13" 4A String Trimmer Manual (English)
Contents
1. Install the new spool so that the strings and slots align with the eyelets in the string head Thread the strings into the eyelets Pull the strings extending from the string head so the string releases from the slots in the spool e Reinstall the spool retainer by depressing tabs into slots and pushing down until spool retainer clicks into place WIND CLOCKWISE RETAINER SPOOL STRING REPLACEMENT See Fig 12 13 e Unplug the string trimmer Remove the spool from the string head NOTE Keep the spring attached to the spool Remove any old string remaining on the spool e Cut two pieces of string each being approximately 9 ft 2 7 m long Use only 065 in 1 65 mm diameter monofilament string Insert the first string into the anchor hole in the upper part of the spool Wind the first string around the upper part of the spool counterclockwise as shown by the arrows on the spool Place string in the slot on upper spool flange leaving about 6 in 152 mm extended beyond the slot Do not overfill After winding the string there should be at least 1 4 in 6 mm between the wound string and the outside edge of the spool Repeat above step with second string using the bottom part of spool Do not overfill Replace the plastic retainer spool and the spool retainer Refer to Spool Replacement earlier in this manual 18 MAINTENANCE STORING THE TRIMMER Depress telescoping boom coupler and set2. and understand completely the operator s manual If you do not understand the warnings and instructions in the operator s manual do not use this product Call GREENWORKS customer service for assistance AWARNING The operation of any power tool can result in foreign objects being thrown into your eyes which can result in severe eye damage Before beginning power tool operation always wear safety goggles or safety glasses with side shields and when needed a full face shield We recommend Wide Vision Safety Mask for use over eyeglasses or standard safety glasses with side shields Always use eye protection which is marked to comply with ANSI Z87 1 SAVE THESE INSTRUCTIONS 7 ELECTRICAL DOUBLE INSULATED Double insulation is a concept in safety in electric power tools which eliminates the need for the usual threewire grounded power cord All exposed metal parts are isolated from the internal metal motor components with protecting insulation Double insulated tools do not need to be grounded A WARNING The double insulated system is intended to protect the user from shock resulting from a break in the tool s internal insulation Observe all normal safety precautions to avoid electrical shock NOTE Servicing of a product with double insulation requires extreme care and knowledge of the system and should be performed only by a qualified service technician For service we suggest you return the tool to yo
3. at shortest setting Clean all foreign material from the trimmer Store it in a place that is inaccessible to children Keep away from corrosive agents such as garden chemicals and de icing salts TROUBLESHOOTING PROBLEM Strings will not advance when using the Auto Feed Head Grass wraps around drive shaft housing and string head Motor fails to start when switch trigger is depressed POSSIBLE CAUSE 1 Strings are welded to themselves 2 Not enough string on spool 3 Strings are worn too short 4 Strings are tangled on spool 1 Cutting tall grass at ground level 1 Power cord is not plugged in or connection is loose 2 Household circuit breaker is tripped 19 SOLUTION 1 Lubricate with silicone spray 2 Install more string Refer to String Replacement earlier in this manual 3 Pull strings while alternate ly pressing down on and releasing spool retainer 4 Remove strings from spool and String Replacement earlier in this manual 1 Cut tall grass from the top down to prevent wrapping 1 Plug in the power cord 2 Check circuit breaker LIMITED FOUR YEAR WARRANTY greenworks GREENWORKS hereby warranties this product to the original purchaser with proof of purchase for a period of four 4 years against defects in materials parts or workmanship GREENWORKS at its own discretion will repair or replace any and all parts found to be defective throug
