Home

GsmAlarm

1. 2A e switch on the power source and wait till SIGNAL indicator is on Output active siren is on Connected to e switch off power source GND e take off RESET jumper Output non active siren is off Open contact OUTPUT C1 Maximum current 200 mA Output active siren is on Connected to GND Output non active siren is off Open contact INPUTS Z1 Z5 Load resistance 2 2 KO 10 Upper triggering limit 35V Lower triggering limit 1V ELEKTRONINES TECHNOLOGIJOS 2006 http www eltech It
2. indicator blinks a little bit slower about twice a second Blinks very rapidly 10 20 times a second SMS instruction receipt confirmation ALARM alarm mode indicator Blinks at a permament rate system is in alarm state call is made or SMS sent Blinks twice every 2 3 seconds SMS center SMSNR or ALRNR1 number has not been programmed In order GsmAlarm could send SMS and make calls these numbers need to be programmed GETTING READY FOR WORK Before switching the power source on GsmAlarm 400 inputs Z1 Z5 need to be loaded with 2 2k resistors switch S1 must be OFF Insert SIM card into mobile phone with its PIN code request OFF connect phone to GsmAlarm 400 After switching power source on wait for SIGNAL indicator starts blinking periodically and MODE LED1 indicator is on continuously If SIGNAL indicator is on continuously check if the SIM card PIN code request has been switched off Slowly blinking ALARM indicator shows that SMS center SMSNR or and ALRNR1 number has not been programmed Program them in accordance with paragraph 5 1 If both numbers have been programmed ALARM indicator is OFF ALRNRI number needs to be programmed This number is used by GsmAlarm to send SMSs at main power failure or if a call from unknown number is received After the system is switched on with S1 switch the control call is addressed to the first user The rest four user numbers are not required Sequence is also not required e g yo
3. no SMS Second digit 1 in this case is a number of calls in the alarm case Possible values are 1 2 or 3 In order to change only one of these parameters SMS must include also the other parameter i e number after C must have two digits T40 delay time after system activation In this case zones are not checked 40 seconds after switching on Possible values are 00 99 The delay time is ignored when zone is in a 24 hour mode S01 siren on time in alarm case in minutes Possible values are 01 99 In the given example the following parameters are changed zone 1 operation mode delay time and name zone 2 only operation mode M20 zone 3 only name zone 4 delay time 10 seconds SMS sending condition after stranger s call and number of calls in alarm case 01 delay time after switching on 40 seconds and siren on time 1 minute IMPORTANT a no space character must be inserted after the colon b if not only name is changed in this case Al and Z4 space character must be inserted between the two digit number and name c comma must be inserted after the last changed zone parameter ON OFF zone is used for alarm arming disarming When zone is non active the system is off no zone sensor signals are responded to except when zone is in 24 hour operation mode When ON OFF is active short or broken circuit system is in the armed mode After the protected zone is activated the alarm responds in accordance
4. order to do this send GsmAlarm the following SMS AAAAAAAA SPARAM Send this SMS from any GSM subscriber not necessarily from the user The only condition is that you must know the correct password SMS central number must have been programmed also see par 5 1 otherwise GsmAlarm is unable to send a SMS GsmAlarm 400 sends SMS to the sender s address showing all zone parameters and names SMS with manufacturer s parameters looks like the following Z1 M70T20 Door Z2 M70T20 Windows Z3 M70T00 Movement Z4 M71T00 Fire Z5 M02T00 ON OFF PR C12T20S02 Z1 zone number M40 zone operation mode parameter M see fig 2 T20 zone delay time after triggering seconds Door zone name showed in the SMS after triggering PR C12T20S02 PR system parameters C12 the first digit 1 shows whether SMS is to be sent if GsmAlarm is called from unknown number In this case SMS will be sent The second digit 2 shows number of the calls to the user users in case of alarm In this case system will call twice on condition that X value equals 2 4 or 7 in fig 2 T20 shows how many seconds the system will wait before checking the zones after arming This time is the same for all the zones S02 siren ON time in alarm case minutes Alarm state after zone activation M Zone mode xX Y Only information zone 0 0 Zone with delay Only siren is on 1 1 24 hour zone siren is on continuous
