DAG Series FXO Voice Gateway User Manual V2.0
Contents
1. DINSTAR DAG Series FXO Voice Gateway User Manual V2 0 Dinstar Technologies Co Ltd Address Floor 6 Guoxing Building Changxing Road Nanshan District Shenzhen China 518052 Telephone 86 755 26456664 Fax 86 755 26456659 Email sales dinstar com support dinstar com Website www dinstar com Revision Records File Name DAG Series FXO Voice Gateway User Manual Document Version Revised by Technical Support Department Table of Contents EQUIPMENT INUFOCUGCT lei 1 PEON OW OV e 1 1 2 Equipment appearance cccesssccsccrsssssconscerseussousserssssscesscrssssussonseerseens 1 Lo POWwer EEN 2 T4INCTWOFK ADDIIGATI ONS EE 2 1 5 Functions and e Zelt EEN 3 1 5 1Protocol standard SUPPoOrted ccc cee ccssccessscsesseeessseeessseeeseeens 3 1 5 2 Voice and Fax ParaMeter ccccessscscesssseccesssecessesecsssesevsseeseres 3 1 5 3 Supplementary service ccccccccessscscesssesecessesecessesecesseseveseesees 3 Basic SAU ONNS E 4 Zod PRONE e EE 4 2 1 1 Phone or Extension Number 4 2 V2 Dre IR UE 4 E TEE 5 2 3 Sending and RECEIVING MCK EE 6 2 3 1 DAG FXS support four fax modes eeren 6 2 3 2 T38 ANG PASS NTOUGN E 7 LOCA IVR ODE AON E 7 Se Me aa UE 8 6 oc one eee nee ent ee eRe Cee rear A 7 32 Fa tO EE 7 3 3 Configure LAN Porte IP Address 7 EENEG ran E deter sata N ANS 8 EWED g BEE 8 E LOG EE 8 e OC OG Mt WEB EE 9 42 Navigation JEE 10 Foe ANa eege 11 Ek System AOMaAa O i2. 1 Click ping test 50 Dinstar Technologies Co Ltd DINSTAR DAG Series FXO Voice Gateway User Manual 2 Fill IP address or domain connected click start 3 Received a message indicates that network connection normal or network connected to a fault Ping Test Destination Number of Ping 1 100 Packet Size 56 1024 bytes Information Figure 4 11 5 Ping Parameter Interface 4 11 6 Tracert Test Tracert is trace router and used to tracking routing Tracert sends a sequence of Internet Control Message Protocol ICMP echo request packets addressed to a destination host Determining the intermediate routers traversed involves adjusting the time to live TTL aka hop limit Internet Protocol parameter Frequently starting with a value like 128 Windows or 64 Linux routers decrement this and discard a packet when the TTL value has reached zero returning the ICMP error message ICMP Time Exceeded Tracert works by increasing the TTL value of each successive set of packets sent The first set of packets sent have a hop limit value of 1 expecting that they are not forwarded by the first router The next set have a hop limit value of 2 so that the second router will send the error reply This continues until the destination host receives the packets and returns an ICMP Echo Reply message Trace route uses the returned ICMP messages to produce a list of hops which usually consists 51 Dinstar Technologies Co
3. DINS TAR DAG Series FXO Voice Gateway User Manual It is use to control the volume of conversation Adjust TX gain will affect Tx Gain the end users voice size the default value is 0 Its value range from 10 10 dB It is use to control the volume of conversation Adjust RX gain will affect Rx Gain the end users voice size the default value is 0 Its value range from 10 10 dB Primary Secondary SIP Primary Secondary SIP account description Its purpose is so you can Display Name identify the SIP account with a meaningful name Primary Secondary User account information provided by VoIP service provider ITSP Usually SIPUser ID in the form of digit similar to phone number or actually a phone number Primary Secondary SIP SIP service subscriber s Authenticate ID used for authentication Can be Authenticate ID identical to or different from SIP User ID Primary Secondary l l l l SIP password which registers to soft switch SIP server Authenticate password l Pre assign an extension or phone number so that automatically dial a Offhook Auto dial l number as soon as you pick up the phone set Delay 0 3 seconds to automatically dial a number 0 means dial number Auto dial Delay Time immediately 4 8 Advanced 4 8 1 FXS FXO FXO is Foreign Exchange Office It is a kind of voice interface and a trunk connected between central exchange switches and telephone exchange system To central office speaking it simula
4. 3 Click Upload the upload process will last about 60s and device can automatically restart after uploading The firmware update process don t shut off the power Firmware Upload Send ld file from your computer to the device Sofware EE FAETH Notes 1 The upload process willlast about 60s 2 The device will restat automatically after upload 3 Do not shut down when the device is uploading Figure 4 11 2 Firmware upload Configuration 49 Dinstar Technologies Co Ltd DINSTAR DAG Series FXO Voice Gateway User Manual 4 11 3 Data Backup The process data backup 1 Click Data Backup 2 Click Backup to backup data to PC Data Backup Click Backup for download configuration file to your computer Figure 4 11 3 Data Backup Interface 4 11 4 Data Restore The processes of data restore 1 Click Data Restore 2 Browse file select data file 3 Click Restore and then import successfully the device will restart automatically Data Restore send data file from your computer to the device Configuration Figure 4 11 4 Data Restore Interface 4 11 5 Ping Test Send test data packets to IP check each other whether have response and statistical response time It is ping Used to test internet and analyzed network fault Application format Ping IP address It is used to check the network connectivity or network connection speed command Pinginstructions
5. DAG1000 4S VolP access atewa S i amp E d e Phone Phone Phone Phone Phone Phone Phone Phone Figure 4 1 Network Applications Dinstar Technologies Co Ltd DINSTAR DAG Series FXO Voice Gateway User Manual 1 5 Functions and Features 1 5 1Protocol standard supported e SIP V2 0 RFC 3261 3262 3264 SDP RFC 2327 e REFER RFC 3515 RTP RTCP RFC 1889 1890 STUN RFC 3489 e ARP RARP RFC 826 903 SNTP RFC 2030 e DHCP PPPoE TFTP HTTP HTTPS DNS DNS SRV RFC 1706 RFC 2782 e VLAN 802 1P 802 1Q Diff Server 1 5 2 Voice and Fax parameters e G 711A U law G 723 1 G 729AB e Comfortable Noise Generation CNG e Voice Activity Detection VAD e Echo Cancellation G 168 Adaptive Dynamic Jitter Buffer e Voice and fax gain control Modem T 38 Pass through DTMF Mode Signal RFC2833 INBAND 1 5 3 Supplementary service Busy tone detection No current take out stitches detection e Voice interrupted detection e One stage dialing e Two stage dialing PSTN exterior ports polling e Polarity Reversal e FAS Fake billing correction DC AC impedance config e Calls detection Bellcore Type 1 amp 2 ETSI DTMF Dinstar Technologies Co Ltd DINS TAR DAG Series FXO Voice Gateway User Manual e Voice mail e Direct IP Call e JP Trunk 2 Basic Operations 2 1 Phone Call 2 1 1 Phone or Extension Number 1 FXO Call Out e
6. Ltd DINS TAR DAG Series FXO Voice Gateway User Manual 4 8 5 Digit Map Digit Map NOTE Length of Digit Map should not be more than 119 characters Figure 4 8 9Digit Map Gateway is collect digits dialed by user if received a number to be immediately report the efficiency is too low and a large number of take up network resources A reasonable method is concentration sending a message after receiving all number How to judge the gateway receiving all number is the difficulties of this method The solution is the call agent loading a Digit Map to gateway Digit Map includes a series figure characters when the dial up sequence and one received a character string matching it means the number has received neat Digital string contains characters allowed data0 9 letterA D letter T letter x and parts of each WK string is a choice of dial up solutions means choose anyone means one reports letter T means detected timer overtime x means any data means multiple characters can be behind include 0 means report immediately Digit Map Syntax 1 Supported objects Digit A digit from 0 to 9 Timer The symbol T matching a timer expiry DTMF A digit a timer or one of the symbols A B C D or 35 Dinstar Technologies Co Ltd DINS TAR DAG Series FXO Voice Gateway User Manual 2 Range One or more DTMF symbols enclosed betwee
