inLab Partial Framework Software Version 1.0.0
Contents
1. Click to set a new profile disk Hold down the left mouse button and drag the mouse up or down to adjust the thickness of the profile Hold down the right mouse button and drag the mouse up or down to adjust the width of the profile 65 38 222 D3534 D3534 208 01 01 02 01 2015 Sirona Dental Systems GmbH 7 Editing orders Operator s Manual inLab Partial Framework 7 5 DESIGN phase Reversing the clamp profile gt Click on the Flip Direction button in the side palette The clamp profile is reversed Adding a clamp gt Select Add Clasp to set an additional clamp Mu Tip You can also draw a clamp in several segments around the tooth To do this start on one side of the tooth then guide the clamp around the tooth as far as you like and close it with a double click Then select Add zz Clasp start from the other side and guide this clamp to the end point of the first one Both elements are fused into one clamp in phase FINALIZE Clamp ladder 1 Select C asp Bar from the side palette or the tool wheel 2 Select the desired diameter of the clamp ladder using the Diameter slide controller in the side palette 3 Select the desired relief gap using the nc ination slide controller in the side palette 4 You must also observe the notes in the section Linear elements gt 17 Changing the clamp ladder 1 Click on the Connector Edit Lines button 2 Click on the Drag Line button 3 Sel2. 16 D3534 208 01 01 02 01 2015 Sirona Dental Systems GmbH Operator s Manual inLab Partial Framework 6 Construction elements 6 1 Linear elements Construction elements Linear elements Linear elements are created using an open line on the jaw 1 Begin the line with a double click 2 Insert additional points in between by clicking on the left mouse button 3 Setthe line end by double clicking After entry the element is created with standard profile settings 4 You have the option of editing both the line itself and also the profile along the line Here you can switch between the various editing modes using the space bar The following elements are designed in the inLab Partial Framework software as linear elements Clamp There are different types for selection e Premolar e Molar e Ring Clamp ladder Closing edge 65 38 222 D3534 D3534 208 01 01 02 01 2015 17 6 Construction elements Sirona Dental Systems GmbH 6 2 Laminar elements Operator s Manual inLab Partial Framework Laminar elements Laminar elements are defined by a closed line 1 Begin the line with a double click 2 Insert additional points in between by clicking on the left mouse button 3 Setthe line end by double clicking on the starting point The laminar element is calculated within the line 4 You have the option of editing both the line itself and also the profile along the line Here you can switch
3. Click on the Drag L ne button 3 Selectthe active area the yellow part of the line by holding down the right mouse button and dragging the mouse up and down 4 Dragthe line by moving the mouse to the desired point 1 Click on the Connector Edit Lines button 2 Click on the Edit Line button A 32 Redraw the lines at the desired points by starting with a double click setting points with left clicks and ending the line by double clicking 65 38 222 D3534 D3534 208 01 01 02 01 2015 Sirona Dental Systems GmbH 7 Editing orders Operator s Manual inLab Partial Framework 7 5 DESIGN phase Adjusting the closing edge V You have selected a closing edge 1 Click on Edit Profile in the side palette R 2 Move the mouse over the element A new profile disk is displayed 3 Click to set a new profile disk 4 Hold down the left mouse button and drag the mouse up or down to adjust the thickness of the profile 5 Hold down the right mouse button and drag the mouse up or down to adjust the width of the profile Adding a closing edge 2 Select Add Finishing Line to set an additional closing edge IMPORTANT The closing edge can be constructed on retention plates base plates connectors or lingual bows Retention plate 1 Select Grid from the side palette or the tool wheel 2 Select the desired retention plate thickness using the Thickness a slide controller in the side palette 3
4. Operator s Manual inLab Partial Framework The Set nsertion Axis tool allows you to set the axis for blocking out the jaw The rear section depth can be assessed using the color gradient The color changes every 0 1 mm A block out angle can be set as an additional parameter for blocking out the jaw In order to modify the angle hold down the left mouse button and drag the mouse up or down 4 5 Shaping the wax Wachs forme You can process the blocking out wax using the Form tool You can remove add or smoothen the wax 65 38 222 D3534 28 D3534 208 01 01 02 01 2015 Sirona Dental Systems GmbH 7 Editing orders Operator s Manual inLab Partial Framework 7 5 DESIGN phase 4 4 Biogeneric Copy If a biogeneric copy has been scanned into the inLab SW software this is loaded into the inLab Partial Framework software together with the model Adding a biogeneric copy retrospectively X The case must be opened in the inLab Partial Framework software 1 Likewise open the case in the inLab SW software and go to phase SCAN Add the image catalog BioCopy Upper or BioCopy Lower and scan the model including the wax exhibit 7 2 Allow the model to be calculated 3 Restart the inLab Partial Framework software after the model calculation 4 The Auto Align tool is provided to correctly display the biogeneric copy on the active jaw 5 Ifa biogeneric copy has been imported with the inLab Partial Framewo
