B-400-1COAX-HDIR Manual
Contents
1. COAX HDIR Transmitter and Receiver e 4 Mounting Screws e 8 Rubber Feet 2 5V Power Supply Units e 1 User manual e 1 IR Adapter Cable INTRODUCTION The B 400 1COAX HDIR extends HDMI over a single coax allowing video and audio transmission up to 400 ft In addition the B 400 1COAX HDIR is equipped with bi directional IR pass through allowing users to send IR control up to a distance of 400ft making IR control possible without any additional wires FEATURES e HDMI 1 3a compliant This unit does NOT support 3D e HDCP compliant e Single RG6 3G Quadshield Solid Copper 75 ohm coaxial cable extends the transmission range up to 400 ft from the HDMI source and supports up to 1080p60 with 24 bit color depth Up to 7 1 channel audio supported including Dolby Digital DTS and PCM This unit does NOT support Dolby True HD DTS HD or LPCM e Video resolutions supported are 480i 720p 1080i and 1080p This unit does NOT support 480p e Bi directional IR with IR Adapter Cable to connect to control systems e Wall mountable housing design for easy installation Note The transmission distance is subject to the quality of installed coax cable source device and display Higher resolutions and longer transmissions require high quality cabling RG6 3G Solid copper quadshield 75 Ohm cable and 75 ohm BNC connectors are recommended Any connections along the transmission path will reduce the transmission performance INPUT2. BINARY snap OEE gt gt Erini with i Pace Through B 400 1COAX HDIR gach WELCOME TO THE BINARY BRAND OF PRODUCTS This product is engineered to provide years of exceptional reliability Binary is one of the most highly regarded brands available today We appreciate your business and we stand committed to providing our customers with the highest degree of quality and service in the industry IMPORTANT SAFETY INSTRUCTIONS The B 400 1COAX HDIR HDMI over single coax extender with IR pass through has been tested for conformity to safety regulations and requirements and has been certified for international use However like all electronic equipment the B 400 1COAX HDIR should be used with care Please read and follow the safety instructions to protect yourself from possible injury and to minimize the risk of damage to the unit Follow all instructions and warnings marked on this unit e Do not attempt to service this unit yourself except where explained in this manual e Provide proper ventilation and air circulation and do not use near water e Keep objects that might damage this unit at a safe distance and ensure that the placement of this unit is on a stable surface e Use only the power adapter power cords and connection cables designed for this unit e Do not use liquid or aerosol cleaners to clean this unit Always unplug the power to the device before cleaning PACKAGE CONTENTS 1 B 400 1
3. EM Test the connections SEREN IR OUT 12V Ground IR RECEIVER not included Episode IR SM 3660 or Episode IR TT 3660 Coax Cable NO CONNECTION GROUND SLEEVE ml b 3 OC RECEIVER Fi amp MINI MONO CABLE not included Binary B3 MonoMini 5 B3 MonoMini 1 or B3 MonoMini 2 oap Weert LOS IR ADAPTER CABLE included IR FLASHER not included Episode IRF 1 or Episode IRF 2 INSTALLATION 1 Select the appropriate mode see transmitter section or learn the EDID from the display to the transmitter see EDID learning Section 2 Connect a HDMI source such as a Blu ray Disc player to the transmitting unit 1 Meter or shorter HDMI cable is recommended 3 Connect a HDMI display such as a LCD TV to the receiving unit 1 Meter or shorter HDMI cable is recommended 4 Connect IR Flashers Receivers to both transmitting and receiving units 5 Connect a high quality 75 ohm coax cable with 75 ohm BNC terminations between the units ensuring the cable is tightly connected WARNING Do not make termination to the coax while connected to the extender 6 Plug in the 5V DC power supply units to the power jack of both the transmitting and receiving units CAUTION All terminations to the coax cable should be made before connecting to the extender Do not make coax terminations if one end of the coax is connected to either end of the exte
