Quick Start Guide Wireless Light Control
Contents
1. Relaxing 8 The alarm event is activated after Alarm Timer creation per default and can be deactivated by pressing the button Disable op 2 g g OU iz 9 Confirm all changes by pressing Apply Scene On Group On Group Off Scene Repeat Schedule enabled Disable Cancel Wireless Light Controli Groups Schedules Devices 10 Now the created alarm event is visible in the schedules menu Gateway time is 12 19 Relaxing 12 00 Mo We Fr dresden elektronik ingenieurtechnik gmbh 10 2015 Page 9 of 15 Wireless Light Control dresden elektronik Quick Start Guide Set up the timer event The timer event defines a period of time after which the lights will perform a defined action This example describes the _ timer based activation of all lights of a group Wake U Wake Up 1 Assign a name for the event 2 Select the timer event by pressing the button Timer 3 Define the period of time in hours and l _ in min 4 The timer should activate all lights of a z selected group Therefore press button Group On 5 Choose the group by lt 6 The lights of the selected group should not dim on rapidly Instead they should dim on with a defined fading time The Group Living Room duration can be configured in minutes and seconds by pressing the button lt Src 155 7 The lights of the selected group should not exceed a defined brightness level The Level can be configured between Level 602. 10 and 100 by pressing the button Alarm Timer Scene On GroupOn Group Off 8 The timer event is activated after creation per default and can be deactivated by pressing the button Disable 9 Confirm all changes by pressing Apply Schedule enabled Disable Cancel Wireless Light Controli Groups Schedules Devices 10 Now the created timer event is visible in the schedules menu The selected period Gateway time is 16 18 of time will be displayed and decrease every minute Relaxing 12 00 Mo We Fr Wake U g p aN in 30 min dresden elektronik ingenieurtechnik gmbh 10 2015 Page 10 of 15 Wireless Light Control dresden elektronik Quick Start Guide Adding a ZigBee switch The WebApp supports the adding and configuring of one or more ZigBee switches like the Philips Hue Tap Note Philips Hue Tap will be supported since gateway version 2 02 05 1 Press the button Connect a new Device Wireless Light Control Groups Schedules Devices in the menu Devices Connect a new Device Done Connect a new Device 2 Follow the instructions and press the button Search now pena ae 3 Press the displayed Tap button for at 2 Then hold Tap button for 10 seconds least 10 seconds and then release it Search now Done 4 Now the WebApp is seacrhing for the ZigBee switch Connect a new Device Connect a Hue Tap 1 Press Search now 2 Then hold Tap button for 10 seconds Searching for
3. new devices 8 5 A short status report will appear when the ZigBee switch is connected successfully Connect a Hue Tap to the network 1 Press Search now 2 Then hold Tap button for 10 seconds Connect a new Device Ok Found a new device Search now Done 6 The connected ZigBee switch appears in Wireless Light Control Groups Schedules Devices the Devices menu and can be configured by pressing the button G zePswten Connect a new Device Done dresden elektronik ingenieurtechnik gmbh 10 2015 Page 11 of 15 dresden elektronik Wireless Light Control Quick Start Guide Configuring a ZigBee switch Every tap button of the connected Philips Hue Wireless Light Controi Groups Schedules Devices Tap can be assigned with the following functions All lights on All lights off a Group on Call Scene Group off Call Scene Call scene Call Scene RGB Lights Red v Delete Apply Cancel Confirm the settings with Apply System settings The available system settings are displayed in default mode as well as in advanced mode Several system settings can be configured Settings Display the version number of the gateway deCONZ Modify the gateway name Choose the time format between 24h and 12h AM PM euler Vern Change the WebApp login user name and sepsis aE RPI password Default name is delight and Time Format 24h PEE E password delight Press Unlock Gateway to allo