5. by step The double arrow keys can be used to switch between steps and phases 13 4 User interface Sirona Dental Systems GmbH 4 5 System menu Operator s Manual inLab Partial Framework System menu In the system menu you can e Opena case e Save a case e Save a case under a different name e Open license manager e Configure software e Change window mode e Retrieve software information e Close the software Opening system menu 2 Move the mouse cursor to the top of the window or gt Click the start window button The system menu is displayed Closing system menu gt Click the start window button or gt Click into the main window with the left mouse button The system menu is closed Save case In this dialog you can save the actual case gt Select Save Case in the system menu The current processing status of the case is saved 65 38 222 D3534 14 D3534 208 01 01 02 01 2015 Sirona Dental Systems GmbH 4 User interface Operator s Manual inLab Partial Framework 4 5 System menu Save the case under a different name This dialog allows you to save the current case under a new name or assign it to a different patient 1 Select Save Case As in the system menu 2 Select the desired save location and enter a file name License manager on the USB license stick To do this start the license manager via the system menu and follow the instructions on the scre
6. measurement direction 1 Click on the Analyzing Tools button 2 Click on the Check Thickness button The color scheme is displayed on the model casting The material thickness can be read using the legend 25 7 Editing orders Sirona Dental Systems GmbH 7 2 Scanning the jaw in the inLab SW software Operator s Manual inLab Partial Framework Scanning the jaw in the inLab SW software 1 Scanthe model with the inEos X5 in the inLab SW software and have the model calculated see also the inLab SW user manual 2 A Biocopy Model through the BioCopy image fields can also be scanned which can then later be used in the inLab Partial Framework software for the construction This can still be aligned in the MODEL phase The alignment is then adopted directly into the inLab Partial Framework software Starting inLab Partial Framework X The inLab SW software is installed You will find the start icon on the desktop X The USB license stick is connected with a valid current license X They are located in phase VODEL in the inLab SW software and a 3D model is already calculated 1 Open the software inLab SW 2 Click the Run Application button in the system menu inLab SW Run Application 3 Then click on the Partial Framework button The software is started Alternative start options X The inLab Partial Framework software is installed You will find the start icon of the inLab Partial Frame
7. on the Add Material button 2 By holding down the right mouse button and dragging the mouse up and down you can adjust the size of the ball 3 Add material by double clicking Adding a grain You can add a grain to the model casting using this tool in phase FINALIZE zd 1 Click on the Surface pattern button 2 Click with the mouse cursor on the area you wish to add a grain 3 Press and hold the left mouse button and smoothen the surface location by moving the mouse The area becomes orange colored 4 Click on Apply to add the grain Modifying the size A You can use the Size button to modify the size of the area affected The H area affected is shown as an orange colored area The size of the area affected can be modified for each shaping tool 1 Click on the Surface pattern button 2 Click the Size button and press and hold the mouse button 3 Drag the mouse cursor up or down The size of the orange area is enlarged or reduced The size is shown on the restoration Tip You can also change the size by clicking on the restoration with the right mouse button and while holding the right mouse button down dragging the mouse up or down 65 38 222 D3534 D3534 208 01 01 02 01 2015 23 7 Editing orders Sirona Dental Systems GmbH 7 1 Tools and functions of the page palette Operator s Manual inLab Partial Framework Adding a support pipe For certain production processes it is necessary
8. other protected material Anyone who copies this software to any medium for any purpose other than his own personal use without the written permission of Sirona Dental Systems will be liable to prosecution Microsoft and Windows 7 are registered trademarks Windows is a trademark of Microsoft Corporation All other trademarks are the property of their respective holders Notes on 3rd party code libraries must be stored in license pdf in the installation directory 2 General data Sirona Dental Systems GmbH Operator s Manual inLab Partial Framework 2 1 General safety information General data Please read this document completely and follow the instructions exactly You should always keep it within reach Original language of the present document German General safety information Only use original software Only use original software or software which has been released by Sirona To produce restorations and equipment manipulated or non released software components must not be used Software and software components must not be installed using incorrect data Please check that each installed component has been granted approval in its country Contact your dealer for more information Restoration to be checked by trained personnel Each restoration which is performed with this software must be checked for suitability by a trained person e g dental technician or dentist For the USA only CAUTION Ac
9. 1 22 22 23 23 24 24 25 25 25 26 26 2 2 2 28 29 29 30 31 32 33 34 35 36 36 3 38 38 39 39 40 Table of contents Sirona Dental Systems GmbH Operator s Manual inLab Partial Framework 720 3 JAddihg SuDDOLUDIDOS caca ain dita leue a i setatis 40 7 6 4 Exporting the model Casting ccccccccccseeceeeeeeeeeeeeeeeeeeeseeeseeesaes 40 8 Tps and TICKS mierea aren aren ert err ent ere Terre er 41 8 1 non 9 0 9161 0 KEYS ei Expire eese eee ee 41 43 65 38 222 D3534 D3534 208 01 01 02 01 2015 Copyright Trademarks 65 38 222 D3534 D3534 208 01 01 02 01 2015 Introduction Dear Customer Thank you for purchasing your inLab Partial Framework software from Sirona When combined with the scanner inEos X5 this software enables you to record models and construct model castings Improper use and handling can create hazards and cause damage Therefore please read and follow this manual carefully You should always keep it within reach Train using practice models to command the software safely To prevent personal injury or material damage it is important to observe all safety information Your inLab team Copyright and trademark Sirona Dental Systems GmbH All rights reserved The information contained in this manual may be changed without notice The software and all related documentation are protected by copyright You must therefore handle it in the same way as any
