User`s Manual - Samsung CCTV
Contents
1. AWC SET MANUAL e LOW e MIDDLE e ZOOM D Z00M e ZOOM POS INIT e SMART ZOOM END EXPOSURE BRIGHTNESS AGC END IRIS e SHUTTER e SSNR e SENS UP SPECIAL e USER PRESET e SYNC END e PRIVACY COMM ADJ DAY NIGHT IMAGE ADJ Use the six buttons on back of the camera SET button an AF button UP button LEFT button DOWN button 1 Press the SET button to access the main setup mode Main setup menu is displayed on the monitor screen 2 Select the desired feature using the UP or DOWN button e Each pressing of the UP or DOWN button moves the indicator to the next or previous feature e Move the arrow indicator to the desired feature item Change the status using the Select feature using the UP p CAM TITLE LEFT or RIGHT button or DOWN button 3 Change the status of the selected feature using the LEFT or RIGHT button 4 When completed move the arrow indicator to EXIT and press the SET button e Features marked with a J have an accessible submenu e Access the submenu by pressing the SET button Use this feature to designate a name for the camera which will display on the monitor screen 1 Press the SET button to display the main setup menu and move the arrow indicator to CAM TITLE using the UP or DOWN button 2 Set CAM TITLE to ON using the LEFT or RIGHT button 3 f the CAM TITLE featur2. Use this feature to horizontally COLOR GAIN inverse the screen e V REV Use this feature to vertically inverse the screen eSHARPNESS _ Increasing this value sharpens object edges Too high of a setting however produces noise and may obscure the image e COLOR AGAIN Adjusting this value affects the chroma level only the burst level is unaffected END evert back to the USER PRESET menu To reset your camera to factory default condition To finish setup menu Troubleshooting Specifications Refer to the following table if you are experiencing trouble with your camera SVD 4300 W N SVD 4300 W P Contact an authorized technician if the table does not provide you with a Input Voltage 24 10 DC 12V 1096 solution to the trouble Input Current 290mA Steady state 460mA Zoom Focus Day amp night motor operating Problem Solution E Power Consumption DC12V AC24V 3 5W Normal No display e Check the power cable and the wiring between the 5 5W Max Zoom Focus Day amp Night motor operating camera and the monitor c Sie 1 4 inch Interline Transfer CCD Ensure proper video cable connection Video Out C Total Pixels 811 H x 508 V 795 H x 596 V Jack D Effective Pixels 768 H x 494 V 752 H x 582 V B Optics 10X f 3 8 to 38 0mm F1 8 Dim display e The lens could be dirty Clean with a soft clean T Min Focus Distance 1 500mm piece of cloth 1 D zoom OFF ON X2 X10
3. e Adjust monitor settings 5 Angle Field of view Appr 51 2 Wide to 5 58 Tele V Appr 39 3 Wide to 4 27 e Adjust camera position if exposed to a strong light S Scanning System 2 1 Interlace source Synchronization Internal Line Lock C Frequency H 15 734KHz V 59 94Hz 15 625KHz V 50 00Hz Dark display e Adjust the monitor s contrast level Resolution 500 TV Lines Min Color WIDE 570 TV Lines Min B W WIDE e Set the intermediate device if in use to 75 2 Hi z Video Output CVBS 1 0Vp p 75 X VBS EXT refer to p 13 SIN Y signal 50 dB AGC Off Weight ON Min Illumination 0 7LUX F1 8 0 005LuxQF1 8 Sens up Color 0 02LuxQF1 8 B W The camera is not functioning Check the power source for compliance with Backlight Compensation LOW MIDDLE HIGH OFF Selectable properly and its surface is hot specifications Day amp Night Auto1 Auto2 COLOR BAW ICR Gain Control Normal High OFF Selectable Motion Detection e Ensure that the feature is set to ON White Balance ATW INDOOR 3 000K 10 500K OUTDOOR 1 800K 10 500K AWC MANUAL feature is not active L AUTO X128 1 60sec 1 120 000sec AUTO X128 1 50sec 1 120 000sec E oi shutter Sens up and Sens up Limit is Sens up and Sens up Limit is Uneven colors e Adjust and configure WHITE BAL cE selectable Flickerless selectable Flickerless Flickering e The camera may be facing the sun or a fluorescent 0 5 0 Built In light Adjust the position
