copper The followi
16. clintonelectronics com 1 815 633 8712 Fax v 09 23 11
17. e In MUX mode press AUTOPAN to change the selected Multiplexer Select the MUX ID for setup if more than one are installed and Set MUX ID choose the desired device 01 lt 00 66 gt MUX ID Monitor ID for Output ID 01 OUT 0001 Press AUTOPAN again to setup the PTZ admin access IN 01 CAM 001 required Press ENTER after every assignment to save the MUX Input Camera ID changes Failure to do so may result in the loss of the configured Channel n settings 15 Basic Operation Initial Screen and Self Testing After powered on the dome starts the self testing by slowly rotating and panning After the self test completes the initial information will be displayed on the screen S N XXXXXXXXXXXXXXX S N of the PTZ The initial information will remain on CLINTON V2 42 Software Version the screen until a button is pressed PROTOCOL CLINTON Protocol joystick is moved or until POWER UP DOME ADDRESS 001 Dome ID COMM 9600 N 8 1 ee ACTION initiates See next page on Communication h h Initial Info withi Parameter ow to show Initial Info within system settings menu and how to define Power up action Open the On Screen Display OSD Menu This dome supports OSD menu for simple configuration of device settings To enter the OSD menu press shot 95 enter on the keyboard Or call the sequence shot 9 enter twice within 3 seconds If you encounter troubles make sure your keyboard settings are correct for the cam
18. e controller from 0 to 15 Input the SET KEY LEVEL number by using the digit keys After setting press ENTER to save or CLR to exit the ar setting Monitor SET MON RANGE Setup the range of monitors from 0000 to 0239 Input the ENNEN number by using the digit keys After setting press ENTER to save or CLR to exit the gt 0000 gt 0239 setting Camera range SET CAM RANGE Setup the range of intelligent dome cameras from 0000 to 9999 mE Input the number by using the digit keys After setting press ENTER to save or CLR 0000229999 to exit the setting Alarm Range SET ALM RANGE Setup the range of alarm positions from 0000 to 9999 Input the SET ALM RANGE number by using the digit keys After setting press ENTER to save or CLR to exit the Tr setting Reset Default RESET DEFAULT 12 Reset the keyboard to factory defaults by entering the password default password 9876543210 Press ENTER to activate the reset or CLR to exit NOTE Pressing ENTER will clear all settings that have been saved on the device This process can take up to 30 seconds until the controller is available again Note that ifthe baud rate has been changed due to the reset it is necessary to restart the keyboard by removing the RJ45 cable from the back of the unit RESET DEFAULT 12 PASSWORD RESET DEFAULT 12 IKKKLAIRKAXX 9876543210 PLEASE WAIT 12 Working with PTZ Start PTZ mode By default the keyboard usually starts in PTZ mode
19. een doing so will save your changes to display setup EXIT Exit the OSD doing so will save your changes to display setup MOTION The motion control includes the setting for Park Time action and other features AUTO FLIP Disabling this function will limit the tilt range to 90 degrees only PROPORTIONAL PANI Pan speed adjusts accordingly to the zoom ratio The more the operator zooms in the slower the pan speed The Park Time speed will be adjusted accordingly PARK TIME Sets the idle time in minutes until PARK ACTION is activated PARK ACTION You can select an action that will be started after certain idle time such as preset tour or pattern Select NONE to disable the function POWER UP ACTIONI Instructs the dome to start a predefined action when system boots up and completes the self test This could be helpful to restore the observation after power loss FAN ENABLED Sets the temperature limit for the internal cooling fan to start BACK Move to previous screen doing so will save your changes to motion EXIT Exit the OSD doing so will save your changes to motion 17 CLEAR ALL ZONES CLEAR ALL PRESETS CLEAR ALL PATTERNS CLEAR ALL TOURS CLEAR ALL WINDOWS FACTORY DEFAULTS RESTART PASSWORD SETUP OLD PASSWORD NEW PASSWORD CONF PASSWORD ENABLE PASSWORD BACK D EXIT CLEAR The CLEAR function resets the stored settings and controls back to factory default NOTE Pressing Right
