Polycom® KIRK IP Interface Card
Contents
1. Orina z Packetstze ims Exclusive Siere compression Most 1722020252 Statue ready osne 5 Registration of Users on the CallManager Users have to be registered on the CallManager as well as on the KIRK IP Interface Card Please follow the steps below to register users on the CallManager Start the CallManager software Select Device gt phone Select add a new phone In the field phone type select Cisco 7940 and press next Type a description of the handset in the field description Select Default in device pool and press insert Type the extension number in the field directory number and press insert Ensure that call waiting is turned off for all DECT Phones 1 2 3 4 5 Type i e the handset serial number without space in the field MAC address 6 7 8 9 1 0 Please note that the wireless system supports automatic registration 6 Subscription of Users on the KIRK IP Interface Card How to register users on the IP card 1 Open the IP Interface Card with an internet browser 2 Select Gateway gt users gt new user Name some name you choose Nickname Prefix SEP and then the IPEI number without spaces i e SEP000770669569 This number must be the same as the one given in the Call Manager A http 172 18 0 170 GW DECT gwuser L xml xsl usereditas Gateway user edit Nickname Number Display IPEI Po AC access c2. GW DECT Set protocol to Skinny 5 Type the IP address of the Gatekeeper Primary Call Manager IP 6 Type the IP address of the alternate Gatekeeper Secondary Call Manager IP 7 Type DECT1 in HW ID 8 Check the enable user directory box 9 Press Save gt Activate 10 No other fields are supported gt gt Ntpe 172 29 202 Seong him Save Activate Reset Resetwnen idie Cancel Remove Add IP route DHOP DHCP Mode off x Config General settings th SNMP n n l Logging Ethemet interface adores t DECT Interface IP address 172 IP interfaces By IP subnet mask 265 Defaut IP router Dotauh router 172 DNS ONS server agarose Advanced T Do peomparP Enel Link options auto j VLAN T Use VLAN header Note Use VLAN header only the ewitthes and endpoints tuppo Note Leave VLAN id empty for priority tagging PPP 14 interface PPP15 interface 802 1p Prionty NAT LDAP Ri aton B0210 VLAN id Host 17229720252 Status ready 2 112 29 202 52 Config KIRK ipdect 500 Windows Internet Explorer E Ntp 172 29 202 S2icortig hime Save Actrate Reset Resotwnen ise Cancer Remove Contig DECT Gateway General setings Description SNMP Gateway name Configuration F Trato t Protocol Gatekeeper IP agarose 172 Ak Gatekeeper IP Gatekeeper ID Diattone tne Dusy timeout s Volume 31 32 Codec Configuration Standard
3. the system is running and the subscriptions are read Software and help files are available at http www kirktelecom com Installers suk227 asp 3 IP Addresses The KIRK IP Interface Card is configured with the IP address 192 168 0 1 as a standard This address has to be changed for customizing the sub net mask of the network Start configuring the PC to the IP system s identical net mask e g the address 192 168 0 2 and sub net mask 255 255 255 0 The system is now ready to be reached witha standard internet browser To change the address in the card to e g 10 1 1 150 please follow the steps below 1 Start an Internet browser and address the card with IP 2 172 29 202 57 Config KIRK ipdect1500 Windows Internet Explorer address 192 168 0 1 2 Select Gateway gt Config user admin password ip1500 3 Select IP Interfaces gt Ethernet Interface in the pop up window 4 It is now possible to change the IP address of the card and the IP address mask Type the new IP address in the IP address field and press save gt activate Type the default router if applicable No other fields are supported Select IP Interfaces Type off service must be set to 0xb8 and press save gt activate Me Noy 01 4 Configuring the KIRK IP Interface Card to the CallManager 1 Start an internet browser and address the card 2 Select Gateway gt Config user admin password ip1500 3 Select DECT Interface gt
