Invacare® Top End® Eliminator™ OSR Racing Chair
Contents
1. 9 Using Fixed Footrest or Plastic Footplate Place feet onto footrests or plastic footplate Secure with hook and loop fastener 2 Secure ankles by wrapping ankle strap around lower footrest support tube and ankles 9 2 Adjusting Fixed Footrest Height l Loosen the set screw securing the upper and lower footrest support tubes 2 Reposition the footrest up or down as desired 3 Tighten the set screw to secure the upper and lower footrest support tubes Angle l Loosen the locknuts securing the footrest mounting bracket 2 Adjust the angle of the footrest as desired 3 Tighten the locknuts securing the footrest mounting bracket Depth l Remove the locknuts and hex screws securing the footrest mounting bracket 2 Position the footrest to the desired set of mounting holes 3 Install the hex screws through the footrest footstrap and footrest mounting bracket 4 Secure the hex screws with the locknuts Tighten securely Part No 1052767 27 Foot Strap pe 08 Fastening Strap Ankle Strap Axle Detail Adjusting Depth Footrest Mounting Holes Invacare Top End Eliminator OSR Racing Chair 10 WHEELS 10 Wheels A WARNING After any adjustments repair or service and before use make sure all attaching hardware is tightened securely Otherwise injury or damage may occur 10 1 Determining Toe In Toe Out 1 Inflate all pneumatic tires to recom2. Replacing Foot EE tre E ipe EA ati a Replacing Seat Sling Upholstery RR n Repairing Replacing Rear Wheel Tire Tube Replacing Pushrims Removing Installing Front Wheel E Replacing Brake Pads eene Removing Installing the Plastic 2 4 84 0 Replacing or Adjusting the Track Control Steering Mechanism Compensator Cylinder OPTIONS Installing Safety Lights Using Safety Helmet 3 Installing the sus sans Re OH een boost 42 Assembling Adjusting Using the Bike Rack tentent tenente nte tenten tentent tenen tten tentent teen ten ten tten tentent tentent ttn 43 Using the Alignment 45 Additional Options Invacare Top End Eliminator OSR Racing Chair 4 Part No 1052767 GENERAL General Symbols Warnings Signal words are used in this manual and apply to hazards or unsafe practices which could result in personal injury or property damage See the information below for definitions of the signal words A DANGER Danger indicates an imminently hazardous situation which if not avoided will result in death or serious injury A WARNING Warning indicates a potentially hazardous situation whi
3. 3 Safety The safety section contains important information for the safe operation and use of this product Invacare Eliminator OSR racing chair is custom built to make the most of each athlete s potential by matching up the athlete s ability with the optimum position The standard position is recommended for athletes who have limited balance and need more of a bucket or squeeze position The athlete can sit in the traditional position with his her feet on a footplate or use it in the kneeling position which makes it the ideal choice for beginners The kneeling position is best for experienced athletes with good balance who only kneel in their chair or need an amputee seat 3 General Guidelines A WARNING DO NOT use this product or any available optional equipment without first completely reading and understanding these instructions and any additional instructional material such as owner s manuals service manuals or instruction sheets supplied with this product or optional equipment If you are unable to understand the warnings cautions or instructions contact a healthcare professional dealer or technical personnel before attempting to use this equipment otherwise injury or damage may occur A qualified technician MUST perform the initial set up of this wheelchair also a qualified technician must perform all procedures specifically indicated in the manual A ACCESSORIES WARNINGS Invacare products are specifically designed an
4. 15 Reaching and Bending Forward Backward or Sideways inner 17 4 SAFETY INSPECTION TROUBLESHOOTING 18 Safety Inspection Checklist ee Ae eR ER ed eed eo NE oo acts 18 Troubleshooting 19 Suggested Maintenance Procedures i HARD OM RENE 20 5 INITIAL SETUP 21 Assembling the Eliminator Racing Wheelchair eese tenente tentent ten tentent tet ten senten teet tette senttenten tente 21 6 OPERATION 24 7 HANDLING 25 Adjusting the Track Control Steering Mechanism for Straights and Turns teens nn 25 8 UPHOLSTERY 26 Part No 1052767 3 Invacare Top End Eliminator OSR Racing Chair CONTENTS Adjusting Back Upholstery de 26 Adjusting Foot dee ete cette eden 26 FOOTREST 27 Using Fixed Footrest or PlasticiFootplate 4 2 rre hd PR emper 27 Adjusting Fixed Footrest WHEELS Determining Inf Toe Outs T 28 Adjusting Toe In Toe Out s Replacing Camber tte ER EHE LONE ERRARE ER LA ne R Re USED aes BRAKES Adjusting Brake Sensitivity Adjusting Brake Pads titt eee ce ere ce rper ette i ren eese tbe ue ERR ere cepere bte dese tee pee ta e tb cob on eet SERVICE PROCEDURES Replacing Back Upholstery zna
5. Pushrims 2 Remove the rear wheel from the racing chair Loosen the allen screws that secure the existing pushrim to the rear wheel Remove the existing pushrim Install the new pushrim onto the rear wheel and securely tighten the allen screws Ensure the rim is pushing onto the spokes at the top of D the rear wheel Reinstall rear wheel onto the racing chair Invacare Top End Eliminator OSR Racing Chair 36 Allen Wrench NX S Axle Tube Rear Wheel Front of Racing Chair Spoke a DT M Spokes Allen Screw Allen Wrench Part No 1052767 12 6 Removing Installing Front Wheel 3 Reverse the steps below to remove the front wheel There will be some play in the front wheel This is common in all front hubs Remove the two hex axles from the front wheel Line up the mounting holes in the front wheel with the holes in the forks Install the hex axles and securely tighten the front wheel to the fork 12 7 Replacing Brake Pads A WARNING Before using the racing chair inspect the brake and brake pads for proper operation and wear Replace if worn Invacare Top End recommends replacing BOTH brake pads at the same time to achieve the best brake performance as possible Remove the front wheel Remove the screws and washers that secure the existing brake pads to the brake Install the new brake pad with the arrow pointing t
6. all attaching hardware is tightened securely Otherwise injury or damage may result DO NOT overtighten hardware attaching to the frame This could cause damage to the frame tubing Before using your Invacare Top End Eliminator or Eliminator OSR check all parts for damage or wear and replace if necessary Check all parts for proper adjustment Keep axles free of dirt and lint to ensure proper fit in axle receiver Cross threading will damage the axles and axle receivers Check tires for proper pressure and if not inflated properly inflate to recommended tire pressure listed on the side wall of the tire The wheels and tires should be checked periodically for cracks and wear and should be replaced by a qualified technician Regularly check for loose spokes in the rear and front wheels If loose have them adjusted by a qualified technician Periodically check pushrims to ensure they are secured to the rear wheels Periodically adjust brake in correlation to brake pad wear Periodically check rear and front wheel bearings to make sure they are clean and free from moisture Use a Teflon lubricant if necessary 30 700 SONS CUT Check upholstery for sagging rips or tears Invacare Top End Eliminator OSR Racing Chair 20 Part No 1052767 5 INITIAL SETUP 5 Initial Setup Assembling the Eliminator Racing Wheelchair 2 A WARNING After any adjustments repair or service and before use make sure all attachin