7. T T2 16 22 222 793 299 0 0 f2 16 1 1 00 Auto Detect 9 7 163 11 1 Ab ZA 755 0 00 02 96 123 66 ho ho ho pc A i 02 96 134 133 Notes The following settings are available on route mode only 4 5 2 VLAN Parameter Generally Internet provides only Best Effort Service Since ethernet is the most spread LAN access technology importance of providing it a quality of service mechanism ought not to Dinstar Technologies Co Ltd 15 DINS TAR DAG Series FXO Voice Gateway User Manual be neglected Ethernet technology also used as WAN technology not only as LAN technology Due to rapidly increasing use Internet through Public Switched Telecommunication Network PSTN Telephone Companies are forced to implement IP based networks as their PSTN backbones A network like this without any Quality of Service mechanisms would be disastrous Just imagine yourself trying to get an emergency call through while others just surf the Internet 1 802 1Q The IEEE 802 1Q standard defines architecture for Virtual Bridged LANs the services provided in Virtual Bridged LANs and the protocols and algorithms involved in the provision of those services No Quality of Service mechanisms are defined in this standard but an important requirement for providing QoS is included in this standard e g abitity to regenerate user priority of received frames using priority information contained in the frame and the User Priority
8. 802 1Q VLAN ID 0 4095 used to management VLAN can t used to service Data VLAN configure a 802 1 protocol to control network traffic priority Data 802 1p Priority 0 7 o Priority from 0 7 l Fill out an ID to describe a voice VLAN group ID 0 Voice 802 1Q VLAN ID 0 used to management VLAN can t used to service 4095 configure l l o 802 1 protocol to control network traffic priority Voice VALN Voice 802 1p Priority 0 7 Priority from 0 7 IP address Can use dynamic or static IP address Voice VLAN DNS Server Can use dynamic or static DNS server address Fill out an ID to describe a data VLAN group ID 0 used to management VLAN can t used to service Management 802 1Q VLAN ID 0 4095 Management configure VLAN Management 802 1p Priority 802 1 protocol to control network traffic priority 0 7 Priority from 0 7 IP address Can use dynamic or static IP address 17 Dinstar Technologies Co Ltd DINS TAR DAG Series FXO Voice Gateway User Manual Management VLAN DNS Can use dynamic or static DNS server address server Note restart the device to take configuration effect 4 5 3 MAC Clone Routing mode MAC Clone This page provides the setting MAC address of WAN PC MAC Address BC AE C5 4A 79 E9 Device MAC Address 00 1F D6 97 02 7D Note The device mustrestartto take effect Figure 4 5 4 MAC Clone Interface More client in LAN have already can t share internet used the trad
9. Digit Map eature Code system Parameter Call amp Routing Manipulation Maintenance 10 Dinstar Technologies Co Ltd DINS TAR DAG Series FXO Voice Gateway User Manual Figure 4 2 1 Navigation Tree When device is in bridge mode navigation tree won t display routing configuration items and the following DHCP service DMZ host forward rules and static routing and ARP etc 4 3 State and Statistics 4 3 1 System Information System information interface shows the run information as following figure 4 3 1 below System Information MAC Address 00 12 34 56 7 8 00 Network Mode Bridge IP Address 172 16 22 222 255 255 0 0 Static 172 186 1 1 DNS Server 202 956 128 658 202 956 134 133 System Uptime Oh 01m 36s NTP Status Succeed Network Traffic Stat Received 1711574 bytes sent 30170 bytes Version DAG1000 80 Rev 2 11 08 05 PCB 23 1 LOGIC 0 BIOS 1 Built on Nov 30 2013 15 12 09 Hint Language English Figure 4 3 1 System Information System information as follow Table 4 3 1 System Information Description MAC address WAN port hardware address The device ID in HEX format Display network mode include bridge and rout If it is bridge WAN port display Network Mode Network and the WAN port IP as same as the LAN port IP Shows WAN IP address of DAG DHCP mode all the field values for the Static IP mode are not used eventhough they are still saved in the Flash memory The DAG acquires its IP a
10. Ltd DINSTAR DAG Series FXO Voice Gateway User Manual of routers and layer 3 switches that the packets have traversed The timestamp values returned for each router along the path are the delay aka latency values typically measured in milliseconds for each packet Tracert introduce 1 Click tracert test 2 Fill IP address or domain connected click start Tracert Test Destination Max Hops 1 255 Information Figure 4 11 6 Tracert Test Interface 4 11 7 Password Modification Includes WEB username and password Telenet username and password modify Note Default web and telnet username and password is admin admin 52 Dinstar Technologies Co Ltd DINSTAR DAG Series FXO Voice Gateway User Manual Password Modification Web Config Old Web Username Old Web Password New Web Username New Web Password Confirm Web Password Telnet Config Old Telnet Username Old Telnet Password New Telnet Username New Telnet Password Confirm Telnet Password Figure 4 11 7 Password Modification Interface 4 11 8 Factory Reset Click Apply to restore the factory settings Factory Reset Click the button below to resetto factory default settings Apply Figure 4 11 8 Factory Reset Interface 4 11 9 Device Restart Click the Save button in the Configuration page to save the changes to the equipment configuration The following screen confirms that the changes are saved If the cha
11. Primary Secondary Display Name From Alice lt sip alice atlanta com gt tag 1928301774 Here Bob and Alice is the display User account information provided by VoIP service Primary Secondary SIP User ID provider ITSP Usually in the form of digit similar to phone number or actually a phone number SIP service subscriber s Authenticate ID used for Primary Secondary Authenticate ID Dinstar Technologies Co Ltd DINS TAR DAG Series FXO Voice Gateway User Manual authentication Can be identical to or different from SIP BR eeeeteiegeeggiegefl e It specifies the policy for selecting port in a port group e Ascending the system always selects a port from the minimum number The preferential selection of the port can be realized through this mode Cyclic ascending when system selects ports Priority it always begin from the number next to the number selected last time if the maximum priority number is selected last time then the next number is the minimum Port Select priority number and move in cycles like this Descending when system selects ports priority it always begin to select from the maximum priority number Cyclic descending when system selects ports Priority it always begin from the number before to the number selected last time if the minimum priority number is selected last time then the next number is the maximum priority number and move in cycles like this e Group ring all ports rin
12. Timeout for answer Incoming call This timer set how long the phone sets ringing when get incoming call gt No RTP Detect This option is to disconnect call when there is no RTP received Default value is 90s Incoming call setting and Caller ID Incoming Call from PSTN Configuration by FXO Enable Detect CID send Original CID when Call from PSTN Enable Format of From field when CID is Available Format of From field when CID is Unavailable Display User Ib CID Calling Number Name Calling Name FXO Keep Onhook until Callee Answered L Enable Play Hint to FXO Enable Allow Callto SIP Server without Registration Enable gt Configuration by FXO When the call from FXO interface users can be enable or disabled FXO allocation function FXO configuration function includes detect CID Send original CID Play hint to 26 Dinstar Technologies Co Ltd DINS TAR DAG Series FXO Voice Gateway User Manual FXO gt Detect CID to enable caller ID detection for incoming calls The gateway has two modes Before ring and after ring Before ring the FXO port will detect CID first then ringing to the port It takes about few seconds to detect CID in generally After ring the FXO port will ringing to FXO port then start to detect CID gt Send Original CID when Call from PSTN From Mode when CID Is Available Used to configure From Mode when Caller ID Is Available when call from PSTN to VoIP The SIP header should be matched w
