User Manual - Witura Technology Sdn Bhd
Contents
1. IMPORTANT Please read through the instruction manual before you start to install and program the device If you are unsure how to connect the device you wish to control please refer to a qualified person Requirements The WT 1011RC requires a 15 volt DC power supply capable of providing a minimum current of 1500mA typical current consumption is 60mMA A mobile phone SIM card with sufficient credit to send confirmation text messages when programming the WT 1011RC unit Note The WT 1011RC identifies only 3V SIM card WT 1011RC IP65 USER MANUAL V2 0 Technical Support technical witura com COPYRIGHT 2013 WITURA TECHNOLOGY SDN BHD And Alarm System Installation Power Switch Insert SIM card here Connect to Battery Back up Install Antenna here Input 15VDC Power here Installing the SIM Card Note Installing the SIM Card Please be sure the initial 4 digit PIN code of SIM card is disabled This can be done by placing it in an unlocked Mobile phone and first checking if the SIM requested any PIN code If this is the case the PIN code can be disabled using the security settings on the l jog Tq Proceed as follows 1 Slide back the SIM door and lift it up 2 Slide the SIM card into the SIM door making sure that the clipped corner of the SIM card lines up with the clipped corner of the SIM holder 3 Close the SIM door 4 Slide the SIM doo2. WT 1011RC IP65 GSM Remote Controller User Manual amp Setting Instructions UNTURA r And Alarm System PACKAGE CONTENTS 1 1 pc IP65 Enclosure 2 1 pc WT 1011RC Main Board with GSM Module mounted 3 1 pc Battery Backup 4 1 pc GSM Antenna leo Introductio usein eene a Ea aE Eaa Na A LA EA Eaa Ta EA Ta 3 2 KERU ER OE E 1 ENE EA A EE A Bag yee Ma 3 3 CharacteriStiC sree pec ceeecencesenses NT ecteensgpeneesnncseeneennne IT Couasesgfesencasensessnenee OT aatar taaa 3 4 Installation INStructiOns cccccccccecccecceeeeceeeeceeeeeeeeceeceeeceseaeseeeseeeseaecaeseeesaeesneeeeeeaesaeeseaeereaas 6 5 WT 1011RC Programming Instructions s essssssssssreiisiiiirsrrsririsrsesrrsrirstaeitrnnnenseerrans 9 5 1 Programming the Administrator Numbers cc cccceeeececseeeceeceeeceeeeeaecaeeeeteeesaeeeseeeeaeeeeenees 9 5 2 Access ControforAdrmiimnistrator Aora ccceceecceeceeeecceeceeeeeeeeceeceeeaecaeseeaesaeseetaeseneeeesetereenees 10 5 3 Programming the Guest List c22 c ccc a Acerca nian Scene ai ea 10 5 4 Output Setting s 5 cecil mnai N eo s iriennet madiin Ae elearen ec Strassen oee 11 5 9 JIPU SENGS oie ees nn ae i a T a ia eaaa E e oaia aaea 15 5 6 Alann Setting Sea A e E a R E ages aE 21 5 7 Miscellaneous SettinGS ccececcceccceceeeeececeseeeeeeaeeeeceeeeaeecaecaeseeesaeeaeceeseeeseseeaesaeseeeeceeeaeeaneeseeeaes 24 5 8 Connection of RS 232 Cable for Programming c ccscccceccesceeces
3. FEATURES More flexible than pager based systems e Low set up and running costs Faster response to alarms and process disturbances e Allows reduced manning levels Increased freedom of movements for users e Reduces wasted traveling time responding to alarm events Provides more detailed information e Easier monitoring of remote process Allows full remote control 3 CHARACTERISTIC WT 1011RC is a versatile SMS alert device suited for most monitoring needs It is simple to use yet is packed with powerful functionalities to meet a wide ranging industrial and commercial and residential applications WT 1011RC IP65 USER MANUAL V2 0 Technical Support technical witura com COPYRIGHT 2013 WITURA TECHNOLOGY SDN BHD olle 1r And Alarm System 3 1 Standalone Operation Housed in the weather and desk proof IP65 enclosure complete with internal industrial modem monitoring controller and flexible operating firmware It is very easy to setup install and use 3 2 2 Digital Inputs Most equipment today does provide some form of alerting signal to interface to monitoring devices from reporting of various malfunction or abnormalities There are various kinds of signal that the equipment can send out most common of which are opening or closure of one or more switch relay contact UPS usually provide signals such as incoming power fail battery mode battery level low and switchover failure An air conditioner system
4. GSM 850 900 1800 1900Mhz Industrial grade modem Its capabilities and performance are highly optimized by the operating firmware Any change in the GSM signal and receiving conditions are detected quickly and automatically takes care of signal errors WT 1011RC IP65 USER MANUAL V2 0 Technical Support technical witura com COPYRIGHT 2013 WITURA TECHNOLOGY SDN BHD troller And Alarm System 3 9 Reliable Performance Besides running the necessary program to perform all the required functions WT 1011RC has diagnostic routines running alongside Being a monitoring device WT 1011RC must have a very high operating reliability and stability Every section of WT 1011RC is monitoring each other Should the modem fail to perform its required role the controller will interrogate and restart the modem 3 10 Application For monitoring and remote control of equipments and machines that are able to provide dry contract signals 2 digital outputs with pulse functions extend control functions Suitable for door access control On Off equipment remotely resetting of Routers Network switches etc Some application examples are Machines Standby Power Generator Electrical Panels Pumps Uninterruptable Power Supplies DC rectifier systems Vending Machines Fire Alarm Panels Gas Monitoring Systems ATM Machines Security Systems Fishery Cold rooms HVAC systems Door Security Network equipment and more 4 INSTALLATION INSTRUCTION
