smart led par pro – warm/cold white leds– black user manual
Contents
1. Wluxibe LX112 SMART LED PAR PRO WARM COLD WHITE LEDS BLACK USER MANUAL LX112 USER MANUAL 1 Introduction To all residents of the European Union Important environmental information about this product This symbol on the device or the package indicates that disposal of the device after its lifecycle could harm the environment Do not dispose of the unit or batteries as unsorted municipal waste it should be taken to a specialized company for recycling This device should be returned to your distributor or to a local recycling service Respect the local environmental rules Ee If in doubt contact your local waste disposal authorities Thank you for choosing Luxibel Please read the manual thoroughly before bringing this device into service If the device was damaged in transit don t install or use it and contact your dealer 2 Safety Instructions Be very careful during the installation touching live wires can cause life threatening electroshocks Always disconnect mains power when device not in use or when servicing or maintenance _ gt o activities are performed Handle the power cord by the plug only GO Indoor use only Keep this device away from rain moisture splashing and dripping liquids Ne Never put objects filled with liquids on top of or close to the device Keep this device away from children and unauthorized users Caution device heats up during use Do not stare2. 152 Non linear dimmer 1 153 203 Non linear dimmer 2 204 255 Non linear dimmer 3 10 Cleaning and Maintenance e All screws should be tightened and free of corrosion e The housing the lenses the mounting supports and the installation location e g ceiling Suspension trussing should not be deformed modified or tampered with e g do not drill extra holes in mounting Supports do not change the location of the connections e Mechanically moving parts must not show any signs of wear and tear e The electric power supply cables must not show any damage Have a qualified technician maintain the device e Disconnect the device from the mains prior to maintenance activities Let the device cool down e Wipe the device regularly with a moist lint free cloth Do not use alcohol or solvents e Do not immerse the device in any liquid e There are no user serviceable parts apart from the fuse e Contact your dealer for spare parts if necessary Replacing the Fuse Only replace the fuse by a fuse of the same type and rating 1 Before replacing the fuse unplug the mains lead 2 Unscrew the fuse holder 4 with an appropriate screwdriver 3 Remove the old fuse and install the new fuse in the fuse holder 4 Place the fuse holder back in the housing and tighten it 11 Technical Specifications power supply 240 VAC 50 Hz power consumption 200 W DMX connection 3 pin XLR light source 18 x high power 9 W warm cold white LEDs bea
3. flaws and defective material as from the original date of purchase e Velleman can decide to replace an article with an equivalent article or to refund the retail value totally or partially when the complaint is valid and a free repair or replacement of the article is impossible or if the expenses are out of proportion You will be delivered a replacing article or a refund at the value of 100 of the purchase price in case of a flaw occurred in the first year after the date of purchase and delivery or a replacing article at 50 of the purchase price or a refund at the value of 50 of the retail value in case of a flaw occurred in the second year after the date of purchase and delivery e Not covered by warranty all direct or indirect damage caused after delivery to the article e g by oxidation shocks falls dust dirt humidity and by the article as well as its contents e g data loss compensation for loss of profits consumable goods parts or accessories that are subject to an aging process during normal use such as batteries rechargeable non rechargeable built in or replaceable lamps rubber parts drive belts unlimited list flaws resulting from fire water damage lightning accident natural disaster etc flaws caused deliberately negligently or resulting from improper handling negligent maintenance abusive use or use contrary to the manufacturer s instructions damage caused by a commercia
