user manual - Tanning Bed Parts
Contents
1. Burns easily and severely and tans minimally Exposure Times Follow the guidelines for skin type and exposure times as shown in the table be low Untanned persons should not tan on consecutive days during their first week of tanning Never tan more than once a day Tanning normally appears after the first few sessions and maximizes after approximate ly four weeks Tan once or twice per week thereafter to maintain appearance Persons already having a base tan may begin at ad vanced levels corresponding to the extent of their base tan DANGER Shock hazard Do not operate this device near water or while you are wet A DANGER Some medication may increase your sensitivity to ultraviolet light It is recommended that you consult a physician before using this sunbed if taking any medication or if you suspect that your skin might be especially sensitive to sunlight MAXIMUM EXPOSURE TIME IS 15 MINUTES Level 1 Week 1 1st 3rd Sessions NOT RECOMMENDED FOR TANNING 3 6 9 4 11 Level2 Level3 Level4 Level5 Burns minimally tans easily and above average 13 Ultimate Envy 234 Assembly and User Manual 41 The Keypad Your sunbed has been designed with the user in mind Every effort has been made to ensure easy operation A Display Four digit alphanumeric display shows re maining time as well as bed operation B STOP Interrupts tanning session C START TIME Begins tanning session See more in The Tan2. 0 J c 0 E Les U 4 J 30062 01A 48 MONTH GOLD MEDAL WARRANTY Your ETS Distributor including ETS LLC if purchased directly through a manufacturer s warranty warrants your tanning unit to be free of structural defects in mate rial and workmanship under normal use for its lifetime Your ETS Distributor will at its discretion repair any structural defect which materially affects the performance of the tanning unit or replace the tanning unit For forty eight 48 months following the purchase date of your tanning unit your ETS Distributor will provide replacements for parts that prove to be defective in ma terial or workmanship with the following exceptions gas springs ballasts and electronic lamp starters are war ranted against manufacturer s defects for a period of one 1 year glow tube lamp starters and cracked or broken endcaps are warranted against manufacturer s defects for a period of ninety 90 days fluorescent lamps are war ranted against manufacturer s defects for a period of thirty 30 days acrylics are warranted against manufacturer s defects for a period of one 1 year prorated following the purchase date of your tanning unit Shipping charges will be covered during the first ninety 90 days following the purchase date Your ETS Distributor including ETS LLC if purchased directly also extends to you a two 2 year parts warranty on all T Max remote system compon
3. Manager Series with Wireless combo Connect one G2 with Pow er Injector to the Manager and one G2 to a wireless ready tanning bed The rest of the salon may be daisy chained together and connected to the wireless equipped tanning bed eliminating the need to wire the Manager to the tanning beds T 1j Non T Max incorporated units 38 Ultimate Envy 234 Assembly and User Manual 30062 01A VLO c900 Scenario 4 T Max Manager Series with Wireless combo 2 Wireless can be easily added to an existing salon already utilizing T Max Connect one G2 with Power Injector to the Man ager and one G2 to each wireless ready Rx tanning bed The rest of the salon may be daisy chained together and connected to the Manager NU _ Non T Max incorporated units Scenario 5 T Max Manager Series with wires As always this tanning bed is fully ay compatible with a wired T Max system Simply connect the RJ 22 modular cable s described in the T Max Manager manual into either of the smaller remote port s located on the back of the bed and follow the instructions that came with your remote system incorporated units Scenario 6 Single Bed wired to T Max 3W In single sunbed installations the T Max 3W can offer the same control as the T Max Manager eliminating the need for a Manager After you have set the T Max 3W s address to 0 refer to your T Ma
4. bench along the front are two supports for the bench acrylic Swing them up to hold the bench acrylic open To remove the bench acrylic simply pull it out of the channel at the back The canopy acrylic is secured by 5 screws along the front edge of the canopy Use a Phillips screwdriver to unscrew all 5 screws and the aluminum channel will swing down to release the acrylic The screws will remain captive in the channel Swing the channel open fully and the front edge of the canopy acrylic will drop down To remove the canopy acrylic disconnect the exciters and lift it out of the channel along the back edge When you are finished reverse the above directions to secure the acrylic shields Acrylics vary greatly over time in their abil ity to effectively transmit UV light Acrylics sold by ETS have been life tested to ensure proper transmission throughout their useful life Replace any acrylic that appears damaged This includes deep scratches many small scratches gouges and cracks A WARNING Shock hazard Disconnect power before removing any protective covers Removing Replacing Fluorescent Lamps After opening the acrylics replace lamps as follows 1 Grasp the lamp at one end and at the middle and turn the lamp one quarter turn Gently remove the lamp from its holders 2 Reinstall the lamp by inserting the pins located on the ends of the lamp into the slots on top of the lamp holders and turn
5. mode and cycle power to the bed 50 Ultimate Envy 234 Assembly and User Manual 30062 01A VLO c900 Parameter Function Default Pi Bed Address 1 104 Set to 255 to restore factory defaults of all parameters 1 P 2 Beep Mode adjusts loudness of beeps 0 3 1 IP Session Delay minutes 1 P5 Session Count adjustable P 6 Lamp Hours adjustable P 7 Bed Hours not adjustable P8 Manual Sessions counts sessions in stand alone mode P 9 Clean Bed Indicator O off 1 on 1 P10 Manual Lockout disable stand alone mode 0 off 1 on 0 P13 After Session Cool down minutes 3 minimum 10 maximum 5 P15 Master Session Count not adjustable P 16 Max Volume 0 min 9 max 9 PIZ Allow User to Decrease Time 0 off 1 on 0 P18 Default Session Volume during session 0 min 9 max 6 PIO Enable Remote Function with Control Relay 0 off 1 on 0 P 20 Enable LED effect 0 off 1 on 1 Phi Pause Countdown 0 off 1 on 0 P 23 Auto Restart session resumes after momentary power outage O off 1 on 0 P 30 Audio Source at Idle O SALN 1 MP3A 2 ZEN 3 FM 5 MP3B 6 DMx 2 P31 Enable SALN speaker level input on back of bed 0 off 1 on 5 P 32 Enable ZEN soft music 0 off 1 on 3 P 33 Enable MP3 user input O off 1 on 1 Syl Enable FM 0 off 1 on 5 P35 Enable AUX 0 off 1 on 0 P 36 Enable PATCH 0 off 1 on 2 P 37 Enable DMX Input 0