10. 5 38 222 D3534 D3534 208 01 01 02 01 2015 T Conventions Clicking A single click down and releasing of the left mouse button Double clicking Clicking and releasing of the left mouse button twice in quick succession Moving the mouse Moving the mouse in the described direction in one direction Seizing a point Press the left mouse button and hold it down Cir N On the keyboard Press the Ctrl and N keys simultaneously Drag amp drop Drag amp drop Press and hold an element e g pictograph and drop onto new potential destination Formats of the manual You can access the manual via the Help button or by pressing F1 The pdf format user manual can be found on the supplied software DVD or on the Internet http www sirona com manuals This format is page oriented and is well suited for printing out the desired pages File format Depending on the status of processing an order consists of calculated virtual models and a model casting The software uses its own file format pf to export an order This format contains all of the order data PF files can be opened with other inLab Partial Framework installations Under certain circumstances older software versions cannot open data exports from a more recent version 65 38 222 D3534 D3534 208 01 01 02 01 2015 Sirona Dental Systems GmbH 3 Getting started Operator s Manual inLab Partial Framework 3 1 Installing the software Getting started I
11. 8 222 D3534 40 D3534 208 01 01 02 01 2015 Tips and Tricks Shortcut keys Buoni 1 In the phase PREPARE in step A gn Starts the Form tool Model or Check Blockout if blockout calculated FOU Lj In the phase DES GN Starts the tool for inserting a retention plate HOME In the phase FINALIZE Starts the Form tool 2 In the phase PREPARE in step A gn Starts the tool for importing a reference Model or Check Blockout if a jaw reference jaw is available NEN In the phase DES GN Starts the tool for inserting a closing edge Bom In the phase FINALIZE Starts the Surface pattern tool 3 In the phase DES GN f at least one Starts the tool for inserting a retainer pin retention plate is present 3 Jgmnthe phase FINALIZE Starts the Add Material tool EN EN In the phase DES GN if at least one Starts the tool for inserting an open end retention plate is present stop In the phase FINALIZE Starts the Support Tube tool Starts the tool for inserting a clamp Starts the Check Thickness tool inthe phase DESIGW Stets the tool or inserting a lingual bow In the phase DESIGN In the phase DESIGN Starts the tool for inserting a clamp ladder In the phase DESIGN Starts the tool for inserting a chin pad NE un mE IN EN 2 In the phase DESIGN element selected of the same type Case loaded Displays the tool wheel EN ME Lj X m H m p fess Sweat 65 3
12. 8 222 D3534 D3534 208 01 01 02 01 2015 41 8 Tips and Tricks Sirona Dental Systems GmbH 8 1 Shortcut keys Operator s Manual inLab Partial Framework tool open and OK Cance visible EE the step menu in the step menu Delete Element selected Deletes selected element Ec Element selected Deletes selected element key eum foo w Return No tool open and Ok Cance visible LEE the step menu in the step menu 65 38 222 D3534 42 D3534 208 01 01 02 01 2015 Sirona Dental Systems GmbH Operator s Manual inLab Partial Framework Index B Back protection plate 18 37 Base plate 18 34 adding 35 Grain 34 Hole 35 Thickness 34 Biogeneric copy 29 Blocking out wax 12 28 C Case Save 14 Save as 15 Chin pad 18 36 Clamp 17 30 Clamp ladder 17 31 Closing edge 17 32 Code libraries 15 COMPLETION 39 Connector 18 36 D Double arrow keys 13 E Elements Additional 19 fusing 12 Laminar 18 Linear 17 65 38 222 D3534 D3534 208 01 01 02 01 2015 F File format Older formats 8 PF 8 Form Apply material 21 Remove material 21 Smooth 21 Insertion axis select 27 Insertion direction 12 L Licenses 15 Lingual bow 18 35 M manual html format 8 pdf format 8 Material apply 12 Material thickness measure 12 Model align 12 assess 12 Model axis define 27 Model casting prosthesis 12 O Object bar 13 Open en
13. Drag Line button Select the active area the yellow part of the line by holding down the right mouse button and dragging the mouse up and down Drag the line by moving the mouse to the desired point Click on the Connector Edit Lines button Click on the Edit Line button Redraw the lines at the desired points by starting with a double click setting points with left clicks and ending the line by double clicking 65 38 222 D3534 D3534 208 01 01 02 01 2015 Sirona Dental Systems GmbH 7 Editing orders Operator s Manual inLab Partial Framework 7 5 DESIGN phase Creating a base plate with a hole 1 Draw the desired base plate 2 Select Display Objects in the side palette and click Base Plate The base plate is hidden Only the line of the base plate is visible 3 Select 7oo s in the side palette or Base P afe via the tool wheel 4 Inside the first base plate draw an additional base plate in the shape of the hole desired Adding a base plate gt Select Add Base P ate to set an additional base plate Lingual bow 1 Select Lingual Bar from the side palette or the tool wheel 2 Select the desired lingual bow thickness using the Thickness slide controller in the side palette 3 Click Surface pattern in the side palette if you would like to add a grain to the base plate 4 You must also observe the notes in the section Laminar elements gt 18 Changing the shape of the
14. Edit Lines button 2 Click on the Drag Line button 3 Selectthe active area the yellow part of the line by holding down the right mouse button and dragging the mouse up and down Drag the line by moving the mouse to the desired point 1 Click on the Connector Edit Lines button N Click on the Edit Line button Redraw the lines at the desired points by starting with a double click setting points with left clicks and ending the line by double clicking o Adding an open end stop gt Select Add Tilt Stop to set an additional open end stop Retainer pin 1 Select Retention Pin from the side palette or the tool wheel 2 Selectthe thickness of the tip of the retainer pin using the Diameter slide controller in the side palette 3 Select how long the retainer pin should be using the 7e ghf slide controller 4 Select how wide the base of the retainer pin should be using the Base Wiath slide controller 5 As soon as you move over a retainer pin with the mouse the pin hangs from the mouse pointer 6 Double click to set the retainer pin 65 38 222 D3534 D3534 208 01 01 02 01 2015 Sirona Dental Systems GmbH 7 Editing orders Operator s Manual inLab Partial Framework 7 6 COMPLETION phase Positioning the retainer pins 1 Double click on the retainer pin to activate it 2 Move the pin over the retention plate using the direction arrows at the base of the pin 3 Tilt the pin using th