4. the material and the device itself checked regularly Do not attempt to install the device yourself if you lack these qualifications as improper installation may result in injuries e For truss mounting use an appropriate clamp not incl and fit an M10 bolt through the centre of the folded bracket e Adjust the desired inclination angle via the mounting bracket and tighten the bracket screws e Make sure there is no flammable material within a 0 5 m radius of the device e Have a qualified electrician carry out the electric connection e Connect the device to the mains with the power plug All devices must be powered directly off a grounded switched circuit Do not connect to a dimmer pack e The device has a power output 5 to supply power to another device When connecting several devices in a daisy chain via this output make sure that the total current does not exceed the power line s nominal current Use power cables with an adequate section e The installation has to be approved by an expert before the device is taken into service DMX 512 Connection e When applicable connect an XLR cable to the female XLR output of a controller not incl and the other side to the male XLR input 9 of the device Multiple devices can be linked through serial linking The linking cable should be a dual core screened cable with XLR input and output connectors e Maximum recommended serial data link distance is 500 meters 1640 ft Maximum re
5. to be transported e Keep this manual for future reference 4 Features e PAR projector with high power warm cold white LEDs e extremely slim design e smooth dimming modes e DMX controlled via 2 3 or 7 channels e built in programs e double bracket can be used as a floor spot 5 Overview TEE VIN KN KN 1 display 4 fuse holder 7 passageway for safety cable 2 control buttons 5 power output 8 DMX output 3 power input 6 double bracket o DMX input V 03 26 03 2014 3 Velleman nv LX112 6 Installation Choose a suitable mounting spot Mount the device in the desired angle using the included bracket Connect the power cord to the mains Disconnect after use Mounting the Device e Have the device installed by a qualified person respecting EN 60598 2 17 and all other applicable norms e The carrying construction must be able to support 10 times the weight of the device for 1 hour without deforming e The installation must always be secured with a secondary attachment e g a safety cable e Never stand directly below the device when it is being mounted removed or serviced Have a qualified technician check the device once a year and once before you bring it into service e Install the device in a location with few passers by that is inaccessible to unauthorised persons e Overhead mounting requires extensive experience calculating workload limits determining the installation material to be used Have
6. 2 Press MENU until lt P gt is displayed and press ENTER 3 Use UP and DOWN to select a built in program P 1 to P 5 and press ENTER to confirm The current program speed appears 4 Use UP and DOWN to set the speed from slow 0 to fast 100 and press ENTER to confirm 5 Press MENU to quit Dimmer Modes You can choose a dimmer mode to control the colour transitions in the automatic programs The dimmer mode has no effect on static colours To set the dimmer mode proceed as follows 1 Press MENU until lt dIM gt is displayed and press ENTER 2 Use UP and DOWN to select the desired setting o lt OFF gt dimmer off for abrupt colour transitions Note In master slave mode set the dimmer to lt OFF gt on the slave device if you want the slave device to use the same dimmer mode as the master device o lt DIM1 gt lt DIM3 gt dimming modes 1 to 3 for smooth colour transitions 3 Press ENTER to confirm After changing the dimmer mode you have to reactivate the automatic program as follows 4 Press MENU until lt P gt is displayed and press ENTER Use UP and DOWN to select the desired program and press ENTER 6 Press MENU to quit y V 03 26 03 2014 5 Velleman nv LX112 8 Master Slave Mode The master slave mode allows connecting several devices to a single master device All slave devices will then work synchronously with the master device You need to set one device to master mode and all o
7. commended number of devices on a serial data link is 32 devices e A DMX terminator is recommended for installations where the DMX cable has to run a long distance or is in an electrically noisy environment e g discos The terminator prevents corruption of the digital control Signal by electrical noise The DMX terminator is simply an XLR plug with a 120 Q resistor between pins 2 and 3 which is then plugged into the XLR output socket 8 of the last device in the chain 7 Operation The device can be used in the following modes e stand alone mode e master slave e with a DMX512 controller 7 1 Control Panel Navigation Access the control panel functions using the four panel buttons 2 located directly underneath the display 1 From left to right Button Function MENU used to access the menu or to return to a previous menu option UP scrolls through the menu options in ascending order DOWN scrolls through the menu options in descending order ENTER used to select and store the current menu or option within the menu V 03 26 03 2014 4 Velleman nv LX112 7 2 Stand Alone Mode In stand alone mode the device runs one of the built in programs You can also select one of the built in static white colours various colour temperatures or define your own custom white colour You can use a strobe effect with the custom white colour Note Make sure to unplug any connection from the DMX input of the device if you want to use i