4. Light 16 Ging Pa Switch on off complete group off per button Call up scene editor Set up color and brightness The RGB color setup will be supported by the FLS PP Ip with connected RGB W illuminant The white channel W can be controlled separately Smartphone view Name of the light Desktop Tablet vie mE changeable Wireless Light conoi cous Actual setup Saturation Color Temp White Brightness White channel Sat 78 done Sat dresden elektronik ingenieurtechnik gmbh 10 2015 Page 5 of 15 Wireless Light Control dresden elektronik Quick Start Guide Set up color temperature The CW WW color temperature will be supported by the FLS H Ip with connected cold white warm white illuminant Smartphone view Light 16 Name of 3 i the light Desktop Tablet view changeable Wireless Light cono cous Actual setup Color temperature Color Temp Temp 53 done Temp Create scenes By means of scenes complex light settings can be stored and simply be recalled later on at touch of a button 1 Set up lights within the group as desired by clicking on the sign f V oor 2 Press button in the group view Li ue ROOM s0 Light 24 ae 10 Light 16 Press button Create Scene Assign a name Relax I Press button Create to save the actual settings the scene Specify a Scene Name dresden
5. Open Network The advanced system settings allow further settings epee The Duration defines the network open time ose Networ pen the network for 1 minute and allow other ZigBee devices to join the z at which is selectable between 1 minute and 4 Duration The duration the network remains open m i n utes The OTAU Server activates automatic firmware updates of all network devices by dresden elektronik The Channel defines the actual ZigBee channel selectable by 11 15 20 and 25 Changing of the channel can take up to 10 seconds Otau Server Allow the gateway to update ZigBee devices automatically Change the ZigBee channel It can take up to 10 Channel seconds until all devices have completed the channel change Apply Done Software Updates To benefit from the ongoing development of the dresden elektronik Wireless Light Control application the gateway will automatically check for updates If there is a new gateway update available a corresponding message in the WebApp will appear The installation of a gateway update runs only after an explicit acceptance The update procedure may last some minutes depending on the Internet connection and size of the update Note Do not interrupt the gateway from power supply during the update process The SD card software image can be damaged and make the gateway unusable If the option OTAU Server is activated all lights will be automatically updated This takes pla
6. Wireless Light Control dresden elektronik Quick Start Guide This guide describes how to get started using components of dresden elektronik Wireless Light Control solution to run a demo application of a wireless light control network For example you already have the StarterKit Wireless Light Control or the RaspBee Gateway or you bought the necessary components separately Components StarterKit Wireless RaspBee Light Control Gateway Raspberry Pi Model B y V RaspBee premium y V Power supply unit with Micro USB plug NI N SD Card with Raspbian Linux Distribution V N Commercial WiFi Router Ethernet cable y Wireless electronic ballast s FLS 2x FLS PP Ip appropriate illuminant s 2x Test LED Strip RGB Power supply unit s for FLS Control device PC Smartphone Tablet with browser Note Raspberry Pi Modell B and Raspberry Pi 2 Modell B can also be used Setup gateway 1 Attach RaspBee on Raspberry Pi attach on extension header at the outer edge do not attach displaced 2 Insert SD card 3 Connect to router via Ethernet cable 4 Establish power supply use micro USB connector beside SD card slot 5 Initially the LEDs on the RaspBee blink green for a short time and then turn continuously red Wait for the booting routine takes approx 1 minute SD Card Power Supply If you separately purchased the components Raspberry Pi and or RaspBee basic you have to install t
7. ce in the background while controlling the system is still possible The actual state will be displayed in the WebApp main menu When the update transfer is completed the firmware is installed automatically During this process the light will not react on control commands for about one minute After the automatic restart the light is available as usual All settings like color brightness and scenes will be maintained Note If the update process of the lights will be interrupted by a power cut the update process will be started again automatically from beginning after power on If several update processes will fail next to another the light takes the internal working delivery firmware automatically dresden elektronik ingenieurtechnik gmbh 10 2015 Page 13 of 15 Wireless Light Control StarterKit dresden elektronik e Quick Start Guide Reset the light to factory settings Resetting the light is not necessary during normal operation A reset is required if lights shall join a new network The reset can be done in two different ways described below Reset via Touchlink If light and gateway can be moved within a range of less than 50 cm of each other a Touchlink Reset can be performed Scan for Devices e The devices need to be close 50 cm to the gateway e Use reset button to reset a device to factory new state Goto the menu Settings in the category After reset devices can rejoin any network Reset Devices via Touchlink and click the Yo
