HWM8808 Wireless ADSL Router User Manual
Contents
1. Properties 4 Inthe TCP IP Properties dialog box click the IP Address tab Set the IP address as 192 168 1 x x can be a decimal number from 2 to 254 like 192 168 1 2 and the subnet mask as 255 255 255 0 5 On the Gateway tab set a new gateway as 192 168 1 1 and then click Add 6 Configure the DNS tab if necessary For information on the IP address of the DNS server please consult with user s ISP 7 Click OK twice to confirm and save user s changes 8 User will be prompted to restart Windows Click Yes Local PC Configuration in Windows 2000 1 Inthe Windows task bar click the Start button point to Settings and then click Control Panel 2 Double click the Network and Dial up Connections icon 3 Inthe Network and Dial up Connections window right click the Local Area Connection icon and then select Properties 4 Highlight Internet Protocol TCP IP and then click Properties 5 Inthe Internet Protocol TCP IP Properties dialog box set the IP address as 192 168 1 x x can be a decimal number from 2 to 254 and the subnet mask as 255 255 255 0 and the default gateway as 192 168 1 1 Then click OK 6 Configure the DNS tab if necessary For information on the IP address of the DNS server please consult with user s ISP 7 Click OK twice to confirm and save user s changes Wirel2. WLAN 5 The summary page presents the entire configuration summary Click Save if the settings are correct or Back to change any of the settings PORT VPI VCI 0 0 35 Connection Type Bridge Service Name br_0_0_35 Service Category UBR 1p Address Not Applicable Service State Enabled NAT Disabled Firewall Disabled IGMP Multicast Not Applicable Quality Of Service Disabled Note If you want to cancel all modification that you do on the Router please select from Management gt Setting gt Restore Default Settings to restore factory default settings 19 Wireless ADSL Router USER MANUAL 5 3 Wireless setting 5 3 1 Basic Enable Wireless C Hide Access Point E Clients Isolation Disable WMM Advertise SSID WLAN BSSID Country ALL CHANNELS v Max Clients 128 C Enable Wireless Guest Network Guest SSID Guest Enable Wireless Click this check box to enable the wireless network function Hide Access Point Checking this box can hide the SSID of this access point Then other people in the network cannot find the SSID of this device Clients Isolation Enable Clients Isolation if you don t want your wireless clients to communicate with each other SSID The system will detect the SSID of your router and displayed in this field for your reference The SSID is the identification characters of a router The default w
3. are connecting the device to more than one computer For system configuration using the supplied web based program A web browser such as Internet Explorer v5 0 or later or Netscape v4 7 or later Factory Defaults The device is configured with the following factory defaults IP Address 192 168 1 1 Subnet Mask 255 255 255 0 SSID WLAN Encapsulation RFC 2516 LLC VPI VCI According to local information Warnings and Cautions Never install telephone wiring during storm Avoid using a telephone during an electrical storm There might be a risk of electric shock from lightening Do not install telephone jacks in wet locations and never use the product near water To prevent dangerous overloading of the power circuit be careful about the designed maximum power load ratings Not to follow the rating guideline could result in a dangerous situation Please note that telephone line on modem must adopt the primary line that directly outputs from junction box Do not connect Router to extension phone In addition if your house developer divides a telephone line to multi sockets inside the wall of house please only use the telephone that has connected with the splitter of ADSL Router when you access the Internet Under the above condition if you also install telephone with anti cheat dial device please pull out this kind of telephone otherwise ADSL Router may occur frequently off line Wireless ADSL Router USER MANUAL
4. client s PSK does not match WPA2 PSK this option uses WPA2 with a pre shared key WPA2 and WPA This option supports an authentication server and WPA2 WPA encryption for devices capable of one or the other standard The gateway automatically detects whether a particular device can use WPA2 or WPA WPA2 AND WPA PSK this has WPA2 or WPA encryption based on client abilities as well as a pre shared key After making changes click Apply to save 22 Wireless ADSL Router USER MANUAL Appendix Frequent Asked Questions Q A Q None of the LEDs are on when user power on the ADSL router Please make sure what user use is the power adaptor attached with the ADSL router package and check the connection between the AC power and ADSL router DSL LED does not turn on after connect telephone line Please make sure what user use is the standard telephone line as attached with the package make sure the line is connected correctly and check whether there is poor contact at each interface Wait for 30 seconds to allow the ADSL router establishes connection with user ADSL operator DSL LED is in the circulation of slow flashing and fast flashing after connect telephone line A This situation means the ADSL router is in the status of failing to establish connection with Central Office Please check carefully and confirm whether the ADSL router has been installed correctly LAN LED does not turn on after con