5. WT 1011RC IP65 USER MANUAL V2 0 Technical Support technical witura com 31 COPYRIGHT 2013 WITURA TECHNOLOGY SDN BHD
6. on indefinitely 5 4 1 Reset the Default Latching Time of Relay 1 This command allows you to reset the default latching time of relay To reset the default value you can send the following text command via SMS specifying the number of seconds the output relay 1 should stay on when it is called It is possible to set up to maximum of 65 535 seconds Default 1 second Text Command GOT1 XXXXX XXXXX stands for 5 digits value The number of seconds Example WT 1011RC IP65 USER MANUAL V2 0 Technical Support technical witura com 11 COPYRIGHT 2013 WITURA TECHNOLOGY SDN BHD l A nd Alarm System To set the output relay 1 to stay on for 15 minutes each time it is called you would send the following command to the unit GOT1 00900 Example of Returned Message GOT1 00900 Note When the relay 1 has turned on for 15 minutes and if you wish to turn it off you can send the command RLY1 OFF or RLY1 00000 to the unit If you want the output relay 1 to stay on permanently each time it is called you may send the below command to the unit GOTI1 0ON 5 4 2 Switch On the Output Relay By SMS In addition to the pre programmed latching time when the unit is called it is also possible to temporary or permanently latches the Relay via SMS text message without affecting the existing programming function when the unit is called You can send a text command via SMS specifying the number of seconds the output should stay on
7. relays when calling its number When the system received a phone call from the Guest List it will activate the output relays without answering the call therefore it is free of charge If it is not a registered user of the Guest List the call is rejected and the output relays will never trigger It is possible to program up to 100 phone numbers to be authorized users in the Guest List of the unit and this can be done by sending the following SMS to the unit Text Command WT 1011RC IP65 USER MANUAL V2 0 Technical Support technical witura com 10 COPYRIGHT 2013 WITURA TECHNOLOGY SDN BHD olle r And Alarm System BOOK nnXXXXXXXX nn stands for the position number 00 99 XXXXXXXxX stands for last 8 digits of a phone number Example To program phone number 1234567890 as Guest into the list you would send the following SMS command to the unit BOOK 0034567890 Example of Returned Message WHLOO OK 5 4 OUTPUT Settings The WT 1011RC has 2 outputs that are connected to an on board relay Each output relay can be operated independently By Call Output Relay 1 can be switched ON OFF or switched for a preset time with Caller ID as it can recognize the incoming number if it is an authorized user in the Administrator list it will reject the call without answering and switch on the device connected to it By SMS Output Relay 1 amp 2 can be switched on for a pre determined length of time or switched to stay
8. that does not remain stable for the specified trigger time will be ignored The factory default trigger time is 1 seconds Text Command DLY N XXXXX N stands for Input number 1 2 XXXXxX stands for time in milliseconds Range from 00500ms 65535ms WT 1011RC IP65 USER MANUAL V2 0 Technical Support technical witura com 20 COPYRIGHT 2013 WITURA TECHNOLOGY SDN BHD itroller And Alarm System Example Assume that you want digital input 1 to report when it changes state for more than 500ms you would send the following SMS message to the unit DLY1 00500 5 6 ALARM SETTINGS 5 6 1 Turning the Audible Siren Functions On Off When Inputs Triggered The system has the function to sound the connected audible siren when input triggered This output is available on PIN1 and PIN2 of the connector block To turn On Off this function you can send the following SMS command to the unit Text Command ALM N X N stands for Input number 1 2 X stands for ON 1 or OFF 0 value When ALM1 1 is applied means audible alarm will sound when Input 1 triggered When ALM1 0 Default is applied means audible alarm will not sound when Input 1 triggered 5 6 2 Setting the Alarm Time For Audible Alarm Default 600 seconds The alarm siren can be set to determine how long the siren will remain active and this can be done by sending the following SMS command to the unit Text Command ALTM XXXXX XXXXX s
