Product Manual - Security Camera King
Contents
1. 3 26bit Wiegand RS232 Output Format 3 1 If you set the output to 26bit Wiegand RS232 format and press numeric keys on the keypad you can hear a beep sound with the yellow LED flashing which indicates PIN entry start Once you enter the PIN press ENT key to finish PIN entry The yellow LED will turn off indicating PIN entry is finished The reader will then send the PIN data to the controller 3 2 In the 26bit Wiegand RS232 output format a facility code is within the range of 0 to 255 and an ID PIN is in the range of 0 to 65535 If you do not finish your PIN entry with ENT key or if you do not press any key within 5 seconds the reader will make error beeps Beep Beep Beep Beep then clear the PIN data no output and return to the standby mode An ID PIN you can enter via the keypad is from 1 to 8 digits e g If you enter a 1 8 digit PIN D 1234ENT Wiegand 00001234 RS232 00001234 12345678ENT Wiegand 12345678 RS232 12345678 4 Burst RS232 Output Format 4 1 When you set output to Burst RS232 format and press numeric keys on the keypad you can hear a beep sound and the green LED turns on indicating PIN entry start 4 2 When you set output to Burst RS232 format PIN data sends 8bit Burst format if you press numeric keypad And if you enter lt ENT gt key with 1 to 8 digit of keypad PIN data sends RS232 format In case of RS232 output format if you do not finish PIN entry with ENT key and or if2. Do not use this product near water such as bath tub wash bowl kitchen sink laundry tub in a wet basement or swimming pool This product should be operated only from the type of power source indicated on the marking label If you are not sure of the type of power supplied to your installation site consult your dealer or local power company Never push objects of any kind into this product or through the cabinet slots as they may touch voltage points or short out parts that could result in fire or electric shock Never spill liquid of any kind on the product To reduce the risk of electric shock do not disassemble this product by yourself but take it to qualified service whenever service or repair is required Opening or removing the covers may expose you to dangerous voltages or other risks Also incorrect reassembly can cause electric shock when the unit is subsequently used Unplug this product from the Direct Current DC power source and refer to qualified service personnel under these conditions a When the power supply cord or plug is damaged or frayed b If liquid has been spilled on the product c If the product does not operate normally after following the operating instructions in this manual Adjust only those controls that are covered by the operating instructions in this manual Improper adjustment of other controls that are not covered by this manual may damage the unit and will often require extensive work by a
3. FOR ANY PERSONAL INJURY PROPERTY DAMAGE OR LOSS DIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES OR OTHER LOSS AND IDTECK S MAXIMUM LIABILITY SHALL NOT IN ANY CASE EXCEED THE PURCHASE PRICE OF THE PRODUCT To obtain repair or replacement under the terms of this warranty visit IDTECK s Website http www idteck com and place an online RMA request After an RMA code is issued return the product along with the authorization RMA code gt gt Warranty Period Product Category Warranty Period RF CARDS ACTIVE TYPE FINGERPRINT MODULE SENSOR RF READERS WITHOUT EPOXY POTTING STANDALONE CONTROLLERS CONTROL PANELS FINGERPRINT READERS RF READERS WITH EPOXY POTTING Lifetime RF CARDS PASSIVE TYPE 1 year 2 years ao i an P DY N 16 IDTECK Star RFK101 13 How to Make RMA Request After Sales Service To make the RMA request the product must be initially registered on IDTECK webpage Please attach the RMA request form on the product and send it to IDTECK RMA Center Please follow the instructions below 1 Please register the RMA request via IDTECK webpage www idteck com gt Support amp Download gt Online RMA gt RMA REQUEST Please refer to the IDTECK webpage for more details 2 RMA Code will be issued after the RMA Center reviews the RMA request form Fill out the A S request form included in the product package and attach it to the product using the aluminum
