VSP 330 User Manual Version 1.1
Contents
1. RS232 interface RJ11 used to connect the computer 5 HDMIA input interface Input the signal from HD player DVD computer and so on 6 HDMIB input interface Input the signal from HD player DVD computer and so on 7 HDMI LOOP OUT used to loop input HDMI signal to next processor 8 11 HDMI1 4 HDMI output connector HDMI1 4 DVI I connector HDMI1 3 compatible 12 13 Switch and Power RARIK in VSP 330 Document ID RGB RD UM V330C001 1 2 0 Front Panel Operation Insert power cord and push power to ON position LCD module on the front panel will show RGBLINK and go into self verification before it load last setting configuration and send processed image to the target monitor For the first setup CV1 input is default source With front panel keyboard user can operate VSP with menu display on LCD module 1 LCD Module the menu to show the switching between bottons and transmission 2 Keyboard ESC Push to exit from current selected item SEL Push to confirm the current selected item UP Push to select item in up option DOWN Push to select item in down option LEFT Push to select left item RIGHT Push to select right item HDMIA Push to switch to HDMIA Input HDMIB Push to switch to HDMIB Input HDMI1 Push to HDMI1 output setting menu HDMI2 Push to HDMI2 output setting menu HDMI3 Push to HDMI3 output setting menu HDMI4 Push to HDMI4 output setting menu HDMI1 4 use standard DVI I connector w2. gt 1024 Scale A Height gt 68 With PIP Picture in Picture mode user can adjust X Y position of sub picture user can not adjust X Y position of the main picture POLK VSP 330 Document ID RGB RD UM V330C001 8 Scale B Pos X gt 0 Scale B Pos Y gt 0 Push LEFT RIGHT to set the value of coordinate X or Y Scale B Width gt 1024 Scale B Height gt 68 Push OUT to go into output formats menu push UP DOWN to find the right output resolution which user may use select LHDMIA The output format would be the same with HDMIA use HDMIB output format would be the same with HDMIB Output Format gt HDMIA Output Format gt HDMIB Push UP DOWN to find the resolution as shown Output Format gt 1024x768x60 Push PIP to enter picture in picture mode press this button to display the two video sources from HDMI1 and HDMI2 Setup PIP mode Finished The device supports total 6 user configuration modes when press SAVE button SAVE1 SAVE2 SAVE3 SAVE4 SAVE5 SAVE6 button will light up together and the menu will shows Save Setting To Press ESC to Exit Press SAVE1 to save the current configuration to User Mode 1 Save Setting To SAVE1 Finished After user mode 1 saved User Mode 1 will be recalled after the device power on User do not make factory reset before that Other user mode can be called if push the user mode RGBlink POLK
3. User can change the value of Output Width and Output Height inside EScaler after user change the value should push Set button to active And user can change the video size by plug image on the right Resolution f Windows Prolessional When user push AB button 8 will open page as following which is also inside Image Fun page but change from PIP to Alpha POL ik VSP 330 Document D RGB RD UM V330C001 21 system Statue Image Fun Scale Swap Mode CUT Switch F The opening function Switching Time ven e e F Alpha the equipment provide six seamless switching mode image right shift image moves left image moves down image upshifting and image fluctuation to move image center to center around move on both sides When opening transparent switch equipment provided with 6 kinds of seamless switching mode switch has a transparent soft change effect When closing transparent switch equipment provided with 6 kinds of seamless switching mode switch no transparent soft change effect fade in fade out time switch range from 0 5s to 30 0s Click the option PORTA PORTB or PORTB PORTA during the two video inputs switch user will find the effects they choose GOOD Auto Config If user push button VSP 330 will auto set the parameters which is the same function to the front panel Freeze button 5 2 Setup Communication by RS232 Use DB9 to RJ11 cable to control VSP 330 by
