4000CL-O User Manual
Contents
1. 4 to select VTR c Assign a Peripheral Device Address for that VTR from 0 to 23 by entering the desired address using the numeric keypad Press DEL to turn off the device Any address greater than 23 turns the device off d Select the next VTR and assign a Peripheral Device Address for it e When done press ESC to exit MENU mode 4 Configure the production switcher Enable the Peripheral Bus Enable the Peripheral Device Addresses assigned to the ST300 Enable the appropriate Learn Recall levels Enable the Timeline or Recall Trigger function 4 VIDEO SERVER SETUP Refer to Quantel Operators Manual Set serial ports to the following format Baud Rate 9600 Parity None Data Bits 8 Stop Bits 1 6 4000CL Q 400 Clip Fast Access System Quantel Protocol PBIO Option 7 LOAD A CLIP Select a VTR by press VTR 1 VTR 2 VTR 3 or VTR 4 Press CLIP LIST to view the list of CLIP IDs that are resident on the Video Server The CLIP LIST indicator will turn on Press CREATE to create and load a new clip Creating a clip is described in the CREATE NEW CLIPS section OR Turn the Wheel to view the existing CLIP IDs on the video server Turn the Wheel clockwise to scroll forward or counter clockwise to scroll backward through the list of available CLIPs Backward scrolling is limited to the last 10 CLIP IDs viewed OR Manually enter a CLIP ID using the ST300 numeric keypad or PC keyb2. CUE LIST FUNCTION 1 To Transmit Cue Points to the ST300 a Connect the VTR4 connector on the rear of the ST300 to the VTR4 connector of the receiving ST300 using an RS422 9 pin cable with TX and RX lines crossed A turnaround cable b Press MENU and scroll the Wheel to Transmit CUE List YES Enter Exit ESC c Press ENTER to start transmitting The Display shows Waiting to transmit on the first line d When the Receiver is ready transfer starts automatically The Display now shows Transmitting cuelist e After the transfer is over the display shows Transfer is over for one second and then shows Waiting to transmit again f Connect another ST300 to transmit the list again OR Press ESC twice to exit the MENU mode 2 To Transmit Cue Points to the PC a Connect the VTR4 connector on the back of the ST300 to one of the COM ports on the PC using a RS422 to RS232 adapter b Repeat steps b f of the TRANSMIT CUE POINTS to the ST300 section 4000CL Q 400 Clip Fast Access System Quantel Protocol PBIO Option 13 b RECEIVE CUE LIST FUNCTION The RECEIVE CUELIST function allows you to receive your list of Cue Points from a PC or from another ST300 Transfer to a PC requires OpSuite 3 0 software which runs on a Windows based computer Contact DNF Controls for more information 1 To Receive Cue Points from the ST300 a Connect the VTR4 connector on the back of the ST300 fr
3. VTRs cues the Clip to the Learned time then restores the Learned GANG mode Learn amp Recall may also be done directly from the ST300 without the production switcher The Trigger function on the production switcher puts the selected VTRs into Play Stop Recue or other available modes The SHOTLIST contains up to 400 CLIP IDs and provides fast access to existing video clips stored in non volatile memory in the ST300 Remotely view the CLIP IDs that exist in the Video Server under control Any clip in the SHOTLIST can be quickly loaded by simply entering the associated 3 digit number of its location then pressing LOAD Press PLAY to play the clip Press RECUE to recue to the beginning of the clip DEFINITIONS Throughout this document VTR DDR VDR amp Video Server will be referred to collectively as Video Server The ST300 S SM is referred to as ST300 Words surrounded by brackets for example ENTER are keys on the ST300 XXX XXX means hold the two keys down simultaneously XXX Key name 4000CL Q 400 Clip Fast Access System Quantel Protocol PBIO Option 3 SYSTEM INSTALLATION a ST300 S SM VTR DDR CONTROLLER NOTE When switching protocols verify that U11 on the main board of the ST300 is a Dallas DS1245Y 1 Plug one end of a 9 conductor RS422 serial cable into the 9 pin connector VTR 1 VTR 2 VTR 3 or VTR 4 on the rear of the ST300 Plug the other end of the cable into