4. establishment if press SET button after select SMART smart zoom serue ZOOM article in FOCUS SETUP MENU E o 7 e MODE You can establish mode using left or right button TARGET 200M START ZOOM You use left or right button in EE START ZOOM article you can select zoom position to return after SMART ZOOM action from 1 times to 9 times ZOOM When uses one side or right button in TARGET ZOOM article and senses motion you can select zoom position to act from 2 times to 10 times eDWELL TIME You use left or right button DWELL TIME article You can choose time to delay before return to START ZOOM position after zoom motion at TARGET ZOOM position from 1 second to 20 seconds END To revert to the main setup menu 1 Press the SET button to access the main setup menu and then position the indicator over EXPOSURE using the UP or DOWN button 2 Press the SET button to confirm OBRIGHTNESS Use this feature to adjust image brightness Position the indicator over BRIGHTNESS using the UP or DOWN button Then increase or decrease brightness level using the LEFT or RIGHT button while verifying the changes on screen Set END once desired level is obtained OIRIS Set IRIS to AUTO or MANUAL Position the indicator over IRIS using the UP or DOWN button and then select the desired iris mode using the LEFT or RIGHT button AUTO e AUTO The iris is
5. SPECIAL Only use the camera under conditions where temperatures are between 10 C and 50 Be especially careful to provide ventilation when operating under high temperatures Severe lighting change or flicker can cause the camera to work improperly It can cause the image quality to be poor It is one of the most important parts of the camera Be careful not to be stained by fingerprint It can cause malfunctions to occur It can damage the CCD 4 8 4 If it is exposed to radioactivity For heated CCD it will be out of order e f the camera is exposed to spotlight or object reflecting strong light smear blooming may occur Please check that the power satisfies the normal specification before connecting the camera 1 7 SVD 4300 m 040 7 Installation Video Output S Pan Base control panning angle of camera Rotate Base Holding Screw fix rotated position Rotate Base control rotating angle of camera Pan Base Holding Screws Color Silver fix panned position Auto Focus 10x Zoom Lens Module SET button To access the main setup menu Pressing the SET button locks the zoom control functions of these buttons and prompts the main setup menu button To activate auto focus just once WIDE button To move the arrow indicator to up To widen the view ZOOM OUT DOWN TELE button To move the arrow indicator to down To close in
6. fast eSLOW To move zoom slowly 3 CNotes e ZOOM SPEED mode cannot be used if MODE is set to AUTO and 700 TRK is ON D ZOOM Configure magnification limit from x2 x10 using this feature Position the indicator over D ZOOM using the UP or DOWN button Set 200 to ON and press the SET button to confirm Set ZOOM LIMIT to the desired level using the LEFT or D 200M LIMIT SETUP RIGHT button LIMIT X2 END DISP ZOOM MAG Use this feature to display the current zoom magnification level on screen Position the indicator over DISP ZOOM using the UP or DOWN button Then set to ON using the LEFT or RIGHT button 2008 MAG ZOOM POS INIT Configure zoom position using this feature Position the indicator ove ZOOM POS INIT using the LEFT or RIGHT button Y Preset setting has priority over a ZOOM POS INIT setting LENS INIT Use this feature to initialize the lens 1x WIDE Position the indicator over LENS INIT using the UP or DOWN button Press the SET button to confirm IHIT SMART ZOOM SMART ZOOM is acted by motion perception SMART ZOOM acts zoom as TARGET ZOOM that is established if motion is sensed Condition when all MOTION DET MODE and SMART ZOOM MODE are ON SMART ZOOM returns as START ZOOM after delay as DWELL TIME establishing after action PSMART 2000 You can change SMART 700 function 1 1
7. on a far object ZOOM IN S LEFT F NEAR button To move the arrow indicator to left To see a near object clearly qp RIGHT F FAR button To move the arrow indicator to right To see a far object clearly Video Output Terminal to Monitor Power Input Jack Video Output Jack S RS 485 Control Cable The detailed description refers to p15 9 Dome Cover Shield Case e The zoom postion is saved after 5 seconds when you set zoom function Connect the VIDEO OUT jack to the VIDEO IN jack of monitor CCTV Camera Monitor As the connecting method varies with the instruments refer to the manual supplied with the instrument e f necessary can connect the monitor to the REMOTE jack on the back of your camera e Only connect the cable when the power is turned off e Set the 750 Hi Z selection switch as shown below if you have an intermediate device Intermediate monitor CCTV Camera Use AC 24V 300mA or DC 12V 500mA power source White L a For DC power as the voltage drop according to the length of the cable in the above table a camera may malfunction if there is an excessively long cable run Resistance of copper wire at 20C 68F Copper wire size AWG 18 0 83mm 08 CDS 1 0018 Voltage Drop V m Voltage for camera operation 12V DC 10 Voltage drops in the above table are variable according to types of cable manufacturer