5. g your computer Do not disable the DHCP server unless you wish to let another device handle IP address issuance on the local network This is the beginning and ending range for the DHCP server addresses The amount of time before the IP address is refreshed by the DHCP server Use this feature to create a public network on your local LAN accessible from the Internet By assigning an address to this interface and then statically setting your LAN clients to the same network the LAN clients are accessible from the public network e g FTP or HTTP 13 Wireless ADSL Router USER MANUAL servers 5 Set SSID for wireless network if user enabled the wireless function Enable Wireless Enter the wireless network name also known as SSID ssp WLAN 6 Make sure that the settings below match the settings provided by your ISP PORT VPI VCI 0 0 35 Connection Type PPPoE Service Name pppoe_0_0_35_1 Service Category UBR IP Address Automatically Assigned Service State Enabled NAT Enabled Firewall Enabled IGMP Multicast Disabled Quality Of Service Disabled 7 Click on the Save Reboot button to save your configurations b PPP over ATM PPPoA 1 Select PPP over ATM PPPoA as connection type and select VC MUX as encapsulation mode PPP over ATM PPPoA PPP over Ethernet PPPoE MAC Encapsulation Routing MER IP over ATM IPoA Bridg
6. then connect the wall phone jack to the LINE port of the splitter The splitter comes with three connectors as below LINE Connects to a wall phone jack RJ 11 jack ROUTER Connects to the DSL jack of ROUTER PHONE Connects to a telephone set 2 Using an Ethernet Cable to connect the LAN port of the ROUTER to user s LAN or a PC with network card installed Or using an USB cables to connect the USB port of the ROUTER to user s PC OSS S7 ose MAS we A ON OFF POWER ETH1 ETH2 EHT3 ETH4 To WLAN receivers RJ11 Wall outlet witl ADSL Service 3 Connect the power cable to the POWER connector on ROUTER then plug in the AC power adapter to the power outlet and then press the on off button Notes Without the splitter and certain situation transient noise from telephone can interfere with the operation of the Router and the Router may introduce noise to the telephone line To prevent this from happening a small external splitter must be connected to each telephone Wireless ADSL Router USER MANUAL 4 PC Configuration Guide 4 1 4 2 Local PC Configuration in Windows 95 98 ME XP 1 Inthe Windows task bar click the Start button point to Settings and then click Control Panel 2 Double click the Network icon 3 On the Configuration tab select the TCP IP network associated with user s network card and then click
7. to legal IP address IP address range of the PC that user specify should meet the setting range in NAT rules 4 Central Office equipment may have problem 5 The country or the wireless network type user selected is wrong PC cannot browse Internet web page 23 Wireless ADSL Router USER MANUAL A Please make sure DNS server appointed to the PC is correct User can use ping application program to test whether the PC can connect to the DNS server of the ADSL operator Q Initialization of the PVC connection failed A Be sure that cable is connected properly from the DSL port to the wall jack The DSL LED on the front panel of the ADSL router should be on Check that user s VPI VCI type of encapsulation and type of multiplexing setting are the same as what user collected from user s service provider Re configure ADSL router and reboot it If user still can not work it out user may need to verify these variables with the service provider If the cause is not above given please contact user s local service provider 24
8. 2 Hardware Description Front Panel rs amp ETH2 ETH3 ETH4 WLAN DSL Function On Power Off No power On LAN link established and active via LAN port Blinking ADSL data activity occurs Off No LAN link via LAN port On The wireless module is ready and idle Blinking Data transmitting or receiving over WLAN Off The wireless function is off On ADSL link established and active Quick blinking ADSL is trying to establish a connection Slow blinking no ADSL link Blinking ADSL data activity occurs Off No ADSL data is being sent or received Wireless ADSL Router USER MANUAL ANT ON OFF POWER Rear panel Function Connect the device to an ADSL telephone jack or splitter using a RJ 11 telephone cable System reset or reset to factory defaults Connect the device to user s PC s Ethernet port or to the uplink port on user s hub switch using a RJ 45 cable POWER Connect to the supplied power adapter ON OFF Switch it on or off ANT Antenna interface Wireless ADSL Router USER MANUAL 3 Hardware Installation This chapter shows user how to connect Router Meanwhile it introduces the appropriate environment for the Router and installation instructions 1 Using a telephone line to connect the DSL port of ROUTER to the Modem port of the splitter and using a other telephone line connect user s telephone to the PHONE port of the splitter