4. on a SINGLE CHANNEL ONLY Loop will automatically be disabled if the Channel becomes part of a gang If the clip ID ends with an asterisk it will automatically loop when either LOOP ENABLE or PLAY is pressed 4000CL Q 400 Clip Fast Access System Quantel Protocol PBIO Option 11 13 CREATE NEW CLIPS Set record mode using MENU Press SHIFT RECORD to set clip length Prompt will show Enter REC Duration Manually enter desired clip duration using numeric keypad on ST300 Press ENTER to save or ESC to exit without saving Press CLIP LIST Prompt will show CREATE NEW CLIP Press LOAD to create Press LOAD Prompt will show NEW CLIP Manually enter new clip name using numeric keypad or PC keyboard with KBIO option Press ENTER to create clip or ESC to exit without creating clip If clip is successfully created prompt will show Ready to Record Press REC or STOP Press REC to record Press STOP to pause record Press STOP again to terminate record 4000CL Q 400 Clip Fast Access System Quantel Protocol PBIO Option 12 14 TRANSFERRING CUELIST The TRANSMIT CUELIST function allows you to transmit your list of Cue Points to a PC using the provided utility software on the PC or to another ST300 Transfer to a PC requires OpSuite 3 0 software which runs on a Windows based computer Contact DNF Controls for more information a TRANSMIT
5. to exit without searching 10 PBIO ENABLE DISABLE On the ST300 press the PBIO key to enable or disable PBIO When disabled the ST300 will ignore all Pbus commands When enabled the ST300 will respond to all Pbus commands When enabled and Pbus commands are received the key s LED will flash 9 4000CL Q 400 Clip Fast Access System Quantel Protocol PBIO Option 10 11 TRIGGER The operator fires a trigger using either the Timeline or Run function on the production switcher The ST300 puts the Video Server into the following modes based upon the trigger value GRASS VALLEY GROUP VALUES Trigger Value Mode 0 Play 1 Recue to beginning of clip 2 Slo mo using ST300 Wheel Preset or T Bar Speed 3 Reverse Play 4 Still Frame 5 Play 8 or greater Play SONY VALUES Trigger Value Mode 0 Recue to beginning of clip 1 Play 2 Slo mo using ST300 Wheel Preset or T Bar Speed 3 Reverse Play 4 Still Frame 5 Play 8 or greater Play 12 LOOP CLIP LOAD a clip from CLIPLIST or RECALL a learned clip Press LOOP ENABLE The LOOP ENABLE indicator will turn on Press PLAY to loop a loaded clip The second line of the display will show Looping clip OR Press SHIFT PLAY The clip will be reloaded and start playing in a Loop Press STOP to stop the loop play NOTE The ST300 will NOT respond to any other keys while a clip is looping Only STOP is recognized in this mode NOTES The LOOP function can be performed
6. 1 EN 11144 and 3n9 LX3N 1sv1 Da ee a T a DA vu Cbs gee os H mee f ar El Ho al Will pe Jou MIT LAWS Oldd 0 190007 3 1 0 190007 0 190007 NI EL OO EL IIS 4000CL Q 400 Clip Fast Access System Ouantel Protocol PBIO Option 19 19 DNF CONTROLS LIMITED WARRANTY DNF Controls warrants its product to be free from defects in material and workmanship for a period of one 1 year from the date of sale to the original purchaser from DNF Controls In order to enforce the rights under this warranty the customer must first contact DNF s Customer Support Department to afford the opportunity of identifying and fixing the problem without sending the unit in for repair If DNF s Customer Support Department cannot fix the problem the customer will