7. de pi ce de rechange ou la r paration de n importe lequel tel produit Le devoir seul d Invacare et votre rem de exclusif sous cette garantie seront limit s tel remplacement de et ou de r paration Pour le service de garantie s il vous plait contacter le n gociant de que vous avez achet votre produit d Invacare Dans l v nement vous ne recevez pas le service de garantie satisfaisant s il vous plait crire directement Invacare l adresse au dessous Fournir le nom du n gociant l adresse la date d achat indiquer la nature du d faut et si le produit est mis en serie indique le num ro de s rie Ne pas retourner des produits notre usine sans notre consentement pr alable Limitations et Exclusions La garantie qui ne pr c de pas s appliquera aux produits num rot s en s rie si le num ro de s rie a t enlev ou a t d figur les produits ont expos la n gligence l accident l op ration d plac e l entretien ou l emmagasinage la publicit ou l usage institutionnel les produits ont modifi sans Invacare le consentement crit expr s y compris mais pas limit la modification par l usage de parties ou les attachements non autoris es les produits endommag s par la raison de r parations faites au composant sans le consentement sp cifique d Invacare ou A un produit endommag par les circonstances au del du contr le d Invacare et telle valuation sera seulement d termin e par Invacare La g
8. on the rim of the wheel If not adjust the brake pads Repeat this procedure until the brake is adjusted properly Securely tighten the allen screw that maintains the tautness of the brake cable Part No 1052767 3l Brake Cable Invacare Top End Eliminator OSR Racing Chair BRAKES 11 2 Adjusting Brake Pads A WARNING Before using the racing chair inspect the brake and brake pads for proper operation and wear Replace if worn 1 Loosen the allen screw that secures the brake pad to the brake 2 Position the brake pad until it is in line with the rim of the front wheel Brake Pad 3 Securely tighten the allen screw that secures the brake pad to the brake Repeat this procedure for the opposite side 5 Adjust the brake Invacare Top End Eliminator OSR Racing Chair 32 Part No 1052767 12 Service Procedures 12 1 l Replacing Back Upholstery Unlatch the three fastening flaps that secure the back upholstery to the racing chair frame Unlatch the foot pouch of the leg cushion from the back upholstery kneeling upholstery only Unlatch the bottom of the back upholstery from the seat sling upholstery Remove the existing back upholstery from the racing chair Feed the top two fastening flaps of the new back upholstery through the slots on the racing chair frame Feed the bottom fastening flap of the new back upholstery between the racing chair frame and the clothing guards Adjust the back uphols
9. so the rear wheels sit in the rear wheel bar brackets Remove the two mounting bolts and locknuts securing the rear wheel bar to the wheel tray Position the rear wheel bar to one of three mounting positions on the wheel tray Secure the rear wheel bar to the wheel tray with the two mounting bolts and locknuts Invacare Top End Eliminator OSR Racing Chair Mounting Rear Bolts and Wheel Locknuts Screws Small Mounting Bolts and Locknuts Large Mounting Bolts and Locknuts Rear Wheel Bar Bracket Bracket Wheel Stop Wheel Stop Mounting Position Wher Tray Mounting Bolts and Locknuts Wheel Tray Bracket Part No 1052767 Using the Bike Rack Position the racing chair on the rack with the front wheel in the wheel tray bracket Adjust the bike rack so the wheel tray bracket sits against the front wheel and the rear wheel bar brackets sit against the rear wheels l 2 3 4 Secure the front wheel to the wheel tray bracket using the strap provided Secure the rear wheels to the rear wheel bar using the straps provided 13 5 Using the Alignment Gauge Su AWD N Inflate the tires to recommended tire pressures listed on the sidewall of the tire Place the racing chair and alignment gauge on a flat surface Position the alignment gauge near the rear of the rear tires Loosen the alignment screw on each side Position the alignment gauge between the rear of the rear tires
10. turn when using the track control steering mechanism B For fine track control steering adjustment refer to Adjusting the Track Control Steering Mechanism for Straights and Turns on page 25 Part No 1052767 12 SERVICE PROCEDURES Invacare Top End Eliminator OSR Racing Chair 12 SERVICE PROCEDURES 12 10 Compensator Cylinder Replacement l Remove A Loosen and remove the nut not shown that attaches one end of the compensator cylinder to the track control steering mechanism B Remove the bolt and nut not shown that attach the compensator cylinder to the clamp on the fork 2 Replace A Putthe end of the compensator cylinder in place on the clamp picture A B Putthe screw into the mounting hole on the clamp picture B C Putanuton the end of the screw and tighten securely with an Allen wrench picture C D Putthe opposite end of the compensator cylinder in place on the track control steering mechanism and attach with a screw and nut picture D Tighten securely with an Allen wrench The racing wheelchair should be aligned straight after assembly Refer to picture E The clamp can be moved on the fork if necessary Invacare Top End Eliminator OSR Racing Chair E 24 Clamp be adjusted on fork if necessary 40 Part No 1052767 13 OPTIONS 13 Options A WARNING After any adjustments repair or service and before use make sure all att
11. 16 Isny Tel 49 0 75 62 7 00 0 Fax 49 0 75 62 7 00 66 info invacare aquatec com WWN invacare aquatec de European Distributor Organisation Invacare KleiststraBe 49 D 32457 Porta Westfalica Tel 49 0 57 31 754 540 Fax 49 0 57 31 754 541 edo invacare com www invacare eu com Espafia Invacare SA c Areny s n Poligon Industrial de Celra E 17460 Celra Girona Tel 34 0 972 49 32 00 Fax 34 0 972 49 32 20 contactsp invacare com www invacare es France Invacare Poirier SAS Route de St Roch F 37230 Fondettes Tel 33 0 2 47 62 64 66 Fax 33 0 2 47 42 12 24 contactfr invacare com www invacare fr Ireland Invacare Ireland Ltd Unit 5 Seatown Business Campus Seatown Road Swords County Dublin Ireland Tel 353 810 7084 Fax 353 810 7085 ireland invacare com www invacare ie Italia Invacare Mecc San s r l Via dei Pini 62 36016 Thiene Tel 39 0445 38 00 59 Fax 39 0445 38 00 34 italia invacare com www invacare it Invacare Top End Eliminator OSR Racing Chair Nederland Invacare BV Celsiusstraat 46 NL 6716 BZ Ede Tel 31 0 318 695 757 Fax 31 0 318 695 758 nederland invacare com www invacare nl csede invacare com Norge Invacare AS Grensesvingen 9 Postboks 6230 Etterstad N 0603 Oslo Tel 47 0 22 57 95 00 Fax 47 0 22 57 95 01 norway invacare com www invacare no island invacare com Osterreich Invacare Austria GmbH Herzog Odilostra
