LT-32HA48U LT-39HG48U
Contents
1. Select Auto if vou want the TV to acguire and enter the needed IP address automatically Select Manual if you want to enter your IP address manually then e Press Y to go to the first entry field e Enter the IP address Subnet mask Default gateway Primary DNS and Secondary DNS values Use the alphanumeric buttons to enter numbers and the arrow buttons to move from one entry field to another Once Auto or Manual IP setting is completed press MENU to go back press A Y to select Connection test then press OK P to check the Internet connectivity again Other information Password in Parental Control The default password is 1234 You can change it to a new one The super password is 0423 If you forget your code enter the super password to override any existing codes OSS Notice This product uses software library from Freetype Project This product uses software library which is distributed under the zlib license This product uses UNICODE software programmes which are distributed under IBM Open source license This product uses glibc software programmes which are distributed under the GNU license EN 15 ae Other information Z Chapter 7 Troublesk ooting and Help Line Troubleshooti d Help Li v roubleshooting and Help Line z A check through the guide below could save vou the trouble of returning your purchase or waiting for a service engineer If you still require assistanc2. Ensure that your domestic mains supply voltage matches the voltage indicated on the rating label located at the back of your set Where the mains plug or an appliance coupler is used as disconnect device it shall remain readily operable On certain models the light indicator is located at the side of the TV set The absence of a light indication at the front does not mean that the TV set is fully disconnected from the mains To disconnect the TV set completely the mains plug must be pulled out The TV set s components are sensitive to heat The maximum ambient temperature should not exceed 35 Celsius Do not cover the vents at the back or sides of the TV set Leave sufficient space around it to allow adequate ventilation Install the appliance away from any source of heat fireplace etc or appliances creating strong magnetic or electric fields Moisture in rooms where the set is installed should not exceed 80 humidity Moving the set from a cold place to a warm one can cause condensation on the screen and on some components inside the TV set Let the condensation evaporate before switching the TV set on again WARNINGS This appliance is intended for domestic household use only and should not be used for any other application such as for non domestic use or in a commercial environment If the supply cord is damaged it must be replaced by the manufacturer its service agent or similarly qualified persons in order to avoid a ha
3. child or keyboard lock is switched on if fitted EN 18 Check the power switches on the television and at the power outlet Check power is present at the outlet Check the fuse or circuit breaker at your main fuse box Look for a possible cause of failure before you replace or re set it Switch off main power and wait five minutes before trying again Leave the TV unplugged and call a service engineer if this does not work Please see relevant section of user instruction Chapter 8 ae Specifications Specifications for LT 32HA48U K Hro idans m Analogue PALINTSC SECAM M BIG I D K L L g Digital DVB T C S lt 0 3W A ON mode 30W Max 70W iciency Class A Annual energy 44kWh annum Headphone type Impedance 32 ohms or more with 3 5mm stereo jack plug Analogue 47MHz 866MHz Receiving channels Digital DVB T C 107 5MHz 858MHz LED Edge Panel Ratio 16 9 Resolution HD 1366 pixel horizontal x 768 pixel vertical Recommended PC VGA 1024x768 60Hz resolution HDMI 1360x768 60Hz Photo JPEG Music MP3 Video AVI MP4 PS TS RF in Scart VGA YPBPR video audio SPDIF USBx1 HDMIx2 Connections Headphone LAN DENON With stand W 733 4 H 504 D 183 millimetres Without stand W 733 4 H 452 D 64 5 millimetres With stand 8 3 kg Approximate welgnt Without stand 6 7 kg Remote control unit with 2 x batteries instruction booklet Power cord table top stand stand neck 7 x stand screws
4. 3 Turn on the TV and wait for the common interface function to be activated This may take several minutes Note Do not remove the common interface module from the slot Removing the module will deactivate the digital services Accessing common interface services EN O Oging more of your TV mon interface ntrol and select A Q After inserting and activating th module press Menu on the remo Options gt Common interface This menu option is only available if the mon interface module is correctly inserted and a tivated On screen applications and content are proviers A your digital TV service operator Software update Press Menu on the remote control and select K Options gt Software update Press OK p gt to enter Options Subtitle SPDIF type O amp O SPDIF delay T Link Common interface Home West EUR Enter Location Select Decoding page language Back Digital teletext language English Exit Software update Ethernet network Current version Checks the current version of the software Product name Displays the product name of your set Serial number if available Displays the serial number of your set OAD Over Air Download Enables you to install the latest version of the software if available Select OAD and press OK gt to enter e Use lt gt to select Yes under Auto download to automatically download the latest software if available After the softwa
5. Headphone LAN Dimensions With stand W 891 6 H 593 2 D 229 5 millimetres Without stand W 891 6 H 534 1 D 45 7 millimetres With stand 13 15 kg Approximate ve Oni Without stand 11 kg Remote control unit with 2 x batteries instruction booklet Power cord table top stand stand neck Accessories 8 x stand screws 1X stand spacer Safety instruction sheet Warranty card Stand installation guide Buckle use sheet Conversion Cable x3 Scart adaptor CMP adaptor Audio in adaptor Basta Conine Temperature 5 C 35 C 41 F 95 F P g Humidity 20 80 non condensing 7 Temperature 15 C 45 C 5 F 113 F ala Humidity 10 90 non condensing Energy consumption per year based on the power consumption of the television operating 4 hours per day for 365 days The actual energy consumption will depend on how the television is used USB supported file formats EN 20 We apologise or any Inconvenience caused by minor inconsistencies in these instructions which may occur as a result of product development JVC Kesa Electricals UK EC1N 6TE 26 08 2013