8. than that specified Do NOT expose this appliance to rain or moisture This installation should be made by a qualified service person and should conform to all local codes Features A F 10x Optical Zoom The built in SVD 4300 optical zoom lens is a highly durable component It features auto focus auto iris and zoom functions SSNR Samsung Super Noise Reduction By using built in SSNR function manufactured by SAMSUNG TECHWIN the amount of low illuminance noise has been significantly reduced and the signal to noise ratio S N as well as horizontal resolution have been improved resulting in a clear and sharp image display even in the dark High Sensitivity The built in high sensitivity COLOR CCD enables a clear image even in 0 005Lux Sens up color or lower illumination High Resolution Featuring 500TV line horizontal resolution in color mode and 570TV line horizontal resolution in BW mode the camera features Sony s 410 000 pixel CCD and captures clean noiseless high quality images Day amp Night The camera automatically determines whether it is night time or day time selecting operating mode automatically The camera operates in color mode during day light conditions and BW mode in night conditions for clearer identification IP66 Approved Dust and Rain Resistant With dust and rain resistant design the camera can be installed outside under building eaves or places that are exposed t
9. Be sure to connect power only after all the installation is complete e Note that AC or DC adaptor is not supplied with camera Use the UL listed class 2 power transformer of AC 24V adaptor e Ground should be connected to the GND terminal CONTROL CABLE SPEC RED TRX RS 485 WHITE TRX RS 485 Using a RS 485 communication it will be able to control the ZOOM FOCUS and OSD menu at the SAMSUNG TECHWIN System Controller or DVR 1 The case which it controls from the PC Using a RS 485 converter It connects to RS 485 control cable outside camera and serial cable EX SERIAL PORT OF THE PC COM1 SERIAL CABLE RS 485 CONVERTER RS 485 CONTROL CABLE 2 The case which it controls from the DVR or System Controller It connects the RS 485 control cable in the connection terminal of 485 control boards which are connected with the DVR or System Controller 485 CONTROL BOARD CONNECTION TERMINAL RS 485 CONTROL CABLE CONNECTION TERMINAL RED TRX CONNECTION TERMINAL WHITE TRX S e When you construct external control systems for a camera control please use to the SAMSUNG TECHWIN PROTOCOL or PELCO D PROTOCOL e When you connecting to RS 485 control cable please peel off the outer skin inside the RS 485 control cable CAM TITLE WHITE BALANCE BACKLIGHT MOTION DET FOCUS MAIN SE OFF e ATW OUTDOOR OFF e HIGH OFF MODE e ZOOM SPEED DISP ZOOM MAG LENS INIT TUP MENU
10. NSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with an arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons INFORMATION This equipment has been tested and found to comply with limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance WARNING Changes or modifications not expressly approved by the manufacturer could void the user s authority to operate the equipment WARNING To prevent electric shock and risk of fire hazards Do NOT use power sources other