4. body and the string trimmer Any contact with the string trimmer cutting head while operating can result in serious personal injury ADVANCING STRINGS NOTE The trimmer is equipped with an auto feed head Bumping the head to try to advance the line will damage trimmer and void warranty With the trimmer running release the switch trigger e Wait two seconds and press the switch trigger NOTE The strings will extend approximately 1 4 in with each stop and start of the switch trigger until the strings reach the length of the grass deflector blade e Resume trimming ADVANCING THE STRINGS MANUALLY Disconnect the string trimmer from the power supply then push the spool retainer button in while pulling on strings to manually advance the strings CUT OFF BLADE This trimmer is equipped with a cut off blade on the grass deflector For best cutting advance strings until they are trimmed to length by the cut off blade Advance strings whenever you hear the engine running faster than normal or when trimming efficiency diminishes This will maintain best performance and keep strings long enough to advance properly 14 OPERATION CUTTING TIPS See Fig 7 Keep the trimmer tilted toward the area being cut this is the best cutting area The string trimmer cuts when passing the unit from left to right This will avoid throwing debris at the operator Avoid cutting in the dangerous area shown in figure 8 e Use
5. comply could result in accidental starting and possible serious personal injury STARTING STOPPING THE TRIMMER See Fig 4 5 Attach the outlet end of an extension cord to the plug on the rear of the string trimmer NOTE Use only approved outdoor extension cords Route the extension cord through the slot located on the rear of the string trimmer housing and place underneath the cord retainer To start the string trimmer press the switch trigger To stop the string trimmer release the switch trigger If any parts are damaged or missing please call 1 888 909 6757 for assistance 12 ASSEMBLY SWITCH TRIGGER FRE ATTACH OUTLET END OF EXTENSION CORD OUTLET HERE END Fig 4 OPERATING THE TRIMMER See Fig 6 PROPER OPERATING POSITION FOLLOW THESE TIPS WHEN USING THE STRING TRIMMER Hold the trimmer with your right hand on the rear handle and your left hand on the front handle Keep a firm grip with both hands while in operation 13 ASSEMBLY e Trimmer should be held at a comfortable position with the rear handle about hip height e Cut tall grass from the top down This will prevent grass from wrapping around the shaft housing and string head IF GRASS BECOMES WRAPPED AROUND THE STRING HEAD Stop the trimmer e Unplug the string trimmer e Remove the grass OPERATION AWARNING Always hold the string trimmer away from the body keeping clearance between the
6. ECTRICAL Ampere rating on tool faceplate MINIMUM GAUGE FOR EXTENSION CORDS AWG WHEN USING 120V ONLY Amp Rating Total Length of Cord in Feet meters More Than Not More Than 25 7 6 m 50 15 m 100 30 4m 150 45 7 m 0 6 18 16 16 14 6 10 18 16 14 12 10 12 16 16 14 12 12 16 14 12 Not Recommended When working with the tool outdoors use an extension cord that is designed for outside use This is indicated by the letters WA on the cord s jacket Before using an extension cord inspect it for loose or exposed wires and cut or worn insulation AWARNING KEEP THE EXTENSION CORD CLEAR OF THE TINES AND WORKING AREA POSITION THE CORD SO THAT IT WILL NOT GET CAUGHT ON LUMBER TOOLS OR OTHER OBSTRUCTIONS WHILE YOU ARE WORKING WITH A CULTIVATOR FAILURE TO DO SO CAN RESULT IN SERIOUS PERSONAL INJURY AWARNING CHECK EXTENSION CORDS BEFORE EACH USE IF DAMAGED REPLACE IMMEDIATELY NEVER USE TOOL WITH A DAMAGED CORD SINCE TOUCHING THE DAMAGED AREA COULD CAUSE ELECTRICAL SHOCK RESULTING IN SERIOUS INJURY FEATURES ROTATING REAR HANDLE FRONT HANDLE SWITCH TRIGGER CORD RETAINER TELESCOPING BOOM DEFLECTOR KNOW YOUR STRING TIMMER See Fig 1 The safe use of this product requires an understanding of the information on the tool and in this operator s manual as well as a knowledge of the project you are attempting Before use of this product familiarize yourself with all
7. GREENWORKS 20 PARTS 1 1213 14 15 US 21 PARTS LIST ITEM NO PART NO DESCRIPTION 34101178 6 Switch board 33401178 Switch spring 36303152 Switch 3220313 Screw 31300178 6 Handle 3640185 Connector 3410182 Wall 3220505 Screw 3410302 Board 3220905 Screw 3650135 B Terminal 34115178 6 Auxiliary handle 34202178 Rubber 32900178 Screw 32200178 Corner bolts 36502161 Terminal 34903161 Sheath 36900178 Power cable 3220313 Screw 3130185A 6 Motor cover 33301 176 6 Shaft 34201178 Rubber 3411105 Sheath 3220505 Screw 3410302 Board 3650135 B Terminal 36101178 Motor 33202178 Bushings 31105178 Fan 3290105 Nut 3340646 Spring 3410368 Button 3290106 Nut 3412505 Wall 31104178 Spool 34108178A 6 Spool cover 3410385 6 Guard 33300337 Rest 3220323 Screw 33301178 Steel structure 3220811 Screw 3290805A Nut afal oa po a a a a a a a 3 a 3 3 3 SJ 3 po 3 po S SN Sa po po SB a 3 SS Sa po Sa ro a 3 a oo a a a NOTES 23 greenworks TOLL FREE HELPLINE 1 888 90WORKS 888 909 6757 Rev 03 06 24 11 ae Printed in China on 100 Recycled Paper
