LAVAMAT 60840 L
Contents
1. Be careful with rust stains which are not recent since the cellulose structure will already have been damaged and the fabric tends to hole Mould stains treat with bleach rinse well whites and fast coloureds only Grass soap lightly and treat with bleach whites and fast coloureds only Ball point pen and glue moisten with acetone lay the garment on a soft cloth and dab the stain Lipstick moisten with acetone as above then treat stains with methylated spirits Treat any residual marks with bleach Red wine soak in water and detergent rinse and treat with acetic or citric acid then rinse Treat any residual marks with bleach Ink depending on the type of ink moisten the fabric first with acetone then with acetic acid treat any residual marks on white fabrics with bleach and then rinse thoroughly Tar stains first treat with stain remover methylated spirits or benzine then rub with detergent paste Detergents and additives Good washing results also depend on the choice of detergent and use of the correct quan tities to avoid waste and protect the environment Although biodegradable detergents contain substances which in large quantities can up set the delicate balance of nature 1 do not use acetone on artificial silk Washing programmes The choice of detergent will depend on the type of fabric delicates woollens cottons etc the colour washing temperature and degree of soiling All commonly2. wash with STAIN option Control panel i Below is a picture of the control panel It shows the programme selector dial as well as the buttons and the pilot lights These are presented by relevant numbers on the following pages Programme selector dial TEMPERATURE button SPIN button STAIN button SENSITIVE button TIME SAVING button Display DISPLAY BEM START PAUSE button 9 DELAY START button Indicator pilot lights Symbols ty Rinse Hold Cold a in Display Duration of selected programme 7 1 Duration of selected programme After selecting a programme the duration is displayed in hours and minutes for example 2 05 The duration is calculated automatically on the basis of the maximum recommended load for each type of fabric After the programme has started the time remaining is updated every minute Alarm codes In the event of operating problems some alarm codes can be displayed for example EPD see chapter What to do if End of programme When the programme has finished a blinking zero 7 is displayed the DOOR pilot light 10 2 the FUNCTIONING pilot light 10 1 and the pilot light of button 8 go out and the door can be opened Incorrect option selection If an option which is not compatible with the set wash programme is selected the message Err is displayed for about 2 seconds and the yellow pilot l
3. EXTRA RINSE This appliance is designed for saving water However for people with a very delicate skin allergic to detergents it may be necessary to rinse the laundry using an extra quantity of water Press simultaneously buttons 2 and 3 for some seconds the pilot light 10 3 comes on This function stays permanently on To remove it press the same buttons again until the pilot light 10 3 goes off Daily use Altering an option or a running programme It is possible to change any option before the programme carries it out Before you make any change you must pause the washing machine by pressing the button 8 Changing a running programme 15 possible only by resetting it Turn the programme selector dial to O and then to the new programme position Start the new programme by pressing the 8 button again The washing water in the tub will not emptied out Interrupting a programme Press the button 8 to interrupt a programme which is running the corresponding light starts blinking Press the button again to restart the programme Cancelling a programme Turn the selector dial to O to cancel a programme which is running Now you can select a new programme Opening the door after the programme has started First set the machine to pause by pressing the button 8 If the pilot light 10 2 goes off after some minutes the door can be opened If the door remains locked the pilot light 10 2 is on this means that the machine is alr
4. Special programme for jeans denim items The Extra Rinse option will be activated automatically SYNTHETICS SPIN RINSE HOLD Wy 60 Cold STAIN SENSITIVE Main wash Rinses Short spin TIME SAVING 2 EX amp Max load 3 kg Reduced load 1 5 kg TRA RINSE Synthetic or mixed fabrics underwear coloured garments non shrink shirts blouses SYNTHETICS WITH PREWASH SPIN RINSE HOLD uy 3 60 Cold STAIN SENSITIVE Wy Prewash Main wash Rinses Short spin TIME SAVING EX Ep Max load 3 kg Red load 1 5 kg TRA RINSE Synthetic or mixed fabrics with prewash phase heavily soiled items underwear coloured garments non shrink shirts blouses EASY IRON SPIN RINSE HOLD W 60 Cold EXTRA RINSE amp Main wash Rinses Short spin Max load 1 kg Synthetic fabrics to be gentle washed and spun Selecting this programme the laundry is gently wash ed and spun to avoid any creasing In this way ironing is easier Furthermore the machine will perform ad ditional rinses Washing programmes Programme Maximum and Minimum Temperature Detergent Compartment Cycle Description Options Maximum Fabrics Load Type of Laundry DELICATES SPIN RINSE HOLD Wy 40 Cold STAIN TIME SAV i Main wash Rinses Short spin ING 2 EXTRA RINSE amp Max load 3 kg Reduced load 1 5 kg Delicate fabrics acrylics viscose polyester WOOL PLUS HANDWASH yy SILK SPIN RINSE HOLD 40 Cold Main wash Rins
5. This appliance is designed for domestic use It must not be used for purposes other than those for which it was designed Only wash fabrics which are designed to be machine washed Follow the instructions on each garment label e Do not overload the appliance See the Washing Programme Table e Before washing ensure that all pockets are empty and buttons and zips are fastened Avoid washing frayed or torn articles and treat stains such as paint ink rust and grass before washing Underwired bras must NOT be machine washed Garments which have been in contact with volatile petroleum products should not be machine washed If volatile cleaning fluids are used care should be taken to ensure that the fluid is removed from the garment before placing in the machine Never pull the power supply cable to remove the plug from the socket always take hold of the plug itself Never use the appliance if the power supply cable the control panel the working surface or the base are damaged so that the inside of the washing machine is accessible Child Safety This appliance is not intended for use by person including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety The packaging components e g plastic film polystyrene can be dangerous to children danger of suffocation
