HN-DR4PN2U
Contents
1. User Name Username provided by your 3G ISP Password Password provided by your 3G ISP Authentication Method Select a proper authentication method in the drop down list You can select Auto PAP CHAP or MSCHAP APN APN Access Point Name is used to identify the service type Enter the APN provided by your 3G ISP Dial Number Enter the dial number provided by your 3G ISP Idle time in sec If no traffic for the preset time the 3G will disconnect automatically 14 HN DR4PN2U User Manual Default WAN Connection Select You can select DSL or ETHERNET or 3G from the drop down list WAN back mechanism The 3G connection is backup for the DSL connection DSL If the DSL is disconnected the 3G starts to dial IP connectivity If the system fails to ping the specified IP address the 3G starts to dial After finishing setting click the Apply Save button to save the settings You may also click the auto setting button to automatically configure the 3G connection Click Apply Save to apply the settings 152. 3 Plug one end of the power adapter to the wall outlet and connect the other end to the Power interface of the router The following figure shows the connection of the Router PC and telephones HN DR4PN2U User Manual ADSL _____LAN1 LAN2 LAN3 LAN4 USB Power SE Splitter feon DSL Service e Line RJ45 Power Phone a Socket 4 introduction to Web Configuration 4 1 Preparation before Login Before accessing the Modem ensure the communication between PC and Modem is normal Check the communication as follows Configure the IP address of the PC as 192 168 1 X 2 254 net mask as 255 255 255 0 gateway address as 192 168 1 1 For customized version configure them according to the actual version Enter arp a in the DOS window to check whether the PC can read the MAC address of the Modem les e WINNT system32 cmd exe Microsoft Windows 2000 Version 5 00 2195 C Copyright 1985 2000 Microsoft Corp C Documents and Settings Administrator gt arp a Interface 10 61 86 f7 on Interface 0x1000003 Internet Address Physical Address Type 10 61 84 86 00 00 39 b5 67 2c dynamic 10 61 84 165 00 cO df b3 1c 04 dynamic 10 61 87 254 00 0a 8a 99 b2 00 dynamic Documents and Settings Administrator gt Ping the management IP address 192 168 1 1 by default of the Modem HN DR4PN2U User Manual If the PC can read the MAC address of the Modem and can ping through the management IP addre
3. This screen allows you to configure an ETH port Select an ETH port LANA w Select Connection Mode Default Mode Single service over one connection VLAN MUX Mode Multiple Vlan service over one connection Figure 4 ETH WAN Configuration In this page you can select an ETH port from the drop down list and select Default Mode or VLAN MUX Mode as the connection mode 4 3 2 WAN Service Choose Advance Setup gt WAN Service and the following page appears Wide Area Network WAN Service Setup Choose Add Remove or Edit to configure a WAN service over a selected interface Interface Description Type Vlang021p VianMuxid Igmp NAT Firewall IPv6 Mid Remove Edit pppo pppoe_0_0_35 PPPoE N A N A Disabled Enabled Enabled Disabled Disabled Fl pppoal pppoa_0_7_70 PPPoA N A N A Disabled Enabled Enabled Disabled Disabled Fi eai ppp2 l pppoe_0_8_35 PPPoE N A N A Disabled Enabled Enabled Disabled Disabled Fj ppp3 pppoe_0_0_32 PPPoE N A N A Disabled Enabled Enabled Disabled Disabled F ppp4 pppoe_0_8_81 PPPoE N A N A Disabled Enabled Enabled Disabled Disabled Fi ppp5 pppoe_0_0_33 PPPoE N A N A Disabled Enabled Enabled Disabled Disabled F Figure 5 WAN service configuration In this page you are allowed to add remove or edit a WAN service HN DR4PN2U User Manual Adding a PPPoE WAN Service This section describes
4. of the common user are user and user You need not enter the username and password again if you select the option Remember my password It is recommended to change these default values after logging in to the DSL router for the first time Click OK to log in to the Web page Otherwise please click Cancel to exit HN DR4PN2U User Manual OSL Router User name f admin Password After logging in to the DSL router as a super user you can view configure and modify all the settings and diagnose the system 4 3 WAN Configuration 4 3 1 Layer2 Interface ATM Interface Choose Advanced Setup gt Layer2 Interface gt ATM Interface and the following page appears DSL ATM Interface Configuration Choose Add or Remove to configure DSL ATM interfaces Quick Setup DSL Link Connection Scheduler Queue Group 7 Interf Vpi Vci Cat Ri Device Info special tea ie Latency al Type Mode Alg Weight Precedence irt Advanced Setup Layer2 Interface 3 atm0 0 35 Patho UBR EoA DefaultMode Enabled SP 1 8 Fi Ae atmi 7 70 Patho UBR PPPoA DefaultMode Enabled SP 1 8 o ETH Interface WAN Service atm2 8 35 Patho UBR EoA DefaultMode Enabled SP 1 8 oO 3G Wan Service LAN atm3 0 32 Patho UBR EoA DefaultMode Enabled SP 1 8 oO NAT s atm4 8 81 Patho UBR EoA DefaultMode Enabled SP 1 8 oO Security Parental Control atm5 0 33 Patho UBR EoA DefaultMode Enabled SP 1 8 Fi Quality of S