13. default is 1800s 23 Dinstar Technologies Co Ltd DINS TAR DAG Series FXO Voice Gateway User Manual Heartbeat Heartbeat message detect the connection status between device and SIP server Secondary SIP Server IP l l l l i Backup SIP Server s IP address or Domain name provided by VoIP service provider address Secondary SIP Server port Service port default is 5060 protects registrar against excessively frequent registration refreshes Secondary SIP server l l l l l l while limiting the state Every once in a while send request for registration to the Register interval l l terminal server default is 1800s Secondary SIP heartbeat Heartbeat message detect the connection status between device and SIP server Use Random Port Random SIP service ports for DAG Set Local SIP port Default SIP service port is 5060 4 7 Port Configuration Port parameters include Send gain receive gain primary display name etc Port Add Port Tx Gain Rx Gain Primary Display Name Primary SIP UserID Primary Authenticate ID Primary Authenticate Password secondary Display Name Secondary SIP User ID Secondary Authenticate ID secondary Authenticate Password Offhook Auto Dial Auto Dial Delay Time Note Offfook Auto Dial will not take effect when dialing is detetecd in the Auto Dial Delay Time Figure 4 7 1 Port configuration interface Port parameters introduce as follows 24 Dinstar Technologies Co Ltd
14. fax mode default If the service provider does not support T 38 pass through mode may be used If you have problems with sending or receiving Fax toggle the Fax Tone Detection Mode setting 3 Local IVR Operation 3 1 Inquire IP address Analog phone connected with FXS ports of device then pick up after dial tone dialing 158 to inquire LAN port IP address and dialing 159 to inquire WAN port IP address 3 2 Factory Reset After picking up dial 166 000000 then onhook and restart after Setting successful 3 3 Configure LAN Porte IP Address Before configuration please ensure 1 The device is power on 2 deviceis connectingto network 3 Telephone is connecting to FXS port of device 1 Configure dynamic IP address by DHCP Offhook Dial 150 2 Onhook If the equipment hint success after 10 seconds and restart the equipment Power off then power on 2 Configure Static IP address Offhook Dial 150 1 Onhook Then configure IP and mask as follow e Configure IP address Dinstar Technologies Co Ltd DINSTAR DAG Series FXO Voice Gateway User Manual Offhook input 152 172 16 0 100 onhook e Configure subnet mask Offhook input 153 255 255 0 0 onhook e Configure gateway IP address Offhook input 156 172 16 0 1 onhook 3 Query the IP address of device Offhook input 158 4 If the DAG serial uses PPPoE method to get IP address it need to conf
15. function FXO port directly sent the dial number without call extension gt Dial Delay Timer of outgoing call dialing To call out while match with routing rule successfully gt Polarity Reversal Detect To enable or disable Polarity Reversal gt Delay Time after FXO Offhook Timer of the gateway to send SIP 2000K to VoIP In case the fixed line doesn t supply answer signal the gateway will send answer signal to VoIP side Onhook when Busy Tone Detected Enable No Current Detected _ Enable Current Disconnect Threshold 200 ms DC Impedance 50 Ohm K AC Impedance 600 Ohm ww Automatch FXO Impedance gt Busy Tone Detected The FXO port will release while busy tone detected gt No current detected The FXO port will release while no current detected on the phone line gt AC DC impedance To match with the impedance of phone line automatically or configure impedance manually Here is the list that support on the gateway 28 Dinstar Technologies Co Ltd DINSTAR DAG Series FXO Voice Gateway User Manual SU nm 270 Ohm 750 Ohml 150 nF and 275 Ohm 780 Ohml 150 nF 220 Ohm 820 Ohml 120 nF and 220 Ohm 820 Ohml 115 nF 370 Ohm 620 Ohml 310 nF 320 Ohm 1050 Ohml 230 nF 370 Ohm 820 Ohml 110 nF 275 Ohm 780 Ohml 115 nF 120 Ohm 620 Ohm 110 nF 350 Ohm 1000 Ohm 210 nF 200 Ob GOU Ohm 100 nF 600 Ohm 16 uF 900 Ohm 1 uF 900 Ohm 16 uF 600 Ohm 1 uF Global Complex Impedance 4 8 2 Media
16. these segments the static route need to be configured Static Route configuration interface as follows Static Route Table Dest IP Address Subnet Mask Nexthop Enable rr ee 2 3 d eee 5 6 8 D R E KKK Figure 4 5 8 Static route configuration interface 21 Dinstar Technologies Co Ltd DINSTAR DAG Series FXO Voice Gateway User Manual 4 5 8 ARP ARP brief introduction ARP is address resolution protocol After configuring ARP users can get physical address through device IP address Under TCP IP network environment each host is assigned a 32 bit IP address But the message transmission needs to know the purpose the physical address of the party ARP is a tool that converts IP address into MAC address ARP configuration interface as follows Static Dynamic Figure 4 5 4 ARP Parameters 4 6 SIP Server SIP server introduction 1 SIP server is the main component of VoIP network and responsible for establishing all the SIP phone calls SIP server also called SIP proxy server or registered server IPPBX and the soft switch can act as SIP server role 2 Usually SIP server does not participate in the media process In SIP network the media always using end to end to hand the consultation In some particular situation or business processing such as Music On Old SIP server will actively participate in the media negotiation Simple SIP server is responsible only for establishm
17. DINS TAR DAG Series FXO Voice Gateway User Manual Note The device must restart to take effect Figure 4 5 1 Local network Link Speed amp Duplex used to select Ethernet port work mode include 5 kinds of Choice Auto Detect 10Mbps half duplex 10Mbps full duplex 100Mbpshalf duplex 100Mbps full duplex default is Auto Detec e When select Obtain IP address automatically DAG will obtain IP address by DHCP When select Use the following IP address that configure DAG to fixed IP address mode When select PPPoE please fill in account and password offered by ISP in internet account and password Notes 1 If select DHCP to obtain IP address please ensure DHCP server in network and work normally 2 After configuration restart device configuration validation 3 Dinstar Technologies Co Ltd DINSTAR gt Route Mode Network configuration of route mode Network Mode WAN Port Link Speed amp Duplex Obtain an IP address automatically Use the following IP address IP Address subnet Mask Default Gateway PPPoE Account Password Service Name WAN MTU LAN Fort Link Speed amp Duplex IP Address Subnet Mask LAN MTU DNS Server Obtain DNS server address automatically Use the following DNS server address Primary DNS Server Secondary ONS Server DAG Series FXO Voice Gateway User Manual Route Bridge Auto Detect
