DVR User Manual
Contents
1. Delete The cruise path setting number cruise path is a path on which the camer runs at a certain speed bypassing more than a cruise points which have serial numbers and each cruise point includes preset stop points and stop time so the cruise path settings includes the settings of cruise point preset point stop time cruising speed and other parameters and in the settings interface you can set he appropriate information At present a piece of equipment supports 16 cruise path number settings Track settings track is a irregular movement line which camer pre defines and enter settings you can set the trajectory Copy to In the select box on the right of Copy To button select the target channel click the Copy to button and the system will apply the current channel setting information to other target video channel After the page setup is completed click OK button the setting information is saved and exit click Cancel button he setting information is not saved and exit 3 8 2 9 Network Settings In the System Settings interface select Network Settings to enter the settings interface which respectively includes the Ethernet PPPOE DDNS 34 configuration Ethernet configuration In the network configuration interface select the Ethernet Configuration to enter its settings interface Physical Address It displays the physical address number of the device Port number The port number mus2. Manual Recorder Wi R23 v4 Vo PWN RV Bh ISH I6 Poors 15343 ol foanetowe a a ETS F In the setting interface respectively set the related parameters settings to the host side In Figure 1 5 3 The setting parameters is the same as that of the host For the setting methods and considerations please refer to alarm input alarm output and setting instructions of the host In the setting interface respectively set the related parameters settings to the host side In Figure 1 5 5 The setting parameters is the same as that of the host For the setting methods and considerations please refer to manual recording date time hard disk management clear the alarm log query software upgrade restoring the default turning off the system set up instructions of the host 1 5 4 User configuration information SevfPama ChasnelPem AlimPtim UsitntPaom Otter Set the user information of the device and the setting parameters are the 1 5 3 Alarm Configuration Parameters same as that of the host For the setting methods and considerations please Record and capture image to save the directory preserving path of setting path and capturing video 1 6 Remote Playback 44 45 Warranty Card Dear Customers Thanks for choosing our dvr products First please read the instructions below and then fill out the relevant content at the same time please take care of this card so that you can time
3. names can not be copied After the page setup is completed click OK button the settings are saved and exit click Cancel button the information is not saved and exit 3 8 2 4 Alarm Input In the System Settings interface select Alarm Input to enter its settings interface Input Channel Select the channel you want to set click select box to choose Alarm type you can set high low voltage please select the appropriate level for the alarm corresponding to alarm input channel connection Detection you can set whether to test alarm input signal Select Yes then the following setting functions take into force No means not to do any treatment PTZ linkage Click the Settings button to enter PTZ linkage settings interface Select a channel number and perform the relevant settings of PTZ linkage preset point cruise trajectory For PTZ setting methods see 3 8 2 8 Delay When alarm input ends the setting needs the extension of time of various treatment Buzzer Whether to trigger the alarm buzzer V means enable o means 29 invalid Video Channel When setting alarm input you need to trigger the specified video channel number Alarm Output When setting alarm input you need to trigger the specified alarm output channel number Copy to In the select box on the right of Copy To button select the target channel click the Copy to button and the system will apply the current channel setting informat
4. operating systems combined with latest technologies im the IT field such as video and audio compression decompression high capacity hard disk recording TCP IP network technology and the codes are solidatted in the FLASH which makes system run more stable The equipment at the same has the fearture of digital video and audio recorder DVR and digital video and audio server DVS which can not only independently locally but also orm a powerful network of security monitoring through being connected to network it can be used in banks telecommunications power justice transport residence factories warehouses water conservancy facilities and other fields and the safety precautions of each departments 1 2 Technical parameters Model DVR 4CH 8CH 16CH Operating System Embedded Linux Operating System system resources at the same time 4 8 16 channel CIF real time video and network transmission 1 or 4 channel CIF playback and 4 8 16 channel CIF QCIF sub stream Operation interface Graphical operation interface which supports mouse panel remote control Video Standard PAL NTSC video compression H 264 Audio Compression ADPCM video modes Manually timing alarm motion detection Video query timesearch event search channel search log search Backup modes network backup USB backup SATA DVD video input 4 8 16 channel BNC VGA output 1 way BNC 1 way video output Audio Input 4 8 16 channel BNC A