6. load required also taking into account any other appliances in use A WARNING Connect the machine to an earthed socket WARNING The manufacturer does not accept any responsibility for damage or inju failure to comply with the above safety precaution A WARNING ry through The power supply cable must be easily accessible after installing the machine Environment concerns WARNING Should the appliance power supply cable need to be replaced this must be carried out by a Service Centre Environment concerns The symbol R onthe product or on its packaging indicates that this product may not be treated as household waste Instead it should be taken to the appropriate collection point for the recycling of electrical and electronic equipment By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product For more detailed information about recycling of this product please contact your local council your household waste disposal service or the shop where you purchased the product Packaging materials The materials marked with the symbol lt are recyclable gt PE lt polyethylene gt PS lt polystyrene gt PP lt polypropylene This means that they can be recycled by disposing of them properly in appropriate collection containers Ecological hints To save wa
7. or similar materials under the machine to compensate for any unevenness in the floor Water inlet An inlet hose is supplied and can be found inside the machine drum This appliance must be connected to a cold water supply Do not use the hose from your previous machine to connect to the water supply 1 Open the porthole and extract the inlet A hose 2 Connect the hose with the angled con nection to the machine Do not place the inlet hose downwards Angle the hose to the left or right de pending on the position of your water tap Installation 3 Set the hose correctly by loosening the ring nut After positioning the inlet hose be sure to tighten the ring nut again to prevent leaks 4 Connect the hose to a tap with a 3 4 thread Always use the hose supplied with the appliance The inlet hose must not be lengthened If it is too short and you do not wish to move the tap you will have to purchase a new longer hose specially designed for this type of use Installation should comply with local water authority and building regulations require ments Check the minimum water pressure required for safe operation of the appliance in the chapter Technical Data Water stop device The inlet hose is provided with a water stop device which protects against damage caused by water leaks in the hose which could develop due to nat ural ageing of the hose This fault is
8. shown by a red sector in the window A Should this occur turn the water tap off and refer to your Service Centre to replace the hose Water drainage The end of the drain hose can be positioned in three ways 1 Hooked over the edge of a sink using the plastic hose guide supplied with the machine In this case make sure the end cannot come unhooked when the machine is emptying Electrical connection This could be done by tying it to the tap witha piece of string or attaching it to the wall 2 Ina sink drain pipe branch This branch must be above the trap so that the bend is at least 60 cm above the ground 3 Directly into a drain pipe at a height of not less than 60 cm and not more than 90 cm The end of the drain hose must always be ventilated i e the inside diameter of the drain pipe must be larger than the outside diameter of the drain hose The drain hose must not be kinked Fig onion 60 AN The drain hose may be extended to a maximum of 4 metres An additional dra Joining piece is available from your local Service Centre Electrical connection Information on the electrical connection is given on the rating plate on the in the appliance door in hose and ner edge of Check that your domestic electrical installation can take the maximum
9. Keep them out of children s reach Keep all detergents in a safe place out of children s reach Product description e Make sure that children or pets do not climb a into the drum To prevent children or pets becoming trapped inside the drum the ma chine incorporates a special feature To ac tivate this device rotate the button without pressing it inside the door clockwise until the groove is horizontal If necessary use a coin To disable this device and restore the possibility of closing the door rotate the o button anticlockwise until the groove is ver tical Product description Your new appliance meets all modern requirements for effective treatment of laundry with low water energy and detergent consumption The ECO VALVE system allows total use of detergent and reduces water consumption so saving energy a ia Detergent dispenser drawer Control panel Door opening handle Rating plate BS Control panel Drain pump Fl Adjustable feet Detergent dispenser drawer uy Compartment for detergent used for pre wash The prewash detergent is added at the be ginning of the wash programme Compartment for powder or liquid detergent used for main wash Compartment for liquid additives fabric soft ener starch Compartment for stain remover used for main