6. a base tan may begin at advanced levels cor responding to the extent of their base tan RECOMMENDED EXPOSURE TIMES IN MINUTES MAXIMUM EXPOSURE TIME IS 15 MINUTES Level 1 Week 1 Skin Type 1st 3rd Sessions Sensitive Skin Burns easily and severely and does not tan NOT RECOMMENDED FOR TANNING Level2 Level3 Level4 Level5 I Light Burns easily and severely and tans minimally 3 6 9 Ill Normal Burns moderately and tans average 4 11 IV Dark Burns minimally tans easily and above average 5 New lamps emit approximately 10 more ultraviolet radiation during the first 50 hours of operation Recommended tan ning times should therefore be reduced by approximately 10 during that period WARNING Read the instructions booklet before using this sunlamp product All persons in the room should wear protective eyewear when lamps are on Recommended eyewear provided eyeshields or equivalent eyewear as defined under 21 CFR 1040 20 Other types of eyewear may not provide adequate protection Failure to use protective eyewear may result in severe burns or other eye injury If discomfort develops discontinue use and consult a physician THE FOLLOWING LAMPS HAVE BEEN CERTIFIED FOR USE IN THIS EQUIPMENT BRONZING SUN ULTRA Wolff Model BSU 71 T12 120W BI PIN Heraeus OH C 400 EF facial unit Disconnect power before attempting to clean relamp or engage in the maintenance of this product THIS EQUIPMENT MUST BE EARTH GROUNDED NTERTE T
7. off 1 on 1 P 38 LED Mode O off 1 fadel 2 fade2 3 fade3 4 blue 5 red 6 green 1 P51 Key Beep Enable beep every time a key is pressed 0 off 1 on 1 P52 End of Session Beep 0 off 1 on 1 P 81 FM Preset 1 example set to 923 for radio station FM 92 3 881 P 82 FM Preset 1 example set to 923 for radio station FM 92 3 881 P 83 FM Preset 1 example set to 923 for radio station FM 92 3 881 P 84 FM Preset 1 example set to 923 for radio station FM 92 3 881 P 85 FM Preset 1 example set to 923 for radio station FM 92 3 881 Ultimate Envy 234 Assembly and User Manual 51 N 89 226cm Weight approximate 00 81 1 lbs 369kg ROOD SIZE arroan ei 9 2 7m x 7 2 4m Voltage 230 VAC AMP TABE relate TES 1P 20A EEEE A EE A EE EE 3P 12A Circuit Breaker recommended min 1P 35A SP POULE 3P 20A O tleto sincan ne aoas Hardwire only ets A 46 11 70m Mam EaP S sesiis uns sun 34 x 120W Face Tanner Lamps if equipped 3 x 400W Body Cooling esenee 1100cfm Foot Fan Main Timer System Digital Back up Timer s ssssess Secondary Solid state Max Exposure TIME savrssssiussvssius 15 minutes Remote Capability T Max Wireless Ready Record this information for ease of service Date of purchase Serial number Model number Proudly manufactured in the U S A 1e800 449e3605 7445 Company Drive Indianapolis IN 46237 9296
8. off the bed Be careful of the body fan power cable Next to the body fan is a USB extension cable with a USB flash drive attached Un screw the clip holding the cable and push the USB cable through the pedestal Ultimate Envy 234 Assembly and User Manual 11 Remove both pieces from each end and set The acrylic end supports are held in place aside The bench endcaps are held in place by 4 by 5 10 32x1 flat head screws each 10 32x1 screws each VLO c900 12 Ultimate Envy 234 Assembly and User Manual VLO c900 The front cross member is held in place with 4 5 16 18x1 hex socket bolts Ultimate Envy 234 Assembly and User Manual 13 a 20A 0089 Aes ee Oo 7009 n0 20087 peg ngas ae FLOOR PROTECTOR PANEL Next remove the bench lamp box Four 10 32x1 2 screws hold the box in place You may find it helpful to remove a lamp or 2 to access the screws at the foot end Also remove the 6 10 32x1 2 screws holding the fan plenum to the back panel This ple num routes air from the cooling fans through s the lamp box Carefully lift the lamp box out of the bench being careful not to damage the plenum Three 10 32x1 2 screws hold the floor protector panel Remove it and set aside PLENUM 14 Ultimate Envy 234 Assembly and User Manual 30062 01A VLO c900 Close the canopy and reinstall the shipping pi
9. the front cross member and se cure by tightening the 4 screws tucked into the channel as indicated below Ultimate Envy 234 Assembly and User Manual 33 Slide the bench acrylic into the aluminum Loosen the 5 captive screws holding the channel at the back of the bench Secure the front canopy acrylic channel The channel acrylic in place with the 2 1 4 20x1 Phil will swing down but remain in place Next lips screws at the front corners place the back edge of the canopy acrylic into the channel at the back of the canopy Plug the wiring harness from the exciters to the harness in the bed Swing the acrylic closed and lock the front edge by swinging the front channel closed and secure the 5 screws 34 Ultimate Envy 234 Assembly and User Manual 30062 01A VLO c900 Electrical Connections This unit must be hardwired directly to a junction box on a dedicated circuit ETS recommends connection by a professional electrician On the back of the bed at the foot end is a box that protrudes through the back panel see below Make the connection to power inside this box Remove the 4 screws holding the cover plate and remove the cover plate from the box Inside is a connection bus for power You may wire the bed to either a 3 phase circuit 3 wire plus ground or single phase circuit 2 wire plus ground Follow the diagram at right for connection instructions Your sunbed arrives from the fa
10. the lamp a quarter turn It should click in place Replacement Lamps To be assured of maximum tanning effec tiveness change lamps after approximately 800 1000 hours of use Lamps used longer than that begin to lose their tanning effec tiveness even though they continue to light We recommend using the lamps specified below Use of uncertified lamps is a viola tion of Federal regulations and will void your warranty The following lamps have been certified for use in your tanning bed BRONZING SUN ULTRA Wolff Model BSU 71 T12 120W BI PIN Heraeus OH C 400 EF facial unit Ultimate Envy 234 Assembly and User Manual 45 Removing Replacing Face Tanner Lamp After opening the canopy acrylic replace the face tanner lamp as follows 1 The face tanner glass is held in place by two metal brackets Support the face tanner glass with your hand while un screwing the two screws on one of the brackets The face tanner glass will slip out of the other bracket 2 The lamp can now be exchanged Sim ply pull the face tanner lamp toward you to remove it from the socket Install the new lamp using a clean cloth or paper towel by inserting it into the lamp sock et Ensure that the lamp is firmly seated in the lamp socket Note Never take hold of the lamp such that your fingers are in contact with the lamp glass Finger oils will greatly reduce the lamp s operational life 3 Slide the face tanner glass into the brac