6. Menu to display the main menu Options Source 2 Press A V lt b gt to select the desired item then press OK to open the corresponding submenu 3 In submenus use A Y to select menu options use lt gt to set functions or change values Use OK to activate a setting Use OK p gt to open the corresponding submenu Press Menu to return to the previous menu 5 Press Exit to close the menu Note Some options may not be available for certain signal sources gt Selecting menu language You can choose your preferred menu language following the instructions below 1 Press Menu to display the main menu 2 Press A V lt D gt to select Setup then press OK to enter 3 Select Language and press OK gt to enter 4 Select Menu language and press lt P gt to select your desired language to display the menus 5 Press Exit to close the menu Using more of your TV Setting up your favourite channels You can create a list of your favourite TV channels 1 Press LIST 2 Press the yellow button to enter Channel list selection Press A Y to select the favourite list and press OK to enter Press the blue button to start editing your favourite list Press A Y to scroll through the channel list and press OK to select or deselect it 4 Repeat this procedure to setup other favourite channels 5 Press LIST Exit to exit ECO settings 1 Press Menu on the remote control and select Picture gt ECO settings p
7. do not match the monitors VGA or HDMI input specifications Change the refresh rate or resolution settings on the digital equipment if possible Some other equipment is using the same Put other equipment on stand by to see if frequency the interference stops change the output Picture interference like frequency of the equipment that is causing wavy lines or patterns Poor quality cable in the path between linterference see its instructions Sound interference may the TV and the TV aerial also be present Get higher quality cable Your aerial system is receiving an unwanted signal on the same frequency Get your aerial system checked Jumbled teletext characters Poor quality signal As for Snowy picture and Ghosts When RGB input is used there is a distorted picture Synchronisation signal is missing or no picture Press the AV button to select the AV input which receives the synchronisation signal EN 16 i c and Help Line Digital Terrestrial TV Picture blocking or freezing Sound breaking Up Some channels are missing Weak signal or wrong type of aerial Not receiving one or more digital multiplex freguencies Interference or other problem caused by passing aerial signal through other eguipment Try re tuning ley Aerial may not be suitable for digital TV Z broadcasts You may be in a place which does not get a good digital TV signal Get an aerial rigger to check the ae
8. press OK P to enter the next step 2 Press A V to select your country then press OK P to enter the next step Note If you select France you will have to enter the Password setting menu here in order to set a password Use the numeric buttons to enter a four digit number for your password Your password cannot be 0000 Re enter the same code to confirm the password After that you will enter the next step automatically In this step you can only press lt to return to the previous step 3 Press A V to select your tuner mode S Antenna or 2 Cable Select Antenna e Press OK P to enter e Press A V to select Scan then press OK gt to start the automatic search for all DVB T digital and or analogue channels Select 2 Cable e Press OK P to enter e Press A V to select Scan then press OK gt to directly start your initial setup or enter below step e Select Full if available to search for and store all DVB C digital and analogue channels e You may select another advanced scan EN O Installing channels mode if available for Si ple Advanced then configure the noe le information as described below Use the umeric buttons to adjust the values for frequency symbol rate and network ID use lt P gt to Stlect a modulation mode o e Press OK to start initial setup relating t amp l DVB C digital and analogue channels 0 Note To prevent the channel setup process from Sy being interr
9. recording will stop automatically A V lt b gt to adjust the recording duration Note If you change channels while recording a programme a prompt will appear on screen asking you whether you want to confirm the channel change If you do so your recording will be interrupted In recording PVR mini pane will also show on the screen to indicate the recording progress To watch the recorded programme exit PVR mode first and go to Media center gt Video Select the folder PVR then select the related record file Press OK to play It is the same if you record a digital radio programme Notes Feature available only for digital non encrypted channels Even when CICAM CI or CI is inserted feature is not available on encrypted channels Only supports USB memory device of FAT32 format Before you connect the USB device to the set make sure you have backed up the data in the device to avoid the loss of your important data due to unforeseen malfunction The bigger the USB device memory size for the PVR function the longer the recording time If you want to change channel or signal source during recording store the recording data before changing the channel or source The set cannot play files normally if the parameters of the file exceed the limitations of the system the file format is not supported the file is damaged or the file cannot be decoded Do not disconnect the USB memory dev
10. schedule select it and press OK to enter and follow the instructions on screen 7 Press Exit to close the menu Network connection This function is available only for CI modules with LSC function For detailed description please contact service provider or refer to instruction book provided by service provider Connecting to a wired network You can attach your TV to your LAN using cable in three ways e You can attach your TV to your LAN by connecting the LAN port on your TV to an external modem using a Cat 5 cable e You can attach your TV to your LAN by connecting the LAN port on your TV to an IP Sharer which is connected to an external modem Use Cat 5 cable for the connection e Depending on how your network is configured you may be able to attach your TV to your LAN by connecting the LAN port on your TV directly to a network wall outlet using a Cat 5 cable Note that the wall outlet is attached to a modem or router elsewhere in your house 1 Press MENU on the remote control and select Options gt Ethernet network gt Configuration gt Internet connection Press lt gt to select On 2 Press A Y to select Connection test then press 14 Chapter 6 OK to check the Internet connectivity If it does not work follow step 3 below 3 Select Options gt Ethernet network gt Configuration gt IP setting then press OK p gt to enter the IP setting menu You can set Address type to Auto or Manual
11. select Channel install and press OK p gt to enter Channel install Automatic search i ET ane Ot Automatic update Analogue manual scan Antenna manual installation Enter Select Back Exit On Chapter 4 amp 5 e Select Automatic search then press OK gt to display Automatic search e Press OK to skip the country selection and enter the next step Or use lt gt to reselect your country then press OK to enter e Select Digital amp Analogue Digital or Analogue then press OK b gt to start the automatic search which relates to all DVB T digital and or analogue channels Select Cable e Press A F to select Channel install and press OK p gt to enter e Select Automatic search then press OK p gt to display Automatic search e Press OK to skip the country selection and enter the next step Or use lt gt to reselect your country then press OK to enter Select Digital amp Analogue then press OK gt to enter Select your scan mode if available and configure proper cable information in the same way as in Initial setup Select Scan and press OK gt to start your automatic search relating to all DVB C digital and analogue channels Select Digital then follow the same process as above to start your automatic search relating to all DVB C digital channels Select Analogue then press OK gt to start your automatic search relating to all analogue channels 4 The search may ta