8. directly at the light source as this may cause e epileptic seizure in sensitive people e temporarily loss of sight flash blindness e permanent irreversible eye damage There are no user serviceable parts inside the device Refer to an authorized dealer for service and or spare parts gt gt I gt gt e This device falls under protection class I It is therefore essential that the device be earthed Have a qualified person carry out the electric connection e Make sure that the available voltage does not exceed the voltage stated in the specifications of this manual e Do not crimp the power cord and protect it against damage Have an authorised dealer replace it if necessary e Use an appropriate safety cable to fix the device e g VDLSC7N or VDLSC8N e Install the device at a minimal distance of 0 5 m from flammable and explosive objects or substances e Respect a minimum distance of 0 5 m between the device s light output and any illuminated surface e The maximum ambient temperature is 40 C Do not operate the device at higher temperatures 3 General Guidelines Refer to the Velleman Service and Quality Warranty on the last pages of this manual are clear at all times For sufficient air circulation leave at least 1 2 5 cm in front of the Keep this device away from dust and extreme temperatures Make sure the ventilation openings openings Protect this device from shocks and abuse Avoid brute force
9. l professional or collective use of the article the warranty validity will be reduced to six 6 months when the article is used professionally damage resulting from an inappropriate packing and shipping of the article all damage caused by modification repair or alteration performed by a third party without written permission by Velleman e Articles to be repaired must be delivered to your Velleman dealer solidly packed preferably in the original packaging and be completed with the original receipt of purchase and a clear flaw description e Hint In order to save on cost and time please reread the manual and check if the flaw is caused by obvious causes prior to presenting the article for repair Note that returning a non defective article can also involve handling costs e Repairs occurring after warranty expiration are subject to shipping costs e The above conditions are without prejudice to all commercial warranties The above enumeration is subject to modification according to the article see article s manual Made in PRC Imported by Velleman nv Legen Heirweg 33 9890 Gavere Belgium www velleman eu
10. ll have to set the start address of the first unit to 1 CH1 3 the second to 4 1 3 CH4 6 the third to 7 4 3 CH7 9 and so on The highest start address is 510 e Incase of the 7 channel mode you will have to set the start address of the first unit to 1 CH1 7 the second to 8 1 7 CH8 14 the third to 15 8 7 CH15 21 and so on The highest start address is 506 To set the device to work with a DMX controller 1 Press MENU until lt PERS gt is displayed and press ENTER 2 Use UP and DOWN to select the 2 3 or 7 channel DMX mode 2 CH 3 CH or 7 CH and press ENTER 3 Press MENU until lt AddR gt is displayed and press ENTER 4 Use UP and DOWN to set the DMX starting address di d512 and press ENTER DMX Channel Values 2 channel mode Channel From To Description 1 0 255 Warm white 0 100 2 0 255 Cold white 0 100 3 channel mode Channel From To Description 1 0 255 Master dimmer 2 0 255 Warm white 0 100 3 0 255 Cold white 0 100 7 channel mode Channel From To Description 1 0 255 Master dimmer 2 0 255 Warm white 0 100 2 0 255 Cold white 0 100 j 0 9 Off 10 255 Strobe slow to fast V 03 26 03 2014 6 Velleman nv LX112 Channel From To Description 0 51 Off 52 101 Auto program 1 102 152 Auto program 2 3 153 203 Auto program 3 204 254 Auto program 4 255 255 Auto program 5 6 0 255 Speed slow to fast if channel 5 52 255 0 51 Default dimmer speed 52 101 Linear dimmer 7 102
11. m angle 25 dimensions 295 x 255 x 100 mm weight 5 kg Use this device with original accessories only Velleman nv cannot be held responsible in the event of damage or injury resulting from incorrect use of this device For more info concerning this product and the latest version of this manual please visit our website www luxibel com The information in this manual is subject to change without prior notice COPYRIGHT NOTICE The copyright to this manual is owned by Velleman nv All worldwide rights reserved No part of this manual may be copied reproduced translated or reduced to any electronic medium or otherwise without the prior written consent of the copyright holder V 03 26 03 2014 7 Velleman nv Velleman Service and Quality Warranty Since its foundation in 1972 Velleman acquired extensive experience in the electronics world and currently distributes its products in over 85 countries All our products fulfil strict quality requirements and legal stipulations in the EU In order to ensure the quality our products regularly go through an extra quality check both by an internal quality department and by specialized external organisations If all precautionary measures notwithstanding problems should occur please make appeal to our warranty see guarantee conditions General Warranty Conditions Concerning Consumer Products for EU e All consumer products are subject to a 24 month warranty on production
