406MHz GPS EPIRB - Polaris Electronics A/S
Contents
1. Appendix 14 33 0 518111 United States EPIRB registry RECOMMENDATIONS AND SAFETY NOTICES This EPIRB is an emergency device for use only in grave and imminent danger False alarms cost lives and money Help to prevent them understand how to activate and disable your equipment Read the complete manual before installing testing or using the EPIRB Ensure the EPIRB is registered with your local authorities Flag State nation The EPIRB contains no user serviceable parts Return to your dealer for battery replacement or other service Do not open Retain the original packaging Dispose of this device safely Contents include Lithium batteries do not incinerate puncture deform or short circuit This device emits radio frequency radiation when activated Because of the levels and duty cycles such radiation is not classed as harmful however it is advisable not to handle the antenna while the unit is activated It is advisable not to stare directly at the strobe 2 2 PURPOSE An Emergency Position Indicating Radio Beacon EPIRB is used to alert search and rescue services in the event of an emergency lt does this by transmitting a coded message on the 406MHz distress frequency This message is relayed via satellite and earth station to the nearest r2. he hl he he EZ A A Le O A E SAILOR 406MHz GPS SATELLITE EPIRB SAILOR MARINE PRODUCTS ALL FCC ID 6 82 01 Notified Bedy DERA No 0191 4 5 Year 99 8 Murdo Itd portsmou A 406 GPS EPIRB USER MANUAL 2 Recommendations and Safety notices 1 3 00 0 0 1 e 2 2 1 12 2 2 2 2 AAA e A 4 1 SSS e ains 4 1 3 1 5 A A A enclosure 2 3 2 Manual EPIRB m 6 06 aii ida 6 3 3 od e a el EE 7 7 0001171 1 ON BUIO Man ig addons lado 7 4 2 7 SONS WIE q POP A PES CO Om O 4 3 E a o An o ee 8 4 4 9 Operating procedues ele ee eee 5 9 0000 1 1 1 1 1 1 1 1 1 1 1 5 1 9 21000611111 5 2 Releasing EPIRB from a wall bracket sess 9 5 3 Releasing EPIRB from an enclosure esses 10 5 4 i 10 a a eet 00 Manual Activations 5 5 Dl e eet eee 11 5 6 11 000 Battery 5 7 AS EES 11 RIS ine EEE a dees 0 5 8 E 1 0009 13 RAISE 6 lee ee 13 065 56 00 16 Stand 6 1 Deactivate the EPIRBLS SSIES SESS SS SSS SAE aE
3. 5 OPERATING PROCEDURE An EPIRB is a piece of life saving equipment lts sole purpose is to call for help It must only be used in situations of grave and imminent danger Misuse can involve a severe penalty 5 1 Sinking If you have a category 1 float free enclosure see marking on enclosure label then if your vessel sinks the EPIRB will automatically release itself from its enclosure before it reaches a depth of 4 metres The EPIRB will float to the surface and start to operate because its sea switch is activated If possible the EPIRB should be recovered and tied using its lanyard to one of the liferafts An EPIRB is meant to mark survivors not the accident scene OD ly For best operation leave the EPIRB AN floating in the sea near the liferaft Do not operate the EPIRB inside the liferaft or under any cover 5 2 Abandon ship If the vessel is sinking and there is time to fetch the EPIRB then this should always be done Release the EPIRB from its mounting bracket as described in section 5 3 or 5 4 and carry it to one of the liferafts Once the liferaft is in the water uncoil the lanyard and tie it to the liferaft then throw the EPIRB overboard so that it floats next to the liferaft The EPIRB will operate because its sea switch will activate 5 3 Releasing EPIRB from a wall bracket If you have an EPIRB fitted into a wall bracket then follow the instructions below to release it from the bracket Squeeze top un
4. e Mount at least 1 metre 3 from any compass equipment e Allow at least 25mm 1 above the bracket for it to spring open e Allow 18cm 7 for the antenna Heavy bending of the antenna is bad 7 2 Mounting procedure The wall bracket is supplied with a set of stainless steel fixings 25mm 1 in length The bracket mounts against a flat surface using 4 fixing points Offer the bracket into the chosen position and mark through the mounting slots If you are using the nuts and bolts supplied drill 6mm 1 4 holes in the centre of each mark You will need a 4mm Allen key to tighten the bolts If the rear of the mounting surface is inaccessible then use the self tapping screws supplied and drill 3mm 1 8 holes Always fit washers under the heads of the screws to avoid damage to the plastic 175mm 7 15 7 2 1 Mounting instruction plate The EPIRB is supplied with an instruction plate This is a rigid plate with basic visual instructions for how to operate the EPIRB in an emergency The plate varies slightly depending on whether you have a wall bracket or a full enclosure The wall bracket version is illustrated below 58 4mm 2 3 E A O Y Mount plate next to EPIRB 130mm ree 16 3mm 4 58 The instruction plate should be mounted next to the EPIRB so that it is easily visible in an emergency Use the four self tapping screws supplied to mount the plate Mounting dimensions are show
5. the beacon Emergency Contact It is VITAL that the Emergency Contact information is accurate particularly regarding the telephone number as this will be used to validate an alert Only if the beacon registration and approximate location details can be confirmed will USCG United States Coast Guard launch an immediate rescue otherwise there will be a delay whilst further alerts from the same source are received and verified Registration address NOAA SARSAT Beacon Registration E SP3 RM 3320 FB 4 5200 Auth Road Suitland MD 20746 4304 FAX 301 568 8649 Helpline 301 457 5678 or toll free 1 888 212 SAVE 7283 33 Owner s notes 34 McMurdo Limited Product Warranty Subject to the provisions set out below McMurdo Limited warrants that this product will be free of defects in materials and workmanship for a period of 24 months from the date of purchase McMurdo Limited will not be liable to the buyer under the above warranty e for any defect arising from fair wear and tear wilful damage negligence abnormal working conditions failure to follow McMurdo Limited s instructions whether oral or in writing including a failure to install properly and or to use batteries recommended and or supplied by McMurdo Limited misuse or alterations or repair of the product by persons other than McMurdo Limited or an Approved Service Agent e for parts materials or equipment not manufactured by McMurdo Limited in respect of which t