9. 8 1 254 Subnet Mask 255 255 255 0 Leased Time hour 24 Configure the second IP Address and Subnet Mask for LAN interface IP Address 10 0 0 1 Subnet Mask 255 0 0 0 16 Wireless ADSL Router Item IP address Subnet mask Disable Enable DHCP server Start end IP address Lease time Configure the second IP address and USER MANUAL Description This is the IP address that other devices on your local network will use to connect to the modem This defines the size of your network The default is 255 255 255 0 The DHCP server assigns an IP addresses from a pre set pool of addresses upon request from DHCP client e g your computer Do not disable the DHCP server unless you wish to let another device handle IP address issuance on the local network This is the beginning and ending range for the DHCP server addresses The amount of time before the IP address is refreshed by the DHCP server Use this feature to create a public network on your local LAN accessible from the Internet By assigning an address to this interface and then statically setting your LAN clients to the same network the LAN clients are accessible from the public network e g FTP or HTTP servers 5 Set SSID for wireless network if user enabled the wireless function Enable Wireless Enter the wireless network name also known as SSID SSID WLAN 6 M
10. HWM8808 Wireless ADSL Router User Manual HANTOL Wireless ADSL Router USER MANUAL NOTICE This document contains proprietary information protected by copyright and this Manual and all the accompanying hardware software and documentation are copyrighted All rights are reserved No part of this document may be photocopied or reproduced by mechanical electronic or other means in any form The manufacturer does not warrant that the hardware will work properly in all environments and applications and makes no warranty or representation either expressed or implied with respect to the quality performance merchantability or fitness for a particular purpose of the software or documentation The manufacturer reserves the right to make changes to the hardware software and documentation without obligation to notify any person or organization of the revision or change All brand and product names are the trademarks of their respective owners Copyright 2009 All rights reserved 1 OVERVIEW 1 1 FEATURES 1 2 PACKET CONTENTS 1 3 SYSTEM REQUIREMENTS 1 4 Factory DEFAULTS 1 5 WARNINGS AND CAUTIONS 2 HARDWARE DESCRIPTION 3 HARDWARE INSTALLATION 4 PCCONFIGURATION GUIDE 4 1 LOCAL PC CONFIGURATION IN WINDOWS 95 98 ME XP 4 2 LOCAL PC CONFIGURATION IN WINDOWS 2000 5 WEB BASED MANAGEMENT GUIDE 5 1 LAN SETTING PAGE 5 2 INTERNET ACCESS CONFIGURATION QUICK SETUP 5 3 WIRELESS SETTING APPENDIX Content FREQUENT A
11. SKED QUESTIONS Wireless ADSL Router 1 Overview USER MANUAL Thank you for choosing our product The HW WD308 Wireless ADSL Router uses Broadcom s CPE solution that fully complies with ADSL ADSL2 ADSL2 and IEEE802 11b g standards It will provide your SOHO with convenient Internet access 1 1 Features 1 4 1 Data Rate e Downstream data rate up to 24 Mbps Upstream data rate up to 1Mbps 1 1 2 ADSL Compliance 1 1 3 Wireless ITU G 992 1 G DMT ITU G 992 2 G Lite ITU G 994 1 G hs ITU G 992 3 G DMT BIS ITU G 992 4 G lite bis ITU G 992 5 Compatible with all T1 413 issue 2 full rate DMT over analog POTS and CO DSLAM equipment TR 069 compliant with ACS Fully IEEE 802 11b amp IEEE 802 11g compatible Wireless data rate up to 54 Mbps Operating in the unlicensed 2 4 GHz ISM band Multiple SSID Supports 64 128 bits WEP security and user authentication 1 1 4 Network Protocol amp Features Ethernet to ADSL Self Learning Transparent Bridging Internet Control Message Protocol ICMP 1 Wireless ADSL Router 1 1 5 1 1 6 USER MANUAL IP Static Routing Routing Information Protocol RIP RIPv2 Network Address Translation NAT Virtual Server Port Forwarding Dynamic Host Configuration Protocol DHCP DNS Relay DDNS IGMIP Proxy Simple Network Time Protocol SNTP VPN pass through IPSec PPTP L2TP Parent control ATM Capabilities FIREWALL RFC 1483 Multi protocol over A
