RX62N BOARD User Manual
Contents
1. be used by shifting jumpers on left side as shown below Similarly USB Device can be used by shifting jumpers to right side The details of connections are given below J gt USB Host USB Device JUMPER Selection for both USB Host and USB Device www coineltech com 9 I AN CoiNel Technology Solutions LLP 2 6 Test LED Buzzer Test Switch and Reset Switch Test LED Test Buzzer Test Switch and Reset Switch is provided onboard Test LED is connected at port PC1 Test Buzzer is connected at port P92 and Test Switch is connected at port P91 Keng 2 EEPROM Onboard 256kBit Serial Electrically Erasable PROM is provided EEPROM interfacing with Microcontroller via 12C lines 2 8 SERIAL FLASH Onboard 2MBYTE Serial Flash is provided Serial FLASH is interfacing with microcontroller via SPI lines 2 9 SDRAM Two No s of SDRAM is provided onboard The memory size of each SDRAM is 128MBIT SDRAM has 16 bit Data lines One SDRAM is used for microcontroller purpose and one more SDRAM is concern to EPSON driver 2 10 GPIO GPIO Pin outs are available onboard 16 pin box header is provided for GPIO pinouts There are two UART pin outs are available Namely UARTO and UARTE6 Pin No 1 rGPIO www coineltech com 10 I AN CoiNel Technology Solutions LLP 3 TFT Interfacing TFT Interfacing can be done through either 40 pin TFT connector or 20 pin LVDS connector The Supported TFT s2. an Lo hkhihkEkN Ki i Backlight connector for 40 pin TFT 10 4 inch TFT connector Test Buzzer Touch connector for 10 4 inch TFT www coineltech com I AN CoiNel Technology Solutions LLP 2 Peripheral Details 2 1 DC Power Input The Power supply to be used is only 5V DC 1Amp Onboard DC Jack is provided to connect 5V DC 1A Adaptor The Power LED will be ON once the board is powered up Connect DC Adaptor Plug here 5V only 2 2 JTAG Connector The 14 pin box header will be used to connect the JTAG for Debug Programming A 14 pin IO cable can be connected here which connects from emulator E Boot loader switch is provided on board The boot loader settings is shown below RENESAS d EI d l CS Boot selection 9 switch oo r E E VW E Cem be T Se Reeg e dE oy y e Ei Bape gt gailis suhi E Ss RP ELO terit s Fre ele P Ga 2 Jessa gt 14 Pin JTAG l Connector MCU Mode Settings Single Chip Mode Boot Mode USB Boot Mode Pin2 ON Pinl ON Do Not Set Pin2 ON www coineltech com 6 I AN CoiNel Technology Solutions LLP SWS3 Pin3 MDE Pin3 0 FF Big Endian Pin3 ON Little Endian SWS Pin4 P35 NMin USBO Power Select for USB Boot Mode FF Bus Powered erg Se lf Powered Emulator C onfiguration 1 2 bann E1 E20 ke with Hot ke iN 2 3 shorted r324 fitted E1 E20 nomal debugging ere ormicrocontroller single operation Note If Deb
3. any information herein and is not responsible for any errors or omissions CoiNel Technology Solutions LLP assumes no liability for damages resulting from use of such information in this document or for any infringement of intellectual property rights of third parties that would result from use of this information CoiNel Technology Solutions LLP assumes no liability for applications assistance Customer product design software performance or infringement of patents or services described herein For any enquires kindly contact info coineltech com www coineltech com 2 I AN CoiNel Technology Solutions LLP 1 0 2 0 3 0 TABLE OF CONTENTS Page INTFOCGUCTION 2 0 0 cc ccccceccccccccececccccceccaceceaceueaeaueneaceneaeeneneaceneaeeneaeeueneauentaeensuesueneaeenearsneetanentass 4 1 1 RX62N Board Features 4 1 2 RX62N Board Use Requirements n nnannnennennnnnnennnnenerennrnrrrnnrrrresrrnrrrsnrneresrrerrrerene 4 1 3 Functional Block Diagram of HaSpG2hN 5 tA Board A RTE HON EE 5 mod aces RE UE 6 2 1 DC Power INDUt cccccceeccceeeeceeeceeeeceeeceececeueeceeecsusesseeeseecsusesseessueesseeeseeesseeenaess 6 2 2 STAG CGonnechor n narran raaraa eaan EALLA AREA ananena nannan nenna 6 2 3 Micro GDCand nunen naeun naran a Laan A ALA a nnan aaraa n nanna nn ennn 8 2 4 Eibemmet nn rrrnanernn aneren 9 2 5 USB Connections ccccccccececcccccecececcccccacecececcacececeteceaeececeteceaeacecetensaeausc
