Nilfisk-ALTO C 100.4 Nilfisk-ALTO C 110.2 Nilfisk
Contents
1. Type C 100 4 5 C 110 2 5 C 110 2 5 X TRA Rated pressure bar MPa 65 6 5 70 7 0 70 7 0 Permissible pressure bar MPa max 100 10 0 max 110 11 0 max 110 11 0 Rated flow min 5 3 5 0 5 2 Rated input kW 1 3 1 4 1 4 Rated voltage V 230 240 230 240 230 240 Max water temperature C 40 40 40 Inlet pressure bar MPa 0 15 10 0 015 1 0 0 15 10 0 015 1 0 0 15 10 0 015 1 0 Sound pressure level dB A 78 78 78 Guaranteed sound power level dB A 92 92 92 Vibration according to ISO 5349 m s2 max 2 5 max 2 5 max 2 5 10 Declaration C Declaration Manufacturers name and address or his authorized representative in the Community 89287 Bellenberg GERMANY Nilfisk Advance AG Nilfisk ALTO Business Unit Guido Oberdorfer Str 10 technical documentation Name of the person responsible for the Wolfgang Nieuwkamp Description of the equipment Equipment name Nilfisk ALTO High pressure washer Model C 100 4 5 C 110 2 5 C 110 2 5 X TRA Dimension 255 x 240 x 630 mm Rated output voltage AC 230 240 V Rated frequency 50 Hz Rated input power 1 3 1 4 kW Measured sound pressure level 90 dB A Guaranteed sound power level 92 dB A Declaration Machine Directive The equipment refer in this document fulfils all the require ments of the Directive 98 37 EC Low voltage Directive EN 60335 2 79 2004 EN 60335 1 A1 2004 EN 50366 2003 EMC Directive EN 55014 1 A2 2002 EN 55014 2 A1 2001 EN 61000 3 22. 03 01 2007 Nilfisk ALTO C 100 4 Nilfisk ALTO C 110 2 Nilfisk ALTO C 110 2 X TRA Nilfisk ALTO Why Compromise Index Description Maintenance Trouble shooting Further information Technical data Declaration O O O I O Q Q NN Safety precautions and warnings Before you start using your pressure washer Operating your pressure washer After using your pressure washer 1 Safety Precautions and Warnings Symbols used to mark in structions Do not let people who have not been trained in the use of a high pressure washer nor read the instruction manual operate the machine This appliance is not intended for use by children or other persons without assistance or supervision if their physical sensory or mental capabili ties prevent them from using it safely Children should be su pervised to ensure that they do not play with the appliance Before starting up your ma chine please check it carefully for any defects If you find any do not start up your machine Before starting up your high pressure washer for the first time this instruction manual must be read through carefully Save the instructions for later use Safety instructions marked with this symbol must be observed to pre vent danger to persons and contact your Nilfisk ALTO distributor Especially check The insulation of the electric cable should be faultless and without any cracks
3. therefore always hold it firmly with both hands IMPORTANT Point the nozzle at the ground 1 Check that the machine is in uprigth position NOTE Do not place the ma chine in high grass 2 Release the trigger lock 7a 3 Activate the trigger of the spray gun and let the water run until all air has escaped from the water hose 4 Press the Start stop switch 04 5 Activate the trigger of the spray gun Always adjust the distance and thus the pressure of the nozzle to the surface which is to be cleaned IMPORTANT Only use wa ter without any impurities If there is a risk of running sands in the inlet water i e from your own well an additional filter 106411231 should be mounted 1 Let the water run through the water hose before connecting it to the machine to prevent sand and dirt from penetrat ing the machine Note Check that the filter is fitted in the water inlet pipe and that it is not clogged up 2 Connect the water hose to the water supply by means of the quick connector inlet water max pressure 10 bar max temperature 40 C 3 Turn on the water Do not cover the machine during operation or use it ina room without adequate ventila tion Note If the ma chine is left or not used for 5 min utes it must be switched off on the start stop switch O 1 _ Press the start stop switch O 2 Disconnect the electrical plug from the socket Shut off the water