12. TM Bridged Ethernet compliant RFC 2364 PPP over ATM compliant RFC 2516 PPP over Ethernet compliant ATM Forum UNI3 1 4 0 PVC Up to 8 PVCs VPI Range 0 255 VCI Range 32 65535 UNI 3 0 amp 3 1 Signaling ATM AALS Adaption Layer type 5 OAM F4 F5 Built in NAT MAC Filtering Packet Filtering Stateful Packet Inspection SPI Denial of Service Prevention DoS Wireless ADSL Router USER MANUAL 1 1 7 12 13 e DMZ Management Support Web Based GUI e Upgrade or update via FTP HTTP e Command Line Interface via Telnet Diagnostic Test Firmware upgradeable for future feature enhancement Operating System Support WINDOWS 98 SE ME 2000 XP VISTA Macintosh LINUX Environmental Operating humidity 10 90 non condensing Non operating storage humidity 5 95 non condensing Packet Contents The packet contents are as the following ADSL ROUTER x1 External Splitter x1 Power Adapter x1 Telephone Line x1 Ethernet Cable x1 System Requirements Before using this ROUTER verify that you meet the following requirements Subscription for ADSL service Your ADSL service provider should provide you with at least one valid IP address static assignment or dynamic assignment via dial up connection Wireless ADSL Router USER MANUAL 1 4 1 5 One or more computers each contains an Ethernet 10 100M Base T network interface card NIC A hub or switch if you
13. ake sure that the settings below match the settings provided by your ISP 17 Wireless ADSL Router USER MANUAL PORT VPI VCI 0 0 35 Connection Type PPPoA Service Name pppoa_0_0 35 1 Service Category UBR IP Address Automatically Assigned Service State Enabled NAT Enabled Firewall Enabled IGMP Multicast _ Disabled Quality Of Service Disabled _ 7 Click on the Save Reboot button to save your configurations c Bridging RFC 2684 Select the bridge operating mode if your ADSL service provider tells you that you should To configure bridging do the following 1 Select Bridging RFC 2684 as connection type PPP over ATM PPPoA PPP over Ethernet PPPoE MAC Encapsulation Routing MER IP over ATM IPoA Bridging Encapsulation Mode LLC SNAP BRIDGING v 2 Select the appropriate Encapsulation mode and click Next The following screen appears Enable Bridge Service Service Name br_0_0_35 3 Enable or disable bridge service and enter a bridge service name Click Next and configure the DSL Router IP Address and Subnet Mask for your Local Area Network LAN 18 Wireless ADSL Router USER MANUAL IP Address 192 168 1 1 Subnet Mask 255 255 255 0 4 Set SSID for wireless network if user enabled the wireless function Enable Wireless Enter the wireless network name also known as SSID SSID
14. emote service provider to the LAN computer That is the PC becomes a host belonging to the same IP subnet The ADSL gateway bridges the IP packets between WAN and LAN ports unless the packet is addressed to the gateway s LAN IP address 3 Unselect Enable IGMP Multicast and select Enable WAN Service and then click Next Enable IGMP Multicast Enable WAN Service Service Name pppoe_0_0 35_1 4 Configure the DSL Router s IP Address and Subnet Mask for LAN interface In this page you can use DHCP Dynamic Host Configuration Protocol to control the assignment of IP addresses on your local network LAN only 12 Wireless ADSL Router USER MANUAL Disable DHCP Server Enable DHCP Server Start IP Address End IP Address Subnet Mask 192 168 1 2 192 168 1 254 255 255 255 0 Leased Time hour 24 Configure the second IP Address and Subnet Mask for LAN interface IP Address 10 0 0 1 Subnet Mask 255 0 0 0 Item Description This is the IP address that other devices on your local network will use IP address Subnet mask Disable Enable DHCP server Start end IP address Lease time Configure the second IP address and to connect to the modem This defines the size of your network The default is 255 255 255 0 The DHCP server assigns an IP addresses from a pre set pool of addresses upon request from DHCP client e
15. ess ADSL Router USER MANUAL 5 Web based Management Guide In order to use the web based management software it will be necessary to use a computer that occupies the same subnet as the Router The simplest way to do this for many users will be to use DHCP server that is enabled by default on the Router 5 1 LAN setting page Launch a web browser such as Internet Explorer and then use hitp 192 168 1 1 to log on tothe setting page Connect to 192 168 1 1 Enter username admin and password admin Click OK After user log in to the modem the general status page appears 5 2 Internet Access Configuration The setup wizard will guide you to configure the DSL router to access Internet Quick Setup If there aren t any pre configured PVCs in the router you ca find Quick Setup option on the left of router configuration page Or user can delete the PVCs preconfigured to find the option 1 From home page clickQuick Setup ATM PVC Configuration Select the check box below to enable DSL Auto connect process DSL Auto connect Wireless ADSL Router USER MANUAL 2 Unselect the check box to disable DSL Auto connect process Set VPI VCI value provided by your ISP The Port Identifier PORT Virtual Path Identifier PI and Virtual Channel Identifier VCI are needed For setting up the ATM PVC Do not change YPI and YCI numbers unless your ISP instructs you otherwise PORT 0 3 0 WPI 0 255