18. DP over NATs is a network protocol It allows users back of NAT find their own public network address NAT type and internet end port have been bound by NAT for a local port Two back of NAT router devices established UDP communication through this information STUN doesn t support TCP connection and H 323 2 NTP Network Time Protocol NTP is a computer time synchronization protocol System parameter configuration interface as follow System Parameter enable Enable Primary NTF Server Address us poolntp org Primary NTP Server Port d secondary NTF Server Address Secondary NTP Server Port SYN Interval Time one GMT 6 00 US Central Time Chicago Daily Reboot Reboot Time WEB Parameter WEB Port Access WEB by WAN Enable Telnet Parameter Telnet Port Figure 4 8 11System Configuration Interface 39 Dinstar Technologies Co Ltd DINSTAR STUN Server Address STUN Server Port Primary NTP server address Primary NTP server port Secondary NTP server address Secondary NTP server port SYN Interval Time Zone Reboot time WEB Port Access Web by WAN Telnet Port 4 9 Call amp Routing 4 9 1 Port Group DAG Series FXO Voice Gateway User Manual STUN server IP address STUN server port Primary NTP server IP address system default is us pool ntp org Default is 123 Default is 18 145 0 30 Default is 123 Every certain time synchronization gateway time the system default every 3600
19. Gateway Optional 192 168 11 77 Primary ONS Server Optional 202 96 126 66 secondary ONS Server Optional 202 96 134 133 Note The device must restart to take effect Figure 4 5 5 DHCP Configuration Interface Note When configure start and end IP address subnet mask and gateway please set the same segment with LAN port Otherwise device will not work normally After configuration restart device configuration validation 4 5 5 DMZ Host Routing mode DMZ Demilitarized Zone connect web e mail etc server allowed external to access to this area Make the internal network located the back of the zone of confidence and not allow any access separation of inside and outside the network protect user information DMZ can be understood that a special areas of the network and different from the external network or intranet Public server that does not contain confidential information usually placed in DMZ such as web Mail FTP etc Accuser from intranet can visit the service of DMZ but can t come into contact with confidential or private information stored in the network Even if DMZ server is damaged it will not be confidential information in the internal network 19 Dinstar Technologies Co Ltd DINSTAR DAG Series FXO Voice Gateway User Manual DMZ Host DMZ Host IF Address Enable Note The IP address needs to be in the same subnet with LAN port Figure 4 5 6 DMZ Configuration Interface Note After confi
20. IP Tel Parameters Configuration Index Routing priority 0 31 0 is the highest priority its purpose is so you can identify the routing with a meaningful name Calls From Tel IP call select port or port group Caller number Prefix its length normally less or equal to caller number which helps to matching routing exactly if caller number is 2001 the caller Caller Prefix l l prefix can be 200 or 2 any means match any caller number like bob1 29801 Called number Prefix its length normally less or equal to called number which helps to matching routing exactly if called number is 008675526456659 the called prefix can be 0086755 or 00 any means Callee Prefix match any called number Calls to This call routing is routing to port port group IP trunk and SIP server 45 Dinstar Technologies Co Ltd DINSTAR DAG Series FXO Voice Gateway User Manual 4 10 Manipulation Configuration 4 10 1 IP Tel Callee IP gt Tel Callee Add Index 31 Calls from IP Trunk 9 SIP Server Caller Prefix Po Callee Prefix Po Calls to 9 Port Port Group stripped Digits fram Left Stripped Digits from Right Prefix to Add Suffix to Add Number of Digits to Leave fram Right NOTE any in Callee Prefix or Caller Prefix means wildcard string Figure 4 10 1 IP Tel Callee number configuration Calls From This call come from IP trunk or SIP server Caller number Prefix its length normally less o
21. One stage dialing After receiving phone number from softswitch IPPBX selected one PSTN call out through some selection rules such as round of selection e Two stage dialing IPPBX extension dial FXO port SIP account then after hearing dial tone dial outside number 2 Dial the number directly and press e Dial outside number with FXO when listen to audio please dial the extension number or second dial tone and then dial callee number After dialing completion send callee number to IP server side such as soft switch or IPPBX e Offhook auto dial Dial outside number with FXO device will automatically connect to the specified extension or queue according to the default hotline number 2 1 2 Direct IP Calls DAG series device with FXS port allow two parties directly call through IP address The user need only a simulation with the FXS port unit equipment linked together and set up calls not registered Elements necessary to completing a direct IP call 1 Both DAG serial and other VoIP Device have public IP addresses Dinstar Technologies Co Ltd DINSTAR DAG Series FXO Voice Gateway User Manual 2 Both DAG serial and other VoIP Device are on the same LAN using private IP addresses 3 Both DAG serial and other VoIP Device can be connected through a router using public or private IP addresses with necessary port forwarding or DMZ Operation Process 1 Pick up the analog phone then dial 47 2 Enter th
22. P Inquiry WAN IP Inquiry Phone Number Setting IP Mode Network Work Mode Configure IP Address Network Subnet Mask Configure Network Gateway Configure Renew DHCP Access WEB by WAN in Route Mode Reset Factory Restart Device Call Function Call Onhold Offhald Call by IP Call Waiting Activate Call Waiting Deactivate Blind Transfer Call Forward Unconditional Activate Call Forward Unconditional Deactivate Call Forward Busy Activate Do Not Disturb Activate Do Not Disturb Deactivate Dial Voicemail Dinstar Technologies Co Ltd 4 4 ech lf sall all s al all 5 ec Al ee ri Sl se SE if GEIER 193 ali 4 2 alt alt ai a alt ali a 4 J oo in j cn E FE Ma j oj j D Er eI i Ft St a g S Q 0 WC WC ZUUS BE Note Please finish dialing the feauture code within 2s when using the Call holding function Figure 4 8 10 Feature Code Configuration Interface Use Default Sisi GER JESS SS ses Status Enable Le Enable Le Enable Le Enable e Enable e Enable e Enable Le Enable Le Enable e Enable e Enable e Enable w Enable v Enable w Enable Enable w Enable Enable Enable 37 DINS TAR DAG Series FXO Voice Gateway User Manual Inquire WAN port IP address Dial 159 to obtain device WAN port IP address Inquire Phone Number Dial 114 to obtain po
23. Parameter Media parameter mainly include RTP start port DTMF parameter PreferedVocoder Configuration Interface as follow Media Parameter RTP Start Port DIMF Parameter DTMF Method SIGNAL DTMF Gain DTMF Send Interval ms Prefered Vocoder Coder Name Payload Type Packetization Time ms Rate kbps Silence Suppression 1st 2 2nd 2 2 3rd 2 3 Figure 4 8 2 Media Parameter Configuration Interface Media parameter description RTP Start Port Default RTP port 8000 DTMF Method SINGAL INBAND RFC2833 It is configurable When RFC2833 is selected RFC2833 Payload Type Optimization payload negotiation parameter with remote side it includes two options Local and remote 29 Dinstar Technologies Co Ltd DINSTAR DAG Series FXO Voice Gateway User Manual RFC2833 Payload Type Payloadvalue default is 101 DTMF Gain Default is 0 DB DTMF Send Interval DTMF send signal interval default is 200ms DAG supports G729 G711U G711A G723 while Coder Name it make outgoing call G 729 will used as figure 4 8 2 displayed Each kind of coding has a unique type load Payload Type value refer toRFC3551 Packetization Time Voice package time Default is disable if enable according to the current noise environment dynamically adjust mute inhibit threshold thus in the user in silent state stop transmission background noise bag and save about VoIP bandwidth In the low bandwidth environment can reduce the network cong