8. If the plug does not fit fully into the extension cord reverse the plug If the plug still does not fit obtain a correct polarized extension cord A polarized extension cord will require the use of a polarized wall outlet This plug will fit into the polarized wall outlet only one way If the plug does not fit fully into the wall outlet reverse the plug If the plug still does not fit contact a qualified electrician to install the proper wall outlet Do not change the equipment plug extension cord receptacle or extension cord plug in any way Avoid body contact with grounded surfaces such as pipes radiators ranges and refrigerators There is an increased risk of electric shock if your body is grounded Avoid Dangerous Environments Don t expose power tools to rain or wet conditions Water entering a power tool will increase the risk of electric shock 3 IMPORTANT SAFETY INSTRUCTIONS AWARNING To reduce the risk of electric shock Use outdoor extension cords marked W A W SW A SOW A STW A STOW A SJW A SJTW A or SUTOW A These cords are rated for outdoor use and reduce the risk of electric shock Ground Fault Circuit Interrupter GFCI protection should be provided on the circuit s or outlet s to be used for the gardening appliance Receptacles are available having built in GFCI protection and may be used for this measure of safety Use Right Appliance Do not force tool Use the correct tool for your a
9. greenworks 13 4A ELECTRIC STRING TRIMMER 21212 M A B 218549 Owner s Manual TOLL FREE HELPLINE 1 888 90WORKS 888 909 6757 A Read all safety rules and instructions carefully before operating this tool CONTENTS CON OM S nacida add tdi ds 2 SPeCifiCatiOns iii ind iaaa ada R TA RRA 2 Important Safety InstrUctiON Sion tl da 3 5 Symbols Electra asi 8 9 A O 10 ASSeMD ly cricca A a a a A a Na aAA AE AEREE 11 14 Operator E cea re cere ne a a a a E AT AERE 14 16 Maintenance 17 19 Troubleshooting etorri idad a 19 Warranty sti lid 20 Parts Parts Listin 21 22 SPECIFICATIONS 13 4A ELECTRIC STRING TRIMMER Feed POr ana 0 065 Auto Feed ALET I ah ET T 5 2lb 2 3kg Replacement Spool 29082 fy OM rn CORDED OR CORDLESS ZERO CARBON FOOTPRINT IN THE YARD IMPORTANT SAFETY INSTRUCTIONS A WARNING Read and understand all instructions Failure to follow all instructions listed below may result in electric shock fire and or serious personal injury For safe operation read and understand all instructions before using this product Follow all safety instructions Failure to follow all safety instructions listed below can result in serious personal injury Do not allow children or untrained individuals to use this unit Check the work area before each use Remove all objects such as rocks broken glass nails wire or string which can be thro
10. h defects or other reproductive harm Some examples of these chemicals are e Lead from lead based paints e Crystalline silica from bricks and cement and other masonry products and e Arsenic and chromium from chemically treated lumber Your risk from these exposures varies depending on how often you do this type of work To reduce your exposure to these chemicals work in a well ventilated area and work with approved safety equipment such as those dust masks that are specially designed to filter out microscopic particles SAVE THESE INSTRUCTIONS 5 SYMBOLS Some of the following symbols may be used on this product Please study them and learn their meaning Proper inter pretation of these symbols will allow you to operate the product better and safer SYMBOL NAME DESIGNATION EXPLANATION Voltage V W Alternating Current Type of current Direct Current Type or a characteristic of current a Class II Construction Double insulated construction Wet Conditions Alert Do not expose to rain or use in damp locations Read The Operator s Manual To reduce the risk of injury user must read and understand operator s manual before using this product A Safety Alert Precautions that involve your safety Keep Bystanders Away Keep all bystanders at least 50 ft away Eye Protection Always wear safety goggles or safety glasses with side shields and as necessary a full face shield when operating this prod
11. h normal use free of charge to the customer This warranty is valid only for units which have been used for personal use that have not been hired or rented for industrial commercial use and that have been maintained in accordance with the instructions in the owners manual supplied with the product from new Battery carries a one 1 year warranty against defects in workmanship and materials Batteries must be charged in accordance with the operator s manuals directions and regulations in order to be valid ITEMS NOT COVERED BY WARRANTY 1 Any part that has become inoperative due to misuse commercial use abuse neglect accident improper maintenance or alteration or 2 The unit if it has not been operated and or maintained in accordance with the owner s manual or 3 Normal wear except as noted below 4 Routine maintenance items such as lubricants blade sharpening 5 Normal deterioration of the exterior finish due to use or exposure GREENWORKS HELPLINE 1 888 90WORKS Warranty service is available by calling our toll free helpline 9am to 59m EST Monday Friday at 1 888 909 6757 1 888 90WORKS TRANSPORTATION CHARGES Transportation charges for the movement of any power equipment unit or attachment are the responsibility of the purchaser It is the purchaser s responsibility to pay transportation charges for any part submitted for replacement under this warranty unless such return is requested in writing by