12. 1X stand spacer Accessories 2 x bracket screws optional screws for VESA bracket assembly Safety instruction sheet Warranty card Stand installation guide Buckle use sheet Conversion Cable x3 Scart adaptor CMP adaptor Audio in adaptor dasna Condones Temperature 5 C 35 C 41 F 95 F p g Humidity 20 80 non condensing S Temperature 15 C 45 C 5 F 113 F Stored O Nej cs Humidity 10 90 non condensing Energy consumption per year based on the power consumption of the television operating 4 hours per day for 365 days The actual energy consumption will depend on how the television is used USB supported file formats EN 19 ae Specifications E Specifications for LT 39HG48U Ka Froadeas l Analogue PAL NTSC SECAM M B G I D K L L g Digital DVB T C A Sound system FM Nicam Digital Wide Stereo on Input AC220V 240V 50HZ o Bewarconsumbtion Standby lt 0 3W ON mode 44W Max 85W p Efficiency Class At Annual energy 65kWh annum Sound output power 2 x 8 watts Headphone type Impedance 32 ohms or more with 3 5mm stereo jack plug Analogue 45MHz 866MHz Receiving channels Digital DVB T C 107 5MHz 858MHz LED Edge Panel Ratio 16 9 Resolution FHD 1920 pixel horizontal x 1080 pixel vertical Recommended PC VGA 1024x768 60Hz resolution HDMI 1920x1080 60Hz Photo JPEG Music MP3 Video AVI MP4 PS TS RF in Scart VGA YPBPR video audio SPDIF USBx1 HDMIx2 Connections
13. 3 for long time otherwise the TV screen may be damaged permanently OK To open the corresponding submenu and activate a setting in menus to freeze unfreeze the picture in digital TV mode Option Retum Option To display the function menu to perform certain operations to display the Teletext page in different modes Return To return to the previous channel to return to the previous menu in USB function V To control the volume E uS Info To display programme information if available Mute To switch the sound off and back on again P To change channels TEXT To toggle Teletext or Mix mode on or off SUBTITLE To select a subtitle language available for selected digital TV programme LIST To display channel list TV To access TV mode Colour To select tasks or Teletext pages see footnote The red button can also be buttons used for MHEG function Lang To select a sound type available for selected analogue TV programme to select an audio language available for selected digital TV programme TEXT SUBTITLE LIST Footnote Red green blue and yellow buttons are multi function please follow on screen prompts and section instructions EN 6 Ly A Getting started If the batteries in your remote control are run down you can use the buttons on your TV S In TV mode they have the same functions as the corresponding buttons on the remote control The OK on on the TV set can be pressed repeatedly to select the required sour
14. 6 Performing an automatic channel search 8 Chapter 8 Specifications cccsceeeeeeees 19 Chapter 4 Using your TV osrrononnnnnnn 9 Accessing channels c ccccceeeneeseeeeeeeneeenees 9 Watching connected devices cce cece eee e ees 9 OUTS za oskia cus saidno s li nonce i nn 9 Using TV menus asos zd s logo dula nr od 9 Selecting menu language o ooo none 9 Chapter 5 Using more of your TV 9 Setting up your favourite channels 9 ECO Settings neaei EEA NEREKTE SAE 10 Audio description zniass saikossnvov kko sirku k vo RAK 10 Using subtitles veveidaadeneece ties cee tween acebevadeace 10 Turning on off subtitles ccceccese ener ee eens 10 O Chapter 1 ae Connections Q Connecting the power and antenna To To switch on TV after connecting power cord press Q Note Position of power socket varies according to TV model On certain models you have to turgn the power switch first D b Cable e Cable 1 6 For LT 39HG48U For LT 32HA48U DVD recorder cable receiver Note Disconnect the power cord before connecting devices Note this TV set is not compatible with DLNA Digital Living Network Alliance AV CMP YPbPr AUDIO i Ant a Cabl LAN HDMI 1
15. ARC VGA adapter adapter adapter input i F a i i CH i nt L l a ta 1 DVD recorder Set top box Cable EN 4 O KA Connections Q DVD player home theatre system PC headphones To Notes W Before connecting a PC set the PC monitor refresh rate to 60Hz b The connectors of VGA and CMP YPbPr share the same audio input connector an Excessive sound pressure from earphones and headphones can cause hearing loss b It is recommended to use as short as possible high quality HDMI cables to avoid possible interferen amp It is recommended to use 1m long or shorter VGA cable with ferrites in case VGA input is available in Win and TV is connected using VGA cable Maximum supported VGA resolution is 1920x1080 60Hz O G 6 i g 9 AV CMP YPbPr AUDIO in Antenna Cable LAN HDMI 1 ARC VGA adapter adapter adapter input Q 7 A t LM i i i AI 4 tt i DVD player Home theatre system Blu ray Disc player HD game console amp HD camcorder Notes ARC Audio Return Channel function is only supported on HDMI 1 ARC port Number of HDMI may vary USB connector is for data input from USB storage devices All USB devices have to be directly connected to TV set w o cable extenders In case extender is required it has to be as short as possible and equipped with ferrites HD game console HD Camcorde
16. JVC 4 EDGE LED TV LT 32HA48U LT 39HG48U i User manual Gebruikshandleiding Guide d utilisation Navod na pouzitie Manual de usuario Manuale d uso N vod k pou it O 00000 0000 e 00000 000 000 c Home DOLBY HD piaia video HIGH DEFINITION MULTIMEDIA INTERFACE DIG ITAL PLUS 1080p LT 32HA48U LT 39HG48U f Manufactured under license from Dolby and the double D symbol are trademarks of Dolby Laboratories This product is protected by certain intellectual property rights of Microsoft The HD TV Logo and 1080p qualifier Logo are trademarks of DIGITALEUROPE DVB and the DVB logos are trademarks of the DVB project THIS PRODUCT IS LICENSED UNDER THE AVC PATENT PORTFOLIO LICENSE FOR THE PERSONAL USE OF A CONSUMER OR OTHER USES IN WHICH IT DOES NOT RECEIVE REMUNERATION TO i ENCODE VIDEO IN COMPLIANCE WITH THE AVC STANDARD AVC VIDEO AND OR ii DECODE AVC VIDEO THAT WAS ENCODED BY A CONSUMER ENGAGED INA PERSONAL ACTIVITY AND OR WAS OBTAINED FROMA VIDEO PROVIDER LICENSED TO PROVIDE AVC VIDEO NO LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY OTHER USE ADDITIONAL INFORMATION MAY BE OBTAINED FROM MPEG LA L L C SEE HTTP WWW MPEGLA COM HDMI the HDMI Logo and High Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries Important information Safety