24. Regeneration Table for the reception Port 2 802 1p IEEE 802 1p standard Traffic class expediting and dynamic multicast filtering It describes important methods for providing QoS at MAC level IEEE 802 1p is in fact quite good Lower priority level packets are not sent if there is packets in queued in higher level queues IEEE 802 1p describes no admission control protocols It would be possible to give Network Control priority to all packets and the network would be easily congested There are three VLAN data VLAN voice LAN and management VLAN VLAN configuration interface as following figure 4 4 3 16 Dinstar Technologies Co Ltd DINSTAR DAG Series FXO Voice Gateway User Manual VLAN Config Data VLAN E Enable Data 302 10 VLAN ID 0 4095 Data 802 1P Priority 0 7 In this case data VLAN use the default WAN interface Voice VLAN E Enable Voice 802 10 VLAN ID 0 4095 Voice 802 1P Priority 0 7 Voice VLAN use following separate IP interface DHCP Static IP IP Address Subnet Mask Default Gateway Management VLAN E Enable Management 302 10 VLAN ID 0 4095 Management 802 1P Priority 0 T Management VLAN use following separate IP interface DHCP Static IP IP Address Subnet Mask Default Gateway Note The device must restart to take effect Figure 4 5 3 VLAN parameter configuration Table 4 5 1VLAN parameter configuration Fill out an ID to describe a data VLAN group ID 0 Data
25. ddress from the first DHCP server it discovers from the LAN it is connected Using the PPPoE feature set the PPPoE account settings The DAG willestablish a PPPoE session if any of the PPPoE fields is set WAN Port Static IP mode configure the IP address Subnet Mask Default Router IPaddress DNS Server 1 primary DNS Server 2 secondary fields These fieldsare set to zero 11 Dinstar Technologies Co Ltd DINS TAR DAG Series FXO Voice Gateway User Manual LAN Port DNS Server System Uptime Network Traffic Statics Version Fort Registration Information Port Group Registration Information O lt All Portz 0 1 2 3 4 5 6 7 6 9 10 11 12 13 Unregistered Refresh Figure 4 3 2 Port and Port group registration information 4 3 3 TCP UDP Statistics TCP UDP Traffic 232 59 41 216 Figure 4 3 3 TCP UDP Statistics Information Figure 4 3 3 shows TCP sending and receiving UDP sending and receiving packets of Statistical information since the device launched Dinstar Technologies Co Ltd DINSTAR DAG Series FXO Voice Gateway User Manual 4 3 4 RTP Session Statistics RTP Session Figure 4 3 4 RTP Session Statistics Figure 4 3 4 display real time RTP conversation flow data information includes Port voice codec packet period local port peer IP peer port sent packets receive packets lost packets jitter and duration 4 4 Quick Setup Wizard Quick configuration guide
26. e target IP address Note No dial tone will be played between step 1 and step 2 Examples If the target IP address is 192 168 0 160 the dialing convention is 47 then 192 168 0 160 Followed by pressing the key or wait 3 seconds Complete Signaling interactive soon after he was called the unit can be heard ringing Note You cannot make direct IP calls between FXSO to FXS1 since they are using same IP It only supports the default destination port 5060 2 2 Call Features DAG FXS support all traditional and senior phone function Table 2 2 1 Feature Codec Feature Codec Operation Instructions Dinstar Technologies Co Ltd DINSTAR DAG Series FXO Voice Gateway User Manual 90 Enable Busy Call Forward 91 Disable Busy Call Forward 92 Enable No Answer Call Forward Disable No Answer Call Forward 78 Enable DND Disable DND 200 Access Voice mail Switch between incoming calls If not in session flash hook will switch a Flash Hook new channel for new call 2 3 Sending and Receiving Fax 2 3 1 DAG FXS support four fax modes 1 T 38 FoIP 2 Pass Through 3 Modem 4 adaptive Dinstar Technologies Co Ltd DINS TAR DAG Series FXO Voice Gateway User Manual 2 3 2 T 38 and Pass Through T 38 is the preferred method because it is more reliable and works well in most network conditions If the service provider supports T 38 please use this method by selecting T 38 as
27. ent maintenance and cleaning conversation don t interfere in call While relatively complex SIP server also called SIP PBX It not only provides the basic call and basic conversational support also offer plenty of business such as Presence Find me Music On Hold 22 Dinstar Technologies Co Ltd DINSTAR DAG Series FXO Voice Gateway User Manual 3 SIP server based on Linux platform such as OpenSER sipXecx VoS Mera etc 4 SIP server based on windows platform such as miniSipServer Brekeke VoIPswitch etc 5 Carrier grade soft switch platform such as Cisco Huawei Zteetc SIP server configuration interface as follows SIP Server Primary SIP Server Primary SIP Server Address 172 16 65 20 Primary SIP Server Port Default 5060 Register Interval Default 1600 0000 5 Heartbeat Enable Secondary SIP Server Secondary SIP Server Port Default 5060 5060 Register Interval Default 1600 1800 Heartbeat E Enable Local SIP Port Use Random Port Enable set Local SIP Port 5060 Figure 4 6 1 SIP Server Configuration Interface SIP parameter description Primary SIP Server IP SIP Server IP address or Domain name provided by VoIP service provider Primary SIP Server port Service port default is 5060 protects registrar against excessively frequent registration refreshes Register interval while limiting the state Every once in a while send request for registration to the terminal server
28. estion greatly improving VoIP call effect Slience Suppression 30 Dinstar Technologies Co Ltd DINSTAR 4 8 3 SIP Parameter SIP Parameter SUBSCRIBE for MiWVi Message Waiting Indicator Voicemail UserID RTF Mode in SDP when Call Holding IP to IP Call URI includes user phone Only Accept Calls from Server Anonymous Call Reject Anonymous Call as Ending Dial Key PRACK Value of Refer To refers to Contact Domain Query Type T1 T2 T4 Max Timeout Heartbeat Intervali 3600s Figure 4 8 3 SIP Parameter Configuration Interface SIP parameter description Voicemail message indicator it is to be realized in the SUBSCRIBE for MWI way of NOTIFY Voicemail User ID Access code to voicemail box When call come into holding if select to receive and not send packet then the local can hear call waiting tone If select to RTP Mode in SDP when Call Holding not receive and not send packet then doesn t play call waiting tone Enable this function users may use the business call IP IP to IP Call address on the phone SIP carries the information the system defaults not open Default is no it indicates the DAG accept incoming call from Only Accept Call from Server SIP server only 31 URI Includes user phone Dinstar Technologies Co Ltd DAG Series FXO Voice Gateway User Manual E Enable Po sendonly E Enable E Enable E Enable E Enable E Enable Enab
29. eway User Manual 4 9 4 IP Tel Routing IP gt Tel Routing Add Index 31 Description PO Calls from wtunk Any Le SIP Server Caller Pretix po Callee Prefix Calls to Po oe Poter T NOTES any in Callee Prefix or Caller Prefix means wildcard string Figure 4 9 4 IP Tel Routing Parameter Routing priority 0 31 0 is the highest priority o its purpose is so you can identify theIP0 gt Tel routing with a Description l meaningful name Calls from IP Trunk SIP Server any means any IP Caller number Prefix its length normally less or equal to caller l number which helps to matching routing exactly if caller number is Caller Prefix l 2001 the caller prefix can be 200 or 2 any means match any caller number like bob1 29801 Called number Prefix its length normally less or equal to callednumber which helps to matching routing exactly if called number is 008675526456659 the called prefix can be 0086755 or Callee Prefix 00 any means match any called number Calls to This call routing is routing to port or port group 44 Dinstar Technologies Co Ltd DINSTAR DAG Series FXO Voice Gateway User Manual 4 9 5 Tel IP Tel Routing Tel IP Tel Routing Add Index 31 Description Calls from Por PortGroup __I Calls to Por PotGroup emm Tey SIP Server NOTES any in Callee Prefix or Caller Prefix means wildcard string Figure 4 9 5 Tel