11. SAMSUNG TECHWIN SALES NETWORK SAMSUNG TECHWIN CO LTD 145 3 Sangdaewon dong Jungwon gu Seongnam si Gyeonggi do 462 120 Korea TEL 82 31 740 8151 8 82 31 740 8145 SAMSUNG TECHWIN AMERICA LTD 1480 Charles Willard St Carson CA 90746 UNITED STATES TEL 1 310 632 1234 FAX 1 310 632 2195 www samsungtechwin com WWwW samsungcctv com SAMSUNG OPTO ELECTRONICS UK LTD Samsung House 1000 Hillswood Drive Hillswood Business Park Chertsey Surrey KT16 OPS TEL 44 1932 45 5308 FAX 44 1932 45 5325 P No Z6806 0750 01D VAN 08 12 High Strength High Resolution 10X Vandal Proof Dome Camera SVD 4300 User s Manual Thank you for purchasing a SAMSUNG CCD CAMERA Before attempting to connect or operate this product please read these instructions carefully and save this manual for future use ENGLISH Before operating the camera confirm the camera model and proper input power voltage In order to that you can understand this manual thoroughly we ll introduce our model description SVD 4300 SERIES eNTSC MODEL ePAL MODEL SVD 4300 W N SVD 4300 W P MODEL DESCRIPTION e SVD 4300 W X SIGNAL SYSTEM CAMEA COLOR e SIGNAL SYSTEM NTSC MODEL P PAL MODEL e CAMERA COLOR SILVER COLOR W IVORY COLOR CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS I
12. automatically activated upon illumination eMANUAL Manual iris configuration Set IRIS to MANUAL using the LEFT or RIGHT button and then press the SET button Increase or decrease iris level using the LEFT or RIGHT button while verifying the changes on screen SHUTTER Control image brightness by adjusting shutter speed 1 Position the indicator over SHUTTER using the UP or DOWN button Then select the desired shutter mode A FLK ESC MANUAL using the LEFT or RIGHT button A FLK NTSC 1 100 PAL 1 120 Flicker free mode eESC Automatic shutter speed setting optimal eMANUAL Manual shutter speed setting If you choose MANUAL select the optimal shutter speed MANUAL mode the optimal shutter speed needs to be designated Select from 1 60 to 1 120 000 NTSC or from 1 50 to 1 120 000 PAL Sens Up mode can be configured manually 2x to 128x Verify changes made to the shutter speed by referencing to changes in on screen brightness SHUTTER VAL e mage may become unstable if the camera is set to ESC mode and faces a strong fluorescent light e Under ESC mode the brightness can be adjusted using the LEFT or RIGHT button WDR feature is not available under MANUAL mode e Sens up is disabled under MANUAL or A FLK mode Auto Gain Control For brighter images 1 Position the indicator over using the UP or DOWN button 2 Set to the desired mode
13. e is set to OFF TITLE the name will not displayed in the monitor 3 Press SET button m CAM TITLE SETUP ABCDEFGHIJKLMNO PORSTUVWXYZabcd efghijklmnopqrs tuvwsyz01234567 89 H CLR POS END 4 You can enter up to 15 characters Move the cursor to the character entry field using the LEFT or RIGHT button Use UP DOWN LEFT and RIGHT buttons to select a desired character CAM TITLE SETUP ABCDEFGHIJKLMNO PQRSTUVWXYZabcd efghijklmnopqrs tuvwsyz01234567 89 I CLR POS END Press the SET button to confirm selection of the blinking character The character is then saved and the cursor in the entry field moves to the next position Repeat steps through until the desired name has been entered e Correcting Mistakes Move the cursor to CLR and press the SET button to clear the entire entry To modify one character use to position the cursor above the character to be modified and click the SET button after selecting the character to enter 5 Select on screen position of the CAM TITLE Move the cursor to POS and press SET button CAM TITLE SETUP ABCDEFGHIJKLMNO PQRSTUVWXYZabcd efghijklmnopqrs tuvwsyz01234567 89 31 CLR POS END amp The CAM TITLE is displayed on the top left of the monitor screen Default position Select the position by using the 4 directional buttons then press the SET button t
14. n Special Mark Messages Ignoring this information may result in material loss and or serious personal injuries including death Indicates Never Allowed Indicates No Disassembling Indicates Must Observe Correct Disposal of This Product Waste Electrical amp Electronic Equipment Applicable in the European Union and other European countries with separate collection systems It This marking shown on the product or its literature indicates that it should not be disposed with other household wastes at the end of its working life To prevent possible harm to the environment or human health from uncontrolled waste disposal please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources Household users should contact either the retailer where they purchased this product or their local government office for details of where and how they can take this item for environmentally safe recycling Business users should contact their supplier and check the terms and conditions of the purchase contract This product should not be mixed with other commercial wastes for disposal m Connecting To Monitor m Connecting To Power m RS 485 communication control m Menu Configuration m Menu Setup IX 7272 CAM TITLE e WHITE BALANCE ooo 21 s BACKLIGHT or e a A E A E T EE 22 s MOTION DETECTION a 23 e FOCUS E A E E 29 e