5. 2 2 Video Settings In the System Settings interface select Video Settings to enter the settings interface k e Nama Write Select channel Select the target channel you want to set click the select box to select Stream Select the code stream which needs to set which are respectively main stream and sub stream Stream type Select the needed video stream type and video streaming means only to encode the video when the system is recording video composite flow means to encode audio and video at the same time when system is recording Bit rate type Users can set fixed rate and variable bit rate and fixed rate 26 means the system encodes images according to bit rate and video frame rate which the user sets variable bit rate means the system encodes images according to image quality and video frame rate which the user sets but the bit rate is that the system automatically adjust according to the video scene Bit rate the bit rate which users select to encode according to need The higher the bit rate the better the image but the occupied disk space is larger Video frame rate the video frame rate which users select to encode according to need The higher the frame rate the better the image smooth but the occupied disk space is larger Copy to In the select box on the right of Copy To button select the target channel click the copy to button and the system will apply the current channel se
6. Due to accideht fpgistible dariy aay natural facie start playing the video file of the start time which have been set User company User __ Address Download In the search list box select the target file click File Download Information button and after setting the preserving path it starts to download the target Product Name Purchase Date file The lower progress bar shows the progress and status of downloading the Product file Product model NO Warranty Period Information Vendor Name Address Remarks The Company reserves the right to modify the obligations and the needs of final interpretation pa ee o 46
7. Multi image preview button 10 PTZ control button 2 2 DVR 4CH Product Interface Description 11 Exit button 12 Menu button 13 Recording button 14 playback button 15 Single frame play button 16 Back button 17 Speeding button 18 Previous video 19 The next video Audio IN 2 21 DVR 8CH Product Interface Description Alarmin 1 4 GND Ain2 VOUT VIN2 4 6 8 L R 2 22 DVR 16CH Product Interface Description PTZ_aB5R 2 3 Remote Control Description Remote control mode is the same as the panel DEV button after pressing DEV key according to the number keys enter device number which is agreement with the host press OK button to save the settings Then operation of the device takes into force SHIFT the current version does not support the key CLEAR when setting covering and mootion detection region clear the current constituency Note when there are more than one device in the same place remote control firstly must according to device number select a piece of equipment so defining a unique device number for each device is a must or remote control operation may at the same time make effect to more than one device which has the same device number 2 4 Video format In the video format switches on the device motherboard perform video format settings PAL format Status NTSC format Status Chapter 3 operating system instructi
8. PC is using the client you should do the following settings 1 the IE settings if the first time you use it and the control does not be loaded you need do settings for IE as follows Internet Options safe internet gt Custom Options gt ActiveX controls and plug ins are all chosen to enable and finally Click OK The following figure os H i Login Open IE and in the address bar enter the IP address which is set in the host network settings the factory IP address is http 192 168 1 23 enter the login page such as the following picture Enter the user name and login password the user name and password are the same as that of the host side and enter the correct user information then you can successfully login 39 open or close video image of the preview window of the corresponding to J eheanel 1 means to open osm means close status bain Preview mode In the preview mode switching box you can through mouse clicking CBSE or double click the preview window to switch to a single picture or multiple pictures preview mode 1 2 bit stream selection a Sa pe t 8 el The device supports dual stream and in the bit stream select box select a video preview stream type I plugin is not installed automatically please download the package and Install it manusliye 1 3 PTZ Control 1 1 Video Surveillance Main Page gt s gt After login monitoring main page co