11. ART TIME button C to be gin the tanning session The lamps will turn on and the timer will begin to count down from the maximum time If a less er time is preferred repeatedly press the START TIME button to decrease the time When the timer reaches 0 the lamps turn off If you want to stop your ses sion before time expires press the STOP button B You will have ten seconds to restart with the remaining time other wise the timer will enter the cool down mode Raise the canopy by using the canopy handle do not push up on the acrylic The cooling fans run for 5 minutes after the lamps shut off to aid in cooling the sunbed During this time the display will repeatedly flash COOL and then the remaining cool down time After cool down the timer display re turns to 0 Operation while connected to a T Max remote system If using other remotes or no remote system see left 1 Lift the canopy lie down on the bench face up lower the canopy toward your body using the canopy handle For best results position the canopy as close to your body as possible 2 Put on your safety goggles 3 Assuming the remote system has been set to allow a pre tanning delay time the timer display A will repeatedly flash DEL and then the remaining delay time Press the START TIME button C or wait until the delay time has expired to begin the tanning session The lamps will turn on and the t
12. CHASE PRICE RECEIVED OR FOR LOSS OF USE OR PROFITS LOSS OF TIME INCONVENIENCE RENTAL OR SUBSTITUTE PRODUCTS LOSS OF BUSINESS LOSS OF INCOME OR ANY OTHER IN CIDENTAL INDIRECT SPECIAL OR CONSEQUEN TIAL DAMAGES Some states do not allow the exclu sion or limitation of incidental or consequential damages and the above limitation or exclusion will not apply to residents of some states This 48 Month Gold Medal Warranty gives you specific legal rights and you may have other rights which may vary from state to state All warranty service must be performed by an autho rized service person using only ETS authorized replace ment parts Use of non authorized parts may void your warranty All labor charges must be authorized by your ETS Distributor prior to the start of repairs and must not exceed the established rates and time allotment policies established by your ETS Distributor If your tanning unit must be returned for service within thirty 30 days from the purchase date freight charges will be paid for by your ETS Distributor after which all freight charges shall be at your expense Contact your ETS Distributor for the authorized Service Center nearest you This war ranty is serial number specific and only applies to tanning units purchased through an authorized ETS Distributor This warranty is extended to the individual or legal entity whose name appears on the original sales document and may not be transferred to any other
13. In Canada call 1 800 661 6292 or 519 421 1212
14. and User Manual 21 Put the rear panel in place inside the chan nels in the pedestals and slide the pedestals together to sandwich the panel Secure the panel with 8 10 32 x 1 2 screws from the front side BACK PANEL 22 Ultimate Envy 234 Assembly and User Manual 30062 01A VLO c900 Slip the rear cross member into the cradles on each pedestal and secure with 4 10x1 2 Phillips sheet metal screws on each end The rear angle cover attaches between the rear panel and rear cross member with 16 10 32x1 2 screws along the angled flanges Note To avoid stripping sheet metal screws use this simple technique Using a hand screwdriver slowly turn the screw counter clockwise until it clicks in place Then turn it clockwise until hand tight Do not over tighten Ultimate Envy 234 Assembly and User Manual 23 Slide the timer contactor boxes through the rear panel and secure them to the left ped estal with 4 10 32x1 2 screws in each box Secure the covers on the boxes as you will not need to get inside them anymore 24 Ultimate Envy 234 Assembly and User Manual 30062 01A VLO c900 Slide the canopy frame in place in the ped estal cradles as shown and fasten with 5 3 8 20x1 hex bolts on each cradle Ultimate Envy 234 Assembly and User Manual 25 Attach the canopy endcaps with 4 10 32x1 Phillips screws in each VLO c900 Ult
15. ct power before removing any protective covers Cleaning the Canopy and Bench 1 Open the acrylics and remove lamps as described on the next page 2 With a soft cloth wipe the entire length of each lamp to remove any film build up 3 Clean both sides of the acrylics with a non ammonia disinfectant cleaner 4 Wipe the reflectors with a clean damp cloth 5 Reinstall the lamps and acrylics 6 Use a vacuum cleaner to clean all fan openings Mechanical Inspection Your tanning bed has been built for years of service To ensure trouble free operation throughout its life inspect the unit s me chanical integrity every 400 500 hours of use e Inspect the unit s fasteners verifying that all are firmly in place e Inspect the lift system for proper opera tion The canopy should raise and lower with minimal effort using the canopy handle Contact a servicer to adjust or replace if necessary e Inspect all wiring connections Contact a servicer if any connections seem loose e Inspect the AC power cord and its con nections e Inspect the acrylic Broken cracked or badly scratched acrylics should be im mediately replaced 44 Ultimate Envy 234 Assembly and User Manual 30062 01A VLO c900 Opening Replacing Acrylics The bench acrylic is secured in place by 2 screws at the front corners Use a Phillips screwdriver to remove the screws The acryl ic will lift up in front On the inside of the
16. ctory wired for single phase To convert to 3 phase sim ply disconnect the Blue Black and Blue Red wires from the terminal block slide them out of the current sensors and connect to L3 Be sure to provide a proper strain relief for the incoming power line The conduit fitting hole on top of the box is sized at 1 1 4 3 Phase Wiring GND L3 L2 LI GND L2 LI NOTE Not shown in the diagram above are three thin wires a red black and blue one Do not move these thin wires Only move the thick er blue wires with colored stripes Ultimate Envy 234 Assembly and User Manual 35 Audio Your sunbed is equipped with a unique sound system exclusive in the tanning in dustry that provides full rich sound without the use of unsightly add on speakers This Cathedral of Sound transforms the entire canopy acrylic into the speaker by trans mitting vibrations into the tanning area This arrangement contains the sound within the tanning tunnel much better than any other system available Simply speaking you get better sound with very little noise pollution for the rest of the salon compared to tradi tional speaker systems Your sunbed comes from the factory equipped to connect the speaker out from a stereo system to the spring type speaker level inputs on the back of the bed shown below directly over the power box In this configuration full musical control resides in the stereo system The bed