6. card and fax the information to the NA The original card must still be mailed to the NA for hard copy reference and filing If the current owner is transferring the beacon to a new owner the current owner is required to inform the NA by letter fax or telephone of the name and address of the new owner The subsequent owner of the beacon is required to provide the NA with the information shown on the owner registration card This obligation transfers to all subsequent owners 21 NA is the Australian Maritime Safety Authority or the Maritime Safety Authority of New Zealand as appropriate Respective fax numbers are 06 257 2036 Australia and 04 382 6482 NZ 22 10 MAINTENANCE 10 1 Monthly self test 8 inspection As an important item of safety equipment your EPIRB should be checked regularly The EPIRB has a built in test capability that can be used as a confidence check This self test confirms that the battery is healthy that the GPS receiver and both of the distress transmitters are functional and that the strobe light is operational The self test should be performed monthly but not more frequently It should be performed during the first 5 minutes of the hour to minimise disturbance on the emergency channel If your EPIRB is in an enclosure it can be tested through the test window without having to remove the EPIRB from the housing If you have a bracket mounted EPIRB it will have to be removed from the bracket as described in se
7. switch cover fully to the 2 HOLD TO right Y e Press and release READY button rr _ If EPIRB is still flashing then it has a fault Refer to section 6 on False Alarms 5 7 Battery condition If your EPIRB has been activated for a cumulative period in excess of 2 hours then its battery will need replacing This is necessary to ensure that the next time it gets used it will operate for the full 48 hours required by government regulations See section 10 3 for battery replacement instructions 5 8 Re fitting EPIRB 5 8 1 Refitting into wall bracket The EPIRB is now in its ready state but its sea switch is still armed and will activate if it gets wet To de activate the EPIRB fully it must be returned to its mounting bracket where a magnet hidden in the bracket will make the EPIRB safe 9 8 2 Push down Insert until clip locks antenna t Push backwards a Push firmly 3 Into Cup 11 Re fitting into enclosure e Offer EPIRB into backplate with switches facing outwards e Engage base of EPIRB into D shaped metal prongs e Antenna rests either to left or right of release pin e Check EPIRB is fully engaged in metal prongs and resting on foam pad e Refit cover by first locating release pin through hole in cover e Locate cover onto backplate then snap down over locating lug e Refit R clip through hole in end of release pin Switches facing out CAUTION Failure to fit EP
8. view over their area of coverage so that reception of the EPIRB signal is instantaneous GEOSAR coverage 31 Global Positioning System GPS The GPS system is a satellite array which enables a receiver located anywhere on Earth to determine its exact position usually to within The array uses 24 satellites plus spares orbiting the Earth in six orbital planes four satellites per plane as shown below These are arranged so that at least five satellites are within range of any receiver which can be anywhere at all times GPS satellite orbital planes Each satellite transmits information which enables its position and distance from the receiver to be calculated By combining these data for multiple satellites the exact position of the receiver can be determined Operation of GPS receiver size exaggerated for clarity 32 UNITED STATES EPIRB REGISTRY SYSTEM Important information Beacon registration is now available on line This is the preferred method of registration point your browser to htip www beaconregistration noaa gov and follow the instructions on screen Use the EPIRB form Other Information At present NOAA still accepts registration by mail or fax The registration forms are pre printed with the correct mailing address and fax number A registration form may be downloaded from the website given above However you register the beacon you will be sent a sticker which must be attached to
9. 13 6 2 14 Dealing with a transmitting EPIRB 6 3 15 T _ Wall Bracket 5 1 0 11 2222233223 aS SIMO Sea DE SE E Se E o 15 7 1 MOUNINO Proc Us 1 1 1 1 1 1 2 1 00000000 15 7 2 S Enclosure 5 idos 17 esco 17 SII O N 8 1 Mounting POCO US csi td 17 8 2 instra ction plate ica AAA 18 8 3 we een oe ere nner 18 a OS re een 1 1 1 1 Marking HERU OXY 8 4 19 ld Marking Vessel NAME 8 5 20 0000600 00 1 1 9110 REGUS UT 9 20 1000 1 1 1 1 1 1 1 0 1 OV GINO WY 9 1 20 E EES E 011 10160151617 9 2 NANO A NA A 21 9 3 de S tele 21 1 1 Radio 9 4 21 E A E e 9 5 Maintenant e ip 23 10 usas o 23 12586611011 amp 6 6 10 1 riot 24 ARU Tela co Men 10 2 Bater replace lero li EE SE A RA 25 10 3 A A A A AES 25 10 4 25 00000000 1 Tra 10 5 25 GMDSS MSPC Sada 10 6 a 27 Fully disabling AN EPIR B scala 11 Technical specification iii A Dai a a 28 12 Declaration of 001916011131117 222 a 29 13 31