9. Veta 2S s One fre Sanny m at fia a as oo temsa TT mem 2 amsaa fm E me r S TESE me VGA Rasodetion PPPoE MEBANE Tmepeny flew pice r tage Chee DONS r State Daphiy F DONSSmoe fon hm fie Doso Aumoana a a Revieeoat FE i err vesion Via Deedes 1 f e pe EnS In the setting interface respectively set the related parameters settings to the host side In Figure 1 5 1 The setting parameters is the same as that of the host For the setting methods and considerations please refer to system configuration system information network operating instructions of the host 1 5 2 Channel Parameters Configuration ServePasen ChaanelParam AtansPuwe UsezinsoParam Others CP s gt a ee a awm ox if Imap Pasun Ii Stow cen Nem F Stow Tan Siew Type Fite tity er Bann Ra a ee PIE Pam Bouin poo Dama fe z Spm fi fic a fo pi a z Decoder a09 fr 1 In the setting interface respectively set the related parameters settings to the host side In Figure 1 5 2 The setting parameters is the same as that of the host For the setting methods and considerations please refer to image settings video settings PTZ setup instructions of the host 43 refer to user management instructions of the host 1 5 5 Others ServerParem ChanaelPuser AlsmPerers UseiniePaonm Others Othe Coniig
10. DVR User Manual User Manual for Stand alone DVR 4ch 8ch 16ch chapter 1 product description 1 1 product overview 1 2 tehinical parameters chapter 2 intruction of product appearance struct 2 1 panel instructions 2 2 product port instructions 2 3 remote control instructions 2 4 video iTi a chapter 3 operating system instructions 3 1 start shutdown 3 2 previwes 3 3 basic operation instructions of menu 3 3 1 enter menu mode 3 3 2 composite instructions of menu 3 3 3 exit menu mode 3 4 main menu introduction 3 5 video playback 3 5 1 file search 3 5 2 search result 3 5 3 playback tools control 3 6 mannully record i 3 7 PTZ control 16 3 8 MENU cece 3 8 1 management tools 3 8 2 system settings 3 9 log information 3 10 shutdown the system client operation instructions 1 1 main page of video monitor 1 2 code stream selection 1 3 PTZ control 1 4 highly setting box 1 4 intercome ontrol 1 5 configuration 1 5 1 server parameters configuration 1 5 2 channel parameters configuration 1 5 3 alarm parameters configuration 1 5 4 user configuration information WDWMWANNNDAWWNHND 1 6 remote playback Chapter1 Product Descapgon 1 1 Product Overview The equipment is a security surveillance product which is designed specifically for the security field which adopts embedded processor and embedded
11. ctively show playback speed play progress the played time total time of video file Exit Play Click ESC key or button Oto exit playback screen at any time after playing all automatically quit the playback screen 3 6 Manual recording Click the manual recording in the main menu column to enter its settings interface Video REC key or in the main menu column use mouse to click Manual recording to directly enter manually setting recording interface 15 Manual Video Interface Description Manual recording interface consists of the following components Channel number it corresponds to the video channel of the device Channel status it indicates video status of the corresponding channel and status lights are green and o indicates that no open video red means to open the video Video status when the state lights are surrounded by a coil of and means the corresponding channel open the network video transmission When the system is in recording state regardless of video type in the lower left corner of the channel preview screen will show which means the system is recording Full enable disable the button Click the button to stop or open the video settings of all channels Back button Click the back button then exit manual recording interface return to the main menu bar Note Manually start the video only through the manually stopping otherwise the video would contin
12. dit status 5 button it s used to perform a specific function or enter the next one setting menu press confirm ENTER key and the left mouse button to determine access 3 3 3 Exit Menu mode Press MENU Exit ESC or the right mouse button to exit the menu mode and switch to a multi screen preview mode Click the right mouse button return to the previous menu level 3 4 Main Menu Introduction Press MENU key or the right mouse button to pop up the main menu main menu consists of the following three components 10 Preview mode in the menu column you can select the corresponding screen preview mode Shortcut menu in the menu column respectively have video playback manual recording shortcut menu of PTZ control you can directly emter the corresponding menu pages The main menu bar after clicking to enter include management tools system settings log query shut down the system of the menu page and so on 3 5 Video playback Click video playback of the main menu column enter file search interface 11 Pitz i3i4is5iei7is zx Baan a 5 1 File Search Select channel Select the target channel you want to search click the check box to choose Video Type Select the video type which needs to search V means to be checked o means not to be selected Time setting in the edit box enter the beginning and end time to search the video Storage device in the selection box select the targe