10. LAVAMAT 60840 L 62840 L User manual Washing Machine Contents Thank you for choosing one of our high quality products To ensure optimal and regular performance of your appliance please read this instruction manual carefully It will enable you to navigate all processes perfectly and most efficiently To refer to this manual any time you need to we recommend you to keep it in a safe place And please pass it to any future owner of the appliance We wish you much joy with your new appliance Contents Operating instructions 3 Cancelling a programme 13 Safety information 3 Opening the door after the programme has started 13 er ee At the end of the programme 13 Use 4 Helpful hints and tips 14 Child Safety 4 Sorting out the laundry 14 Product description 5 Before loading the laundry 14 Removing stains 14 Detergent dispenser drawer 6 Detergents and additives 14 Control panel 6 Quantity of detergent to be used 15 Display 7 Degrees of water hardness 15 Indicator pilot lights 10 g Washing programmes 15 Personalization g Care and cleaning 18 Acoustic signals 8 Descaling 18 Child safety lock 8 After each wash 18 Daily use 9 aintenance wash 18 he laundry 9 External cleaning 19 o out the detergent and the fabric S drawer D 20 Select the required programme by means of Sean 20 programme selector dial 1 10 Cleanin f g the water inlet filters 21 Sele
11. TY LOCK has been activated e Deactivated this device The water tap is closed Eid e Open the water tap The inlet hose is squashed or kinked Eig Check the inlet hose connection The filter in the inlet hose is blocked Eig e Clean the water inlet hose filter The door is not properly closed E40 e Close firmly the door The end of the drain hose is too low e Refer to relevant paragraph in Water drain age section The drain hose is squashed or kinked E20 e Check the drain hose connection The drain filter is clogged EU e Clean the drain filter An option or a programme that ends with the water still in the tub or a that eliminates all the spinning phases has been selected e Disable the option e Select the draining or the spinning pro gramme The laundry is not evenly distributed in the drum e Redistribute the laundry What to do if There is water on the floor Unsatisfactory washing results The door will not open The machine vibrates or is noisy Too much detergent or unsuitable detergent creates too much foam has been used e Reduce the detergent quantity or use anoth er one Check whether there are any leaks from one of he inlet hose fittings It is not always easy to see this as the water runs down the hose check o see if it is damp e Check the water inlet hose connection The drain hose is damaged e Change it with a new one The cap on the filter has not b
12. available washing machine detergents may be used in this appliance powder detergents for all types of fabric e powder detergents for delicate fabrics 60 C max and woollens e liquid detergents preferably for low temperature wash programmes 60 C max for all types of fabric or special for woollens only The detergent and any additives must be placed in the appropriate compartments of the dispenser drawer before starting the wash programme If using liquid detergents a programme without prewash must be selected Your appliance incorporates a recirculation system which allows an optimal use of the concentrated detergent Follow the product manufacturer s recommendations on quantities to use and do not exceed the MAX mark in the detergent dispenser drawer Quantity of detergent to be used The type and quantity of detergent will depend on the type of fabric load size degree of soiling and hardness of the water used Follow the product manufacturers instructions on quantities to use Use less detergent if you are washing a small load e the laundry is lightly soiled e large amounts of foam form during washing Degrees of water hardness Water hardness is classified in so called degrees of hardness Information on hardness of the water in your area can be obtained from the relevant water supply company or from your local authority If the water hardness degree is medium or high we suggest you to add a water soft
13. can be solved easily without calling out an engineer Before contacting your local Service Centre please carry out the checks listed below During machine operation it is possible that the yellow pilot light of button 8 blinks one of the following alarm codes appears on the display and at the same time some acoustic signals sound every 20 seconds to indicate that the machine is not working e 10 problem with the water supply e EP problem with the water draining e E40 door open e EFET anti flooding system has activated Once the problem has been eliminated press the button 8 to restart the programme If after all checks the problem persists contact your local Service Centre What to do if The washing machine does not start The machine does not fill The machine fills then empties immediately The machine does not empty and or does not spin The door has not been closed EY fF e Close firmly the door The plug is not properly inserted in the power socket e Insert the plug into the power socket There is no power at the socket e Please check your domestic electrical instal lation The main fuse has blown e Replace the fuse The selector dial is not correctly positioned and the button 8 has not been depressed e Please turn the selector dial and press the button 8 again The delay start has been selected e If the laundry is to be washed immediately cancel the delay start The CHILD SAFE
14. ct the desired TEMPERATURE Button Emergency emptying out 22 Frost ti 23 Select the SPIN speed or the RINSEHOLD yy kenn Na option Button 3 11 at to do if 23 Programme option buttons 11 Technical data 26 Select the STAIN option Button 4 11 Consumption values 27 SENSITIVE option Button 5 11 eae Select the TIME SAVING option Button 6 Installation instructions 27 11 Installation 27 Select the START PAUSE Button 8 12 Unpacking 7 Select the DELAY START Button 9 12 Positioning and levelling 30 Select an additional rinse EXTRA RINSE Water inlet 30 12 Water stop device 31 Altering an option or a running programme Water drainage 31 3 Electrical connection 32 Interrupting a programme 13 132951560 00 282009 Safety information Environment concerns 33 Ecological hints 33 Packaging materials 33 Subject to change without notice Operating instructions A Safety information A Read carefully amp keep for future reference The safety of Your appliance complies with the industry standards and with legal re quirements on the safety of appliances However as manufacturers we feel it is our duty to provide the following safety notes It is most important that this instruction book should be retained with the appliance for future reference Should the appliance be sold or transferred to another owner or should you move house and leave the appliance always ensure that the book is supplied with the appliance in or