17. cuit breaker on a 3 phase line 3 wire plus ground Alternatively it requires a minimum 30A circuit breaker on a single phase line 2 wire plus ground See page 35 CAUTION Use of a voltage source above 245V AC may prevent proper operation of the sunbed and could cause damage and void the warranty 6 Ultimate Envy 234 Assembly and User Manual 30062 01A VLO c900 Disassembly Your new tanning bed arrives completely assembled The reason for this is to assure everything has been tested at the factory Therefore you must first disassemble the bed before moving it into the salon room To avoid possible assembly issues if you find you can move the unit without further disassembly feel free to do so and begin the assembly process at a suitable step Remember to save all hardware removed It will all be used during reassembly Shipping Pin First remove the shipping pins locking the canopy down and raise the canopy Press ing the canopy down slightly will loosen the pins so they can be removed easily Ultimate Envy 234 Assembly and User Manual 7 Remove the bench and canopy acrylics The bench acrylic is secured by 2 1 4 20x1 Phillips screws at the front corners Remove the screws and simply raise the acrylic slightly and pull free of the alumi num channel at the back Five captive screws across the front of the canopy hold the canopy acrylic in place Loosen these screws and the fr
18. ent remote connection scenarios Find the scenario that best fits your application Three remote ports are located on the back panel directly above the power box two RJ 22 4 wire ports for daisy chain remote connections and one RJ 11 6 wire port for wireless remote connection T Max Products The T Max remote systems offer the ulti mate in sunbed control while allowing the tanner easy straightforward operation Your sunbed is configured to directly connect to this system including the wireless remote system The circuitry inside your sunbed eliminates the need for the T Max 3W or the older 1A and 3A when connecting to the T Max Manager series Your sunbed supports the auto addressing feature of the T Max Manager models and many pa rameters See your T Max manual for de scriptions of these parameters and how they function REMOTE PORTS RJ 22 RJ 11 wired wireless T Max Wireless Remote System The T Max G2 eliminates wires in your sa lon allowing easy setup without hiring an electrician to run wires It also protects your investment from damage by isolating each unit from one another Your sunbed arrives wireless ready which means it connects directly to the T Max G2 wireless system Older tanning beds and T Max managers may also utilize this system but require a T Max Power Injector PI to provide the needed power to the G2 wireless unit Remote System Hook up Sce
19. ents External volt age transformers buck boosters are covered by a one 1 year parts and labor warranty provided you send back the defective transformer Labor costs associated with repair or replacement work covered by this warranty will be reimbursed for repair or replacement work required to be performed for a period of ninety 90 days following the shipping date of your tanning unit Normal wear and tear damage from misuse or abuse damage incurred in transit or damages resulting from unauthorized repairs or modifications are not cov ered by this warranty Warranty coverage does not include cosmetic abnormalities such as scratches nicks dents or other cosmetic changes that do not materially interfere with the function of the tanning unit THIS 48 MONTH GOLD MEDAL WARRANTY IS EXPRESSLY MADE IN LIEU OF ANY OTHER WAR RANTIES EXPRESS OR IMPLIED INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABIL ITY AND FITNESS FOR A PARTICULAR PURPOSE WHICH ARE HEREBY DISCLAIMED No one has the authority to change or modify this 48 Month Gold Medal Warranty in any respect To obtain service under this 48 Month Gold Medal Warranty contact your authorized ETS Distributor or ETS LLC if purchased directly Proof of purchase including serial number is required IN NO EVENT SHALL YOUR DISTRIBUTOR OR THE MANUFACTURER BE LIABLE AT LAW OR IN EQUITY FOR ANY LOSS LIABILITY DAMAGE OR EXPENSE IN AN AMOUNT IN EXCESS OF THE PUR
20. ervice CAUTION Proper assembly of your sunbed requires 3 4 people Plan to have some helpers assist you 4 CAUTION DO NOT lift the unit using the plastic endcaps They are not designed to hold the weight of the unit and may break causing damage to the unit and possible injury CAUTION Air from the room is used to cool the sunbed Maximum ambient room tem perature should be 80 F Place your sunbed no closer than 3 from any wall Make sure nothing obstructs the airflow into or out of the fan openings A poorly ventilated room may cause the unit to become hot and cause dis comfort to the user Pre installation Planning The following instructions outline a com plete disassembly and reassembly Prepare an area for disassembly to place items prior to installation in the final space No hardware has been provided as the hard ware needed will be removed during the disassembly process Be sure to keep track of all hardware removed Electrical Requirements You are responsible for preparing the facility for your tanning bed Please have an electri cian present at the time your tanning bed is installed That way the installation crew can fully verify all functions before they leave This unit runs on 220VAC service and must be hardwired directly to a junction box on a dedicated circuit A professional electrician is recommended for electrical installation This unit requires a minimum 20A cir