16. ing Encapsulation Mode YC MUX v e 14 Wireless ADSL Router USER MANUAL 2 Input PPP Username amp PPP Password and then click Next The user interface allows a maximum of 256 characters in the user name and a maximum of 32 characters in the password Just remember to enable NAT and Firewall as below PPP Username username L PPP Password esssesoe Authentication Method AUTO v O Enable Fullcone NAT NAT Firewall O Dial on demand with idle timeout timer EC PPP IP extension Use Static IP Address o E Retry PPP password on authentication error C Enable PPP Debug Mode Authentication method is default to Autoc It is recommended that you leave the Authentication method in Auto however you may select PAP or CHAP if necessary The default value for MTU Maximum Transmission Unit is 1500 for PPPoA and 1492 for PPPoE Do not change these values unless your ISP asks you to The gateway can be configured to disconnect if there is no activity for a specific period of time by selecting the Dial on demand check box and entering the Inactivity timeout The entered value must be between 1 minute to 4320 minutes The PPP IP Extension is a special feature deployed by some service providers Unless your service provider specifically requires this setup do not select it If you need to select it the PPP IP Extension supports the following conditions It allows only one computer on
17. nect Ethernet cable Please make sure Ethernet cable is connected hub PC and ADSL router correctly Then please make sure the PC hub have been power on Please make sure that user use parallel network cable to connect UpLink port of hub or use parallel network cable to connect PC If connect normal port of hub not UpLink port user must use cross cable Please make sure that user s network cables meet the networking requirements above PC cannot access the Router Please make sure that all devices communicating with the device must use the same channel and use the same SSID Otherwise user s PC will not find the wireless Router PC cannot access the Internet First check whether PC can ping the interface Ethernet IP address of this product successfully default value is 192 168 1 1 by using ping application If ping application fails please check the connection of Ethernet cable and check whether the states of LEDs are in gear If the PC uses private IP address that is set manually non registered legal IP address please check 1 Whether IP address of the PC gateway is legal IP address Otherwise please use the right gateway or set the PC to Obtain an IP address automatically 2 Please confirm the validity of DNS server appointed to the PC with ADSL operator Otherwise please use the right DNS or set the PC to Obtain an IP address automatically 3 Please make sure user have set the NAT rules and convert private IP address
18. o yCI 32 65535 35 Enable Quality Of Service Enabling QoS for a PYC improves performance for selected classes of applications However since QoS also consume PYCs will be reduced consequently Use Advanced Setup Quality of Service to assign priorities for the applications ystem resources the number of Enable Quality Of Service C a PPP over Ethernet PPPoE 1 Select PPP over Ethernet PPPoE as connection type and select LLC SNAP BRIDGING as encapsulation mode PPP over ATM PPPoA PPP over Ethernet PPPoE MAC Encapsulation Routing MER IP over ATM IPoA Bridging Encapsulation Mode LLC SNAP BRIDGING wv 2 Input PPP Username amp PPP Password and then click Next The user interface allows a maximum of 256 characters in the user name and a maximum of 32 characters in the password Just remember to enable NAT and Firewall as below 10 Wireless ADSL Router USER MANUAL PPP Username username PPP Password eecccecce PPPoE Service Name Authentication Method AUTO vi E Enable Fullcone NAT NAT Firewall E Dial on demand with idle timeout timer C PPP IP extension O Use Static IP Address E Retry PPP password on authentication error C Enable PPP Debug Mode Bridge PPPoE Frames Between WAN and Local Ports Default Enabled PPPoE service name can be blank unless your Internet Service Provider gives you a value to ente