15. d the fabric softener Your new appliance was designed to reduce water energy and detergent consumption 1 Pull out the dispenser drawer until it stops Measure out the amount of deter gent required pour it into the main wash compartment wiy and if you wish to carry out the prewash phase pour the deter gent into the compartment marked uy If you wish to perform the stain function pour the stain remover into the compart ment marked with blue arrow BED Daily use 2 If required pour fabric softener into the compartment marked the amount used must not exceed the MAX mark in the drawer Close the drawer gently Select the required programme by means of programme selector dial 1 i You can choose the right programme for any type of laundry following the descriptions on the washing programme tables see Washing Programmes Turn the programme selector dial to the required programme The programme selector determines the type of washing cycle e g water level drum movement number of rinses and the washing temperature according to the type of laundry The pilot light of button 8 starts blinking The selector dial can be turned either clockwise or anticlockwise Position O to Reset programme Switching OFF of the machine At the end of the programme the selector dial must be turned to position O to switch the machine off If you turn the programme
16. der that the new owner can get to know the functioning of the appliance and the relevant warnings e You MUST read them carefully before installing or using the appliance e Before first starting up check the appliance for any damage incurred during transport Never connect up a damaged appliance If parts are damaged contact your supplier If the appliance is delivered in the winter months when there are minus temperatures Store it at room temperature for 24 hours before using for the first time General safety It is dangerous to alter the specifications or attempt to modify this product in any way During high temperature wash programmes the door glass may get hot Do not touch it Make sure that small pets do not climb into the drum To avoid this please check into the drum before using Any objects such as coins safety pins nails screws stones or any other hard sharp material can cause extensive damage and must not be placed into the machine Only use the advised quantities of fabric softener and detergent Damage to the fabric can ensue if you over fill Refer to the manufacturer s recommendations of quantities Wash small items such as socks laces washable belts etc in a washing bag or pillow case as it is possible for such items to slip down between the tub and the inner drum Do not use your washing machine to wash articles with whalebones material without hems or torn material Always unplug the appliance and turn off th
17. ding on the programme selected there can be hot water in the pump Never remove the pump cover during a wash cycle always wait until the appliance has finished the cycle and is empty When replacing the cover ensure it is securely retightened so as to stop leaks and young children being able to remove it Cleaning the water inlet filters aX If the appliance doesn t fill takes long to fill water the starting button blinks yellow or the display if available shows the relevant alarm see chapter What to do if for more details check if the water inlet filters are blocked To clean the water inlet filters Care and cleaning 1 Turn off the water tap Unscrew the hose from the tap 3 Clean the filter in the hose with a stiff brush 4 Screw the hose back onto the tap Make sure the connection is tight N 5 Unscrew the hose from the machine Keep a rug nearby because some water may flow 6 Clean the filter in the valve with a stiff brush or with the piece of cloth 7 Screw the hose back to the machine and make sure the connection is tight 8 Turn on the water tap Emergency emptying out If the water is not discharged proceed as follows to empty out the machine 1 pull out the plug from the power socket 2 close the water tap 3 if necessary wait until the water has cooled down 4 open the pump door 5 place a bowl on the floor and place the end of the emergency empt
18. door open to prevent the formation of mildew and unpleasant smells Helpful hints and tips Helpful hints and tips Sorting out the laundry Follow the wash code symbols on each garment label and the manufacturer s washing instructions Sort the laundry as follows whites coloureds synthetics delicates woollens Before loading the laundry Never wash whites and coloureds together Whites may lose their whiteness in the wash New coloured items may run in the first wash they should therefore be washed separately the first time Button up pillowcases close zip fasteners hooks and poppers Tie any belts or long tapes Remove persistent stains before washing Rub particularly soiled areas with a special detergent or detergent paste Treat curtains with special care Remove hooks or tie them up in a bag or net Removing stains Stubborn stains may not be removed by just water and detergent It is therefore advisable to treat them prior to washing Blood treat fresh stains with cold water For dried stains soak overnight in water with a special detergent then rub in the soap and water Oil based paint moisten with benzine stain remover lay the garment on a soft cloth and dab the stain treat several times Dried grease stains moisten with turpentine lay the garment on a soft surface and dab the stain with the fingertips and a cotton cloth Rust oxalic acid dissolved in hot water or a rust removing product used cold