12. 7 12 3 Replacing Seat Sling Upholstery l 2 Remove seat cushion from seat sling upholstery Unlatch the fastening flap that secures the existing seat upholstery to itself Slide the ends of the existing seat upholstery up and through the frame of the racing chair Slide the new upholstery through the frame of the racing chair Pull che seat upholstery to the desired tautness and secure with the fastening flap Reverse STEPS 1 5 to reassemble Part No 1052767 35 12 SERVICE PROCEDURES Racing Chair Frame Seat Upholstery Fastening Flap Invacare Top End Eliminator OSR Racing Chair 12 SERVICE PROCEDURES 12 4 Repairing Replacing Rear Wheel Tire Tube WARNING Replacement of a clincher tire or tube MUST be performed by a qualified technician Tubular tires are tires with tubes sewn into the tires They are high pressure 140 Ibs psi and MUST be glued to the rim Once they have a hole in them they MUST be replaced Tubular tires will lose air overnight but they are not faulty This is a characteristic of tubular tires Tubular tires DO NOT fit on a clincher rim Clincher tires are not like conventional bicycle tires There is an inner tube separate from the actual tire They are more durable for longer periods of time and if punctured the tube can be replaced by a qualified technician Clincher tires use 100 Ibs psi Clincher tires DO NOT fit on a tubular rim 12 5 Replacing
13. Adjust the alignment inserts so the alignment gauge fits snugly between the rear of the rear tires Tighten the alignment screws to secure the alignment bar position Position the alignment gauge at the front of the rear tires and repeat Examine the gauge Perform one of the following A If the alignment gauge fits snugly between the front of the rear tires the wheels are aligned No toe in toe out adjustment is required B is extra space between the alignment gauge and rear tires the tires have a toe out condition Refer to Adjusting Toe In Toe Out on page 29 C Ifthe alignment gauge does not fit between rear tires the tires have a toe in condition Refer to Adjusting Toe In Toe Out on page 29 Part No 1052767 45 13 OPTIONS Alignment Gauge Front of Racing Chair Rear tires Front Measurement Rear Measurement 2 2 Rear of Racing Chair Invacare Top End Eliminator OSR Racing Chair I3 OPTIONS 13 6 Additional Options These options are available for order through www topendwheelchair com or 1 800 532 8677 A Heart rate monitor The monitor is usually mounted on the crank assembly The user attaches the heart rate monitor around his her chest with a strap that is included with this option B Click Strap Attach with heavy duty zip ties to the cage C Wheel Bag Wheel bag can fit up to three wheels Remove and place axles in the bottom of the wheel bag to ensure they are not dama
14. Invacare Top End Eliminator OSR Racing Chair User Manual This manual MUST be given to the user of the product BEFORE using this product read this manual and save for future reference Yes you can 9 2011 Invacare Corporation All rights reserved Republication duplication or modification in whole or in part is prohibited without prior written permission from Invacare Trademarks are identified by and All trademarks are owned by or licensed to Invacare Corporation or its subsidiaries unless otherwise noted Teflon is a registered trademark of E l Du Pont De Nemours and Company Invacare Top End Eliminator OSR Racing Chair 2 Part No 1052767 CONTENTS User Manual DEALER This manual MUST be given to the user of the product USER BEFORE using this product read this manual and save for future reference GENERAL 5 SyYMPBOIS EEE Mr Si re 5 Dealer Technician Information 5 Warranty Information 6 European Limited Warranty Information and Customer Service sense 8 2 OVERVIEW 9 Label Location and Component Identification nn 9 Typical Product Parameters ee E E e d ee 10 Tire Pressure CONVeFSiOn sine 10 3 SAFETY G n ral Guidelines sS E Operating Informations Rl e e E etr ie EREMO arse ER Mo oes esie a 12 Transferring Into Out of the Racing Chair
15. Top view of Locknuts Mechanism racing chair Part No 1052767 25 Invacare Top End Eliminator OSR Racing Chair 8 UPHOLSTERY 8 Upholstery A WARNING After any adjustments repair or service and before use make sure all attaching hardware is tightened securely Otherwise injury or damage may occur If the racing chair is equipped with kneeling upholstery always ensure the footpouch is securely latched to the back upholstery Otherwise injury may occur 8 1 Adjusting Back Upholstery Unlatch the three fastening flaps that secure the back upholstery to the racing chair frame 2 Adjust the back upholstery to the desired tautness TIGHTER upholstery will increase the stability and maintain normal maneuverability of the racing chair because the user is pushed forward in the racing chair slightly LOOSER upholstery will increase the maneuverability and make the racing chair less stable because additional weight is being distributed onto the rear wheels 8 2 Adjusting Foot Pouch Unlatch three fastening flaps 2 Adjust the foot pouch to the desired tautness Invacare Top End Eliminator OSR Racing Chair 26 Part No 1052767 9 Footrest A WARNING damage may occur 9 FOOTREST After any adjustments repair or service and before use make sure all attaching hardware is tightened securely Otherwise injury or Feet MUST be secured into the fixed footrest BEFORE using racing chair Otherwise injury or damage may occur
16. aching hardware is tightened securely Otherwise injury or damage may occur 13 1 Installing Safety Lights WARNING Operation of the handcycle is subject to all traffic rules and regulations this may include the use of a safety lights and reflectors for dusk night riding Batteries Remove the lens cover 2 Insert the AAA batteries with correct polarity or 3 Reinstall lens cover Mounting the Safety Light l Remove the set screw from the clamp on the safety light 2 Install the safety light A Rear safety light Pull the back cushion off of the back frame Position the clamp onto the rear seat post Install the set screw into the clamp and tighten securely B Front safety light Position the clamp onto the side frame Install the set screw into the clamp and tighten securely Operating the Safety Light 1 Press GREY button to turn safety light on off 2 Remove lens cover and slide switch back and forth for pulse or constant mode Part No 1052767 41 Invacare Top End Eliminator OSR Racing Chair 13 OPTIONS 13 2 Using Safety Helmet Helmet l Secure helmet using the chin strap PEN 2 Ensure proper fit FO 13 3 Installing the Computer 1 Install metal plug onto spoke of the racing chair approximately 2 inches from wheel rim 2 Align metal plug with fork assembly 3 Secure sensor to fork using hardware provided Slot in sensor MUST align with metal plug for mileage etc to be registered on th