5. with the table given in fig 2 GSM alarm system GsmAlarm 400 401 mini GSM alarm system GsmAlarm 400 401 mini 5 5 MANUFACTURER S DEFAULT PARAMETERS 6 TECHNICAL CHARACTERISTICS Password AAAAAAAA POWER SUPPLY There are neither SMS center nor user numbers programmed AC voltage in the secondary winding of power transformer input 16 18V AC Z1 zone with delay delay time is 20 seconds M70T20 name Door Minimum current of the secondary winding of power transformer 600 mA Z2 zone with delay delay time is 0 seconds M70T00 name Windows Reserve battery type PB acid Z3 zone with delay delay time is 0 seconds M70T00 name Movement Reserve battery operation voltage 12V Z4 24 hour zone siren is on with breaks M72T00 name Fire Reserve battery maximum capacity 7 Ah Z5 ON OFF zone M03T00 Reserve battery charging current 300 500 mA PR C12T20S02 in case stranger s call incomes user is sent a SMS number of the calls in alarm AUXILIARY DEVICE FEEDING OUTPUT AUX case is 2 C12 delay after switching on is 20 seconds T20 siren on time is 2 minutes S02 Maximum current 1A Short circuit protection triggering current 1 35 A In order to reset all the system parameters into the default ones do the following SIREN OUTPUT BELL switch off both power source and reserve battery insert RESET jumper Maximum current
6. GSM alarm system GsmAlarm 400 401 mini 1 GENERAL DESCRIPTION GsmAlarm 400 is a 4 zone GSM alarm system and and may be customized for premises protection GsmAlarm 400NK is operable along with NOKIA 5110 or NOKIA 6110 cellular phone units GsmAlarm 400SI is operable along with SIEMENS C35i M35i S35 ME45 M50 MT50 cellular phone units GsmAlarm 400ER is operable along with ERICSSON T10s T18s T28s cellular phone units GsmAlarm 400 has an integrated AC DC converter it may charge a standard battery with capacity 7Ah In the case of alarm the unit starts a siren and may call or send SMSs to five users The SMS shows the user the name of the violated zone as well as the number of times the sensor was triggered System activation deactivation is available remotely and is cost free The system is activated with a brief call to the GsmAlarm phone In order to deactivate the system call and wait for some time after 3 4 tones the system is deactivated GsmAlarm is controllable from the user s phone only If unknown number is calling the call is immediately interrupted and the user gets a SMS showing the caller s number SMS also shows power failure of the main source 220V In this case the system is powered from the reserve battery SMS is also sent after the power supply is restored The system may be programmed remotely by sending to GsmAlarm a SMS with relevant contents and password USER S MANUAL User can activate deacti
7. contact is to be connected to positive terminal of reserve battery CONTACTS AC The AC input is used to connect secondary winding of power supply transformer 16 18V AC LED INDICATORS The LEDs fig 1 enable instant adjustment of the system at installation and fault localization SIGNAL GSM module operation mode indication Possible states Off system is off there is no power supply Continuously On GSM module is effective but there is no network registration Possible causes SIM card PIN code request is not off there is no antenna connected or communication quality is poor Blinks every 2 3 seconds GSM module is active communication is present and all is OK Z1 ZA zone status indicators Off zone is not triggered Continuously On zone is triggered or load resistor is broken GSM alarm system GsmAlarm 400 401 mini MODE and LED1 system mode indicators Off system is off Possible causes there is no supply voltage or some damage is present Continuously On system is on but it is disarmed Blinks every 2 3 seconds System is operating in armed mode there is no alarm Blinks twice every 2 3seconds System is operating in armed mode but mobile communication devices are out of operation If zone is triggered in this state only siren will be on Blinks rapidly several times per second System is in alarm state siren is active call is made or SMS is sent If SMS is sent