21. he front of the canopy so it does not fall Remove the canopy BELLOWS Ultimate Envy 234 Assembly and User Manual 17 On the foot end pedestal are two metal box es with wire harnesses coming out of them Open the boxes by removing the sheet met al screws holding the cover panels You may only need to remove a few screws to slide the covers off Inside the boxes are 4 10 32x1 2 screws in each which hold the boxes to the pedes tal Remove these eight screws and carefully slide the lower box out of the back panel The two boxes are connected together Box screws are inset 18 Ultimate Envy 234 Assembly and User Manual 30062 01A VLO c900 Remove the 16 10 32x1 2 screws hold ing the rear angle panel and set the panel aside The rear cross member sits in cradles on each end and is secured in place with 8 10x1 2 sheet metal screws Remove the screws and slip the cross member out of the cradles REAR ANGLE PANEL REAR CROSS MEMBER Ultimate Envy 234 Assembly and User Manual 19 The back panel attaches to the pedestals with 8 10 32x1 2 screws Remove the screws and separate the pedestals to release the panel Be sure to hold the panel as it may topple BACK PANEL 30062 01A 20 Ultimate Envy 234 Assembly and User Manual VLO c900 Assembly Place the pedestals in the salon room ap proximately where the bed will be Ultimate Envy 234 Assembly
22. his product is in conformity with performance standards for sun lamp products under 21 CFR PART cu 1040 20 and ANSI UL Standard 482 Certified to CAN CSA Standard C22 2 NO 224 c US LISTED 88465 4 Ultimate Envy 234 Assembly and User Manual 30062 01A VLO c900 D AN G F Ro ultraviolet Veuillez suivre les instructions vitez une exposition excessive Tout comme pour les rayons du soleil une exposition excessive peut causer des blessures aux yeux et la peau et provoquer des r actions allergiques Une exposition r p t e peut causer le vieillissement pr matur de la peau et provoquer le cancer de la peau PORTEZ DES LUNETTES PROTECTRICES LE NON RESPECT DE CETTE CONSIGNE DE S CURIT PEUT ENTRA NER DE GRAVES BR LURES OU DES L SIONS OCULAIRES LONG TERME Les m dicaments ou les produits cosm tiques peuvent augmenter votre sensibilit au rayonnement ultraviolet Consultez un m decin avant d utiliser la lampe solaire si vous prenez des m dicaments si vous souffrez d une maladie cutan e ou si vous croyez tre particuli rement sensible aux rayons du soleil Si vous ne bronzez pas au soleil il est peu probable que vous bronzerez sous une lampe solaire Les enfants les personnes g es et les personnes qui ont une peau claire qui br le facilement ne bronze jamais ou alors tr s peu ne devraient pas utiliser cette lampe Etendez vous sous la partie sup rieure puis abaissez celle ci aussi bas que possible N utilisez
23. imate Envy 234 Assembly and User Manual 26 VLO c900 If you retightened the screws for the Total Access Panel during disassembly loosen them again now and slide the canopy cover panel behind the access panels The front of the canopy cover sits in the front aluminum channel Secure the cover by tightening the loosened screws The front is held in place with 2 10 32x1 flat head screws inserted up through the front ends of the endcaps As with the access panel screws if you re tightened the screws for the rear corner cov ers loosen them now Slip the rear corner covers into place and tighten the screws to secure them Ultimate Envy 234 Assembly and User Manual 27 Pull the shipping pins out of the lift system and open the canopy Slide the floor pro tector panel against the foot end corner as shown and secure in place with 3 10 32x1 2 screws Slide the bench lamp box into place Be careful of the fan plenum on the underside of the lamp box Four 10 32x1 2 Phillips screws hold the box down You may need to remove a lamp or 2 to access the holes Six 10 32x1 2 Phillips screws hold the fan plenum to the back panel 28 Ultimate Envy 234 Assembly and User Manual 30062 01A VLO c900 Install the front cross member using 2 5 16 18x1 hex socket bolts in each end Ultimate Envy 234 Assembly and User Manual 29 Install the bench acrylic supports with 5 Ins
24. imer will begin to count down When the timer reaches 0 the lamps turn off If you want to stop your ses sion before time expires press the STOP button B The timer display will blink and continue to count down Press the START TIME button C to restart your session Your session ends when the tim er reaches 0 Raise the canopy by using the canopy handle do not push up on the acrylic The cooling fans run for 5 minutes after the lamps shut off to aid in cooling the sunbed The timer will indicate DRTY as a reminder to clean the sunbed After the sunbed is cleaned press the START TIME button and the display will return 10 07 Ultimate Envy 234 Assembly and User Manual 43 Care and Maintenance Cleaning After Use Clean and disinfect your tanning bed s bench and canopy after each use Use a non abra sive disinfectant cleaner that does not con tain ammonia or ammonia derivatives Am monia may damage the acrylic shield Spray the acrylic lightly with disinfectant and wipe dry with a clean soft cloth We recommend Australian Gold pH Neutral Disinfectant Cleaner Thorough Periodic Cleaning The cooling fans draw air through the bed and over time will cause a dust buildup on the lamps and reflectors This will reduce the tanning effectiveness of the bed When a dust buildup is observed it is necessary to thoroughly clean the inside of the bench and canopy A WARNING Shock hazard Disconne
25. individual or legal en tity This warranty is void if the tanning unit is modified in any manner from its original design To obtain warranty service contact your place of pur chase Proof of purchase including serial number is required for verification Contact ETS LLC only if you purchased your equipment directly 2 Ultimate Envy 234 Assembly and User Manual 30062 01A VLO c900 Thank you for purchasing this tanning bed It has been designed to provide years of de pendable service for you Please read all the instructions in this booklet before installing and using the unit Always be sure to observe all safety precautions Contents Unpacking and inspection sses 6 Pre installation Planning sun 6 Electrical R quir ment usant 6 Disassembly s 7 ASSEMIDIY Sa anne 21 Electrical Connections usant 35 AUO teen ee Pree pen Peer en errr a N 36 Mood Mode Lighting sent 36 Remote CONNECTIONS este 37 T Max Products 37 T Max Wireless Remote System 37 Remote System Hook up Scenarios 37 DH TION sense 41 Before YOUN TaN siccvetiassatnsataisbeeustaersenetig 41 EXDOSUrS TIMES stands 41 The le pad sn 42 The Tanning SSS OG ss aa 43 Care and Maintenance n 44 Cleaning After Use seeen 44 Thorough Periodic Cleaning 06 44 Cleaning the Canopy and Bench 44 Mechanical Inspection eee eee 44 Opening Replacing Acrylics s s s 45 Removing Replacing Fluore