30. ging at the same time Press extension number to decide which extension Pick Up on Group on the phone 4 9 2 IP Trunk A peer to peer VoIP call occurs when two VoIP phones communicate directly over IP without IP PBXs between them A peer to peer call can be initiated directly by dialing destination phone number in DAGs and also receiving incoming calls from other peer to peer gateway IP trunk is help to DAGs establish peer to peer call between DAGs and other VoIP phones IP trunk will be used in routing configuration 42 Dinstar Technologies Co Ltd DINSTAR DAG Series FXO Voice Gateway User Manual IP Trunk Add Index Description Remote Address Remote Port Heartbeat Figure 4 9 2 IP Trunk Configuration Interface IP trunk number it is range from 0 to 63 o The description of IP trunk its purpose is so you can identify the IP trunk with Description a meaningful name Remote Address Peer IP address or domain name Remote Port Peer SIP port Heartbeat Default is disable if enable DAG will send OPTION to peer device 4 9 3 Routing Configuration Figure 4 9 3 Routing Parameter Configuration Interface Routing Parameter Calls from IP Routing before Manipulation Calls from Analog Line Routing before Manipulation This option determines the following routing of call take effect before or after manipulation 43 Dinstar Technologies Co Ltd DINSTAR DAG Series FXO Voice Gat
31. guration restart device configuration validation 4 5 6 Forward Rule Routing mode In some cases LAN network equipment need to provide some communication in WAN network such as port for 21 FTP service This time can be configured forwarding rules for the network equipment Service ports namely the need to provide service network mouth WAN ports IP address that LAN network provide services to the mouth of the network equipment IP address the protocol is TCP or UDP The different between forward rule and DMZ host is that DMZ Host offers continuous multiple Port 0 1024 and all the foreign communication agreement while the forward rule offers a single or a few port foreign communication on some protocol When the conflicts exist between forward rule and DMZ host the configuration of forwarding rules is preferred Forward rule configuration interface as follows 20 Dinstar Technologies Co Ltd DINSTAR DAG Series FXO Voice Gateway User Manual Forward Rule Table Server Port IP Address Frotocol Enable C G an on on amp w wN Notes 1 IP Address needs to be in the same subnet with LAN port 2 Server Port range 0 65535 Figure 4 5 7 Forward rule configuration interface 4 5 7 Static Route Table Static Route Table is IP communication direction in network generally do not need to configure static route When there are many segments in LAN network and need to complete some specific application among
32. hen input IP address of device Dress Enter it pop up logging on identity authentication interface Authentication Required LZ The server 172 16 77 10 80 requires a username and password The server says Web Config System User Name admin Password cancel Figure 4 1 1 DAG FXS Login Interface Default username and password admin admin click OK to entry into web interface Dinstar Technologies Co Ltd DINSTAR DAG Series FXO Voice Gateway User Manual D DINSTAR Web Management System System Information Status amp Statistics Quick Setup Wizard MAC Address 00 12 34 56 78 00 Network Network Mode Bridge SIP Server IP Address 172 16 22 222 255 255 0 0 Port 172 416 1 1 Advanced Call amp Routing DNS Server 202 96 128 68 202 96 134 133 Manipulation j System Uptime Oh 01m 36s Maintenance y p NTP Status Succeed Network Traffic Stat Received 1711574 bytes Sent 30170 bytes Version DAG1000 80 Rev 2 11 08 05 PCB 23 1 LOGIC 0 BIOS 1 Built on Nov 30 2013 15 12 09 Hint Language English Figure 4 1 2 DAG Configure Interface 4 2 Navigation Tree DAG series voice gateway web configuration interface mainly includes navigation tree and the right configuration interface Choose navigation tree in order to entry into the configuration interface Status amp Statistics Quick Setup Wizard Network SIP Server Port Advanced FXS FXO Media Parameter SIP Parameter Fax Parameter
33. hereinafter referred to as the DAG series FXS analog voice gateway DAG series FXO analog gateway is access gateway based on IP network It can provide low cost simple operation VoIP solutions for small enterprise the family office remote office and branch enterprise DAG connects to analog telephone fax and traditional analog PBX with standard voice interfaces and provided high quality voice service DAG series VoIP access gateway adopted standard SIP protocol and compatible with leading IP PBX soft switch and SIP based platform DAG series FXS analog gateway includes following model m DAG1000 40 E DAG1000 80 DAG1000 160 This manual mainly to DAG2000 160 as example introduce the function of devices and parameter configuration 1 2 Equipment appearance Figure 2 1DAG2000 80 Figure 2 2DAG2000 160 Dinstar Technologies Co Ltd DINSTAR DAG Series FXO Voice Gateway User Manual 1 3 Power supply DAG1000 4 80 is Cassette equipment with placed on desk and adopts AC 110 240 V power supply with the power adapter convert to 12VDC power Power parameters Input 100 240V 50 60Hz Output 12VDC Notes Because power adapter interface is different in different country please confirm the interface standard with us before shipment 1 4Network Applications All over the world PC IP LAN DAG1000 80 FXO lines FXO olP access gateway DAG1000 8S lt IP Network rar FXS
34. i A T 11 4 3 2 Registration Information 12 4 3 3 TCP UDP Eelere eegene ee 12 e GE SESSION RAE e 13 4 4 QUICK Setup Wizard ccc ccessscecesscecessececessececessesecessesecesssesecessesesessases 13 AS NETWOLF CONG UTAO EEN 13 4 5 1 Beie Ne OMG EE 13 FSL VLAN Paramete ee 15 4 5 3 MAC Clone Routing mode 18 4 5 4 DHCP Server Routing mode 18 4 5 5 DMZ Host Routing mode 19 4 5 6 Forward Rule ROUtING mode 20 457 Statie ROUE E LC 21 4 5 8 EE 22 SE E e GEN 22 AP POLE KEE 24 e Be E nen EE 25 PPS lis Ne EE 25 4 8 2 Media ParaMete rn eececcccesssssssssssseeeeceeeecceeceesesesssssssessstanees 29 A ER Een 31 Ee Paramete ge ne a 34 AOD DIGIT IMA EE 35 Eege 37 4 8 7 SYSTEM Parameter cscccsccussssscsssccersssssousccusssnscenseerseuscouseerseens 39 Ai Calli le Le EE A0 EE EE A0 PDD TP ta Un 42 49 3 ROULNG COMMGUPALION E 43 49 4 Ee ROUTING Eege 44 49 5 Tel 1P Vel ROUN Gerari a a 45 4 10 Manipulation Configuration ccc ecccccssseceesseceesseceesseeessseeessseeesseeens 46 SE Me allee e ee 46 e Dahn fel Ca TEEN 47 ATO E e WEE 48 aL ET ne RE 48 Ae o SYSIOG Be EE 48 4 11 2 Firmware Upload 49 Ao Wie NEE aC ID 50 ALLA Data RESTOrG ee 50 SRNO EE 50 AALO Macerl E EE 51 4 11 7 Password Modification 52 e GE Factory WEE 53 Al 9 Device RE 53 Ee GT 54 DINS TAR DAG Series FXO Voice Gateway User Manual 1 Equipment Introduction 1 1 Overview Thanks for purchasing Dinstar DAG
35. igure by web browser Note The telephone will play voice prompt Setting successfully if the step is correct 4 WEB Configuration 4 1 WEB Login Device is connecting to network properly refer to chapter 3 Operation Offhook and dial 158 to inquire device IP address 4 1 1 Login Device LAN port default IP address is 192 168 11 1 WAN port default obtain IP address by DHCP Advice to modify the IP address of the local computer equipment and ensure that are on the same IP segment with Windows 7 as an example the local computer IP address change for 192 168 11 10 Dinstar Technologies Co Ltd DINSTAR DAG Series FXO Voice Gateway User Manual Internet Protocol Version 4 TCP IPv4 Properties em You can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for the appropriate IP settings A Obtain an IP address automatically Use the following IP address IP address Subnet mask Default gateway Obtain DNS server address automatically Use the following DNS server addresses Preferred DNS server Alternate DNS server E Validate settings upon exit Figure 4 1 1Modify IP address Check connection between computer and device click Start gt run gt input cmd run ping 192 168 11 10 t order to check the connectivity between them 4 1 2 Login WEB Open web browser t