4. VSP 330 Document ID RGB RD UM V330C001 9 button separately Push HDMI1 LHDMIG 1 HDMI3 or HDMI4 to each output setting menu gt HDMI1 TP Setup XP Setup Push UP DOWN shows gt HDMI1 DE Setup Select TP Setup and push SEL to go into TEST Pattern setting menu TEST Pattern is used to test monitor and signal stability gt HDMI1 TP On Off ON Push UP DOWN to enable by ON or disable by Off of the TEST Pattern select ON and push SEL to enter into TEST Pattern the device offers following TEST Pattern Mode standard horizontal and vertical color bar horizontal and vertical gray scale left rolling bar right rolling bar up rolling bar and down rolling bar left incline rolling bar right incline rolling bar gt HDMI1 TP Mode gt Color Bar H Then push UP DOWN as follows gt HDMI1 gt Color Bar V Push UP DOWN as follows gt HDMI1 TP Mode gt Gray Bar H Push UP DOWN as follows gt HDMI1 TP Mode gt Gray Bar V Push UP DOWN as follows gt HDMI1 TP Mode gt Auto Color Push UP DOWN to go into Manual Color to change display color manually AGRIC in VSP 330 Document ID RGB RD UM V330C001 10 gt HDMI1 gt Manual Color Push SEL to go into Manual Color gt HDMI1 TP Color gt R 000 G 000 B 000 Push LEFT RIGHT to chose the parameters push UP DOWN toset the parameters Push
5. block 3 0s003000 0003FFF Erase block 4 0x004000 0x004F FF Erase block 5 O 005000 0 005F FF Erase all Flash Code Ad Prot Erase blocks used by Hex File Modified 40 A 21 2010 14 44 more info Step 4 Options step 5 Start Verify after programming Set Code Read Prot Fill unused Flash Gen block checksums Execute Download free 8051 and 4 code examples using 12C CAN Flash etc WIM Bsacadeny com fagi progs After download exit the program turn off the power push the two white coding switch back to default position Power on VSP 330 check whether VSP 330 works well as version control Flash Magic download website http reblink cn _d269804420 htm POL ik VSP 330 Document ID RGB RD UM V330C001 29
6. 1 Appendix I Download the IP software 1 First connect the device with PC by network cable B gt i PRAT ji i b bd 2 Input VSP 330 network address in address bar 192 168 0 100 enter the user name admin and password rgblink123 in the dialog box er SP SS0RIPHH HERRIE 192 165 0 100 Windows fut VSP330 Device Server TRR eS 192 168 0 100 HAPHE B T be LHD EH HH a TE AAA UE admin C iat ELD rablink123 3 Thirdly click on FPGA Upgrade POL ik VSP 330 Document ID RGB RD UM V330C001 26 eS http 192 168 0 100 0 D T Aot ib DU VSP330 server pages VSP330 Device Page L FPGA Upgrade Control Device Graph ADEA RA 4 Fourthly click on browse to select upgrade file name must be Preamp_FPGA bin or Bakamp_FPGA bin QO Le trsrsarssoso0 casect 8 6 XS rie upo VSP330 Device Page Upgrade FPGA You can select files from your local PC and upload them to FPGA Files will upgrade FPGA Mee KH X Preamp_FPGA bin 5k Select a File to upgrade FPGA Bakamp FPGA bin E ARM VSP330 FPGA Bakamp_FPGA bin Attention upgrade preamp FPGA file name is Preamp_FPGA bin Mc RIES TED upgrade bakamp FPGA file name is Bakamp_FPGA bin RGBlink Xiamen Corporation Ltd Click Send to send and wait for upgrade RGBlin al VSP 330 Document D RGB RD U
