User Manual - WDC Networks
Contents
1. 06 01 A slowly and make sure the equipment is mounted on the wall with the support of the screws 3 Product Installation 3 3 Cable and Wire Connection 3 3 1 Connecting Optical Fiber Jumper Cable and wire description The PON interface of the AN5506 01 A can be uplinked to the central office end OLT equipment via the optical fiber Connection procedures Step 1 Plan the layout of the optical fiber jumper Measure the distance from the PON interface of the AN5506 01 A to the ODF distribution frame and choose the optical fiber with an appropriate length for connection Step 2 Loosen set screws on the fiber cover that is at the upper right corner on the bottom panel of the equipment and remove the fiber cover Step 3 Take off the anti dust caps of the optical fiber jumper and the PON interface of the AN5506 01 A Step 4 Connect one end of the optical fiber jumper to the ODF distribution frame Step 5 Insert the other end of the optical fiber jumper to the PON interface at the bottom panel of the AN5506 01 A Step 6 Fit on the fiber cover and fasten set screws 3 Product Installation When fitting on the fiber cover pay special attention to the Caution layout of the optical fiber and make sure they are smoothly led out of the wiring hole When the optical fiber jumper is not used cover the AN5506 01 A s optical interfaces and fibers with anti dust caps to protect them from the dust and moisture which may da2. An Expert in Optical Communications FiberHome User Manual AN5506 01 A GPON Optical Network Unit Version A Code MN000000943 Date December 2011 FiberHome Telecommunication Technologies Co Ltd Version Version Description 4 LA FibverHome are trademarks of FiberHome Telecommunication Technologies Co Ltd Hereinafter referred to as FiberHome All brand names and product names used in this document are used for identification purposes only and are trademarks or registered trademarks of their respective holders All rights reserved No part of this document including the electronic version may be reproduced or transmitted in any form or by any means without prior written permission from FiberHome Operation Safety Rules Po A High optical power can cause bodily harm especially to eyes Never look directly into the end of the optical transmitter fiber jumper or the end of its active connector Exercise care if you must bend fibers If bends are necessary the fiber bending radius should never be less than 38mm Power socket overload broken cables or broken plugs may cause electric shock or fire Regular check ups on power supply wires and cables are essential If any appear damaged replace at once Use the power supply adapter provided in the package only Using other adapters may cause equipment damage or operation failures Install the equipment in a well ventilated environment
3. aged please contact local agencies of FiberHome immediately 3 1 2 Installation Precaution Before installing the AN5506 01 A please read the following thoroughly The installation location must be free of excessive moisture and must be properly grounded for lightning protection The selected installation position enables the connection between the AN5506 01 A and the outside For example there should be sufficient outlet space for power cables and network cables The installation position guarantees adequate air flow to facilitate heat dissipation The installation position provides good earth grounding conditions 3 Product Installation 3 2 Equipment Mounting The AN5506 01 A can be either secured on a stable plane like an office desk or hung vertically against the wall based on your demand The two mounting methods are introduced below Desk top mounting Take out the AN5506 01 A from the carton Before delivery four self adhesive pads are pasted to the four corners on the bottom of the device Gently place the AN5506 01 A on a stable surface that guarantees ventilation on both the left and right sides Wall mounting Step 1 According to the recesses distance of the AN5506 01 A drive the two mount to wall screws delivered with the equipment into the wall Step 2 Align the recesses on the bottom of the AN5506 01 A with the il screws on the wall and fix them up gently Step 3 Take your hands off the AN55
4. apter Connection procedures Step 1 Take out the DC power adapter with two conductors provided in the AN5506 01 A package Step 2 Insert the plug at one end of the adapter into the 12V DC interface of the AN5506 01 A Step 3 Insert the other end of the adapter into the mains supply socket Mains supply ON OFF Power Reset LAN Figure 3 3 Connection diagram for power cables Note 1 This power adapter can convert 220V AC into 12V DC input to provide power supply for the AN5506 01 A 3 4 Inspection after Installation After you have completed the wire and cable connection and subscribed the relevant services it is necessary to power on and check the AN5506 01 A as below Step 1 Turn on the power supply 3 Product Installation Step 2 Step 3 Step 4 Step 5 Observe the status of the power indicator LED If the power indicator LED is illuminated the equipment is normally powered on Otherwise check whether the power cable connection is correct Observe the status of the optical signal indicator LED If the optical signal indicator LED is extinguished the fiber connection is normal Otherwise check whether the optical fiber is correctly connected Observe the status of the network interface indicator LED If the network interface indicator LED is illuminated or blinking the network cable connection is normal Otherwise check whether the network cable is correctly connected During the equipment op