4. If the electric cable is damaged an authorized Nilfisk ALTO distributor should replace it WARNING High pressure jets can be dangerous Never direct the water jet at persons pets live electrical equipment or the machine itself Never try to clean clothes or footwear on yourself or other persons This symbol is used to mark safety instructions that must be ob served to prevent damage to the ma chine and its performance This symbol in dicates tips and instructions to simplify work and to ensure a safe operation Hold the spray lance firmly with both hands The spray lance is affected by a thrust of up to 26 5 Nm during ope ration The operator and anyone in the immediate vicinity of the site of cleaning should take action to protect themselves from being struck by debris dislodged during operation Wear goggles and protection clothes during operation This appliance has been de signed for use with cleaning agents supplied or recom mended by the manufacturer The use of other cleaning agents or chemicals may adversely affect the safety of the appliance Disconnect from electrical power supply before carrying out user maintenance To ensure the appliance safety only use original spare parts from the manufacturer or approved by the manufac turer High pressure hoses fittings and couplings are important for the safety of the appli ance Only use hoses fittings and co
5. of this instruction manual have been thoroughly observed that repair has not been carried out or attempted by other than Nilfisk ALTO trained service staff that only original accessories have been applied that the product has not been exposed to abuse such as knocks bumps or frost that only water without any impurities has been used As specified in European Direc tive 2002 96 EC on old electri cal and electronic appliances used electrical goods must be collected separately and recycled ecologically Contact your local authorities or your nearest dealer for further information that the high pressure washer has not been used for rental nor used commer cially in any other way Repairs under this guarantee include replacement of defec tive parts exclusive of packing and postage carriage Besides we refer to your national law of sale The machine should be for warded to one of the service centres of the Nilfisk ALTO organisation with description specification of the fault Repairs not covered by the guarantee conditions will be invoiced l e malfunctions due to Causes mentioned in section Troubleshooting Chart of the instruction manual In order that Nilfisk ALTO can render you optimum service you should register your product on our web site www nilfisk alto com under PRODUCT REGISTRATION 14 9 Main Technical Data
6. A2 2005 EN 61000 3 3 A1 2001 Outdoor Noise Directive 73 23 EEC 89 336 EEC 2000 14 EC Place and date of the declaration Bellenberg November 10 2005 Signature C 100 4 GIR C 110 2 X TRA C110 2 st
7. OANOaARWND Only use the high pressure washer for purposes described in this manual The safety precautions must be observed to prevent damage to the machine the surface to be cleaned or severe personal injuries 9 Click amp Clean Powerspeed nozzle 10 Foam sprayer 11 Nozzle cleaning tool 12 Lance and nozzle holder 13 Model tag 14 Holder for electric cable not standard on all models Specifications See model tag 13 of machine We reserve the right to alter the specifications pressure washer 3 1 Mounting of lance and nozzle holder 3 2 Mounting of holder for electric cable 3 3 Mounting of wheels only models including wheels 3 Before you start using your 1 Press the lance and nozzle holder 12 on to the ma chine 1 Press the holder for electric cable 14 on to the machine The holder is not standard on all models 1 Mount the wheel bracket by pressing it into the guide at the bottom of the ma chine and mounting the two screws 2 Mount the wheels by press ing them into the bracket 3 4 Mounting of trolley handle models with trol ley handle 3 5 Mounting of quick coupling 3 6 Mounting of high pres sure hose on spray gun ZZ 4 gt 1 Place the trolley handle on the machine 2 Secure the handle by mount ing the 2 screws 1 Screw