7. It is normal when check Video Input is used to check whether input signal from HDMIA or HDMIB is correct It is correct when checked DVID4P System Control There are two working modes for each output one is Normal mode to output video which processed from inputs Test Mode is used to output test pattern Output Control Register Normal Model Test Mode Straight function used to set each output as the same to the input The following in the pages are used to set each channel output video For example If user push Channel2 for Channel it means HDMI output video the same to HDMIZ2 If user check Straight means HDMI1 output normal video which distribute default by the software in VSP 330 Document ID RGB RD UM V330C001 18 Channel A Straight C 7 Channel O Channel L 7 Channel L 7 Channel4 N E Channel Straight Channel O Channel L 3 Channel3 O Channeld Channels Straight C 7 Channel L 7 Channel L 7 Channel3 L 1 Channeld Channel4 A Straight Channel 1 Channel 2 L Channel 3 O Channel 4 DVID4P Video Module This page is used to test now not comments to do any modification DVID4P DDR Module Only comments user to change the X Y position for each output to meet processed video area requirement Channel 1 Channel 2 gt ave a E me E Channel 3 Channel 4 lt ea RSS DVD4P Pattern This is the page used to set test pattern output for each o
8. M V330C001 27 VSP330 Device Page Upgrade FPGA You can select files from your local PC and upload them to FPGA Files will upgrade FPGA Select a File to upgrade FPGA Send SEAR RAD Upgrade Bakamp FPGA Success Attention upgrade preamp FPGA file name is Preamp_FPGA bin upgrade bakamp FPGA file name is Bakamp_FPGA bin RGBlink Xiamen Corporation Ltd 6 Upgrade Bakamp FPGA Success 6 2 Appendix II Download the IP software Turn off the power take the two coding switch to ON sate As below Connect one side of the RJ11 download line to the RS232 on the video processor and the conte H other side to be connected to the serial port on the PC in VSP 330 Document ID RGB RD UM V330C001 28 _ Flash Magi l l Double click Ss to run Flash Magic setting as following Firstly users can choose the right serial port set the baud rate to 115200 choose LPC2368 and to load the aim document hex document of IP board upgrading Secondly confirm the two option box by tick Very after programming l Fill unused Flash Erase all Flash Secunty Clks PF een beck ehe kame Erase blocks used by Hex File _ Execute Finally click the Start button i Flash Bazic HOH PEODUCTION USE ONLY File ISP Options Tools Help Go 2AB vES Y 7 Step 1 Communications Erase block U 0x000000 0000F FF Erase block 1 0x007000 0x001 FFF Erase block 2 Ox002000 0 002F FF Erase
9. MI 1 DE Width 35 gt HDMI1 DE Height gt 35 DE H Start Image horizontal position setting DE V Start Image vertical position setting DE Width Image width setting DE Height Image height setting AGRIC in VSP 330 Document ID RGB RD UM V330C001 12 4 0 Customer Quick Setup Guide 1 Turn off the device 2 According to project requirements connect the necessary inputs and outputs for the cascade of other DVI device use the cascade interface 3 Power on the device 4 Choose the output format 5 Choose AB push effect 6 Select input channel 7 Select work mode 8 Set size and position of every output POL ik VSP 330 Document ID RGB RD UM V330C001 13 5 0 PC control VSP 330 control software interface is as following ra ASAE 1 0 6 0 sige EHO as ER ta 9 njoj a z 2 gt DADE uane iMan 3 SIE m m m m an mm a Resolution LUIS RSH SARE Pattem SHIRI RAS DDR Oia WAA 2011 01 10 17 14 08 812 1 R 2011 01 10 17 14 08 812 4MRom x 2011 01 10 17 14 08 828 J R7 2011 01 10 17 14 08 828 4EMCUAR AS 2011 01 10 17 14 08 859 Dpo fy 2011 01 10 17 14 08 859 2 FAS 2011 01 10 17 14 08 9750997 2011 01 10 17 14 08 796 0 py a Q 2011 01 10 17 14 08 796 292 Rom F COM Opened VSP 330 WCU S 1 0 FFPGA DV 0 0 S 0 0 BFPGA DV 0 0 S 0 0 S 1234 5 1 Softwa