be issued a Returned Merchandise Authorization number RMA The customer will then ship the defective product prepaid to DNF Controls with the RMA number clearly indicated on the customer s shipping document The merchandise is to be shipped to DNF Controls 12843 Foothill Blvd Suite D Sylmar CA 91342 USA Failure to obtain a proper RMA number prior to returning the product may result in the return not being accepted or in a charge for the required repair DNF Controls at its option will repair or replace the defective unit DNF Controls will return the unit prepaid to the customer The method of shipment is at the discretion of DNF Controls principally UPS G
7. 12843 Foothill Blvd Suite D Sylmar CA 91342 818 898 3380 voice 818 898 3360 fax www dnfcontrols com Model No 4000CL Q PBIO amp 4000CL Q T 400 CLIP FAST ACCESS SYSTEM Quantel Protocol USER MANUAL 4000CL Q 400 Clip Fast Access System Quantel Protocol PBIO Option 1 Table of Contents 1 REVISION HISTORY GETTING STARTED 2 SYSTEM DESCRIPTION DEFINITIONS 3 SYSTEM INSTALLATION a ST300 S SM VTR DDR CONTROLLER b PRODUCTION SWITCHER 4 VIDEO SERVER SETUP 5 LOADA CLIP 6 VIEW THE CLIP ID OF THE CURRENTLY LOADED CLIP 7 LEARN A CLIP OR CLIP COMBINATION a LEARN ON THE PRODUCTION SWITCHER b LEARN ON THE ST300 8 RECALL A CLIP OR CLIP COMBINATION a RECALL ON THE PRODUCTION SWITCHER b RECALL ON THE ST300 9 RECUE THE CURRENTLY LOADED CLIP 10 PBIO ENABLE DISABLE 11 TRIGGER 12 LOOP CLIP 13 CREATE NEW CLIPS 14 TRANSFERRING CUELIST a TRANSMIT CUE LIST FUNCTION b RECEIVE CUE LIST FUNCTION REFERENCE 15 SETUP MENU 16 FUNCTION TABLE 17 SPECIFICATIONS 18 KEY LAYOUT 19 DNF CONTROLS LIMITED WARRANTY Manual Version eesssosseoooecscsoceosecsessccoceccccesssoococeeees 2 3 081004 Document ID ouucooooooooooooo 4000CL Q PBIO User Manual doc 2 4000CL Q 400 Clip Fast Access System Quantel Protocol PBIO Option NX Yvw0w0wv 0 00 Y A A Du Ya 14 14 16 17 19 20 1 REVISION HISTORY 072903 Rev 2 0 Changed Connection Diagram Changed Specification Sectio
8. ECTOR 9 Pin D Type Female Pin 1 Frame Ground 6 Receive Common 2 Receive A 7 Receive B 3 Transmit B gt 8 Transmit A gt 4 Transmit Common 9 Frame Ground 5 Spare POWER CONNECTOR 9 Pin D Type Male Pin 1 5v DC 6 5 VDC 2 5v DC 7 Ground 3 Ground 8 Ground 4 12 VDC 9 Ground 5 12 VDC AUX PORT RS422 SERIAL CONNECTOR 9 Pin D Type Female Pin 1 Frame Ground 6 Receive Common 2 Receive A 7 Receive B 3 Transmit B gt 8 Transmit A gt 4 Receive Common 9 Frame Ground 5 Spare 17 4000CL Q 400 Clip Fast Access System Quantel Protocol PBIO Option GPI IN OUT CONNECTOR 15 Pin D Type Female DB15F Pin Description Function Pin Description Function 1 GPI 1 Out 9 GPI 1 In Play 2 GPI 2 Out 10 GPI 2 In Stop 3 GPI 3 Out 11 GPI 3 In Recue 4 GPI 4 Out 12 GPI 4 In Next Cue 5 GPI 5 Out 13 GPI 5 In Last Cue 6 GPI 6 Out 14 GPI 6 In Recall 7 GPI 7 Out 15 GPI 7 In 8 Ground TURNAROUND ADAPTER DNF Side Quantel Side 9 Pin D Type Female 9 Pin D Type Male 1 Frame Ground 1 Frame Ground 2 Receive A 2 Transmit A gt 3 Transmit B gt 3 Receive B 4 Transmit Common 4 Transmit Common 5 No Connection 5 No Connection 6 Receive Common 6 Receive Common 7 Receive B 7 Transmit B gt 8 Transmit A gt 8 Receive A 9 Frame Ground 9 Frame Ground 18 4000CL Q 400 Clip Fast Access System Quantel Protocol PBIO Option KEY LAYOUT 18 STOHINOO 49 1013409 400 YLA 00815 T snf 319VN3 dio d00