17. Option button on the remote control Using one touch play With one touch play pressing the play button on for example your DVD remote control starts playback on your DVD device and automatically switches your TV to the correct source displaying DVD content Using system standby With system standby pressing the button on for example your TV remote control switches your TV and all connected HDMI devices to standby mode Note Guide Manual will be available in the sublist of T Link option when T Link function is turned on and CEC devices are connected With this function you can operate a virtual control by using the TV remote control Common interface Encrypted digital TV channels can be decoded with a common interface module and a card provided by a digital TV service operator The common interface module may enable several digital services depending on the operator and services you choose for example pay TV Contact your digital TV service operator for more information about services and terms Using the common interface module WARNING Switch off your TV before inserting a common interface module Be sure to follow the instruction described below Wrong insertion of a common interface module may damage both the module and your TV 1 Following the directions printed on the common interface module gently insert the module into the common interface slot on the TV 2 Push the module in as far as it will go
18. bright light sources will shine directly onto the screen EN ta The button on the TV set or the KA non the remote control can be used to switch iton and aa into standby mode If you are not going to be watching he TV for a lengthy period of time switch it off complet y removing the plug from the mains power socket During thunderstorms we recommend that you disd ennect the TV set from the mains and aerial so that it is not a A by electrical or electromagnetic surges that could damage it Sy this reason keep the mains and aerial sockets accessible they can be disconnected if necessary O Unplug the TV set immediately if you notice it giving off a SA smell of burning or smoke You must never under any circumstances open the TV set yourself as you run the risk of an electric shock in doing so TV screen The TV screen used in this product is made of glass Therefore it can break when the product is dropped or impacted upon by other objects The TV screen is a very high technology product giving you finely detailed pictures Occasionally a few nonactive pixels may appear on the screen as a fixed point of blue green or red This does not affect the performance of your product Care Use a glass cleaning product to clean the screen and a soft cloth and mild detergent to clean the rest of the set Important Using strong detergents alcohol based and abrasive products may damage the screen Dust the vents at th
19. c and watching videos from a USB storage device oooooeu 12 POIO sizusn 12 Contents KA Important information Z ssendstuanikat hbnshsk dklado a ni 1 MUSIC s ekossko sebou hov tk d va Qe ee ne 12 any eion BOO ae nsi nho rodnom Pp fr 12 lak uz NE Time detection ooorooonnnn pas 13 Connecting the power and antenna 4 Diagnostics on digital TV channels Ly AJ 13 DVD recorder cable receiver oooono oe 4 Reset shop ceccccccsccccescecsseecsssecsecesseeees SA 13 DVD player home theatre system PC Customising the input settings 13 headphones ss5sse kosna s Erin t nos ba ia nan 5 Using Electronic programme guide 8 Blu ray Disc player HD game console 8 PVR Personal Video Recorder 13 HD camcorder orrrrsrnin ini S Schedulelist oouoonoonoonronnnnnu 14 Chapter 2 Getting started erererernna 6 Network connectiol s a enia zd ka niva s l rn 14 Remote control functions ooorrnnn non 6 Chapter 6 Other information r 22 15 Switching the TV on and off l Password in Parental Control ee 15 Chapter 3 Installing channels 8 OSS Notice susriu nshorii ten ia hv O Tdo 15 tla Sed zosist da O a nn 8 Chapter 7 Troubleshooting and Help Line 1
20. cannot coexist on the same screen If Subtitle is set to On MHEG will not appear 3 Press the red button or TEXT on the remote control 4 Press A V lt b gt to select or highlight items 5 Press OK to confirm or activate 6 Press one of the colour buttons to select an option 7 Press TEXT or Exit to exit Viewing photos playing music and watching videos from a USB storage device Your TV is fitted with a USB connector that enables you to view photos listen to music or watch videos stored on a USB storage device Supported file formats Photo JPEG Music MP3 Video AVI MP4 MPG MPEG TS Notes Some USB keys and USB products like digital cameras or mobile phones are not fully compatible with USB 2 0 standard so they may not work with the TV multimedia player Not all USB keys or devices are compatible with the USB function Not all above formats are recognised The encoding formats of your files will determine whether or not they can be used When a USB device is detected it enters the Media center menu directly To enter the Media center manually press Menu on the remote control and select Media Photo Use this function to display photos if available 1 Select Media center gt Photo then press OK to enter the main file content browser 2 In the main file content browser use A Y lt b gt to select a photo or an inner file folder 3 Select an inner file folder press OK to enter a sub file conten
21. ce In the menus they have the followifza functions PR A 4 PR M VOL gt lt OK Switching the TV on and off 1 When the power cord is connected the TV will be turned on directly or be in standby mode If the TV is in standby mode press the or PR PR button on the set or the button on the remote control to turn it on 2 To put the TV into standby mode press the button on the set or the button on the remote control The TV set remains powered up but with low energy consumption 3 Toswitch off the TV unplug the mains socket from the mains outlet On certain models you have to turn on the power switch first EN Chapter 3 Initial setup Initial setup involves selecting all the settings reguired to be able to search for and store all the analogue and digital channels you can receive Make sure that the television is switched on and follow all the steps in turn specified hereafter Note If the channel search retrieved only the analogue channels it could be caused by poor broadcasting and therefore is not covered by manufacturer warranty Manufacturers cannot be held responsible for lack of or poor broadcasting in some areas The first time you switch the set on the Initial setup wizard opens which guides you through the initial setup process Initial Setup Language Please select your language English Benrapcku Hrvatska Cesky Dansk 1 Press A Y to select your language then