15. N In this phase you can perform the following e Design elements of a model casting prosthesis e Position the elements COMPLETION In this phase you can perform the following e Elements are fused e Shape and process prosthesis e Apply material e Attach support pipes e Measure material thickness 65 38 222 D3534 12 D3534 208 01 01 02 01 2015 Sirona Dental Systems GmbH 4 User interface Operator s Manual inLab Partial Framework 65 38 222 D3534 D3534 208 01 01 02 01 2015 4 2 Object bar Object bar The jaw button is located in the object bar Tool wheel In the PREPARE and FINALIZE phases the tool wheel provides the most common tools for simplifying access In the DESIGN phase all the construction elements that can be used for designing a model casting prosthesis are located in the tool wheel 1 Right click in the workspace The tool wheel opens 2 Click with the right mouse button anywhere in the workspace The tool wheel moves to the position of the mouse pointer 3 Select a tool design element The selected tool is available The tool wheel closes automatically You also can close the tool by clicking in the workspace with the left mouse button Step menu Each phase is divided into steps They are shown in the step menu at the bottom edge of the screen The step menu changes depending on which phase the current restoration is in This menu guides you through the process step
16. New as of 01 2015 inLab Partial Framework Software Version 1 0 0 Operator s Manual Introduction 1 1 1 2 General data 2 1 2 2 Getting started 3 1 3 2 3 3 3 4 User interface 4 1 PhaseDa Rare irre ro nuca tea beu bod abeme beiden 4 T1 PREPARATION gerre Ailes 3ESION eMusic E 4 15 COMPLETION 1 poneret et Rb etre etri 42 Oeo ET m 43 TOOL WHDeelssceosoted e basse tiii TE csset aid 44 Step MENU uestes er bet st ena v d ih b M Sa SE 45 oystemuimelusauiate i tet lesa ehe tent A ma ta ies 4 5 SAVE CASE uni ipid need iceik god btt er eise US 4 5 2 Save the case under a different name 4 5 3 LICENSE MANAGEL ccccccceeccseeceeeseeeseeesees 4 5 4 Window mode ccc cec cee cc eee eeeeeeen sete eeaeeeeeens 4 5 5 Current program version 4 5 6 Close the software esseesse ontidulallolluss autom acter One atm cei renee Pe ce eoi S pM uota Dci pt 5 1 CHING S eaen cts olas kot ade paa Eas ME Tuba teu edid qus Ski omReSOLTIOLIOS Soumettre dte P c bU b ERES 5 1 2 Selecting a language Table of contents Dear CUSTOMER us isctiestv mte Evan M UU M Eo RE pube I LEE Copyright and trademark esee General safety information suus Structure of the manual eeeseeeeseeee 2 2 1 Identifica
17. Select the desired relief gap of the retention plate using the Inclination slide controller in the side palette 4 You must also observe the notes in the section Laminar elements gt 18 65 38 222 D3534 D3534 208 01 01 02 01 2015 33 34 e Changing the shape of the retention plate wW N Click on the Connector Edit Lines button Click on the Drag Line button Select the active area the yellow part of the line by holding down the right mouse button and dragging the mouse up and down Drag the line by moving the mouse to the desired point Click on the Connector Edit Lines button Click on the Edit Line button Redraw the lines at the desired points by starting with a double click setting points with left clicks and ending the line by double clicking Changing the shape of the hole 2 Select Square Holes in the side palette to obtain square holes Adding a retention plate gt Select Add Grid to set an additional retention plate Base plate 1 Select Base P ate from the side palette or the tool wheel 2 Select the desired base plate thickness using the 7hickness slide controller in the side palette 3 Click Surface pattern in the side palette if you would like to add a grain to the base plate 4 You must also observe the notes in the section Laminar elements gt 18 Changing the shape of the base plate w N Click on the Connector Edit Lines button Click on the
18. are is installed Uninstalling the software X The program is closed 1 Click on Start All Programs Sirona Dental Systems inLab Tools Deinstallation to uninstall the software During the uninstall procedure you will be asked whether you want to delete the patient data or the entries in the registration database e g the calibration data 2 Depending on your decision click either the Yes or No button The software is uninstalled 65 38 222 D3534 D3534 208 01 01 02 01 2015 9 3 Getting started Sirona Dental Systems GmbH 3 3 Copy protection Run Application 10 Operator s Manual inLab Partial Framework Copy protection The software can be started only when the USB license stick is plugged in The USB license stick is included in the scope of supply of the units If you require additional licenses please contact your dealer Always keep the USB license stick near the unit All authorizations grinding interface software licenses can be installed as electronic licenses on the USB license stick You must enter a 25 digit license key for this purpose You will receive the license key along with the unit Alternatively you can order it separately from your dealer Following an update you may require a new license that is not available on your USB license stick For more information refer to the section on License manager gt 15 Starting the software X The inLab SW software i