9. a Turnaround Adapter then into the 9 pin REMOTE connector on the Video Server See specification section for Turnaround Wiring diagram 2 Connect the 5 12 12 VDC POWER SUPPLY into the POWER connector on the rear of the ST300 Plug the Power Supply into an outlet 90 VAC to 240 VAC 3 Check SETUP MENU prior to using the ST300 to confirm proper Record mode and other User settable modes Installation is complete Connection Diagram ST300 SSM REF VIDEO AUX Q UA N TE L E LCD POWER ES Li CONTRAST S E R VE R 00000 Alles Jo RESET PINT 5v PIN3 GND Turnaround POWER SUPPLY 5 4000CL Q 400 Clip Fast Access System Quantel Protocol PBIO Option b PRODUCTION SWITCHER 1 Connect a RS422 9 pin serial cable to the AUX connector on the rear of the ST300 Connect the other end of the cable to the Peripheral Bus Connector on the production switcher Communication Format 38 4K 8 1 2 To select a Production Switcher type Default Grass Valley Group a Press MENU to turn the Wheel until SWITCHER is displayed b Press Softkey to toggle between Sony and Grass Valley c Press ESC at anytime to exit MENU mode 3 The ST300 has 4 Peripheral Device Addresses one for each VTR that it controls To set the Device Address for each VTR a Press MENU and turn the wheel until Peripheral Address is displayed b Press VTR 1 VTR 2 VTR 3 or VTR
10. ey to toggle Video V Audiol A1 Audio2 A2 Audio3 A3 Audio4 A4 on off WIND MODE Press Softkey to select HOLD fast wind is maintained only while key is depressed OR LATCH fast wind is initiated and maintained with momentary key press Select fast wind speed 3 9 to 23 7 by pressing Softkey below SPD SLOMO ST300 display shows SLOMO with WHEEL Non T Bar version m SpdRange Preset ST300 display shows SLOMO with TBAR T Bar version Wheel SpdRange Preset NOTE The T BAR has a fixed speed range of 0 gt 200 with a detent at 100 play speed For Wheel only Press Softkey SPDRANGE to select SLOMO speed ranges Press Softkey to select 0 gt 200 OR 100 gt 200 Press Softkey BACK to return to SLOMO MENU Press ESC to exit OR Turn the Wheel to select another item Continued on next page 14 4000CL 9 400 Clip Fast Access System Quantel Protocol PBIO Option For Wheel only Press Softkey PRSET to select the SLOMO Preset Speed Mode Press Softkey UPDATE When exiting SLOMO mode the last used speed is saved in the Preset Speed register Press Softkey STATIC The Preset Speed register is NOT updated when exiting SLOMO mode It is only changed by SHIFT SLOMO PRESET SLOMO ST300 SETUP ST300 SETUP Clear Cues SetDefault Press Softkey beneath ClearCues to clear all Cue Points to 00 00 00 00 Press Softkey YES
11. he current Cue Point If the VTRs are ganged select one VTR that is part of the Gang The rest of the Gang will be learned automatically 5 Press MARK to complete the LEARN OR Press ESC to exit without LEARNING The ST300 will LEARN save the VTR Number 1 2 3 4 loaded CLIP ID and current IN time to the selected Cue Point 8 4000CL Q 400 Clip Fast Access System Quantel Protocol PBIO Option 8 RECALL A CLIP OR CLIP COMBINATION a RECALL ON THE PRODUCTION SWITCHER RECALL the desired REGISTER NUMBER The ST300 will automatically load the Learned clips on the Learned VTRs cue the clips to the Learned time then set the Learned GANG mode b RECALL ON THE ST300 1 Select the desired Cue Point by pressing NEXT CUE LAST CUE or by manually entering the Cue Point using the numeric keypad The selected Cue Point number is shown on the bottom line of the display 2 Press LOAD on the ST300 The ST300 will automatically load the Learned clips on the Learned VTRs cue the clips to the Learned time then set the Learned GANG mode 9 RECUE THE CURRENTLY LOADED CLIP Press RECUE If an IN Point is marked the IN indicator is on the clip will RECUE to the IN Point If the IN point is not marked the clip will RECUE to the start of the clip OR Press SHIFT RECUE a Enter the desired time to search to using the ST300 s numeric keypad b Press ENTER to search to the entered time OR Press ESC