20. era you are trying to control such as the CAM number on your keyboard matching the number assigned to the desired PTZ Navigation from keyboard IRIS OPEN Enters the sub menu or confirms a setting IRIS CLOSE Exits the selected menu item or cancels the current setting UP DOWN Move between menu lines or adjust the selected value RIGHT Enter a highlighted menu item same as IRIS OPEN LEFT Moves left or exit the menu item System Settings MAIN MENU D SYSTEM SETTING gt CAMERA SETTING gt FUNCTION SETTING gt WINDOW BLANKING gt EXIT SYSTEM SETTING DEDIT DOME LABEL gt INITIAL INFO gt DISPLAY SETUP gt MOTION gt CLEAR gt PASSWORD SETUP gt CLOCK SETTING gt COMM SETTING gt BACK EXIT EDIT DOME LABEL DLABEL DOME 1 BACK EXIT EDIT DOME LABEL For multiple domes in a single installation it may be helpful to assign a name to every dome with location info Label may contain alphanumeric values up to 16 characters long Ensure Dome Label is set to ON see Display Setup on pg 12 Enter OSD and select SYSTEM SETTING Select EDIT DOME LABEL and enter the sub menu Select LABEL and enter with RIGHT or IRIS OPEN The input character starts to flash use UP or DOWN to select the desired character and RIGHT for next input Available characters appear in the following order 0 to 9 A to Z 7 lt ER SPACE Use LEFT
21. he OSD doing so will save your changes to scan PATTERN A pattern tour is a custom tour defined by recording the user s actions up to 180 seconds per tour This camera can support up to 4 pattern tours PATTERN NUMBER Current pattern number PROGRAM PATTERN Record the pattern tour Enter this menu to start the tour recording when finished press IRIS OPEN to store RUN PATTERN This will run the current pattern defined in PATTERN NUMBER CLEAR PATTERN This will erase the current pattern defined in PATTERN NUMBER EDIT PATTERN LABEL Assign a name to the current pattern defined in PATTERN NUMBER BACK Move to previous screen doing so will save your changes to pattern EXIT Exit the OSD doing so will save your changes to pattern 21 TOUR A Tour is an automated cruising through selected preset positions with individual speed settings and dwell times This PTZ supports up to 4 tours with 24 positions each NOTE Before a tour can be properly set up you must first define your RUN TOUR preset points you wish to include in the tour see page 16 Presets CLEAR TOUR A tour sequence will repeat until interrupted by a movement of the joystick BACK l l EXIT after it reaches a preset point or until another command is entered ie SHOT 95 ENTER to enter menu TOUR NUMBER Current tour number EDIT TOUR Edit the current selected tour as defined in TOUR NUMBER EDIT TOUR PO S TM
22. ned in ZONE NUMBER EDIT ZONE LABEL Assign a name to the current zone defined in ZONE NUMBER BACK Move to previous screen doing so will save your changes to zones EXIT Exit the OSD doing so will save your changes to zones 22 TIME RUNNING DTIME CHANNEL START TIME END TIME RUNNING BACK EXIT TIME RUNNING The time running function is a scheduled start for predefined action such as preset tour scan tour etc This PTZ supports up to 4 schedules Before setting this function please make sure that the system time has been set correctly see clock setting pg14 TIME CHANNEL Current schedule number START TIME Start time of selected schedule as defined in TIME CHANNEL END TIME End time of selected schedule as defined in TIME CHANNEL RUNNING Define the action to be started Select None to deactivate the function BACK Move to previous screen doing so will save your changes to time running EXIT Exit the OSD doing so will save your changes to time running Window Blanking The Window Blanking function is used to protect the privacy in the observed area as WINDOW BLANKING WINDOW NUMBER EDIT WINDOW gt ENABLE WINDOW CLEAR WINDOW BACK DEXIT this may be required by law for certain applications It is also known as Privacy Masking which covers the selected area with a blank window This PTZ supports up to 25 masking windows IWINDOW NUMBERI Current window number EDIT
23. ng table shows different cable type and its maximum length Cable Standard Max Distance m ft The values are for reference only Depends on the cable RG 59 U 750 ft 229m quality and environmental conditions the transmission RG6 U 1000 ft 305m distance might be less RG 11 U 1500 ft 457m If the cable length is more than 1 312ft 400m it is recommended to use optional accessories such as a video amplifier or twisted pair video converter for boosting the video signal Monitor Up to 750m coaxial cable optional Video Amplifier optional Extend connection distance with video amplifier RS485 Connection Balun Transmitter Balun Receiver optional optional Up to 1200m twisted pair or cat5 cable Extend connection distance with P Twisted Pair video converter RS485 Connection optional Installation Key Description LCD Display with backlight 4 Digit Pad 1 Camera Operation Keys 4 Digit Pad Zoom WIDE TELE Zoom in and zoom out FOCUS FAR NEAR Manual focus IRIS OPEN CLOSE Manual iris 0 9 Digit input from 0 to 9 Star Key MON Monitor switch 2 Operation Keys CAM Camera switch DVR Enter the DVR control mode CLR Clear and Cancel MUX Multiplexer mode ENTER Enter key MENU Enter setup menu or PTZ mode SET Set preset position 5 3 Axis PTZ Joystick SHOT Recall preset position LEFT RIGHT Pan movement UP DOWN