8. elektronik ingenieurtechnik gmbh 10 2015 Page 6 of 15 Wireless Light Control dresden elektronik Quick Start Guide 6 Get back to the main screen by pressing Wireless Light Control Groups Schedules Devices Scenes button Done Scenes Click on store to save the current state of the group to a scene MoE Only lights which are currently powered on will be affected Create Scene Done 7 The scene will be displayed next to the button on off and can be called on click Living Room Light 24 9 80 Light 16 On Modify and delete scenes Stored scene settings can also be modified or deleted 1 Set up lights within the group as desired by clicking on the sign 2 Press button in the group view to get to the scene editor Living Room 0 Light 24 s0 Light 16 Wireless Light Contr Groups Schedules Devices Scenes 3 Click button Store next to the desired scene Scenes Using Delete the scenes can be deleted Click on store to save the current state of the group to a scene HG Only lights which are currently powered on will be affected Create Scene Done dresden elektronik ingenieurtechnik gmbh 10 2015 Page 7 of 15 Wireless Light Control dresden elektronik Quick Start Guide Create time based events Creating editing and activating of time based events can be performed in the menu Schedules It is possible to create a timer or an alarm based event Note t
9. he gateway software deCONZ manually Please follow the RaspBee User Manual in this case See https www dresden elektronik de funktechnik solutions wireless light control starterkit See https www dresden elektronik de funktechnik solutions wireless light control raspbee gateway Smartphone charger PC or the like only limited suitable power supply 5 V 1 2 A required Download from www raspbian org gt Compatibility matrix http www dresden elektronik de funktechnik solutions wireless light control wireless ballasts See https www dresden elektronik de funktechnik solutions wireless light control wireless ballasts fls pp Ip Micro SD card necessary https www dresden elektronik de funktechnik service downloads documentation eID dam frontend push amp doclD 2145 dresden elektronik ingenieurtechnik gmbh 10 2015 Page 1 of 15 Wireless Light Control dresden elektronik e Quick Start Guide Hardware setup wireless electronic ballasts FLS PP Ip Attention This hardware setup is based on the example of the FLS PP Ip it could vary between other wireless electronic ballasts from dresden elektronik Please look at the respective product flyer to connect your acquired FLS correctly To wire the FLS PP lp use conductor with cross section of 0 2 0 75 mm AWG24 18 Dismantle the cable 6 7 mm Attention Insert remove fine stranded conductors by lightly pressing on push button with a small screwdriver or
10. ime based events will be supported from gateway version 2 00 00 1 Open the menu Schedules Wireless Light Control Groups Schedules Devices 2 Press the button Create Schedule Sey ane Ones Devices Create Schedule Done Note All created events are based on the system time of the gateway The time of the user device like tablet or aed smartphone is not relevant The gateway system time can be changed in the system settings Set up the alarm event The alarm based event defines a time on which the lights will perform a defined action This example describes the activation of an larm vent alarm based event New Schedule A 1 Assign a name for the event 2 Select the alarm based event by button Alarm 3 Setting the alarm time in hours and minutes 4 The alarm should activate a defined scene Therefore select the button Scene On 5 Choose the scene by button Alarm Timer On 12 iz E 00 D Scene On GroupOn Group Off Scene None Repeat Schedule enabled Disable Apply Cancel dresden elektronik ingenieurtechnik gmbh 10 2015 Page 8 of 15 Wireless Light Control dresden elektronik Quick Start Guide 6 Choose the scene Relax of the group a Living Room and confirm with Apply Choose the scene which will be activated Living Room Relax D 7 The event takes place on the defined time at defined weekdays Select the days by clicking the buttons Mo Tu We Th Fr Sa and So