19. e Description Options Maximum Fabrics Load Type of Laundry ECONOMY SPIN RINSE HOLD 60 STAIN SENSITIVE EX Main wash Rinses Long spin TRA RINSE Max load 6 kg White and fast coloured cotton This programme can be selected for slightly or nor mally soiled cotton items The temperature will de crease and the washing time will be extended This allows to obtain a good washing efficiency so saving energy O For cancelling the programme which is running or to switch the machine off PE 1 STAIN option can be selected only at the temperature of 40 C or higher 2 If you select the SUPER QUICK option by pressing button 6 we recommend that you reduce the maximum load as indicated Full loading is possible however with somewhat reduced cleaning results 3 If using liquid detergents a programme without PREWASH must be selected Care and cleaning You must DISCONNECT the appliance from the electricity supply before you can carry out any cleaning or maintenance work Descaling The water we use normally contains lime It is a good idea to periodically use a water softening powder in the machine Do this separately from any laundry washing and ac cording to the softening powder manufacturer s instructions This will help to prevent the formation of lime deposits After each wash Leave the door open for a while This helps to prevent mould and stagnant smells forming inside the appliance Keeping the d
20. e chapter Se lect an additional rinse Personalization Acoustic signals Child safety lock The machine is provided with an acoustic device which sounds in the following cases e at the end of the cycle e in the event of operating problems By pressing the 3 and 4 buttons simultaneously for about 6 seconds the acoustic signal is deactivated except for the events of operating problems By pressing these 2 buttons again the acoustic signal is reactivated This device permits you to leave the appliance unsupervised and not to worry that children might be injured by or cause damage to the appliance This function remains able also when the washing machine is not working There are two different ways to set this option e Before pressing button 8 it will be impossible to start the machine e after pressing button 8 it will be impossible to change any other programme or option To enable or disable this option press simultaneously for about 6 seconds buttons 4 and 5 until the symbol 7 3 appears or disappears on or from the display Daily use Daily use Load the laundry 1 Open the door by carefully pulling the door handle outwards Place the laundry in the drum one item at a time shaking them out as much as possible 2 Close firmly the door You must hear a click during closing WARNING Do not embed the laundry between the door and the rubber joint Measure out the detergent an
21. e water supply after use cleaning and maintenance Under no circumstances should you attempt to repair the machine yourself Repairs carried out by inexperienced people may cause injury or serious malfunctioning Contact your local Service Centre Always insist on genuine spare parts Safety information Installation Use This appliance is heavy Care should be taken when moving it When unpacking the appliance check that it is not damaged If in doubt do not use it and contact the Service Centre All packing and transit bolts must be removed before use Serious damage can occur to the product and to property if this is not adhered to See relevant section in the user manual After having installed the appliance check that it is not standing on the inlet and drain hose and the worktop is not pressing the electrical supply cable against the wall If the machine is situated on a carpeted floor please adjust the feet in order to allow air to circulate freely under the appliance Always be sure that there is no water leakage from hoses and their connections after the installation If the appliance is installed in a location subject to frost please read the dangers of freezing chapter Any plumbing work required to install this appliance should be carried out by a qualified plumber or competent person Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person
22. eady heating that the water level is above the bottom edge of the door In this case the door can not be opened If you cannot open the door but you need to open it you have to switch the machine off by turning the selector dial to O After some minutes the door can be opened pay attention to the water level and temperature After closing the door it is necessary to select the programme and options again and to press button 8 At the end of the programme The machine stops automatically the pilot light of button 8 the pilot lights 10 1 and 10 2 go off and a blinking will appear on the display If a programme or an option that ends with water still in the tub has been selected the pilot light 10 2 illuminates a blinking will appear on the display the pilot light of button 8 goes off and the door remains locked to indicate that the water must be emptied out before opening the door Follow the below instructions to empty out the water e Turn the programme selector dial to O Select the DRAIN or SPIN programme Reduce the spin speed if needed by means of the relevant button Press button 8 When the programme has finished the display shows a blinking 7 The pilot light 10 2 goes off and the door can be opened Turn the programme selector dial to to switch the machine off Remove the laundry from the drum and carefully check that the drum is empty If you do not intend to carry out another wash close the water tap Leave the
23. ears and normal spinning can resume If after some minutes the laundry is still not evenly distributed in the drum the machine will not spin e Redistribute the laundry The machine is fitted with a type of motor which makes an unusual noise compared with other traditional motors This new motor ensures a softer start and more even distribution of the laundry in the drum when spinning as well as increased stability of the machine The machine makes an unusual noise Machines based on modern technology operate No water is visible in the drum very economically using very little water with out affecting performance Anti flooding system has activated The display shows the alarm code EFD e Disconnect the appliance and contact the Service Force Centre If you are unable to identify or solve the problem contact our service centre Before telephoning make a note of the model serial number and pur chase date of your machine the Service Centre will require this information Mod Prod No n n Ser No Technical data Dimensions Width 60 cm Height 85 cm Depth 63 cm Electrical connection Information on the electrical connection is given on the rating plate on the inner edge of the appliance door Water supply pressure Minimum 0 05 MPa Maximum 0 8 MPa Consumption values Maximum Load Cotton 6 kg Spin Speed Maximum 1000 rpm L 60840 L 1200 rpm L 62840 L Consump