12. t in stand alone mode A device in stand alone mode may transmit DMX signals that could interfere with the DMX signals from the controller Stand Alone Mode with Built in Static Colour To use one of the built in static colours 1 Unplug any connection from the DMX input 9 of the device Press MENU until lt C gt is displayed and press ENTER Use UP and DOWN to select a pre set colour C 01 to C 03 Press ENTER to confirm Press MENU to quit rae sae Xa Stand Alone Mode with Custom Static Colour You can create a custom colour by adjusting the intensity of the cold white C and warm white W LEDs To use a custom static colour 1 Unplug any connection from the DMX input 9 of the device 2 Press MENU until lt U gt is displayed and press ENTER The last set value appears for example lt W215 gt warm white LEDs intensity value 215 3 Use UP and DOWN to set the intensity 0 255 and press ENTER The cold white LED value appears for example lt C000 gt cold white LEDs intensity value 000 off 4 Use UP and DOWN to set the intensity 0 255 and press ENTER The strobe speed value appears 5 Use UP and DOWN to set the strobe speed from slow to fast 0 20 Set to 0 to switch off the strobe 6 Press ENTER to confirm 7 Press MENU to quit Stand Alone Mode with Built in Program To set the device to stand alone mode with a built in program 1 Unplug any connection from the DMX input 9 of the device
13. ther devices to slave mode 1 Connect all devices in series with DMX cables 2 The first unit in the chain functions as the master device Set up the unit as described in Stand Alone Mode 3 On each slave device press MENU until lt AddR gt is displayed and press ENTER 4 Use UP and DOWN to set the DMX starting address to lt d1 gt and press ENTER 5 Repeat for each slave device 9 DMX Mode This mode allows you to control the device by any universal DMX controller e All DMX controlled devices need a digital start address so that the correct device responds to the signals This digital start address is the channel number from which the device starts to listen to the DMX controller The same starting address can be used for a whole group of devices or an individual address can be set for every device e When all devices have the same address all the units will listen to the control signal on one particular channel In other words changing the settings of one channel will affect all devices simultaneously If you set individual addresses each device will listen to a separate channel number Changing the settings of one channel will only affect the device in question e Incase of the 2 channel mode you will have to set the start address of the first unit to 1 CH1 2 the second to 3 1 2 CH3 4 the third to 5 3 2 CH5 6 and so on The highest start address is 511 e Incase of the 3 channel mode you wi
14. when operating the device e Familiarise yourself with the functions of the device before actually using it Do not allow operation by unqualified people Any damage that may occur will most probably be due to unprofessional use of the device e All modifications of the device are forbidden for safety reasons Damage caused by user modifications to the device is not covered by the warranty V 03 26 03 2014 2 Velleman nv LX112 e Only use the device for its intended purpose All other uses may lead to short circuits burns electroshocks lamp explosion crash etc Using the device in an unauthorised way will void the warranty e Damage caused by disregard of certain guidelines in this manual is not covered by the warranty and the dealer will not accept responsibility for any ensuing defects or problems e Mechanical wear and LEDs are not covered by warranty e A qualified technician should install and service this device e Do not switch the device on immediately after it has been exposed to changes in temperature Protect the device against damage by leaving it switched off until it has reached room temperature e This device is designed for professional use on stage in discos theatres etc The device should only be used indoors with an alternating current of 240 VAC 50 Hz e Lighting effects are not designed for permanent operation regular operation breaks will prolong their lives e Use the original packaging if the device is
Download Pdf Manuals
Related Search