9. to the unit It is possible to set up to maximum of 65 535 seconds Text Command RLY N XXXXX N stands for output relay number 1 2 XXXXX stands for 5 digits value The number of seconds Example To turn on the output relay number 2 for 1 hour you can send the following text message to the unit RLY2 03600 Example of Returned Message RELAY2 03600 It is also possible to latch the output relay to permanently stay ON you would send the following text message to the unit RLY N ON N stands for output relay number 1 2 WT 1011RC IP65 USER MANUAL V2 0 Technical Support technical witura com 12 COPYRIGHT 2013 WITURA TECHNOLOGY SDN BHD ler And Alarm System Example of Returned Message RELAY2 ON Note Sending the following SMS Message to unit will switch off the relay RLY2 OFF or RLY2 00000 5 4 3 Setting the Recipient of Relay Off Alert The unit can generate text alerts to all 8 administrator s Mobile phone numbers when the relay has turned on or off To set the administrator to receive this alert you would send the following commands by SMS message to the unit Text Command RETR XXXXXXXX X stands for position for 1 8 administrators with function value O OFF 1 9 number of text alerts Example To program the unit to generate 2 SMS to administrators 1 2 3 4 and 5 only you would send the following SMS message to the unit RETR 22222000 Example of Returned M
10. 11RC 15VDC 2W 70mA idle 60mA per active relay 2 Digital protected Inputs 2 Relay Outputs NC 20A 240VAC 28VDC NO 20A 240VAC 28VDC Normally Open Normally Closed amp Common Contacts Dual Band 900 1800Mhz or Quad Band 850 900 1800 1900mhz Less Than 80 RH 0 C to 55 C 130 x 100 x 50 mm 250 Grams Password protected access and phone number checks Remote health check feature via SMS Power Telco Network Signal Low User configurable Screw terminal block Yes WT 1011RC IP65 USER MANUAL V2 0 Technical Support technical witura com 30 COPYRIGHT 2013 WITURA TECHNOLOGY SDN BHD ler And Alarm System WARRANTY Witura Technology Sdn Bhd guarantees all WT 1011RC IP65 GSM Controller against defective parts and workmanship for 1 year warranty Witura Technology Sdn Bhd shall at its option repair or replace the defective equipment upon the return of such equipment to any Witura branch This warranty applies ONLY to defects in components and workman ship and NOT to damage due to causes beyond the control of Witura such as incorrect voltage lightning damage mechanical shock water damage fire damage or damage arising out of abuse and improper application of the equipment Note Wherever possible return only the PCB to Witura Service Centres DO NOT return the enclosure The WT 1011RC IP65 is a product of Witura Technology Sdn Bhd and is manufactured by Shenzhen Witura Telecommunications Co Ltd
11. 161616C151620C031725C021730C011800C0218 02 Note The last 20 events report will be sent only the output relay is on normal function FTRY 1 Make sure the time clock is programmed otherwise the time will not shown correctly 5 7 12 Sound the Audible Alarm Manually It is possible to sound the alarm manually by sending the following SMS command to the unit which remain active for the period of time set Text Command ALNF X X stands for ON 1 or OFF 0 value When ALNF 1 is applied means audible alarm will sound When ALNF 0O Default is applied means audible alarm will turn off 5 8 13 Setting the Password for Reset Command To setup a password for reset command you can send the following SMS command to the unit Text Command PAWO XXXXXX XXXXXxX stands for 6 digits password 123456 Default Example To change the password to 654321 you would send the following SMS command to the unit PAWO 654321 WT 1011RC IP65 USER MANUAL V2 0 Technical Support technical witura com 28 COPYRIGHT 2013 WITURA TECHNOLOGY SDN BHD ler And Alarm System To reset the unit you can send the following SMS command to the unit 5 7 14 Reset the WT 1011RC Text Command REST XXXXXX XXXXXxX stands for 6 digits password based on PAWO Default 123456 and it can be changed anytime 5 7 15 Enable Disable the System To enable all the functions WT 1011RC prepared for work or to disable all the funct
12. A Standard 5V TTL signal will trigger this 7 Ground COM Input 8 Input 1 IN1 A Standard 5V TTL signal will trigger this 9 Ground COM Input 10 NORMALLY OPEN N O OUTPUT RELAY 2 12 NORMALLY CLOSED N C 13 NORMALLY OPEN N O OUTPUT RELAY 1 14 COMMON COM Can be Switched ON OFF by Caller ID or 15 NORMALLY CLOSED N C SMS WT 1011RC IP65 USER MANUAL V2 0 Technical Support technical witura com COPYRIGHT 2013 WITURA TECHNOLOGY SDN BHD zll er And Alarm System IN2 COM INi COM N 12VDC 15VDC 5VDC INPUT 2 INPUT 1 Audible Power Output Alarm Input Output OUTPUT RELAY 2 OUTPUT RELAY 1 5 WT 1011RC PROGRAMMING INSTRUCTIONS via SMS Only You can program the WT 1011RC via SMS commands using your phone Any programming command sent by SMS must be in CAPITAL letters The fields between square brackets are parameters do NOT enter the square brackets When you send a command you will receive the answer for the first time even if your GSM number is not in the administrator list This happens because the WT 1011RC recognizes any GSM number as administrator and answers to it Attention Please program the WT 1011RC unit systematically begin with programming the administrator number 5 1 Programming the Administrator Number The 8 administrator numbers can be programmed with a text command via SMS Text Command TEL N XXXXXXXXXX N stands for administrator number 1 8 XXXXXXXXXX
