USER`S MANUAL FOR G33™
Contents
1. First remove the magnifier from the rail Leaving the quick detach lever in its open position turn the unit upside down exposing the rail interface To loosen the adjustment turn the dial counterclockwise To tighten turn the dial clockwise Once done re mount the optic to the rail Continue incremental changes until a desired fit is achieved CAUTION Never make adjustments while the quick detach lever is in the closed position MAINTENANCE Maintenance of the magnifier is limited to cleaning of the outside housing of the optic and cleaning the lenses The optical system is coated with anti reflection material When cleaning the glass surfaces first blow away any dirt and dust Fingerprints and lubricants can be wiped off with lens tissue or a soft cotton cloth which is moistened with lens cleaning fluid or glass cleaner sold in any camera store Never clean the glass surface with a dry cloth or paper towel always dampen the glass surfaces prior to cleaning No maintenance is needed on the magnifier s surface except to occasionally wipe off with a soft cloth Use only a water based cleaner such as glass cleaner ammonia or soap and water Never use any solvent type cleaner such as alcohol or acetone WARNING NEVER DISASSEMBLE YOUR MAGNIFIER The optical cavity is purged nitrogen filled and sealed to achieve fog proof performance Disassembly will void the warranty and damage the sight If the switch action of the switch to Side mo2. be necessary to reposition the reticle image into the center of the magnifier window This is aesthetic in nature and has no affect on the sight s zero Turn the horizontal and vertical adjustments on the top or side of the magnifier by hand with a coin or a flat head screwdriver to reposition reticle to the desired position VERTICAL HORIZONTAL ADJUSTMENTS Switch operation To switch the magnifier to the side simply push the optic to the right or left depending on how it is mounted To close the mount push the magnifier back into its original position until a hard stop is achieved ADJUSTABLE Diopter ADJUSTMENT Lockine Quick DETACH DIAL BUTTON LEVER ApdJusTMeNT DIAL m Cross Bott Quick DETACH LEVER O LOCKING BUTTON Figure 4 Figure 5 INSTALLATION To install the configured magnifier onto the weapon open the quick detach lever To do this use your thumb to depress the locking button see Figure 4 Once depressed swing the quick detach lever open and away from its nested position Place the mount in the desired position behind the HWS Once the mount is located in the desired position push the magnifier forward until the cross bolt of the magnifier is set into the slot located on the mount Close the quick detach lever If the mount is too loose or tight for your specific rail adjustments can be made for a proper fit see Figure 5
3. to the mount It is user configurable based on the specific model HWS it will be mounted behind The 7mm riser included may be required to align the magnifier optical axis with the sight Only HWS models with 4 side buttons or quick detach levers require the use of the riser For all other HWS models the riser should not be used The magnifier system can be configured to switch to the left or to the right based on shooting preference Typically right handed shooters prefer the mount to switch to the left and left handed shooters to the right To configure your HWS you will need a screwdriver not included If the spacer is not used the shorter screws should be selected The longer screws are used with the spacer only If the spacer is being used place the spacer on the optic mounting interface Open the STS mount Position the mount on the optic mount interface or riser so it opens either to the left or right based on preference Insert each screw through the components and tighten securely ADJUSTABLE DIOPTER The G33 optic includes an adjustable diopter that allows the user to customize the focus to their particular vision This feature ensures a crisp clean aiming dot for more precision and shot placement To adjust simply grasp the diopter with the thumb and fore finger and turn either clockwise or counter clockwise until a clear sight picture is achieved ADJUSTABLE DIOPTER After zeroing or re zeroing the sight it may
4. Fixed 3X Eye Relief 2 2 55 8mm Field of View 7 3 degrees Length 3 9 99mm Weight 6 loz 174g Water Resistant 33 ft 10m Sealing Fog resistant internal optics allow left or right flip Finish Non reflective Rubber coated Rail Interface 1 Weaver or MIL STD 1913 with Quick Optical Axis Adjustment Internal adjustment Detach lock Retrofits to all HWS models with 7mm riser Magnifier Interface User configurable height with quick detach mount BASIC OPERATION The G33 magnifier is designed to be used behind an L 3 EOTech Holographic Weapon Sight HWS The magnifier can be mounted directly behind the HWS Simply switch the magnifier out of the way and operate the sight When used with HWS models 518 558 556 517 EXPS or 516 HWS with side button interface the user can easily operate the sight even with the magnifier in the locked position Positioning the Reticle Once the magnifier is installed properly behind the HWS it may be necessary to re zero the sight This may be due to the shooter s ability to see the target and Point of Impact POI more accurately than without the magnifier Re zeroing the sight will prevent a perceived shift in POI when going from no magnification to magnification OPTIC CONFIGURATION iWiniiour Rasy The L 3 EOTech Holographic Weapon Sight HWS product line has two different heights above the rail based on user preference For this reason the mag nifier does not come preassembled