8. e electrical plug from the socket prior to maintenance or cleaning To ensure a long and problem free working life please take the following advice Wash out water hose high pressure hose spray lance and accessories before mounting 6 1 Cleaning of water inlet filter 6 2 Cleaning of nozzle Clean the connectors of dust and sand Rinse the detergent spraying attachment after use e Clean the nozzles Any repair should always be made in an authorized workshop with original spare parts Clean the water inlet filter regularly once a month or more frequently according to use Carefully loosen the filter with a screwdriver and clean it Check that it is intact before re mount ing it The inlet filter must always be fitted inside the water inlet pipe to filter out sand limestone and other impurities as they will damage the pump valves CAUTION Failure to fit the filter will invalidate the guarantee A clogging up in the nozzle causes a pump pressure which is too high This is why cleaning is required immediately 1 Stop the machine and dis connect the nozzle 2 Clean the nozzle IMPOR TANT The cleaning tool 11 should only be used when the nozzle is detached 3 Flush the nozzle backwards with water 6 3 Cleaning of machine vents 6 4 Greasing of couplings The machine should be kept clean so as to let cooling air pass freely through the ma chine
9. nclude either a residual current device that will interrupt the supply if the leakage current to earth ex ceeds 30 mA for 30 ms Water connection Connection to the public mains according to regula tions Inlet hose can be connected to the water mains with a max inlet pressure of 10 bars IMPORTANT Only use wa ter without any impurities If there is a risk of running sands in the inlet water i e from your own well an additional filter should be mounted Safety devices The unloader valve can re duce pressure if it exceeds pre set values Locking device on spray gun 7a see foldout at the end of this manual The spray gun features a lock ing device When the pawl is activated the spray gun cannot be operated Thermal sensor A thermal sensor protects the motor against overloading The machine will restart after a few minutes when the thermal sen sor has cooled 2 Description 2 1 Application 2 2 Operation elements and model survey Ie This high pressure washer has been developed for domestic use within Car motorbike boat cara van trailer patio drive flags tones woodwork brickwork barbecue garden furniture lawn mower See foldout at the end of this manual Start stop switch Water inlet with filter 2a High pressure connection High pressure hose Electric cable Click amp Clean spray lance Spray gun with lock 7a Click amp Clean Tornado nozzle
10. ntil regular working pressure resumes Check that the water supply corresponds to specifications required see model tag NB Avoid using long thin hoses min 1 2 Clean the nozzle see section 6 2 Clean the filter see section 6 1 Straighten out hose Machine often starts and stops by itself Pump spray gun is leaking Contact your nearest Nilfisk ALTO Service Centre Machine starts but no water comes out Pump hoses or accessory frozen No water supply Water filter blocked Nozzle blocked Wait for pump hoses or accessory to thaw Connect inlet water Clean the filter see section 6 1 Clean the nozzle see section 6 2 In case problems other than the above occur please contact your local Nilfisk ALTO distributor 8 1 Recycling the washer a Sai 8 2 Warranty conditions 8 Further information Make the old cleaner unusable immediately 1 Unplug the cleaner and cut the electric cable Do not discard electrical appli ances with household waste Nilfisk ALTO guarantees high pressure washers for domestic use for 2 years If your high pressure washer or accessories are handed in for repair a copy of the receipt must be enclosed Guarantee repairs are being made on the following condi tions e that defects are attributable to flaws or defects in materi als or workmanship wear and tear as well as misuse are not covered by the guarantee e that the directions
11. supply and activate the trigger to relieve the machine of pressure 4 Lock the spray gun 7a When releasing the trigger of the spray gun the machine automatically stops The ma chine will start again when you re activate the spray gun 5 1 Storing the washer 5 2 Winding up of electric cable and high pressure hose 5 3 Storage of accessories The machine should be sto red in a frost free room Pump hose and accessories should always be emptied of water prior to storing as follows 1 Stop the machine press the start stop switch O 1 and detach water hose and ac cessory 2 Restart the machine and activate the trigger Let the machine run until no more water runs through the spray gun 5 After using your pressure washer 3 Stop the machine unplug and wind up hose and cable 4 Place spray handle nozzles and other accessories in the holders of the machine Should the machine by mistake be frozen it will be necessary to check it for damage NEVER START UP A FROZEN MACHINE Frost damages are not covered by the guarantee To avoid accidents the electric cable and the high pressure hose should always be winded carefully up around the handle C 110 2 X TRA Wind up the cable on the appropriate hook The spray handle lance and nozzles can be stored on the pressure washer 10 6 Maintenance WARNING Always discon nect th