13. GY SDN BHD oller And Alarm System 5 5 3 Editing the Input Alert Message For When Input gets High Pulse The Input Alert Message can be edited and programmed up to 40 characters long You can change the displayed text by sending the following commands by SMS message to the unit Note Only support normal abc ABC English text no special characters Text Command STR N XXXXxX N stands for number 1 2 of Input XXXXxX stands for the display text that you want to program Example If you want the alert message to display Garage Opened when input 1 triggered you would send the following SMS message to the unit STR1 Garage Opened Example of Returned Message String1 lt Garage Opened gt 5 5 4 Editing the Input Alert Message For When Input returned to Normal The Input Alert Message can be edited and programmed up to 40 characters long You can change the displayed text by sending the following commands by SMS message to the unit Note Only support normal abc ABC English text no special characters Text Command STO N XXXXx N stands for number 1 2 of Input XXXXxX stands for the display text that you want to program Example If you want the alert message to display Garage Closed when input 1 triggered you would send the following SMS message to the unit STO1 Garage Closed Example of Returned Message STRALM1 lt Garage Closed gt WT 1011RC IP65 USER MANUAL
14. HT 2013 WITURA TECHNOLOGY SDN BHD Function 2 e Function as pulse counter Generates a programmable input alert message STR1 once input triggered e Generates a programmable input alert message STO1 once input returned to normal Input 2 Selectable Function Descriptions F2 Function 1 Function as pulse counter Function 2 e Function as pulse counter e Activates the output relay 2 to stay ON e Sends a counter alert message once alarm counter reaches the alert value e Audible alarm will sound if the alarms function is turned on ALM2 1 For more details on function ALM N please refer to Alarm Settings on page Function 3 e Function as pulse counter e Activates the output relay 2 to stay ON Sends a programmable input alert message STR2 once input triggered Audible alarm will sound if the alarms function is turned on ALM2 1 Function 4 Function as pulse counter e Activates the output relay 2 for 2 seconds Sends a programmable input alert message STR2 once input triggered e Audible alarm will sound if the alarms function is turned on ALM2 1 Function 5 Function as pulse counter Activates the output relay 2 with function PWT2 and PWK2 e Sends a programmable input alert message STR2 once input triggered e Audible alarm will sound if the alarms function is turned on ALM2 1 For more details on functions of PWT N and PWK N please refer to Miscellane
15. O OFF 1 9 number of text alerts Example When SIM card has been changed it will generate 3 SMS to administrators 1 2 3 and 1 SMS to the rest you would send the following SMS message to the unit REAT 33311111 Example of Returned Message REAT 33311111 WT 1011RC IP65 USER MANUAL V2 0 Technical Support technical witura com 23 COPYRIGHT 2013 WITURA TECHNOLOGY SDN BHD Controller And Alarm System 5 7 MISCELLANEOUS SETTINGS 5 7 1 Inquire All Programmed Administrator Numbers To check all the administrator number in the list simply send the following SMS command Text Command ADM 5 7 2 Inquire the Status of Inputs To check input status you can send the following SMS command Text Command CTR Input Status Indicator Example 1 Response from WT 1011RC INCTR1 INCTR2 All Inputs are turned off UL Example 2 Response from WT 1011RC INCTR1 ON INCTR2 ON All Inputs are turned on v Example 3 Response from WT 1011RC INCTR1 0FF INCTR2 0FF z Input 1 amp 2 triggered 5 7 3 Inquire the Status of Relay 1 Latching Time To check the status of relay 1 latching time you can send the following SMS command Text Command GOT1 5 7 4 Reading Counter Alert Value Of Inputs It is possible read all the counter alert value of inputs by sending the following SMS command to the unit WT 1011RC IP65 USER MANUAL V2 0 Technical Support tech
16. V2 0 Technical Support technical witura com 17 COPYRIGHT 2013 WITURA TECHNOLOGY SDN BHD olle 1r And Alarm System 5 5 5 Setting the Counter Alert Value For Inputs An alert message will be sent when the increment of alarm counter reaches the alert value Default 500 It is possible to set the alert value up to maximum value of 65 535 times To set the counter alert value of input you can send the following commands by SMS message to the unit Text Command COA N XXXXX N stands for number 1 2 of Input XXXXX stands for 5 digits value The number of times Example Assume that you want it to send a counter alert message each time the input 1 has triggered for 5 times you would send the following SMS message to the unit COA1 00005 Example of Returned Message COA1 00005 5 5 6 Setting the Feature of Input All inputs can be programmed to behave differently it can count the input active high pulses generate an alarm message or activate relay To program the input you can send the following commands by SMS message to the unit Text Command CTCI F1 CTC2 F2 CTC1 stands for input number 1 CTC2 stands for input number 2 Fi stands for selectable input function 1 2 F2 stands for selectable input function 1 8 Input 1 Selectable Function Descriptions F1 Function 1 Function as pulse counter WT 1011RC IP65 USER MANUAL V2 0 Technical Support technical witura com 18 COPYRIG