5. ATM network ranging from 32 to 65535 1 to 31 are reserved for known protocols Select DSL Latency You may select PathO and Path Select DSL Link Type You may select EoA it is for PPPoE IPoE and Bridge PPPOA or IPoA Select Connection Mode You may select the Default Mode or the VLAN MUX Mode HN DR4PN2U User Manual Encapsulation Mode You may select LLC SNAP BRIDGING or VC MUX in the drop down list e Service Category you may select UBR Without PCR UBR With PCR CBR Non Realtime VBR or Realtime VBR in the drop down Isit Select IP QoS Scheduler Algorithm You may select Strict Priority and Weighted Fair Queuing Note QoS cannot be set for CBR and Realtime VBR After finishing setting click the Apply Save button to make the settings take effect See the following figure If you want to remove this Interface please select the Remove check box that is corresponding to the selected interface and then click the Remove button ETH Interface Choose Advanced Setup gt Layer2 Interface gt ETH Interface and the following page appears ETH WAN Interface Configuration Choose Add or Remove to configure ETH WAN interfaces Allow one ETH as layer 2 wan interface Interface Name Connection Mode Remove Add Figure 3 ETH WAN Interface Configuration In this page you can add or remove the ETH WAN Interfaces Click the Add button to display the following page HN DR4PN2U User Manual ETH WAN Configuration
6. Driver This page is used to configure 3G connection If you want to access the Internet through 3G connection a 3G network card is required Connect the 3G network card to the USB interface of the Router Information Click it to display the information of the 3G network card e Upload Driver For a un support USB dongle click it to upload the new driver for supporting the USB The driver is a text file Click Add in the WAN Service For 3G Moblie Setup to display the following page 13 HN DR4PN2U User Manual 3G USB mobile modem setup Initialization Delay and Mode Switch Delay are used to setting the delay time before initializing a 3G dongle if the value of them is small the initializating will be fast but will result in some 3G dongle being not recognized C Enable USB Modem any User Name Password eco Authentication AUTO Method APN Dial Number Idle timefin a 7 i gt 360 sec Net Select AUTO go Dial on demand Initialization 7 Delay in 20 sec Mode Switch Delay in 20 sec Dial Delay in f 10 sec L Default WAN Connection DSL OR ETHERNET Select i WAN backup mechanism DSL O PP connectivity Apply Save Auto Setting In this page you are allowed to configure the settings of the 3G USB modem Enable USB Modem If you want to access the Internet through the 3G network card you must enable the USB modem
7. E The device is powered off Ons The DSL line connection is established Green Blink ee The DSL line is off Blink Blink quickly The DSL line is initiating The Internet connection is established Green And the users can access the Internet Blink Internet data is being transmitted Internet Re On Authentication fails Of The device is not connected to the Internet The Ethernet interface is connected LAN4 1 Greeni Bini Data is peg transmitted through the Ethernet interface OF _ The Ethernet interece ts disconnected The Ethernet interface is disconnected On WLAN is WLAN is enabled Data is being transmitted through the Green Blink Wireless interface Off WLAN is disabled Connection succeeds under Wi Fi Green Protected Setup HN DR4PN2U User Manual LEDs Color Status Description _ Se Protected Setup Wi Fi Protected Setup is disabled Data is being transmitted Of The connection of 3G or USB flash disk is disabled 2 1 2 Rear Panel WPS ht r eo J O iag WLAN Reset ADSL LAN1 LAN2 LAN4 USB Power _ a is Na _ LAN3 On The connection of 3G or USB flash disk has established USB Green me _ ees The following table describes the interfaces of the device If you press the button between 1s and 5s to enable WLAN WPS WLAN function Press the button for more than 5s to enable WPS function splitter through a t