26. is just a speaker For more musical options including sooth ing zen music Mp3 input DMX control FM tuner and voice assist contact your ETS representative for upgrade options LEFT SPEAKER IN RIGHT SPEAKER IN Mood Mode Lighting Along with an exciting new sound system this sunbed incorporates changing and changeable lighting to accent the idle bed Change the lighting to suit your particular salon surroundings or your current mood The LED modules used to accent the tanning bed require no regular maintenance and are rated to last the entire life of the bed If you wish to change the look of the Mood Mode lighting follow these steps 1 With the bed sitting idle Display show ing O press and hold the FAN button for 5 seconds Listen for the confirma tion beep and the display will change to MOOD 2 Use the and or buttons to scroll through the available lighting modes including 3 speeds of fade and 3 static colors 3 Press STOP to exit the Mood Mode set up 36 Ultimate Envy 234 Assembly and User Manual 30062 01A VLO c900 Remote Connections Your sunbed incorporates advanced circuit ry allowing it to connect and communicate with most remote control systems If a re mote system is to be used first determine whether the remote system is a T Max Sys tem or a standard remote system operating with a control relay The following pages outline many differ
27. ket attached to the bed and lock it in place with the other bracket and two screws 4A DANGER Unfiltered light from face tanner can cause severe burns Never turn sunbed on while face tanner is disassembled or when glass filters are removed Immediately discontinue use of this equipment if face tanner glass is broken or any unfiltered light can be seen escaping face tanner assembly 46 Ultimate Envy 234 Assembly and User Manual 30062 01A VLO c900 ISSUE RESOLUTION Sunbed not tanning 1 Clean sunbed see Thorough Periodic Cleaning 2 Ensure supply voltage is between 208 and 230V AC 3 Replace lamps if lamp hours are greater than 800hrs 4 Replace acrylic Lamps fail to light and timer 1 Make sure the unit is connected to a power source display is blank 2 Check source of AC power Reset circuit breaker or re place fuse One or more lamps fail to 1 Check that lamp is installed correctly light 2 Switch unlit lamp with a lamp that lights if new lamp lights and old lamp still does not replace old lamp The face tanners will not 1 Face tanners will not relight for 1 minute if turned off come on 2 Replace face tanner lamp see Removing Replacing Face Tanner Lamp forgot what address or Press the STOP button and without releasing it press the id set my sunbed to START TIME button to enter parameter mode Parameter 1 shows the bed address See Parameters Timer display is indicating Curren
28. narios Follow the diagrams on the next few pages to see the many different scenarios for hooking up your salon If you need further assistance call T Max directly at 417 338 5101 CAUTION The remote connection is not designed to supply or accept high voltage nor can it provide power to an external timer The sunbed s remote interface circuitry operates on 5 volts attempting to connect it to any higher voltages will damage the sunbed as well as void your warranty Ultimate Envy 234 Assembly and User Manual 37 Scenario 1 T Max Manager Series with Complete Wireless Connect one G2 with Power Injector to the Manager and one G2 nee mt ee like with this configuration Units that do not commu nicate with T Max will need a G2 and a 3W to operate If you have an older T Max Manager that doesn t support auto addressing set the address of each sunbed manually as de scribed in Setting the address manually You can place your sunbed at any location in the series T t _ Non T Max incorporated units Scenario 2 T Max 3W with Wireless In single sunbed installations the TMax 3W can offer the same control as the T Max Manager eliminating the need for a Manager C After you have set the T Max 3W s address to 0 refer to your T Max user s guide and the sunbed s address to 1 simply connect one G2 to the T Max 3W and one G2 to the tanning bed Scenario 3 T Max
29. nbed must first be set Set the id manually as described below 1 With the bed sitting idle power on but not tanning press the STOP button and without releasing it press the START TIME button listen for the confirmation beep 2 The display will change to PRAM for 2 seconds then P 1 for 2 seconds then show the parameter value 3 Use the and or buttons to change this number to the desired address 4 Press the STOP button to return to idle 40 Ultimate Envy 234 Assembly and User Manual 30062 01A VLO c900 Operation Before You Tan Before using your sunbed please note the following important precautions e Your skin should be free of cosmetics oils or other body lotions prior to tan ning except for those specifically made for use with tanning devices However do not remove natural body oils by bath ing or showering immediately before tanning Your hair should be free of gels mouss es sprays or other hair products prior to tanning These products can cause damage to the sunbed acrylic As an al ternative a shower cap or towel can be worn to keep treated hair away from the sunbed surfaces e This unit intended for individual use Only one pair of eyewear is included RECOMMENDED EXPOSURE TIMES IN MINUTES Skin Type Sensitive Skin Il Light Ill Normal IV Dark Burns moderately and tans average Burns easily and severely and does not tan
30. ning Session D Plus Minus Controls bed functions for up or more and for down or less When bed is idle or during regular operation these buttons control music volume if equipped with audio option E FAN Press to enter body fan control mode Display changes to FAN and current fan speed Use to increase speed and to decrease Speeds offered are off 1 2 and 3 F FACE Press to enter face tanner control mode if equipped Display changes to FACE and then OFF or ON Use to turn face tanners on and to turn off Note Face tanners need a minute to cool down before relighting There may be a delay when turning face tanners back on during a session G MUSIC if equipped with audio option Press to enter music control mode Display will change to show current music option Press repeatedly to change the music option H VOICE Press to disable voice assist if equipped Press again to enable voice assist 42 Ultimate Envy 234 Assembly and User Manual 30062 01A VLO c900 The Tanning Session Operation as a stand alone unit or con nected to a remote system using a control relay If using T Max see right 1 Lift the canopy lie down on the bench face up lower the canopy toward your body using the canopy handle For best results position the canopy as close to your body as possible 2 Put on your safety goggles 3 Press the ST