4. are 3 5 4 3 5 7 7 and 10 4 inch TFT with touch 3 1 40 Pin TFT Connector 40 pin TFT connector is supported for all 3 5 4 3 and 7 inch TFT with touch External TFT board needs to be connect on this connector This 40 pin TFT connector is common for both Microcontroller and EPSON Driver At a time 40 pin TFT connector will run through Microcontroller or from EPSON Driver Resistor settings are provided to choose either Microcontroller or EPSON driver is shown in below figure 40 pin Connector s2 35 32 58 gf 8 EPSON DATA eu DATA Laa Pin TFT Connector 3 1 1 Microcontroller The supported TFT S are 3 5 4 3 5 7 7 inch TFT with Touch The Microcontroller supported resolution is 320X240 480X272 and 800X480 All TFT interfacing format is RGB 5 6 5 3 1 2 EPSON Driver 3 2 www We can interface only 7 inch TFI The EPSON Driver supported Resolution is 640X240 640X480 800X480 800X600 960X540 TFT interfacing format is RGB 8 8 8 20 Pin LVDS Connector 20 pin LVDS connector is supported for 10 4 inch TFT To drive 10 4 inch TFT We require EPSON driver The resolution of 10 4 inch TFT is 800X600 External Backlight Booster pin out is given onboard for 10 4 inch TFT TFT Touch connector 20 pin LVDS connector TFT Backlight Connector coineltech com 11 I AN CoiNel Technology Solutions LLP CLARIHCATIONS CoiNel is at your service and we have special Technical Support Engineers to pro
5. d CoiNel Technology Solutions LLP RX62N BOARD User Manual www coineltech com 1 AN CoiNel Technology Solutions LLP Designed by CoiNel Technology Solutions LLP No 32 Old No 1355 2nd Floor HAPBCO Tower 9th Main 4th B Cross Hampinagar RPC Layout Bangalore 560104 State Karnataka Country India www coineltech com Designations used by companies to distinguish their products are often claimed as trademarks In all instances where CoiNel is aware of trademark claim the product name appears in initial capital letters in all capital or in accordance with the vendor s capitalization preference Users should contact appropriate companies for more complete information on trademark and trademark registrations All trademarks and registered trademarks in this manual are the property of their respective holders No part of this document may be reproduced or distributed in any form or by any means or stored in the database or retrieval system without the prior written permission from CoiNel Technology Solutions LLP with the exception that the listings may be entered stored and executed in a computer system but they may not be reproduced The content in this document are presented for instruction value The details have been carefully tested but are not guaranteed for any particular purpose CoiNel Technology Solutions does not offer any warranties and does not guarantee the accuracy adequacy or completeness of
6. eneneneanens 9 2 6 Test LED Buzzer Test Switch and Reset Gwitch 10 2 mi ak ol a O es 10 2 8 Serial AS le cncentcccettesteeerciettcw se na cateete eectestnyetencasi vere cae tesco recess nctneantpeoeti deh eteasvemusinecentenaase atone datimaeteata 10 Ee RAI E 10 PAn LOCI nd O 10 TEE TST ACI E 11 3 1 40 Pin Connector E 11 3 1 1 Merocontfroller cece ccc cccccccccccecccccccccececceaccneeneaueceenesueceeneaneateneuneatententaneats 11 3 1 2 EPSON RU 11 3 2 20 Pin LVDS CGonnechor nn rnnnr nane 11 www coineltech com 3 I AN CoiNel Technology Solutions LLP 1 Introduction 