8. HN DR4PN2U User Manual HN DR4PN2U User Manual Contents Salely PRECAUUONS oren r 1 NIGP OG UIC TOMA emain a ea eo ays eee aan ea aoa eoee ents 1 2 1 LED Slaius DESCrip lon izcsascitee ial re eee 2 2E Front Prane scsi sant notre aac acc eae aon a sagas sean ae 2 22 ROGAN ANG lecyeceosets eset seee alae EOE 3 Hardware Installation sicr eaae a a a TEER 1 3 1 Choosing the Best Location for Wireless Operation ccceceeeeee 1 3 2 Connecting the ADSL Router cccccecccesssssececeeseeesseseeeessesseeessenees 1 Introduction to Web Configuration ccccccecececseeeeeeeeeeeeeeeeeeeeeseeeeeeeseeeeeeesaaees 2 4 1 Pr paration before LOGIN sy crescxenasosatourteanniiwiarantanreiaweawauinntboaypercieds 2 4 2 Logging In to the ROUter cccccccssssesecseeeseeeseesseesseeseeesseseesseaseeesees 3 4 3 WAN Configuratio sicississcis sixrepnientcereciebreeen abainediainddenseinawinasdubeorsanaminnidenttn 4 4 3 1 Layer2 INtSMAaCe ecsscciesge sei sutercci wired cnet eceneegeausecseec seuss 4 432 WAN O NCO a A re era raa A T A3 3 SG AANI ATE E e E eet ee eee ies 13 HN DR4PN2U User Manual 1 Safety Precautions Follow the instructions below to prevent damage to the device and the risk of fire or electric shock Use the power adapter supplied with the unit and plug it into a suitably rated power outlet Leave sufficient space around the Power adapter and Modem to allow the free flow of air fo
9. bnormal PPP IP extension If you want to configure DMZ Host you should enable it first Use Static IPv4 Address If this function is disabled the modem obtains an IP address assigned by an uplink equipment such as BAS through PPPoE dial up If this function is enabled the modem uses this IP address as the WAN IP address Enable PPP Debug Mode Enable or disable this function Bridge PPPoE Frames Between WAN and Local Ports Enable or disable this function Enable IGMP Multicast Proxy if you want PPPoE mode to support IPTV enable it Step5 After setting the parameters click Next to display the following page 10 HN DR4PN2U User Manual Routing Default Gateway Default gateway interface list can have multiple WAN interfaces served as system default gateways but only one will be used according to the priority with the first being the higest and the last one the lowest priority if the WAN interface is connected Priority order can be changed by removing all and adding them back in again Selected Default Available Routed WAN Gateway Interfaces Interfaces ppp Figure 9 Routing default gateway PPPoE Step6 In this page select a preferred WAN interface as the system default gateway and then click Next to display the following page DNS Server Configuration Select DNS Server Interface from available WAN interfaces OR enter static DNS server IP addresses for the system In ATM mode if only a single PVC w
10. e boxes below enter the user name and password that your ISP has provided to you PPP Username PPP Password PPPoE Service Name Authentication Method AUTO v E Enable Fullcone NAT Dial on demand with idle timeout timer PPP IP extension Use Static IPv4 Address Enable PPP Debug Mode m a Bridge PPPoE Frames Between WAN and Local Ports Multicast Proxy C Enable IGMP Multicast Proxy Figure 8 PPP username and password PPPoE HN DR4PN2U User Manual Step4 In this page you can modify the PPP username PPP password PPPoE service name and authentication method PPP Username The correct user name provided by your ISP PPP Password The correct password provided by your ISP PPPoE Service Name If your ISP provides it to you please enter it If not do not enter any information Authentication Method The value can be AUTO PAP CHAP or MSCHAP Usually you can select AUTO Dial on demand with idle timeout timer If this function is enabled you need to enter the idle timeout time Within the preset minutes if the modem does not detect the flow of the user continuously the modem automatically stops the PPPOE connection Once it detects the flow like access to a webpage the modem restarts the PPPoE dialup If this function is disabled the modem performs PPPoE dial up all the time The PPPoE connnection does not stop unless the modem is powered off and DSLAM or uplink equipment is a