31. ns to hold the lift system in place Remove the canopy cover and rear corner covers The back of the canopy cover includes the metal panel Loosen the 8 1 4 20 Phillips screws securing the back covers just a few turns Do not remove these screws The front corners of the canopy cover are held by 1 10 32x1 flat head screw in each corner Remove these screws Carefully lift the cov er from the bed The rear corner covers are attached with 6 10x1 2 screws each Simply loosen these screws and the covers will slip off A WARNING Lift springs under extreme tension Failure to properly install the shipping pins could result in damage to the unit and or personal injury when removing the canopy Ultimate Envy 234 Assembly and User Manual 15 The canopy endcaps are attached with 4 10 32x1 Phillips screws each Remove both endcaps 16 Ultimate Envy 234 Assembly and User Manual 30062 01A VLO c900 On the back of the canopy toward the foot end is a rubber bellows protecting the wir ing from the bench to the canopy Discon nect one end of the bellows by loosening the clamp holding it in place Pull the cables from the canopy out of the bench You may find it helpful to tape or tie the cables up so they do not get in the way when moving the canopy Remove the 5 3 8 20x1 hex bolts on each end of the canopy that attach it to the lift system Make sure something or someone is holding t
32. ont channel will swing down The screws will remain in the channel Swing the channel down farther to release the acrylic and lower the acrylic to clear the handle Attached to the canopy acrylic are 2 exciters speakers Disconnect the white connector on the wiring harness running from these exciters into the bed Now lift the acrylic out of the back chan nel 8 Ultimate Envy 234 Assembly and User Manual 30062 01A VLO c900 Tucked inside the aluminum channel that supports the bench acrylic are 4 Phillips flat head screws Loosen these screws a few turns to release the clamps holding the front skirt Do not remove the screws Now tip the skirt forward and lift off the pegs at the bottom Ultimate Envy 234 Assembly and User Manual 9 Find the harnesses under the bench and dis connect them all Don t worry about mixing them up They are all keyed to only connect to their proper mate Most harnesses connect with locking re ceptacles like the one shown below Sim ply squeeze the wings on either side and pull the connectors apart Do not pull on the wires A few of the connectors have a wire tie around them This wire tie is removable and does not need to be cut 10 Ultimate Envy 234 Assembly and User Manual 30062 01A VLO c900 The body fan is held in place with 2 10 32x1 2 screws at the bottom Remove these screws then lift the body fan assembly straight up and
33. otection fournies ou l quivalent tel que le stipule le document 21 CFR 1040 20 Les autres types de lunettes protectrices peuvent ne pas assurer une protection ad quate Utilis sans lunettes protectrices ce produit peut causer des br lures ou l sions oculaires graves Si vous souffrez d un malaise arr tez l utilisation et consultez un m decin SEULES LES LAMPES SUIVANTES ONT T HOMOLOGU ES POUR CET QUIPEMENT BRONZING SUN ULTRA Wolff Mod le BSU 71 T12 120W BI PIN Heraeus OH C 400 EF unit faciale s il y en a un TERTE D brancher l alimentation lectrique avant de nettoyer l appareil d en faire l entretien ou de changer les lampes r Cet quipement doit tre mis la terre c S LISTES Ce produit est conforme aux normes de rendement pour les lampes solaires dans le documents 88465 21 CFR partie 1040 20 ANSI UL 482 CAN CSA C22 2 N 224 Ultimate Envy 234 Assembly and User Manual 5 Unpacking and inspection Your new tanning bed arrives completely assembled The reason for this is to assure everything has been tested at the factory Be fore performing any work inspect the unit carefully and identify any issues that may have happened during shipping Notify the transportation company immediately to re port any shipping damage Record the serial number of the unit in the area provided at the back of this manual This information will be required whenever you call customer s
34. pas la lampe sans les panneaux de plastique transparents La premi re semaine de bronzage les personnes qui n ont pas un h le initial ne doivent pas se faire bronzer tous les jours Ne vous faites jamais bronzer plus d une fois par jour Le bronzage commence normalement appara tre apr s les premi res s ances il atteint son apog e au bout d environ quatre semaines Les personnes qui ont d j un teint h l peuvent commencer des niveaux plus lev s selon l importance de leur hale initial TEMPS D EXPOSITION RECOMMAND EN MINUTES LE TEMPS D EXPOSITION MAXIMAL EST DE 15 MINUTES Elev 1 Semaine 1 Type de peau 1ere 3e Peau sensible br le facilement et ne bronze pas NON RECOMMAND lev 2 lev 3 Elev 4 Elev 5 Il Peau claire br le facilement et bronze tr s peu 3 6 9 Ill Peau normale br le et bronze de fa on mod r e 4 7 11 IV Peau fonc e br le tr s peu bronze plus facilement que la moyenne 5 9 Les lampes neuves mettent approximativement 10 de plus de rayons ultraviolets au cours des 50 premi res heures de fonctionnement Le temps de bronzage doit donc atre r duit d environ 10 pendant cette p riode AVERTISSEMENT Lisez le livret d instructions avant d utiliser cette lampe solaire e Les autres personnes pr sentes dans la pi ce doivent aussi porter des lunettes protectrices lorsque les lampes sont allum es Coquilles de protection pour les yeux recommand es Les coquilles de pr
35. scent Lamps 45 Replacement Lamps ns au 45 Removing Replacing Face Tanner Lamp 46 Updating Timer Software 50 Parameters a scisvsensacsersdsasnsspeacsvaanneseepeveanes 50 Ultimate Envy 234 Assembly and User Manual 3 D N G E Ultraviolet radiation Follow instructions Avoid overexposure As with natural sunlight overexposure can cause eye and skin injury and al lergic reactions Repeated exposure may cause premature aging of the skin and skin cancer WEAR PROTECTIVE EYEWEAR FAILURE TO MAY RESULT IN SEVERE BURNS OR LONGTERM IN JURY TO THE EYES Medications or cosmetics may increase your sensitivity to the ultraviolet radiation Consult physician before using sunlamp if you are using medications or have a history of skin problems or believe yourself especially sensitive to sunlight If you do not tan in the sun you are unlikely to tan from the use of this product Children the elderly or fair skinned people who always burn easily and either never tan or tan minimally should not use this equipment To use lie down under canopy and pull down as far as adjustment will allow Do not use without clear plastic panels in place Untanned persons should not tan on consecutive days during their first week of tanning Never tan more than once a day Tanning normally appears after the first few sessions and maximizes after approximately four weeks Tan once or twice per week thereafter to maintain appearance Persons already having
