F1 Small.pub - Ray Allen Manufacturing
Contents
1. 1 Powering On Your Remote Conitrol Pager RCP NOTE THE HUD MUST BE POWERED ON BEFORE PROCEEDING BE SURE THE REMOTE CONTROL PAGER RCP HAS BEEN FULLY CHARGED PRIOR TO ITS FIRST USE To turn on the RCP press and hold the ON OFF button release the button when the display begins to respond The RCP will go through a short diag nostic routine before making two short vibrations signaling connection with the System For Reference Only Actual Display size 80 X 1 25 inches RCP Display Properties Features Exclusive to Ray Allen Sensor 1 amp 2 Two Independent Temperature Readings Displays real time temperature from inside the vehicle Left Vertical Bar Signal Strength Between RCP and Vehicle Provides instant verification of signal integrity and strength Right Vertical Bar RCP Battery Charge Level Be assured you have the power for communication and to take action System Condition Deploy amp Heat Temp Systems Functioning Bold D amp H verify these systems are online and ready to respond System Status SYS OK The RCP and the vehicle Control POD are 100 all systems go MUTE Jo MUTE the RCP beeper When MUTED the vibration alert will still function to inform you of HEAT TEMP ALERT SYSTEM activation and other features BL PWR Backlight Power Press once to turn on the Backlight remains lit approximately 15 seconds then returns to normal Press and hold to Power Off the RCP Deployment Acknowledg2. RAY ALLEN PROFESSIONAL K 9 EQUIPMENT RAY ALLEN 7 F TACTICAL K9 DEPLOYMENT WITH TEMP ALERT D PAGE USER S MANUAL system Serial No TABLE OF CONTENTS SECTION System Features Charging the Remote Control Pager Starting Your System Accessing System Menu Programming Door Opener Programming Door Opener Window Drop Programming Heat Temp Alert Function Becoming Familiar w Interactive Intelligent Remote Powering On Your Remote Control Pager High Temperature Alert Screens amp Signals Vehicle Power Monitor Additional Features amp Information Remote Control Pager Notifications Product Care amp Service Warranty Disclaimer PAGE 10 11 13 14 15 16 17 18 19 RAY ALLEN F Tactical Deployment System With Temp Alert and Pager Features Heads Up Display HUD In Vehicle Independent Temperature Read Outs Displays System Status bold D K9 Deploy Ready bold H Heat Temp Alert Ready and SYS Ok Fully User Programmable Non Volatile Memory System retains your programmed settings if disconnected from vehicle battery Fan Control Built Right In Off Low Med High Plug to recharge Remote Control Pager wire pig tail included Interactive Intelligent Remote Control Pager RCP No Larger Then a Typical Pager K9 Deployment at the Touch of a Button Will Only Function with Vehicle in Park or Neutral if Neutral Safety Function Enabled Independent Temperature
3. simply press the button on the back of the Remote Control Pager NOTE THE DEPLOY K9 FUNCTION OPERATES ANY TIME THE SYSTEM IS TURNED ON AND THE VEHICLE IS IN PARK OR NEUTRAL OR AT ALL TIMES IF THE NEUTRAL SAFETY FEATURE WAS BYPASSED THIS FUNCTION IS NOT AFFECTED BY THE HEAT TEMP ALERT DELAY Programming Temp Alert Function RAY ALLEN F series a ZL In the SETUP Menu place the cursor on HEAT TEMP ALERT then press the SELECT button one 1 time RAY ALLEN F series By manipulating the UP DN SELECT XIT buttons as you did before the HEAT TEMP ALERT menu allows you to Turn on off the HEAT TEMP ALERT SYSTEM Select TEMPERATURE MODE F Fahrenheit or C Celsius Select the TEMPERATURE at which you wish the system to ALERT 70 99 F or 21 37 C Select the ALERT DELAY This feature prevents the Temp Alert System from acti vating when the vehicle is first started and the air condi tioning hasn t yet cooled the interior of the vehicle one 1 to ten 10 minutes selectable NOTE THE DEPLOY K9 FUNCTION OPERATES ANY TIME THE TEM IS TURNED ON THIS FUNCTION IS NOT AFFECTED BY THE TEMP ALERT DELAY NOTE FOR INFORMATION REGARDING THE ADVANCED MENU PLEASE SEE THE INSTALLATION MANUAL 10 Becoming Familiar With the Interactive Intelligent Remote Control Pager Front Back The front of the Remote Control Pager RCP houses the Interactive Display as well as the MUTE ON OFF buttons The back