24. r operate the device near any high voltage devices or high voltage cable The safety distance should remain at least 50m To achieve best image quality its recommended to use underground cable shielded with steel tube Do not install the cable without any protection In a thunderstorm area or region with high inductive voltage such as high voltage transformer stations it is necessary to use additional lightning proof equipment or lightning rod for protection For outdoor installation lightning proof and grounding of the device should be considered Please refer to the industrial safety regulations of your country Grounding should be considered to eliminate any interference and fulfill the safety requirements Do not connect the ground with short circuited or other high voltage electric networks Make sure that the installation environment meets the requirements of the device such as weight support sufficient room for cords and power supply requirements Installation Connection Schematic The keyboard can be connected to various PTZ cameras DVRs and Matrix devices through the keyboard adaptor All accessories are tested for maximum compatibility and best performance For the first start please ensure your keyboard parameters match those shown on the initial screen ie protocol baud rate ID Doing so will allow you to enter the OSD for further settings ack Wire ay Black al Red
25. rd adaptor and connecting plugs and cable Carefully remove the contents from its packing and set on a firm surface Save the packing in case of future service requirements or transportation needs Dimensions 17 AN TERS pereo ki Q 5 0 Yj ki Q e w UME 0 ZZ 6 e 2 J Precautions For all service or installation needs please refer to qualified service personnel or system installers Do not attempt to disassemble the device To prevent electric shock do not remove screws or cover There are no user serviceable parts inside Contact qualified service personnel for maintenance Handle the device with care Do not strike or shake as this may damage the device It should be protected against extreme pressure vibration and humidity during transportation and storage Damages caused by improper transportation may void the warranty Do not operate the device beyond its specified temperature humidity or power source ratings Do not use the dome camera in an extreme environment where high temperature or high humidity exists Do not install this product in a flammable and explosive environment Make sure that the installation is done according to your local electricity and safety regulations Before installation or maintenance make sure the device is disconnected from the power source Do not use any power source other than 12vdc in order to prevent damages to this device For details please refer
26. red down by unplugging the RJ45 connector from the back of the keyboard Keyboard Setup After entering Admin mode pressIMENUJ To cycle through selections press UP or DOWN to cycle through settings To cycle through options turn the joystick tele zoom or wide zoom to change setting Apply a selection by pressingIENTER Settings SET MUX PROTOCOL Setup the Protocol for Multiplexer Supporting ROBOT default VC SONY BOSCH and PELCO SET MUX PROTOCOL gt ROBOT SET MTX BAUD RATE Setup the Baud Rate for Matrix Supported 1200bps 2400bps 4800bps 9600bps default and 19200bps Press ENTER to save or CLR to exit SET MTX BAUD RAT gt 9600bps 10 DVR SET DVR PROTOCOL Setup the DVR Protocol Supported NVIDO VC DSCP HIK TUMIN MITSU DH and INTLX SET DVR ALL Protocol setting for all DVR ID ALL gt NVIDO gt SET_PROTOCOL gt 01 individual setting for DVR ID 01 01 gt NVIDO SET DVR BAUD RATE Setup the Baud Rate for DVR Supported 1200bps 2400bps 4800bps 9600bps and 19200bps Press ENTER to save or CLR to exit SET DVR l ALL gt 9600bps ALL Protocol setting for all DVR ID N gt SET_BAUDRATE gt 01 individual setting for DVR ID 01 O1 ad SET DVR CHANNEL When multiple DVRs are used the keyboard can map the DVR channel input to certain PTZ IDs Once the DVR s channel is changed on the keyboard the PTZ corresponding to this DVR will be selected automatically DVR ID Monitor ID for outp