8. der to delete unnecessary number send the following SMS AAAAAAAA ALRNR2 N Number ALRNR2 is deleted user gets a SMS with programmed numbers In order to alter a number no additional instruction to delete the old number is necessary SMS PASSWORD CHANGE In order to change manufacturer s SMS password send GsmAlarm the following SMS AAAAAAAA PASSW ABCDefgh AAAAAAAA is the old password PASSW password changing instruction ABCDefgh new SMS password It must contain 8 characters If programming instruction is performed correctly user gets a SMS with newly programmed password GSM alarm system GsmAlarm 400 401 mini 5 3 INFORMATION SMSs In order to get a SMS about state of the system and protected zones send the following SMS AAAAAAAA ZONES In order to get a SMS with programmed numbers and password send GsmAlarm the following SMS AAAAAAAA NRINFO In order to get a SMS with information about GSM signal strength and power supply voltage send GsmAlarm the following SMS AAAAAAAA PRINFO In order to get a SMS with programmed parameters and names of protected zones send GsmAlarm the following SMS AAAAAAAA SPARAM GSM alarm system GsmAlarm 400 401 mini 5 4 PROGRAMMING OF SYSTEM PARAMETERS AND ZONE NAMES All GsmAlarm 400 zone input operation modes delay times and names may be programmed with a single SMS First of all it is advisable to get a SMS with already programmed parameters In
9. e system gets a brief confirming call In order to check operation of the alarm call briefly the GsmAlarm number If it is operative the calling user gets a short confirming call In the alarm case depending on the programmed parameters of the triggered zone all the users in a sequence are called or sent SMSs showing the triggered zone name and number of triggers User may pick up and listen what is going on in the premises or cancel the call and wait for GSM alarm system GsmAlarm 400 401 mini SMS After at least one user picks up the system stops calling and sending SMSs In order to get a message showing state of all the zones send the system a SMS with the password and word ZONES Then GsmAlarm sends a SMS showing state of the controlled zones to that user In order to get information about power source and communication quality send a message containing password and word PRINFO INSTALLATION Fig 1 GsmAlarm connection diagram 3 1 CONTROLLED ZONE INPUTS Z1 Z5 Controlled zone inputs Z1 Z4 are used to connect sensors All the inputs are analogue i e micro controller is measuring voltage in each input thus in the case of short circuit or brake of the controlled circuit the system enters the alarm mode siren is on user is called or sent a SMS Each zone input must be loaded with 2 2k resistors connecting them to the sensors located farthest The connection diagram shows two sens
10. ly Only calling 2 2 24 hour zone siren is on with interruptions fire sensor Only SMS is sent 3 3 ON OFF zone Call is made and SMS is sent 4 Siren is on call is made 5 Siren is on SMS is sent 6 Siren is on call is made SMS is sent 7 Fig 2 Zone operation mode parameter M GSM alarm system GsmAlarm 400 401 mini In order to change parameters or names send GsmAlarm a special SMS containing the parameters to be changed e g AAAAAAAA Z1 M10T20 Namel Z2 M20 Z3 name3 Z4 T10 Name4 PR C01T40S01 AAAAAAAA 8 character password Z1 parameter change instruction for relevant zone colon is obligatory M10 zone operation mode instruction 10 2 digit number XY X 1 Y 0 specifying zone mode see fig 2 T20 zone delay time in seconds in this case it is 20 seconds Possible values 00 99 Number must have 2 digits E g for the delay time was 5 seconds state TOS not T5 The delay time is ignored when zone is in a 24 hour mode Namel name of zone 1 It is 16 digits long at a maximum PR C01T40S01 system parameter changing instruction colon is obligatory C01 the first digit 0 in this case shows system response to stranger s call Possible values are 0 or 1 If it is 1 after a stranger calls the system the system cancels the call and sends the first user a SMS showing caller s number If it is 0 after a stranger calls the system the system cancels the call and sends