22. e back and sides regularly Using solvents abrasive or alcohol based products could damage the TV set If an object or liquid enters the appliance unplug it immediately and have it checked by an authorised engineer Never open the appliance yourself since this may put you at risk or damage the appliance Batteries Batteries shall not be exposed to excessive heat such as sunshine fire or the like Remove batteries when the remote control is not to be used for a long time Batteries left in equipment may cause damage through deterioration and corrosive leakage invalidating the guarantee To protect the environment use local recycling facilities for battery disposal Dispose of used batteries according to the instructions CAUTION Risk of explosion if batteries are replaced by an incorrect type Replace only with the same or equivalent type recommended by the equipment manufacturer Hanging the TV set on the wall Warning This operation requires two people To ensure a safe installation observe the following safety notes e Check that the wall can support the weight of the TV set and wall mount assembly The TV can be mounted on a wall using a 200mm x 100mm for LT 32HA48U or 400mm x 400mm for LT 39HG42U VESA mounting kit supplied separately Follow the mounting instructions provided with the wall mount For certain models make sure to screw the hexagonal VESA wall mounting screw bosses and screws provided with the set into th
23. e contact your local municipal office your household waste disposal service or the shop where you purchased Dear Customer This apparatus is in conformance with the valid European directives and standards regarding electromagnetic compatibility and electrical safety European representative of the manufacturer is TCL Operations Polska Sp z 0 0 ul A Mickiewicza 31 41 96 300 Zyrardow Poland Email adress zyeee tcl com Figures and illustrations in this User Manual are provided for reference only and may differ from actual product appearance Product design and specifications may be changed without notice EN 2 Enabling subtitle languages on digital TV channels 10 Selecting a subtitle type on digital TV channels 10 Selecting decoding page language in Teletext 10 Digital Teletext language ooooonno u 10 SPDIF Ype sistddinitskos u oren denkin kon vo 10 TEPLU eerie A E EE 11 Enabling or disabling T Link ssssssssssserseesen 11 Using one touch play zsessovirns vse tote nvr sn nnn vo 11 Using system standby s ssindkass dsiksodocsd slovia 11 Common interface ccceeceeeceeeeeeeeeeeeeenes 11 Using the common interface module 11 Accessing common interface services 11 Software update ccccceceeceeeeeceeseeeeeeeees 11 Changing to Shop or Home mode 11 MHEG function n skok o o a 12 Viewing photos playing musi
24. e nuts for the wall mount at the back of your set before your wall mounting e The TV set must be installed on a vertical wall I III IIIT ID l Q e Make sure to use only screws suitable for the material of the the product Q wall The screw thread length must not exceed 14 5mm for Penalties may be applicable for incorrec jsposal of this waste LT 32HA48U or 9 7mm for LT 39HG48U into the TV in accordance with national legislation e Make sure that the TV set cables are placed so that there is Business users hy no danger of tripping over them If you wish to dispose of this product please cont our All other safety instructions about our TV sets are also supplier and check the terms and conditions of the purghase applicable here contract K Other Countries outside the European Union Ga Placing the TV on a table and other surfaces These symbols are only valid in the European Union If you 48 Before setting up your television set make sure that the wish to dispose of these items please do so in accordance with surface you want to put the set on can support its weight applicable national legislation or other rules in your country for cA Do not place the set on an unstable surface e g moving the treatment of old electrical equipment and batteries G shelf very edge of a unit and make sure that the front of the television set does not overhang the surface it is standing on To avoid TV from falling please fasten TV to the wa
25. e with operating this product you can phone the help line onthe safety leaflet accompanying these instructions b Analogue TV Sound Interference from cars fluorescent Turn off one piece of eguipment at a time to lights video recorder a radio broadcast see if the interference clears See also what personal computer or other equipment to do for picture interference Stereo switching to mono A weak signal or a mono broadcast Check the signal and your aerial system Analogue TV Picture Your video recorder could be faulty Crackling noises or distorted sound If you have a video recorder try plugging the Tansmiteriro bi aerial directly into the television If the fault Grainy snowy picture clears the video recorder is probably faulty Aerial nas moved is damaged or has Have your aerial system checked been disconnected The aerial is receiving reflected signals Try to tune in a better signal from the same Extra outlines on objects in from hills or buildings television station the picture ghosts Faulty aerial system Get your aerial system checked Try to tune in a better signal from the same television station Get your aerial system checked Weak aerial signal Interference from electrical equipment Picture interference like such as power tools and motors spots or streaks Move the interfering equipment further away Settings for the digital video equipment orif possible turn iton output
26. g the selected source label will be displayed after the name of the related connector in the source list when selecting Source in the Menu or pressing Source on the remote control or OK on the TV set Note Not all models have OK button on the set EN A Using more of your TV Cy Using Electronic programme ide EPG is an on screen guide that disbigys scheduled TV programmes You can navigate s lggt view and record programmes 1 Press Guide on the remote control the Now and Next EPG menu will appear which al OA you to get information about the current or ne programme playing on each channel Navigate through the different programmes using the navigation buttons on the remote control 2 Use the colour buttons to view the 8 Days EPG Prev day Red Lists the previous day s EPG Next day Green Lists the next day s EPG View detail Yellow Displays the description of this programme if available Type filter Blue Programme guide filter for digital TV programmes Press the blue button to display the programmes type and subtype if available lists Navigate through the different types and subtypes using the navigation buttons on the remote control Select one or more types which you want to highlight from the Type list press OK to select or deselect A checkmark will appear to the left of the type when selected When you select a type all its subtypes will be selected automatically Also y
27. ice when the system is reading a file or transmitting data otherwise the system or the device may be damaged Schedule list This function is used to perform scheduled recording 1 2 3 Press Option on the remote control and in the Quick access menu select Schedule list Press OK b gt to display the schedule list To add a schedule into your schedule list press the red button first to display Schedule list Then Channel number use lt gt to select the EN O Using more of your TV Gy channel number Start date use the numeric ayy to set the recording date Start time set the start time of the ording Stop time set the stop time of the re che Schedule type e Set Reminder to be reminded that you k switch to the scheduled programme when the time you have set comes When time is out and you do not execute any operation the dialog box will disappear and no further operation will be executed e Set Record to check if you really want to start your scheduled recording when the time you have set comes When time is out and you do not execute any operation scheduled recording will start automatically Repeat type set different repeat modes for the recording K 4 Press A V lt D gt to select Add then press OK to add the schedule you set into your schedule list 5 Press the red button to repeat above procedures to add another schedule 6 If you wish to edit or delete a