17. al strength 0 31 you would send the following SMS command to the unit Text Command CSQ 5 7 10 Checking the Serial IMEI Number of WT 1011RC Device To check the serial IMEI number you would send the following SMS command to the unit Text Command SERIE 5 7 11 Setting the Recipient of Last Contact Call This function allows you to receive a list of last 20 events of the Guest users who operate the output relay 1 When all selected the system can generate a list with last 20 events to all 8 administrators To enable the administrator to receive this list you would send the following commands by SMS message to the unit Text Command FULL XXXXXXX X stands for position for 1 8 administrators with function value O OFF 1 ON Example To enable administrators 1 2 and 3 to receive the list of last 20 events you would send the following SMS message to the unit FULL 11100000 Format of Last Contact Call LACC Txxhhmm T stands for the type of access where S stands for SMS C stands for CALL xx stands for the position of the authorized user hh stands for hour mm stands for minute WT 1011RC IP65 USER MANUAL V2 0 Technical Support technical witura com 27 COPYRIGHT 2013 WITURA TECHNOLOGY SDN BHD oller And Alarm System Example of last 20 events received by SMS LACC C011102S032012C302050C352315C252359C870015C140056C260615C2 70815830 0925S021015C301130C351520C251615S
18. an be activated by text messages from mobile phone Creating action messages are done with the same ease as that of input monitoring 3 4 Querying Inputs And Outputs Status Authorized groups can also query the status of an input or output This is very useful feature to determine the present status of an input or output The enquirer need not wait for an alarm to happen in order to receive the given I O status 3 5 Turning On Off Device Remotely Authorized users can send a SMS command to trigger on or off the digital output Upon receiving the command WT 1011RC will perform the instructed action After the on or off action is done it will send a reply to the querying mobile phone as an acknowledgement 3 6 Remote Editing Of Mobile Phone Numbers WT 1011RC has a feature to allow user to remotely add change or delete any mobile phone numbers in WT 1011RC memory Re assigning of operation personnel a change of mobiles phone number is also common Rather than having to physically go to the installation site with a notebook computer the authorized personnel can perform the change from anywhere using mobile phone Where there are many installed sites this feature saves time and afford 3 7 System Check Authorized mobile phone group can perform system check by sending a command to WT 1011RC If WT 1011RC is switched on or working normally it will reply to the querying number 3 8 GSM Modem Integral to the design of WT 1011RC is a
19. and 1 SMS to the rest when AC failure you would send the following SMS message to the unit REAC 22211111 Example of Returned Message REAC 22211111 WT 1011RC IP65 USER MANUAL V2 0 Technical Support technical witura com 22 COPYRIGHT 2013 WITURA TECHNOLOGY SDN BHD oller And Alarm System 5 6 5 Anti Theft Feature The system has an anti theft function that can used to detect the person who hijacks the WT 1011RC device It allows the owner to identify the hijacker s SIM Card number by sending a warning message to the programmed owner s number when the SIM card has been switched To activate and also deactivate this function you can send the following SMS command to the unit Text Command ANTH X X stands for ON 1 or OFF 0 value When ANTH 1 is applied means it will alert the owner by sending a warning message when the SIM Card has been changed When ANTH 0O Default is applied means this function is turned off Alert message received WARNING SIM Card Has Been Changed On WT 1011RC 5 6 6 Setting the Recipient of Anti Theft Alert With Anti Theft function turned on it can generate text alerts to all 8 of the administrator s Mobile phone numbers whenever the SIM card has changed To set the administrator to receive this alert you would send the following commands by SMS message to the unit Text Command REAT XXXXXXXX X stands for position for 1 8 administrators with function value
20. eeeeeeeeeceeeseeeeeeeesaeeeneastaeeaeees 29 6 Fechnical Spechficath om Smeer heee ea R pee We ereeP ET anao FRR 30 WT 1011RC IP65 USER MANUAL V2 0 Technical Support technical witura com COPYRIGHT 2013 WITURA TECHNOLOGY SDN BHD olle 1r And Alarm System INTRODUCTION WITURA WT 1011RC GSM Remote Controller and Alarm System allow you to use your mobile phone to monitor and control your business from any location Its alarm facilities provide a flexible way to distribute critical alarm information to any number of mobile phone users WT 1011RC provides detailed alarm messages secure alarm acceptance full alarm reporting and even remote process control This allows user to rectify problems directly via their mobile phone within minutes of the alarm occurring The WT 1011RC can monitor 2 digital inputs A SMS alarm message can be sent when inputs triggered The user can also interrogate the inputs through SMS messaging The WT 1011RC also has 2 heavy duty relay outputs can be used to switch on any application like lamps pumps heaters etc Output Relay 1 can be switched ON or OFF by calling its cell phone number or by sending an SMS command there is no call charges incurred when dialing the unit as it will recognize an authorized telephone number calling it and reject the call without answering Output Relay 2 can be programmed to switch on for a pre determined length of time by sending the WT 1011RC a text command 2