17. arantie ne s appliquera pas aux probl mes r sultant de l usure normale l usage sur un cylindre de formation int rieur ou un chec pour adh rer ces instructions La garantie qui pr c de est exclusive et au lieu et place de toutes les autres garanties expresses Les garanties implicites si n importe lequel y compris les garanties implicites de valeur marchande et de sant pour un but particulier ne s tendra pas au del de la dur e de la garantie expresse a fourni en ceci et le rem de pour les violations de garantie implicite sera limit pour r parer ou le remplacement du produit d fectueux conform ment aux termes a contenu en ceci Invacare ne sera pas responsable de des dommages cons quents ou accessoires que ce soit CETTE GARANTIE SERA ETENDUE POUR SE CONFORMER A DECLARE PROVINCIAL LOIS ET AUX CONDITIONS Part No 1052767 7 Invacare Top End Eliminator OSR Racing Chair GENERAL 1 4 European Limited Warranty Information and Customer Service For more information on Limited Warranty within Europe please contact the Invacare representative within your country Belgium amp Luxemburg Invacare nv Autobaan 22 B 8210 Loppem Tel 32 0 50 83 10 10 Fax 32 0 50 83 10 II belgium invacare com www invacare be Danmark Invacare A S Sdr Ringvej 37 DK 2605 Br ndby Tel 45 0 36 90 00 00 Fax 45 0 36 90 00 0I denmark invacare com www invacare dk Deutschland Invacare Aquatec GmbH AlemannenstraBe 10 D 883
18. ch If the axle does not thread smoothly DO NOT force Line up and try to thread again Allen Wrench Axle Tube Rear Wheel Part No 1052767 23 Invacare Top End Eliminator OSR Racing Chair 6 OPERATION 6 Operation A WARNING Before using your Invacare Top End Eliminator or Eliminator OSR check all parts for damage or wear and replace if necessary Check all parts for proper adjustment After any adjustments repair or service and before use make sure all attaching hardware is tightened securely Otherwise injury or damage may occur Before operating the handcycle review the General Guidelines in this user manual Transfer into the racing wheelchair 2 Check and adjust the upholstery if necessary A WARNING If the racing chair is equipped with kneeling upholstery always ensure the footpouch is securely latched to the back upholstery Otherwise injury may occur 3 Check Brakes Check cable for signs of wear or fraying Squeeze the brake lever firmly and check for proper brake function Adjust for pad wear if necessary Check pads for wear and replace if necessary 4 Secure feet on the fixed footrest if installed on the plastic foot plate or if sitting in the kneel only position within the foot pouch which is part of the kneeling upholstery 5 Placeat least one hand on the handrim s Rotate the handrim forward toward the front to propel the racing chair forward Invacare Top End Elimi
19. ch if not avoided could result in death or serious injury A CAUTION Caution indicates a potentially hazardous situation which if not avoided may result in property damage or minor injury or both IMPORTANT Indicates a hazardous situation that could result in damage to property if it is not avoided Gives useful tips recommendations and information for efficient trouble free use 1 22 Dealer Technician Information The term qualified technician in this manual refers to an Invacare qualified technician or a Shimano certified bicycle repair technician Part No 1052767 5 Invacare Top End Eliminator OSR Racing Chair GENERAL 1 3 Warranty Information United States Limited Warranty PLEASE NOTE THE WARRANTY BELOW HAS BEEN DRAFTED TO COMPLY WITH FEDERAL LAW APPLICABLE TO PRODUCTS MANUFACTURED AFTER JULY 4 1975 This warranty is extended only to the original purchaser who purchases this product when new and unused from Invacare or a dealer This warranty is not extended to any other person or entity and is not transferable or assignable to any subsequent purchaser or owner Coverage under this warranty will end upon any such subsequent sale or other transfer of title to any other person This warranty gives you specific legal rights and you may also have other legal rights which vary from state to state Invacare warrants the Eliminator OSR frame to be free from defects in materials and workmanship for a period of two years
20. d manufactured for use in conjunction with Invacare accessories Accessories designed by other manufacturers have not been tested by Invacare and are not recommended for use with Invacare products NOTICE THE INFORMATION CONTAINED IN THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE Check all parts for shipping damage and test before using In case of damage DO NOT use Contact Invacare Carrier for further instruction Part No 1052767 11 Invacare Top End Eliminator OSR Racing Chair 3 SAFETY 3 2 Operating Information A WARNING RACING CHAIR USER As a manufacturer of racing chairs Invacare endeavors to supply a racing chair to meet many needs of the end user However final selection of a racing chair to be used by an individual rests solely with the user and his her health care professional capable of making such a selection Use this information only as a basic guide The techniques that are discussed on the following pages have been used successfully by many The user is responsible for normal upkeep and maintaining the racing chair in proper operating condition TRANSPORT Invacare recommends that a user is NOT transported in vehicles of any kind while in a racing chair As of this date the Department of Transportation has not approved any tie down systems for transportation of a user while in a racing chair in a moving vehicle of any type SERIOUS INJURY CAN OCCUR IN THE EVENT OF A FALL FROM THE PRODUCT Feet MUST be secure Use
21. e l acheteur original ach te ce produit quand nouvel et inutilis d Invacare ou un n gociant Cette garantie n est pas tendue aucune autres personne ou aucune entit et n est pas transmissible ou ascribable l acheteur ou le propri taire subs quent La couverture sous cette garantie terminera sur n importe lequel telle vente subs quente ou tel autre transfert de titre aucune autre personne Cette garantie vous donne des droits l gaux sp cifiques et vous pouvez avoir aussi d autres droits l gaux qui varie de l tat pour d clarer Invacare m rite le cadre d OSR d Eliminateur pour tre libre des d fauts dans les mat riels et de l ex cution pour une p riode de deux ans de la date d achat au propri taire original Tout le composant s pare y compris mais n a pas limit pour cintrer des tubes le compensateur et le rev tement est m rit contre les d fauts dans les mat riels et l ex cution pour une p riode de l un 1 l an de la date de facture originale sauf la direction des cylindres le coussin les bagnes les rapports les c bles et les fatigue tubes Les roues de fibre de carbone sont assujettis la garantie du fabricant de roue et ne sont pas m rit par Invacare Si dans telle p riode de garantie n importe lequel tel produit sera r v l d fectueux tel produit sera r par ou sera remplac l option d Invacare Cette garantie n inclut pas le travail ou les frais d exp dition ont contract dans l installation
22. e computer 4 Snap computer into mounting bracket oe Install spacer on the back of the computer mounting bracket 6 Secure mounting bracket to crank bottom bracket with zip or wire ties Invacare Top End Eliminator OSR Racing Chair 42 Part No 1052767 I3 OPTIONS 13 4 Assembling Adjusting Using the Bike Rack A WARNING After any adjustments repair or service and before use make sure all attaching hardware is tightened securely Otherwise injury or damage may occur Assembling the Bike Rack Position the receiver with the bracket facing up Position the rear wheel bar with the wheel brackets facing up Remove the two large mounting bolts and locknuts from the receiver and set aside Remove the two small mounting bolts and locknuts from the receiver bracket and set aside Secure the wheel tray to the receiver with the two large mounting bolts and locknuts Using two small mounting bolts and locknuts secure the receiver bracket to the wheel tray Remove the two mounting bolts and locknuts from the rear wheel bar and set aside Using two mounting bolts and locknuts secure the rear wheel bar to the wheel tray 30 700 lr Une ob Install the receiver onto the trailer hitch of the vehicle according to the vehicle manufacturer s instructions Adjusting the Bike Rack WARNING After any adjustments repair or service and before use make sure all attaching hardware is tightened securely Otherwise injury o