12. le metal wire rope or the like To install any other brand of cutting head to this string trimmer can result in serious personal injury e Never operate unit without the grass deflector in place and in good condition Check damaged parts Before further use of the tool a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function Check for alignment of moving parts binding of moving parts breakage of parts mounting and any other conditions that may affect its operation A guard or other part that is damaged must be properly repaired or replaced by an authorized service center to avoid risk of personal injury e Maintain a firm grip on both handles while trimming Keep string head below waist level Never cut with the string head located over 30in or more above the ground Store idle appliances When not in use string trimmer should be stored indoors in a dry locked place out of the reach of children 4 IMPORTANT SAFETY INSTRUCTIONS Make sure your extension cord is in good condition When using an extension cord be sure to use one heavy enough to carry the current your product will draw A wire gauge size A W G of at least 16 is recommended for an extension cord 50 feet or less in length A cord exceeding 100 feet is not recommended If in doubt use the next heavier gauge The smaller the gauge number the heavier the cord An undersized c
13. operating features and safety rules CORD RETAINER A convenient cord retainer helps keep the extension cord connection secure during string trimmer operation EDGER GUIDE The easily mounted edger guide allows the string trimmer to perform as an edger FRONT HANDLE The string trimmer is equipped with a front handle assembly for ease of operation and to prevent loss of control GRASS DEFLECTOR The trimmer includes a grass deflector that helps protect from flying debris ROTATING REAR HANDLE The rotating rear handle on the string trimmer can be locked in two different positions for ease of use when edging TELESCOPING BOOM The string trimmer can be adjusted to different extension points for ease of use 10 ASSEMBLY UNPACKING This product requires assembly Carefully remove the product and any accessories from the box Make sure that all items listed in the packing list are included e Inspect the product carefully to make sure no breakage or damage occurred during shipping Do not discard the packing material until you have carefully inspected and satisfactorily operated the product If any parts are damaged or missing please call 1 888 909 6757 for assistance PACKING LIST Trimmer Assembly e Grass Deflector Assembly with Screw Operator s Manual A WARNING If any parts are damaged or missing do not operate this product until the parts are replaced Failure to heed this warning could re
14. ord will cause a drop in line voltage resulting in loss of power and overheating Never use blades or flailing devices Unit is designed for line trimmer use only Use of any other accessories or attachments will increase the risk of injury Inspect area to be cut Remove objects rocks broken glass nails wire string etc which can be thrown or become entangled in cutting head e Keep the air vents clean and free of debris to avoid overheating the motor Clean after each use Stop the unit and disconnect the power source when not in use Carry the unit with the motor stopped Store unplugged and out of the reach of children Do not hang unit so that the switch trigger is depressed Do not use multiple cords Do not abuse the cord Never carry the unit by the extension cord or yank extension cord to disconnect unit e Keep the extension cord clear of operator and obstacles at all times Do not expose cords to heat oil water or sharp edges If the power supply cord is damaged it must be replaced only by the manufacturer or by an authorized service center to avoid risk e Save these instructions Refer to them frequently and use them to instruct others who may use this power tool If you loan someone this power tool loan them these instructions also AWARNING Some dust created by power sanding sawing grinding drilling and other construction activi ties contains chemicals known to cause cancer birt