21. essage RETR 22222000 5 4 4 Follow function for Output Relays This function allows the second relay to latch at a specific time GOTX later after the first relay has latched and when the first relay has switched off the second relay will switch off after a specific time GOTY Text Command to Enable this Function FTRY 2 Text Command to Enable the normal Function FTRY 1 WT 1011RC IP65 USER MANUAL V2 0 Technical Support technical witura com 13 COPYRIGHT 2013 WITURA TECHNOLOGY SDN BHD And Alarm System ller Example To program the device so that when you latched relay 1 relay 2 will latch 5 seconds GOTX later GOTX 00005 Example of Returned Message GOTX 00005 Example To program the device so that when the relay 1 closes relay 2 will closes 10 seconds GOTY later GOTY 00010 Example of Returned Message GOTY 00010 Note When using this function the GOTX delay time value you programmed must be smaller than the latching time of output relay 1 GOT1 otherwise the system will return an error message 5 4 5 Setting the Operating Time for Output Relay 2 The output relay 2 can be programmed to operate at a programmable time To program this function you can send the following commands by SMS message to the unit Text Command to Enable this Function FTRY 3 Note When this function enabled functions related to activation of output relay 2 will be disabled and act
22. ions WT 1011RC is not prepared for work you can send the following SMS command to the unit Text Command for Enable the System ENABLE Returned Message ENABLE Text Command for Disable the System DISABLE Returned Message DISABLE 5 7 16 Auto Restart System The WT 1011RC can continuously monitor the system status of its own When there is a problem with system operation or the module is not working properly it will restart the system automatically to avoid the unit stopped working permanently If the system failed to respond within 15 30 seconds it will restart the system 5 8 Connection of RS 232 Cable for Programming The WT 1011RC can be program with the provided programmer software To do so the WT 1011RC unit must be turned on and connected to the computer s COM port with the provided RS 232 cable as shown below WT 1011RC IP65 USER MANUAL V2 0 Technical Support technical witura com 29 COPYRIGHT 2013 WITURA TECHNOLOGY SDN BHD For software programming details please refer to the WT 1011RC Programmer Guide 6 TECHNICAL SPECIFICATIONS Item Model Operating Voltage Current Consumption No of Inputs No of Outputs Relay Contact Capacity Relay Connections Communication Port GSM Modem Humidity Operating Temperature Physical size Weight Security Features System Health Check Indicators Repeat SMS of alarms I O Interface Output pulse capability Description WT 10
23. ivation of output relay 2 via SMS will be rejected Text Command to Enable the normal Function FTRY 1 Text Command to set the time TSET SS MM HH HH hours MM minutes and SS seconds Example Assume it is 8 30am you would send following SMS message to the unit TSET 00 30 08 WT 1011RC IP65 USER MANUAL V2 0 Technical Support technical witura com 14 COPYRIGHT 2013 WITURA TECHNOLOGY SDN BHD ler And Alarm System Text Command to set the Operating time for the outputs SMW SS MM HH TTTTT G R HH hours 2 digits MM minutes 2 digits SS seconds 2 digits TTTTT turn on time in seconds 5 digits G group number 1 8 R 2 relay 2 Examplei Assume you want output relay 2 to turn on for 30 seconds on 5 30pm you would send following SMS message to the unit SMW 00 30 17 00030 1 2 Example of Returned Message SMW 00 30 17 00030 1 2 5 5 INPUT SETTINGS One of the most important functions of WT 1011RC is to receive alarms In order to use this function you must turn on the function of the inputs and tell the WT 1011RC which are the recipient numbers and who should receive the alert message for the particular input 5 5 1 Turn On the Function of Inputs To turn on the function of input you can send the following commands by SMS message to the unit Text Command CTR N X N stands for number 1 2 of Input X stands for ON 1 or OFF 0 value Example To tu
24. may provide signals such as system on off compressor over temperature low gas pressure etc Equipments to be monitored are connected to WT 1011RC using these alarm signaling contacts WT 1011RC keeps a constant watch over all the contacts Whenever any contact input changes status either from a close to open or from an open state to close state it is captured by WT 1011RC It will then process the input according to the configuration provided by the user The correct SMS messages will be sent to 8 mobile phone users WT 1011RC is so fast in capturing the change of status of any signaling contacts that no event will be missed out up to 2 inputs can be monitored directly The flexibility of WT 1011RC is in allowing remote query of input status using SMS To change contacting mobile phone number is also very easy Authorize personal remotely using SMS command to add change or delete mobile phone number in WT 1011RC 3 3 2 Digital Outputs WT 1011RC is a 2 way device Besides monitoring inputs and act upon such inputs it also allow mobile phone users to compose SMS messages to it When WT 1011RC receives any SMS it will look its memory bank to see what it is supposed to do and action according No action SMS are ignored WT 1011RC IP65 USER MANUAL V2 0 Technical Support technical witura com COPYRIGHT 2013 WITURA TECHNOLOGY SDN BHD oller And Alarm System Relay 1 can turned on and off by calling its number and Relay 2 c