10. Canada UK and Australia do not need to be re programmed when transferred to a new vessel Simply complete another registration form to inform the authorities of the transfer Use one of the spare forms provided or contact McMurdo for a blank form See warranty section for address For most other countries the EPIRB must be re programmed with either the new vessel s Maritime Mobile Station Identity MMSI or its radio callsign whichever is required by the country controlling the new vessel Since the EPIRB identity contains a country code it follows that changing the flag state of the vessel also means the EPIRB must be re programmed Programming can be carried out at McMurdo or any of our designated agents For details of your nearest agent either contact McMurdo using the details in the warranty section or visit the McMurdo web site at www mcmurdo co uk 9 5 1 Mandatory information for Oceania Advice to owners of Emergency Position Indicating Radio Beacons Registration of 406MHz satellite Emergency Position Indicating Radio Beacons EPIRB with the EPIRB Registration Section of the NA is mandatory because of the global alerting nature of the system The information provided in the registration card is used only for rescue purposes Fill in the owner registration card immediately on completion of the sales transaction Mail the registration card immediately If the beacon is to enter service immediately complete the registration
11. IRB correctly may impair its ability to float free wy in an emergency Slide D shaped foot into prongs Fit caver over pin tote cover onto locating lug 6 Fit R ctip through pin 6 FALSE ALARMS False alarms are a serious problem for the rescue services About 90 of EPIRB initiated distress alerts turn out to be false alarms If your EPIRB should cause a false alarm follow the instructions below 6 1 Stand down rescue services It is most important that you contact the nearest search and rescue authorities and tell them it was a false alarm so that they can stand down any rescue services Use any means at your disposal to make contact Often this can be by VHF radio to the local coastguard or mobile phone if you are within coastal range but MF HF DSC and Inmarsat A B C M may also be used Useful contacts are Telephone What to report USA Atlantic Gulf of Mexico 212 668 7055 EPIRB Unique ID UIN 510 437 3700 Date time amp duration From any location 800 323 7233 Cause of activation From any location 01326 317 575 Location when activated 6 2 De activate the EPIRB If the EPIRB was activated by mistake then de activation is simple e Remove the EPIRB from any water and dry its sea switch contacts e Wait about 8 seconds for the sea switch to de activate e Ifthe EPIRB is still flashing then it must have been turned on manually e Slide the switch cover fully to the right e Press and rele
12. Precision Intended usage of products For use in all member States aboard Recreational Craft Workboats and Non SOLAS Vessels in coastal International waters certify that the products described above have been tested to the radio suite overleaf and comply with the essential requirements in Articles 3 1 a 3 1 b 3 2 and 3 3 e of the R amp TTE Directive The product will carry this Conformity Marking CE Issued on behalf of McMurdo Limited Signed Name C P Hoffman Title Technical Director Date 1 July 10803 Page 1 of 2 29 Regulations and Standards complied with Regulation IV 7 1 6 Regulation X 3 IMO Resolution MSC 36 63 14 6 1 5 1994 HSC Code IMO Resolution MSC 97 73 14 7 1 5 2000 HSC Code IMO Resolution A 699 17 IMO Resolution A 700 17 IMO Resolution A 806 19 IMO Resolution A694 17 ITU R M 491 1 07 86 ITU R M 492 6 10 95 ITU R M 540 2 06 90 ITU R M 625 3 10 95 ITU R M 668 06 90 Testing standards ETS 300 066 2 V1 3 1 2000 01 EN 60945 1997 MSC Circ 862 IEC 61097 2 1994 IEC 60945 1996 Technical Construction File Notified Body DERA Fraser Maritime Navigation Systems No 0191 Address Fort Cumberland Road Portsmouth POA UK Statement of Opinion DERA RTTE 11 00 01 Date 22 December 2000 If this product is to be incorporated into other appliances or systems then it must not be put into service until the apparatus into which it is incorporated has been d
13. arking guide To do this pull out the R shaped clip and remove the enclosure lid Note how the EPIRB fits then remove it to somewhere dry its sea switch is now armed Offer the back plate into the chosen position and mark through the mounting holes The enclosure is supplied with a set of 25mm 1 stainless steel fixings If you are using the 17 nuts and bolts drill 6mm 1 4 holes where you have marked You will need a 4mm Allen key to tighten the bolts If the rear of the mounting surface is inaccessible use the self tapping screws supplied Always fit washers under heads of the screws to avoid damaging the plastic OBSTRUCTION FREE AREA 0 8m x 0 5m 32 x 20 44mm 1 73 440mm 17 3 84mm 3 3 __ 140mm 5 5 8 3 Mounting instruction plate The EPIRB is supplied with a rigid plate giving visual instructions on how to operate the EPIRB in an emergency Mount this next to your EPIRB as explained in section 7 2 1 8 4 Marking HRU expiry If you are installing a float free EPIRB you must now mark the HRU expiry date The HRU has a 2 year in service life which starts as soon as it gets exposure to a marine environment Hence the 2 years starts at installation and it is left to the customer to mark this date during installation A date 2 years into the future should be marked on the HRU body and copied onto the label on the side of the enclosure The HRU is marked by cutting out t
14. ase the READY button e The EPIRB should now stop flashing e Refit the EPIRB correctly into its mounting bracket or enclosure Modern EPIRBs have sea switches and it is not uncommon for the sea switch to activate in rough seas or heavy rain simply because the EPIRB has been badly fitted in its mounting bracket The EPIRB bracket has a hidden magnet to hold the EPIRB in an off state If the EPIRB is wrongly fitted the magnet does not do its job and heavy seas may activate the sea switch The simple cure is to ensure the EPIRB is correctly fitted as shown in sections 5 8 or 5 8 2 13 6 3 Dealing with a transmitting EPIRB In the unlikely event that your EPIRB develops a fault and will not turn off then prevent its radio signal from reaching the satellite using one of the following methods e Remove the antenna Wrap the EPIRB in metal foil and take it below decks or e Remove the antenna and place the EPIRB in a metal container or locker Take care when removing the antenna Handle the antenna as little as possible Refer to Section 1 for warnings Leave the EPIRB in this condition for 3 days until its battery is dead See section 10 4 for instructions on returning the EPIRB for servicing See also section 11 14 7 WALL BRACKET INSTALLATION 7 1 Siting The wall bracket should ideally be sited in plain view near an emergency exit When choosing a suitable mounting position you should also consider e Ease of access in an emergency