10. N 1234 Push CLEFT RIGHT button to select Recall push SEL to do a Factory Reset after successful the menu shows Reset Finished Push LUP LKDOWN button to select the sub menu users can select to use English as menu language and loop out for HDMIA or HDMIB gt VSP 330 Language Loop out Push LEFT RIGHT button to select the sub menu of language as follow Language Select gt English Push LEFT RIGHT button to select Loop out connection Push CLHDMIA or HDMIB button to get the video from loop out connector directly Loop out Select gt HDMI A Push UP DOWN button to select the sub menu to set timer gt VSP 330 Time Calendar Push SEL button to go into Timer setting RARIK Lin VSP 330 Document ID RGB RD UM V330C001 5 Time gt 00 00 20 Push LEFT RIGHT to activate the timer setting when the left line shows the character means hour is editable push UP DOWN to change the minute or second Time 00 00 20 Push SEL to enter Calendar setting The date is shown on the left hand side on the right shows the Day of the Week Calendar gt 2010 01 01 Sun Push LEFT RIGHT to activate date setting When there appears the flashing character on the left of the date current flashing parameter could be revised push UP DOWN to adjust the date Time 2010 01 01 Sun Push UP DOWN to enter the submenu AB Mode and Scale P
11. UP DOWN as follows gt HDMI1 TP Mode gt Roll Left Select Roll Left Roll Right Roll down Roll Up Roll Up Left or Roll Down Right Push SEL Ito set the rolling bar push UP DOWN to set background and foreground colors The device offers total 8 colors white yellow sky blue green pink red blue and black Here is an example select roll left gt HDMI1 TP Roll gt Yellow gt HDMI 1 gt Yellow gt HDMI 1 TP Fore gt Yellow Push UP DOWN as follows gt HDMI1 TP Mode gt Roll Right Push UP DOWN as follows gt HDMI 1 gt Roll Down Push UP DOWN as follows gt HDMI1 TP Mode gt Roll Up RARIK in VSP 330 Document ID RGB RD UM V330C001 11 Push UP DOWN as follows gt HDMI1 TP Mode gt Roll Up Left Push UP DOWN as follows gt HDMI1 TP Mode gt Roll Down Right Select XP Setup and press SEL to set horizontal position push LEFT RIGHT to adjust the parameter value gt HDMI1 T23 Push UP DOWN enter vertical position setting push LEFT RIGHT to adjust the parameter value gt HDMI 1 t25 Select DE Setup to adjust image offset push SEL DE image offset could be adjusted gt HDMI 1 DE On Off ON Select ON to go into DE setting menu push UP DOWN LEFT RIGHT toset the parameter value as follows gt HDMI1 DE H Start gt 35 gt HDMI 1 DE V Start gt 35 gt HD
12. WU USP Video Processor User Manual VSP 330 eee nnna hog a 8888896660 RGBlink Science amp Technology Co Ltd The pictures and data in the user manual are reference only check the real object CONTACT US gaput Headquarter S603 Welye Building Torch Hi Tech Industrial Development Zone Xiamen Fujian Province PR C Shenzhen office Room A05 Floor 4 Building 24 Industry factory Nanshan Science amp Technology Park Shenzhen Guangdong Province P R C Tel 86 592 5771197 Fax 86 592 5771202 E mail rgblinkcs gmail com http www rgblink com Revision 1 0 2010 12 31 0000 Released Lisa 1 1 2010 01 12 0001 Based on the user manual following information has been added Connectors and connectivity PC software instructions Setup Communication by RS232 Setup Communication by USB Download IP board software CONTENT LO e siel ei cle Connective an eee eenetinh EE tne l TTT and contol SIG Mal E E l 20 Front Panel Operaatio Misena a a uoenaeeaceueabecieneebeeceeeabeeaevenees 2 5 IA OME Mea e E R ae eens 4 AO CUSTOMer Quick SELUD Gud E snn ena rE E EN E E EA 13 5 0 PG COMUO oe ee ee ae ee 14 COADOR T ENE E 26 1 0 Connectors and connectivity 1 1 Interface and control signal L ro 1 Small white push button used only when upgrade the firmware NO Copper RJ45 used to connect the computer by 568B 568A twist pair CAT5 cable 3 USB interface used to connect to the computer