25. nical witura com 24 COPYRIGHT 2013 WITURA TECHNOLOGY SDN BHD oller And Alarm System Send the following SMS Command COA 5 7 5 Reading the Total Increment Counter Value To read the total increment counter value you can send the following SMS message to the unit Text Command COU Example of Returned Message INC1 00000 0 INC2 00000 0 How Total Increment Counter Works When the counter alert value for input 1 has been programmed at 50 times COA1 00050 It means when Input 1 alarm counter reaches 50 times the TOTAL counter will increase 1 INC1 00001 0 and then if alarm counter reaches 100 times then the TOTAL counter will be 2 INC1 00002 0 When the counter alert value for input 1 has been programmed at 100 times COA1 00100 It means when Input 1 alarm counter reaches 100 times the TOTAL counter will increase 1 INC1 00001 0 and then if alarm counter reaches 200 times then the TOTAL counter will be 2 INC1 00002 0 5 7 6 Reading the Sub Increment Counter Value To read the sub increment counter value you can send the following SMS message to the unit Text Command COT Note The sub increment counter value will be reset automatically each time the alarm counter reached the alert value WT 1011RC IP65 USER MANUAL V2 0 Technical Support technical witura com 25 COPYRIGHT 2013 WITURA TECHNOLOGY SDN BHD oller And Alarm System 5 7 7 Reset the Total Incremen
26. ous Settings on page WT 1011RC IP65 USER MANUAL V2 0 Technical Support technical witura com 19 COPYRIGHT 2013 WITURA TECHNOLOGY SDN BHD And Alarm System Function 6 Function as pulse counter e Activates the output relay 2 with function PWT2 and PWK2 e Audible alarm will sound if the alarms function is turned on ALM2 1 Function 7 Function as pulse counter e Sends a programmable input alert message STR2 once input triggered Audible alarm will sound if the alarms function is turned on ALM2 1 Function 8 e Function as pulse counter Sends a programmable input alert message STR2 once input triggered Sends a programmable input alert message STO2 once input returned to normal e Audible alarm will sound if the alarms function is turned on ALM2 1 Example Assume that you want to use input 1 for pulse counter only you would send the following SMS message to the unit CTC1I 1 Example of Returned Message CTC1 lt 1 gt Note Only Input 1 may apply function F1 where only 2 selectable functions available Only Input 2 may apply function F2 where 8 selectable functions are available 5 5 7 Setting the Input Trigger Delay Time The unit will report the state of all inputs when any input changes state for longer than a programmable trigger time The trigger time of each alarm input is programmable and can be varied from a minimum of 500ms to a maximum of 65535ms Any change
27. r to lock the SIM card in place Power Up the Device Connect a 15 volt DC power supply to terminal 3 amp 4 ensuring positive is connected to terminal 3 switch on the power supply the power LED will lit indicating power is present the network LED indicator will initially flash quickly once logged onto the network it will flash more slowly approximately every 3 to 4 seconds Note You should install the WT 1011RC in a place where there is GSM signal coming from the operator you want to use Check it with a phone before proceeding with the installation If you need to install the device in a place with little signal you may consider using an external antenna that we may supply as an option to be purchased separately with 5m cable WT 1011RC IP65 USER MANUAL V2 0 Technical Support technical witura com COPYRIGHT 2013 WITURA TECHNOLOGY SDN BHD larm System Connection Details If you are unsure how to connect the device you wish to control please refer to a qualified person IN2 COM INi COM NO c NC NO c NC 12VDC 15VDC 5VDC INPUT 2 INPUT 1 Audible Power Output Alarm Input Output OUTPUT RELAY 2 OUTPUT RELAY 1 Port Descriptions 1 12 volts DC Output Audible Alarm Output 2 12 volts DC Output 3 15 volts DC Input a 15 volts DC power that capable of 4 15 volts DC providing a current of 1 5 Amp 5 5 volts DC output Auxiliary 5 volts DC Output can be used to trigger the inputs 6 Input 2 IN2