28. ke a few minutes During the process you can press Menu to abort halfway 5 Once the automatic search ends press Menu to return to the previous step or press OK to restart your channel search 6 After the automatic search channels are arranged in a preset order You can skip channels modify the preset order or rename channels Using your TV Accessing channels Using the numeric buttons press the corresponding numeric buttons to access the channels Using the PR or P buttons scroll through the channels Watching connected devices There are three ways for you to select connected devices on your TV you can press Menu on the remote control and select Source use OK button to enter then press A V and OK to select your wanted connected device You can also repeatedly press Source on the remote control or OK on the TV set to toggle between TV and other input sources To resume TV viewing press any numeric button to enter the channel while P will cycle through all TV channels and other input sources EN O u Using your TV amp Using more of your TV Q Note Not all models have OR phutton on the set O 4 Volume 4 Volume control use the VOL buttons gp the TV set or V buttons on the remote control to incr ase or decrease the volume QW Sound mute press the Mute button to temporar mute the sound Press this button again or the V G O button to restore it S Using TV menus KS 1 Press
29. layback begins from the selected song Press Menu to display the music menu in the browser mode You can play or pause the song select different play modes etc Show lyrics This option is available for the songs with lyrics Select it and use lt gt to turn on off lyrics synchronized display Audio only Select and press OK to listen to the music with the screen turned off Pressing any key will turn the screen on Press the related buttons on the remote control to perform the available functions shown on the function bar at the bottom of the TV screen Video Use this function to watch videos if available iP 2 12 Select Media center gt Video then press OK to enter the main file content browser Use A V lt b gt to select a video in either main or sub file content browser in the same way as in photo display function press Menu to display the video menu in folder mode Sort Sort folders and videos by Type modification Date or Name Edit Copy paste or delete a selected video a Parser You can select Recursive to display videos from all sub file folders 3 Select a video press OK to watch and automatic playback begins from the selected video Press Menu to display the video menu in the browser mode You can play or pause the video select different play modes screen modes and preset picture settings etc 4 Press the related buttons on the remote control to perform the a
30. ll by using necessary screws in Vesa wall mount holes clamps anchors to be bought separately Install TV near to the wall to avoid falling backwards Multi product user manual The features described in this manual are common to most models Some features may not be available on your TV and or your TV may include features that are not described in this user manual The illustrations in this manual may differ from the actual product Please refer to the actual product Information for Users on Disposal of Old Eguipment and Batteries European Union 15 These symbols indicate that the electrical and electronic eguipment and the battery with this symbol should not be disposed of as general household waste at its end of life Instead the products should be handed over to the applicable collection points for the recycling of electrical and electronic eguipment as well as batteries for proper treatment recovery and recycling in accordance with your national legislation and the Products Pb Battery Notice P 3 The sign Pb Directive 2002 96 EC and 2006 66 EC aie By disposing of these products correctly you batteries will help to conserve natural resources andwill areas help to prevent potential negative effects on contains lead the environment and human health which could otherwise be caused by inappropriate waste handling of these products For more information about collection points and recycling of these products pleas
31. ou can select some desired subtypes without selecting any type first Press the blue button to exit the type and subtype list e After filtering all your desired digital TV programmes will be highlighted Add schedule Option Press Option on the remote control to bring up the Schedule list menu For details on scheduled recording refer to the Schedule list section 3 Press Guide Exit to exit the EPG and switch to the selected channel PVR Personal Video Recorder Allows you to record non encrypted TV programmes Before you use the function connect a USB memory device to the set first When using this function for the first time you should setup the disk for the USB device Note This feature is available only in selected products and due to specific TV network limitations and country technical requirements might not be available in product or place of installation This feature might be also blocked by TV network due to copyright protection HD content recording protection Please use Option on the remote control to check if this feature is available in your product 13 Press Option on the remote control and in the Guick access menu select PVR Press OK b gt to enter Press the red button to start recording the record file is put into a folder named after the channel number under the PVR folder in Media center gt Video the green button to stop recording manually if the recording duration finishes the
32. ou to select an available language as primary language which relates to different initial Teletext pages Press Menu on the remote control and select Options gt Digital teletext language Press lt P gt to select SPDIF type Connect to an audio device through the SPDIF output Press Menu on the remote control and select Options gt SPDIF type Select a proper sound type from the list for digital programmes If the current programme outputs sound in Dolby D format then either PCM or Dolby D can be selected If the current programme does not output sound in Dolby D format only PCM can be selected Otherwise no sound will be output Select Off to turn off the audio output from the audio device connected to the SPDIF output Note The options you may choose depend on the programme you are watching If you select PCM and the sound is ahead of the picture you can select SPDIF delay from the Options menu and press lt gt to adjust the delay time to synchronise the sound with the picture 10 T Link Use this function to search for CEC devices connected to the HDMI sockets in your TV and enable one touch play and one touch standby between CEC devices Enabling or disabling T Link 1 Press Menu on the remote control then select Options gt T Link 2 Press lt P gt to select On or Off if this function is turned on T Link option will be available in the Quick access menu which you can enter by pressing the