15. pplication The correct tool will do the job better and safer at the rate for which it is designed Do not operate the equipment while barefoot or when wearing sandals or similar lightweight footwear Wear protective footwear that will protect your feet and improve your footing on slippery surfaces Do not overreach Keep firm footing and balance Over reaching can result in loss of balance e Avoid Accidental Start Do not carry plugged in appliance with finger on trigger Be sure the switch trigger is not en gaged before plugging in Do not use tool if switch trigger does not turn it on or off Any tool that cannot be controlled with the switch trigger is dangerous and must be repaired e Disconnect appliance from power source before storing servicing changing accessories such as cutting line Such preventive safety measures reduce the risk of starting the tool accidentally Use only identical manufacturer s replacement parts and accessories Use of any other parts may create a hazard or cause product damage e Maintain appliance with care Replace string head if cracked chipped or damaged in any way Be sure the string head is properly installed and securely fastened Failure to do so can cause serious injury Make sure all guards straps deflectors and handles are properly and securely attached Use only the manufacturer s replacement string in the cutting head Do not use any other cutting attachment for examp
16. sult in serious personal injury AWARNING Do not attempt to modify this product or create accessories not recommended for use with this product Any such alteration or modification is misuse and could result in a hazardous condition leading to possible serious personal injury AWARNING Do not connect to power supply until assembly is complete Failure to comply could result in accidental starting and possible serious personal injury ATTACHING GRASS DEFLECTOR See Fig 2 3 1 Remove supplied screw with a phillips screwdriver from the trimmer head 2 Fit the grass deflector into the slots on trimmer head 3 Turn counterclockwise to lock grass deflector into place 4 Line up the screw hole in the grass deflector with the center hole in the trimmer head 5 Install supplied screw and tighten by turning clockwise with a phillips screwdriver ma ma ASSEMBLY OVER HEAD IN AND 22 4 TURN COUNTER CLOCKWISE If any parts are damaged or missing do not operate this product until the parts are replaced Failure to heed this warning could result in serious personal injury A WARNING Do not attempt to modify this product or create accessories not recommended for use with this product Any such alteration or modification is misuse and could result in a hazardous condition leading to possible serious personal injury A WARNING Do not connect to power supply until assembly is complete Failure to
17. the tip of the string to do the cutting do not force string head into uncut grass e Wire and picket fences cause extra string wear even breakage Stone and brick walls curbs and wood may wear strings rapidly Avoid trees and shrubs Tree bark wood moldings siding and fence posts can easily be damaged by the strings DANGEROUS CUTTING AREA DIRECTION OF BEST CUTTING ROTATION Moda AREA cid TELESCOPING BOOM See Fig 8 The boom can be extended or shortened for ease of use e Unplug the string trimmer Unscrew telescoping boom coupler and slide to desired position Tighten telescoping boom coupler ROTATING REAR HANDLE See Fig 9 e Unplug the string trimmer Pull up edging coupler and turn handle end counterclockwise Release edging boom coupler when handle has been rotated 180 15 OPERATION TELESCOPING COUPLER J HANDLE PULL UP EDGING COUPLER TO ROTATE EDGING See Fig 9 11 The rotating handle can be used in combination with the edger guide for edging sidewalks and walkways To use the edger guide flip down from it s stored position EDGER GUIDE Fig 10 16 MAINTENANCE AWARNING When servicing use only identical replacement parts Use of any other parts may create a hazard or cause product damage AWARNING Always wear safety goggles or safety glasses with side shields during power tool operation or when blowing dust If operation is dust
18. uct Long Hair Failure to keep long hair away from the air inlet could result in personal injury Loose Clothing Failure to keep loose clothing from being drawn into air intake could result in personal injury Ricochet Thrown objects can ricochet and result in personal injury or property damage Sharp Blade Danger Keep hands and feet away from blade No Hand Symbol Failure to keep your hands away from the blade will result in serious personal injury Sy MBOLS The following signal words and meanings are intended to explain the levels of risk associated with this product SYMBOL SIGNAL MEANING DANGER Indicates an imminently hazardous situation which if not avoided will result in death or serious injury WARNING Indicates a potentially hazardous situation which if not avoided could result in death or serious injury CAUTION Indicates a potentially hazardous situation which if not avoided may result in minor or moderate injury CAUTION Without Safety Alert Symbol Indicates a situation that may result in property damage SERVICE Servicing requires extreme care and knowledge and should be performed only by a qualified service technician For service we suggest you return the product to your nearest AUTHORIZED SERVICE CENTER for repair When servicing use only identical replacement parts AWARNING To avoid serious personal injury do not attempt to use this product until you read thoroughly