11. or connection options D1 and D2 are standard sensors used in the protection systems with closed contacts at rest e g magnetic contacts of windows doors When the sensor is triggered the contacts become open and the system enters danger mode D3 and D4 are standard sensors used in the protection systems with open contacts at rest e g movement or fire sensors When the sensor is triggered the contacts close and the system GSM alarm system GsmAlarm 400 401 mini 3 2 3 3 3 4 3 5 3 6 3 7 enters alarm mode after the delay period audio siren is on and the system calls or sends the user SMS Input Z5 S1 switch is used to activate deactivate the system If S1 contacts are open the system is off no zones are checked except when zone operates in 24 hour mode If contacts of S1 are closed the system is active all the zones are checked in the case of alarm siren is on and the system calls or sends the user SMS OUTPUT BELL The BELL output is used to connect audio siren Commutated current may reach 2A When active BELL is connected to GND ground wire OUTPUT C1 The programmable output C1 may be used to connect external system mode indicator LED1 Maximum commutated current in this output is 200mA OUTPUT AUX The AUX output is used to supply power to external devices and is short circuit protected This output has voltage 12 13 7V Maximum load current is 1A CONTACT BATT The BATT
12. u can program ALRNRI ALRNR4 and ALRNRS If needed the zone and system parameters shall be programmed see par 5 4 Upon completion of programming it is recommended to change SMS password see par 5 2 After you connect reserve battery and check for Z1 Z4 control LEDs are off activate the system with S1 wait for confirming call at ALRNR1 number To check if the system sends SMSs switch off the main power source After 20 seconds user ALRNR1 is sent a SMS If not check SMS central number for correct programming Note In case of main power failure or restoration SMS is sent only in armed mode and only to ALRNR1 user GSM alarm system GsmAlarm 400 401 mini 5 5 1 5 2 PROGRAMMING SMS CENTER AND USER NUMBER PROGRAMMING In order to program SMS central and user numbers sent to GsmAlarm 400 SMS with the following contents AAAAAAAA SMSNR 0123456789 ALRNR1 0123456789 ALRNR2 0123456789 ALRNR3 0123456789 ALRNR4 0123456789 ALRNR5 0123456789 AAAAAAAA eight character SMS password obligatory in the beginning of each SMS Manufacturer has programmed the following password AAAAAAAA User may change the password as he wants see par 5 2 SMSNR SMS center number ALRNRI1 ALRNRS user numbers GsmAlarm 400 may be called exclusively from these numbers All the other calls are ignored and immediately cancelled If programming is performed correctly user gets a SMS with newly programmed numbers In or
13. vate the system in the following two ways 1 Using the ON OFF switch In this case after the switch is switched ON the activation delay time is started to count down MODE indicator is blinking If after expiration of the given time neither zone is activated the system enters armed mode user ALRNR1 gets a short confirming call and MODE indicator starts blinking at a reduced frequency Confirming call needs no cancellation it is cancelled automatically If after the delay period no confirming call is received and MODE indicator is continuously on it means that some of the zones is active open window door etc Alarm may be deactivated by switching the switch OFF If the system is deactivated and the 24 hour zone is triggered the siren and the call may be cancelled by switching the switch ON and immediately OFF 2 Remotely using own cellular phone In order to activate the system user must call the GsmAlarm number and after hearing the first tone cancel the call No activation delay time is counted in this case after the system is activated the user gets a short confirming call Confirming call needs no cancellation it is cancelled automatically The alarm may be deactivated by calling the GsmAlarm number and waiting for the system cancels the call 3 4 tones If after remote deactivation neither of the sensors are triggered within one minute the system automatically enters armed mode and the user who deactivated th

GsmAlarm

Contents

Download Pdf Manuals

Related Search

Related Contents