4. turned off when charging NOTE IF THE REMOTE CONTROL BATTERY IS COMPLETELY DEAD IT MAY TAKE A FEW MINUTES BEFORE THE CHARGING SEQUENCE BEGINS NOTE WE HAVE PROVIDED YOU WITH A LONG LIFE REMOTE CONTROL BAT TERY DEPENDING ON TEMPERATURE IT CAN TAKE OVER 2 HOURS TO FULLY CHARGE THIS DEVICE FOR YOUR CONVENIENCE THE REMOTE CON TROL PAGER IS PROTECTED BY OVER CHARGE CIRCUITRY THEREFORE IT CAN REMAIN ON THE CHARGER FOR LONG PERIODS OF TIME WITHOUT FEAR OF BATTERY DAMAGE Starting Your System To Power up the system hold down the center button located on the Heads Up Display HUD Release the button when the LCD changes The system will perform a complete self diagnostic and you will see the following on the display Note that Serial Number POD SN appears here System Check displays events taking place Model and Version are displayed throughout diagnostic routine Starting Your System cont Once the diagnostic is complete the HUD will show displays similar to this Initial Display Default Delay 1 Minute Display After 1 Minute Delay Ready to Go After allowing for the 1 minute delay default the display will show two independent temperature readings a bold D K9 Deploy Ready a bold H Heat Temp Alert Ready and SYS OK Along the bottom are BL Backlight SET PWR menu access and power on off and FAN 0 OFF 1 LOW 2 MED 3 HIGH NOTE THE DEPLOY K9 FUNCTION OPERATES ANY TIME THE SYSTEM
5. IO FREQUENCY RF DEVICE THE ABILITY OF THE RF SIGNAL TO PENETRATE CERTAIN MATERIALS VARIES CELL PHONE AND PAGER SIGNALS FOR EXAMPLE DIMINISH GREATLY WHEN YOU ENTER BUILDINGS CONSTRUCTED WITH STEEL SUPER STRUCTURES AND METAL BUILDINGS IN GENERAL THESE SAME BUILDING STRUCTURES WILL AFFECT THIS SYSTEM S REMOTE SIGNAL LINE OF SIGHT READINGS TAKEN BY GPS HAVE SHOWN THE RF SIG NAL WILL WORK IN EXCESS OF 4 OF A MILE THIS RF SIGNAL HAS BEEN OPTIMIZED TO PROVIDE THE BEST POSSIBLE SIGNAL STRENGTH AND QUALITY HOWEVER SOME STRUCTURES AND MATERIALS WILL STILL ADVERSELY AFFECT THIS SIGNAL 15 Notifications From The Interactive Intelligent Remote Pager Displayed Message Event Description Audible Tactile Feed back 16 Product Care and Service Your system has been designed to give years of trouble free use Great effort was given to the selection of the highest quality components and fixtures Following are tips and suggestions that will help keep your sys tem fully functional Heads Up Display The Heads Up Display HUD can be cleaned with a soft moist cloth Do not use abrasive cleansers as they can damage the LCD panel and the housing Your HUD requires no additional user maintenance Interactive Intelligent Remote Control Pager Your Remote Control Pager RCP is designed to be carried on a law enforcement duty belt Included with your system is a custom belt hol ster that is engineered to offer durability ease of use a
6. IS TURNED ON AND THE VEHICLE IS IN PARK OR NEUTRAL THIS FUNCTION IS NOT AFFECTED BY THE HEAT TEMP ALERT DELAY Adjusting the Backlight To turn on and adjust the display backlight BL press the left button once to activate There are three 3 levels of backlight adjustment 1 2 or 3 BL 0 is off Built In Fan Control If you have chosen to integrate a fan with your system it is controlled by pressing the right button on the HUD There are three 3 speed adjust ments available for your K9 s comfort 1 LOW 2 MED 3 HIGH 0 is OFF Important Information Your system uses non volatile memory That means even if power is lost for long periods of time your user programmed settings will be re tained This is an especially handy feature should your vehicle need to have the car battery disconnected during maintenance NoTE YOUR SYSTEM IS POWERED BY DIRECT CONNECTION TO THE VEHICLE BAT TERY AND WILL REMAIN ON AND FUNCTIONING EVEN WHEN THE VEHICLE IS TURNED OFF THEREFORE WHEN YOUR VEHICLE IS NOT IN SERVICE AND OR YOU NO LONGER REQUIRE THIS SYSTEM TO FUNCTION YOU MUST MANUALLY TURN THE SYSTEM OFF PRESS AND HOLD THE CENTER BUTTON OF THE HUD Accessing The System Menu Access the particular system you wish to program by first pressing the center SET PWR button on the HUD one 1 time do not hold the but ton down This brings you to the first level of your System Menu SETUP RAYALLEN F series Pressing SE