15. o confirm the position 6 When completed move the cursor to END and press SET button Your camera provides three WHITE control modes for your choosing in adjusting the white balance 1 Press the SET button to access the main setup menu and move the indicator to WHITE BAL using the UP or DOWN button 2 Set WHITE BAL using the LEFT or RIGHT button The three white balance control modes are as follows OATW Auto Tracking White Balance OUTDOOR This mode can be used within the color temperature range 1800 10500 Ex fluorescent light outdoor sodium vapor lamp or inside tunnels INDOOR This mode be used within the color temperature range 3000 10500 AWC Auto White balance Control The white balance is automatically adjusted in a specific environment In order to obtain the best result press the SET button while the camera focuses on white paper If the environment including the light source is changed you have to adjust the white balance again Manual To fine adjust select the Manual mode You can increase or decrease the red or blue factor while monitoring the difference on the screen Set to MANUAL mode and press the SET button Increase or decrease the value for red R Gain and blue B Gain watching the color of the picture and press the SET button when you obtain the best color Operating Your Camera Proper White Balance may not be obtained under the follo
16. o the dust and rain RS 485 Function The camera using a RS 485 communication can remote control relate to ZOOM FOCUS and OSD menu functions Sub Monitor Function The sub monitor function enables easy adjustment of the camera angle within the monitoring range during its installation 3 Axis camera mechanism The SVD 4300 is especially incredibly flexible to install with its 3 axis camera construction which makes the camera wall or slope mountable Miscellaneous Functions Other miscellaneous functions of the camera include privacy zone masking digital zoom line lock synchronization INT LL freeze horizontal inversion and user configured presets Samsung Techwin cares for the environment at all product manufacturing Stages to preserve the environment and is taking a number of steps to provide customers with more environment friendly products The Eco mark eco represents Samsung Techwin s will to create environment friendly products and indicates that the product satisfies the EU RoHS Directive RoHS compliant _ Warnings amp Cautions This information is provided to ensure your safety and to prevent any losses financial or otherwise Please read it carefully and use the product accordingly For product inquiries please contact the retail shop where you bought the camera The use of equipment such as an aerial ladder while providing after sales service shall be at your expense Warning Attentio
17. of the camera Motion Detection ON OFF 4 Programmable Zone per Screen SSNR Low Middle High Off Can t select LL mode e The camera may be connected to a DC power Focus Auto Manual One push source Connect to an AC power source Zoom Movement Speed 1 67sec Wide to Tele 1 75sec Wide to Tele IRIS Control Auto Manual LL is not function e Check external SYNC signal frequency should be Lens Initialize Built In properly 60Hz for NTSC 50Hz for PAL Camera Title OFF ON Displayed 15 characters COLOR CCD CAMERA 40 User s Manual COLOR CCD CAMERA 41 User s Manual Communication Privacy Function FLIP Preset Operating Temperature Humidity Dimension Weight RS485 External Control TRX TRX 2400bps 4800bps 9600bps 19200bps 38400bps and 57600bps selectable SAMSUNG TECHWIN PROTOCOL AVAILABLE PELCO D PROTOCOL AVAILABLE ON OFF 32Zones It consists of 8Group 4Programmable Zone per Screen Vertical Horizontal Vertical Horizontal OFF Selectable 8 Positions 10 C to 50 C 20 to 80 RH 0150 x 130mm H 1 4 kg SVD 4300WN SVD 4300WP Ivory color base model DECLARATION OF CONFORMITY Application of Council Directives 89 336 Manufacturer s Name SAMSUNG TECHWIN CO LTD Manufacturer s Address SAMSUNG TECHWIN CO LTD 42 SUNGJU DONG CHANGWON CITY KYUNGNAM KOREA 641 716 European Represen