19. ur nearest authorized service center for repair Always use original factory replacement parts when servicing ELECTRICAL CONNECTION This product has a precision built electric motor It should be connected to a power supply that is 120 volts AC only normal household current 60 Hz Do not operate this product on direct current DC A substantial voltage drop will cause a loss of power and the motor will overheat If your product does not operate when plugged into an outlet double check the power supply GFCI Ground Fault Circuit Interrupter GFCI protection should be provided on the circuit s or outlet s to be used for the product Receptacles are available having built in GFCI protection and may be used for this measure of safety EXTENSION CORDS When using a power product at a considerable distance from a power source be sure to use an extension cord that has the capacity to handle the current the product will draw An undersized cord will cause a drop in line voltage resulting in overheating and loss of power Use the chart to determine the minimum wire size required in an extension cord Only round jacketed cords listed by Underwriter s Laboratories UL should be used When working outdoors with a product use an extension cord that is designed for outside use This type of cord is designated with WA on the cord s jacket Before using any extension cord inspect it for loose or exposed wires and cut or worn insulation EL
20. wn or become entangled in the machine e Wear eye protection which is marked to comply with ANSI Z87 1 when operating this product Use Safety Glasses Always use face or dust mask if operation is dusty Always wear safety glasses with side shields Everyday glasses have only impact resistant lenses They are NOT safety glasses Following this rule will reduce the risk of eye injury Use face mask if operation is dusty Dress Properly Use rubber gloves and substantial footwear is recommended when working outdoors e Wear heavy long pants boots and gloves Do not wear loose fitting clothing short pants or go barefoot Do not wear jewelry of any kind Secure long hair above shoulder level to prevent entanglement in moving parts Keep children away Keep all bystanders children and pets at least 50 ft away Stay alert Do not operate this unit when you are tired ill or under the influence of alcohol drugs or medication Do not operate in poor lighting Keep all parts of your body away from any moving part Do not operate power tools in explosive atmospheres such as in the presence of flammable liquids gases or dust Power tools create sparks which may ignite the dust or fumes To reduce the risk of electric shock this tool has a polarized plug one blade is wider than the other and will require the use of a polarized extension cord The plug will fit into a polarized extension cord only one way
21. y also wear a dust mask AWARNING Before inspecting cleaning or servicing the unit stop the motor wait for all moving parts to stop and disconnect from power supply Failure to follow these instructions can result in serious personal injury or property damage GENERAL MAINTENANCE Avoid using solvents when cleaning plastic parts Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use Use clean cloths to remove dirt dust oil grease etc AWARNING Do not at any time let brake fluids gasoline petroleum based products penetrating oils etc come in contact with plastic parts Chemicals can damage weaken or destroy plastic which may result in serious personal injury Periodically clean all foreign material from the trimmer head vents You can often make repairs described here For other repairs have the trimmer serviced by an authorized service dealer SPOOL REPLACEMENT See Fig 12 Use only 065in diameter monofilament string Use original manufacturer s replacement string for best performance e Unplug the string trimmer Push in tabs on side of spool retainer Pull spool retainer up to remove Remove spool To install the new spool make sure the two strings are captured in the slots opposite each other on the new spool Make sure the end of each string is extended approximately 6in beyond each slot 17 MAINTENANCE
Download Pdf Manuals
Related Search