13. don t disconnect the power supply so as to avoid equipment failure 3 8 1 6 Time Settings 22 Enter date and time page in the Date time edit box respectively enter the exact date and time confirm the save and cancel to exit 3 8 1 7 Version You can see the device name model related information of version number 3 8 2 System Settings In the main menu page select System Settings to enter its sub menu interface 23 3 8 2 1 System Configuration In the System Settings interface select System Configuration to enter the setting interface tD Name Device number When using the remote control to remote and control operate equipment which must be through the device number communicating with the remote control the remote control must correspond to the device number to achieve remote operation For the settings of remote control device number see the 2 3 instructions 24 Equipment name device name is generally defined as the regional name of control points and when remote access you can intuitively find the monitoring point what you want to access The default device name is NetDVR For editing method see 3 3 2 4 edit box Equipment expiration When selecting coverage and when the hard disk inside the device are all fully recorded the system covers the first video data to achieve the purpose of circulating the video Keyboard lock time the system has no operatopm during the
14. e check box 2 selection box According to the options contents of the system drop down box select the target content Use 7 key or click the left mouse button to select For example in the file search menu page the Storage Device selection box 3 list box query results information display in the list you can select one of 9 the operation in the provided list to operate accordingly For example in the list of playback query results press confirm ENTER key or the left mouse button to play the file you can use the right mouse button to select cancel the video file in order to easily backup video files 4 edit box through the edit box enter the target name For example in the System Configuration menu page the device name edit box enter numbers English letters Chinese and so on a through the FN key or in the 4 click the left mouse button to switch input types including numbers case letters punctuation marks Chinese input method b through the panel lt key or the mouse cursor mobilely positioning location of the edit box press ENTER key or click the left mouse button then the enter keyboard appears through the arrow keys or clicking the left mouse button to select the target characters which need to be entered c by KSHIFGT key or click the right mouse button to delete the character before the cursor d After entering press MENU key or ESC key to exit e
15. ion to other target video channel After the page setup is completed click OK button the setting information is saved and exit click Cancel button he setting information is not saved and exit 3 8 2 5 Alarm Output In the System Settings interface select Alarm output to enter its settings interface Output Channel Select the target channel you want to set click select box to choose Alarm type Normal close type and always open type select corresponding type 30 Time period V enable valid time settings of alarm output and only during the effective setting period alarm signal can be exported After the page setup is completed click OK button the setting information is saved and exit click Cancel button he setting information is not saved and exit 3 8 2 6 video deployment In the System Settings interface select Video deployment to enter its settings interface Select channel Select the channel you want to set goals click the select box to select Weeks Select which day you want to set and you can set it separately All means all dates Video types and time periods during the four time periods you can set different video types during each period timing video red motion detection recording green alarm recording yellow V means enable o means invalid There is time period status displaying below and the overall schedule from 0 to 24 hours Copy to In the select box
16. k OK button to begin formatting the hard disk after the hard disk format is completed the hard disk can be used normally 18 Note before the hard disk formatting stop all recording 3 8 1 2 User Management Create and add users delete users and modify user information the users except Admin have no rights to set up additional user rights Create a new user Enter the User Management interface click the Add button to enter adding user interface 19 1 enter the new user name In the User Name edit box enter a new user name such as the user Note for input methods see 3 3 2 4 edit box 2 set the new user s password In the Add User interface select Set Password button enter the password setting page and directly enter the new password which is less than six figures 3 setting up new user s permissions In the Add User interface set the new operating authority for the user within the box of the corresponding function to choose and V means that the user can use the permission o means that the user can not use the permission 4 save the new user s settings Click Confirm button to set the new user information to save and Cancel means not to save Modify user Enter the User Management interface in the user list click the right mouse 20 button or panel ENTER key to select the target user and then click Modify button enter the Modify User page to modify u