24. een replaced or he filter has not been properly screwed in after cleaning action e Put the cap back on the filter or screw the filter fully in Too little detergent or unsuitable detergent has been used e Increase the detergent quantity or use an other one Stubborn stains have not been treated prior to washing e Use commercial products to treat the stub born stains The correct temperature was not selected e Check if you have selected the correct tem perature Excessive laundry load e Introduce into the drum less laundry The programme is still running e Wait the end of washing cycle The door lock has not been released e Wait until the pilot light DOOR has gone off There is water in the drum e Select drain or spin programme to empty out the water The transit bolts and packing have not been re moved e Check the correct installation of the appli ance The support feet have not been adjusted e Check the correct levelling of the appliance The laundry is not evenly distributed in the drum e Redistribute the laundry Maybe there is very little laundry in the drum e Load more laundry Technical data The electronic unbalance detection device has cut in because the laundry is not evenly distrib uted in the drum The laundry is redistributed by reverse rotation of the drum This may hap Spinning starts late or the machine does not pen several times before the unbalance disap spin p
25. ener following always the manufacturer s instructions When the degree of hardness is soft readjust the quantity of the detergent Washing programmes Programme Maximum and Minimum Temperature Detergent Cycle Description Options Compartment Maximum Fabrics Load Type of Laundry COTTONS LINEN SPIN RINSE HOLD wy 95 Cold STAIN SENSITIVE ey Main wash Rinses Long spin TIME SAVING 2 EX amp Max load 6 kg Reduced load 3 kg TRA RINSE For white and coloured cotton normally soiled items EET Washing programmes Programme Maximum and Minimum Temperature Detergent Compartment Cycle Description Options Maximum Fabrics Load Type of Laundry COTTONS WITH PREWASH SPIN RINSE HOLD uy 95 Cold STAIN SENSITIVE wy Prewash Main wash Rinses Long spin TIME SAVING 2 EX Max load 6 kg Reduced load 3 kg TRA RINSE For white or coloured cottons with prewash phase heavily soiled items 40 60 MIX SPIN RINSE HOLD wy 40 STAIN SENSITIVE EX n Main wash Rinses Long spin TRA RINSE amp Max load 6 kg White and coloured cotton This programme can be used for laundry which should be washed at 40 C or 60 C separately The maximum load capacity can be put into the drum in order to save energy and water The same good washing result will be obtained as for normal programme at 60 C JEANS SPIN RINSE HOLD wy 60 Cold amp Main wash Rinses Long spin Max load 3 kg
26. es Short spin Wool Handwash Max load 2 kg Silk Max load 1 kg Washing programme for machine washable wool as well as for hand washable woollens and delicate fab rics Note A single or bulky item may cause imbal ance If the appliance doesn t perform the final spin phase add more items redistribute the load manually and then select the spinning programme E DELICATE RINSES SPIN RINSE HOLD amp Rinses Short spin EXTRA RINSE Max load 6 kg With this programme it is possible to rinse and spin cotton garments which have been washed by hand The machine performs some rinses followed by a final spin The spin speed can be reduced by pressing the relevant button DRAIN Draining of water For emptying out the water of the last rinse in pro grammes with the RINSE HOLD option selected SPIN SPIN Drain and long spin Max load 6 kg Separate spin for hand washed cotton garments and after programmes with the RINSE HOLD option se ected Before selecting this programme the selector dial must be turned to O You can choose the spin speed by pressing the relevant button to adapt it to he fabrics to be spun FRESH UP SPIN wy 30 amp Main wash Rinses Short spin Max load 3 kg his programme may be used for quick wash for sport items or cotton and synthetic items lightly soiled or worn once WEE Care and cleaning Programme Maximum and Minimum Temperature Detergent Compartment Cycl
27. ight of button 8 light starts blinking Delay Start 7 2 The selected delay 20 hours max set by means of the relevant button appears on the display for about 3 seconds then the duration of the previously selected programme is displayed The symbol 7 2 will appear on the display The delay time value decreases by one unit every hour When only 1 hour remains the time decreases every minute Child safety lock 7 3 Indicator pilot lights 10 i Stand by mode If your laundry is not removed during 10 minutes after the programme is finished the backlight of the display switches off and the energy saving system will be enabled Only the button 8 pilot light is blinking to indicate that the appliance has to be switched off By pressing any buttons the appliance will come out from the energy saving status and you could set another washing programme or switch off the appliance Indicator pilot lights 10 After having pressed the button 8 the WASHING pilot light 10 1 comes on When the pilot light 10 1 comes on this means 0 that the machine is operating CO e The DOOR pilot light 10 2 indicates if the door can be opened e light on the door cannot be opened 0 2 e light blinking the door is opening e light off the door can be opened When the appliance is performing additional rin ses the EXTRA RINSE pilot light 10 3 comeson L___ 0 3 To add an additional rinse please se