4. IN Connect a high quality coaxial cable to this BNC and link to the transmitting unit 11 HDMI OUT Connects to a HDMI display with a HDMI male to male cable 1 meter or shorter HDMI interconnect cable is recommended 12 LED Orange Power but not receiving a signal on the COAX IN Green Power and signal present on the coax cable 13 Screw locking power jack Connect the provided 5V DC power supply EDID LEARNING 1 Ensure DIP Switches 1 and 2 are set to On On W 2 Connect the HDMI display to HDMI IN on the Transmitter with a HDMI cable 3 Power on the Transmitter by connecting the 5V Power Supply The LED will be orange until the unit learns the EDID 4 After the LED turns GREEN the EDID Learning procedure is complete The LED will remain green until the HDMI cable is removed 5 Unplug the HDMI cable from the display and follow the installation instructions DO NOT change the DIP switches or the EDID information will be lost IR PASS THROUGH IR signals can be passed from the transmitter to the receiver over the Coax cable Each unit will need both an IR Receiver and an IR Flasher sold separately This allows the units to receive IR information and transmit it Receiver Flasher COAX OUT y CAUTION Incorrect connection of the IR Flasher and Receiver may result in IR extender failure Check carefully before plugging in the IR extender to the respective
5. IR sockets Warranty will not cover the damage NOTE This product was specifically engineered for Episode IR products Use of the following products is highly recommended items not included IR Flasher IR Receiver Mini Mono Cable Episode IRF 1 Episode IR SM 3660 Binary B3 MonoMini 5 or Episode IRF 2 or Episode IR TT 3660 B3 MonoMini 1 or B3 MonoMini 2 SPECIFICATIONS IR FLASHER 12V DC Sleeve Grounding IR Signal Tip Ring 20 60 kHz IR Signal Tip Grounding 20 60 kHz Ring IR RECEIVER nT IR ADAPTER CABLE FOR CONTROL SYSTEMS INCLUDED U IR Signal Tip i i i Grounding IR Signal Tip Grounding 12V DC Sleeve 20 60 kHz Ring Sleeve IR INTEGRATION WITH A CONTROL SYSTEM The IR Receiver connection on the Transmitter is designed to operate with Episode IR products When connecting the Transmitter to an IR Remote Control System or Home Automation system to control the display from the control system it is necessary to convert the connection from a stereo 3 5mm 1 8 cable to a mono 3 5mm 1 8 cable and eliminate 12VDC Included in the box is an IR Adapter Cable to make this connection very simple First connect the male end of the IR Adapter Cable to the IR Receiver jack on the Transmitter Next connect a mono 3 5mm 1 8 cable from the female end of the IR Adapter Cable to the control system CONTROL SYST
6. PANEL OUTPUT PANEL Orange Power Green Power Signal TRANSMITTER NOTE Transmission distance up to 400 feet at 1080p 24 Bit 1 HDMI IN Connects to a HDMI source with a HDMI male to male cable 1 meter or shorter HDMI interconnect cable is recommended 2 LED Orange Power but no HDMI input signal Green Power and HDMI signal present 3 MODE 2 pin DIP Switch Please see table below for detailed information Pin 1 Pin 2 EDID MODE Up to 1080p 60 with 7 1 Dolby Digital DTS PCM audio support Also supports 1080p 30 1080p 24 1080i 60 720p 60 4801 60 Up to 720p 60 with Stereo audio support Also supports 1080p 30 1080p 24 1080i 60 480i 60 Up to 1080p 60 with Stereo audio support Also supports 1080p 30 1080p 24 1080i 60 720p 60 4801 60 ON W ON W EDID Learning Mode Note 480p is not supported OFF M OFF A ON WW OFF M OFF A ON 4 COAX OUT Connect a high quality coaxial cable to this BNC and link to the receive unit 5 IR Receiver Infrared 3 5mm jack for an IR receiver or IR adapter cable for connection to a control system 6 IR Flasher Infrared 3 5mm jack for an IR flasher 7 Screw locking power jack Connect the provided 5V DC power supply INPUT PANEL OUTPUT PANEL IR IR Receiver Flasher COAX IN 8 IR Receiver Infrared 3 5mm jack for an IR receiver 9 IR Flasher Infrared 3 5mm jack for an IR flasher 10 COAX
7. nder SPECIFICATIONS HDMI over Coax transmission range Full HD 1080p 24 bit color 400ft Surround sound up to 7 1ch or stereo digital audio Does NOT support Dolby True HD DTS HD or LPCM Input TMDS Signal 1 2 Volts peak to peak Input DDC Signal 5 Volts peak to peak TTL 1 Human body 19kV air gap discharge amp 12kV contact discharge 2 Core chipset 4kV Audio Support ESD Protection PCB Stack Up 6 layer board impedance control differential 1000 single 500 IR Pass Through Bi directional E e ae IR Remote Control Carrier frequency 20 60kHz E TX and RX each 3 x 3 x 1 2 20 90 RH no condensation Note Specifications are subject to change without notice Dimensions and weight are approximate WARRANTY 2 Year Limited Warranty This Binary Product has a Two Year Limited Warranty This warranty includes parts and labor repairs on all components found to be defective in material or workmanship under normal conditions of use This warranty shall not apply to products which have been abused modified or disassembled Products to be repaired under this warranty must be returned to SnapAV or a designated service center with prior notification and an assigned return authorization number RA For Technical Support 1 866 838 5052
Download Pdf Manuals
Related Search