11. lluminants don t have a _ special indicator Ime Eh 24h z The format of the time displayed 5 The network will close automatically after one u Ghame e Logi Password m j nute Unlock the gateway for 60 seconds to allow 3rd party apps to register Unlock Gateway themself to the gateway After the registration they can access the gateway even if it s locked Note Do not use backward and forward buttons of your web browser Use the buttons of the WebApp instead Apply Done Open the network for 1 minute and allow other ZigBee devices to join the network Info Network open Check the main page if new Lights where found 57 seconds left Close Network VNSRSSIGINI CONC EEN eee non 6 The new light will be displayed Press button eae i Pon hae we ee Name Model Light 24 FLS PP3 7 Choose a group which the light should be Add to Group assigned to 8 Ifthe group does not exist press button Light name Light 24 j Create Group Group z 9 Press Apply to complete the action et oan ee Create Group Wireless Light Control Groups Schedules Devices 10 The light appears in the chosen group Living Room 80 Light 24 On Off dresden elektronik ingenieurtechnik gmbh 10 2015 Page 3 of 15 Wireless Light Control dresden elektronik Quick Start Guide Grouping lights The lights can be combined to groups within a ZigBee network One light can be a part of several groups Lights can be added or removed from a
12. n existing Wireless Light Controli Groups Schedules Devices S roup in the menu Groups eee a j Groups ae Press Create Group to create a group of lights eE EE UPE ane ha a ines Press Edit Members to define the lights of an I existing group Edit Members Delete Create Group Done Sse COCs MEER Press button Edit Members to get back to group configuration Group Living Room Activate the lights in the chosen group by setting the check box EI Light 16 3 dresden elektronik 020 201000A0 Deactivate the lights in the chosen group by unchecking the box Light 17 3 dresden elektronik 020C 201000A0 E Light 18 3 dresden elektronik 020C 201000A0 Grayed lights are actually not available because Light 19 3 dresden elektronik 020C 201000A0 of interrupted power supply or they are not a part Light 21 3 dresden elektronik St of the network Inactive lights will dissappear from the group configuration after gateway restart Light 22 3 dresden elektronik 020C 201000A0 Light 23 3 dresden elektronik 020C 201000A0 Press Apply to complete the process Apply Done dresden elektronik ingenieurtechnik gmbh 10 2015 Page 4 of 15 Wireless Light Control dresden elektronik Quick Start Guide Controlling lights living Room o 4 Configure color brightness saturation of the group Switch on off rae lights separately ia lt Configure color brightness l turation of individual lights per bulb symbol sa Wy 9
13. or the information provided being up to date correct and complete dresden elektronik ingenieurtechnik gmbh Phone 49 351 31850 0 Fax 10 Enno Heidebroek Str 12 wireless dresden elektronik de Contact 01237 Dresden Germany www dresden elektronik de dresden elektronik ingenieurtechnik gmbh 10 2015 Page 15 of 15
14. pen Don t use ferrules or tinned wires 1 Connect FLS PP Ip with LED strip 2 Connect LED Power Supply to both FLS PP lo Initially the illuminants shine monochromatic white 2 folololojojojo JR In gt FLS PP Ip 12 24V DC The combination of FLS PP Ip and illuminant will be referred to as light below Setup web application 1 Open a web browser on the control unit PC tablet needs access to the local network 2 Open the following address Internet connection necessary http www dresden elektronik de discover Click the gateway link there ey Foon with ts User delight 7 Password delight mes login lost password Create bookmark of gateway link for ease of use dresden elektronik ingenieurtechnik gmbh 10 2015 Page 2 of 15 Wireless Light Control dresden elektronik Quick Start Guide Add lights to wireless network The ZigBee wireless network is closed by default and has to be opened during setup temporarily so that new lights can join the network 1 Select menu Settings in the upper rig ht Wireless Light Controli Groups Schedules Devices Settings corner Groups Settings Schedules 2 Click on button Open Network The network Devices will remain open for 1 minute Settings 3 Click on button Done to get back to main Logout screen 4 Wait until the devices join the network o colored illuminants then shine green fae eae r monochromatic i