17. ly and convenient access to quality services we provide you C E Tio A joia gt eee _Wontpags ff eo pares aaa Cae a Statement ee aie According to the user instructions and product labeling requirements any problem uit occurred under normal use and within warranty period you can hold the warranty card for repairs If the following occurs the company does not undertake warranty obligations 1 Beyond the warranty period 2 Improper use misuse unauthorized repair or modification 3 Commitment to the maintenance of non warranty damage caused by dismantled 4 5 FlePiaypack Flenownt sd _TimePtaysack Select video playback channel number the recording type and time conditions click the Search button then the left border will show the search result list You can scroll the page from top to bottom or enter the page number to jump to view the video file a file display 20 pieces of information and up to 4000 File playback in the search list box select the target file double click the file or click the File Playback button then the right playback window starts to play the target file and the playback control is the same as that of the host Arbitrarily demolition of the product label The product name and model number on warranty cards can not coincide with the product itself Timing playback Click Time Playback button then the playback window will 6
18. nsists of preview window PTZ control Sa preview mode stream selection channel open opening the intercom A E PTZ direction control button you can press up and down configuration playback user cancellation form Figure 1 1 left and right to control the direction of PTZ operation DLDVR remote mariapems sytem Microsoft Interne I xplorer gt B OFocus aperture button you can increase and reduce the control PTZ aperture c OZoom focal length button you can adjust nearer or farther to control O RS Orocs PTZ focus Oz00m CIBRERIES Sa Strom B D IRIS Jocation button you can pull nearer or farther to control the Gmi Cmn location of PTZ Channel 3 Cranmera A 1 4 Advanced Settings box Channa 7 aas When preview window closes the video preview the feature is activated In en et the corresponding channel preview window click the right mouse button to Cannes open the Advanced Settings box Foos o i ioe noe Ce May E Ee ss Open Close sound Through the button open or close the audio of Open preview In the preview window click the left mouse button to select the previewing the channel target channel channel which displays as a red box means to be selected and in the open box use mouse to double click the channel number which can Capture Capture the current video screen and save it as image formats For 40 41 saving the directory settings see 1 5 5 Video Capt
19. on the right of Copy To button select the target channel click the Copy to button and the system will apply the current channel setting information to other target video channel 31 After the page setup is completed click OK button the setting information is saved and exit click Cancel button he setting information is not saved and exit 3 8 2 7 Video Detection In the System Settings interface select Video Detection to enter its settings interface Tor d JESA EA Send C Select channel Select the target channel you want to set click the select box to select Type you can select motion detection video loss Video Channel Select the specified alarm output channel number which needs to trigger after detection occurred Alarm Output Select the specified video channel number which needs to trigger after detection occurred won Buzzer Whether to trigger the alarm buzzer V means enable o means invalid Delay When alarm input ends the setting needs the extension of time of various treatment Regiona Set motion detection area and the setting methods see 3 8 2 3 32 setting cover region Sensitivity Select to trigger motion detection sensitivity No detection means the above set parameters are invalid Copy to In the select box on the right of Copy To button select the target channel click the Copy to button and the system will apply the current channel setting inf
20. ons 3 1 on off Confirm that swith in current and voltage is consistent with the hard disk 6 recorder which meets requirements and ensure that middle power outlet of the hard disk recorder is well grounded After access to power the device starts POWER light which is green and after entering the system the panel RUN light normally flashes Long press POWER key for 5 seconds to make the machine soft off and the light is red then again press POWER to restart 3 2 preview After normal equipment boot immediately enter the preview screen In the preview screen you can see date time channel name of the system Press number key corresponding to panel or click the left mouse button you can preview a single image then press Panel Quard button or click the left mouse button you can return to a multi screen preview status 3 3 Basic operating instructions menu 3 3 1 enter the menu mode Main Menu MENU key to enter the device s main menu interface p A I p f 3 3 2 menu composition description Menu component units mainly consist of the following categories 1 box provide two kinds of status options means effective o means ineffective use confirm ENTER keyor ft key or click the left mouse button to choose Video REC shortcut keys enter manually recording interface For example in the file search menu page the Select Channel page and the video typ
