miface Ethernet / RS10
Contents
1. del eur a Power Supply DIP Switch 2 Ethernet DIP Switch 1 edel 12345 67 8 RS232 485 422 8 o o amp U EE BE RS232 485 422 Page 3 microSYST Systemelectronic GmbH Zur Centralwerkst tte 10 D 92637 Weiden Germany Phone 49 961 39166 0 Fax 49 961 39166 10 www microsyst de info microsyst de miface Eth ernet RS10 W nigo Universal Interface with Ethernet TCP IP Serial Interface RS232 485 422 3 Technical Data General Specifications Interface 1 Baud rate Interface 2 Baud rate Data format Parity Operating voltage Power consumption Housing Housing dimensions Mounting Protection Operating temperature Storage temperature Ethernet TCP UDP 10 100 MBaud RS232 485 422 selectable with DIP switches 300 Baud 115 kBaud 7 or 8 bits 1 or 2 stop bits odd no even 24 VDC 20 ca 150 mA at 24 VDC top hat rail housing with metal cover 100 x 87 x 45 mm 3 94 x 3 43 x 1 77 top hat rail 35 mm 1 38 DIN mounting rail front panel IP00 0 50 25 60 Page 4 microSYST Systemelectronic GmbH Zur Centralwerkst tte 10 D 92637 Weiden Germany Phone 49 961 39166 0 Fax 49 961 39166 10 www microsyst de info microsyst de miface Ethernet RS10 aise Universal Interface with Ethernet TCP IP Serial Interface RS232 485 422 3 1 Configuration of the Ethernet Interface The Ethernet interface must be configured before use IP addr2. Function Serial Port Channel 1 Status Serial Port Channel 2 Status Diagnostic Network Link Status Description Lights solid green to indicate Channel 1 is idle Blinks green to indicate Channel 1 is connected to the network and active Blinks or lights solid red in combination with LED 1 green to indicate diagnostics and error detection LED 3 red solid LED 1 green blinking 1x EPROM checksum error 2x RAM error Network controller error EEPROM checksum error Duplicated IP address on the network Software does not match hardware LED 3 red blinking LED 1 green blinking 4x Faulty network connection 5x No DHCP response received Lights solid green to indicate network port is connected to the network Normal state connection to channel 1 inactive LED 1 lights solid LED 2 off LED 3 off LED 4 lights solid Normal state connection to channel 1 active LED 1 blinking LED 2 off LED 3 off LED 4 lights solid Page 9 microSYST Systemelectronic GmbH Zur Centralwerkstatte 10 D 92637 Weiden Germany Phone 49 961 39166 0 Fax 49 961 39166 10 www microsyst de info microsyst de miface Ethernet RS10 aise Universal Interface with Ethernet TCP IP Serial Interface RS232 485 422 DIP Switch 1 2 DIP Switch 1 ARARARAR 5 IN DIP Switch 2 TEE According to the desired RS interface RS232 RS485 or RS422 the two DIP switches must be set as fo
3. page appears at which the setup for the RS inter face can be done Page 6 microSYST Systemelectronic GmbH Zur Centralwerkstatte 10 D 92637 Weiden Germany Phone 49 961 39166 0 Fax 49 961 39166 10 www microsyst de info microsyst de miface Ethernet RS10 aygo Universal Interface with Ethernet TCP IP Serial Interface RS232 485 422 4 Connector Pin Assignments la 1 LEDs Se mininin 321 1234 Power Supply DIP Switch2 Ethernet DIP Switch 1 elle 1234567 8 RS232 485 422 so 6 o o1 x 8 008 LJ PE Reset LEDs Ethernet e N U Page 7 microSYST Systemelectronic GmbH Zur Centralwerkst tte 10 D 92637 Weiden Germany Phone 49 961 39166 0 Fax 49 961 39166 10 www microsyst de info microsyst de miface Ethernet RS10 aise Universal Interface with Ethernet TCP IP Serial Interface RS232 485 422 Power Supply Pin Assignment Ethernet Pin Assignment nc 12345678nc I PE Bend upwards to connect Page 8 microSYST Systemelectronic GmbH Zur Centralwerkst tte 10 D 92637 Weiden Germany Phone 49 961 39166 0 Fax 49 961 39166 10 www microsyst de info microsyst de miface Ethernet RS10 aise Universal Interface with Ethernet TCP IP Serial Interface RS232 485 422 LEDs green 4 green