15. reless Light Control dresden elektronik Quick Start Guide Notes 1 Each light can be a member of up to 10 groups 2 Inthe user interface any number of groups can be created with each up to 16 scenes 3 A scene always describes the status of the complete group i e changing the scene affects all lights 4 Ifa light is powered off and on again its last settings are restored If settings per user interface have been changed meanwhile they are ineffective after switching on again 5 Not existing lights are displayed grayed out semi transparent in the user interface 6 Lights can only belong to one network but to several groups they rejoin it automatically after switching on again If a light shall be assigned to a new network it must be reset to factory settings first 7 For optimum accessibility of your lights we recommend that the gateway is powered on permanently After reboot the website may have to be loaded again Please see section Reset FLS to Factory Settings Please also note the Frequently Asked Questions which can be found on our website htto www dresden elektronik de funktechnik service support fag wireless light control L 1 2015 dresden elektronik ingenieurtechnik gmbh All rights reserved Other registered trademarks or terms and product names are the property of their respective owners All information contained herein is subject to change without notice No liability can be accepted or guarantee made f
16. ur gateway is on channel 15 and has the network id Oxab18 button Scan for Devices A progress bar indicates the process After the scan procedure has been completed a list of available devices within the range gets displayed Each light should be identified by clicking Done the blink button first before resetting it Observe the status of each operation at the bottom of the page If the target light is not listed try scanning again Click the button Reset to set back the light to factory settings Lights Name Address Channel Network Id RSSI blink Light 1 0x00212effff0058a2 15 0xdb18 31 Reset via power cycle sequence If gateway and lights are installed fixed the distance between them might be greater than 50 cm In this case the Touchlink Reset will not work Proceed with a power cycle sequence as follows 1 Power cycle 4 times within 2 to 20 seconds on time 2 When switching on for the fourth time illuminant blinks for 10 seconds 3 Wait until illuminant stops blinking 4 Switch on and off again 2 times after approximate 2 seconds the device begins to restore the factory settings duration approximate 60 seconds in this time the light is off Afterwards the light is operative again and can be added to a network 4x off on a 2X off on 7 Blinking ai UU Uy aoso UU Uy off 10 seconds on for min 2 seconds on for min 2 seconds dresden elektronik ingenieurtechnik gmbh 10 2015 Page 14 of 15 Wi
17. w 3 party apps Re es eee to register themself to the gateway eae tar veld ana are tr Show Advanced Settings Change Password Change the Login Password Tao The advanced system settings allow further control Detailed specification for time and date Group Delay defines the time between two i d group commands Small values could Don ve EEE oon HEED oy overload the network Gateway Time nea SD EER cet cient caterime Internet Service allows the gateway to register on the dresden elektronik discovery webpage and check for updates Software Version Gateway Name Timezone Europe Berlin GMT 01 00 a The format of the time displayed Change Password Change the Login Password Unlock the gateway for 60 seconds to allow 3rd party apps to register Unlock Gateway themself to the gateway After the registration they can access the gateway even if it s locked Soop tey Delay between two group commands in milliseconds Internet Service Allow gateway discovery and checking for updates via internet 1 See http www dresden elektronik de discover dresden elektronik ingenieurtechnik gmbh 10 2015 Page 12 of 15 Wireless Light Control dresden elektronik Quick Start Guide Network settings The button Open Network opens the ZigBee network for new devices The network closes itself automatically after 1 minute Open the network for 1 minute and allow other ZigBee devices to join the network
Download Pdf Manuals
Related Search