33. r Blu ray Disc player E Bluray Disc HDMI 1 ARC 4 Notes Not all connections available on all models The location of the power socket on the TV may vary according to TV model The positions and names of the function buttons and connectors on the TV may vary according to TV model EN 5 Op Chapter 2 Getting started Q Remote control functions Vo Cy Most of your television s functions are available via the menus that appear on the screen Th amp remote control supplied with your set can be used to navigate through the menus and to configure all the gene one 4 Source To select connected devices gt a Standby quit standby A 0 9 To select a channel page or setting ECO To select desired power saving mode Guide To toggle the Electronic Programme Guide on or off only available for digital A channels Menu To access the main menu to return to the previous menu Exit To exit the menu structure or Teletext AY To navigate in the main menu to select menu options to switch to the previous or next photo song or video in USB function lt P To navigate in the main menu to set functions and change values can also be used to open the corresponding submenu Zoom To select the picture format Note You are recommended to use the full screen mode Do not use the display mode with black bars on both sides of the picture such as 4
34. re has been downloaded successfully you will be prompted to decide if you want to install it right now If yes follow the on screen instructions to complete your installation You can also select to ignore the installation here Select No under Auto download to decline the automatic download Select Manual OAD download and press OK gt to start manual scanning the latest software Follow the on screen instructions to complete During the scan press OK Exit to cancel or exit the process Changing to Shop or Home mode 1 Press Menu on the remote control and select Options gt Location 2 Press lt gt to select your location Shop or Home 3 Press Exit to exit Note According to the regulation of European Commission 2009 125 EC in Home mode TV will be put into standby mode automatically if there is no operation in 4 hours This feature can be deactivated in Options menu 11 MHEG function Some digital TV broadcasters offer dedicated digital text or interactive services for example BBC1 These services work like normal Teletext with the addition of number colour and navigation buttons This function is not available in all countries Please contact your broadcaster to check if MHEG function is supported 1 Press Menu on the remote control and select Options gt Subtitle gt Subtitle 2 Press lt b gt to set Subtitle to Off Note For some models MHEG and subtitles are mutually exclusive and
35. ress OK b gt to enter ECO settings 2 Press lt gt to select desired power saving mode to achieve the desired power saving effect The Picture preset option under Picture will now be set to Personal simultaneously 3 Press Exit to close the menu Shortcut operation Press ECO on the remote control to perform the same function mentioned above Audio description Audio description refers to an additional narration track for blind and visually impaired viewers of visual media including television programmes and movies The description narrator talks through the presentation describing what is happening on the screen during the natural pauses in the audio and during dialogue if deemed necessary You can use this feature if the current broadcast contains audio description 1 Press Menu on the remote control and select Sound 2 Press OK to enter 3 Use A V to select Audio Description press OK gt to enter use lt P gt to turn this function on or off Volume level can be adjusted by using the Audio Description menu Using subtitles You can enable subtitles for each TV channel Subtitles are broadcast via Teletext or DVB T DVB C digital broadcasts With digital broadcasts you have the additional option of selecting a preferred subtitle language Turning on off subtitles 1 Press Menu on the remote control and select Options gt Subtitle 2 Press OK gt to enter Subtitle Subtitle On Digital subti
36. rial system Try connecting the aerial directly to the digital TV receiver and then re tuning If some equipment has a radio frequency modulator switch it off or change the frequency of it and re tune the analogue TV Please see other eguipmen s instructions for how to do this DVB T Digital Video Broadcasting Terrestrial is broadcast in groups of channels on one common frequency This arrangement is known as a Multiplex There are several multiplexes in the DVB T system each carrying a group of channels If the signal level on a particular multiplex frequency is poor you may lose the whole group of channels on that multiplex Avoid old cables and adapter devices Use only modern cables Picture is the wrong size or the source device computer DVD player set top box and so on will not let you set up the pixel resolution the display can reproduce Picture looks squashed or stretched even though the aspect ratio controls are set correctly for example 4 3 or 16 9 No picture Source device has not read the set up data from the display Connecting cable does not have all the necessary connections Equipment feeding the display is set to the wrong aspect ratio Brightness and contrast levels are set to minimum Make sure the source type is set correctly EN 17 Re start the source device after connecting and powering up the display Change the graphics adapter in your computer Check compa
37. t browser 4 Use A V lt b gt to select a photo in either main or sub file content browser press Menu to display EN O Using more of your TV the photo menu in folder mod Sort Sort folders and photos Priv ta Date or Name Edit Copy paste or delete a sala photo Parser You can select Recursive to X photos from all sub file folders Select a photo press OK to watch and a s show begins from the selected photo Press OK pause the photo if you want to rotate the paused S photo Press Menu to display the photo menu in the browser mode You can play pause or rotate the photo select different play modes and displaying effects etc Press the related buttons on the remote control to perform the available functions shown on the function bar at the bottom of the TV screen Press the Info button to show or remove the function bar Music Use this function to playback music if available 1 2 Select Media center gt Music then press OK to enter the main file content browser Use A V lt b gt to select a song in either main or sub file content browser in the same way as in photo display function press Menu to display the music menu in folder mode Sort Sort folders and songs by Name Genre Artist or Album Edit Copy paste or delete a selected song Parser You can select Recursive to display songs from all sub file folders Select a song press OK to play and automatic p