12. n Added Loop Clip Section Changed Key Layout 112403 Rev 2 1 Company header information revised Added DNF Controls Limited Warranty 013004 Rev 2 2 Added Transferring Cue List section 081004 Rev 2 3 Changed T bar dimension 3 4000CL Q 400 Clip Fast Access System Quantel Protocol PBIO Option Getting Started 2 4 SYSTEM DESCRIPTION NOW production switchers can load amp play video clips on Quantel Video Servers Q Use the EMEM or SNAPSHOT Learn amp Recall functions of the production switcher to load and play a video clip from a Recall or timeline Q Use the Run and Trigger functions of the production switcher to Play Stop or Recue the video clip The 400 Clip Fast Access System consists of the ST300 SSM VTR Controller and Shotlist Software The Video Server must support Quantel Protocol The PERIPHERAL BUS INTERFACE Option for the ST300 VTR Controller is special software in the ST300 With this Option the ST300 has 4 Peripheral Device Addresses one for each VTR that it controls This allows the production switcher to control any and all VTRs connected to the ST300 Upon receipt of the Learn command from the production switcher the ST300 saves the CLIP IDs of the currently loaded clips the current time of each clip the VTRs they are loaded on and the current GANG mode into the appropriate Cue Point When the Recall command is received the ST300 loads the Learned Clips onto the Learned
13. oard if KBIO option Press LOAD to load the selected CLIP ID for playout If more than one Clip ID matches the entered selected ID the display will show More Than 1 Found Using the wheel scroll through the list of clips Select the desired clip then press LOAD Repeat steps a d to load clips on desired VTRs Set the GANG mode if required VIEW THE CLIP ID OF THE CURRENTLY LOADED CLIP Press SHIFT LOAD The bottom line will show the name of the loaded clip 4000CL Q 400 Clip Fast Access System Quantel Protocol PBIO Option 7 LEARN A CLIP OR CLIP COMBINATION a LEARN ON THE PRODUCTION SWITCHER 1 On the production Switcher select and enable the Peripheral Device Addresses for the ST300 2 Do a LEARN to the desired REGISTER The ST300 will LEARN save the VTR number loaded CLIP IDs and current time into the REGISTER number in the ST300 b LEARN ON THE ST300 1 Load a clip on the desired VTRs See Section 4 LOAD A CLIP 2 Select the desired Cue Point by pressing NEXT CUE LAST CUE or by manually entering the Cue Point using the numeric keypad followed by ENTER The selected Cue Point number is shown on the bottom line of the display 3 Press SHIFT MARK to start the LEARN The first line of the display will show Select VTRs The second line of the display will show Mark Lrn ESC cancel 4 Press VTR 1 2 3 or 4 to select the VTR to be learned into t
14. om the VTR4 connector of the transmitting ST300 using RS422 9 pin cable with TX and RX lines crossed A Turnaround Cable b Press MENU and scroll the Wheel to Receive CUE List YES Enter Exit ESC c Press ENTER from start receiving The Display shows Waiting to receive on the first line d When the Transmitter is ready transfer starts automatically The Display now shows Receiving cuelist e After the transfer is over the display shows Done Success Press any key f Press any key The display shows Receive cuelist message g Press ESC to exit the MENU mode 2 To Receive Cue Points from the PC a Connect the VTR4 connector on the back of the ST300 to one of the COM ports on the PC using RS422 to RS232 adapter b Repeat steps b g of the RECEIVE CUE POINTS from the ST300 section 4000CL Q 400 Clip Fast Access System Quantel Protocol PBIO Option Reference 15 SETUP MENU Q Press MENU The MENU indicator will turn on Q Turn the Wheel to select item to change Q Press MENU OR use the Softkeys to change the desired mode for that option Q Turn the Wheel at anytime to select another item Q Press ESC at anytime to exit SETUP MENU The MENU indicator will turn off MENU MODES Turning Wheel clockwise RECORD Press MENU to select the desired record mode Lockout Assemble Crash Full or Insert Only in INSERT mode Press the associated Softk