13. ess switch effects for switch between HDMIA and HDMIB inputs Image Split Drawing shows the split images mode when the split button push Resolution User can save or delete all the operation log 2009 8 1 17 28 05 TOVC020000008101 00000082 ike SiR 2009 8 1 17 28 05 FRVCO601 060000 2009 8 1 17 28 05 TOVCO200000081 0500000086 fe 56E 2009 8 1 17 28 05 FRVCO601 C0601 320000 2009 8 1 17 28 05 TOVCO2Z00000081 0700000088 REFERRE aa 17 28 06 FRVCO601 000000 Information At the bottom of the software will show the model of the processor here ise VSP 330 the software version front firmware version back firmware version and serial number of the processor COM1 Opened VSP 330 MCU S 1 0 FFPGA D 0 0 S 0 0 BFPGA DV 0 0 S 0 0 SN 1234 POL ik VSP 330 Document D RGB RD UM V330C001 17 There are two system function pages one is DVID4P which used to set function on split mode GOOD page is used to set advance function like PIP seamless switch effects and so on DVID4P System Status Page User can check current split mode and system status DDR Module Pattern Screen Mode curent Screen Mode isn dE System Statue ODR Initialization _ Video Input The Screen Mode is used for the user to check which split mode current VSP 330 works The System Status has two status one is DDR initialization which is used to check whether VSP 330 hardware is working in normal status
14. hich is compatible with HDMI 1 3 use HDMI to DVI cable to connect with HDMI source SAVE1 Switch to active user defined model SAVE2 Switch to active user defined modez2 SAVE3 Switch to active user defined mode3 SAVE4 Switch to active user defined mode4 SAVE5 Switch to active user defined mode5 POLK VSP 330 Document ID RGB RD UM V330C001 2 SAVE6 Switch to active user defined mode AB Push to active seamless switch effects setting menu SCALE Push to active HDMIA and HDMI scale setting menu FRE Push to freeze the video from live or live the video from freeze MENU Push to go to main menu INF Push to check the menu of input and output info version and seriel NO OUT Push to active output format menu I II Push to set single picture mode or dual picture mode SAVE Push to go to save ready mode and then push SAVE1 SAVEZ SAVE3 SAVEZ SAVES or SAVE6 seperately will save the configuration Press Through mode VSP 330 works in distribution mode Press U Split input in Horizontal direction by zoom in input to 2 times HDMI1 output is the same to HDMI3 and HDMI2 output is the same to HDMI 4 Press SS Split input in Vertical direction by zoom in input to 2 times HDMI1 output is the same to HDMI3 and HDMI2 output is the same to HDMI 4 Press SS Split input in horizontal and vertical together with each 2 times which means each output 1 4 of the original input Press LT Split input in Horizontal directi
15. its RS 232 port DB9 should connect to PC com port or another device which has the com port RJ11 port should connect to RS 232 port on VSP 330 As shown of the following picture RERIN in VSP 330 Document ID RGB RD UM V330C001 22 ka a r ACIOOMOVDAS o A A ayy faan G i E fit After user get the right RS 232 port open communication setting page by push button under Communication part and the following dialog will be opened erial CommPort COM Baud ate 115200 O Ethernet Local Fort 1000 Remote Host 192 167 171 105 Remote Port UUU User should use the same CommPort to the PC or the control device in used and use Baudrate as 115200 After that push OK to close the dialog Push to setup communication with VSP 330 and will change to push will close the communication and will change back to which is ready for setup communication again See ae COM1 Opened After success of setting up communication it will show comt Opened and will change to green If user could not success to make communication should check whether the com part took place by another software RERIN in VSP 330 Document ID RGB RD UM V330C001 23 5 3 How to use a USB connection PC 1 Install the driver Connect USB cable to VSP 330 another end to PC or laptop power on VSP 330 For the first time to use the PC or laptop for VSP 330 it will ask for install the driver as followi