36. ith follow formats Display CID From Mike lt sip CID host com gt tag 51088abb User ID CID From 201 lt sip CID host com gt tag 51088abb CID CID From Caller ID lt sip Caller ID host com gt tag 51088abb CID User ID From Caller ID lt sip 201 host com gt tag 51088abb e From Mode when Caller ID Is Unavailable Used to configure From Mode when Caller ID Is Unavailable Anonymous From lt sip Anonymous host com gt tag 51088abb Display User ID From Mike lt sip 201 host com gt tag 51088abb gt Keep onhook until callee answered When the gateway get incoming call from PSTN network the modular will answer the call then start to DIMF or route to destination hotline number While this option enabled the modular won t answer the call but routing to destination hotline number till it getting answer gt Play Hint to FXO Enable this function when call from PSTN to FXO port FXO port will play prompt tone please dial the extension number gt Allow Call to SIP Server without Registration To enable peer to peer call without registration Outgoing call Parameters 27 Dinstar Technologies Co Ltd DINSTAR DAG Series FXO Voice Gateway User Manual Outgoing Call to PSTN One Stage Dialing Enable Hook Flash Enable Dial Delay ms Answer to Caller when Polarity Reversal Detected L Enable Delay Time after FXO Offhook ho dp Dial Mode DTMF gt One Stage Dialing Enable this
37. itional gateway set law Because IP address binding in only a legitimate MAC address by ISP If the ISP s switch discover illegal MAC address it will refuse service The best way is MAC clone for MAC binding Most ADSL MODEM broadband router wireless router have this feature The principle of MAC address clone is deliberately exposed MAC address of bound computer to the ISP server and let the ISP server think that used only a single piece of computer in fact many computers in sharing the Internet This function used to prevent ISP limiting to share the Internet Note restart device to take configuration effect 4 5 4 DHCP Server Routing mode Under route mode DAG network part as a small router to configure DHCP service that DAG as a DHCP server in network Start and end address of address pool determine the range of IP address automatically assigned to other devices e IP Expire Time means use time of assigned IP address More than the lease time if the IP address is not used by network equipment IP address will be recovered 18 Dinstar Technologies Co Ltd DINSTAR DAG Series FXO Voice Gateway User Manual e Subnet mask gateway DNS and other information configured by DHCP protocol Configuration interface as figure 4 5 5 DHCP Server Config DHCP Server Enable IF Pool Starting Address 192 166 771 100 IP Pool Ending Address 192 168 11 199 IP Expire Time Subnet Mask Optional 255 2755 2755 0 Default
38. ix and change it as necessary Its default feature codes setting as below Voicemail Dial Voicemail My Voicemail Figure 4 8 5 Elastix Voicemail Setting SIP Parameter SUBSCRIBE for MWi Message Waiting Indicator lEnable Voicemail User ID Figure4 8 6 Voice Mail Setting In SIP Parameter 3 Enable voice mail in DAG and Elastix will ask you to leave a message after ringing 15 seconds then Elastix will record and display your message 33 Dinstar Technologies Co Ltd DINS TAR DAG Series FXO Voice Gateway User Manual Voicemail Ringtime Default 15 Direct Dial Voicemail Prefix S Direct Dial to Voicemail message type Unavailable v Optional Voicemail Recording Gain Do Not Play please leave message after tone to caller a Figure 4 8 7 Voicemail Setting 4 DAG dial 200 then dial voicemail account and thenask password for Validation After that the user will hear voice message 4 8 4 Fax Parameter Fax introduction DAG fax parameter includes fax mode Fax sound detection party ECM Rate Fax Config Mode T38 Le Tone Detection by Auto Je ECM Enable fall Rate 14400 bps e Figure 4 8 8 Fax Parameter Configure Interface Fax parameter description Fax mode support T 38 T 30 Pass through Modem Adaptive Tone Detection by Fax sound detection mode Caller Callee Automatic Fax error correction information The rate of sending and receiving 34 Dinstar Technologies Co
39. le E Enable E Enable A Query DINS TAR DAG Series FXO Voice Gateway User Manual Enable anonymous call anonymous will include in SIP Anonymous Call message l Enable this function reject all anonymous call Disable by Reject Anonymous Call deg efau as ending Dial Key Dial up use as a end descriptor RFC3262 defined an optional extension methods PRACK provisional ack Used to support the reliability of the temporary response Its function is to require the receiving partycontact with the third partythrough the use of supplied in the request in the Value of Refer To refers to Contact l l l p address information Refer to field of SIP message fill in contact header Default is A QUERY Voice mail instructions Here DAG work with Elastix the example introduces how voicemail work in DAG 1 DAG register to Elastix server Corresponding extension number enable voice mail function in Elastix and set password As below 32 Dinstar Technologies Co Ltd DINSTAR DAG Series FXO Voice Gateway User Manual Voicemail amp Directory Status Enabled Voicemail Password 111111 Email Address Pager Email Address Email Attachment C yes Play CID yes Play Envelope yes Delete Voicemail C yes IMAP Username IMAP Password VM Options VM Context default VmX Locater Figure 4 8 4 Elastix Voicemail Configuration Interface 2 check feature code in Elast
40. n square brackets CT and but only one can be selected 3 Range One or more expressions enclosed between round brackets and but only one can be selected 4 Separator Separated expressions or DTMF symbols 5 Subrange Two digits separated by hyphen which matches any digit between and including the two The subrange construct can only be used inside a range construct i e between and J 6 Wildcard x matches any digit COU to 9 7 Modifiers Match 0 or more times 8 Modifiers Match 1 or more times 9 Modifiers Match 0 or 1 times Example Assume we have the following digit maps 1 XXXXXXX x11 and a current dial string of 41 Given the input 1 the current dial string becomes 411 We have a partial match with xxxxxxx but a complete match with x11 and hence we send 411 to the Call Agent 2 2 8 XXXXXX 13XXXXXXXXX Means that first is 2 3 4 5 6 7 or 8 followed by 6 digits 36 Dinstar Technologies Co Ltd DINSTAR or first is 13 followed by 9 digits 3 13 15 18 xxxxxxxxx Means that first is 13 15 or 18 followed by 8 digits 4 1 357 9 xx Means that first is 1 2 3 or 5 or 7 8 9 followed by 2 digits 4 8 6 Feature Codec DAG Series FXO Voice Gateway User Manual Feature codec includes device function and call function Feature codec as follow Feature Code Feature Device Function Inquiry LAN I
41. nges need restart reboot or power cycle the equipment to make the changes take effect Restart Click the button below to restart the device Restart Figure 4 11 9 Device Restart 53 Dinstar Technologies Co Ltd DINS TAR DAG Series FXO Voice Gateway User Manual 5 Glossary e DNS Domain Name System e SIP Session Initiation Protocol e TCP Transmission Control Protocol e UDP User Datagram Protocol e RTP Real Time Protocol e PPPOE point to point protocol over Ethernet e VLAN Virtual Local Area Network e ARP AddressResolution Protocol e CID Caller Identity e DND Do NOT Disturb e DTMF Dual Tone Multi Frequency e NTP Network Time Protocol e DMZ Demilitarized Zone e STUN Simple Traversal of UDP over NAT e PSTN Public Switched Telephone Network 54 Dinstar Technologies Co Ltd