23. enter of gravity and may cause you to tip over Position the racing chair as close as possible to the desired object Reach back only as far as your arm will extend without changing your sitting position DO THIS Part No 1052767 17 Invacare Top End Eliminator OSR Racing Chair 4 SAFETY INSPECTION TROUBLESHOOTING 4 Safety Inspection Troubleshooting Every six months or as necessary take your Top End racing chair to a qualified technician for a thorough inspection and servicing Regular cleaning will reveal loose or worn parts and enhance the smooth operation of your racing chair For safe and proper operation your racing chair MUST be cared for just like any other vehicle Routine maintenance will extend the life and efficiency of your racing chair 4 1 Safety Inspection Checklist Initial adjustments should be made to suit your personal body structure and preference Thereafter follow these maintenance procedures Inspect Adjust Initially and Weekly Q Make sure that the racing chair rolls straight no excessive drag or pull to one side Inspect seat and back upholstery for rips or sagging Inspect that rear wheel axles are securely tightened Inspect that there is no excessive side movement or binding when rear wheel is lifted and spun Inspect pushrims for signs of rough edges or peeling of rubber coating where it might separate from the pushrim Inspect spokes for bent or broken spokes Inspect that all spokes are uniform
24. from date of purchase to the original owner or with a copy of the seller s invoice required for coverage under this warranty All component parts including but not limited to fork compensator and upholstery are warranted against defects in materials and workmanship for a period of one 1 year from the original invoice date except steering cylinders cushion bushings bearings cables and tires tubes Carbon fiber wheels are subject to the wheel manufacturer s warranty and are not warranted by Invacare If within such warranty period any such product shall be proven to be defective such product shall be repaired or replaced at Invacare s option This warranty does not include any labor or shipping charges incurred in replacement part installation or repair of any such product Invacare s sole obligation and your exclusive remedy under this warranty shall be limited to such repair and or replacement For warranty service please contact the dealer from whom you purchased your Invacare product In the event you do not receive satisfactory warranty service please write directly to Invacare at the address below Provide dealer s name address date of purchase indicate nature of the defect and if the product is serialized indicate the serial number Do not return products to our factory without our prior consent Limitations and Exclusions The foregoing warranty shall not apply to serial numbered products if the serial number has been removed or defaced p
25. g hardware is tightened securely Otherwise injury or damage may occur STEP 2 Use an Allen key to remove the fork cap Remove the top three pieces of hardware two washers and a bearing from the fork Two other washers and a bearing must stay in place on the fork DO NOT remove them Insert the fork into the frame headtube Put two washers and bearing onto the fork Put the steering handle onto the fork Part No 1052767 21 Invacare Top End Eliminator OSR Racing Chair INITIAL SETUP Put the fork cap onto an Allen wrench STEP 6 Attach the fork cap to the fork Tighten securely v Put the compensator cylinder clamp onto the steering handle Remove the screw from the compensator cylinder clamp with an Allen wrench 9 Put the compensator cylinder and screw in place the compensator cylinder clamp Tighten the screw securely STEP 8 STEP 9 Invacare Top End Eliminator OSR Racing Chair 22 Part No 1052767 10 11 12 13 5 INITIAL SETUP There is a RIGHT and LEFT rear wheel The pushrims should be pushing into the spokes at the top of the rear wheel Determine the right and left rear wheel Apply a small amount of grease onto the axle Let some air out of the tire so it will fit under the fender Insert the axle into the axle tube on the racing chair frame and guide rear wheel under fender Securely tighten the axle to the racing chair frame using the allen wren
26. ged D Plastic Footplate with Strap E Fixed Footrest F Cushion G Safety Flag Mount safety flag in holder secured to back tube on bike frame Invacare Top End Eliminator OSR Racing Chair 46 B ss mil DCS m Part No 1052767 13 OPTIONS NOTES Part No 1052767 47 Invacare Top End Eliminator OSR Racing Chair gt Yes you can Invacare Corporation www invacare com and www topendchair com USA One Invacare Way Elyria Ohio USA 44036 2125 800 333 6900 EU Representative Invacare International Sarl Route de Cit Ouest 2 1196 Gland Switzerland Tel 41 22 354 60 10 Fax 41 223546011 Manufactured by Top End Sports and Recreation Products 4501 63rd Circle North Pinellas Park Florida 33781 5914 727 522 8677 800 532 8677 Part No 1052767 Rev C 10 11
27. holstery knee and or foot position as well as the user condition directly relate to the stability of the racing chair Any change to one or any combination of the three may cause the racing chair to decrease in stability The object you are transferring into or out of MUST also be secured before attempting any transfer KNEELING SEAT UPHOLSTERY Ensure that feet slide evenly into the foot pouch and avoid the rear wheel spokes Ensure that the foot pouch is securely latched to the back upholstery Otherwise injury can occur WHEELCHAIRS Wheel locks are not brakes Engaging the wheel locks may not prevent the wheelchair from moving on all floor surfaces including those that may be wet or slick ALWAYS exercise caution when transferring into or out of the wheelchair Invacare strongly recommends an experienced assistant help in the transferring to and from the racing chair The assistant should hold down the front of the racing chair to avoid any instability that may occur Some racers will rest on the frame cage of the racing chair half way through the transfer and move the RIGHT hand to the right side of the frame Part No 1052767 15 Invacare Top End Eliminator OSR Racing Chair 3 SAFETY 1 Perform one of the following A Kneeling Upholstery Transfer vi vii viii ix Position the chair as close as possible along side the seat to which you are transferring Shift body weight to the edge of the wheelchair upholstery closest t