16. ng AB EF lS RO AAR AF C ha a TIRI RR BH E E Keil MCB2300 YCOM C MREHBHEARS CH RRA MEK Qe AA RAZ EFA BSE GE D FAE L T Choose from the list or the location of the USB driver click next to continue RAA MEHIS TL E DIED A THI TEIR ba s O ER ERI E LEER ESRF S a RH TSTS HERAT RRR BITE HLS TURI STR SK El SHE E FERAL Sah GH CD ROM 7 EES PRBS NEE 01 F ARGBLINK OLED DEV usb driver OFBER KE ACKRRE REF O REE MEME M PURE PERRIER Windows A REPRISE ATER ISR shiz Fr Sea ie tie LBC EAS MEHIS ASEARERE WAR F MCE2300 USB VCom Port i usbser sys S C WINDOWS system32 DRIVERS CTD wl VSP 330 Document D RGB RD UM V330C001 24 TEAS HE Ft lS TREA EPE a ST SS ESE esc T PAU SA E F MCE2300 USB VC an Port i SMS HBG W a After install is finished user will find the PC detect this USB device and will allocate a COM port the USB User can find this port inside device management of the system which show as MCB2300 USB VCom port O RRE L E THE Ew Aw Bea S e mg SR 1115 eh DVD CD ROM 3RSHSS IDE ATASATAPI 5159 ae VLS mee EGER SS 59 th RD com 390 LPT T PY MCE2300 USB VCom Port OMA da ARRE B T YT BRR ERS ERT annig Y 29 ESSERE gh PRES SECS 4 RES 0 9 Rak Setup with USB communication is the same to RS 232 POL ik VSP 330 Document ID RGB RD UM V330C001 25 6 0 Appendix 6
17. on by zoom in input to 4 times which means each output 1 4 of the original input Press Split input in Vertical direction by zoom in input to 4 times which means each output 1 4 of the original input POLK VSP 330 Document ID RGB RD UM V330C001 3 3 0 VSP 330 Menu After initial system menu will show as following RGBLINK HU LIT ERII AVDSP Series VSP 330 Wait Init Network User can connect the device with LAN Network If there is connection VSP 330 will get a auto allocated IP address directly IP Address 192 168 1 100 If there is no connection display will show DHCP Failed DHCP Failed Push MENU button to access the main menu as follow gt VSP 330 Dev Info Recall Touch LEFT RIGHT button to select the left or right menu items Before the menu item if there is a sign means the menu item has been selected you can push the SEL key to enter its sub menu in Dev Info menu Select it to show the information bout the input signal Short Cut Push the INF button to get the Dev Info As following HDMI A 0X480X0 HDMI B 0X480X0 Push UP DOWN to check the current format RARIK in VSP 330 Document ID RGB RD UM V330C001 4 Output Format 1024x768x60 Push UP DOWN to check the current version Software Version 1 0 Push UP DOWN to get the serial number user can get more service and support with the serial number RGBLINK S
18. re Introduce Language Option 2 Language The software supports Chinese and English version with language selected Communication Open COM U Close COM Device toolbar Synchronization Lin VSP 330 Document ID RGB RD UM V330C001 14 Click Synchronization Can sync the data from the VSP 330 in H Communication to the software run on the PC at the same time the data in the EPROM can synchronize with the device gt Save to flash Load from flash There are 6 user save modes ba Factory reset Click Factory setup previously saved user mode will be cleared al Advance for administrator control x POU Advance for engineer specially please contact with our Customer Service engineer to get the code if it is necessary Help Display helps dialogue About g Display the software version and company information is Output resolution User can choose different output resolution by selecting from pull down list Click the drop down arrow to select HDMIA or HDMIB then the output resolution is the same to them seperately AGRIC WIR VSP 330 Document ID RGB RD UM V330C001 L5 in E 2 12805720060 1280720060 12804102460 HDMI resolution show the current HDMIA and HDMIB input resolution info HDMI 4433 Port4 1024276860 PortB 1024 768 60 Split mode of VSP 330 1 El l Through mode VSP 330 works in distribution mode Each output is the same