19. between the various editing modes using the space bar Retention plate There are different types for selection e with round holes e with square holes Base plate Lingual bow Chin pad Back protection plate e Is only displayed if a biogeneric copy has been scanned as well Open end stop 65 38 222 D3534 18 D3534 208 01 01 02 01 2015 Sirona Dental Systems GmbH 6 Construction elements Operator s Manual inLab Partial Framework 6 3 Additional elements Additional elements In addition to elements that have been created using line entries there are other elements that are created with other entries Description Retainer pin 65 38 222 D3534 D3534 208 01 01 02 01 2015 19 20 Editing orders The Shortcut keys 41 chapter describes how the following tools and options can be called using shortcut keys Tools and functions of the page palette The page palette offers you various different functions depending on the current step Views View Options You can use the View Options button to display 4 predefined views e Top e Bottom e Right e Left Changing the view 1 Click on the View Options button 2 Click on one of the proposed views V The virtual model rotates to the corresponding view Enlarging or reducing the view 1 Click on the View Options button 2 Position the mouse pointer over the center tooth icon and press and hold the left mouse butto
20. cording to US Federal Law this product may be sold only to or by instruction of physicians dentists or licensed professionals 65 38 222 D3534 D3534 208 01 01 02 01 2015 Sirona Dental Systems GmbH 2 General data Operator s Manual inLab Partial Framework 2 2 Structure of the manual Structure of the manual Identification of danger levels To prevent personal injury and material damage please observe the warning and safety information provided in this document Such information is highlighted as follows DANGER An imminent danger that could result in serious bodily injury or death A possibly dangerous situation that could result in serious bodily injury or death A possibly dangerous situation that could result in slight bodily injury NOTICE A possibly harmful situation which could lead to damage of the product or an object in its environment IMPORTANT Application instructions and other important information Tip Information on making work easier Formats and symbols used The formats and symbols used in this document have the following meaning Prerequisite Prompts you to do something 1 First action step 2 Second action step or gt Alternative action S Result gt Individual action step see Formats and symbols Identifies a reference to another text used gt 7 passage and specifies its page number Command menu item Indicates commands menu items or quotations 6
21. d stop 18 38 43 Sirona Dental Systems GmbH Operator s Manual inLab Partial Framework P Phase bar 12 COMPLETION 12 12 DESIGN 12 12 PREPARATION 12 12 Prosthesis process 12 shape 12 R Retainer pin 19 38 Retention plate 18 33 S Safety information 7 Shape Modifying the size 21 23 Software Uninstallation 9 Step menu 13 Support pipes attach 12 T Tool Shape 21 Tool wheel 13 Tools 20 V Views Change 20 Enlarge 20 Reduce 20 View options 20 Wax 28 65 38 222 D3534 44 D3534 208 01 01 02 01 2015 We reserve the right to make any alterations which may be required due to technical improvements Sirona Dental Systems GmbH 2015 Sprache englisch Printed in Germany D3534 208 01 01 02 01 2015 A Nr 000 000 a E Sirona Dental Systems GmbH in the USA FabrikstraBe 31 Sirona Dental Systems LLC Order No 65 38 222 D3534 D 64625 Bensheim 4835 Sirona Drive Suite 100 Germany Charlotte NC 28273 WWW sirona com USA
22. e direction arrows at the tip of the pin Adding a retainer pin gt Select Add Retention Pin to set an additional retainer pin IMPORTANT After setting the first pin another retainer pin will hang from the mouse pointer Guide the mouse to the position of the retainer pin and double click again to set another retainer pin COMPLETION phase When switching to the FINALIZE phase all constructed elements are totaled up to one element Shaping You can edit the model casting using the Form tool in the FINALIZE phase see also Form gt 21 65 38 222 D3534 D3534 208 01 01 02 01 2015 39 7 Editing orders Sirona Dental Systems GmbH 7 6 COMPLETION phase Operator s Manual inLab Partial Framework Adding material With the Add Materia tool you can place additional material onto the model casting see also Adding material 23 Adding support pipes You can attach support pipes for producing the model casting using the Support Tube tool see also Adding a support pipe gt 24 Exporting the model casting The model casting can be exported as an stl file via Export Framework in the step menu Here the model casting and the support tubes are exported IMPORTANT stl data format An appropriate license is required for exporting in the stl data format Sirona will not be held liable for the further processing of stl data in other external software 65 3
23. ectthe active area the yellow part of the line by holding down the right mouse button and dragging the mouse up and down Drag the line by moving the mouse to the desired point 1 Click on the Connector Edit Lines button Click on the Edit Line button Redraw the lines at the desired points by starting with a double click setting points with left clicks and ending the line by double clicking N Q A 65 38 222 D3534 D3534 208 01 01 02 01 2015 31 7 Editing orders Sirona Dental Systems GmbH 7 5 DESIGN phase Operator s Manual inLab Partial Framework Adjusting the clamp ladder V You have selected a closing edge g a Click on Edit Profile in the side palette Move the mouse over the element Anew profile disk is displayed Click to set a new profile disk Hold down the left mouse button and drag the mouse up or down to adjust the thickness of the profile Hold down the right mouse button and drag the mouse up or down to adjust the width of the profile Adding a clamp ladder gt Select Add Clasp Bar to set an additional clamp ladder Setting the closing edge Select Finishing Line from the side palette or the tool wheel Select the desired closing edge height using the Height slide controller in the side palette 3 You must also observe the notes in the section Linear elements gt 17 Changing the closing edge 1 Click on the Connector Edit Lines button 2