28. hook and loop straps to secure feet before use of the racing chair BRAKES If the brake cable show signs of wear the cable MUST be replaced or the brake may fail ALWAYS check the function of the brake Be sure that the brakes and all other features of your racing chair are operating properly Should the primary brake fail place a gloved hand on a rear wheel to slow the racing chair to a stop Care consideration and practice MUST be taken and observed in the following safety points Otherwise injury or damage may occur Safe use requires the close attention of the user as well as the assistant This user manual points out the most common procedures and techniques involved in the safe operation and maintenance of the racing chair It is important to practice and master these safe techniques until you are comfortable in maneurvering the racing chair A helmet MUST ALWAYS be worn when operating the racing chair Invacare Top End Eliminator OSR Racing Chair 12 Part No 1052767 3 SAFETY A WARNING RISK OF INJURY OR DAMAGE The manufacturer is not responsible for failure damage or injury caused by improper operation or maintenance by the end user To determine and establish your particular safety limits practice transferring activities in the presence of a qualified health care professional before attempting active use of the racing chair Operation of the racing chair is subject to all traffic rules and regulations This may include the
29. if wheel wobbles noticeably or binds to a stop There will be some play in the front wheel Inspect that the wheel bearings are clean and free of moisture Inspect that the brake does not interfere with front wheel when rolling Inspect that there is no excessive wear of brake pads Inspect Adjust Periodically Do Make sure that the racing chair rolls straight no excessive drag or pull to one side Inspect upholstery for rips or sagging Inspect that rear wheel axles are securely tightened Inspect that there is no excessive side movement or binding when rear wheel is lifted and spun Inspect pushrims for signs of rough edges or peeling of tire tape coating where it might separate from the pushrim Inspect that the wheel bearings are clean and free of moisture Inspect that the brake is easy to engage Clean upholstery with light detergent and water 4 2 Troubleshooting Veers Right Veers Left Sluggish Turn or Performance Squeaks and Rattles Looseness in Chair Solutions x X X Check tires for correct and equal pressure X X Check for loose stem nuts X X Check spokes and nipples X X X Adjust track control steering mechanism Check toe out Part No 1052767 19 Invacare Top End Eliminator OSR Racing Chair 4 SAFETY INSPECTION TROUBLESHOOTING 4 3 Suggested Maintenance Procedures A WARNING After any adjustments repair or service and before use make sure
30. ly tight Inspect front wheel fork assembly for proper tension by front wheel front wheel should come to a gradual stop Loosen tighten allen screws if wheel wobbles noticeably or binds to a stop There will be some play in the front wheel Inspect that the wheel bearings are clean and free of moisture Inspect that the brake does not interfere with front wheel when rolling Inspect that the brake is easy to engage Inspect that there is no excessive wear of brake pads A CAUTION As with any vehicle the wheels and tires should be checked periodically for cracks flat spots and wear and should be replaced 0000000 Inspect tires for flat spots and wear Check pneumatic tires for proper inflation Check frame cage for interference with tires Clean upholstery with light detergent and water Inspect for bent or broken frame Invacare Top End Eliminator OSR Racing Chair 18 Part No 1052767 a a a 4 SAFETY INSPECTION TROUBLESHOOTING If installed inspect the fixed footrest mounting hardware to ensure it is tight and the footrest secure Inspect footrest straps for wetness and or damage Inspect seat positioning straps for any signs of wear Replace if necessary Inspect Adjust Monthly a a a a Inspect that rear wheel axles are securely tightened Inspect front wheel fork assembly for proper tension by front wheel front wheel should come to a gradual stop Loosen tighten allen screws
31. mended tire pressures listed on the sidewall of the tire 2 Measure the distance between the center lines at the rear and front of the rear wheels at approximately 2 inches from the ground floor For optimum accuracy perform STEP 2 with the racing chair occupied STEP 2 may be performed with using alignment gauge available as an option for the racing chair 3 Determine the difference between the two measurements If the difference between the two measurements is greater than 2 inch 0 1 4 inch for maximum rollability one of two conditions exists If the rear centerline measurement of the rear wheels is SMALLER than the front centerline measurement of the rear wheels a toe out condition exists If the rear centerline measurement of the rear wheels is LARGER than the front centerline measurement of the rear wheels a toe in condition exists 4 If the difference between the measurements is greater than 8 inch correct the toe in toe out condition Invacare Top End Eliminator OSR Racing Chair 28 Top View of racing chair Front of racing chair Toe out Smaller Than Front B C Larger Than Front Part No 1052767 10 2 Adjusting Toe In Toe Out Loosen but do not remove the socket screws and clamps that secure camber inserts to the camber bar Slowly rotate the camber insert until the rear wheels are approximately in a straight line Securely tighten the socket screws and clamp
32. nator OSR Racing Chair 24 Part No 1052767 7 HANDLING 7 Handling A WARNING After any adjustments repair or service and before use make sure all attaching hardware is tightened securely Otherwise injury or damage may occur 7 Adjusting the Track Control Steering Mechanism for Straights and Turns The procedures in this section apply to a counter clockwise race track Reverse the right and left instructions for a clockwise race track Different speeds and conditions will affect the way the racing chair handles Extreme crosswinds should be taken into consideration Adjustments to the track control steering mechanism should be made while sitting in the racing chair To prevent disqualification it is critical that the track control steering mechanism be set to control the chair within the assigned lane and at the speed you intend to race at Straights Racing Chair PP ert Frame l Turn front wheel until it is approximately in a straight line Track Stop 2 Turn the right track stop screw until the locknut on the track stop Screw tums Track Stop is touching the racing chair frame Screw 3 Repeat STEPS 2 until the racing chair follows a straight line straights Turns tin rl l Turn front wheel until in required position for turn N is 2 Turn the left track stop screw until it is touching the racing chair frame b pu d 3 Repeat STEPS 2 until racing chair follows the desired turn Track Control Steering