12. the quick coupling tight on to the water inlet 2 Note The inlet filter 2a must always be fitted in the water inlet pipe to filter out sand lime stone and other impurities as these will damage the pump valves Caution Failure to fit the filter will invalidate the guarantee 1 Attach the high pressure hose 4 to the spray gun 7 Detach the high pressure hose by pressing the pawl A 4 1 Connection of high pres sure hose 4 2 Mounting of spray lance and Click amp Clean nozzles a 4 Operating your pressure washer 1 Mount the high pressure hose on the outlet 3 1 Push the spray lance 6 into the spray gun 7 and screw it on Note The spray lt lance 6 has a built in low pres sure nozzle that can be used for flushing away dirt 2 Attach the nozzle Warning When attaching the Click amp Clean nozzles the pawl on the side of the spray lance 6 should come out again Note The foam sprayer 10 features a swivel lock which must be positioned in the hole in the Click amp Clean spray lance 6 Press the pawl to detach the Click amp Clean nozzle 4 3 Water connection IC 4 4 Start and stop of the machine An ordinary 1 2 garden hose of min 5 m and max 25 m will be suitable NOTE Connection to the public mains according to regulations The spray lance is affected by a thrust during operation
13. uplings recommended by the manufacturer Do not use the appliance if a supply cord or impor tant parts of appliance are damaged e g safety device high pressure hose and trig ger gun The appliance is intended to clean cars and garden etc Appropriate ear protection has to be used Never use the machine in an environment where there could be a danger of explo sion If any doubt arises please contact the local authorities It is not allowed to clean as bestos containing surfaces with high pressure This high pressure washer must not be used at tempera tures below 0 C WARNING Inadequate extension cables can be dangerous Cables on drums should always be com pletely unwinded to prevent the cable from overheating If an extension cable is used the plug and the socket must be waterproof and comply with the below mentioned requirements for length and cable dimen sions 1 0mm max 12 5m 1 5mm max 20m 2 5mm max 30m If the electric cable is damaged it must be re placed by the manufacturer or his service agent or simi larly qualified person in order to avoid a hazard Mains power connection 9 The following should be ob served when connecting the high pressure washer to the electric installation The electric installation shall be made by a certified elec trician and comply with IEC 364 It is recommended that the electric supply to this appli ance should i
14. vents To ensure an easy connec tion and that o rings do not dry up the couplings should be greased regularly 12 7 Trouble shooting To avoid unnecessary disappointments you should check the following before contacting the Nilfisk ALTO service organization Symptom Cause Recommended action Machine refuses to start Machine not plugged in Defective socket Fuse has blown Defective extension cable Plug in machine Try another socket Replace fuse Switch off other machines Try without the extension cable Fluctuating pressure Pump sucking air Valves dirty worn out or stuck Pump seals worn out Check that hoses and connections are air tight Clean and replace or refer to local Nilfisk ALTO distributor Clean and replace or refer to local Nilfisk ALTO distributor Fuse has blown Incorrect mains voltage Machine stops Thermal sensor activated Nozzle partially blocked Replace fuse Switch off other machines Check that the mains voltage corresponds to specification on the model tag Leave the washer for 5 minutes to cool down Clean the nozzle see section 6 2 Fuse blows Fuse too small Change to an installation higher than the amp consumption of the machine You may try without the extension cable Machine pulsating Air in inlet hose pump Inadequate supply of mains water Nozzle partially blocked Water filter blocked Hose kinked Allow machine to run with open trigger u
Download Pdf Manuals
Related Search