5. USER S MANUAL FOR G33 EOTech tr For use with G33 Magnifiers or HHS Systems INTRODUCTION Thank you for purchasing L 3 EOTech s new Generation III 3X magnifier These magnifiers offer users of the Holographic Weapon Sight all models the additional advantage of vastly improved target recognition and increased lethality at medium i range distances The new Switch to Side STS mount allows aaa 4 the user the ability to engage the enemy with confidence in a ETS Close Quarters Battle CQB situation or at distances out to 600 U g meters or more This user manual describes the features of the L 3 EOTech Magnifiers and provides information on their use and maintenance Please read the instructions carefully before mounting and using the magnifiers Always practice proper firearm safety Included e 3x Magnifier e Switch to Side STS Mounte 7mm Riser 4 Screws The G33 is controlled under the Export Administration Regulations EAR ECCN 0A987 and may not be exported to a foreign person either in the U S or abroad without a license or exception from the U S Department of Commerce SPECIFICATIONS Switch to Side STS Mount Length 1 66 42 2mm Height 1 18 30mm Clears common low profile flip up rear iron sights Weight 2 9 oz 81g Color Finish Non reflective black with hard coat finish Switch Orientation Ambidextrous mount Flip Orientation to 3x Magnifier Magnification
6. ipping address and failure description in the email or on a voice mail This will allow the manufacturer to generate a Return Authorization Number RA to include with the sight s DO NOT SHIP THE SIGHTS WITHOUT A RETURN AUTHORIZATION NUMBER this will severely delay the turn around time on repair or replacement 4 If you require fill out a DD Form 1149 to include with the sight s you will return Include a reference to the RA and a signature line for L 3 EOTech s Service Department to sign indicating the receipt of mate rials The signed copy will be mailed faxed or emailed back to you upon receipt of the sight s for the purposes of accountability 5 Ifthe manufacturing date located on the bottom of the sight is more than two years old a fee will be assessed for repair to include the cost of both parts and labor A purchase order will be required to process the repair Please contact L 3 EOTech for an estimate Please send the unit postage prepaid to address listed in Appendix B Please include your name address telephone number and a written description of the problem you are encountering and also include the RA Whenever possible ship the sight in its original box FACTORY CONTACTS Prodtict Repistt ations uusii scvssccesosessesbagestsseatesesasqvarsssersss esuccoasets www eotechinc com product registration Customer Service Repait sscccissscscesissoosscscissecsscosisteosscesisteosseossstoossecezsrsesscoisnasc
7. setsttarsdasietepasesdisetneseaseetts 888 EOTHOLO 734 741 8868 x2176 Link to website to submit RA Request cesccseseesesseseeseseeseeeeseens http www EOTech inc com raform php Technical Sales Ser vice scstissscccsossssscessstsossusscsseesesobestasnvsataoiusiscesssesszacusesveazusobebiasavcedsvsusavcclastsopscuteonssress 888 EOTHOLO Shipping Address L 3 EOTech Inc 1201 E Ellsworth Rd Ann Arbor MI 48108 USA general L 3com com wWww L 3com com eotech
8. unt begins to stick from wear use a common spray lubricant on the hinge portion of the mount No other maintenance is needed on the Switch to Side Mount other than cleaning the surface Please follow the same guidelines when cleaning the magnifiers WARRANTY L 3 EOTech warrants every product to be free from defects in materials and workmanship for a period of two years from the original date of purchase L 3 EOTech will promptly repair or replace at its option any product that is defective in material or workmanship without charge All costs associated with the product shipment for product repair will be incurred by the owner This warranty does not cover defects caused by improper handling unauthorized disassembly installation or maintenance abnormal use or unapproved alterations L 3 EOTech shall not in any event be liable for any damages including any lost profits lost savings or other incidental or consequential damages arising out of the use or inability to use such products See L 3 EOTech s Standard Terms and Conditions for complete details Contacting the manufacturer for repair 1 Visit the manufacturer s website at https www L 3com com eotech Click on the Customer Service Tab in the menu bar and follow the instructions 2 Call or email L 3 EOTech s Customer Service Department at the following 734 741 8868 x2176 general L 3com com 3 Be sure to leave a name contact number return sh
Download Pdf Manuals
Related Search