24. en Keep the license certificate with 25 digit license key ready which you either obtained with the unit or ordered separately from your dealer F The license manager is used for the installation of new software licenses f Tip You can also start the license manager via Start All Programs Sirona Dental Systems inLab Tools License Manager To activate the license you must have an Internet connection and the USB license stick must be connected Licenses and code libraries For information on licenses and code libraries from third parties see licenses pdf The file is in the installation directory under C Programs Sirona Dental Systems CADCAM Window mode The Window Mode function can be used to exit full screen mode or enter it again Current program version jE The About function contains information about the current program d version Close the software The Exit function can be used to close the software 65 38 222 D3534 D3534 208 01 01 02 01 2015 15 5 Configuration Sirona Dental Systems GmbH 5 1 Settings Operator s Manual inLab Partial Framework Configuration Settings Reset notes Description Displays all the deactivated warnings in the workflow again Warnings which were previously hidden remain hidden Selecting a language Here you can set the language of the software Once the software is rebooted the language is set to your choice 65 38 222 D3534
25. g Line You can change the lines of the elements with Drag Line 1 Click on the Connector Edit Lines button 2 Click on the Drag Line button 3 Selectthe active area the yellow part of the line by holding down the right mouse button and dragging the mouse up and down 4 Dragthe line by moving the mouse to the desired point Edit Line You can redraw the lines of a connector with Edit Line 1 Click on the Connector Edit Lines button 2 Click on the Edit Line button 3 Redraw the lines at the desired points by starting with a double click UN setting points with left clicks and ending the line by double clicking Editing profile You can edit the profile of clamp and clamp ladders with Edit Profile V You have selected a clamp or clamp ladder 1 Click on Edit Profile in the side palette amp 2 Move the mouse over the element Anew profile disk is displayed 3 Click to set a new profile disk 4 Hold down the left mouse button and drag the mouse up or down to adjust the thickness of the profile 5 Hold down the right mouse button and drag the mouse up or down to adjust the width of the profile 65 38 222 D3534 22 D3534 208 01 01 02 01 2015 Sirona Dental Systems GmbH 7 Editing orders Operator s Manual inLab Partial Framework 7 1 Tools and functions of the page palette Adding material You can add material to the model casting using this tool in phase FINALIZE 1 Click
26. le if a biogeneric copy wax up has also been scanned e 1 Select Backing Plate from the side palette or the tool wheel x 2 Select the desired bite block plate thickness using the Thickness A slide controller in the side palette 3 You must also observe the notes in the section Laminar elements 18 Changing the shape of the back protection plate 1 Click on the Connector Edit Lines button 2 Click on the Drag Line button 3 Selectthe active area the yellow part of the line by holding down the right mouse button and dragging the mouse up and down Drag the line by moving the mouse to the desired point 1 Click on the Connector Edit Lines button 2 Click on the Edit Line button 3 Redraw the lines at the desired points by starting with a double click ag setting points with left clicks and ending the line by double clicking Adding a back protection plate gt Select Add Backing Plate to set an additional back protection plate 65 38 222 D3534 D3534 208 01 01 02 01 2015 37 38 Open end stop IMPORTANT Open end stops can only be set under retention plates You adopt the thickness that has been set as nc ination gap for the respective retention plate 1 Select Tilt Stop from the side palette or the tool wheel 2 You must also observe the notes in the section Laminar elements gt 18 Changing the shape of the open end stop 1 Click on the Connector
27. lick on the Connector Edit Lines button N Click on the Edit Line button Redraw the lines at the desired points by starting with a double click setting points with left clicks and ending the line by double clicking d Adding a connector gt Select Add Connector to set an additional connector Chin pad 1 Select Rest from the side palette or the tool wheel e 2 Select the desired chin pad thickness using the 7 ckness slide p controller in the side palette 3 You must also observe the notes in the section Laminar elements gt 18 Changing the shape of the chin pad 1 Click on the Connector Edit Lines button 2 Click on the Drag Line button 3 Select the active area the yellow part of the line by holding down the right mouse button and dragging the mouse up and down 4 Drag the line by moving the mouse to the desired point 65 38 222 D3534 36 D3534 208 01 01 02 01 2015 Sirona Dental Systems GmbH 7 Editing orders Operator s Manual inLab Partial Framework 7 5 DESIGN phase Click on the Connector Edit Lines button 2 Click on the Edit Line button 3 Redraw the lines at the desired points by starting with a double click UN setting points with left clicks and ending the line by double clicking Adding a chin pad gt Select Add Resft to set an additional chin pad amp e d Back protection plate IMPORTANT The Backing Plate element is only availab
28. lingual bow 1 Click on the Connector Edit Lines button 2 Click on the Drag Line button 3 Selectthe active area the yellow part of the line by holding down the right mouse button and dragging the mouse up and down 4 Dragthe line by moving the mouse to the desired point 1 Click on the Connector Edit Lines button 2 Click on the Edit Line button 3 Redraw the lines at the desired points by starting with a double click w setting points with left clicks and ending the line by double clicking Adding a lingual bow gt Select Add Lingual Bar to set an additional lingual bow 65 38 222 D3534 D3534 208 01 01 02 01 2015 35 7 Editing orders Sirona Dental Systems GmbH 7 5 DESIGN phase Operator s Manual inLab Partial Framework Connector 1 Select Connectors from the side palette or the tool wheel e 2 Select the desired connector thickness using the Thickness slide NA controller in the side palette 3 Selectthe desired relief gap using the nc ination slide controller in the side palette 4 You must also observe the notes in the section Laminar elements gt 18 Changing the shape of the connector 1 Click on the Connector Edit Lines button 2 Click on the Drag Line button 3 Selectthe active area the yellow part of the line by holding down the right mouse button and dragging the mouse up and down Dragthe line by moving the mouse to the desired point 1 C