15. ction 5 3 The procedure for self testing is as follows e On rear of EPIRB press and hold the READY button e The red lamp will come on for 4 seconds to confirm test in progress e When the red lamp goes out the strobe lamp must flash 3 times at least e Ifthe strobe does not flash or the red lamp illuminate repeat the test then see section 10 4 During these monthly checks you should take the opportunity to visually inspect the EPIRB and its mountings for deterioration or damage On the EPIRB itself check the following e Inspect the EPIRB for any obvious damage e Check there is no sign of water inside the unit e Check that the lanyard is not tied to the vessel structure e Check the battery is within its expiry date If you have a wall bracket e Confirm the bracket top clip springs up when squeezed e Check the EPIRB is correctly fitted and secure in its bracket If you have an enclosure Check the HRU is within its expiry date category 1 only Confirm the cover can be manually removed with ease Ensure the EPIRB base is correctly fitted into the D shaped prongs If the EPIRB or its mounting needs cleaning then this should be done using warm soapy water and a damp not wet cloth Do not use strong detergents or solvents Do not paint the EPIRB or its mounting Do not clean with detergents or solvents During vessel cleansing or painting remove the EPIRB and its mounting 10 2 HRU replacement If you have an EPIRB i
16. e We se Power output 50mW radiated typical ition EI Ooo i few o i ies ate LL ooo EC OC Battery Type Lithium manganese dioxide Operating life 48 hours minimum Shelf life 5 years typical in service Operating temperature 20 C to 55 0 class 2 Storage temperature 30 C to 70 C Automatic release depth 4 metres max 13 feet Physical Weight 770 grams 1 7 lb o a Height of body 21 cm 8 2 inches Length of antenna 18 cm 7 inches Approvals Satellite system Cospas Sarsat T 001 T 007 Europe ETS 300 066 Marine Equipment Directive USA USCG FCC approved FCC ID KLS 82 501 1 Worldwide IEC1097 2 Meets IMO regulations A662 16 A694 1 7 A810 19 A814 19 This device complies with the GMDSS provisions of part 80 of the FCC rules The GPS module complies with the relevant sections of IEC1108 1 1996 28 13 DECLARATION OF CONFORMITY Silver Point Airport Service Road 7 y Portsmouth m G m U rd O Hampshire UK 6 PO3 8 Int 44 0 23 9262 0 www mcmurdo co uk EC DECLARATION OF CONFORMITY The following products comply with the EU Directive 1999 5 EC Radio Equipment and Telecommunications Terminal Equipment and satisfy all the technical regulations applicable The assessment has been carried out in accordance with Annex IV of the above Directive Products covered by this Declaration Product Type 406MHz EPIRB Models McMurdo G4 Pains Wessex SOS
17. eclared in conformity with the provisions of the relevant Directive s BS EN ISO 6001 BSOODO CECC and CAA Approved Registered in England No 746503 Hagitered Office 1645 Par keray leery Fareham Hampshire POIS TAH VAT No GB 421 1393 92 A Declaration of Conformity to the Marine Equipment Directive is available on request 30 14 APPENDIX SATELLITE SYSTEMS COSPAS SARSAT satellite system The COSPAS SARSAT system provides distress alert and location information to search and rescue authorities anywhere in the world for maritime aviation and terrestrial users in distress There are two satellite arrays carrying the COSPAS SARSAT system The principal array is LEOSAR Low Earth Orbit Search and Rescue which has seven satellites in polar and near polar orbits The orbits of these satellites are arranged to scan the entire surface of the Earth on average a satellite comes into view every 45 minutes LEOSAR satellite path and scan footprint Distress transmissions from EPIRBs are picked up by the satellites and retransmitted to ground receiving stations which then pass the message to the appropriate rescue organisation On average the total delay from activation of an EPIRB to the message being received by the rescue services is 90 minutes COSPAS SARSAT is in an advanced stage of commissioning the second satellite array GEOSAR Geostationary Search and Rescue This array uses geostationary satellites which are always in
18. escue co ordination centre The satellite system is run by COSPAS SARSAT and is described in the Appendix With the geostationary satellite section being commissioned the alerting delay is reduced from typically 90 minutes to a few minutes within the geostationary satellite coverage Instant alerting is good news but they still need to know where you are The advantage of this type of EPIRB is that it has a built in GPS receiver so within minutes of activation it will have determined your latitude longitude coordinates and will have transmitted these to the rescue centre The position fix is accurate to 60m To operate properly the EPIRB needs a clear view of the whole sky If its view is blocked and it is unable to get a position fix then the system defaults to using a polar orbiting satellite to determine position In this case there is typically a 45 minute delay before the position is known and the accuracy is limited to within 5km 3 miles This is the original system that standard non GPS EPIRBs use To get the full advantage of the GPS type of EPIRB it is important to give it a clear view of the whole sky The EPIRB transmits a message that identifies the exact vessel to which it was registered Knowing which vessel is in distress allows the rescue services to eliminate false alarms and launch an appropriate rescue The EPIRB also has a secondary distress transmitter This transmits on 121 5MHz and is used for homing purpo