19. to current input mode 2 al Split input in horizontal and vertical together with each 2 times which means each output 1 4 of the original input 3 mj Split input in Horizontal direction by zoom in input to 2 times HDMI1 output is the same to HDMI3 and HDMI2 output is the same to HDMI 4 4 al Split input in Vertical direction by zoom in input to 2 times HDMI output is the same to HDMI3 and HDMI2 output is the same to HDMI 4 5 mj Split input in Horizontal direction by zoom in input to 4 times which means each output 1 4 of the original input 6 Split input in Vertical direction by zoom in input to 4 times which means each output 1 4 of the original input 7 uj Split input in up 1 2 Horizontal direction by zoom in input to 4 times which means each output 1 8 of the original input 8 m Split input in down 1 2 Horizontal direction by zoom in input to 4 times which means each output 1 8 of the original input wl VSP 330 Document ID RGB RD UM V330C001 16 9 aj Split input in left 1 2 Vertical direction by zoom in input to 4 times which means each output 1 8 of the original input io El Split input in right 1 2 Vertical direction by zoom in input to 4 times which means each output 1 8 of the original input Mode 7 10 only can be active by software PIP Toolbar B PIP mode Defaultly HDMIA is main picture HDMIB input is sub picture Seamless switch effects Click this button to set seaml
20. ush the AB button to enter seamless switch effects setting gt VSP 330 Scale AB Mode AB Mode including full screen switching transparent full screen switch wipe off switch and so on Push LEFT J RIGHT to select AB Mode all available mode including CUT Switch Wipe right shift Wipe left shift Wipe up shift and Wipe down shift Setup AB Mode gt CUT Switch Setup AB Mode gt DISSOVLE Switch Push SEL to set fade in fade out duration time press L UD 1 LU DOWN to set seconds which ranges from 0 5 s to 30 0 s RARIK Lin VSP 330 Document ID RGB RD UM V330C001 6 Dissolve Duration gt 3 05 Push SEL to confirm enter into WIPE HARD Switch Setup AB Mode gt WIPE HARD Switch Setup AB Mode gt WIPE SOFT Switch Push UP DOWN there are several seamless switching modes as following WIPE Mode gt WIPE RIGHT WIPE Mode WIPE LEFT WIPE Mode x WIPE DOWN WIPE Mode x WIPE UP WIPE Mode x WIPE PLUS OUT WIPE Mode x WIPE CURTAIN OUT WIPE Mode x WIPE CENTER OUT Wink VSP 330 Document ID RGB RD UM V330C001 7 WIPE RIGHT SOFT WIPE RIGHT HARD W M WIPE LEFT SOFT WIPE LEFT HARD n m WIPE UP SOFT WIPE UP HARD an WIPE DOWN SOFT WIPE DOWN HARD d WIPE CENTER IN SOFT WIPE CENTER IN HARD H H WIPE CENTER OUT SOFT WIPE CENTER OUT HARD t WIPE PLUS OUT SOFT WIPE PLUS OUT HARD vas Push SCALE to go into SCALE MENU Scale A Width
21. utput user check Pattern 1 means user will control HDMI1 output as test pattern And Pattern2 is for HDMIZ2 Pattern 3 is for HDMI 3 and Pattern 4 is for HDMI4 _ Pattern 1 _ Pattern 2 _ Pattern 3 l T Pattern 4 When user check the Pattern 1 to Pattern 4 the following page will be opened at the same time in VSP 330 Document ID RGB RD UM V330C001 19 Pattern 1 Pattern 2 Pattern 3 TF kode Color Bar H User can select TP Mode such as Color Bar H from the list and then the each output will output test pattern Good Page When user want to use advance function of VSP 330 can push button under GOOD block When user push PIP button E the page will be opened as following GOOD PIP D IDAP System Statue VWideoPorts Video Module Fort B User can change the X Y position of the video from HDMIB input And user can push Scale page to set video size of HDMIA and HDMIB wl VSP 330 Document ID RGB RD UM V330C001 20 System Statue WideoPorts Image Fun Video Module Scale video width 11024 Ey video Height 768 EH EScaler Output Width 164 LZ Output Height 480 EH Video Width 1024 HH Video Height 768 Ss E Scaler Output width 400 H Output Height 300 HH For the parameters Video Width and Video Height inside ScaleA and ScaleB they are used for further function it is not use to change the value now Scale Video Width 1024 E P e l Video Height
Download Pdf Manuals
Related Search