5. d forwarding Performs various QoS functions supports global configuration of queue priority flexible mapping of 802 1p value of packets and the strict priority queue scheduling mode Supports the AES 128 algorithm for data encryption of downlink data 1 2 Product Type Table 1 1 lists the type and number of the interface supported by the AN5506 01 A Table 1 1 Product type and its interface number Product Type Ethernet FE Ethernet GE Power Supply interface interface Jack AN5506 01 A 1 2 conductor power socket 1 3 Technical Specification Table 1 2 lists the technical specifications of the AN5506 01 A Table 1 2 Technical specifications of the AN5506 01 A Type Hem Description Service Supports the IEEE 802 1Q VLAN parameter standard Supports adding 802 1Q VLAN in tag or untag mode 1 Product Description Type hom Description The full 4096 VLAN address space is supported MAC address MAC address The MAC address table size is 64 The MAC address table size is 64 address table size is 64 Supports IGMP Snooping and IGMP Multicast Proxy protocols Supports IGMP v1 v2 v3 Wire speed L2 L3 switching All interfaces support the wire speed forwarding Supports 802 1p supports the QoS classification policy based on interface MAC address and VLAN ID Supports priority re tag Network side GPON One compliant with the ITU T G 984 interface interface series of s
6. eration ensure the ventilation to avoid abnormal events caused by overheating When any abnormality occurs contact the local office of FiberHome for replacement All indicator LEDs are extinguished after power on 1 Check whether the power cable is correctly connected 2 Check whether the power switch on the equipment s rear panel is in the ON position The equipment fails to work 1 If the equipment works abnormally check whether the power is connected normally or the voltage is not within specifications If the equipment is overheated check the ventilation Make sure the equipment is not exposed to direct sunshine or is near the heat source The optical signal indicator LED is illuminated 1 Check the received optical power levels with an optical power meter Excessively low receive optical power may indicate the fiber is faulty Check whether the optical fiber is connected normally to the appropriate interface The received optical power at the ONU exceeds the normal power range the optical power is too low or overload The ONU optical module is aged or damaged Check if the equipment at the central office end is operating normally The network interface indicator LED is extinguished Check whether the network cable is damaged or incorrectly connected Check whether the wiring color coding scheme of the network cable is incorrect If yes replace the original network cable with a standard CAT 5 twisted pair ne
7. mage the AN5506 01 As optical interfaces and fiber jumpers and cause them fail to function Connection diagram Optical splitter ON OFF Power Reset Figure 3 1 Connection diagram for optical fiber 3 3 2 Connecting Network Cable Cable and wire description The Ethernet interface of the AN5506 01 A is connected to the user s PC and the switch via network cables to access data service Connection procedures Plan the layout of the network cable Measure the distance from the AN5506 01 A to the user terminal and choose the network cable with an appropriate length for connection uN 3 Product Installation Step 2 Step 3 Step 4 Secure the network cable and make the RJ 45 crystal head connectors at both ends of the cable Insert the crystal head at one end of the network cable into a LAN interface of the AN5506 01 A Insert the crystal head at the other end of the network cable into the Ethernet interface of the user s computer or the switch Note 1 The transmission distance of the network cable is shorter than 100m Therefore the network cable you prepare should not exceed 100m Note 2 The Ethernet interface of the AN5506 01 A supports the MDI MDIX self adaption You can use the straight through or cross over network cable for connection Figure 3 2 Connection diagram for network cables 3 Product Installation 3 3 3 Connecting Power Cable The AN5506 01 A uses a 2 conductor power ad