21. ormation to other target video channel After the page setup is completed click OK button the setting information is saved and exit click Cancel button he setting information is not saved and exit 3 8 2 8 PTZ Settings In the System Settings interface select PTZ Settings to enter the settings interface Checkata Pr col i Preast Track Select channel Select the target channel you want to set click the select box to select Rate Select the rate which matches the connected PTZ Data Bits Select the data bits which match the connected PTZ Stop Bits Select the stop bit which matches the connected PTZ 33 Checksum Select the check value which matches the connected PTZ Flow Control The selected item must be consistent with the matched PTZ flow control settings Protocol Type The selected item must be consistent with the matched PTZ protocol Decoder Address Enter the address of the specified decoder Preset point setting preset point is to preset and memory position focal length aperture and zoom of camera while using a number to mark these settings Add a preset point In the pre edit box enter a preset point the range of which is 1 128 and then through the arrow keys to adjust the distance from the camera to the target location and after adjustment press setting and the preset point is saved Delete preset point In the edit box enter a preset point which you want to delete select
22. ser information Notes admin administrator can modify permissions of other users Delete User Enter the User Management interface in the user list click the right mouse button or panel ENTER key to select the target user click the delete button and after confirmation delete the user 3 8 1 3 Restore Default Restore the system configuration parameters as the factory configuration and after restore the system restarts automatically 3 1 8 4 Clear Alarm Manually remove all of the alarm information After the successful removal of alarm the system will give prompt information of has successfully cleared warning After confirmation return to management tools the page 21 3 8 1 5 Software upgrade In the management tools interface select software upgrade to enter its operation interface In the upgrade option box select objectives which need to upgrade in the upgrade option box select the upgrade mode FTP or USB USB Upgrade copy the upgrade files to the root directory of U disk plug U disk and then click OK to upgrade the system FTP Upgrade put the upgrade file into the root directory of FTP server s and set the server IP address as the specified address and finally click OK to upgrade the system After upgrade the system will automatically restart NOTE Motherboard upgrade file name must be mainboard bin Panel upgrade file name must be panel Bin When system is being upgraded
23. set keyboard lock time then the system will automatically log off the current user and it needs to re sign on system to operate Switching time switching time is cycle time period of single channel preview display Video format The device supports PAL and NTSC video output formats The default output format is PAL For setting method please refer to 2 4 VGA resolution the user can adjust the VGA display resolution according to VGA monitors Menu Transparency After entering the user operation interface you can by adjusting the level of menu transparency to achieve the transparency between the preview screen and menu Language According to the needs of users you can set the menu language type select Simplified Chinese English Status display in the preview screen set whether to display video mode status and open the information icon of motion detection which is marked as wow V to show state it s marked o as non display status Icon status description in the lower left corner of vhannel preview screen B Indicates that the system is recording video regardless of video type D Indicates timing recording status D means the manual recording status 25 means Motion Detection Status wk 4 means Motion Detection recording After the page setting is completed click OK button the settings are saved and exit click Cancel button the setting information is not saved and exit 3 8
24. t backup storage device Search files button after setting the search criteria click the button then the system begins to search the corresponding video files and enter the search results interface NOTE If video files meeting the search criteria are more than 4000 then the system only shows the latest 4000 video files If you want to find the updated files please modify the search criteria Playback By time According to set starting and ending time to start playback of video material No distinction of video types playback tools control please refer to 3 5 3 By time backup Backup all video data to the designated storage devices during the set beginning and ending time 12 3 5 2 Search Results After setting search criteria click File Search button then enter the search results interface Playback video files in the search results list box through the upper and lower key or moving the mouse to position the target file click the ENTER key or left mouse button to start playing the file page curl Display searched video file by page you can click Previous Next 13 button or in the page number box enter the target page and click the Go button to curl page and you can also scroll the middle button of mouse to next Page Backup In the search results list through the upper and lower key moving the mouse to target file and then use the FN key or the right mouse button to select the file in