19. g it contains a sprung loaded lever which automatically pushes the enclosure lid off and releases the EPIRB if your vessel sinks This automatic ejection is controlled by a device called a Hydrostatic Release Unit HRU If the enclosure is submerged then before it reaches 4 metres 13 feet deep the HRU cuts a plastic rod that holds back the spring and the lid is ejected releasing the EPIRB which floats to the surface and switches on automatically The diagram below illustrates the automatic release sequence 1 As the vessel sinks the enclosure fills with water The HRU contains a blade which is released due to water pressure acting on a diaphragm Before it reaches a depth of 4 metres the HRU will operate and cut the plastic rod releasing the coil spring The spring pushes the EPIRB and the enclosure lid outwards As the lid pivots off it disengages from the screw head that helped hold it in place The lid is weighted so it rolls over and falls away As the EPIRB floats away from the lid it moves out of range of the magnet Once away from the magnet its sea switch becomes armed The sea switch activates The EPIRB then floats on the surface with its strobe light flashing After 2 minutes it makes its first distress transmission 02 4 sea switch activates LE 3 EPIRB arms once away from magnet 1 HRU cuts rod Y 2 Lid ejects Magnet LL If you need to activate your EPIRB manually it can be freed from t
20. have completed the form you can choose to fax it or mail it IMPORTANT The registration system in United States has changed See Page 31 It is usual to receive confirmation when you register In the UK and USA you will also receive a Decal sticker which you must fit to the E3 itself The Decal is proof of registration Not having a Decal is an offence Useful registration contacts are USA Sarsat Beacon Registration UK EPIRB Registry E SP3 RM3320 FB 4 HM Coastguard Southern NOAA 5200 Auth Road Pendemnis Point Castle Drive Suitland MD 20746 4304 Falmouth TR11 4WZ Tel 888 212 7283 Fax 301 568 8649 Tel 01326 211569 Fax 01326 319264 20 9 3 Warranty form Please complete the warranty form supplied and fax or mail it to McMurdo Failure to do this may delay any future warranty claim 9 4 Radio licence An EPIRB is a radio transmitter and must therefore be added to your radio licence If you have been allocated a radio callsign then you already have a radio licence for your VHF or MF radio set You should update your licence to include your EPIRB For further details see your licence or use these contact numbers USA FCC Tel 888 225 5322 Website www fcc gov Forms Form506 506 pdf UK Ship Radio Licensing Radio Licensing Centre The Post Office PO Box 1495 Bristol BS99 305 Tel 0870 243 4433 Fax 0117 975 8911 Minicom 0117 921 9550 Website www radiolicencecentre co uk 9 5 Sale or transfer EPIRBs registered in the USA
21. he buyer shall only be entitled to the benefit of any warranty or guarantee given by the manufacturer to McMurdo Limited e forthe battery storage life which is specifically excluded from this warranty e ifthe total price for the product has not been paid McMurdo Limited does not make any other promises or warranties express implied or statutory about the product except where the product is sold to a consumer in which case the statutory rights of a consumer are not to be affected In order to be valid claims must be made under the above warranty in writing as soon as practicable after discovery of the defect or failure and within the warranty period referred to above Proof of purchase will be required The claim should be sent together with the product in question to the address set out below or to an Approved Service Agent Following a valid warranty claim McMurdo Limited shall be entitled to repair or replace the product or part in question free of charge or at McMurdo Limited s sole discretion to refund to the buyer the price of the product or a proportional part of the price McMurdo Limited shall not be liable to a buyer who is not a consumer for any other loss or damage whether indirect special or consequential loss of profit or otherwise costs expenses or other claims for compensation which arise out of or in connection with this product In the case of a consumer McMurdo Limited shall only be liable where other loss or damage i
22. he corresponding dates on its label The enclosure should be marked using the alpha numeric stickers provided then covering them with the clear 18 sticky label provided but see 8 5 first The preferred date format is month and year for example JUN 2003 8 5 Marking vessel name In most countries it is usual to have your EPIRB programmed by your supplier with the vessel s existing callsign see registration section below Your supplier will then mark all the EPIRB labels accordingly However if your EPIRB was purchased in the USA Canada or UK then your EPIRB will have all the necessary markings except for vessel name In these countries it is left to the customer to mark the vessel name during installation The name must be marked on the rear of the EPIRB itself and also on the enclosure if you have one Use the alpha numeric stickers provided to mark the vessel name or its abbreviation on the top line of the EPIRB s rear label and again on the enclosure label Protect the markings with a section of the clear sticky label provided You must register your EPIRB with the appropriate authorities Failure to register may slow the rescue and lead to loss of life In the USA failure to register leads to monetary forfeit In the UK you are legally required to register your EPIRB IMPORTANT The United States registration system has changed Refer to Page 31 for information 19 9 REGISTRATION 9 1 Overview Every EPIRB