28. lide out the relevant plastic spacers Open the porthole take out the inlet hose from the drum and remove the polystyr ene block fitted on the door seal Fill the smaller upper hole and the two large ones with the corresponding plastic plug caps supplied in the bag containing the instruction booklet Connect the water inlet hose as described under the paragraph Water inlet Installation Positioning and levelling Install the machine on a flat hard floor Make sure that air circulation around the machine is not impeded by carpets rugs etc Before placing it on small tiles apply a rubber coating Never try to correct any unevenness in the floor by putting pieces of wood cardboard or similar materials under the machine If it is impossible to avoid positioning the machine next to a gas cooker or coalburning stove an in sulating panel covered with aluminium foil on the side facing the cooker or stove must be inserted between the two appliances The machine must not be installed in rooms where the temperature can drop below 0 C The water inlet hose and the drain hose must not be kinked Please ensure that when the appliance is installed it is easily accessible for the engineer in the event of a breakdown Carefully level by screwing the adjustable feet in or out Never place cardboard wood
29. ogether with EXTRA RINSE option This option is recommended for non fast coloured items and for frequently washed items Select the TIME SAVING option Button 6 This option allows you to modify the washing time automatically proposed by the appli ance DAILY by pressing button 6 once the relative pilot light comes on and the washing duration will be reduced to wash daily soiled laundry SUPER QUICK by pressing button 6 twice the relative pilot light remains lit the washing duration will be reduced to wash lightly soiled laundry or items that have been used or worn for a short time On the display will be visualized the decreased washing time Daily use Select the START PAUSE Button 8 To start the selected programme press the button 8 the corresponding red pilot light stops blinking The pilot light 10 1 is on to indicate that the appliance starts operating The pilot light 10 2 is on to indicate the door is locked To interrupt a programme which is running press the button 8 the corresponding red pilot light starts blinking To restart the programme from the point at which it was interrupted press the button 8 again If you have chosen a delayed start with button 9 the machine will begin the count down If an incorrect option is selected the yellow pilot light of the button 8 blinks for 3 times the message Err is displayed for about 2 seconds Select the DELAY START Button 9 A Before you start the
30. ol 1 2 Remove any rust deposits on the drum with a cleaning agent for stainless steel Run a washing cycle without any washing to clean off any cleaning agent residues Programme Short Cotton Programme at maximum temperature and add approx 1 4 measuring cup of detergent Care and cleaning Door seal Check from time to time the door seal and elimi nate eventual possible objects that could be trap ped in the fold Drain pump The pump should be inspected regularly and particularly if the machine does not empty and or spin e the machine makes an unusual noise during draining due to objects such as safety pins coins etc blocking the pump Proceed as follows 1 Disconnect the appliance 2 If necessary wait until the water has cooled down 3 Open the pump door 1 L 4 Place a container close to the pump to collect any spillage 5 Release the emergency emptying hose place it in the container and remove its cap cover Care and cleaning 6 When no more water comes out un screw the pump and remove it Always keep a rag nearby to dry up spillage of water when removing the pump 8 Putthe cap back on the emergency emp tying hose and place the latter back in its seat 9 Screw the pump fully in 10 Close the pump door WARNING When the appliance is in use and depen
31. oor open after a wash will also help to preserve the door seal Maintenance wash With the use of low temperature washes it is possible to get a build up of residues inside the drum We recommend that a maintenance wash be performed on a regular basis To run a maintenance wash e The drum should be empty of laundry e Select the hottest cotton wash programme e Use a normal measure of detergent must be a powder with biological properties Care and cleaning External cleaning Clean the exterior cabinet of the appliance with soap and water only and then dry thor oughly A Do not use methylated spirits solvents or similar products to clean the cabinet Detergent dispenser drawer The detergent dispenser drawer should be cleaned regularly 1 2 Remove the detergent dispenser drawer by pulling it firmly Remove the conditioner insert from the middle compartment Clean all parts with water Put the conditioner insert in as far as it will go so that it is firmly in place Clean all parts of the washing machine especially the nozzles in the top of the washing in chamber with a brush Insert the detergent dispenser drawer in the guide rails and push it in Washing drum Rust deposits in the drum may occur due to rusting foreign bodies in the washing or tap water containing iron ds Do not clean the drum with acidic descaling agents scouring agents containing chlorine or iron or steel wo
32. ot light 10 2 goes on the pilot light of button 8 is off and the door is blocked to indicate that the water must be emptied out To empty the water out please read chapter At the end of the programme Programme option buttons i Depending on the programme different functions can be combined These must be selected after choosing the desired programme and before pressing the button 8 When these buttons are pressed the corresponding pilot lights come on When they are pressed again the pilot lights go out If an incorrect option is selected the in yellow pilot light of the button 8 blinks for 3 times and the Err message appears on the display for some seconds For the compatibility among the washing programmes and the options see chapter Wash ing Programmes Select the STAIN option Button 4 Select this option to treat heavily soiled or stained laundry with stain remover extended main wash with time optimized stain action phase The relevant light will light up This option is not available with a temperature lower than 40 C If you wish to perform a programme with the stain option pour stain remover into stain compartment marked with a blue arrow SENSITIVE option Button 5 By selecting this option the washing intensity will be reduced The machine adds one rinse in the programmes for COTTONS 40 60 MIX SYNTHETICS and ECONOMY The relevant symbol will appear on the display This option cannot be selected t