25. t be greater or equal to 2000 IP Address The IP address must be unique and can not conflict with any other host or workstation on the same network Subnet Mask It s used to divide the network segment Default Gateway It s used to achieve communication among the different 35 network segments rwhich needs to set the gateway address DNS Address The device uses PPPoE protocol to access network and it will get a dynamic IP address Enable Multicast Select whether to enable multicast DHCP Select whether to enable DHCP to automatically obtain IP http port The port number which IE is browsering to visit and the default port number is 80 When the page setup is completed click OK button and the setting information is saved and exit click Cancel button the setting information is not saved and exit PPPOE configuration In the network configuration interface select the PPPOE Configuration to enter its settings interface 800 Enable V means to enable PPPoE to dial up o means not to enable the feature The user name and password In the edit box enter the user name and password which the ISP provides For editing method see 3 3 2 4 edit box When the page setup is completed click OK button the setting information is 36 saved and exit click Cancel button the setting information is not saved and exit DDNS configuration In the network configuration interface select the DDNS Config
26. the storage equipment selection box select the target storage devices and then click Backup button then the selected video file will be backed up to the target storage device Cancel button return to the previous menu level 3 5 3 Playback Tool Control When selecting the file playback or playback by time it will enter the video playback interface Playback toolbar In the bottom of playback interface playback toolbar will appear and you can click the right mouse button to hide show toolbar When at the same time Multi screen is being playback after hiding tool bar you may by clicking the left mouse button zoon in or out corresponding channel video Stop Play Click button the system will stop playing and exit the playback 14 interface Pause Play Click T button to pause playback click to continue to video playback Single frame playback when it is pause mode click it will be single frame playback and each time click to forward play one Slow play Click to slow play click again to set the slow play multiples Quick play Click to slow play click again to carry out quick play multiple settings Previous paragraph next paragraph Click or button every time click once of a time or the next section playback progress will forward or backward progress 10 Close Open Sound click lor Bean open or close the sound of playback files Playback status information on the right playback tool bar respe
27. ting box The creation of the region through the panel arrow keys moving the yellow box to the beginning position of the established region press FN key to yellow box switches to the red box each other turn it into a red box red box is the cover region box which takes into force and then press the arrow keys to adjust the size of the region and the minimum can be set to a small square and the maxium can be set up to four cover areas Click the left mouse button or long press left button to move the mouse to select area and after selection you can press ENTER key or click the middle button of mouse to exit and save ESC key not to save and exit Partial elimination mave the yellow box to the start region which need to be eliminated upper left press FN key to enter a small black box to eliminate the regional boxes and the localized area is eliminated After elimination press confirm ENTER key to save and exit and if you press exit ESC key the elimination operation is invalid In the red box click the left mouse button or long press left key to move mouse to eliminate area click the middle button of mouse to exit and save Clear All Press MENU to clear all covered areas of the channel Copy to In select box on the right of the Copy To button select the target channel click the Copy to button and the system will apply the current 28 channel setting information to other target video channel Note Channel
28. tting information to other target video channel When the page setup is completed click OK button then the settings are saved and exit click Cancel button then the setting information is not saved and exit 3 8 2 3 Image Settings In the System Settings interface select Image Settings to enter the settings interface Select channel Select the channel you want to set click the select box to select 27 Channel Name In the edit box the user own can edit the channel names For the edit method see 3 3 2 4 edit box Display Name V means display o means not to display Click Location button to enter the setting interface you can via panel keys or the mouse dragging the red channel name to set and after set up press ENTER key or right mouse button to save and exit press ESC key not to save and exit Image parameters Respectively configure the brightness contrast hue and saturation of channel imag use the panel t keys or the mouse to drag scroll to adjust Use the default values By clicking the button you can restore the setting image parameters to the system default value only limited to restore the image parameters Cover in the cover option tag set V thereby active button of the cover regional to confirm to enter cover region setting interface Set cover region In the setting interface of cover region a small yellow box appears in the regional center that is the cover set