7. LECT one 1 time to access the DOOR OPENER menu There are two 2 options in this menu EXCLUSIVE PROGRAMMABLE FEATURE The system has the ability to roll down either or both of the rear windows when using Remote Control Deployment This is espe cially handy for situations where a secondary suspect is blocking the deployment door NOTE TO TAKE FULL ADVANTAGE OF THIS FEATURE THE DEPLOYMENT DOOR MUST NOT HAVE A WINDOW GUARD INSTALLED Turning Door Opener On Off RAY ALLEN F series With the curser on DOOR OPENER press the SELECT button one 1 time The curser will move to the right as shown above and highlight the on off feature Press the DN or UP button to toggle either ON or OFF When the desired selection is displayed press and hold the SE LECT button until the curser moves back to DOOR OPENER as shown below Rav ALLEN PROGRAM THE WINDOW DROP Press the DN button to move the curser to WINDOW DROP Press the SELECT button one 1 time to move the curser to the right The sys tem allows four 4 WINDOW DROP options when used with DOOR OPENER These options are OFF neither window will drop when the K9 is deployed LEFT RIGHT or BOTH and will scroll using the UP or DN buttons When the desired selection is displayed press and hold the SELECT button until the curser moves back to the left To exit DOOR OPENER menu press and hold the SELECT button to return to the SETUP menu To DEPLOY your K9
8. Read Outs Real Time Reset Capability from Remote Control In the event of a HEAT TEMP or VEHICLE POWER Alert Signal Strength Indicator Bar Battery Charge Level Indicator Bar Out of Range Text Warning Deployment confirmation remote will beep twice and vibrate once to acknowledge Deployment activation Backlit Display Built In Pager Tone and Vibration for HEAT TEMP or VEHICLE POWER Alert Tone Mute Capability Fully Rechargeable Wall plug Charger Included RCP can also be charged from the HUD wire pigtail included Custom Belt Mounted Remote Control Holster Included Control POD Brain box of the system in a small case Can be easily mounted anywhere in your vehicle Positive lock wire harnesses no more loose wires Charging the Remote Control Pager After unpacking the System we recommend that the installer im mediately charge the Remote Control Pager If this has not been done the procedure for charging the Remote is 1 Locate the Remote Control and Remote Control Charger 2 Plug the Remote Control Charger into a 110v 60hz receptacle standard wall plug 3 Plug the Remote Control Charger into the charging port on the side of the Remote Control 4 The message CHARGING BATTERY will appear on the LCD screen of the Remote Control Pager along with a charging progress meter 5 When fully charged the CHARGING BATTERY message will no longer be displayed 6 The Remote Control Pager does not need to be
9. ement The Remote will beep twice and vibrate once to confirm Deployment activation Additional Exclusive Feature The RCP will inform you when you are out of range of the vehicle by display ing an OUT OF RANGE message on the LCD When you come back into range the display will once again show system information The HEAT TEMP ALERT System in the vehicle will function normally regardless of this signal strength 12 High Temperature Alert Screens and Signals RAY ALTEN F SERIES The above message is displayed on the HUD during a high temperature ALERT To stop the ALERT press the RESET button This will put the system into Standby Mode for a period of time equal to the ALERT DE LAY you programmed into your system NOTE THE RAY ALLEN F TACTICAL DEPLOYMENT WITH TEMP ALERT SYS TEM AND PAGER WILL NOT LOWER THE WINDOWS OR ACTUATE THE VEHICLE LIGHTS AND HORN THE TEMP ALERT SYSTEM WILL TURN ON THE OP TIONAL FAN IF THE FAN IS INTEGRATED INTO THE SYSTEM Your RCP will alert you of a high temperature ALERT in a variety of ways When the RCP first receives the alert it will alternately vibrate and beep while the display shows ALERT HIGH TEMP ALERT You can reset the system remotely by pushing the RESET ON OFF button once The system will enter Standby Mode as noted above This allows you to return to your vehicle and resolve the issue while silenc ing the ALERT on the RCP You may also silence the beeper function of