4. you do not press any keypad for 5 seconds clear PIN data no output and return to normal mode 10 IDTECK Star RFK101 5 LED Control You may change the behavior of the red green and yellow LEDs as follows To keep the red LED turned off connect the LED control in wire white with red stripe to the GND To keep the green LED turned on connect the LED control in wire yellow wire to the GND To keep the yellow LED turned on connect the LED control in wire white wire with blue stripe to the GND For more information please refer to 8 Wire Connection to Access Controller on Page 8 6 Beeper Control In normal operation the reader sounds one beep when it reads a proximity card However additional beeps can be sounded to improve indication for access status granted or denied by wiring blue wire of the beeper control input to system ground level The beeper will remain on as long as the blue wire is connected to system ground 7 Tamper Switch The RFK101has normal close NC type Tamper Switch When the unit is installed with wall mount the tamper switch output wires the gray wire COM and the white with green stripe wire NC will be short circuits When the unit is removed from the wall mount the tamper switch output wires will be open circuits 9 3 2 Advanced Operation Optional 1 Supervisory Signal This unit sends supervisory signal through reader s output for a preset time 11 IDTECK Star RFK101 1
5. 0 Output Format 10 1 26bit Wiegand output format 1 Data format Bit 1 Even parity of bit 2 bit 13 Bit 2 9 Facility code 000 255 Bit 10 25 ID number 00000 65 535 Bit 26 Odd parity of bit 14 bit 25 2 Timing diagram 5V OV 5V OV 10 2 4 8bit Burst output format for PIN 1 Data format 4bit Burst output format Keypads Binary Hexa Keypads Binary Hexa 0 0000 0 6 0110 6 1 0001 1 7 0111 7 2 0010 2 8 1000 8 3 0011 3 9 1001 9 4 0100 4 ESC 1010 A 5 0101 5 ENT 1011 B 12 IDTECK Star RFK101 8bit Burst output format Keypads Binary Hexa Keypads Binary Hexa 0 11110000 FO 6 10010110 96 1 11100001 E1 7 10000111 87 2 11010010 D2 8 01111000 78 3 11000011 C3 9 01101001 69 4 10110100 B4 ESC 01011010 5A 5 10100101 A5 ENT 01001011 4B 2 Timing diagram 5V OV 5V OV 13 IDTECX Star RFK101 10 3 RS 232 output format 1 Data format Baud rate 9600bps LSB MSB 15V 0 1 0 0 0 0 0 1 0 Space 0 8V 4 4 do hoi o ov Indeterminate Region EA Yd RR A A A A EE IA AP Mark 1 45V e 8 Data Bits 2 Stop Bits Start Bit P i lt Data packet corresponding to ASCII character A 2 Data structure DATA 8 Char END 0x03H LRC CARD output START 0X02H DATA
6. 1 8 Char END 0x03H LRC Keypad output START 0X02H 14 IDTECK Star RFK101 11 FCC Registration Information FCC Requirements Part 15 CAUTION Any changes or modifications in construction of this device which are not expressly approved by the responsible for compliance could void the user s authority to operate the equipment NOTE This device complies with Part 15 of the FCC rules Operation is subject to the following two conditions 1 This device may not cause harmful interface and 2 This device must accept any interference received including interference that may cause undesired operation This equipment has been tested and found to comply with the limits for a Class A Digital Device pursuant to Part 15 of the FCC rules These limits are designed to this equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the radio or television off and on the user is encouraged to try to correct interference by one or more of the following measures 1 Reorient or relocate the receiving antenna 2 Increase the separation between the equipment and receiver 3 Connect the e
7. Star RFK101 5 Specification IDK50 IMC 125 Up to 2 inches 5cm Passive Type Read Range IDC80 IDC170 Up to 4 inches 10cm Active Type IDA150 IDA200 Compatible Reading Time Card 30ms Power Current DC12V Max 150mA 2 Ports for External LED Control 1 Port for External Buzzer Control 3 Ports for External LED Control 1 Port for External Buzzer Control Card 26bit Wiegand and RS232 default Output Format Keypad 8bit burst default 26bit Wiegand selectable or 4bit burst selectable Default Input Port Optional Keypad 12 Key Numeric Keypad with Back Lighting LED Indicator 3 Array LED Indicators Red Green and Yellow Beeper Piezo Buzzer Operating Temperature 35 to 65 C 31 to 149 F Operating Humidity 10 to 90 relative humidity non condensing Color Dark Pearl Gray Polycarbonate 87mm x 100mm x 31mm Dimension W x H x T 3 4 x 3 94 x 1 22 190g 0 42Ibs Certification FCC CE MIC IDTECK Star RFK101 6 Installation 6 1 Use the provided Template on Page 18 to drill two 6 32 or M3 screw holes 3 3 8 38cm apart in vertical and one 1 2 hole at the center of these two holes If you have installed electric gang box then skip this step 6 2 Make sure that magnet is attached by magnet guide of wall mount 6 3 Using two 6 32 or M3 screws install wall mount to the wall 6 4 Insert 5 O rings to the wall mount as indicated then route the cable of the main unit throug