18. q to confirm Increase or decrease optical zoom zoomyrocus pos serue ZOOM or digital zoom D ZOOM positions using the directional buttons while verifying A TELE WIDE lt NEAR gt 1 Press the SET button to access the setup manu and then position the the changes on screen Press the SET button Press SET to Return indicator over FOCUS using the UP or DOWN button once desired image quality is obtained Focus 2 Press the SET button can be manually adjusted independent of moving zoom OMODE You can select the most suitable zoom mode Move the arrow indicator to ZOOM You can select to use ZOOM Move the arrow indicator to ZOOM MODE using UP or DOWN button using UP or DOWN button Set ZOOM TRK to on using LEFT or RIGHT button b HODE AUTE ZOOM SPEED Configure zoom tracing speed using this feature Position the indicator over 700 SPEED using the UP or DOWN button and then set to e AUTO Select AUTO and press the SET button to confirm Increase or decrease desired mode using the LEFT or RIGHT button optical zoom ZOOM digital zoom D ZOOM positions using the UP or DOWN zoomyrocus serue button while verifying the changes on screen Enabling D ZOOM ON means that digital zoom will activate once optical zoom press ser to return ends Focus is automatically adjusted with E moving zoom 5 To move zoom
19. re Position the indicator over USER PRESET using the UP or DOWN button and then set to ON using the LEFT or RIGHT button Press the SET button to confirm PUSER PRESET OFF e PRESET NO Up to eight different preset configurations are supported PPRESET HO HO 1 e PRESET MODE Configure initial settings under FOCUS EXPOSURE etc USER PRESET MODE SETUP FOCUS EXPOSURE END e PRESET SAVE Save configured preset PPRESET SAUE e PRESET CLEAR Clear configured preset e GROUP SEL Choose up to eight groups Each group can consist of four mask eAREA SEL Configure eight mask areas e AREA MODE Mask area display m move the mask area up E e LEFT To move the mask area left RIGET areas e MASK TONE Adjust desired mask color level BOTTOM To move the mask area down E e RIGHT To move the mask area right END Revert to the SPECIAL SETUP menu DAY NIGHT Select from COLOR BW AUTO modes PORY HIGHT COLOR ACY Mask pri ing this f h k d e COLOR Color mode PRIVACY Mask privacy area using this feature The mask area expand contract upon the zoom position p e AUTO1 2 The camera automatically detects lighting conditions and selects the mode accordingly Auto 1 mode is switched to IR Cut Filter more lightning conditions than Auto 2 b PEIUBRCY 3 e When selecting AUTO2 mode the AGC is fixed at HIGH mode SYNC Two
20. s the SETUP button En i0 OFF MOTION DETECTION mode is cancelled END ON Any motion in the selected areas is observed ePlease select the area you wish to observe from the 4 areas in AREA SEL mode ePlease select ON mode for the chosen area ePlease adjust the size of the area to be observed by using the UP DOWN LEFT or RIGHT button ePlease press the SETUP button to save changes and complete the setting 3 Notes Tips on Using the Motion Detection Feature he feature may not function properly under flickering light conditions he camera interprets sudden changes in lighting and subsequent change in brightness of an object as motion e With the feature enabled other algorithms may require additional time to operate than usual his system does not guarantee prevention of fire or theft The manufacturer shall not be held responsible for any accident or damage incurred COLOR CCD CAMERA 23 User s Manual ONE PUSH Focus is automatically adjusted just once after zoom position is changed Select ZOOM FOCUS POS SETUP ONE PUSH and press the SET button to m wo confirm Increase or decrease optical lt iNEAR gt FAR zoom ZOOM or digital zoom D ZOOM press eta positions using the directional buttons _ O while verifying the changes on screen Press the SET button once desired image quality is obtained eMANUAL Select MANUAL and press the SET button