28. rn on input number 1 you can send the following text message to the unit CTRI 1 Returned Message WT 1011RC IP65 USER MANUAL V2 0 Technical Support technical witura com 15 COPYRIGHT 2013 WITURA TECHNOLOGY SDN BHD INCTRI ON Sending the following SMS Message to unit would mean input 1 will be turned off CTR1I 0 Returned Message INCTR1 OFF The 1 indicates the ON command and the O zero indicates the OFF command 5 5 2 Setting the Alert Message Recipients Every input can generate text alerts to all 8 administrator s Mobile phone numbers and this function can be changed at any time by sending the following commands by SMS message to the unit Text Command RER N XXXXXXXX N stands for input number 1 2 X stands for position for 1 8 administrators with function value O OFF 1 9 number of text alerts Example 1 Any alarm coming from Input 1 will generate 2 SMS to administrators 1 2 3 and 1 SMS to the rest you would send the following SMS message to the unit RER1 22211111 Example of Returned Message RER1 22211111 Example 2 Any alarm coming from Input 2 will generate 3 SMS to administrator 1 2 SMS to administrator 2 3 4 and 5 no SMS to the rest you would send the following SMS message to the unit RER2 32222000 Example of Returned Message RER2 32222000 WT 1011RC IP65 USER MANUAL V2 0 Technical Support technical witura com 16 COPYRIGHT 2013 WITURA TECHNOLO
29. stands for the phone number you want to program as administrator WT 1011RC IP65 USER MANUAL V2 0 Technical Support technical witura com COPYRIGHT 2013 WITURA TECHNOLOGY SDN BHD r And Alarm System Please note that it is possible to program up to a maximum of 16 digits for a phone number Example To program phone number 1111222233 as administrator into list number 1 you would send the following SMS command to the unit TEL1 1111222233 After sending the above command the WT 1011RC will reply a message back to you that the administrator number has been added Example of Returned Message TEL1 1111222233 5 2 Access Control For Administrators Note It is advised that the owner should set the system to allow programming access and remote control of Output Relay 1 for administrators only after programming the Administrator numbers Sending SMS Command ANY 1 Only the administrators in the list will have the authority to access the system and remote control of Output Relay 1 by calling its number any person outside the list in this case will not have the authority to access the system and text command sent to the system will be rejected To allow any person gain access to the system just send SMS Command ANY 0 Note Only Administrator number 1 and 2 may send this SMS command 5 3 Programming the Guest List The system allows the phone numbers in the Guest List as authorized user to operate the output
30. t Counter Value To reset the total counter value you can send the following SMS message to the unit Text Command CLA N N stands for Input number 1 2 Example When CLA1 is sent means the total increment counter value will be reset 5 7 8 Setting the Function of Opening amp Closing time for Output Relay The system has the function to activate the relay for a specific time and then be deactivated for a specific time in a repeating process To set the opening amp closing time of the relays you can send the following SMS command to the unit Note This function only applied in F2 selectable input function 5 and 6 Text Command for Opening time PWT2 XXXXX XXXXX stands for 5 digits value The number of seconds Text Command for Closing time PWK2 XXXXX XXXXX stands for 5 digits value The number of seconds Example Opening time of output 2 is set as 1 minute PWT2 00060 and the Closing time as 5 seconds PWK2 00005 and function 5 is applied on Input 2 When input 2 triggered output relay 2 will be activated for 1 minute and close for 5 seconds and then back on for 1 minute and close again for 5 seconds and will keep on repeating the process until the command RLY2 00000 is issued WT 1011RC IP65 USER MANUAL V2 0 Technical Support technical witura com 26 COPYRIGHT 2013 WITURA TECHNOLOGY SDN BHD oller And Alarm System TUN 5 7 9 Checking Signal Strength To check the sign
31. tands for 5 digits value The number of seconds 00000 65535 Example When ALTM 03600 is applied means the audible alarm will sound for 1 hour when triggered WT 1011RC IP65 USER MANUAL V2 0 Technical Support technical witura com 21 COPYRIGHT 2013 WITURA TECHNOLOGY SDN BHD oller And Alarm System 5 6 3 Power Down Alarm The system has the function to send a text alert in the event the main power is lost and the system is relying on battery back up It is also possible to activate and deactivate this function by sending the unit an SMS Message Text Command ALAC X X stands for ON 1 or OFF 0 value When ever the ALAC 1 command is activated and the power down alarm is on any of the Administrators programmed to receive text alerts will receive the following messages from the unit in the event of power down and also when power is restored Power down and text alert received ACP OFF Power restored and text alert received ACP ON 5 6 4 Setting the Recipient of AC Failure Alert Whenever there is power failure the unit can generate text alerts to all 8 administrator s Mobile phone numbers To set the administrator to receive this alert you would send the following commands by SMS message to the unit Text Command REAC XXXXXXXX X stands for position for 1 8 administrators with function value O OFF 1 9 number of text alerts Example To generate 2 SMS to administrators 1 2 3
Download Pdf Manuals
Related Search