8. User s Manual Star RFK101 PIN amp Proximity Card Reader Star RFK101 AGRE IDTECK IDTECK Star RFK101 Table of Contents 1 Important Safety SUPA CUO UNS rata A LA AAN a SAE 3 a ta A a e da a e 3 IA a 4 4 Identifying Supplied Parts cccssesecsssesessessecsssesessesessesesssecsesecsucsesecsesacsesecsesessesesasseeaseeeseees 4 S Specifa AAA A Mamaia dau MA a NAA aa NN MAN 5 Ce MOS FeAl E RO 6 T Wire Color Table of the Reader A al laa eal A 7 8 Wire Connection to Access Controller 0 cesccsesessessestsssestssssstsseensesseessstsateatestesteatentenseteaens 8 AA A A a a Sle lla lea 9 10 Output STEORINVA ec E O spate ake 12 11 FCC Registration Information aii td tuners 15 12 Warranty Policy and Limitation of Liability 0 c ccescecsssesseseseseseeeseeesesceeeneieetseneseneess 16 13 How to Make RMA Request After Sales ServiCe ccccecessecsssesteeceesesseseseesteneneenessente 17 14 Template ota 18 IDTECK Star RFK101 1 Important Safety Instructions When using your PIN amp Proximity Card Reader basic safety precautions should always be followed to reduce the risk of fire electrical shock and injury to persons In addition the following should also be followed Read and understand all instructions Follow all warnings and instructions marked on the product Do not use liquid cleaners or aerosol cleaners Use a damp cloth for cleaning If necessary use mild soap
9. h the center hole and push the main unit to wall mount to lock the main unit and make sure that the main unit is locked with wall mount 6 32 hole 1 18 30mm o C 1 55 39 5mm O ring O ring 1 79 45 5mm 1 52 38 5mm 1 52 38 5mm IDTECK Star RFK101 7 Wire Color Table of the Reader rns JO gra cor 7 O o e A A AAA IDTECK Star RFK101 8 Wire Connection to Access Controller Access Controller Main Power 12V Star Power Ground GND RFK101 Wiegand Data 0 Greeni f i Wiegand Data1 O __ Tamper Switch NC White with Green stripe l Tamper Switch COM EER o Blue Buzzer Control LED Control Red White with red stripe LED Control Green LED Control Yellow PC RS 232 TX RS 232 GND Connection Parts Connection Method Connect DC 12V wire of Power to Red wire of RFK101 Main Power 12V Connect GND wire of Power to Black wire of RFK101 Connect Green wire of RFK101 to Wiegand DO input port of the Controller Wiegand Data Out Connect White wire of RFK101 to Wiegand D1 input port of the Controller If you want to control LEDs connect each LED Control wire Red Green LED Control In Yellow wire of RFK101 to GND of controller If you want to control the buzzer connect Blue wire of RFK101 to GND of Buzzer Control In nirole Connect to the COM port of the PC Connect pin 2 of the DB 9 connector RS 232 GND to the
10. purple wire connect the black wire of the 6 pin connector to pin 5 of the DB 9 connector IDTECK Star RFK101 9 Operation 9 1 Output Format Setting You can set output format of numeric input using output format setting switches Select one between 4 8 bit Burst and 26bit Weigand format depending on the controller type receiving control input Output format setting switches are on the back of RFK101 unit T LED Buzzer Control OFF WIK TX Power E Figure Position of Output Format Setting Switch 9 2 Output Mode Setting Table 1 Jumpers Setting SW1 1 SW1 2 Card Output Format Keypad Output Format ON ON 26bit Wiegand RS232 8bit Burst ON OFF 26bit Wiegand RS232 26bit Wiegand RS232 OFF ON 26bit Wiegand RS232 26bit Wiegand RS232 OFF OFF 26bit Wiegand RS232 Abit Burst X Note The default settings for SW1 1 and SW1 2 are ON short circuit IDTECK Star RFK101 9 3 Operation 9 3 1 Basic Operation 1 Once power is applied you can hear 3 initial beeps while the 3 LEDs turn on Then the only red LED light stays on indicating that the reader is in the standby mode after successful initialization and diagnostics 2 Present an RF proximity card to the reader until you hear a beep sound and see the green LED blink The reader will send the RF card data to the controller then the green LED turns off again going back to the standby mode for the next reading