29. n The icon then changes to a magnifying glass 3 Pull the mouse button up or down The virtual model is then enlarged or reduced Tip You also can use the mouse scrollwheel to enlarge or reduce the view Tools The most important tools are also offered to you in the tool wheel The construction elements for the model casting are located in the DESIGN phase under Tools Undo and reset With the Undo button in the tools you can undo the last change made With the Resef button in the tools you can reset changes that were made with the tool 65 38 222 D3534 D3534 208 01 01 02 01 2015 65 38 222 D3534 D3534 208 01 01 02 01 2015 Form With the Forrn tool you can process the blocking out wax in the PREPARE phase and process the model casting in the FINALIZE phase With the Form function you can e apply e remove e or smooth material Tip If one of the Form tools is active you can switch to the following order using the space bar on the keyboard Apply gt Remove gt Smooth gt Apply gt Apply material 1 Click on the Form button 2 Click on the Add button 3 Click with the mouse cursor on the area you wish to shape 4 Press and hold the left mouse button and apply the material to the surface location by moving the mouse Removing material 1 Click on the Form button 2 Click on the Remove button 3 Press and hold the left mouse button and remove the material fr
30. nstalling the software The software requires the 2 00 firmware version of the license stick Update the firmware version if necessary For more information refer to the section on License manager gt 15 You need at least one inLab 4 PC for the software An inLab 4 PC V 3 0 1 is recommended Use the version of the license manager provided with this version to import licenses from the license certificate provided NOTICE An inLab SW 4 2 5 or an inLab 4 3 0 is required for installing the inLab Partial Framework module X The license stick firmware is available in version 2 00 V The PC is powered up and all programs are terminated Theinstallation file of the inLab Partial Framework is downloaded and saved onto the hard disk or onto removable data storage media 1 Goto the directory and start the file Setup exe 2 Inthe next dialog click the Nex button The license agreement is shown 3 Read through the license agreement carefully 4 f you accept the license agreement then activate the accept the terms in the license agreement option button and click the Next button 5 In the next dialog click the Nex button 6 Select to which inLab software version inLab Partial Framework should connect 7 Inthe next dialog click the ns a button The program continues the installation routine This may take several minutes 8 Click the Finish button once installation is complete The softw
31. om the surface location by moving the mouse Smoothing When smoothing you can smooth the surface locally 1 Click on the Form button 2 Click on the Smooth button 3 Click with the mouse cursor on the location you wish to smoothen 4 Press and hold the left mouse button and smoothen the surface location by moving the mouse Properties Modifying the size You can use the Size button to modify the size of the area affected The area affected is shown as an orange colored area The size of the area affected can be modified for each shaping tool 1 Click on the Form button 2 Click the Size button and press and hold the mouse button 3 Drag the mouse cursor up or down The size of the orange area is enlarged or reduced The size is shown on the restoration Tip You can also change the size by clicking on the restoration with the right mouse button and while holding the right mouse button down dragging the mouse up or down 21 7 Editing orders Sirona Dental Systems GmbH 7 1 Tools and functions of the page palette Operator s Manual inLab Partial Framework Adjusting thicknesses You can use the Strength button to modify the intensity of the area affected The thicknesses of the affected area can be modified for each forming tool 1 Click on the Form button 2 Click the Strength button and press and hold the mouse button 3 Pull the mouse cursor up or down Editing lines Dra
32. rk software back protection and bite block plates can be constructed in the next process The Backing Plate button will only appear if a biogeneric copy is available 7 5 DESIGN phase gt Select the elements from the side palette or gt Select the elements by right clicking in the main window via the tool wheel 65 38 222 D3534 D3534 208 01 01 02 01 2015 29 7 Editing orders Sirona Dental Systems GmbH 7 5 DESIGN phase Operator s Manual inLab Partial Framework Set clamps 1 2 3 You must also observe the notes in the section Linear Select C asp from the side palette or the tool wheel Select the type of clamp you want to use elements gt 17 Changing the clamp path 1 Click on the Connector Edit Lines button 2 Click on the Drag Line button 3 Select the active area the yellow part of the line by holding down the right mouse button and dragging the mouse up and down 4 Drag the line by moving the mouse to the desired point 1 Click on the Connector Edit Lines button 2 Click on the Edit Line button A Redraw the lines at the desired points by starting with a double click setting points with left clicks and ending the line by double clicking Adjusting editing the clamp profile X You have selected a closing edge g 30 Click on Edit Profile in the side palette Move the mouse over the element Anew profile disk is displayed