23. he enclosure after pulling out the R shaped retaining pin and removing the lid 3 3 Manual EPIRB in enclosure Customers who need to mount their EPIRB in an exposed position can select the protective enclosure without an HRU fitted c suffix This means that the EPIRB will not float free if your vessel sinks This is known as a category 2 EPIRB You can tell which enclosure you have by reading the category from the front of the enclosure G4a 406a Category 1 HRU fitted Automatic float free G4c 406c Category 2 No HRU fitted Will not float free 4 CONTROLS e s 4 1 ON button ON This is hidden behind a sliding door which protects it from accidental activation The sliding door has a tamper seal to show if the EPIRB has been activated The EPIRB can be activated manually by sliding the door to the left breaking the seal and then momentarily pressing the ON button When activated the EPIRB will start to flash immediately It will not make any distress transmissions for 2 minutes This gives you a chance to turn it off if you activated it accidentally During this 2 minutes the red lamp illuminates continuously When the red lamp starts to flash the 2 minutes delay has passed and distress transmissions have started Normally the green GPS lamp will start flashing within the first 5 minutes 4 2 READY button Y il This button de activates the EPIRB and also tests the EPIRB EADY Ready Pressing and releasing this button quickly
24. he sea switch operates properly in rough seas it has a built in time delay It has to be wet for at least 2 seconds before it will activate and it has to be dry for at least 8 seconds before it will de activate 4 4 Lamps 4 4 1 Strobe The strobe is the visual means of locating the EPIRB When activated the strobe flashes 23 times per minute with a pause during the time when the EPIRB is transmitting The strobe is also used to indicate the result of a self test see section 10 1 4 4 2 Red lamp The red lamp is used to indicate transmissions by the EPIRB When activated it flashes alternately with the strobe to indicate a good transmission on 121 5MHz Every 50 seconds it illuminates for 2 seconds to indicate a good transmission on When the EPIRB is first activated the red lamp is illuminated continuously until the EPIRB begins to transmit when it begins to flash The red lamp is also used to indicate the result of a self test see section 10 1 4 4 3 Green lamp The green lamp flashes to indicate that a valid position has been obtained by the GPS receiver Every 50 seconds it illuminates for 2 seconds to indicate that the position is being transmitted on 406MHz Every 20 minutes the GPS receiver updates its position information If a fix is not obtained the green lamp stops flashing and illuminates only every 50 seconds when the previous position information is transmitted The green lamp is not used during self test
25. is pre programmed with a unique identity before it reaches the customer This is done by the manufacturer or in some cases the distributor The identity includes a 3 digit country code This is the country that takes responsibility for storing that particular EPIRB s registration details In most cases this is the country to which the vessel is flagged The country programmed into your EPIRB can be found from its rear identity label You must register with this country MV BELLANA ee EPIRB 1 Vessel Number 1D1400063F81FE0 FLAG 232 G BRITAIN SERIALISED 000012 Country CATEGORY 1 AUTO Class 2 20 55 C 4 131 F When you activate your EPIRB in an emergency the nearest maritime search and rescue coordination centre MRCC will receive the message and decode the country code eg 232 They will then access the registration database for that country and expect to find details of your vessel its radio equipment and who to contact If they fail to find this information this may slow down any rescue 9 2 How to register Three registration forms are provided two are for future use and one must be completed now The forms are all pre printed with your EPIRB s identity all you have to do is complete details of your vessel and provide some contact numbers Wherever possible the forms are also pre printed with the correct mailing address and a faxback number If your form does not have a mailing address contact your supplier When you
26. n an enclosure marked Category 1 then it contains a Hydrostatic Release Unit HRU This has a 2 year replacement interval The expiry date which is marked on the HRU and on the enclosure side label should be checked regularly When the HRU expires you can obtain a replacement at a local chandler or direct from McMurdo at the address shown on the warranty page McMurdo will supply an HRU kit Part No 82 210B complete with breakable plastic rod date labels and instruction sheet At a chandler you should ask for a Pains Wessex Breakthrough HRU with an EPIRB kit The HRU replacement procedure is as follows Rear E clip On the enclosure remove the R clip and pull the cover slowly off Remove the EPIRB and stow it in a dry place It will activate if wet Hold down the metal lever arm to take up the force of the spring Push the HRU back then upwards out of the slot in the lever arm When the rear clip disengages slowly release the lever arm The HRU with its breakable rod can now be lifted free and replaced Using pliers remove the rear E clip and slide off the old HRU Fit the new HRU over the new rod with its label facing outward Refit the washer and the rear E clip Ensure rod moves freely Mark the HRU with an expiry date 2 years into the future Slide the HRU into the slot in the lever arm and push lever arm down Engage rear washer into backplate by pushing back and sliding down Look under the spring and check that the washer i