33. programme if you wish to delay the start press the button re peatedly to select the desired delay The selected delay time value up to 20 hours will appear on the display for about 3 seconds then the duration of the programme will appear again You must select this option after you have set the programme and before you press the button 8 The wash programme can be delayed from 30 min 60 min 90 min 2 hours and then by 1 hour up to a maximum of 20 hours by means of this button If you wish to add laundry in the machine during the delay time you will press button 8 to put the machine in pause Add the laundry close the door and press button 8 again Selecting the delayed start e Select the programme and the required options e Select the delay start e Press button 8 the appliance starts its hourly countdown The programme will start after the selected delay has expired eng the delayed start e Set the washing machine to PAUSE by pressing the button 8 e Press button 9 once until the symbol 7 is displayed e Press the button 8 again to start the programme The selected delay can be changed only after selecting the washing programme again The door will be locked throughout the delay time If you need to open the door you must first set the washing machine to PAUSE by pressing the button 8 After you have closed the door press the button 8 again The button 9 can not be selected with DRAIN programme Select an additional rinse
34. selector dial to another programme when the machine is work ing the yellow pilot light of button 8 will blink 3 times and the message Err is displayed on the display to indicate a wrong selection The machine will not perform the new selected programme Select the desired TEMPERATURE Button 2 i i When selecting a programme the appliance automatically proposes the default tempera ture provided for that programme Press this button repeatedly to increase or decrease the temperature if you want your laundry to be washed at a temperature different from the one proposed by the washing machine By selecting position Cold the machine will wash with cold water To be used for extremely delicate items such as curtains For the maximum and the minimum available wash water temperature see Washing pro grammes Daily use 6 Select the SPIN speed or the RINSE HOLD option Button 3 i When the required programme has been selected your appliance automatically proposes the maximum spin speed provided for that programme Press this button repeatedly to change the spin speed if you want your laundry to be spun at a speed different from the one proposed by the washing machine The relevant light will light up RINSE HOLD by selecting this option the water of the last rinse is not emptied out to prevent the fabrics from creasing When the programme has finished the display shows a blinking 7 the pil
35. ter energy and to help protect the environment we recommend that you follow these tips e Normally soiled laundry may be washed without prewashing in order to save detergent water and time the environment is protected too e The machine works more economically if it is fully loaded With adequate pre treatment stains and limited soiling can be removed the laundry can then be washed at a lower temperature Measure out detergent according to the water hardness the degree of soiling and the quantity of laundry being washed lt www electrolux com 600282 00 0951S62EL
36. tion values Programme Energy consumption Water consumption Programme duration KWh litres Minutes 61 White Cottons 95 Cottons 60 11 3 58 For the duration of 1 1 02 45 Cotton ECO 60 the programmes Cottons 40 0 7 58 please refer to the 7 display on the con Synthetics 40 0 5 50 trol panel Delicates 40 0 55 60 Wool Handwash 30 0 25 58 1 Cotton Eco at 60 C with a load of 6 kg is the reference programme for the data entered in the energy label in compliance with EEC 92 75 standards i The consumption data shown on this chart is to be considered purely indicative as it may vary depending on the quantity and type of laundry on the inlet water temperature and on the ambient temperature Installation instructions Installation Unpacking All transit bolts and packing must be removed before using the appliance You are advised to keep all transit devices so that they can be refitted if the machine ever has to be transported again Installation 1 After removing all the packaging careful ly lay machine on it s back to remove the polystyrene base from the bottom 2 Remove the power supply cable and the draining hose from the hose holders on the rear of the appliance AW NNN 3 Unscrew the three bolts using the key supplied with the machine Installation 4 5 6 S
37. ying hose into the bowl Remove its cap The water should drain by gravity into the bowl When the bowl What to do if is full put the cap back on the hose Empty the bowl Repeat the procedure until water stops flowing out 6 clean the pump if necessary as previously described 7 replace the emergency emptying hose in its seat after having plugged it 8 screw the pump again and close the door Frost precautions A If the machine is installed in a place where the temperature could drop below 0 C proceed as follows 1 close the water tap and unscrew the water inlet hose from the tap 2 place the end of the emergency emptying hose and that of the inlet hose in a bowl placed on the floor and let water drain out 3 screw the water inlet hose back on and reposition the emergency emptying hose after having put the cap on again By doing this any water remaining in the machine is removed avoiding ice forming and consequently damage to the appliance When you use the machine again make sure that the ambient temperature is above 0 C Every time you drain the water through the emergency emptying hose you must pour 2 litres of water into the main wash compartment of the detergent drawer and then run the drain programme This will activate the ECO Valve device avoiding that part of the deter gent remains unused at next washing What to do if Certain problems are due to lack of simple maintenance or oversights which
Download Pdf Manuals
Related Search