11. qualified technician to restore normal operation d If the product exhibits a distinct change in performance WwW N iN al o N foe 2 General The Star RFK101 is an elegant and attractive looking 10cm 4 read range proximity reader with a Keypad The Star RFK101 has backlighting on the Keypad that ensures you successful operation even at night The Star RFK101 allows you to access the door with proximity card and PIN numbers Three LEDs of green yellow and red colors and the built in Piezo buzzer sound will guarantee you accurate and reliable system operations IDTECK Star RFK101 3 Features 125KHz Proximity amp PIN Reader PSK Modulation IDTECK Format Read Range Up to 4inch 10cm User format available Output Format Card 26bit Wiegand and RS232 default Keypad 8bit burst default 26bit Wiegand selectable or 4bit burst selectable 12 Key Numeric Keypad with Back Lighting External LED Control External Buzzer Control Tamper Switch Wall Mount US EU Asian Gang Box Size Reverse Polarity Protection Options Supervisory Signal Compatible Controller CON100 iTDC Standalone Controller Third Party Controller Identifying Supplied Parts Please unpack and check the contents of the box Star RFK101 RFK101 Wall Mount O ring User s Manual 1ea lea 5ea 1copy UR Y mu es 3 5 40 Screw 3 5 12 Screw Anchor Bolt 4ea 4ea 4ea 3ea IDTECK
12. quipment into an outlet on another circuit 4 Consult the dealer or an experienced radio TV technician for help 15 IDTECK Star RFK101 12 Warranty Policy and Limitation of Liability IDTECK warrants this product against defects in material and workmanship for 3 years from the date of purchase under normal customer use This Warranty doesn t apply 1 to any product which has been dismantled without authorization of IDTECK or and has a damaged or detached QC label on its back side 2 to any losses defects or damages caused by improper testing operation installation maintenance modification alteration or adjustment 3 to any product with a damaged or faded serial number on it or 4 to any losses defects or damages caused by lightning or other electrical discharge natural disaster misuse accident or neglect This Limited Warranty is in lieu of all other warranties obligations or liabilities on the part of IDTECK and IDTECK DISCLAIMS ANY AND ALL WARRANTY WHETHER EXPRESS OR IMPLIED OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE IDTECK does not and cannot know who is present what property is located where this product will be used it would be extremely difficult to determine the actual damages that may result from a failure of the product to perform as anticipated and the low price of this product is based upon the nature of the product provided and the limited liability that IDTECK assumes IDTECK IS NOT RESPONSIBLE
13. string 4 Enclose the product along with the RAM Code and send it to IDTECK RMA Center Product without RMA Code is not accepted If you have any questions or problems regarding the RMA services please contact us using the following contact information below Friendly representatives at IDTECK are always standing by to provide the best after sales services IDTECK Headquarter SF Ace Techno Tower B D 684 1 Deungchon Dong Gangseo Gu Seoul 157 030 Korea Tel 82 2 2659 0055 Ext 158 Fax 82 2 2659 0086 E mail webmaster idteck com Website www idteck com E Training Center http www idtecktraining com IDTECK Production Facility and RMA Center 3F 10 10 1 10 2 Dodang Dong Weonmi Gu Bucheon Si Gyeonggi Do 157 030 Korea Tel 82 2 2659 0055 Ext 158 Fax 82 2 2659 0086 E mail webmaster idteck com Website www idteck com E Training Center http www idtecktraining com 17 IDTECK Star RFK101 14 Template IDTECK Star RFK101 The specifications contained in this manual are subject to be changed without notice at any time 5F Ace Techno Tower B D 684 1 Deungchon Dong Gangseo Gu Seoul 157 030 Korea Tel 82 2 2659 0055 Fax 82 2 2659 0086 E mail webmaster idteck com Jan 2010 Copyright O IDTECK Co Ltd
Download Pdf Manuals
Related Search