11. elephone cable PC or the Ethernet devices through an Ethernet cable storage devices output of power adapter is 12 V DC 1A Power switch To restore the factory default keep the device powered on Reset push a needle into the hole for about 1 second and then release HN DR4PN2U User Manual 3 Hardware Installation 3 1 Choosing the Best Location for Wireless Operation Keep the numbers of walls and ceilings to the minimum Consider the direct line between access points and workstations Building materials make difference Position the antenna for best reception Keep your product away at least 1 2 meters from electrical devices Keep wireless devices away from electrical devices that generate RF noise such as microwave ovens monitors and electric motors 3 2 Connecting the ADSL Router Step 1 Connect the ADSL interface of the router to the MODEM interface of the splitter through a telephone cable Connect the phone to the PHONE interface of the splitter through a cable Connect the incoming line to the LINE interface of the splitter The splitter has three interfaces LINE Connect to a wall phone jack RJ 11 jack MODEM Connect to the ADSL jack of the device PHONE Connect to a telephone set Step2 Connect the LAN interface of the router to the network interface card NIC of the PC through an Ethernet cable MDI MDIX Note Use the twisted pair cables to connect with the hub or switch Step
12. ervice DNS Figure 1 DSL ATM interface configuration In this page you can add or remove the DSL ATM Interfaces Click the Add button to display the following page 4 HN DR4PN2U User Manual ATM PVC Configuration This screen allows you to configure an ATM PVC identifier VPI and VCI select DSL latency select a service category Otherwise choose an existing interface by selecting the checkbox to enable it VPI 0 255 o VCI 32 65535 40 Select DSL Link Type EoA is for PPPoE IPoE and Bridge EoA PPPoA O IPoA Ww elect Connection Mode Default Mode Single service over one connection O VLAN MUX Mode Multiple Vian service over one connection Encapsulation Mode LLC SNAP BRIDGING v Service Category UBR Without PCR w Select IP QoS Scheduler Algorithm Strict Priority Precedence of the default queue 8 lowest Weighted Fair Queuing Weight Value of the default queue 1 63 p MPAAL Group Precedence 8 y Figure 2 ATM PVC configuration In this page you can set the VPI and VCI values and select the DSL latency link type EoA is for PPPoE IPoE and Bridge connection mode encapsulation mode service category and IP QoS scheduler algorithm VPI Virtual Path Identifier The virtual path between two points in an ATM network and its valid value is from 0 to 255 VCI Virtual Channel Identifier The virtual channel between two points in an
13. ith IPoA or static IPoE protocol is configured Static DNS server IP addresses must be entered DNS Server Interfaces can have multiple WAN interfaces served as system dns servers but only one will be used according to the priority with the first being the higest and the last one the lowest priority if the WAN interface is connected Priority order can be changed by removing all and adding them back in again Select DNS Server Interface from available WAN interfaces Selected DNS Server ae Available WAN Interfaces pppo ppp Figure 10 DNS server configuration PPPoE Step7 In this page you may obtain the DNS server addresses from the selected WAN interface or manually enter the static DNS server addresses If only a PVC with IPoA or static MER protocol is configured you must manually 1 HN DR4PN2U User Manual enter the static DNS server addresses Click Next and the following page appears WAN Setup Summary Make sure that the settings below match the settings provided by your ISP Connection Type PPPoE NAT Enabled Ful Cone NAT Disabled Firewall Enabled IGMP Multicast Disabled Quality Of Service Enabled Click Apply Save to have this interface to be effective Click Back to make any modifications Figure 11 PPPoE summary Step8 In this page it displays the information about the PPPoE settngs Click Apply Save to save and apply the settings and then the f
14. ollowing page appears You can modify the settings by clicking the Back button if necessary Wide Area Network WAN Service Setup Choose Add Remove or Edit to configure a WAN service over a selected interface Interface Description Type Vlan8021p VlanMux d Igmp NAT Firewall IPv6 Mid Remove Edit pppo pppoe_0_0_35 PPPoE N A N A Disabled Enabled Enabled Disabled Disabled Fi pppoal pppoa_0_7_70 PPPoA N A N A Disabled Enabled Enabled Disabled Disabled Fj ea ppp2 pppoe_0_8_35 PPPoE N A N A Disabled Enabled Enabled Disabled Disabled Boo ppp3 pppoe_0_0_32 PPPoE N A N A Disabled Enabled Enabled Disabled Disabled go ppp4 pppoe_0_8_81 PPPoE N A N A Disabled Enabled Enabled Disabled Disabled Fj l eat ppps pppoe_0_0_33 PPPoE N A N A Disabled Enabled Enabled Disabled Disabled Fi ppp6 pppoe_0_0_40 PPPoE N A N A Disabled Enabled Enabled Disabled Disabled Fj Figure 12 Completing the settings of PPPoE WAN service 12 HN DR4PN2U User Manual 4 3 3 3G WAN Service Choose Advanced Setup gt 3G WAN Service and the following page appears modem status NO USB CARD Wide Area Network WAN Service For 3G Moblie Setup Choose Add Remove or Edit to configure a WAN service For 3G Moblie interface Interface Description Type Vian8021p VianMuxid Igmp NAT Firewall IPv6 Mid Remove Edit Action Add Upload