27. n in the diagram above or you can use the plate itself at a drilling guide for the screws The recommended pilot hole size is 3mm maximum During vessel maintenance ensure the plate does not get painted over or cleaned down with strong degreasing solvents 16 8 ENCLOSURE INSTALLATION 8 1 Siting The enclosure should be mounted upright against a vertical bulkhead Alternately it may be mounted horizontally on a flat surface such as a cabin roof No other orientations are recommended yy 32 x Vi i If you have a float free EPIRB it is critical that you choose a position where the released EPIRB will not get trapped by overhangs rigging antennas etc should the vessel ever sink An expanse of flat surface is required to allow the enclosure lid to eject Use the list below to choose a suitable mounting position e Mount on the outside of the vessel s structure as high as possible e Mount close to the vessel s navigation position e Consider ease of access in an emergency AVOID e Positions with insufficient space for lid ejection and maintenance e Positions within 1m 3 of any compass equipment e Mounting within 2m 6 of any Radar antenna e Direct impact from waves e Siting where damage is likely Exhaust fumes chemical and oil sources 8 2 Mounting procedure The enclosure mounts against a flat surface using 4 fixing points See illustration for mounting dimensions or use the backplate of the enclosure as a m
28. r the coded message with local authorities READY button Press this key once to de activate the EPIRB Hold it down to run the built in self test which checks basic operation ON button Press this key to activate the EPIRB manually The key is protected by a sliding door which is fitted with a tamper seal Sea switch The two screw heads below the keys are sea switch contacts Submerge these in water to automatically activate the EPIRB Lanyard Pull the lanyard spool down to free it Use the cord to tether the EPIRB to a survival craft Never tie the EPIRB to your vessel 3 1 Wall bracket If you purchased the manually activated version m suffix this is normally supplied with a wall mounting bracket see section 7 The bracket is made from white plastic so it will not rust Its top section is sprung loaded so that one simple squeeze will quickly release the EPIRB allowing it to be carried to a liferaft The wall bracket should be sited in plain view near an emergency exit This bracket is more than just a stowage point it contains a magnet which disarms the EPIRB s sea switch If you do not stow the EPIRB in its bracket there is a risk of the EPIRB activating if it gets wet 3 2 Float free enclosure If you purchased the automatically activated version a suffix also known as the float free version then your EPIRB is supplied in a plastic enclosure see section 8 This is much more than just a protective housin
29. ribed in section 6 2 e Suppress its signal by removing the antenna and wrapping the EPIRB in metal foil as described in section 6 3 e Leave for 3 days until the battery is used up We do not recommend any other course of action However if it is absolutely necessary to fully disable an EPIRB by unplugging its battery proceed as follows This is a dangerous task and should only be performed by a qualified technician WARNING Risk of electric shock Proceed at your own risk no liability accepted e Take the EPIRB below decks into the dry e Locate a flat bladed screwdriver with a long reach e Unscrew and retain the front 4 sealing screws e Pull the lanyard out and remove the 2 hidden rear screws 5 e Do not as yet remove the sea contact screws wen e Lift the lens dome off Remove and retain the grey gasket e Avoid touching the circuit board and the glass strobe tube e Hold the hexagon shaped pillars and remove the sea screws e Use across headed screwdriver to remove the front screw e Grip the white plastic coil former and lift the circuit board up 3cm 1 e Using fingers unplug the white 4 way battery connector e The flashing will now cease e Collect all the parts and return them to your nearest service agent DANGER HIGH VOLTAGE Strobe Pull up on coil former Lens dome Hex Front screw Gasket Hidden screws Front sealing screws 12 TECHNICAL SPECIFICATION merit e ion s
30. s foreseeable Nothing shall limit McMurdo Limited s liability for death or personal injury caused by its negligence This warranty is to be interpreted under English law All enquiries relating to this warranty or Approved Service Agents should be sent to McMurdo Limited Silver Point Airport Service Road Portsmouth Hampshire PO3 5PB UK Telephone Int 44 0 23 9262 3900 Fax Int 44 0 23 9262 3998 Web www mcmurdo co uk Email sales mcmurdo co uk Record Serial No visible through dome 35 82 569 001 Issue 7
31. s fully engaged Slide EPIRB into D shaped foot on lever arm switches outermost Refit cover by engaging hole over rod and then snapping into place Refit R clip through top of rod On side of cover remove old HRU expiry date and mark new date Fitting HRU Spring Washer Breakable rod Engage washer here Lever arm 24 10 3 Battery replacement The EPIRB uses a 9V Lithium battery pack McMurdo type 82 570 Typically this will have to be replaced every 5 years The exact battery expiry date is marked on the rear of the EPIRB lens dome and if you have a full enclosure it is also marked on the outside of the enclosure The battery expiry date should be checked regularly You will need to replace the battery when e The expiry date has been reached or e The EPIRB has been used in an emergency situation or e A false activation exceeds 2 hours of use The battery is a one shot device It is not rechargeable or user replaceable Battery replacement must be carried out by a McMurdo approved service agent Lithium batteries have special disposal requirements Never incinerate a Lithium battery Never dispose of one at sea Your service agent will deal with battery disposal 10 4 Servicing All servicing must be carried out by a McMurdo approved service agent Always call your nearest agent and talk to their service department before returning suspect equipment You can find your nearest service agent from e The McMurdo web