19. ords will be shown on this page If you do not check the Hide Access Point item the router will periodically broadcasts its SSID to allow the wireless clients within the range to recognize its presence This can create a security hole since any wireless clients which got the broadcast might associate to your system Please be noted that if you want to communicate all wireless clients should use the same SSID with the router or access point Country Select the country your Router work in Different country use different channel 5 3 2 Security To configure security features for the Wireless interface please open Security item from Wireless menu This web page offers nine authentication protocols for user to secure user s 20 Wireless AD SL Router USER MANUAL data while connecting to networks There are four selections including Open Shared 802 1X WPA WPA PSK WPA2 WPA2 PSK Mixed WPA WPA2 Mixed WPA WPA2 PSK Different item leads different web page settings Please read the following information carefully The wireless security page allows user to configure the security features of user s wireless network Select SSID WLAN oy Network Authentication Shared v WEP Encryption Enabled v Encryption Strength 128 bit v Ba Current Network Key ly Network Key 1 Network Key 2 Network Key 3 Network Key 4 Enter 13 ASCII characters or 26 hexadecimal digits for 128 bit encryption key
20. r Authentication method is default to Auto It is recommended that you leave the Authentication method in Auto however you may select PAP or CHAP if necessary The default value for MTU Maximum Transmission Unit is 1500 for PPPoA and 1492 for PPPoE Do not change these values unless your ISP asks you to The gateway can be configured to disconnect if there is no activity for a specific period of time by selecting the Dial on demand check box and entering the Inactivity timeout The entered value must be between 1 minute to 4320 minutes The PPP IP Extension is a special feature deployed by some service providers Unless your service provider specifically requires this setup do not select it If you need to select it the PPP IP Extension supports the following conditions It allows only one computer on the LAN The public IP address assigned by the remote using the PPP IPCP protocol is actually not used on the WAN PPP interface Instead it is forwarded to 11 Wireless ADSL Router USER MANUAL the computer s LAN interface through DHCP Only one system on the LAN can be connected to the remote since the DHCP server within the ADSL gateway has only a single IP address to assign to a LAN device NAPT and firewall are disabled when this option is selected The gateway becomes the default gateway and DNS server to the computer through DHCP using the LAN interface IP address The gateway extends the IP subnet at the r
21. s Enter 5 ASCII characters or 10 hexadecimal digits for 64 bit encryption keys There are several security methods to choose from depending on user s needs and the capabilities of user s wireless machines Open Shared 802 1X WPA WPA PSK WPA2 WPA2 PSK Mixed WPA2 WPA Mixed WPA2 WPA PSK WEP open and WEP shared WEP is an encryption scheme that is used to protect user s wireless data communications WEP uses a combination of 64 bit keys or 128 bit keys to provide access control to user s network and encryption security for every data transmission To decode a data transmission each wireless client on the network must use an identical 64 bit or 128 bit key WEP is an older wireless encryption method that is not as hard to break as the more recent WPA 802 1x In 802 1x also known as RADIUS a separate machine called an authentication server receives a user ID and password It grants or denies access based on whether the ID and password match any entries in its account list User can optionally enable WEP encryption with this option Because it requires a separate machine acting as the authentication server 802 1x is most often used in business environments 21 Wireless ADSL Router USER MANUAL WPA PSK This is WPA encryption combined with a pre shared key PSK which is a text string known only to the gateway and authorised wireless clients The gateway rejects the login if the
22. the LAN The public IP address assigned by the remote using the PPP IPCP protocol is actually not used on the WAN PPP interface Instead it is forwarded to the computer s LAN interface through DHCP Only one system on the 15 Wireless ADSL Router USER MANUAL LAN can be connected to the remote since the DHCP server within the ADSL gateway has only a single IP address to assign to a LAN device NAPT and firewall are disabled when this option is selected The gateway becomes the default gateway and DNS server to the computer through DHCP using the LAN interface IP address The gateway extends the IP subnet at the remote service provider to the LAN computer That is the PC becomes a host belonging to the same IP subnet The ADSL gateway bridges the IP packets between WAN and LAN ports unless the packet is addressed to the gateway s LAN IP address 3 Unselect Enable IGMP Multicast and select Enable WAN Service and then click Next Enable IGMP Multicast Enable WAN Service Service Name pppoa_0_0_35_1 4 Configure the DSL Router s IP Address and Subnet Mask for LAN interface In this page you can use DHCP Dynamic Host Configuration Protocol to control the assignment of IP addresses on your local network LAN only IP Address 192 168 1 1 Subnet Mask 255 255 255 0 Disable DHCP Server Enable DHCP Server Start IP Address 192 168 1 2 End IP Address 192 16
Download Pdf Manuals
Related Search