42. r equal to caller number which helps to matching routing exactly if caller Caller Prefix l l number is 2001 the caller prefix can be 200 or 2 any means match any caller number like bob1 29801 Called number Prefix its length normally less or equal to called number which helps to matching routing exactly if called Callee Prefix number is 008675526456659 the called prefix can be 0086755 or 00 any means match any called number 46 Dinstar Technologies Co Ltd DINSTAR Number of Digits to Leave from Right 4 10 2 Tel IP Caller Tel IP Caller Add Index Description Calls from Caller Prefix Callee Prefix Calls to Stripped Digits from Lett Stripped Digits from Right Prefix to Add Suffix to Add Number of Digits to Leave fram Right DAG Series FXO Voice Gateway User Manual Suffix to Add Add a number suffix Starting from the right to retain the called number digits 3 Port Port Group pink Any e SIP Server Pd Pd Pd Po po NOTE any in Callee Prefix or Caller Prefix means wildcard string Figure 4 10 2 Tel IP Caller Configuration parameters are the same with IP gt Tel Callee Dinstar Technologies Co Ltd DINSTAR DAG Series FXO Voice Gateway User Manual 4 10 3 Tel IP Callee Tel gt IP Callee Add Index 31 Description Calls from Caller Prefix Callee Prefix Calls to Port Port Group P Trunk An
43. rt account 150 0 means pppmodem 150 1 means static IP Setting IP Mode 150 2 means obtain IP address by DHCP 150 3 means pppoe 157 0 set network work mode to routing mode 157 1 Network Work Mode set network work mode to bridge mode Configure IP Address 152 IP set gateway IP address Network subnet mask configure 153 subnet mask set gateway subnet mask Network Gateway Configure 156 gateway IP set gateway Renew DHCP 193 set dynamic IP again l Allow access web through WAN port 160 1 don t allow Access Web by Wan in Rout Mode access web through WAN port 160 0 Reset Factory 166 000000 reset factory Restart Device 111 restart device When call process dial into call hold Recovery the call Call onhold offhold through hook flash or Call by IP Directly dial the end user IP to call Call Waiting Activate 51 enable call waiting function Call Waiting Deactivate 50 forbid call waiting function l If the call transfer to 801 first hook flash and then dial Blind Transfer the 87 801 Call Forward Unconditional Activate 72 phone number transfer the call from the phone number Call Forward Unconditional 38 Dinstar Technologies Co Ltd DINS TAR DAG Series FXO Voice Gateway User Manual Note Private services are open by default 4 8 7 System Parameter System parameters include STUN NTP Provision WEB parameter Telnet 1 STUN STUN Simple Traversal of U
44. s synchronous once Time zone can be chosen System default the United States central time Chicago Set a restart time for device the device will reboot at this time Gateway web port default is 80 Enable or disable accessing web by WAN Telnet service port default is 23 Port group parameter include Index description etc Port group configure interface as follow Dinstar Technologies Co Ltd 40 DINSTAR DAG Series FXO Voice Gateway User Manual Port Group Add Index Description Primary Display Name Primary SIP UserID Primary Authenticate ID Primary Authenticate Password secondary Display Name secondary SIP User ID secondary Authenticate ID secondary Authenticate Password Offhook Auto Dial Auto Dial Delay Time Port Select Pick Up on Group Port Port O FXQ Port 2 FAQ Port 4 FXO Port DU ZC Port GO XC Port 1 FAQ Port 3 FAQ Port SO SO Port FAQ Port OU XO Port 10 FXO Port 12 FXO Port 14 FxXO Figure 4 9 1 port group configuration interface ad Port groupNumber It uniquely identifies a route range from ndex 0 15 o Port group description its purpose is so you can identify the Description i port group with a meaningful name Port group display which will be used in SIP message Port 11 FX0 Port 13 FX0 Port 15 FXO example INVITE sip bob biloxi com SIP 2 0 Via SIP 2 0 UDPpc33 atlanta com branch z9hG4bK776as dhds Max Forwards 70 To Bob lt sip bob biloxi com gt
45. tes a PABX extension and can realize connection among common phone and a multiplexer It also is FXO interface connected with SPC exchanges FXO as ordinary telephone interface and need to remote provide current FXO may connect company s internal PBX service extension and the telecom outside generally speaking FXO is a telephone So just lead a inside to FXO port from company s internal or directly line a straight up in FXO from the telecom FXO parameters include Call progress Tone Timeout for Dialing Send Polarity Reversal etc Configuration interface as follow Basic Parameters 25 Dinstar Technologies Co Ltd DINSTAR DAG Series FXO Voice Gateway User Manual Call Progress Tone Timeout for Dialing 5 Timeout for Answer QOutgoing Call 5 Timeout for Answer Incoming Call S No RTP Detected Enable Period without RTP Packet 5 gt Call Progress Tone Hear the dial tone when pick up the phone Choose the national standards from the drop down box Default is the United States gt Timeout for Dialing With the help of dialing timeout you can limit the time while users typing the digits from an extension If the timeout expire while the user is typing in the extension then DAG will consider the extension as complete and it will try to send to SIP server Default value is 4 seconds gt Timeout for Answer Outgoing Call This timer set how long the caller party waiting when makes outgoing call on extension gt
46. will guide users to configure the device step by step Users only need to configure network SIP server and sip port in quick setup wizard Basically after these three steps users are able to make voice call through device 4 5 Network Configuration 4 5 1 Local Network DAG has two kinds of work mode route and bridge When DAG is set rout mode the DAG will work as small router and NAT function has enabled In this situation WAN port is normally connect to uplink router switch or ADSL MODEM LAN port used to connect local computer or other network device such as Ethernet switches Hubs etc When DAG is set bridge mode WAN and LAN port are the same The DAG just work as two ports or four ports Ethernet switch When it set to bridge mode only need to configure WAN port IP address and DNS If set to route mode default LAN port IP will display and it can be change by users Note DAG2000 160 just supports bridge mode DAG1000 4 80 supports bridge and route mode Dinstar Technologies Co Ltd gt Bridge mode Network configuration of bridge mode Local Network Network Configuration Link Speed amp Duplex Auto Detect Obtain an IP address automatically Use the following IP address IP Address Subnet Mask Default Gateway PPPoE Account Password Service Name DNS Server Obtain ONS server address automatically Use the following DNS server address Primary DNS Server secondary DNS Server Save
47. y SIP Server stripped Digits from Lett otipped Digits from Right Prefix to Add Suffix to Add Number of Digits to Leave from Right NOTE any in Callee Prefix or Caller Prefix means wildcard string Figure 4 10 3 Tel IPCallee Configuration parameters are the same with Tel gt IP Caller 4 11 Maintenance 4 11 1 syslog Parameter Syslog is a protocol used in TCP IP network transmission of record of the standard file information Syslog agreement belongs to a kind of master slave agreement Syslog sender will sent a small text information less than 1024 bytes to syslog the receiver The receiver are syslogd syslog daemon or syslog server Syslog message can be transferred by TCP UDP 48 Dinstar Technologies Co Ltd DINS TAR DAG Series FXO Voice Gateway User Manual Syslog level e none Used to misarrange e debug Not including function conditions or the question of other information e notice importance common conditions e warning Early warning information e error Stop error conditions of tools or some part of the realization of the function subsystem Syslog Parameter E Enable Figure 4 11 1 Syslog Parameter Configuration Enable send CDR and then send communication information to syslog server 4 11 2 Firmware Upload The process of firmware upload 1 Click Firmware Upload 2 Browse files and choose the loading program Name the file extension Idf
Download Pdf Manuals
Related Search