15. round for shipments within the United States of America Shipments to international customers will be sent via air Should a customer require the product to be returned in a more expeditious manner the return shipment will be billed to their freight account This warranty will be considered null and void if accident misuse abuse improper line voltage fire water lightning or other acts of God damaged the product All repair parts are to be supplied by DNF Controls either directly or through its authorized dealer network Similarly any repair work not performed by either DNF Controls or its authorized dealer may void the warranty After the warranty period has expired DNF Controls offers repair services at prices listed in the DNF Controls Price List DNF Controls reserves the right to refuse repair of any unit outside the warranty period that is deemed non repairable DNF Controls shall not be liable for direct indirect incidental consequential or other types of damage resulting from the use of the product 20 4000CL Q 400 Clip Fast Access System Quantel Protocol PBIO Option
16. t Cue Point Location RECORD REC Places VTR into the Record mode selected by RECORD MODE in the SETUP MENU Press RECORD or RECORD PLAY REWIND RWD Press and HOLD to shuttle Release key to stop Set WIND Speed in MENU SHUTTLE SHUTTLE Select SHUTTLE mode and enable Wheel SLOMO SLOMO Press SLOMO to slo mo the VTR Turn the wheel or move the T Bar if available to change the play speed Press SLOMO to STILL frame OR press any transport key to exit SLOMO SLO MO SHIFT SLOMO For WHEEL ONLY To preset the slo mo speed Turn SPEED PRESET wheel to select desired speed Press ESC or any transport key to exit Press once to STILL frame VTR Press again to put VTR into STOP mode TIME MODE TIME MODE Press to toggle between Timecode TC VITC VT or Tape SELECT Timer TM display modes 16 4000CL Q 400 Clip Fast Access System Quantel Protocol PBIO Option 17 SPECIFICATIONS ST300 Power Size Weight Rear Panel Connectors Display Jog Shuttle Wheel Optional T bar 90 VAC to 265 VAC adapter supplied with IEC connector L x W x H 12 x 6 x 1 5 front 3 0 rear T Bar unit is 12 6 long 4 Ibs VTRI VTR2 VTR3 VTR4 All DB9F GPI DBF15F Power DB9M Aux DB9F Reference Video BNC Easy to read 2 line back lit LCD display User adjustable contrast With mechanical detents Slo mo 0 200 of Play Speed VTR RS422 SERIAL CONN
17. when asked Are You Sure Press Softkey beneath SetDefault to set ST300 to default settings Press Softkey YES when asked Are You Sure DISPLAY The version number for the currently installed software is displayed SOFTWARE VERSION SYNC OFF or ON PBIO ADDRESS Press VTR1 VTR2 VTR3 or VTR4 key to select a VTR To assign a PBIO address enter the desired address number on the numeric keypad Repeat for all VTRs assigned SWITCHER Select your switcher type GVG Grass Valley Group default or Sony TYPE For Philips DD35 with PBus use GVG PARITY Select Switcher s Parity type ODD EVEN or NONE 15 4000CL O 400 Clip Fast Access System Quantel Protocol PBIO Option 16 FUNCTION TABLE GOTO SHIFT RECUE Search the VTR to the manually entered time ENTERED TIME Use the ST300 numeric keypad Press ENTER or RECUE SHIFT VTR 1 Individually press the VTR keys to be included in the gang OR The LED above the key will turn on Press the VTR key SHIFT VTR 2 again to remove from gang The LED above the key will OR turn off Press ESC to exit SHIFT VTR 3 OR The VTR LEDs that are on show the gang SHIFT VTR 4 The flashing LED shows which VTR is currently selected FFWD FF WD Press and HOLD to shuttle Release key to stop Set WIND Speed in MENU JOG Select JOG mode and enable Wheel LAST CUE LAST CUE Step to the previous Cue Point Location NEXT CUE NEXT CUE Step to the nex
Download Pdf Manuals
Related Search