8. oncnnnnos 10 3 3 1 Connecting Optical Fiber Jumper 10 3 3 2 Connecting Network Cable 0 11 3 3 3 Connecting Power Cable oocococcccccccccccccncocncnno 13 3 4 Inspection after Installati0n ooccconconnconncornconcos 13 1 Product Description 1 1 Product Function The AN5506 01 A is a desktop GPON ONU used for the network connection of the FTTH equipment lt can provide data and multicast access services to meet the broadband access requirements families Below is the network diagram of the AN5506 01 A Internet AN5506 01 A Splitter AN5516 01 Figure 1 1 Network diagram of the AN5506 01 A As shown in Figure 1 1 the AN5506 01 A is used together with the AN5516 01 OLT They together make up a GPON system that provides a large capacity high reliability multi service access network The AN5506 01 A supports the following functions Uses GPON uplink that is compliant with ITU T G 984 series of standards Supports the configuration of Ethernet interface rates working modes MDI MDIX auto negotiation mode and PAUSE flow control Supports packet filtering and illegal message attack protection Provides performance statistics on all Ethernet lines u l Product Description Supports the DHCP Option82 to report the physical location information of the Ethernet interface Supports the IGMP Snooping protocol Supports L2 L3 wire spee
9. pment receives LED l optical signals Optical linking The equipment receives no signal status optical signal Ethernet ul The interface is connected to interface the user terminal without status data transmission indicator linking The interface is transmitting A sa O The interface is not connected to the user o terminal N OFF N ms OFF N a FF 2 Product Appearance 2 2 Rear Panel and Interface With all interfaces and buttons distributed on the rear panel the AN5506 01 A has a simple model that is convenient for use As shown in Figure 2 2 the interfaces and buttons from left to right are power switch power interface reset button Ethernet interface x1 and PON interface ON OFF Power Reset LAN Figure 2 2 Front view of the AN5506 01 A rear panel See Table 2 2 for descriptions of the interfaces and buttons on the AN5506 01 A Table 2 2 Description for the AN5506 01 A interfaces and buttons ON OFF Turns on or off the power to the 12V DC Power 2 conductor Connects supply jack power supply 2 conductor DC power jack adapter Reset Reset Button Resets the equipment LAN Ethernet RJ 45 Connects to the computer A PON Optical SC PC Connects to the optical 3 Product Installation 3 Product Installation 3 1 Preparation 3 1 1 Unpacking Check When unpacking the AN5506 01 A please check that all items on the list are present and not damaged If any item is missing or has been dam
10. tandards Client side Ethernet One RJ 45 interface Supports full dup l l lex or half duplex 10 100 1000 M MENACE ntenace bit s self adaption l 35mm X 129mm X 117mm height X width Mechanical Dimension X depth parameter Weight 3009 Power supply parameter Power consumption lt 5W parameter Operating l 5 C to 45C Environmental temperature parameter Storage 20 C to 70 C temperature 1 Product Description Type hem Desemption Environmental l 10 to 90 non condensing humidity 2 Product Appearance 2 Product Appearance 2 1 Front Panel and Indicator LEDs The AN5506 01 A has a streamline design with novel and fashionable appearance The LED indicators on the front panel show the operating status of the equipment thereby the users can learn about the status directly Figure 2 1 shows the front panel of the AN5506 01 A LAN LOS PON Power Figure 2 1 Front view of the AN5506 01 A front panel Table 2 1 shows the description for the AN5506 01 A indicator LEDs NN 2 Product Appearance Table 2 1 Description for the AN5506 01 A indicator LEDs Name Meaning Color Status Description Power status Green O The equipment is powered indicator on via the 2 conductor DC LED power supply The equipment is not meir Registration Green O The equipment is registered status bl to the GPON system indicator OFF The equipment is not LED registered to the GPON system O indicator The equi
11. twork cable Check if the network cable length exceeds the allowed range FiberHome Telecommunication Technologies Co Ltd Tel 86 27 8769 1549 Address No 5 Dongxin Rd Hongshan Dist Fax 86 27 8769 1755 Wuhan China Website www fiberhomegroup com Zip code 430073
12. without high temperatures or direct sunlight to protect the equipment and its components from overheating which can result in damage Avoid moisture dampness and water damage Equipment exposed to water cannot work normally and can be extremely hazardous due to shorting Do not lay this equipment on an unsteady base Packing List When unpacking the AN5506 01 A please check that all items in the packing list below are present AN5506 01 A Conformity certificate Document bag DC power adapter with two Contains an AN5506 01 A GPON Optical Network Unit User Manual with the 2 conductor DC pow conductors RJ45 crystal head Mount to wall screw er adapter For securing the equipment on the wall Number Ea The AN5506 01 A is equipped 1 Contents 1 Product Description an 1 TT Product FUNGUO en 1 Pao ee Soe ee acne cesar eels 2 1 3 Technical Specification o cooccocccocncocnconoconiooncornnarnnnnos 2 2 Product Appearance une 5 2 1 Front Panel and Indicator LEDS oooocccoccccccccccnnncnnnnnonno 5 2 2 Rear Panel and Interface 2202202022020 nenn nnnn een T 3 Product Installation marnan 8 SPENN ieee 8 3 1 1 Unpacking Check occooccccccccocccconococococonocnonanicanonos 8 3 1 2 Installation PrecautiON ooccoocccocncoccconcncnoncnannnnnnnos 8 3 2 Equipment Mounting une 9 3 3 Cable and Wire Connection oocccocccccncnconincnncoconccon
Download Pdf Manuals
Related Search