33. nsfer to from the racing chair remember to use good body mechanics Keep your back straight and bend your knees when lifting or positioning the racing chair for the end user Also be aware of detachable parts These must NEVER be used for lifting supports or to move the racing chair as they may be inadvertently released resulting in possible injury to the user and or assistant PERCENTAGE OF WEIGHT DISTRIBUTION The tautness of the back upholstery knee and or foot position as well as the user condition directly relate to the stability of the racing chair Any change to one or any combination of the three may cause the racing chair to decrease in stability Turning and cornering will cause a change to the normal balance the center of gravity and the weight distribution of the racing chair To determine and establish your particular safety limits practice transferring activities in several combinations in the presence of a qualified health care professional before attempting a transfer alone Proper positioning is essential for your safety Invacare Top End Eliminator OSR Racing Chair 14 Part No 1052767 3 SAFETY 3 3 Transferring Into Out of the Racing Chair WARNING Before attempting to transfer in or out of the racing chair every precaution should be taken to reduce the gap distance Position the racing chair on level ground and as close as possible to the object you are transferring into or out of The tautness of the back up
34. o the racing chair Place LEFT leg on top of the LEFT cage frame Start RIGHT leg into the kneeling upholstery and UNDER the seat sling Start LEFT leg into the kneeling upholstery and UNDER the seat sling Place LEFT hand on the frame cage Place RIGHT hand on the racing chair frame Lift and shift weight into racing chair upholstery Tighten straps and the top of the fender A Standard Upholstery Transfer vii viii Position the chair as close as possible along side the seat to which you are transferring Shift body weight to the edge of the racing chair upholstery closest to the racing chair Place LEFT leg through the opening in the frame cage Place LEFT hand on the frame cage Place RIGHT hand on the wheelchair frame Lift and shift weight into the racing chair upholstery Strap feet onto the footplate Strap the knees up into a safe and comfortable position Tighten straps and the top of the fender Invacare Top End Eliminator OSR Racing Chair Kneeling Upholstery Transfer STEP ii STEP iii STEP iv Standard Upholstery Transfer Once seated in the racing chair move your feet back as close as possible to the axle as you feel comfortable and tighten the knee strap STEP ii STEP vii STEP iii STEP v STEP vi Part No 1052767 3 SAFETY 3 4 Reaching and Bending Forward Backward or Sideways A WARNING DO NOT sit erect or lean over the top of the back upholstery This will change your c
35. owards the front of the racing chair with the existing hardware Repeat this procedure for the opposite brake pad Install the front wheel onto the racing chair Adjust the brake pads as necessary Part No 1052767 37 12 SERVICE PROCEDURES Hex Axle TT TT OQ Coen OLE RTE Front Wheel Brake Pad Washer s 9 Arrow Allen Screw Invacare Top End Eliminator OSR Racing Chair 12 SERVICE PROCEDURES 12 8 Removing Installing the Plastic Footplate Perform one of the following Toremove loosen the fastening strap and remove the Seat Frame footplate e install secure the fastening straps around the frame Fastening Strap Axle Plastic Footplate Invacare Top End Eliminator OSR Racing Chair 38 Part No 1052767 12 9 Replacing or Adjusting the Track Control Steering Mechanism Replacing A sure that the leather spacer is in place on the bolt picture A If not order a replacement leather spacer B Put the track control steering mechanism on the bolt picture The bolt in the fork should never be tightened otherwise the loctite seal will be broken C Place the nut over bolt and tighten securely picture C Adjusting A Loosen or tighten the nut picture C The nut should not be so tight that the track steering control mechanism won t move or too loose so that the front wheel doesn t
36. r damage may occur To properly secure the racing chair the wheel tray bracket should be adjusted to sit against the front wheel Wheel Tray Bracket l Remove the four mounting bolts and locknuts securing the wheel tray bracket to the wheel tray 2 Position the wheel tray bracket in the desired position 3 Secure the wheel tray bracket to the wheel tray with the four mounting bolts and locknuts Part No 1052767 43 Invacare Top End Eliminator OSR Racing Chair 13 OPTIONS 4 If necessary the wheel stop may be adjusted to one of three positions to sit against the front wheel To adjust the wheel stop perform the following steps A Remove the mounting bolt and locknut securing the wheel stop to the wheel tray bracket B Position the wheel stop in the desired mounting position C Secure the wheel stop to the wheel tray bracket with the mounting bolt and locknut Rear Wheel Bar Brackets l 2 3 4 Rea To properly secure the racing chair the rear wheel bar brackets should be adjusted to sit against the rear wheels Loosen the two screws securing the rear wheel bar bracket to the rear wheel bar Adjust the rear wheel bar bracket in out until they sit against the rear wheel Secure the rear wheel bar bracket to the rear wheel bar with the two screws Repeat steps 3 for the opposite side if necessary r Wheel Bar To properly secure the racing chair the rear wheel bar should be adjusted
37. roducts subjected to negligence accident improper operation maintenance or storage commercial or institutional use products modified without Invacare s express written consent including but not limited to modification through the use of unauthorized parts or attachments products damaged by reason of repairs made to any component without the specific consent of Invacare or to a product damaged by circumstances beyond Invacare s control and such evaluation will be solely determined by Invacare The warranty shall not apply to problems arising from normal wear use on an indoor training roller or failure to adhere to these instructions The foregoing warranty is exclusive and in lieu of all other express warranties Implied warranties if any including the implied warranties of merchantability and fitness for a particular purpose shall not extend beyond the duration of the express warranty provided herein and the remedy for violations of any implied warranty shall be limited to repair or replacement of the defective product pursuant to the terms contained herein Invacare shall not be liable for any consequential or incidental damages whatsoever THIS WARRANTY SHALL BE EXTENDED TO COMPLY WITH STATE PROVINCIAL LAWS AND REQUIREMENTS Invacare Top End Eliminator OSR Racing Chair 6 Part No 1052767 GENERAL Canadian Limited Warranty i ue ur origi ui uit qu uv inutilis u un n gociant i Cette garantie est seulement tendu
38. s that secure the camber inserts to the camber bar Measure the distance between the center lines at the rear and front of the rear wheels at approximately 12 inches from the ground floor Repeat STEPS 4 until the toe in toe out measurement is less than 1 8 inch for maximum rollability Part No 1052767 29 10 WHEELS Clamp Invacare Top End Eliminator OSR Racing Chair 10 WHEELS 10 3 Replacing Camber Inserts Loosen but do not remove the socket screws and clamps that secure the camber inserts to the camber bar Remove the existing camber insert from the camber bar Install the new camber insert into the camber bar D NN Adjust the toe in toe out of the racing chair Refer to Adjusting Toe In Toe Out on page 29 Invacare Top End Eliminator OSR Racing Chair 30 Part No 1052767 Brakes A WARNING BRAKES After any adjustments repair or service and before use make sure all attaching hardware is tightened securely Otherwise injury or damage may occur 11 Adjusting Brake Sensitivity A WARNING Before using the racing chair inspect the brake and brake pads for proper operation and wear Replace if worn Loosen the allen screw that maintains the tautness of the brake cable Squeeze both brake pads with your hand to adjust the brake cable Loosely tighten the allen screw to ensure that the brake is adjusted properly When the brake is engaged the brake pads should rest solely