4. 4 a N 2 hd E PE E N Ke wellech 12345678 sx o o o 91 8 o o amp 400 L N E E LO A vr Top Hat Rail Mount Clip Fastener for 35 mm 1 38 inches DIN Rail microSYST Systemelectronic GmbH Zur Centralwerkstatte 10 D 92637 Weiden Germany Phone 49 961 39166 0 Fax 49 961 39166 10 www microsyst de info microsyst de micro SYST Page 12 miface Ethernet RS10 Gage Universal Interface with Ethernet TCP IP Serial Interface RS232 485 422 6 Appendix 6 1 Standard Equipment e Interface with current software and hardware versions e Users manual e Mating plug for power supply 6 2 Optional Accessories e Users manual e Mating plug for power supply e Mating plug for 9 Pin Sub Miniature Socket Connector Page 13 microSYST Systemelectronic GmbH Zur Centralwerkst tte 10 D 92637 Weiden Germany Phone 49 961 39166 0 Fax 49 961 39166 10 www microsyst de info microsyst de miface Ethernet RS10 micro Universal Interface with Ethernet TCP IP Serial Interface RS232 485 422 6 3 Declaration of Conformity Produktbezeichnung Product Hersteller Manufacturer miface FI Ethernet microSYST Systemelectronic GmbH Zur Centralwerkst tte 10 D 92637 Weiden Das bezeichnete Produkt stimmt mit der folgenden Europ ischen Richtlinie berein We herewith confirm that the above men tioned product meets the requirements of the following standard Die ber
5. einstimmung des bezeichneten Produktes mit den Vorschriften der Richtli nie wird nachgewiesen durch die vollst n dige Einhaltung folgender Normen The correspondance of the above mentioned product with these requirements is proved by the fact that these products meet with the fol lowing single standards Nummer Bezeichnung Europaische Norm Elektromagnetische EN61000 6 2 2005 89 336 EWG EN61000 6 4 2002 Vertraglichkeit EMV Weiden den 28 Marz 2007 O Silvan Hartw Gesch ftsf hrer Managing director Page 14 microSYST Systemelectronic GmbH Zur Centralwerkst tte 10 D 92637 Weiden Germany Phone 49 961 39166 0 Fax 49 961 39166 10 www microsyst de info microsyst de miface Ethernet RS10 aise Universal Interface with Ethernet TCP IP Serial Interface RS232 485 422 6 4 Guarantee The interface is guaranteed within the existing period of warranty against defects which existed at the time the device was delivered to the buyer The device is subject to technical change without notice Errors and omis sions are excepted No claims can be honoured for the shipment of a new product The buyer is required to make notification of defects within 2 weeks after identification of such Non observance of notification re quirements is equated with acceptance of the defect Defects and their symptoms must be described as accurately as possible in order to allow for reproducibility and eliminatio
6. ess net mask and port number settings Switch the supply power for the interface on and connect it to the net work hub with an RJ45 cable 1 1 cable or directly to a PC crosslink cable Start the MS DOS entry prompt at your Windows PC If there is a connection to the network e Make sure that at least one entry has been made to the PC s ARP table ARP A lt CR gt e If not make the following entry PING lt CR gt IP address of any desired network user Enter the desired IP address for the interface to the ARP table ARP S XXX XXX XXX XXX 00 20 4A xx xx xx lt CR gt XXX XXX XXX XXX desired IP address 00 20 4A xx xx xx Ethernet address of the interface see label at the bottom of the housing Make sure that the IP address of the interface is now included in the ARP table ARP A lt CR gt If not repeat the last two steps the pause between entering PING and ARP S must not be too long Establish a Telnet connection to port 1 TELNET XXX XXX XXX XXX 1 lt CR gt This connection will fail disconnect within 3 seconds However the IP address of the interface is temporarily changed Close the Telnet window after acknowledging the error message Page 5 microSYST Systemelectronic GmbH Zur Centralwerkstatte 10 D 92637 Weiden Germany Phone 49 961 39166 0 Fax 49 961 39166 10 www microsyst de info microsyst de miface Ethernet RS10 aise Universal Interface with Et
7. hernet TCP IP Serial Interface RS232 485 422 Establish a Telnet connection to port 9999 TELNET XXX XXX XXX XXX 9999 lt CR gt After the connection has been established immediately press the en ter key within 5 seconds in order to enter the setup mode Enter 0 server configuration Enter the desired IP address and press the enter key Repeatedly press the enter key until Netmask Number of Bits for Host Part appears Enter here the number of free bits for the IP address f e 8 for the netmask 255 255 255 0 11111111 11111111 11111111 00000000 or 11 for the netmask 255 255 248 0 11111111 11111111 11111000 00000000 and press the enter key Repeatedly press the enter key until Your choice appears Enter 1 channel 1 configuration Repeatedly press the enter key until Port No 10001 appears Enter the desired port number and press the enter key Repeatedly press the enter key until Your choice appears Press 9 to save all settings gt the Telnet connection is interrupted Configuration of the Ethernet interface is now complete From now on the control frame can be transmitted to the interface via the selected IP address and the selected port 3 2 Configuration of the RS Interface Start your web browser e g Netscape Navigator or Internet Explorer Input the recently set IP address see chapter 3 1 into the address field After ca 1 minute a HTML