29. udio Output 1 channel BNC Monitor quality PAL 720x576 D1 NTSC 720x480 D1 Playback quality PAL 352x288 CIF NTSC 352x240 CIF Image Control 6 speed adjustable Motion Detection the detection area of each channel 16 x 16 which can be set multi level sensitivity Screen display 1 4 8 9 16 screen display Video rate PAL 25 frames sec adjustable NTSC 30 frames sec 2 adjustable Backup hard drive network Local playback 1 or 4 way playback at the same time Alarm Input 4 switch input Alarm output 1 switch output PTZ control RS485 hard disk interface 2 SATA interface Network interface RJ45 10M 100M self adaptive Ethernet port USB interface a USB2 0 high speed interface a USB1 1 interface Power 12V 3A 5A chapter 2 intruction of product appearance struct 2 1 Panel Description 2 1 DVR 4CH Panel Description 1 Single channel shift button 9 Direction key 2 4 video loop preview button 10 Confirm button 3 Manual Recording button 11 The power indicator 4 Menu button 12 System running light 5 Auxiliary key 13 USB condition indicator 6 PTZ control button 14 Recording condition indicator 7 Playback button 15 Infrared receiver 8 Exit button 2 11 DVR 8CH 16CH Panel Description The power indicator System running light The hard disk light Remote control receiver Power switch button Direction key Confirm button Numeric button 0 o s Cea N es
30. ue B 16 3 7 PTZ Control Click PTZ control of in the the main menu column to enter setting interface The main operations of PTZ control are directional control horizontal sweep zoom control adjust the focal length adjust aperture PTZ speed After switching page you can call the preset points start stop automatic cruise wiper control lighting control auxiliary equipment control Description The called preset points must be set up and for the cruising path setying method see 3 8 2 8 PTZ settings in which when the set cruise path number is less than 2 digits you need to add 0 to make up enough numbers before the value of the set corresponding cruise path number 3 8 Menu Click menu in the main menu column to enter the main menu page and one level menu includs management tools system settings log Query shut down the system 3 8 1 Management Tools It includs hard disk management user management restore to the default clear the alarm software upgrades time settings version information 17 3 8 1 1 Hard disk management SATA It displays hard disk information of the current system o means the success of the hard disk test X indicates means not to detect the hard disk Hard Format In the hard disk select box select the target disk and you can view the information corresponding to the hard disk click Format button to turn up a confirmation page clic
31. uration to enter its settings interface Enable V means to enable DDNS Dynamic Domain Name Service o means not to enable the feature Select the corresponding service providers and in the edit box enter the user name password and domain name For editing method see 3 3 2 4 edit box When the page setup is completed click OK button the setting information is saved and exit click Cancel button the setting information is not saved and exit 3 9 log information In the main menu page select Log query to enter its interface 37 Main types in the selection box select query log types Time setting in the edit box enter the view time period Click the Search Logs button and the corresponding log information will appear at the bottom of the log list You can through in the Page box entering the target page click OK button to curl or scroll the middle mouse button to curl 3 10 shutdown the system In the main menu interface select shutdown system to enter its interface ort In the selection box select corresponding operation content Cancel the user It s user to exit the current user After cancelling if you want to continue to use the equipment you need to re login the system 38 Restart Restart the device and after confirmation the device will restart Close system Close the device and after confirmation the device will be closed Client Instructions When the
32. ure save directory Video Turn on remote recording of the channel video and save it For saving the directory settings see 1 5 5 Video Capture save directory PTZ settings It s used to set PTZ preset point the cruise path trajectory settings For setting method see 3 8 2 8 PTZ host side settings OSD Setting Set the channel time real location of OSD layer use mouse to drag location to confirm and save Motion Detection Set motion detection area firstly V means motion detection area select Add area hold down the left mouse button to drag on the screen then grid like white line appears which is detection area select clear the area in the region of the grid like white lines hold down the left mouse button to drag on the screen then the region of the grid like white lines disappears and the motion detection area is cancelled In the sensitivity and output delay box select the corresponding parameters Screen adjustment Set the image brightness contrast hue saturation and click the left mouse button or drag to adjust when exiting it is automatically saved 1 4 Intercom Control Click to open the Voice to initiately perform voice intercom This version doesn t temporarily support voice intercom 1 5 Configuration 1 5 1 Server Parameter Configuration 42 Siiman CanePem Arrosa UsdaSiPute Otte Seat l Deine RaR Pas fi i 1 a enit OINEI Post Ea a
Download Pdf Manuals
Related Search