21. synchronization modes are available INTERNAL and EXTERNAL LINE LOCK In LINE LOCK mode it synchronizes the camera s video out signal to the external SYNC signal COMM RD Internal synchronization eLL External line lock synchronization choose LL you can adjust the desired phase Press the SET button You can adjust the desired phase from 0 to 359 e For NTSC models the line lock mode can be used if the external SYNC signal frequency is at 60Hz For PAL models the line lock mode can be used if the external SYNC signal frequency is at 50Hz ADI Use this feature to select communication commnrcarron serue protocol Position the indicator over DISP CAM ID ON COMMUNICATION using the UP or BAUD RATE DOWN button UART MODE Me RET PKT DISABLE e CAM ID Assign ID number to the camera It is restricted available to set ID from 0 to 255 e DISP CAM ID Displays camera ID on top left corner of the screen BAUD RATE Configure baud rate from 2400bps 4800bps 9600bps 19200bps 38400bps and 57600bps UART Configure parity bit to NONE EVEN or ODD Data bit is set to 8bit and stop bit to 1bit Set the UART MODE to EVEN if using the Remote Controller e RET PKT Used to transfer a packet e END IMAGE ADJ Includes image quality or special function EN m factors IMAGE SETUP e FREEZE Use this feature to freeze capture an b T image na
22. tative Name European Representative Address Equipment Type Environment CCTV Camera Model Name SVD 4300P WP Beginning Serial NO 58040001 Year of Manufacture 2008 12 01 Conformance to EN 50081 1 1992 EMC Directive 89 336 EEC and 92 31 EEC EN 50130 4 1996 We the undersigned hereby declare that the equipment specified above conforms to the above Directive s Manufacturer SAMSUNG TECHWIN CO LTD Legal Representative in Europe Signature Je 7 Gm Signature Full Name HAN SEUG KIM Full Name Position QUALITY CONTROL MANAGER Position Place CHANGWON KOREA Place Date 2008 12 01 Date
23. using the LEFT or RIGHT button e HIGH Wide range gain value adjustment e NORMAL Normal range fain value adjustment OFF Disabled SSNR Samsung Super Noise Reduction On screen noise reduction 1 Position the indicator over SSNR using the UP or DOWN button 2 Set SSNR to the desired mode using the LEFT or RIGHT button eLOW low noise reduction MIDDLE Medium noise reduction eHIGH High noise reduction eOFF Disabled e Changing setting from NORMAL to HIGH results in greater sensitivity as well as on screen noise e Setting AGC to OFF locks SSNR configuration SENS UP This feature ensures clear images at night or under low lighting conditions 1 Position the indicator over SENS UP using the UP or DOWN button 2 Set SENS UP to the desired mode using the LEFT or RIGHT button AUTO Select this mode for use in night time or under low lighting conditions eOFF Disabled b SENS UP e Once AUTO mode is set the user can configure Sens Up limit by increasing decreasing the shutter speed e g x2 x32 x64 X128 e Enabling Sens Up increases camera sensitivity and may result in additional noise and or other phenomenons This is normal 1 Press the SET button to access the main setup menu and then position the indicator over SPECIAL using the UP or DOWN button 2 Press the SET button to confirm USER PRESET Preset user designated configurations using this featu
24. wing conditions When the scene contains mostly high color temperature object such as a blue sky or sunset amp When the scene is dim If your camera directly faces a fluorescent lamp or is used in an environment of varying lighting conditions BACKLIGHT When there is a strong backlight behind the object clear images of the background as well as the object can still be obtained by using the BACKLIGHT function 1 Please position the arrow to point to BACKLIGHT on the SETUP menu by using the UP and DOWN buttons 2 Please select the mode you wish to operate by pressing the LEFT or RIGHT button BuUT Tap PumUT PLE LIR Lip ee pm ne Po HIGH MIDDLE LOW You can adjust the sensitivity of Backlight Compensation OFF BACKLIGHT function does not operate Backlight ON Backlight OFF COLOR CCD CAMERA 22 User s Manual MOTION DETECTION This product has a feature that allows you to observe movements of objects in 4 different areas on the screen and the words MOTION DETECTED appear on the screen when movement is detected hence a single individual can conduct supervision efficiently The camera detects an object s movement by sensing disparity of outline and level of brightness and color Please press the SETUP button MD SETUP OFF MOTION DETECTION mode is cancelled E ON Any motion in the selected areas is observed p DE ePlease pres
Download Pdf Manuals
Related Search