10. ion of this unit and is voided if the F Series System is removed from the originally installed vehicle and installed into another vehicle Warranty service requests are to be reported by phone to Ray Allen at 800 444 0404 or sent in writing via e mail to Fseries rayallen com Requests require the serial of the System and original sales order number to be processed To activate your warranty register your product on the Ray Allen web site Go to the following link to process your registration www rayallen com fseries register 18 Disclaimer Ray Allen Manufacturing LLC can at its discretion and without preju dice make improvements to these products at any time These im provements may or may not be made available to previously purchased products This product is designed for sale and use within the United States of America and its territories Ray Allen Manufacturing LLC will assume no liability or responsibility for any use or installation of this system out side of the USA Such use is the sole responsibility of the purchaser This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may ca
11. nd comfort when carrying the RCP The RCP contains a high quality rechargeable memory free battery When connected to the charger the LCD display will read CHARGING BATTERY If the battery is completely discharged it can take a minute or more for the display to show the CHARGING BATTERY message When fully charged the CHARGING BATTERY message will no longer be displayed Your RCP can be cleaned with a soft moist cloth Do not use abrasive cleaners as they can damage the LCD panel and the case Do not sub merge the RCP in water However if the RCP does become immersed in water turn it off immediately Allow the RCP to completely dry before attempting to turn it on again 17 Warranty Two Year Warranty Ray Allen Manufacturing LLC guarantees the purchaser that this F Se ries System will perform without defect in materials and workmanship for a period of two years from date of purchase Ray Allen will replace or repair defective materials at its discretion Exclusions to this warranty include but are not limited to acts of God or nature vehicle accidents product misuse or alteration without the ex plicit direction of Ray Allen or improper installation Warranty does not include cost of removal installation labor or any other cost incurred by purchaser Ray Allen Manufacturing LLC assumes no responsibility or liability for installation use or misuse of the F Series System This warranty is valid for the original installat
12. of the RCP houses the recessed Deploy K 9 remote control deployment button Located on the side is the RCP charging port not shown The RCP is designed to be carried on a law enforcement duty belt us ing the supplied custom holster The RCP should be carried with the DEPLOY K 9 Button facing outward away from the user The supplied holster has a molded hole that will align perfectly with the DEPLOY K 9 button The DEPLOY K 9 Button is recessed to help eliminate the accidental deployment of the K 9 To activate this function you must push the tip of your finger into the hole on the holster or into the depression on the back of the remote if the unit has been removed from the holster There are two ways you can recharge your RCP This system includes a wall plug charger for this purpose But there also is a pigtail wire in cluded with the system that allows you to connect your RCP with the HUD for the purpose of charging the Remote at any time your sys tem does not need to be turned on Just insert one end of this pigtail into the plug on the bottom of the HUD just below the left button and insert the other end into the charger port on the side of the RCP Your Remote does not need to be turned off to be recharged NOTE THE HOLSTER HAS BEEN CONSTRUCTED OF A SPECIAL POLYMER THAT CAN BE CUT THIS WILL ALLOW YOU TO ENLARGE THE HOLE IF NEC ESSARY TO ACCOMMODATE LARGER FINGERS TO ACCESS THE DEPLOY K 9 BUTTON THROUGH THE HOLSTER