4. Polycom KIRK IP Interface Card User Guide 1 Introduction This guide helps you setting up the KIRK Wireless Server 1500 with IP Interface Card on a Cisco CallManager Please refer to your CallManager user manual for general information 2 Installation 1 Power down the WMS Wireless Mobility Server 2 Remove the top cover by unscrewing the screws on both sides of the WMS and the screws at the rear panel 3 Remove the blind cover plate in front of the slot closest to the power supply please refer to the figure at right Z gure at rig 4 Insert the KIRK IP Interface Card into the slot 0 see drawing and mount the two screws from the F 4 blind cover 5 5 Put back the top cover 6 Connect an RJ45 cable not included between the KIRK IP Interface Card on the back of the WMS and the LAN network 7 Power up the WMS again 8 Verify that the LED s are flashing as follows Active In HTTP mode and when packets are transmitted on the Ethernet the Active LED is turned on 100 In HTTP mode and when the Ethernet speed is 100mbps the 100 LED is turned on When 10mbps Ethernet is connected it will be off Link When the Ethernet link layer is established the Link LED is turned on Ready When the system is running and ready the Ready LED is turned on If the system is not ready the LED will start flashing In TFTP mode the Ready LED is flashing and all other LED s are off Front LED The front LED is green when
5. a confirmation tone Step 2 Hang up Call Pickup NOT SUPPORTED FOR SRST To answer a phone in your call pickup group follow these steps Procedure Step 1 Press the hook key and dial then 3 on your telephone keypad 10 Note Cisco charges users of the CallManager software a license fee for each IP Phone soft phone or other endpoint system IP Phone that connects into the Cisco CallManager software This CallManager user license fee applies regardless of the source Cisco Licensee or a third party or the functionality of that IP phone Licensee must communicate to Licensee s field channels and customers in a form and manner approved in advance by Cisco the following information about the program How to make payment of that CallManager User License Fee under a particular part ID number URL to be provided to Licensee by Cisco or customers may contact their Cisco Field representative to make payment 14184602 Ed 1
6. ode Po Password ok Remove Cancel Note IPEI is the serial number of the handset as in this example 00077 2300000 Number The extension you choose for the phone The number must be unique e g 320 Display The stand by display text of the handset IPEI The IPEI number of the handset is located in the battery casing of the handset If the battery compartment is not accessible i e on newer KIRK handsets the IPEI number can be seen in the display by typing 99984 ENTER v AC access code optional An access code can be defined for the handset login procedure Password Not supported 7 Subscription of Handsets Before registering handsets on the system the system oo 02 SASS must be set to subscription allowed The subscription setting can be changed in the info menu Gg Annasan x rante ns 1 From the handset choose the SUBSCRIPTION CREATE menu to subscribe to the new system Use the lt and gt keys to scroll between the Id s of the different systems if there are more than one system available If the handset is already subscribed to 10 systems you will need to remove one of the existing subscriptions 2 Choose the system that you wish to subscribe to When a subscription is available enter the free system using lt or gt and the AC if required 3 If the subscription was successful the standby text and the speaker icon is shown in the display If not the subscription has failed and the
7. procedure must be repeated 4 For re subscription of a DECT handset that has previously been subscribed to the CallManager it may be necessary to reset the handset from the CallManager after subscribing the handset Please refer to the KIRK 3040 handset user guide for further reference 8 Remove a Subscription from the System If you wish to remove a subscription from the system it is very important that the subscription is removed FIRST on the KIRK IP Interface Card and then on the Call Manager 9 Firmware Upload It is possible to upload new firmware to the system Download the newest firmware from www kirktelecom com Choose firmware update from the menu and locate the bin file Do not interrupt the system while the firmware is being uploaded The system needs to be restarted for the new firmware to function properly 10 Pre Call Services Activate Call Forward All Use this feature to send all calls from one telephone number to another telephone number To activate Call Forward All follow these steps Procedure Step 1 Press the hook key and dial then 1 on your telephone keypad You will receive a confirmation tone Step 2 Enter the telephone number to which you want to send the calls A confirmation tone will sound Step 3 Hang up Cancel Call Forward All To cancel Call Forward All follow these steps Procedure Step 1 Press the hook key and dial then 2 on your telephone keypad You will receive
Download Pdf Manuals
Related Search