15. r heat dissipation Do not cover the device ventilation slots as this will result in the device overheating Do not install this device close to a heat source or in an area of high temperature Avoid exposure to direct sunlight Do not install in a damp environment or allow fluid to spill on the Modem or Power Supply Only connect this device as specified in the Manual or installation Wizard Failure to observe these instructions can lead to the risk of fire or damage to the equipment concerned Install in a well ventilated dry environment on a stable surface 2 Introduction The Router supports ADSL2 link with downstream up to 24 Mbps and upstream up to 1 Mbps It provides a simple and cost effective ADSL Internet connection for a private Ethernet The Router combines high speed ADSL Internet connection 3G WAN service IP routing for the LAN and wireless connectivity in one package The wireless network supports 802 11g 802 11b 802 11n It can provide high access performance application for the individual users SOHOs and small enterprises HN DR4PN2U User Manual 2 1 LED Status Description 2 1 1 Front Panel C G06 6 00 6 0 6 oO o Power ADSL Internet LAN4 LAN3 LAN2 LAN1 WLAN WPS USB 3 The following table describes the LEDs of the device LEDs Color Status Description The device is powered on and the device Green On operates normally Ono The device and is initiating The software is upgrading
16. ss of the Modem that means the communication of the PC and the Note Modem is normal ESCH WINNT system32 cmd exe C Copyright 1985 2000 Microsoft Corp C Documents and Settings Administrator gt arp a Interface 10 61 86 7 on Interface 0x1000003 Internet Address Physical Address Type 10 61 84 86 00 00 39 b5 67 2c dynamic 10 61 84 165 00 cO df b3 1c 04 dynamic 10 61 87 254 00 0a 8a 99 b2 00 dynamic Documents and Settings Administrator gt ping 192 168 1 1 Pinging 192 168 1 1 with 32 bytes of data 192 168 1 192 168 1 192 168 1 Reply from 192 168 1 1 bytes 32 time lt 10ms TTL 255 1 bytes 32 time lt 10ms TTL 255 1 bytes 32 time lt 10ms TTL 255 1 bytes 32 time lt 10ms TTL 255 Ping statistics for 192 168 1 1 Packets Sent 4 Received 4 Lost 0 0 loss Approximate round trip times in milli seconds Minimum Oms Maximum Oms Average Oms C Documents and Settings Administrator gt When you manage the router through Web do not cut off the power supply of the router Otherwise the router may be damaged 4 2 Logging In to the Router To log in to the DSL Router do as follows Step1 Step2 Step3 Step4 Open a Web browser on your computer Enter http 192 168 1 1 default IP address of DSL router in the address bar The login page appears Enter a user name and the password The default username and password of the super user are admin and password The username and password
17. the steps for adding the pppoe 0 0 40 PPPoE mode service Step1 In the Wide Area Network WAN Service Setup page click the Add button to display the following page At first you must add a proper ATM or ETH configuration for this WAN service WAN Service Interface Configuration Select a layer 2 interface for this service Note For ATM interface the descriptor string is portId_vpi_vci For PTM interface the descriptor string is portId_high_low Where portId 0 gt DSL Latency PATHO portid 1 gt DSL Latency PATH1 portid 4 gt DSL Latency PATHO amp 1 low 0 gt Low PTM Priority not set low 1 gt Low PTM Priority set high 0 gt High PTM Priority not set high 1 gt High PTM Priority set atmo 0 0 40 Figure 6 WAN service interface configuration PPPoE Step2 In this page you can select a ATM or ETH Interface for the WAN service After selecting the interface click Next to display the following page HN DR4PN2U User Manual WAN Service Configuration Select WAN service type PPP over Ethernet PPPoE FP over Ethernet Bridging Enter Service Description pppoe_0_0 40 C Enable IPv6 for this service Figure 7 WAN service configuration PPPoE Step3 In this page select the WAN service type to be PPP over Ethernet PPPoE Click Next to display the following page PPP Username and Password PPP usually requires that you have a user name and password to establish your connection In th
Download Pdf Manuals
Related Search
HN DR4PN2U