38. tible video resolutions given in these instructions On the equipment feeding the TV choose the correct output aspect ratio such as 4 3 old conventional or 16 9 or 1280 x 720 or 1920 x 1080 pixels to match wide screens Increase the brightness and contrast settings Select proper source input The volume is set to minimum The mute is switched on No sound Make sure the headphones are not connected Picture is too dark too light Wrong colour adjustment in menu or tinted Wrong brightness adjustment in menu Picture is not clear Remote ZA Troubleshgoting and Help Line Z Turn the volume up O Press the mute button to rel se mute 4 Disconnect headphones 4 Adjust saturation in menu Adjust brightness in menu Batteries exhausted Wrong functions or short Obstacle in the way range Dirty remote control sensor on TV Insert new batteries Remove any objects and aim from straight in front of the remote sensor with a clear line of sight Try to clean the remote control sensor lens on the TV with a soft cloth Mains supply missing Television seems dead no lights come on and nothing Main power switch is off works Blown fuse or circuit breaker Does not respond to remote or local controls Micro controller confused by electrical disturbance Stuck on stand by Does not respond to certain controls on the TV or remote control Channel installation
39. tle language English 7 Digital subtitle language 2nd Subtitle Type English Normal Select Back Exit 3 Select the Subtitle option and press lt P gt to select On Off to turn on off subtitles EN A Using more of your TV O Enabling subtitle languages o gig ital TV channels 1 Press Menu on the remote contfgl and select Options gt Subtitle gt Digital subtitle language 2 Press lt gt to select a subtitle langualgg as your preferred language P 3 Press A Y to select Digital subtitle lang e 2nd Q 4 Press lt P gt to select a secondary subtitle language 5 Press Exit to close the menu Shortcut operation Press SUBTITLE on the remote control to directly select a subtitle language available for the selected digital TV programme O Selecting a subtitle type on digital TV channels 1 Press Menu on the remote control and select Options gt Subtitle gt Subtitle type 2 Press lt b to select a subtitle type You can select Hearing impaired to display the hearing impaired subtitles with your selected language Selecting decoding page language in Teletext Press Menu on the remote control and select Options gt Decoding page language Select a proper type of language in which Teletext will display Digital Teletext language For digital TV channels your TV could change to a service with multiple initial Teletext pages in different languages This function allows y
40. upted wait for the message indicating that the setup is complete Before starting the scanning you can also select Skip scan to skip the initial setup process During the setup you can follow the hints available at the bottom of the screen to return to the previous step by pressing lt Or press Exit to exit or interrupt the search halfway Once the automatic search ends the set enters the next step automatically Press A V to select your location Shop or Home Press OK gt to confirm your selection and enter the last step In this step you can press OK to exit the initial setup The channels are arranged in a preset order If you wish to skip channels modify the preset order or rename channels select Setup gt Organiser and press OK gt to enter In this step you can also press lt to return to the previous step Performing an automatic channel search This section describes how to search and store channels automatically Instructions are for both analogue and digital channels 1 Press Menu on the remote control and select Setup gt Language gt Menu language Press lt gt to select your desired menu language Press Menu to return to Setup Press A V to select Country then press lt P to select your country The TV installs and arranges channels according to your country Press A Y to select Tuner mode then press lt gt to select Antenna or Cable Select Antenna e Press A F to
41. vailable functions shown on the function bar at the bottom of the TV screen Press the Info button to show or remove the function bar Time detection You can detect the time from digital channels using the following operations 1 Press Menu on the remote control and select Timer gt Clock gt Auto synchronization 2 Press lt b to select On To set the time manually switch off the Auto synchronization Diagnostics on digital TV channels 1 Press Menu on the remote control and select Setup gt Diagnostics 2 Press OK to display some signal information on the current digital channel such as signal strength freguency etc Reset shop Allows you to reset the TV to factory default settings 1 Press Menu on the remote control and select Setup then press OK to confirm Select Reset shop and press OK b gt to enter Use the numeric buttons to enter the password Press lt gt to select OK and press OK to confirm The lnitial setup menu appears Follow the related instructions Tee N Customising the input settings You can configure your TV according to the equipment you connect to it 1 Press Menu on the remote control and select Setup gt Input settings 2 Press OK gt to enter Input settings 3 Press A Y to select a connector your equipment is connected to 4 Press lt P gt to select the type of apparatus attached to this connector 5 Press Menu to return to the Setup menu After configurin
42. zard The ventilation should not be impeded by covering the ventilation openings with items such as newspapers table cloths curtains etc The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids such as vases shall be placed on the apparatus This apparatus is not suitable for use in a tropical climate WARNING To prevent injury this apparatus must be securely attached to the floor wall in accordance with the installation instructions CAUTION Connect headphones with the volume set low and increase if required Prolonged listening through headphones at high volume settings can result in hearing damage No naked flame sources such as lighted candles should be placed on the apparatus Ventilation Place the television on a hard flat surface away from direct sunlight or heat sources If it is in a cabinet allow at least a 10cm gap all around Do not obstruct the ventilation slots including those underneath with soft furnishings Overheating will shorten the life of the television and increase the risk of fire Eye Fatigue When using this product as a computer monitor health and safety experts recommend short frequent breaks rather than occasional longer breaks For example a 5 10 minute break after an hour of continuous screen work is considered to be better than a 15 minute break ever 2 hours Do not use the monitor against a bright background or where sunlight or other
Download Pdf Manuals
Related Search