36. t it must be the only file on the drive to work properly Updating the timer software 1 With the bed idle display showing 0 press and hold the STOP button until the display changes from 0 to Id 2 Within 5 seconds press the FAN button and the display will show PGM indi cating it is ready to program the timer 3 Press the START TIME button to begin programming the bed The display will show WAIT 4 After the update is complete the timer will reset and the bed will be ready to go once the timer display reads 0 In the event you receive an email contain ing an update file the email will contain full instructions on this procedure as well as the verification process to make sure the update was successful Parameters 1 With the bed idle display showing 0 press the STOP button and without re leasing it press the START TIME but ton The display will change to PRAM briefly then P 1 to signify parameter 1 then the parameter value 2 Use the and or buttons to change the parameter value 3 Press the START TIME button to advance to the next parameter 4 Press STOP to return to idle The next page shows the parameters that can be changed by the salon owner Refrain from changing any parameters not listed as bed function may be adversely affected To reset the bed to factory defaults set the Bed Address P 1 to 255 exit parameter
37. t sensor with the black wires running through it has E 8 detected that the bed is on when it should be off Timer display is indicating Current sensor with the Red wires running through it has E9 detected that the bed is on when it should be off Timer display is indicating Bed is off when it should be on E10 Timer display changes to in 1 If remote is being used other than T Max Manager the dicate a tanning time after external timer may not be activated the timer button is pressed 2 Remote wiring is incorrect see the instructions provided but lamps do not come on with the remote interface kit Timer display continues to 1 T Max Manager remote system has not yet been set show a 0 after the timer but 2 Sunbed address is not set correctly see Remote Connec ton is pressed tions Ultimate Envy 234 Assembly and User Manual 47 ISSUE My bed is connected to a T Max remote system but am having trouble getting into parameter mode My bed connected to a T Max Manager did not dis play dL but does indicate 0 a tanning time and the lamps have come on a tanning time but the lamps have not come on When auto addressing the first bed does not register an ig My salon suffers frequent short power outages and clients complain about los ing session time RESOLUTION You have probably attempted to connect your sunbed to the remote system already Disconnect the remote plug s from the ports a
38. t the back of the sunbed wait 90 seconds and try again Remote device has not been set The sunbed has not been connected to the remote system see Remote Connections Delay time of T Max Manager has not been set Delay time has expired and session has begun Auto start function of T Max Manager has been turned off Press the START TIME button to turn on lamps When using the auto address feature of the T Max Man ager you must wait 10 seconds from the time you start the auto address function before addressing the first bed If you have a T Max Manager changing parameter 23 from 0 to 1 will allow the tanning bed to remember how much time was left when power goes out and resume its session after power is restored See Parameters 48 Ultimate Envy 234 Assembly and User Manual 30062 01A VLO c900 Notes Ultimate Envy 234 Assembly and User Manual 49 Updating Timer Software Hanging on the foot end of the bed next to the body fan is a cable with a USB flash drive This flash drive contains a single file which is the timer software During normal use the flash drive may be removed as it does not interface with the timer However if ETS releases a new software update you can easily update the timer Be sure to keep the flash drive with the bed It contains one file and must not be used for any other purposes Updates will be emailed to you to copy onto this drive from any computer bu
39. tall the bench endcaps with 4 10 32x1 10 32x1 flat head screws each Phillips screws each VLO c900 NN A Ultimate Envy 234 Assembly and User Manual 30 VLO c900 Slip the USB extension cable through the Install the body fan First slip the power hole in the pedestal and secure the hanging cable through the hole in the left pedestal Then engage the hanging clips and finally secure with 2 10 32x1 2 screws in the bottom mounting flanges clip with a 10x1 2 screw Ultimate Envy 234 Assembly and User Manual 31 Connect all cables under the bench that were disconnected before Remember they are all keyed differently If it doesn t fit it connects to another harness Here s a checklist Harness from canopy Wire Colors anopy Power Blue Red ace Tanners Multi Face tanner ballast box an cord Black J 45 timer display Black xciters Red Black Ground wire reen Green wire from contactor box Bench lamp box Blue Black Contactor Box Black Red Face tanner ballast box Power in Black Cord from bench lamp box Body Fan Power Blue Black Green Yellow Contactor Box Connects to From timer box to remote board 32 Ultimate Envy 234 Assembly and User Manual 30062 01A VLO c900 Slip the hooks at the bottom corners of the skirt over the pegs on the pedestals and swing the skirt up The forks at the top of the skirt slip into the clamps along
40. x user s guide and the sunbed s address to 1 simply connect the RJ 22 modular cables described in the T Max user s guide directly into either of the smaller ports located on the back of the bed and either port on the back of the T Max 3W Ultimate Envy 234 Assembly and User Manual 39 Scenario 7 Non T Max Remote System wired to unit Most non T Max remote systems control the sunbed by the use of a relay The relay operates the sunbed by connecting and dis connecting a pair of wires leading from the sunbed Refer to the user s manual provided with your remote system to determine if it operates in this way To connect your sun bed to this type of system a remote interface kit is required Contact your place of pur chase to obtain the kit The illustration be low details a typical connection Follow the instructions provided with the kit and from the remote s manual to make the necessary connections Non T Max Remote System using control relay Remote nterface Kit CAUTION The remote connection is not designed to supply or accept high voltage nor can it provide power to an external timer The sunbed s remote interface circuitry operates on 5 volts attempting to connect it to any higher voltages will damage the sunbed as well as void your warranty Setting the sunbed address manually Before connecting your sunbed to the T Max Manager or T Max 3W the address of your su
Download Pdf Manuals
Related Search