32. ses When the rescue services get close this allows them to direction find on the signal To cater for searches at night the EPIRB has a bright flashing light that aids final visual location Battery expiry date Strobe Program point ON button READY under here button Sea contacts Lanyard If the programmed identity is a Radio Call Sign RCS then accuracy 5 limited to 5km 3 DESCRIPTION The EPIRB is a powerful self contained distress transmitter It is powered by a light weight Lithium battery that has a replacement interval of 5 years An EPIRB is intended to be a one shot device once activated it can operate for at least 48 hours It operates best while floating in water but it can also be operated while on board or in a Referring to the previous figure the key components of your EPIRB are as follows Antenna This is a flexible whip It must be near vertical when operating If the antenna gets bent gently straighten it out Strobe light This is the glass U tube visible through the clear lens dome When the EPIRB is activated this will flash every few seconds Red lamp Visible through the clear lens dome at the rear of the EPIRB This stays on or flashes to show you which mode you are in Green lamp This flashes when the GPS gets a position fix Program point A dimple in the clear dome through which your supplier can optically input the coded message unique to your EPIRB You must registe
33. site www mcmurdo co uk e Contacting McMurdo direct See warranty page e Contacting a McMurdo distributor If the EPIRB has to be returned the original packaging should be used if possible 10 5 Transportation Because it contains a Lithium battery the EPIRB may have special transportation requirements depending on local and international regulations in force at the time The battery pack contains approx 10 5gm of Lithium each battery pack contains 3 cells with 3 5 gm of Lithium in each Transport the EPIRB in compliance with applicable regulations for this weight of hazardous material For further information refer to the McMurdo website www mcmurdo co uk 10 6 GMDSS inspections If your vessel is subject to GMDSS regulations then you can expect to get regular visits from ship surveyors enforcing national legislation They will check the expiry dates and activate the EPIRB to prove that it really works and they will read the identity message stored inside the EPIRB to check that you have registered it properly Leisure vessels are not subject to these inspections However in some countries passenger and fishing vessels are covered by the legislation 29 26 11 FULLY DISABLING AN EPIRB In the unlikely event that your EPIRB refuses to turn off then it may have a fault Procedures for dealing with a faulty EPIRB are covered in section 6 on false alarms in simple terms you should do the following e De activate the EPIRB as desc
34. til it springs up Pull PAS forward Pull Lift up to down a ae CF 5 4 Releasing EPIRB from an enclosure If your EPIRB is fitted inside a full enclosure then follow the instructions below to release it manually from its enclosure 0 Pull Pull R clip cover from pin Pull EPIRB towards you 5 5 Manual activation If the vessel is not sinking but there is imminent danger then remove the EPIRB from its bracket and activate it manually as shown below Note that once activated it will flash immediately but it will not transmit a distress call for 2 minutes This gives you a chance to turn it off if you activated it in error Slide cover to left lt tamper seal 0 gt gt ee Locate switches on rear 0 will flash Once activated the EPIRB must have its antenna near upright and it must have a clear view of the sky for proper operation Lying it on its side or placing it next to a metal wall will impair its range and may fail to alert the rescue services Avoid handling the antenna as this will also impair performance 10 5 6 Deactivation If the EPIRB was activated by mistake or if the emergency ends then the EPIRB can Slide cover to right be reset back to its ready state as follows e Remove EPIRB from any water and dry its sea switch contacts Wait 8 seconds for sea switch to turn off If EPIRB is still flashing then it must have been turned on manually Press READY button e Slide the
35. will de activate the EPIRB and return it to its ready state When the button is released the strobe and the red amp green lamps will stop flashing Self test Pressing and holding the ready button for about 10 seconds will allow the built in self test to run When the button is held down the red lamp will come on for 4 seconds then go off During this time both the 121 5MHz homer and the 406MHz satellite transmitter make safe transmissions If both of these test transmissions arrive at the antenna with sufficient power then the strobe light will flash 3 times to tell you that all is well If the red lamp does not come on or the strobe light does not flash within 10 seconds then there is a fault the EPIRB should be taken to a service agent 4 3 Sea switch It is important to realise that the only time the EPIRB is completely off is when it is fitted in its mounting bracket or enclosure As soon as you take it out a magnetic switch activates and puts the EPIRB into its ready state It will not drain the battery in this state but it will turn on automatically if the sea switch contacts are bridged by water The sea contacts are the two exposed screw heads beside the rear switches Although you can control the EPIRB manually with the READY and ON switches the sea switch overrides any manual settings For the manual switches to operate properly the EPIRB must first be dry so that the sea switch is de activated To ensure t
Download Pdf Manuals
Related Search