8. llows RS232 DIP Switch 1 DIP Switch 2 Pin Pin 1 2 3 4 5 6 7 8 1 2 3 4 ON ON OFF OFF OFF OFF OFF OFF ON OFF OFF OFF RS485 DIP Switch 1 DIP Switch 2 Pin Pin 1 2 3 4 5 6 7 8 1 2 3 4 OFF OFF ON ION ION ION OFF OFF OFF ON OFF OFF RS422 DIP Switch 1 DIP Switch 2 Pin Pin 1 2 3 4 5 6 7 8 1 2 3 4 OFF OFF ON ION ION ION ON JON OFF ON ON OFF Page 10 microSYST Systemelectronic GmbH Zur Centralwerkst tte 10 D 92637 Weiden Germany Phone 49 961 39166 0 Fax 49 961 39166 10 www microsyst de info microsyst de miface Ethernet RS10 aise Universal Interface with Ethernet TCP IP Serial Interface RS232 485 422 9 Pin Sub Miniature Socket Connector RS interface According to the selected RS interface the following assignment is applicable RS232 Assignment Page 11 microSYST Systemelectronic GmbH Zur Centralwerkstatte 10 D 92637 Weiden Germany Phone 49 961 39166 0 Fax 49 961 39166 10 www microsyst de info microsyst de 5 Housing Dimensions miface Ethernet RS10 GG Universal Interface with Ethernet TCP IP Serial Interface RS232 485 422 x 100 mm 3 94 se ek 123
9. miface Ethernet RS10 Universal Interface with Ethernet TCP IP Serial Interface RS232 485 422 User s M FEMA ELECTRONICA S A microSYST Systemelectronic GmbH Zur Centralwerkstatte 10 D 92637 Weiden Germany Phone 49 961 39166 0 Fax 49 961 39166 10 www microsyst de info microsyst de miface Ethernet RS10 micro Universal Interface with Ethernet TCP IP Serial Interface RS232 485 422 Table of Contents 1 GENERAL 3 2 OVERVIEW 3 3 TECHNICAL DATA 4 3 1 Configuration of the Ethernet Interface 5 3 2 Configuration of the RS Interface 6 4 CONNECTOR PIN ASSIGNMENTS 7 5 HOUSING DIMENSIONS 12 6 APPENDIX 13 6 1 Standard Equipment 13 6 2 Optional Accessories 13 6 3 Declaration of Conformity 14 6 4 Guarantee 15 6 5 Versions Overview 16 Page 2 microSYST Systemelectronic GmbH Zur Centralwerkst tte 10 D 92637 Weiden Germany Phone 49 961 39166 0 Fax 49 961 39166 10 www microsyst de info microsyst de miface Ethernet RS10 aise Universal Interface with Ethernet TCP IP Serial Interface RS232 485 422 1 General With the help of the universal interface Ethernet frames are read out to the serial interface and frames received by the serial interface are trans mitted to the Ethernet DIP switches are included at the front panel for easy selection between RS232 RS485 or RS422 interface The device s mechanical design is intended for top hat rail mounting 2 Overview Ethernet
10. n The buyer must pro vide for access to all required and or useful information regarding defects at no charge as well as to the affected devices and must make all of the required data and machine time available free of charge The guarantee does not cover defects which result from non observance of the prescribed conditions of use or from improper handling If the device has been placed at the disposal of the buyer for test pur poses and has been purchased subsequent to such testing both parties agree that the product is to be considered used and that it has been pur chased as is No guarantee claims may be made in such cases The General Terms and Conditions regarding manufactured products and services rendered for the electrical industry apply as well Page 15 microSYST Systemelectronic GmbH Zur Centralwerkstatte 10 D 92637 Weiden Germany Phone 49 961 39166 0 Fax 49 961 39166 10 www microsyst de info microsyst de miface Ethernet RS10 aygo Universal Interface with Ethernet TCP IP Serial Interface RS232 485 422 6 5 Versions Overview 1 28 03 Kreuzer 5 5 03 Kreuzer Layout b 8 8 03 Kreuzer Layout X M22 5RS2EH 001 2 26 04 Kreuzer Ethernet Configuration changed 1 40 8 10 09 Kreuzer Baud rate 10 100 MBaud Certified per DIN EN ISO 9001 2008 Page 16 microSYST Systemelectronic GmbH Zur Centralwerkstatte 10 D 92637 Weiden Germany Phone 49 961 39166 0 Fax 49 961 39166 10 www microsys
11. t de info microsyst de
Download Pdf Manuals
Related Search