13. ormation About Your TEMP ALERT SYSTEM Should a HIGH TEMP ALERT occur your system is designed to be as purpose based as possible The following demonstrates features built into your system If your system informs you of a HIGH TEMP ALERT and you choose to RESET the system remotely from the RCP the system will enter Standby Mode for a period of time equal to the ALERT DELAY you have programmed If during this Standby Period the interior tempera ture of the vehicle drops below the ALERT TEMP setting the system will reset and return to normal operation at the end of the Standby Pe riod NOTE IF YOU HAVE ADDED AN OPTIONAL FAN TO THE SYSTEM IT WILL CONTINUE TO RUN AT HIGH SPEED UNTIL YOU MANUALLY CHANGE THE FAN SPEED ON THE HUD If the temperature does not drop below the ALERT TEMP setting you have programmed the system will again ALERT you when the Standby Period expires NOTE IF YOU MUTE THE RCP YOU WILL BE NOTIFIED ONLY BY THE VIBRATION FUNCTION AND THE ALERT SCREEN DISPLAY ON THE RE MOTE BUT THE VEHICLE WILL CONTINUE TO REACT NORMALLY lf you are OUT OF RANGE and do not receive a HIGH TEMP ALERT on your RCP your in vehicle system will react as if it was still in contact with the RCP The moment you are OUT OF RANGE from the vehicle the RCP will warn you OUT OF RANGE will appear on the RCP display When you come back into range the RCP again will display system informa tion NOTE AS WITH ANY RAD
14. the RCP by pressing the MUTE button 13 Vehicle Power Monitor The above message is displayed on the HUD during a VEHICLE LOW VOLT AGE condition This ALERT is caused by the battery voltage falling below the recommended level for normal operation The voltage threshold is hard coded into the system and cannot be altered The cause of a VEHICLE POWER ALERT can be a stalled engine over taxing the vehicle s electrical system a faulty battery or alternator and or many other issues The system will send an immediate signal to the RCP alerting you remotely of the condition To stop the ALERT press the RESET button This will put the system into Standby Mode for a period of time equal to the ALERT DELAY you programmed into your system NOTE THE RAY ALLEN F TACTICAL DEPLOYMENT TEMP ALERT SYSTEM WITH PAGER WILL NOT ACTUATE THE VEHICLE LIGHTS AND HORN OR TURN ON THE OP TIONAL FAN IN THE EVENT OF A VEHICLE POWER ALERT Your RCP will alert you of a VEHICLE POWER condition in the same manner as a HIGH TEMP ALERT The RCP will alternately vibrate and beep while the display shows ALERT VEHICLE POWER You can reset the system re motely by pushing the RESET ON OFF button once The SYSTEM will enter Standby Mode This allows you to return to your vehicle and resolve the issue while silencing the ALERT on the RCP You may also silence the beeper function of the RCP by pressing the MUTE button 14 Additional Features and Inf
15. use harmful interference to radio communications However there is no guarantee that Interference will not occur in a particular installation If this equipment does cause harmful Interference to radio or television reception which can he de termined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna lIncrease the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult an experienced technician for help This device complies with part 15 of the FCC Rules Operation is sub ject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Caution changes or modifications not expressly approved by Ray Allen Manufacturing LLC could void the user s authority to operate the equip ment 19 RAY ALLEN PROFESSIONAL K 9 EQUIPMENT For More Information Contact Ray Allen Manufacturing LLC 975 Ford Street Colorado Springs CO 80915 800 444 0404 719 380 9730 Fax www rayallen com fseries rayallen com
Download Pdf Manuals
Related Search