33. s installed You will find the start icon on the desktop X The USB license stick is connected with a valid current license X They are located in phase MODEL in the inLab SW software and a 3D model is already calculated 1 Open the software inLab SW 2 Click the Run Application button in the system menu inLab SW 3 Then click on the Partial Framework button The software is started Alternative start options X The inLab Partial Framework software is installed You will find the start icon of the inLab Partial Framework software on the desktop gt Double click on the start icon of the inLab Partial Framework software Or gt Select Sfart All Programs Partial Framework Partial Framework in the Windows Start menu 65 38 222 D3534 D3534 208 01 01 02 01 2015 Sirona Dental Systems GmbH 4 User interface Operator s Manual inLab Partial Framework 4 User interface Overview of the user interface e rennou fP anuon C Page ateto fe forme b semm 65 38 222 D3534 D3534 208 01 01 02 01 2015 11 4 User interface Sirona Dental Systems GmbH 4 1 Phase bar Operator s Manual inLab Partial Framework Phase bar The workflow is illustrated in the software in 3 phases Phase bar e PREPARE e DESIGN e FINALIZE PREPARATION In this phase you can do the following e Assess model e Align model e Define insertion direction e Process blocking out wax DESIG
34. tion of danger levels 2 2 2 Formats and symbols used 2 2 9 GONVERUOMS cocos ee or baee tee cox uci aiai 2 2 4 Formats of the manual 229 PIE TOR M A RTT Installing the software esses Uninstalling the software seeeeeeesssee COPY DIOLGCIOFI auct PC elegit elibapeso rue dedu hw ci PUR ion Ganeanes Starting the software eseeeseesseeeeee Oo O WMO CON NN O O Aaa A 65 38 222 D3534 D3534 208 01 01 02 01 2015 6 Construction elements dcs exotucidamtnbtntEbtet Qa dats veh cons ub b vested iouis uds GRO MUS 6 1 Linear elements suci oen nt st brine oria lr RE Pic pa en tu uat unl V ER RED Cerat 62 Eaminarelerents usc t t P eR be lt eub pu b tu D E RN Ee RA OR RN 5 9 JAggditional elemen GS aieo ecco outs eb Oe Dead amd h osa teducem fedis Dess UNDO 7 E CIN OTJE coe c d E E 7 1 Tools and functions of the page palette seeeseeeeeeesee EEL VIEWS m leke TOOS cr CRZ FO era OS 412 2 Eating INES cibi e eo be Eo a E IS E 701 2 9 Eding ProNET FZ Adding materialiter oco ac odo otn eE TMZ Addo a ON A ee ros i ee tal a hein ierat da 7 1 2 6 Adding a support pipe seeeeseeeeeeeeeeeeenee To IDISDIBV ODIGGCIS eite tiat a eu atit decade uud TD dABDOLVSIS TOOS uem oeeuie esi e ena aa est qud eque dace o
35. to strengthen the model casting using support pipes You can attach support pipes to the desired points using this tool in phase FINALIZE 1 Click on the Support Tube button 2 Start the process by double clicking on the desired point 3 Guide the mouse toward the end point of the pipes 4 To complete the pipes double click on the desired end point of the pipes Adjusting the size By holding down the right mouse button and dragging the mouse up and down you can adjust the diameter of the pipes Display objects The individual elements of the model casting or the jaw can be displayed or hidden in phases DESIGN and FINALIZE 65 38 222 D3534 24 D3534 208 01 01 02 01 2015 Sirona Dental Systems GmbH Operator s Manual inLab Partial Framework 7 Editing orders 65 38 222 D3534 D3534 208 01 01 02 01 2015 7 1 Tools and functions of the page palette Analysis tools Displaying rear sections The color scheme for the rear sections can be displayed or hidden on the model via the Undercut button 1 Click on the Analyzing Tools button 2 Click on the Undercut button The color scheme is displayed on the model The rear section depth can be read using the legend The start of the rear section is marked with a light blue line Material thickness The model casting material thickness can be assessed using a color scheme via the Check Thickness button The two blue balls on both sides show the
36. ue D ien esie 1 1 4 1 Displaying rear sections eeeeeeeeeeeesse 7 1 4 2 Material thickn Ss cccccccecceecseeceeceeeeeeceeeeeeeeeseeeees 7 2 Scanning the jaw in the inLab SW software ccccccceeeceeeseeeeeeeeeeetaeees 7 3 Starting inLab Partial Framework sirier ta Lo PREPARATION PHASE noa a e e aE CAL SeLMdElaX Seea a Nd 7 4 2 Selecting insertion AXIS cece cece ceeeeceeeeeeeteeeeseeeeaeeeseneeseeeseeeess L4 9 Shaping the Weser e a oi TAA BOJNEC CODY sxaiatutestisnt dd PET coton esie ano eee oU SD LU uda TD DESIGN PNIS E sane nar eai e Mv c ecu db HR xn du au Rr EM 06 010 mU 5 2 Clamp adde ssnssssessbissnsadescbut dt natum capitu dace Sud eH or SeeT tuti 7 0 3 Set ng the closing edge ive deese ee daa od LOU uu Mo iaa bed 1 9 4 xetenlor lale sucer eter entes etr et e Pv bd ce totes CR Ul gre op T2050 Base pale ana a a cuu bai aant debates MA s MUR c uo spat ER KO IMIG UMA DOW EMEN RTI TOF CONECO uoeiesi victa ai aos erun NEP PUE uncirat aD EM CEUPAD DR DEED 150 9 xr padsissieusde tone tu c wig eat evecare 71 5 9 Backbrotection pale ier Rh hi Ree to c o RO d TIO VO Open end stops datei telum Ee Eb E FS EE iniu LO AOMPEEUOBDDIASO crastina doa Hd ag npo altre Rated Ett RUMOR POM ASMA meret rH 1 6 2 Adna materal ssirssraioi auteni entero nte aate bate oue i 65 38 222 D3534 D3534 208 01 01 02 01 2015 17 17 18 19 20 20 20 20 2
37. work software on the desktop gt Double click on the start icon of the inLab Partial Framework software Or gt Select S art All Programs Partial Framework Partial Framework in the Windows Start menu The scanned model is loaded into the inLab Partial Framework software If a biogeneric copy has been scanned this is also loaded into the inLab Partial Framework software 65 38 222 D3534 26 D3534 208 01 01 02 01 2015 Sirona Dental Systems GmbH 7 Editing orders Operator s Manual inLab Partial Framework 7 4 PREPARATION phase PREPARATION phase Set model axis Set the axes for model alignment Please ensure a consistent representation here This alignment is required to create optimal view options and initial suggestions gt Align the model to the orientation of the jaw Each tooth must be in its respective quadrant IMPORTANT If the model axis has already been defined in the inLab SW software this is adopted in the inLab Partial Framework software Selecting insertion axis Tip When setting the insertion axis the blocking out wax is displayed in light blue 1 Select the insertion axis for how you want to block out the jaw To do this pull on the ball in the target disk or move the yellow arrow over the model 2 Confirm the selected insertion axis by clicking Ok 65 38 222 D3534 D3534 208 01 01 02 01 2015 of 7 Editing orders Sirona Dental Systems GmbH 7 4 PREPARATION phase
Download Pdf Manuals
Related Search