27. status and the LCD shows the current selected DVR ID If you have more than one DVR installed and configured you can switch to other ID by pressing NEXT ENTER For returning to PTZ mode press MENU LED for DVR mode enter DVR mode Depending on the DVR Model the function keys may be different Please refer to Function key for NVIDO DVR section for key assignment t Working with DVR Virtual PTZ control in DVR mode In this mode you can control the DVR and PTZ simultaneously by selecting the input on the DVR the PTZ ID assigned to this channel will be automatically selected and ready tor PTZ control DVR and PTZ ID assignment need to be set up prior to operation Please refer to the former chapter Keyboard Setup for details Press DVR key in DVR mode to enter virtual PTZ DVR_ID 01 IN 01 DVR ID 01 ID of the DVR PTZ Cam 001 INE Oli Input of the DVR Indicates the virtual PTZ mode Cam 0001 0 Camera or PTZ ID Switch the camera input channel Press ENTER For returning to the DVR mode press the DVR key again Change the PTZ assignment in DVR mode If you are already in Admin mode you can change the assignment of the PTZ ID to the DVR input directly by pressing the NEXT key Set DVR ID Select the DVR vou need to control or modifv DVRID Output to Matrix ID 01 OUT 0001 IN 01 CAM 001 DVR Input Assign to Channel Camera ID Enter DVR Menu Enter Key 4
28. to move to previous character if needed If you need to delete a character use the SPACE character When finished press IRIS OPEN or use RIGHT to move to last character and then navigate to BACK or EXIT to exit the editing mode Select BACK to exit to SYSTEM SETTING menu 16 INITIAL INFO S N XXXXXXXXXXXXXXX CLINTON V2 42 PROTOCOL CLINTON DOME ADDRESS 001 COMM 9600 N 8 1 DOME LABEL PRESET LABEL ZOOM LABEL ZONE LABEL DIRECTION LABEL TEMPERATURE LABEL TIME LABEL DATE LABEL Il ZONE LABEL inl DIRECTION ZOOM TIME j i ed MOTION AUTO FLIP PROPORTION PAN PARK TIME PARK ACTION POWER UP ACTION FAN ENABLED N N Jl j INITIAL INFO Shows the serial number current firmware version and other settings BACK Move to previous screen EXIT Exit the OSD DISPLAY SETUP Customize the labels shown on the OSD DOME LABEL Shows dome label name on OSD PRESET LABEL Shows the current preset label on OSD see pg 15 Preset ZOOM LABEL Shows magnification setting on OSD ZONE LABEL Shows current zone must first be set up see pg 17 Zones DIRECTION LABEL Shows current direction on OSD Displayed as Pan 0 359 Tilt 0 90 TEMPERATURE LABEL Shows current temperature inside dome on OSD TIME LABEL Shows current time on OSD Displayed as Year Month Day DATE LABEL Shows current date on OSD Displayed as 24 hour clock BACK Move to previous scr
29. to the Specifications section for further details Handle the device during the installation carefully Falls or extreme vibration may cause irreparable damages and void the warranty Do not install or operate the device near any high voltage devices or high voltage cable The safety distance should remain at least 50m This product should be operated indoor only WARNING TO REDUCE THE RISK OF ELECTRIC SHOCK OR FIRE SO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE DO NOT INSERT ANY METALLIC OBJECTS THROUGH THE VENTILATION GRILLS OR OTHER OPENINGS ON THE EQUIPMENT CAUTION This symbol indicates that dangerous voltage RISK OF ELECTRIC SHOCK constituting a risk of electric shock is present DO NOT OPEN within this unit CAUTION MA TO REDUCE THE RISK OF ELECTRIC SHOCK This symbol indicates that there are important DO NOT REMOVE COVER OR BACK operating and maintenance instructions in the NO USER SERVICEABLE PARTS INSIDE literature accompanying this unit REFER SERVICING TO QUALIFIED SERVICE PERSONNEL FCC COMPLIANCE STATEMENT FCC INFORMATION THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS FOR A CLASS A DIGITAL DEVICE PURSUANT TO PART 15 OF THE FCC RULES THESE LIMITS ARE DESIGNED TO PROVIDE REASONABLE PROTECTION AGAINST HARMFUL INTERFERENCE WHEN THE EQUIPMENT IS OPERATED IN A COMMERCIAL ENVIRONMENT THIS EQUIPMENT GENERATES USES AND CAN RADIATE RADIO FREQUENCY ENERGY AND IF NOT INS
30. ut SET DVR ID 01 OUT 0001 gt SET_CHANNEL gt IN 01 CAM 0001 DVR CH ID Camera ID mapped to DVR CH ID Example In DVR mode If DVR2 is selected in the schematic below and PTZ input is changed to 2 the keyboard will automatically recognize the 2nd camera on the selected DVR in this example PTZ ID 6 would be selected as it is the 2nd PTZ camera in sequence on this paticular DVR BNC to DVR RJ45 Communication Cable w Ww ptz pTZIDA pTZIDA pTZIDH tor oard Adap Keynes swith CEPTZKEN w w prz D 5 przI 6 prz1D 7 eTZIDAB BNC to DVR J J DVRIDH 11 CAM SET CAM PROTOCOL Setup the Protocol for CAM Each camera can N A ran send be programmed with a different protocol After setting press ENTER gt SET_PROTOCOL gt 01 gt B02 to save or CLR to exit the setting ALL Protocol setting for all CAMERA ID 01 individual setting for CAMERA ID 01 SET CAM BAUDRATE Setup the Baud Rate for CAM Supported settings 1200bps 2400bps 4800bps 9600bps and 19200bps After L7 TBAUPRATE gt _ o1 _ gt 9600bps setting press ENTER to save or CLR to exit the setting AR T OM Den Keyboard SET KEY ID Setup the ID of the controller from 01 to 63 Input the number by using the digit keys After setting press ENTER to save or CLR to exit the setting an SET KEY LEVEL Setup the control levels of th
Download Pdf Manuals
Related Search