39. sing the front tire to blow and go flat If you must stop immediately grab the rear wheels with GLOVED hands The brake is designed for managing safe operation of the racing chair at speeds greater than ten miles per hour Part No 1052767 13 Invacare Top End Eliminator OSR Racing Chair 3 SAFETY WARNING RISK OF INJURY OR DAMAGE TIRE PRESSURE DO NOT use your racing chair unless it has the proper tire pressure p s i DO NOT overinflate the tires Failure to follow these suggestions may cause the tire to explode and cause bodily harm DO NOT ride on a flat or under inflated tires Riding on flat or underinflated tires can cause injury as well as damage to the tire tube and racing chair wheels CARBON FIBER WHEELS ONLY Carbon Fiber Wheels MUST NOT be used when tires are bare or flat If a flat wheel occurs STOP IMMEDIATELY Otherwise the wheel warranty will be void STABILITY AND BALANCE For stability and proper operation of your racing chair you MUST at all times maintain proper balance Turning and cornering affects the stability and balance of the racing chair and user Your racing chair should remain upright and stable during turns and cornering when operated correctly Invacare recommends using positioning strap for additional safety A NOTE TO ASSISTANTS When learning assistance techniques for the racing chair have an experienced assistant help you before attempting it alone When you are assisting with a tra
40. sse 101 A 5310 Mondsee Tel 43 6232 5535 0 Fax 43 6232 5535 4 info invacare austria com www invacare at Portugal Invacare Lda Rua Estrada Velha 949 P 4465 784 Leca do Balio Tel 351 0 225 1059 46 47 Fax 351 0 225 1057 39 portugal invacare com www invacare pt Sverige amp Suomi Invacare AB Fagerstagatan 9 S 163 91 Spanga Tel 46 0 8 761 70 90 Fax 46 0 8 761 81 08 sweden invacare com www invacare se finland invacare com Switzerland Invacare AG Benkenstrasse 260 CH 4108 Witterswil Tel 41 0 61 487 70 80 Fax 41 0 61 487 70 81 switzerland invacare com www invacare ch United Kingdom Invacare Limited Pencoed Technology Park Pencoed Bridgend CF35 5HZ Switchboard Tel 44 0 1656 776200 Fax 44 0 1656 776201 Customer services Tel 44 0 1656 776222 Fax 44 0 1656 776220 UK invacare com www invacare co uk Part No 1052767 2 OVERVIEW 2 Overview 2 Label Location and Component Identification WEIGHT CAPACITY Hooks for UICE Positioning Strap Eliminator OSR Racing Chair with Kneeling Seat design shown REFER TO OWNER S MANUAL Fender and Side Panel pun Rear Wheel dd Front Wheel ompensator Cylinder Track Control Steering Mechanism Front Fork Part No 1052767 9 Invacare Top End Eliminator OSR Racing Chair 2 OVERVIEW 2 2 Typical Product Parameters Upper Inside Frame Width C
41. tery to the desired tautness If the racing chair is equipped with kneeling upholstery attach the foot pouch to the back upholstery and adjust Adjust the back upholstery to the desired tautness TIGHTER upholstery will increase the stability and maintain normal maneuverability of the racing chair because the user is pushed forward in the racing chair slightly LOOSER upholstery will increase the maneuverability and make the racing chair less stable because additional weight is being distributed onto the rear wheels Part No 1052767 33 12 SERVICE PROCEDURES Slots Fastening Flaps Foot Pouch Bottom of Back Attaches Here Upholstery Back Upholstery Cushion Seat Sling Upholstery c Foot Pouch Invacare Top End Eliminator OSR Racing Chair 12 SERVICE PROCEDURES 12 2 Replacing Foot Pouch A WARNING If the racing chair is equipped with kneeling upholstery always ensure the foot pouch is securely latched to the back upholstery Otherwise injury may occur Unlatch three fastening flaps Seat Sling 2 Unlatch the foot pouch from the back upholstery and remove the Upholstery foot pouch 3 Feed the top two fastening flaps between the side guard and racing chair frame and secure together Back Upholstery 4 Adjust the foot pouch to the desired tautness Foot Pouch Fastening Flaps Invacare Top End Eliminator OSR Racing Chair 34 Part No 105276
42. use of a safety lights and reflectors for dusk night riding Give pedestrians the right of way Slow down when turning or cornering otherwise injury or damage may occur Use proper hand signals when turning Slow down at all street intersections and observe to the right to the left and back to right again before proceeding DO NOT attempt to move up or down an incline with an ice or oil film Avoid all surface hazards DO NOT attempt to ride over curbs or obstacles or speed bumps Doing so may cause your racing chair to bottom out and or turn over and cause bodily harm or damage to the racing chair DO NOT attempt to lift the racing chair by any removable detachable parts Lifting by means of any removable detachable parts of an racing chair may result in injury to the user or damage to the racing chair DO NOT stand on the seat or frame of the racing chair DO NOT carry any riders DO NOT carry any items that may obstruct your view or prohibit you from operating the racing chair properly Invacare strongly recommends that the racing chair be boxed or otherwise protected before transporting by an airline carrier WEIGHT LIMITATION The Invacare Eliminator OSR Racing Chair has a weight limitation of 250 Ibs 114 kg BRAKE If necessary adjust the location of the brake on the steering handle for easy access during use NEVER use the brake for immediate stops Using the brake for immediate stops can make the front wheel lock up skid cau
43. ustom Seat Style Standard or Kneel Position Cage Style 1 V Open V or U Cage Lower Inside Seat Width Seat Cage Inside Seat measurement to allow for hip space snug is preferred Axle Position from rear of Racing Chair 5 to 8 inches Seat Height Angle height from floor Rear 16 17 18 or 19 inches Front Standard Position 15 16 17 or 18 inches Kneel Position Seat Angle 10 15 or 20 Overall Length Front Wheel to Rear Wheel 68 to 76 inches Camber to 15 degrees Rear Wheel Size diameter 700C spoked performance Rear Axle diameter 1 5 inch threaded Pushrims diameter Rubber coated 13 to 16 inches Front Wheel Size diameter 20 inches carbon fiber optional Brake Hand Caliper Weight 17 lbs Shipping Weight 27 lbs Standard Equipment Brake Positioning Straps 25 30 35 Tool Kit Allen Tools Pushrims Headset Front Wheel and Side Guards Options see order form Aluminum Knee Plate Aluminum Seat Fixed Footrest Helmet Cordless Speedmeter Additional Straps Cushion Racing Suit Wheel Bag Carbon Fiber Wheel Upgrade Safety Flag Safety Lights Click Straps Alignment Gauge 2 3 Tire Pressure Conversion PSI rating is printed on the side of the tire Conversion formula psi 6 895 kPa approx 7 kPa KILOPASCALS KILOPASCALS KILOPASCALS KILOPASCALS Invacare Top End Eliminator OSR Racing Chair 10 Part No 1052767 3 SAFETY
Download Pdf Manuals
Related Search