1 1 RX62N Board Features MCU RX62N R5F562N8BDFB Onboard USB Host Connector USB type A Onboard USB device USB Mini Onboard Micro SD Card Interface ETHERNET Connectivity Option Onboard RESET Switch Onboard 14 pin JTAG connector for Debugging Programming Application Onboard Boot selection switch Onboard Power Reset and Test LED Onboard test switch and Buzzer UART TTL pin out x 2 GPIO pin outs Onboard RTC with 32 768 KHz crystal Onboard 12MHz crystal for main clock Onboard 256Kb EEPROM Onboard 16MBits Serial Flash Onboard SDRAM of 128MBits Onboard TFT driver chip along with SDRAM of 128Mbits optional Onboard LVDS transmitter for driving 10 4 TFT optional The TFT driver chip Supports resolutions up to 960x540 or 800x600 optional LCD direct drive via MCU Supports upto 800 x 480 resolution Onboard resist
7. or settings to choose TFT drive via TFT driver or MCU Direct LCD Supported TFT 3 5 4 3 5 7 7 and 10 4 Onboard Power supply Circuit for 3 3V and 2 5V Power Supply DC Input 5V 1A Board Specifications No of layers 4 Solder Mask Red Board Dimensions 110 x 60 mm Finish ENIG 1 2 RX62N Board use requirements e Operating System We recommend Windows XP since most of our testing is done on same platform although other OS can also be used e Integrated Development Environment We recommend HEW Other compatible IDE can be used e Debugging Programming Tool We recommend E1 EMULATOR Other compatible tools can be used e To test all the features of the board you would also require a USB Cable Ethernet cable straight a Micro SD Card DC power jack 5V 1Amp DC If you www coineltech com 4 I AN CoiNel Technology Solutions LLP also need to test the TFT you will need a 3 5 4 3 7 10 4 inch TFT Board provided by CoiNel 1 3 FUNCTIONAL BLOCK DIAGRAM OF RX62N BOARD 1 4 BOARD DESCRIPTION USB Host s USB Device d f wr ros 4 gt JTAG Connector ETHERNET lt E Boil EE EE 9 Boot loader Switch Jumper setting for both USB Host amp USB device d Tus DC Jack 5V Only 1 20 pin LVDS e WEE HTH OO OZ connector for 10 4 inch ES megt TY z TFT Es is feat gas 39393 gt Micro SD Card Test LED lt 27 F
8. ug flash program using E1 E20 Please be sure to set to Single Chip Mode SW3 1 OFF SW3 2 OFF 2 3 Micro SD card The correct way of inserting the SD card is given below The SD card is communicating to a controller via SPI Lines Pressing the card in the direction shown will lock the card once it will fully and properly inserted www coineltech com 7 AN CoiNel Technology Solutions LLP Note To remove the card press the card gently in the same direction shown above and then letting it loose The card will easily pop out and can be removed 2 4 Ethernet The correct way to plug the connector is given in the figure Press the connector in the direction shown and the connector will lock up properly when it is fully connected Ethernet will work only in RMII Mode ETHERNET Connector www coineltech com 8 I AN CoiNel Technology Solutions LLP Cable Connections 1 Orange Whee L 2 Orange 2 m 4 3 Green Vutite dr A 4 Bove ne 5 Biue Nnite 5 6 Green lt s 7 BrownWhite pee P Brown An Ethernet straight through cable is used for testing The recommended connection of the cable is also given 2 5 USB Connections The USB provided can either be used as a HOST or a Device The USB A Connector is used for the HOST interface while USB mini type for the device The jumper setting at J6 J7 J8 and J9 needs to be changed depending on whether the USB is used as a HOST ora Device Note USB Host can
9. vide support and consultation in forms of telephone and E mail TEL 91 80 23154423 Technical Support E mail support coineltech com For any questions or concerns submit them to info coineltech com www coineltech com 12
Download Pdf Manuals
Related Search